the benchmark - soudronic-berufsbildung.ch · such as triple and quadruple necking allow for...
TRANSCRIPT
S O U D R O N I C M E T A L P A C K A G I N G S Y S T E M S
Soudronic AG
Industriestrasse 35
CH-8962 Bergdietikon
Phone + 41 44 743 66 66
Fax + 41 44 743 66 99
WWW.SOUDRONIC.COM
T ECHNO LOG Y T HAT K E E P S YO U A H EAD
THE
BENCHMARKIN METAL PACKAGING
PRODUCTION SYSTEMS
A STRONG COMMITMENT TO OUR CUSTOMERSAND SUPERIOR TECHNOLOGY.
SOUDRONIC IS THEWORLD’S LEADINGSUPPLIER OFCOMPLETE METALPACKAGING SYSTEMS.
Metal cans are produced in a broad variety of shapes and sizes and used for
every imaginable kind of food, aerosols and beverage. Because of the out-
standing properties of metal packaging, cans, pails, drums or even
irregularly shaped containers are often the packaging of choice for industrial
and technical goods such as lubricants, paints, lacquers and aerosols.
Although the production process is identical to food and beverage cans, the
forming, shaping, endmaking and testing of industrial packaging requires
specialist expertise.
ECONOMICS THAT MAKE SENSE . Tinplate cans are airtight, taste-neu-
tral, safe and easy to store and transport, diffusion-proof and fire-resistant.
Production is cost-efficient and saves energy and time. Thanks to the mag-
netic properties of the raw material, tinplate cans are easily recycled on an
industrial scale. Worldwide, in fact, steel is one of the most recycled mate-
rials of them all. Even when not recycled, the material corrodes completely
and naturally without harm to the environment.
Since materials account for about two-thirds of total production cost,
savings are best achieved by reducing the amount of material required to
an absolute minimum. New technologies now permit the production of
three-piece cans using sheet grades as thin as 0.10 mm, and forming methods
such as triple and quadruple necking allow for maximum tightness and
stability with minimal material requirements. With leading-edge production
lines, reject rates remain well below one percent.
METAL – A MODERN, VERSATILEPACKAGING MATERIAL .
We develop, build and install superior resistance welding solutions for a variety
of applications specific to the METAL PACKAGING INDUSTRY. Our range
includes single components as well as all-in turnkey manufacturing systems.
Founded in 1953, Soudronic’s headquarters are located in Bergdietikon
near Zurich. Today, the company employs a staff of more than 600 people in its
development and production facilities all over the world. The company’s sales and
service network covers more than 120 countries, reflecting a large and globally
diverse customer base. Thanks to a sound financial basis, Soudronic has remained
independent throughout a history going back more than 60 years.
UNDERSTANDING OUR CUSTOMERS’ NEEDS . The highest engineering
standards, long-lasting quality and maximum system efficiency are the basis of our
excellent worldwide reputation. By investing a high percentage of our annual rev-
enues in research, development and the continuous improvement of our products,
we ensure that our systems always represent the state-of-the-art in technology.
An impressive number of long-term patents testify to our high innovation rate.
The technology and quality of our products are always important, of
course, but the needs of our customers must always remain paramount. Most of
them are looking for maximum efficiency and flexibility, user-friendliness and com-
mitted after-sales service. The industry they operate in is stiffly competitive and to
prosper they need to increase productivity while reducing reject rates and scrap
material to a minimum. They often have to react quickly to changing market
demands and need to rely on a flexible production infrastructure. Our ability to
provide metal packaging specialists with solutions tailor-made to their exact needs
has made us the natural partner for of an increasing number of customers.
3G R O U P O V E R V I EW2 G R O U P O V E R V I EW
5G R O U P O V E R V I EW4 G R O U P O V E R V I EW
SOUDRONIC IN SWITZERLAND. Located in Bergdietikon near Zurich, Soudronic
in Switzerland is the industry’s premier source for canbody welders, seam
protection and curing systems, peel-off solutions and two-piece canmaking
machines. Our engi neers also design complete canbody production lines
according to customer require ments. Thanks to our large assembly facilities, we
are able to subject complete systems to thorough testing before shipment. Since
its foundation over 60 years ago, our company has produced and installed more
than 6000 canbody and drum welders.
