ted 111tools and their uses
TRANSCRIPT
![Page 1: Ted 111Tools and their Uses](https://reader031.vdocument.in/reader031/viewer/2022021918/58a779e11a28abef478b4623/html5/thumbnails/1.jpg)
![Page 2: Ted 111Tools and their Uses](https://reader031.vdocument.in/reader031/viewer/2022021918/58a779e11a28abef478b4623/html5/thumbnails/2.jpg)
The Objective of this section is to
enable the trainee to:enable the trainee to:
Choose, maintain and use the most
suitable marking out and measuring
equipment.
![Page 3: Ted 111Tools and their Uses](https://reader031.vdocument.in/reader031/viewer/2022021918/58a779e11a28abef478b4623/html5/thumbnails/3.jpg)
Task No. Knowledge requirements
7.1 Identify and describe the use of marking out and measuring equipment, tools and instruments.
7.2 Compare the relative degrees of accuracy of marking out and measuring equipment listed.
7.3 Identify methods of marking out.
7.4 Identify datum and describe methods of marking out from them.
7.5 Describe how to avoid faults and minimize inaccuracies when marking out7.5 Describe how to avoid faults and minimize inaccuracies when marking out
7.6 Identify and describe the operation of tools and equipment for angular marking out and
measurement.
7.7 Identify and explain the use of the precision bubble level to establish horizontal and vertical planes.
7.8 Identify and explain the use of the plumb bob to establish vertical planes.
7.9 Identify template materials for given situations and describe their use.
7.10 Identify and explain the main classes of fit.
![Page 4: Ted 111Tools and their Uses](https://reader031.vdocument.in/reader031/viewer/2022021918/58a779e11a28abef478b4623/html5/thumbnails/4.jpg)
7.1Identify and describe the use of marking out
and measuring equipment, tools and 7.1 and measuring equipment, tools and
instruments.
![Page 5: Ted 111Tools and their Uses](https://reader031.vdocument.in/reader031/viewer/2022021918/58a779e11a28abef478b4623/html5/thumbnails/5.jpg)
A measurement is a comparison to a standard.
Measurement is the process or the result of determining the magnitude of a quantity, such as length or mass, relative to a unit of measurement, such as a meter or a kilogram.
For example length, width , depth , height , temperature , density etc.
Lecture 1/7
For example length, width , depth , height , temperature , density etc.
Metrology is the science of measurement.
![Page 6: Ted 111Tools and their Uses](https://reader031.vdocument.in/reader031/viewer/2022021918/58a779e11a28abef478b4623/html5/thumbnails/6.jpg)
The metric system is a decimal system of measurement based on its units.
A. Length is measured in meter (m), centimeter (cm), or millimeter
1.Metric System
Lecture 1/7
A. Length is measured in meter (m), centimeter (cm), or millimeter (mm) etc.
![Page 7: Ted 111Tools and their Uses](https://reader031.vdocument.in/reader031/viewer/2022021918/58a779e11a28abef478b4623/html5/thumbnails/7.jpg)
B. Mass is measured in kilogram (kg) or grams (gm)
1.Metric System
Lecture 1/7
![Page 8: Ted 111Tools and their Uses](https://reader031.vdocument.in/reader031/viewer/2022021918/58a779e11a28abef478b4623/html5/thumbnails/8.jpg)
C. Time is measured in second (s), minute (min) or hour (hr)
1.Metric System
Lecture 1/7
![Page 9: Ted 111Tools and their Uses](https://reader031.vdocument.in/reader031/viewer/2022021918/58a779e11a28abef478b4623/html5/thumbnails/9.jpg)
D. Temperature is measured in degree centigrade (0C)
1.Metric System
Lecture 1/7
![Page 10: Ted 111Tools and their Uses](https://reader031.vdocument.in/reader031/viewer/2022021918/58a779e11a28abef478b4623/html5/thumbnails/10.jpg)
2.S.I. System
The International System of Units is the modern revision of the metric system. It is the world's most widely used system of units, both in everyday commerce and in science.
Lecture 1/7
SI unit of length meter (m) SI unit of mass kilogram (kg)SI unit of time second (s)SI unit of temperature Kelvin (K)
![Page 11: Ted 111Tools and their Uses](https://reader031.vdocument.in/reader031/viewer/2022021918/58a779e11a28abef478b4623/html5/thumbnails/11.jpg)
Measuring Tools
A ruler, sometimes called a rule or line gauge, is an instrument used in geometry, technical drawing, printing and engineering to measure distances and/or to rule straight lines.
1.Ruler
Lecture 1/7
![Page 12: Ted 111Tools and their Uses](https://reader031.vdocument.in/reader031/viewer/2022021918/58a779e11a28abef478b4623/html5/thumbnails/12.jpg)
Desk rulers are used for three main purposes: to measure, to aid in drawing straight lines and as a straight guide for cutting and scoring with a blade. Practical rulers have distance markings along their edges.
1.Ruler
Lecture 1/7
Measuring Tools
![Page 13: Ted 111Tools and their Uses](https://reader031.vdocument.in/reader031/viewer/2022021918/58a779e11a28abef478b4623/html5/thumbnails/13.jpg)
A measuring tape is a flexible form of ruler.
2.Measuring Tape
Lecture 1/7
Measuring Tools
![Page 14: Ted 111Tools and their Uses](https://reader031.vdocument.in/reader031/viewer/2022021918/58a779e11a28abef478b4623/html5/thumbnails/14.jpg)
It consists of a ribbon of cloth, plastic, or metal strip with linear-measurement markings. It is a common measuring tool. Its flexibility allows for a measure of great length to be easily carried in pocket or toolkit and permits one to measure around curves or corners.
