terminologies used in welding
TRANSCRIPT
-
8/10/2019 terminologies used in welding
1/25
PRESENTED BY JISHNU.SPRADEEP KUMAR
-
8/10/2019 terminologies used in welding
2/25
Important Terminologies used in Critical WeldingOperation PreheatingPost Heating or DehydrogenationIntermediate Stress leavingInter pass TemperaturePost Weld Heat Treatment Welding Terminologies used in Qualifications Heat In Put
Heat Effected Zone
HAZ Dilution Overlap In Weld Overlay Tempering Bead
-
8/10/2019 terminologies used in welding
3/25
Preheating
Post Heating or DehydrogenationIntermediate Stress leavingInter pass TemperaturePost Weld Heat Treatment
-
8/10/2019 terminologies used in welding
4/25
Heating the base metal along the weld joint to apredetermined minimum temperatureimmediately before starting the weld.
Heating by Oxy fuel flame or electric resistant coilHeating from opposite side of welding whereverpossibleTemperature to be verified by thermo chalks priorto starting the weld
-
8/10/2019 terminologies used in welding
5/25
Preheating eliminates possible cracking of weldand HAZ
Applicable toHardenable low alloy steels of all thicknessCarbon steels of thickness above 25 mm.Restrained welds of all thickness
Preheating temperature vary from 75 C to 200 Cdepending on hardenability of material,thickness & joint restraint
-
8/10/2019 terminologies used in welding
6/25
Preheating promotes slow cooling of weld and HAZSlow cooling softens or prevents hardening of weld
and HAZSoft material not prone to crack even in restrainedcondition
-
8/10/2019 terminologies used in welding
7/25
Raising the pre heating temperature of the weld jointto a predetermined temperature range (250 C to350 C) for a minimum period of time (3 Hrs) beforethe weld cools down to room temperature.
Post heating performed when welding is completedor terminated any time in between.Heating by Oxy fuel flame or electric resistant coilHeating from opposite side of welding whereverpossibleTemperature verified by thermo chalks during theperiod
-
8/10/2019 terminologies used in welding
8/25
Post heating eliminates possible delayed cracking of weldand HAZ Applicable to
Thicker hardenable low alloy steels
Restrained hardenable welds of all thicknessPost heating temperature and duration depends onhardenability of material, thickness & joint restrain
-
8/10/2019 terminologies used in welding
9/25
Hydrogen is intoduced during welding.
Entrapped hydrogen in weld metal induces delayedcracks unless removed before cooling to roomtemperature
Retaining the weld at a higher temperature for a longerduration allows the hydrogen to come out of weld
-
8/10/2019 terminologies used in welding
10/25
Heat treating a subassembly in a furnace to apredetermined cycle immediately on completion of criticalrestrained weld joint / joints without allowing the welds togo down the pre heat temperature. Rate of heating,Soaking temperature, Soaking time and rate of coolingdepends on material quality and thickness Applicable to
Highly restrained air hardenable material
-
8/10/2019 terminologies used in welding
11/25
Restrained welds in air hardenable steel highly prone tocrack on cooling to room temperature.
Cracks due to entrapped hydrogen and built in stress
Intermediate stress relieving relieves built in stresses
and entrapped hydrogen making the joint free fromcrack prone
-
8/10/2019 terminologies used in welding
12/25
The temperature of a previously layed weld beadimmediately before depositing the next bead over itTemperature to be verified by thermo chalk prior to
starting next bead Applicable to
Stainless SteelCarbon Steel & LAS with minimum impact
-
8/10/2019 terminologies used in welding
13/25
Control on inter pass temperature avoids over heating,there by
Refines the weld metal with fine grainsImproves the notch toughness propertiesMinimize the loss of alloying elements in weldsReduces the distortion
-
8/10/2019 terminologies used in welding
14/25
Heat treating an assembly on completion of all applicable welding, in an enclosed furnace with controlledheating/cooling rate and soaking at a specific temperaturefor a specific time. Rate of heating, Soaking temperature, Soaking time andrate of cooling depends on material quality and thickness Applicable to
All type of CS & LAS
-
8/10/2019 terminologies used in welding
15/25
Welded joints retain internal stresses within the structureHAZ of welds remains invariably hardenedPost Weld Heat Treatment relieves internal stresses andsoftens HAZ. This reduces the cracking tendency of theequipment in service
-
8/10/2019 terminologies used in welding
16/25
Heat In Put
Heat Effected Zone HAZ Dilution Overlap In Weld Overlay Tempering Bead
-
8/10/2019 terminologies used in welding
17/25
It is a part and parcel of weld joint It is inevitable It has properties different from BM & Weld Metal
Weld Zone
HAZDiluted BM
Diluted BM
Weld Zone
Fusion Line
-
8/10/2019 terminologies used in welding
18/25
In all Fusion welding, a small portion of BM very close to the welding heat gets melted andadded to weld zone / fusion zone. Dilution isthe ratio of molten base metal volume (Area)to the volume ( Area) of total fusion zone
HAZ
Diluted BM
Weld / Fusion Zone
Fusion Line
% Dilution = (Area of Diluted BM Total Fused Area) 100
-
8/10/2019 terminologies used in welding
19/25
Weld metal chemistry changes depending on
the extent of dilution Chemical elements influence Physical
properties of the joint. Weld chemistry influences corrosion
resistance of weld overlays
Weld Zone
HAZDiluted BM
Diluted BM
Weld Zone
Fusion Line
-
8/10/2019 terminologies used in welding
20/25
The extent of covering or over lapping of previous weldbead by the adjacent bead.
40 to 50 % Over Lap 10 to 15 % Over Lap
Less Dilution More DilutionMore Thickness
Less Thickness
-
8/10/2019 terminologies used in welding
21/25
Overlap of 40 to 50% results in Less Dilution & more weldoverlay Thickness per layerLess dilution results weld metal chemistry more towardsfiller metal chemistry
40 to 50 % Over Lap 10 to 15 % Over Lap
Less Dilution More DilutionMore Thickness
Less Thickness
-
8/10/2019 terminologies used in welding
22/25
In a multi pass groove & Fillet Welds, each bead & itsHAZ are getting tempered (heat treated) by the welding heat of the next bead.
Thus all beads & their HAZ, except those in last layer ,are tempered.Temper beads are the specially & carefully weldedtemporary beads on the top of final weld
reinforcement with out allowing to generate any HAZ within the BM. Temper beads are to be ground flush with the required reinforcement.
-
8/10/2019 terminologies used in welding
23/25
Temper Bead T1 & T2 Not To Generate HAZ In BMTemper Beads To Be Ground Flush
T2T1
21
33
4 455
T1 & T2 To be ground Flush
HAZ
Rqd. Reinforcement
-
8/10/2019 terminologies used in welding
24/25
-
8/10/2019 terminologies used in welding
25/25