CEPAK IN ITALY. Cepak is a recognized high-quality manufacturer. The company
has so far sold more than 800 systems. Most of our low- and medium-speed
canbody production lines feature slitters from Cepak.
OCSAM IN ITALY. Ocsam is the leading manufacturer of high-capacity slitters
and transfer systems. The company’s reference list comprises more than 800
installations. Our high-speed manufacturing lines for three-piece cans typically
include slitters and transfer systems from Ocsam.
SABATIER IN FRANCE. Sabatier is one of the world’s premier suppliers of complete
production systems for industrial packaging. The company produces stand-alone
machines and acts as general contractor for large customized turnkey projects.
CANTEC IN GERMANY. Cantec’s core business is the development and production
of bodyformers, high-performance systems for ends, caps and easy-open shells
as well as the supply of complete endmaking lines, including process know-how
and services.
SOUDRONIC IN CHINA. Since 1995 a group member, Soudronic (Guangzhou) Ltd.
is responsible for the Chinese market. Low-speed welders for the local market are
assembled and tested at the production facility in Guangzhou.
SOUDRONIC LTD. The US-based affiliate of the Soudronic Group has been estab-
lished in 1974. The company acts as Soudronic's North-American sales and service
representation and provides state-of-the-art sales support and after sales services.
SOUDRONIC MEXICANA. Based in Mexico and established in 1991, Soudronic
Mexicana is responsible for sales and after-sales services in the Latin-American region.
SOUDRONIC SOUTH EAST ASIA. Founded in 1988 and based in Singapore,
Soudronic South East Asia takes care of the sales and after-sales activities in the
following markets: Singapore, Malaysia, Indonesia.
THE FOLLOWING GROUP COMPANIES REPRESENT THE INDUSTRIAL CORE OF SOUDRONIC’S METAL PACKAGINGOPERATIONS .
A KEY PLAYER IN THE METAL PACKING INDUSTRY.
We provide a complete range of machines and components – including slitters,
transfer systems, welding machines, seam protection systems, bodyformers, two-
piece can production lines and endmaking systems – to meet the requirements
of any manufacturing line for cans, pails, drums and irregularly shaped containers.
Today, with more than 15 000 machines and system components installed, our
production systems can be found virtually all over the world and cover the entire
manufacturing process from the lowest to the highest production speed and from
the smallest to the largest size.
Deciding to work with Soudronic often marks the start of a lifelong rela-
tionship. Apart from stocking a complete range of spare parts for every piece of
machinery we have ever produced, we regularly retrofit existing systems with the
latest technology, boosting our customers’ productivity and ensuring they remain
competitive for many years to come.
F O R M I N G
T I N P L AT E
B L A N K S I N T O
C A N B O D I E S
73 - P I E C E C A N M A N U F A C T U R I N G6 3 - P I E C E C A N M A N U F A C T U R I N G
SOUDRONIC DESIGNS, BUILDS, INSTALLS ANDMAINTAINS FULLY INTEGRATED MANUFACTURINGLINES WITH PRODUCTION SPEEDS OF UP TO1200 CANBODIES PER MINUTE.
A typical canbody production system consists of the following components: a slitter
to cut the tinplate base material into body blanks of the required size, a transfer
system, a canbody welder, a seam protection unit, a curing system to dry and
harden the seam protection and a bodyformer to give the canbody its final profile
and shape. The line will also include a unit to test the air-tightness of the finished
product and a palletizer.
A single control system, equipped with a touchscreen panel, permits
central operation and management of the entire production line.
COMPLETE PRODUCTION LINESFOR EVERY NEED.