2.Measuring Tape
Lecture 1/7
Measuring Tools
![Page 15: Ted 111Tools and their Uses](https://reader031.vdocument.in/reader031/viewer/2022021918/58a779e11a28abef478b4623/html5/thumbnails/15.jpg)
A Vernier caliper is precision measuring tool.
3. Vernier Caliper
We can measure inside, outside and depth.
It has locknut which is very useful to keep the measurement permanently.
Lecture 1/7
Measuring Tools
![Page 16: Ted 111Tools and their Uses](https://reader031.vdocument.in/reader031/viewer/2022021918/58a779e11a28abef478b4623/html5/thumbnails/16.jpg)
3. Vernier Caliper
Lecture 1/7
Measuring Tools
![Page 17: Ted 111Tools and their Uses](https://reader031.vdocument.in/reader031/viewer/2022021918/58a779e11a28abef478b4623/html5/thumbnails/17.jpg)
Outside jaws: 1. used to measure external diameter or width of anobject.
Parts of Vernier Caliper
Inside jaws: 2. used to measure internal diameter of an object.
Lecture 1/7
Measuring Tools
![Page 18: Ted 111Tools and their Uses](https://reader031.vdocument.in/reader031/viewer/2022021918/58a779e11a28abef478b4623/html5/thumbnails/18.jpg)
Depth probe: 3. used to measure depths of an object or a hole.
Parts of Vernier Caliper
Main scale: 4. scale marked every mm.
Lecture 1/7
Measuring Tools
![Page 19: Ted 111Tools and their Uses](https://reader031.vdocument.in/reader031/viewer/2022021918/58a779e11a28abef478b4623/html5/thumbnails/19.jpg)
Main scale: 5. scale marked in inches and fractions.
Vernier : 6. gives interpolated measurements to 1/10 mm or better.
Parts of Vernier Caliper
Lecture 1/7
Measuring Tools
![Page 20: Ted 111Tools and their Uses](https://reader031.vdocument.in/reader031/viewer/2022021918/58a779e11a28abef478b4623/html5/thumbnails/20.jpg)
Vernier : 7. gives interpolated measurements in fractions of an inch.
Parts of Vernier Caliper
Retainer: 8. used to block movable part to allow the easy transferringof a measurement.
3. Measuring Tools
Lecture 1/7
![Page 21: Ted 111Tools and their Uses](https://reader031.vdocument.in/reader031/viewer/2022021918/58a779e11a28abef478b4623/html5/thumbnails/21.jpg)
Reading Vernier Caliper
Lecture 1/7
![Page 22: Ted 111Tools and their Uses](https://reader031.vdocument.in/reader031/viewer/2022021918/58a779e11a28abef478b4623/html5/thumbnails/22.jpg)
Reading Vernier Caliper
Lecture 1/7
![Page 23: Ted 111Tools and their Uses](https://reader031.vdocument.in/reader031/viewer/2022021918/58a779e11a28abef478b4623/html5/thumbnails/23.jpg)
Reading Vernier Caliper
Lecture 1/7
![Page 24: Ted 111Tools and their Uses](https://reader031.vdocument.in/reader031/viewer/2022021918/58a779e11a28abef478b4623/html5/thumbnails/24.jpg)
A micrometer is also called micrometer screw gauge.
4. Micrometer
It is used for precise measurement.
The least count of Micrometer is 0.001 mm
Lecture 1/7
Measuring Tools
The least count of Micrometer is 0.001 mm
![Page 25: Ted 111Tools and their Uses](https://reader031.vdocument.in/reader031/viewer/2022021918/58a779e11a28abef478b4623/html5/thumbnails/25.jpg)
4. Micrometer
Lecture 1/7
Measuring Tools
![Page 26: Ted 111Tools and their Uses](https://reader031.vdocument.in/reader031/viewer/2022021918/58a779e11a28abef478b4623/html5/thumbnails/26.jpg)
Frame : The C-shaped body that holds the anvil and barrel.Parts of Micrometer
Anvil : The shiny part that the spindle moves toward, andthat the sample rests against.
Lecture 1/7
Measuring Tools
![Page 27: Ted 111Tools and their Uses](https://reader031.vdocument.in/reader031/viewer/2022021918/58a779e11a28abef478b4623/html5/thumbnails/27.jpg)
Parts of MicrometerThimble : The part that one's thumb turns. Graduated markings.
Thimble lock : The knurled part that one can tighten to hold the spindlestationary.
Lecture 1/7
Measuring Tools
![Page 28: Ted 111Tools and their Uses](https://reader031.vdocument.in/reader031/viewer/2022021918/58a779e11a28abef478b4623/html5/thumbnails/28.jpg)
Parts of MicrometerSpindle : The shiny cylindrical part that the thimble causes to
move toward the anvil
Sleeve : The stationary round part with the linear scale on it.It is also called barrel or stock.
Lecture 1/7
Measuring Tools
![Page 29: Ted 111Tools and their Uses](https://reader031.vdocument.in/reader031/viewer/2022021918/58a779e11a28abef478b4623/html5/thumbnails/29.jpg)
A. Outside micrometerThese are typically used to measure wires, spheres, shaftsand blocks.
Types of MicrometerThe names are based on their application:
Lecture 2/7
Measuring Tools
and blocks.
![Page 30: Ted 111Tools and their Uses](https://reader031.vdocument.in/reader031/viewer/2022021918/58a779e11a28abef478b4623/html5/thumbnails/30.jpg)
B. Inside micrometer
Types of Micrometer
Used to measure the diameter of holes.
Lecture 2/7
Measuring Tools
![Page 31: Ted 111Tools and their Uses](https://reader031.vdocument.in/reader031/viewer/2022021918/58a779e11a28abef478b4623/html5/thumbnails/31.jpg)
C. Depth micrometer
Types of Micrometer
Measures depths of slots and steps.
Lecture 2/7
Measuring Tools
![Page 32: Ted 111Tools and their Uses](https://reader031.vdocument.in/reader031/viewer/2022021918/58a779e11a28abef478b4623/html5/thumbnails/32.jpg)
1 mmReading Micrometer
Lecture 2/7
![Page 33: Ted 111Tools and their Uses](https://reader031.vdocument.in/reader031/viewer/2022021918/58a779e11a28abef478b4623/html5/thumbnails/33.jpg)
1+0.75 mm Reading Micrometer
Lecture 2/7
![Page 34: Ted 111Tools and their Uses](https://reader031.vdocument.in/reader031/viewer/2022021918/58a779e11a28abef478b4623/html5/thumbnails/34.jpg)
1+0.75+0=1.75mm Reading Micrometer
Lecture 2/7
![Page 35: Ted 111Tools and their Uses](https://reader031.vdocument.in/reader031/viewer/2022021918/58a779e11a28abef478b4623/html5/thumbnails/35.jpg)
A height gauge is a
measuring device used
either for determining the
5. Height gauge
Lecture 2/7
Measuring Tools
either for determining the
height of something, or
for repetitious marking of
items to be worked on.
![Page 36: Ted 111Tools and their Uses](https://reader031.vdocument.in/reader031/viewer/2022021918/58a779e11a28abef478b4623/html5/thumbnails/36.jpg)
5. Height gauge
This measuring tool is used in metal working or metrology to
either set or measure vertical distances.
Lecture 2/7
Measuring Tools
![Page 37: Ted 111Tools and their Uses](https://reader031.vdocument.in/reader031/viewer/2022021918/58a779e11a28abef478b4623/html5/thumbnails/37.jpg)
6. Feeler gauge
A feeler gauge is a simple tool used to measure gap widths. Feeler
gauges are mostly used in engineering to measure the clearance
between two parts.
Lecture 2/7
Measuring Tools
between two parts.
![Page 38: Ted 111Tools and their Uses](https://reader031.vdocument.in/reader031/viewer/2022021918/58a779e11a28abef478b4623/html5/thumbnails/38.jpg)
(i) They consist of a number of
small lengths of steel of different
thicknesses with
measurements marked on each
6. Feeler gauge
Lecture 2/7
Measuring Tools
measurements marked on each
piece.
(ii) They are flexible enough that,
even if they are all on the same
hinge, several can be stacked
together to gauge intermediate
values.
![Page 39: Ted 111Tools and their Uses](https://reader031.vdocument.in/reader031/viewer/2022021918/58a779e11a28abef478b4623/html5/thumbnails/39.jpg)
7. Thread gauge
A thread pitch gauge, also known as a screw pitch gauge or
pitch gauge, is used to measure the pitch or lead of a screw
thread.
Lecture 2/7
Measuring Tools
![Page 40: Ted 111Tools and their Uses](https://reader031.vdocument.in/reader031/viewer/2022021918/58a779e11a28abef478b4623/html5/thumbnails/40.jpg)
(i) Is used as a precision measuring instrument.
(ii) Allows the user to determine the profile of the given thread.
(iii) Allows to categorize the thread by shape and pitch.
7. Thread gauge
Lecture 2/7
Measuring Tools
![Page 41: Ted 111Tools and their Uses](https://reader031.vdocument.in/reader031/viewer/2022021918/58a779e11a28abef478b4623/html5/thumbnails/41.jpg)
It is used as a reference for the setting of
measuring equipment used in machine shops,
such as micrometers, calipers, and dial
8. Slip gauge
Lecture 2/7
Measuring Tools
such as micrometers, calipers, and dial
indicators (when used in an inspection role).
A slip gauge also known as a gage block, a
precision ground and lapped length measuring
standard.
![Page 42: Ted 111Tools and their Uses](https://reader031.vdocument.in/reader031/viewer/2022021918/58a779e11a28abef478b4623/html5/thumbnails/42.jpg)
Lecture 2/7
![Page 43: Ted 111Tools and their Uses](https://reader031.vdocument.in/reader031/viewer/2022021918/58a779e11a28abef478b4623/html5/thumbnails/43.jpg)
The inside caliper is used to measure
9. Inside caliper
Lecture 3/7
Measuring Tools
The inside caliper is used to measure
the internal size of an object.
![Page 44: Ted 111Tools and their Uses](https://reader031.vdocument.in/reader031/viewer/2022021918/58a779e11a28abef478b4623/html5/thumbnails/44.jpg)
The Inside caliper requires
manual adjustment prior to
fitting, fine setting of this caliper
Use of Inside caliper
Lecture 3/7
Measuring Tools
fitting, fine setting of this caliper
type is performed by tapping the
caliper legs lightly on a handy
surface until they will almost pass
over the object.
![Page 45: Ted 111Tools and their Uses](https://reader031.vdocument.in/reader031/viewer/2022021918/58a779e11a28abef478b4623/html5/thumbnails/45.jpg)
Types of Inside caliper
a. Firm joint inside caliper
Lecture 3/7
Measuring Tools
![Page 46: Ted 111Tools and their Uses](https://reader031.vdocument.in/reader031/viewer/2022021918/58a779e11a28abef478b4623/html5/thumbnails/46.jpg)
Types of Inside caliper
b. Adjustable Screw inside caliper
Lecture 3/7
Measuring Tools
b. Adjustable Screw inside caliper
![Page 47: Ted 111Tools and their Uses](https://reader031.vdocument.in/reader031/viewer/2022021918/58a779e11a28abef478b4623/html5/thumbnails/47.jpg)
Outside calipers are used to measure the external
size of an object.