CANBODY WELDER
CURING SYSTEM
SEAM PROTECTION SYSTEM
BODYFORMER
TRANSFER SYSTEM
SLITTER
PALLETIZER
TESTER
3-PIECE CANS.
P R O T E C T I N G T H E
W E L D S E A M
C U T T I N G M E TA L S H E E T S
I N T O B O D Y B L A N K S
H E AT- D R Y I N G T H E S E A M
P R O T E C T I O N L AY E R
The slitter is the first stage in a three-piece canbody production line. It cuts the
printed and lacquered base material – large square metal sheets – into body blanks
of the required size. The cut blanks are then fed into the canbody welder’s mag-
azine from the slitter by a transfer system, which is indispensable in any fully
automatic production line.
Soudronic slitters and transfer systems, built by our subsidiaries Cepak
and Ocsam, easily satisfy demanding quality criteria such as versatility, precision,
reliability, fast, simple adjustability and production speed.
The heart of a three-piece can production line is the canbody welder. This is where
the body blanks receive their cylindrical shape and where the seam overlap is
welded. The Superwima welding principle, developed by Soudronic, requires a
minimal overlap of as little as 0.40 mm. Optimal control of the welding current in
combination with an accurate pressure on the overlap guarantee a mashed seam
of only 1.4 times the thickness of the sheet metal.
After the canbody has been welded, a physical barrier against oxidation and other
chemical reactions is applied to the inner and outer weld seams. Whether for rel-
atively slow pail manufacture or high-speed tinplate can production, we offer an
impressive range of fully automated systems for powder-coating or liquid-lacquer-
ing of the inside seam, and roller or brush-lacquering of the outside seam.
After passing through the weld seam protection unit, the canbody enters the
curing system. A conveyor belt takes the canbodies through a gas-fired heating
system with automatically regulated hot air burners. The conveyor belt has guides
that ensure the canbodies remain centrally positioned throughout the entire heat
treatment. Soudronic has developed a modular range of curing systems, avail-
able in varying lengths, to accommodate any production speed.
SLITTERS AND TRANSFER SYSTEMS .
93 - P I E C E C A N M A N U F A C T U R I N G8 3 - P I E C E C A N M A N U F A C T U R I N G
SEAM PROTECTIONUNITS .
CURING SYSTEM .
CANBODY WELDERS .
W E L D I N G A M A S H E D
C A N B O D Y S E A M
I N C O M M A N D
O F A C O M P L E X
M A N U FA C T U R I N G
P R O C E S S
S E A M I N G
T H E C A N B O D YOnce the raw canbodies leave the curing system, they are ready to be given
their final shape and prepared for the endseaming process. Our highly flex-
ible, fully automated bodyformers combine all the necessary functions in
a single machine: shaping (mainly for optical purposes), necking (for good
stacking properties after filling), flanging (necessary for the subsequent
seaming process), beading (for additional stability) and seaming (of either
the bottom or top end). Cantec’s bodyformers are a mature multi-function
system designed to meet the technical and commercial canmaking
challenges of the future.
With the Soudronic UNICONTROL operating system, an entire canbody
production line can be operated from a single touchscreen panel. The easy-
to-handle, Windows-based system guides the operator through the process
using a simple graphical user interface, thus reducing instruction time and
enabling training on the job. Standardized, reproducible settings, predefined
values and checklists guarantee highly efficient production cycles. The
system provides guidance and support in several languages and permits
simulations on standard PC monitors in order to facilitate training setups
for machine operators.
UNICONTROL provides plant management with production statistics
and other relevant data, and can be linked to ERP systems.
INTEGRATED LINECONTROL .
BODYFORMERS .
113 - P I E C E C A N M A N U F A C T U R I N G10 3 - P I E C E C A N M A N U F A C T U R I N G
2-PIECE CANS.