10. Outside caliper
Lecture 3/7
Measuring Tools
![Page 48: Ted 111Tools and their Uses](https://reader031.vdocument.in/reader031/viewer/2022021918/58a779e11a28abef478b4623/html5/thumbnails/48.jpg)
The Outside caliper requires
manual adjustment prior to
fitting, fine setting of this
Use of outside caliper
Lecture 3/7
Measuring Tools
fitting, fine setting of this
caliper type is performed by
tapping the caliper legs lightly
on a handy surface until they
will almost pass over the object.
![Page 49: Ted 111Tools and their Uses](https://reader031.vdocument.in/reader031/viewer/2022021918/58a779e11a28abef478b4623/html5/thumbnails/49.jpg)
Types of outside caliper
a. Firm joint outside caliper
Lecture 3/7
Measuring Tools
a. Firm joint outside caliper
![Page 50: Ted 111Tools and their Uses](https://reader031.vdocument.in/reader031/viewer/2022021918/58a779e11a28abef478b4623/html5/thumbnails/50.jpg)
Types of outside caliper
b. Adjustable Screw outside caliper
Lecture 3/7
Measuring Tools
b. Adjustable Screw outside caliper
![Page 51: Ted 111Tools and their Uses](https://reader031.vdocument.in/reader031/viewer/2022021918/58a779e11a28abef478b4623/html5/thumbnails/51.jpg)
11. Surface plate/table
A surface plate is a solid, flat
plate used as the main horizontal
Lecture 3/7
Measuring Tools
plate used as the main horizontal
reference plane for precision
inspection, marking out and
tooling setup.
The surface plate is often used as
the baseline for all
measurements to the work piece.
![Page 52: Ted 111Tools and their Uses](https://reader031.vdocument.in/reader031/viewer/2022021918/58a779e11a28abef478b4623/html5/thumbnails/52.jpg)
12. Parallel Blocks
Lecture 3/7
Measuring Tools
![Page 53: Ted 111Tools and their Uses](https://reader031.vdocument.in/reader031/viewer/2022021918/58a779e11a28abef478b4623/html5/thumbnails/53.jpg)
13. V Block
Lecture 3/7
Measuring Tools
![Page 54: Ted 111Tools and their Uses](https://reader031.vdocument.in/reader031/viewer/2022021918/58a779e11a28abef478b4623/html5/thumbnails/54.jpg)
14. Dial Indicator
Dial indicator is used for
sensing or detecting
Lecture 3/7
Measuring Tools
sensing or detecting
small movements or size
variations in a work piece.
![Page 55: Ted 111Tools and their Uses](https://reader031.vdocument.in/reader031/viewer/2022021918/58a779e11a28abef478b4623/html5/thumbnails/55.jpg)
14. Dial Indicator
3. Measuring Tools
Lecture 3/7
![Page 56: Ted 111Tools and their Uses](https://reader031.vdocument.in/reader031/viewer/2022021918/58a779e11a28abef478b4623/html5/thumbnails/56.jpg)
Marking out is the process of transferring a design or pattern
to a work piece.
Marking Out
Marking Out Tools
Lecture 4/7
![Page 57: Ted 111Tools and their Uses](https://reader031.vdocument.in/reader031/viewer/2022021918/58a779e11a28abef478b4623/html5/thumbnails/57.jpg)
1. Divider
Divider calipers are used in the
process of marking out suitable
work pieces.
Lecture 4/7
Marking Out Tools
The points are sharpened so that
they act as scribers, one leg can
then be placed in the dimple
created by a center punch and the
other leg pivoted so that it scribes
a line on the work piece's surface,
thus forming an arc or circle.
![Page 58: Ted 111Tools and their Uses](https://reader031.vdocument.in/reader031/viewer/2022021918/58a779e11a28abef478b4623/html5/thumbnails/58.jpg)
1. Divider
Lecture 4/7
Marking Out Tools
![Page 59: Ted 111Tools and their Uses](https://reader031.vdocument.in/reader031/viewer/2022021918/58a779e11a28abef478b4623/html5/thumbnails/59.jpg)
2. Odd leg Caliper
Odd leg caliper is generally
used to scribe a line at a set
Lecture 4/7
Marking Out Tools
used to scribe a line at a set
distance from the edge of
work piece.
![Page 60: Ted 111Tools and their Uses](https://reader031.vdocument.in/reader031/viewer/2022021918/58a779e11a28abef478b4623/html5/thumbnails/60.jpg)
2. Odd leg Caliper
The bent leg is used to run along
the work piece edge while the
scriber makes its mark at a
Lecture 4/7
Marking Out Tools
scriber makes its mark at a
predetermined distance, this
ensures a line parallel to the edge.
![Page 61: Ted 111Tools and their Uses](https://reader031.vdocument.in/reader031/viewer/2022021918/58a779e11a28abef478b4623/html5/thumbnails/61.jpg)
3. Trammel
Trammels are used for
marking purpose where
Lecture 4/7
Marking Out Tools
marking purpose where
we can not use divider.
![Page 62: Ted 111Tools and their Uses](https://reader031.vdocument.in/reader031/viewer/2022021918/58a779e11a28abef478b4623/html5/thumbnails/62.jpg)
3. Trammel
Lecture 4/7
Marking Out Tools
![Page 63: Ted 111Tools and their Uses](https://reader031.vdocument.in/reader031/viewer/2022021918/58a779e11a28abef478b4623/html5/thumbnails/63.jpg)
4. Centre punch
A center punch is used to
mark the center of a point.