EXIT CONVEYORCONVEYOR
SHEET FEED PREDRAW PRESS
SHEET FEED REDRAW/TRIMMING
PRESS
SHEET FEEDER
132 - P I E C E C A N M A N U F A C T U R I N G
Developed and manufactured at Soudronic headquarters in Switzerland, our deep-
drawing press systems are designed to stamp, predraw, final draw, emboss, panel
and trim two-piece cans in a vast range of shapes and sizes to suit any need or appli-
cation, at a maximum speed of 600 cans per minute. Finished cans are ejected onto
an outfeed conveyor that transports them to a packaging table or palletizer.
Typically, a sheet feed multi-die press line for the production of deep-drawn
cans will consist of a sheet-feed press, which predraws the canbodies. The pre-
drawn bodies are then transported to the redraw, paneling and trimming press,
where the can’s final shape is drawn.
A FULL RANGE OF DEEP-DRAWNCAN AND MULTI-DIE SYSTEMS.
12 2 - P I E C E C A N M A N U F A C T U R I N G
WE BUILD AND INSTALL PRODUCTION L INESFOR DEEP-DRAWN CANBODIES WITH ROUND,CONICAL, RECTANGULAR OR IRREGULARSHAPES AS WELL AS MULTI -D IE PRESSESCAPABLE OF STAMPING AND FORMING UP TO E IGHT CANS IN ONE STROKE.
152 - P I E C E C A N M A N U F A C T U R I N G
The manufacture of two-piece canbodies places considerable stresses and strains
on the material. To keep these within acceptable limits, bodies are generally made
in two stages. In the first of these, the predraw press punches the blank into a
basic, but as yet not final, cup shape. Soudronic’s predraw press is able to form
four two-piece shells in a single stroke. The predrawn cans now move from the
press onto a conveyor that takes them to the next stage.
At the redraw stage, the canbody is pressed into its final form, reducing the dia -
meter and building up the sidewall of the can to accommodate a predefined con-
tent volume. At the same time, the bottom of the can is paneled to give it extra
strength, any excess tinplate removed and the top curled, necked and flanged as
necessary. Throughout the pre and redraw phases, cans are moving at such high
speed that manual control is impossible. Soudronic multi-die lines can therefore
be equipped with a video monitoring and inspection system as an optional extra.
SHEET FEED PRESS:PREDRAW .
14 2 - P I E C E C A N M A N U F A C T U R I N G
SHEET FEED PRESS:REDRAW ANDTRIMMING .
P R E F O R M I N G O F
T W O - P I E C E S H E L L S
F I N A L F O R M I N G
A N D T R I M M I N G
O F C A N S
DRYER
STACKER
CURLER
17E N DM A K I N G S Y S T EM S16 E N DM A K I N G S Y S T EM S
SOUDRONIC'S ENDMAKING SYSTEMS, PRODUCEDBY CANTEC IN GERMANY, USE STATE-OF-THE-ARTTECHNOLOGIES TO GIVE YOU UNMATCHEDEFFICIENCY AND FLEXIBILITY WHILE KEEPINGYOUR PRODUCTION COSTS COMPETITIVE.
Whether you need conventional ends or technically demanding peel-off lids, we
supply turnkey solutions for both medium and high-speed applications.
For high-speed endmaking, we use multi-die presses reaching output
capacities of up to 4000 ends per minute. The curlers, liners, ovens and packing
systems are all designed to match the output of the highly productive presses. The
unique tooling systems of Cantec offers optimized end designs for downgauging
of tinplate and thus saving production costs.
Typical medium-speed endmaking systems consist of a scroll shear to cut
the base material into scrolled strips, a strip feed press, a curler, a compound
lining system, a drying oven and a packing system.
Our endmaking lines can be centrally operated by a single control system
with a touchscreen panel. High-speed lines can also be equipped with video
inspection and control systems.
HIGH-QUALITY ENDS INALL SHAPES AND SIZES .
MULTI-DIE PRESS
SHEET FEEDER
LINER
INSPECTION
ENDMAKING SYSTEMS.