Lecture 3/7
Marking Out Tools
mark the center of a point.
![Page 64: Ted 111Tools and their Uses](https://reader031.vdocument.in/reader031/viewer/2022021918/58a779e11a28abef478b4623/html5/thumbnails/64.jpg)
4. Centre punch
It is usually used to mark the center of a hole
when drilling holes. A center punch forms a large
enough dimple to "guide" the tip of the drill bit.
Lecture 4/7
Marking Out Tools
enough dimple to "guide" the tip of the drill bit.
![Page 65: Ted 111Tools and their Uses](https://reader031.vdocument.in/reader031/viewer/2022021918/58a779e11a28abef478b4623/html5/thumbnails/65.jpg)
5. Scriber dot
A scriber is a hand tool
used in metalworking to
mark lines on work pieces,
Lecture 4/7
Marking Out Tools
mark lines on work pieces,
prior to machining.
The process of using a
scriber is called scribing.
![Page 66: Ted 111Tools and their Uses](https://reader031.vdocument.in/reader031/viewer/2022021918/58a779e11a28abef478b4623/html5/thumbnails/66.jpg)
6. Hammer
A ball-peen also known as a blacksmith's, engineer's
or machinist's hammer, is a type of peen hammer
used in metalworking.
Lecture 4/7
Marking Out Tools
used in metalworking.
![Page 67: Ted 111Tools and their Uses](https://reader031.vdocument.in/reader031/viewer/2022021918/58a779e11a28abef478b4623/html5/thumbnails/67.jpg)
6. Hammer
It is distinguished from a point-peen hammer or
chisel-peen hammer by having a hemispherical head.
Lecture 4/7
Marking Out Tools
![Page 68: Ted 111Tools and their Uses](https://reader031.vdocument.in/reader031/viewer/2022021918/58a779e11a28abef478b4623/html5/thumbnails/68.jpg)
Lecture 1/7
7.3 Identify methods of marking 7.3 Identify methods of marking
out.
![Page 69: Ted 111Tools and their Uses](https://reader031.vdocument.in/reader031/viewer/2022021918/58a779e11a28abef478b4623/html5/thumbnails/69.jpg)
Marking Straight Lines
Where a straight line is
required between two
points, a rule can be used or,
Lecture 4/7
Methods of Marking out
points, a rule can be used or,
for longer distances, a
straight edge.
![Page 70: Ted 111Tools and their Uses](https://reader031.vdocument.in/reader031/viewer/2022021918/58a779e11a28abef478b4623/html5/thumbnails/70.jpg)
Marking Circles and Arcs
Dividers are used to scribe
circular lines and Arcs. The
leg about which the dividers
Lecture 4/7
Methods of Marking out
leg about which the dividers
pivot is usually located in a
fine centre dot mark. To
locate the point of this leg
accurately it is essential to
use a sharp dot punch as
shown
![Page 71: Ted 111Tools and their Uses](https://reader031.vdocument.in/reader031/viewer/2022021918/58a779e11a28abef478b4623/html5/thumbnails/71.jpg)
Marking Circles and Arcs
Lecture 4/7
Methods of Marking out
![Page 72: Ted 111Tools and their Uses](https://reader031.vdocument.in/reader031/viewer/2022021918/58a779e11a28abef478b4623/html5/thumbnails/72.jpg)
Marking Circles and Arcs
Lecture 4/7
Methods of Marking out
![Page 73: Ted 111Tools and their Uses](https://reader031.vdocument.in/reader031/viewer/2022021918/58a779e11a28abef478b4623/html5/thumbnails/73.jpg)
Marking Circles and Arcs
Lecture 4/7
Methods of Marking out
![Page 74: Ted 111Tools and their Uses](https://reader031.vdocument.in/reader031/viewer/2022021918/58a779e11a28abef478b4623/html5/thumbnails/74.jpg)
Marking Large Diameter Circles
Trammel is used to draw a large diameter circle or arc.
Lecture 4/7
Methods of Marking out
![Page 75: Ted 111Tools and their Uses](https://reader031.vdocument.in/reader031/viewer/2022021918/58a779e11a28abef478b4623/html5/thumbnails/75.jpg)
Marking Lines Parallel Or Perpendicular The
To Surface Plate
A scribing block or surface gauge is used for marking out
lines parallel to a datum edge or a datum surface.
Lecture 5/7
Methods of Marking out
lines parallel to a datum edge or a datum surface.
![Page 76: Ted 111Tools and their Uses](https://reader031.vdocument.in/reader031/viewer/2022021918/58a779e11a28abef478b4623/html5/thumbnails/76.jpg)
Marking Lines Parallel Or Perpendicular The
To Surface Plate
Lecture 5/7
Methods of Marking out
![Page 77: Ted 111Tools and their Uses](https://reader031.vdocument.in/reader031/viewer/2022021918/58a779e11a28abef478b4623/html5/thumbnails/77.jpg)
Marking parallel lines on angled sections
Place the curved leg of the caliper on the
edge of the measuring stick at the zero
mark.
Twist the caliper screw until the pointed
Lecture 5/7
Methods of Marking out
Twist the caliper screw until the pointed
caliper leg reaches the desired
measurement. This measurement will
equal the distance of the scribed line to
the edge of the item marked.
•Place the curved leg of the caliper at
the edge of the item to be marked. Set
the pointed leg of the caliper on the
item's surface.
![Page 78: Ted 111Tools and their Uses](https://reader031.vdocument.in/reader031/viewer/2022021918/58a779e11a28abef478b4623/html5/thumbnails/78.jpg)
Marking parallel lines along shafts or pipes
Lecture 5/7
Methods of Marking out
![Page 79: Ted 111Tools and their Uses](https://reader031.vdocument.in/reader031/viewer/2022021918/58a779e11a28abef478b4623/html5/thumbnails/79.jpg)
7.4Identify datum and describe
7.4Identify datum and describe
methods of marking out
from them.
![Page 80: Ted 111Tools and their Uses](https://reader031.vdocument.in/reader031/viewer/2022021918/58a779e11a28abef478b4623/html5/thumbnails/80.jpg)
Identify datum
The term datum can be described as a point, line or
Datum
Methods of Marking Using Datum
Lecture 5/7
The term datum can be described as a point, line or
edge, depending on the shape of the work piece
from which measurements are taken. The function of
a datum is to establish a reference position
from which all dimensions are taken and hence
all measurements are made.
![Page 81: Ted 111Tools and their Uses](https://reader031.vdocument.in/reader031/viewer/2022021918/58a779e11a28abef478b4623/html5/thumbnails/81.jpg)
Types of datum
• Point datum
Lecture 5/7
Methods of Marking Using Datum
This is a single point from
which dimensions can be
taken when measuring and
marking out. For example,
the centre point of a
pitch circle.
![Page 82: Ted 111Tools and their Uses](https://reader031.vdocument.in/reader031/viewer/2022021918/58a779e11a28abef478b4623/html5/thumbnails/82.jpg)
Types of datum
• Line datum
Lecture 5/7
Methods of Marking Using Datum
• Line datum
This is a single line from which or
along which dimensions are taken
when measuring and marking out.
It is frequently the centre line of asymmetrical component.
![Page 83: Ted 111Tools and their Uses](https://reader031.vdocument.in/reader031/viewer/2022021918/58a779e11a28abef478b4623/html5/thumbnails/83.jpg)
Types of datum
• Edge datum
This is also known as a service
Lecture 5/7
Methods of Marking Using Datum
This is also known as a service
edge. It is a physical surface
from which dimensions can be
taken. These two edges ensure
that the distances marked out
from them are also at right
angles to each other. Datum edges
![Page 84: Ted 111Tools and their Uses](https://reader031.vdocument.in/reader031/viewer/2022021918/58a779e11a28abef478b4623/html5/thumbnails/84.jpg)
Types of datum
• Surface datum
this can be the working surface
Lecture 5/7
Methods of Marking Using Datum
this can be the working surface
of a surface plate or a marking-
out table. It provides a common
datum to support the work and
the measuring and marking-out
equipment.
![Page 85: Ted 111Tools and their Uses](https://reader031.vdocument.in/reader031/viewer/2022021918/58a779e11a28abef478b4623/html5/thumbnails/85.jpg)
Types of datum
• Co-ordinates systems
The distance from a datum to
some feature such as the centre
Lecture 5/7
Methods of Marking Using Datum
some feature such as the centre
of a hole is called an ordinate.
There are two co-ordinates
systems used in common:
1. Rectangular co-ordinates
2. Polar co-ordinates
![Page 86: Ted 111Tools and their Uses](https://reader031.vdocument.in/reader031/viewer/2022021918/58a779e11a28abef478b4623/html5/thumbnails/86.jpg)
Datum
• Uses of datum in Marking out
Figure shows a simple link involving straight lines, arcs,
and circles. It is symmetrical about its centre line. There
Lecture 5/7
Methods of Marking Using Datum
and circles. It is symmetrical about its centre line. There
are several ways of marking out this component. For
the moment a centre line datum will be used.
![Page 87: Ted 111Tools and their Uses](https://reader031.vdocument.in/reader031/viewer/2022021918/58a779e11a28abef478b4623/html5/thumbnails/87.jpg)
• Use of a single edge datum
It assumes that the metal blank from which we are going to
make the link has at least one straight edge.
Lecture 5/7
Methods of Marking Using Datum
![Page 88: Ted 111Tools and their Uses](https://reader031.vdocument.in/reader031/viewer/2022021918/58a779e11a28abef478b4623/html5/thumbnails/88.jpg)
• Use of a point datum
a component that has been drawn using rectangular
co-ordinates and absolute dimensioning for the hole
centers. Each hole centre then becomes a point datum
Lecture 5/7
Methods of Marking Using Datum
centers. Each hole centre then becomes a point datum
for the clusters of small holes.
![Page 89: Ted 111Tools and their Uses](https://reader031.vdocument.in/reader031/viewer/2022021918/58a779e11a28abef478b4623/html5/thumbnails/89.jpg)
• Use of a point datum
This time we will assume that our blank has two datum
edges that are at right angles to each other; they are
mutually perpendicular.
Lecture 5/7
Methods of Marking Using Datum
mutually perpendicular.
![Page 90: Ted 111Tools and their Uses](https://reader031.vdocument.in/reader031/viewer/2022021918/58a779e11a28abef478b4623/html5/thumbnails/90.jpg)
• Use of a point datum
Lecture 5/7
Methods of Marking Using Datum
![Page 91: Ted 111Tools and their Uses](https://reader031.vdocument.in/reader031/viewer/2022021918/58a779e11a28abef478b4623/html5/thumbnails/91.jpg)
7.10 Identify and explain the 7.10 Identify and explain the
main classes of fit.
![Page 92: Ted 111Tools and their Uses](https://reader031.vdocument.in/reader031/viewer/2022021918/58a779e11a28abef478b4623/html5/thumbnails/92.jpg)
Classes of fit
• What is Fit
There are three classes of fit
Lecture 6/7
A. Clearance fit
B. Transition fit
C. Interference fit
![Page 93: Ted 111Tools and their Uses](https://reader031.vdocument.in/reader031/viewer/2022021918/58a779e11a28abef478b4623/html5/thumbnails/93.jpg)
Classes of fit
• A. Clearance fit
In a clearance fit the shaft is always slightly smaller than
the hole.