19E N DM A K I N G S Y S T EM S
Cantec’s multi-die press END-O-MAT is a high-performance multi-die production
system for lids, easy open shells, rings, bottom ends and twist-off caps. Designed
to meet the technical and commercial endmaking challenges of the future, this
single-line system makes up to 4000 ends per minute (depending on diameter),
all of uniformly high quality. It handles any type of material and minimizes scrap.
Whether the ends you are manufacturing are round or irregular, fully or partially
opening, or made of steel or aluminum, the quality of the final product depends
entirely on the press.
Thanks to their rigid frame construction, our strip-feed presses work to an
extremely high level of precision and require very little maintenance. They stamp
and form lids and bottom ends for two and three-piece cans as well as pails.
MULTI-DIE PRESSESFOR HIGH-SPEEDENDMAKING .
18 E N DM A K I N G S Y S T EM S
D I S C - C U R L E R
T R A N S F E R R I N G E N D S
F R O M T H E C U R L I N G
S TAT I O N T O T H E
C O M P O U N D L I N E R
T O O L I N G O F E N D - O - M AT
M U LT I - D I E P R E S S
STRIP-FEED PRESSESFOR MEDIUM-SPEEDENDMAKING .
21P E E L - O F F E N DM A K I N G S Y S T EM S
We developed peel-off ends for two and three-piece cans as a user-friendly
alternative to easy-open ends. Peel-offs are suitable for dry, retortable and hot-
filled products, do not spill or splash and are easily opened without additional tools
or damage to fingers. The high-speed UNISEAL heat-sealing system integrates
seamlessly with existing can production lines and allows for brand name
embossing on the outside surface together with a virtually unlimited choice of
shapes and tabs as well as different curls for different types of products. It comes
with a ring-forming module and produces up to 800 composite or aluminum peel-
off ends per minute in a single pass without the need for restacking.
PEEL-OFF ENDS OPEN UP NEW DIMENSIONS IN CONSUMER-FRIENDLINESS.
20 P E E L - O F F E N DM A K I N G S Y S T EM S
A CONVENIENT ALTERNATIVE TO CONVENTIONALENDS, PEEL-OFF LIDS ARE INCREASINGLY INDEMAND. OUR HEAT-SEALING ENDMAKING COM-PONENTS ALLOW METAL PACKAGING PRODUCERSTO SATISFY MARKET DEMAND WITHOUT THENEED FOR MASSIVE INVESTMENT.
DESTACKING
PUNCHING
DRAWING
TURNING
SEALING
FOIL PUNCHINGPRE-SEALING
EMBOSSING
OPTION: OVER-HEAD CONVEYOR
CURLINGPEEL-OFF ENDS.
23P E E L - O F F E N DM A K I N G S Y S T EM S22 P E E L - O F F E N DM A K I N G S Y S T EM S
E N D I N F E E D U N I T
H I G H - S P E E D
T R A N S P O R T O F
P E E L - O F F E N D S
Ends enter the heat-sealing machine top downward and are destacked before moving
onto the punching station, where the middle part is punched out to leave the can
opening. At the next stage, the cut edge is drawn downward and, if desired, formed
into an ‘R’ curl. At this point, the rings are fed into the Soudronic sealing system.
The range of end forms produced by our heat-sealing systems is practi-
cally un limited and includes standard round ends, flattened openings (D-shape,
spoon leveling holes) and drinking holes, and even runs to the shape of the tab
(flat tabs, ring-pull tabs with finger hole).
As the rings enter the second part of the system, they are turned through 180° to
face the right way up. The dies that punch out the foil are aligned to produce the
maximum number of ends from the foil material, considerably reducing material
costs. The membrane then goes through a two-stage sealing process: first,
presealing, which fixes the foil in place, and then the final sealing stage. This is a
much more advanced process than older, more conventional methods and
significantly increases the quality of the seal.
As an alternative to aluminum foil, the composite multilayer foil may
consist of different layers designed for various types of packaging and contents.
Multilayer foil is flexible and extremely tough and withstands impacts better than
aluminum alone. Additionally it can be printed using any of several methods
(digital, gravure or flexoprint).