Lecture 6/7
![Page 94: Ted 111Tools and their Uses](https://reader031.vdocument.in/reader031/viewer/2022021918/58a779e11a28abef478b4623/html5/thumbnails/94.jpg)
Classes of fit
B. Transition fit
A transition fit occurs when the tolerances are so arranged that
under maximum metal conditions (largest shaft: smallest hole).
Lecture 6/7
![Page 95: Ted 111Tools and their Uses](https://reader031.vdocument.in/reader031/viewer/2022021918/58a779e11a28abef478b4623/html5/thumbnails/95.jpg)
Classes of fit
C. Interference fit
In an interference fit the shaft is always slightly larger than the
hole. In a clearance fit the shaft is always slightly smaller than
the hole.
Lecture 6/7
the hole.
![Page 96: Ted 111Tools and their Uses](https://reader031.vdocument.in/reader031/viewer/2022021918/58a779e11a28abef478b4623/html5/thumbnails/96.jpg)
Identify and describe the
operation of tools and 7.6
operation of tools and
equipment for angular
marking out and
measurement.
![Page 97: Ted 111Tools and their Uses](https://reader031.vdocument.in/reader031/viewer/2022021918/58a779e11a28abef478b4623/html5/thumbnails/97.jpg)
Angular marking out and measurement
Measuring angles
Angles are measured in degrees and fractions of a
degree. One degree of arc is 1/360 of a complete
circle. One degree of arc can be subdivided into
Lecture 6/7
circle. One degree of arc can be subdivided into
minutes and seconds. With the introduction of
calculators and computers, decimal fractions of
a degree are also used. However, 1 minute of
arc equals 0.0166666◦
![Page 98: Ted 111Tools and their Uses](https://reader031.vdocument.in/reader031/viewer/2022021918/58a779e11a28abef478b4623/html5/thumbnails/98.jpg)
Angular marking out and measurement
Vernier bevel protractor
The Vernier bevel protractor uses the principle of two
scales, one moving and one fixed. The fixed scale is
graduated in degrees. The moving or Vernier scale is
Lecture 6/7
graduated in degrees. The moving or Vernier scale is
divided into 12 equal parts.
![Page 99: Ted 111Tools and their Uses](https://reader031.vdocument.in/reader031/viewer/2022021918/58a779e11a28abef478b4623/html5/thumbnails/99.jpg)
Angular marking out and measurement
Bevel Gauge
This 3" wide hardened stainless
steel 12" rule with a satin
chrome finish is etched on one
Lecture 6/7
chrome finish is etched on one
side with inch measurements in
1/16" increments on one edge
with center finding markings on
the other edge. The other side
of the rule shows angles from 0°to 50° in clear, distinct 1/4
degree increments.
![Page 100: Ted 111Tools and their Uses](https://reader031.vdocument.in/reader031/viewer/2022021918/58a779e11a28abef478b4623/html5/thumbnails/100.jpg)
Combination Set
A combination set is a tool used for multiple
purposes in metalworking.
Angular marking out and measurement
Lecture 6/7
![Page 101: Ted 111Tools and their Uses](https://reader031.vdocument.in/reader031/viewer/2022021918/58a779e11a28abef478b4623/html5/thumbnails/101.jpg)
Combination set
It is useful for a wide variety of layout and setup
tasks. When used correctly, a fairly high degree of
precision can be achieved.
Angular marking out and measurement
Lecture 6/7
precision can be achieved.
![Page 102: Ted 111Tools and their Uses](https://reader031.vdocument.in/reader031/viewer/2022021918/58a779e11a28abef478b4623/html5/thumbnails/102.jpg)
Combination set
Angular marking out and measurement
Lecture 6/7
![Page 103: Ted 111Tools and their Uses](https://reader031.vdocument.in/reader031/viewer/2022021918/58a779e11a28abef478b4623/html5/thumbnails/103.jpg)
Try square
A tri square is tool used for marking
and measuring a piece of wood.
Lecture 6/7
Angular marking out and measurement
![Page 104: Ted 111Tools and their Uses](https://reader031.vdocument.in/reader031/viewer/2022021918/58a779e11a28abef478b4623/html5/thumbnails/104.jpg)
Try square
Primary use is measuring the accuracy of a
right angle.
Lecture 6/7
Angular marking out and measurement
![Page 105: Ted 111Tools and their Uses](https://reader031.vdocument.in/reader031/viewer/2022021918/58a779e11a28abef478b4623/html5/thumbnails/105.jpg)
7.5Describe how to avoid faults
and minimize inaccuracies 7.5 and minimize inaccuracies
when marking out
![Page 106: Ted 111Tools and their Uses](https://reader031.vdocument.in/reader031/viewer/2022021918/58a779e11a28abef478b4623/html5/thumbnails/106.jpg)
Avoiding faults/inaccuracies
use of appropriate equipment
No matter how accurately measuring equipment is made
and no matter how sensitive it is, one of the most
important factors affecting the accuracy of measurement
Lecture 6/7
important factors affecting the accuracy of measurement
is the skill of the user. The more important procedures for
the correct use of measuring equipment can be
summarized as follows.