As an additional application we also provide a tab-fixing unit for use with
one to four lines. This applies the adhesive that is used to fix the tab to the end.
FORMING THE RINGS .
SEALING THINGS UP .
E N D S A N D R I N G S W I T H
D - S H A P E S P O O N L E V E L I N G
A N D R I N G - P U L L O P E N I N G
EXPANDER
DRYING OVEN
CURLING/BEADINGSTATION
NECKING/FLANGING/SEAMINGSTATION
EAR-WELDING/ BAIL PLACING
STATION
STACKER
WELDER
TESTER
25I N D U S T R I A L PA C K A G I N G L I N E S
UNMATCHED FLEXIBILITYGUARANTEED BY MODULAR SYSTEM CONCEPT.
24 I N D U S T R I A L PA C K A G I N G L I N E S
INDUSTRIAL PACKAGING.
PRODUCTION L INES FROM SABATIER MANU-FACTURE SAFE, STABLE PACKAGING FORINDUSTRIAL, TECHNICAL AND EDIBLE GOODS.
The outstanding properties of metal packaging materials make them ideal for a
vast range of industrial and technical products as well as edible oils and other
foods. Metal containers such as pails, drums or cans of various shapes and sizes
are air and water-tight, fire-resistant and can be transported safely and stored for
extended periods of time.
Within the Soudronic Group, Sabatier in Vitrolles (France) designs and
manufactures a comprehensive range of modular, compact and flexible assembly
lines for industrial metal packaging. Thanks to our highly specialized know-how, we
provide packaging solutions for cylindrical, conical, rectangular, oblong or square
metal containers, including the necessary endmaking systems and leak testing units.
27I N D U S T R I A L PA C K A G I N G L I N E S
For the production of round cans in sizes ranging from 0.2 to 70 liters or drums of
up to 200 liters, our Bodypack assembly line provides the ideal solution. The name
Bodypack stands for compact, flexible modular assembly lines incorporating the
very latest technologies. In tandem with our canbody or drum welders and seam
protection units, they are capable of performing all the operations required for the
production of tapered or cylindrical canbodies, including body expansion, shaping,
flanging and beading. Bodypack lines are also capable of seam-assembling bottom
and top ends or mounting lids and handles. Supplementary machines and func-
tionalities can easily be added to any Bodypack line.
Squarepack is a compact, modular system family for the assembly of irregularly
shaped cans ranging in capacities from 0.2 to 20 liters. The assembly lines are
highly flexible and typically consist of a stretch former and a can erector together
with two squeeze flangers and two seamers. The system integrates easily with
our welding machines and seam protection units.
Whether you produce rectangular, square, oval or oblong containers,
Squarepack assembly lines provide convincing answers to an exceptional variety
of packaging needs. Depending on the size and design of the packaging, paneling
machines and leak testing units can easily be added to the lines.
We offer a wide choice of proven and efficient solutions, ranging from con -
ventional ends to easy-open technologies, specially designed for endmaking with
industrial packaging. Our curling-lining and handle-welding machines for round,
square or oblong ends and lids ensure that metal containers can be closed tightly
and transported safely.
We provide a broad range of customized solutions for unique requirements. The
list of special machines, tools and components for individual customer needs is
almost endless. For the manufacturing of specially designed cans, for instance,
we have developed high-performance vertical body shapers that integrate perfectly
with existing assembly lines. Or we offer a range of atmospheric closing machines
for the rectangular cans used with fish, meat and processed food.
MODULARCYLINDRICALPACKAGINGSOLUTIONS .
ASSEMBLY LINESFOR IRREGULARLYSHAPED CANS .
FORMINGIRREGULARLYSHAPEDCANBODIES .