![Page 107: Ted 111Tools and their Uses](https://reader031.vdocument.in/reader031/viewer/2022021918/58a779e11a28abef478b4623/html5/thumbnails/107.jpg)
Avoiding faults/inaccuracies
condition of equipment
No matter how accurately measuring equipment is made
and no matter how sensitive it is, one of the most
important factors affecting the accuracy of measurement
Lecture 6/7
important factors affecting the accuracy of measurement
is the skill of the user. The more important procedures for
the correct use of measuring equipment can be
summarized as follows.
![Page 108: Ted 111Tools and their Uses](https://reader031.vdocument.in/reader031/viewer/2022021918/58a779e11a28abef478b4623/html5/thumbnails/108.jpg)
Avoiding faults/inaccuracies
condition of equipment
Lecture 6/7
![Page 109: Ted 111Tools and their Uses](https://reader031.vdocument.in/reader031/viewer/2022021918/58a779e11a28abef478b4623/html5/thumbnails/109.jpg)
Avoiding faults/inaccuracies
condition of equipment
Lecture 6/7
![Page 110: Ted 111Tools and their Uses](https://reader031.vdocument.in/reader031/viewer/2022021918/58a779e11a28abef478b4623/html5/thumbnails/110.jpg)
Avoiding faults/inaccuracies
correct positioning of equipment
No matter how accurately
measuring equipment is made
Lecture 6/7
measuring equipment is made
and no matter how sensitive it
is, one of the most important
factors affecting the accuracy of
measurement is the skill of the
user. The more important
procedures for the correct use of
measuring equipment can be
summarized as follows.
![Page 111: Ted 111Tools and their Uses](https://reader031.vdocument.in/reader031/viewer/2022021918/58a779e11a28abef478b4623/html5/thumbnails/111.jpg)
7.7
Identify and explain the use
of the precision bubble level 7.7 of the precision bubble level
to establish horizontal and
vertical planes
![Page 112: Ted 111Tools and their Uses](https://reader031.vdocument.in/reader031/viewer/2022021918/58a779e11a28abef478b4623/html5/thumbnails/112.jpg)
Precision bubble level
spirit level or bubble level
A spirit level or bubble level is an instrument designed to indicate whether a
surface is horizontal (level) or vertical (plumb).
Lecture 7/7
![Page 113: Ted 111Tools and their Uses](https://reader031.vdocument.in/reader031/viewer/2022021918/58a779e11a28abef478b4623/html5/thumbnails/113.jpg)
7.8Identify and explain the use
of the plumb bob to 7.8 of the plumb bob to
establish vertical planes
![Page 114: Ted 111Tools and their Uses](https://reader031.vdocument.in/reader031/viewer/2022021918/58a779e11a28abef478b4623/html5/thumbnails/114.jpg)
Precision Plumb bob
Plumb bob
A plumb-bob or a plummet is a weight, usually with a
pointed tip on the bottom, that is suspended from a string
and used as a vertical reference line, or plumb-line.
Lecture 7/7
and used as a vertical reference line, or plumb-line.
![Page 115: Ted 111Tools and their Uses](https://reader031.vdocument.in/reader031/viewer/2022021918/58a779e11a28abef478b4623/html5/thumbnails/115.jpg)
use of the precision Plumb bob
Lecture 7/7
![Page 116: Ted 111Tools and their Uses](https://reader031.vdocument.in/reader031/viewer/2022021918/58a779e11a28abef478b4623/html5/thumbnails/116.jpg)
Use of the precision Plumb bob and Spirit level
Lecture 7/7
![Page 117: Ted 111Tools and their Uses](https://reader031.vdocument.in/reader031/viewer/2022021918/58a779e11a28abef478b4623/html5/thumbnails/117.jpg)
7.9Identify template materials
for given situations and 7.9 for given situations and
describe their use.
![Page 118: Ted 111Tools and their Uses](https://reader031.vdocument.in/reader031/viewer/2022021918/58a779e11a28abef478b4623/html5/thumbnails/118.jpg)
Template materials
The use of templates
The use of templates simple components of a
structure do not require to be set out on the
Lecture 7/7
structure do not require to be set out on the
template floor (lofted) but can be marked out
directly from the drawings at the bench in the
fabrication shop. However, even for simple
jobs, templates need to be made where a
number of identical components are required
to ensure uniformity. Let’s now consider some
examples of the use of templates in greater
detail.
![Page 119: Ted 111Tools and their Uses](https://reader031.vdocument.in/reader031/viewer/2022021918/58a779e11a28abef478b4623/html5/thumbnails/119.jpg)
Template materials
Templates for checking
Templates for checking
are made out of metal
Lecture 7/7
are made out of metal
or wood, depending
upon their size and life
expectancy.
![Page 120: Ted 111Tools and their Uses](https://reader031.vdocument.in/reader031/viewer/2022021918/58a779e11a28abef478b4623/html5/thumbnails/120.jpg)
Template materials
Templates for Marking out
Light gauge sheet metal and template-making paper
are the materials most frequently used for making
Lecture 7/7
are the materials most frequently used for making
templates (patterns) for sheet metal fabrications. For
many sheet metal developments it is only necessary to
use part patterns which are aligned with datum lines.
![Page 121: Ted 111Tools and their Uses](https://reader031.vdocument.in/reader031/viewer/2022021918/58a779e11a28abef478b4623/html5/thumbnails/121.jpg)
Template for Marking out
Lecture 7/7
![Page 122: Ted 111Tools and their Uses](https://reader031.vdocument.in/reader031/viewer/2022021918/58a779e11a28abef478b4623/html5/thumbnails/122.jpg)
Radius gauge
Lecture 7/7
![Page 123: Ted 111Tools and their Uses](https://reader031.vdocument.in/reader031/viewer/2022021918/58a779e11a28abef478b4623/html5/thumbnails/123.jpg)
screw cutting centre gauge
Lecture 7/7