26 I N D U S T R I A L PA C K A G I N G L I N E S
W E L D I N G T H E E A R
T O T H E C A N B O D Y
T H E S H A P I N G A N D
F O R M I N G O F C A N B O D I E S
I S A S T E P - B Y- S T E P
P R O C E S S
F O R M I N G I R R E G U L A R LY
S H A P E D C A N B O D I E S
TAILOR-MADE METAL PACKAGING .
Our main priority is to keep our customers happy. Happy that they have purchased
a solution which suits their needs precisely; and happy because they can rely on
our support, no matter what happens.
We advise our customers which spare parts – particularly those subject to
wear and tear – they should store on site to avoid costly downtime. We provide
on-site support during commissioning and production start-up. We conduct training
seminars for the operating staff. And we stay prepared, just in case our help is
needed one day.
Thanks to a global after-sales service network, our technicians and specialists
can be available on any customer site at short notice. Customer support as we
understand it is not only a global but also a lifelong commitment.
Our global after-sales service organization takes care of preventive maintenance
and regular inspections of your production machinery. A telephone troubleshoot-
ing service provides rapid support and solves many problems quickly and efficiently.
We maintain a database containing full technical specifications and records
of every machine and production line ever installed. This enables us to react to
requests for spare parts promptly and professionally.
At our central store in Switzerland, we keep a comprehensive stock of more
than 30 000 genuine spare parts ready for immediate dispatch. Thanks to a world-
wide distribution network, we can guarantee ultra-fast delivery – in most cases
within 24 hours. With our team of experienced spare parts specialists, we make
sure that the maintenance and repair of our machines is carried out in a matter of
hours, not days.
FAST, RELIABLE CUSTOMER SUPPORT WORLDWIDE.
PROFESSIONALMAINTENANCE ANDRELIABLE SPAREPART SUPPLY.
29A F T E R - S A L E S S E R V I C E28 A F T E R - S A L E S S E R V I C E
AFTER-SALES SERVICE.
SOUDRONIC’S CUSTOMER SERVICESTARTS LONG BEFOREAN ORDER IS PLACEDAND GOES ON LONGAFTER DELIVERY ANDINSTALLATION.
Q U A L I T Y S PA R E PA R T S
R E A D Y F O R U LT R A - F A S T
D E L I V E R Y
P R O F E S S I O N A L O N -
S I T E I N S T R U C T I O N
F O R M A C H I N E
O P E R AT O R S
A P P LY I N G H I G H E S T
S TA N D A R D S T O
M A C H I N E O V E R H A U L S
31S O U D R O N I C A N D S U S TA I N A B I L I T Y
Soudronic has focused increasingly on ecological issues and the benefits of
smart metal packaging. Metal is, quite simply, one of the most economical,
environment-friendly and hence sustainable forms of packaging available to
manufacturers today. And the arguments in its favour are compelling.
First and foremost is the fact that metal cans today require far less raw
material than in the past. Soudronic leads the way in the development of the
advanced canmaking machines needed to work with downgauged tinplate,
i.e. sheet metal stock of as little as 0.01 mm in thickness. Lighter cans mean
more containers per ton of tinplate, savings on natural resources and, over-
all, a significant reduction in the world’s carbon emissions footprint.
Apart from the technological advances that make metal packaging so
attractive, steel has countless advantages that put it in
an environmental class of its own.
At Soudronic, we believe the canmaking
industry has a responsibility to enlighten
consumers about the largely unperceived
ecological benefits of our products. If
this helps to change consumer per-
ceptions about metal packaging – and
push up recycling rates still further
– we will already have taken a major
step forward.
SOUDRONIC AND THE SUSTAINABILITY ISSUE OR WHY TINPLATE RULES.
SMALL FOOTPRINT.BIG STEP FORWARD .
Thanks to their outstanding quality and precision engineering, our canbody welders
will last virtually forever if properly maintained. However, producers need to be
aware that older models are much less efficient than today’s generation of canbody
welding machines. With tried-and-tested standardized solutions for the conver-
sion and retrofit of older machines, we offer our customers the opportunity both
to increase the performance and to improve the cost-effectiveness of their canbody
production line at a reasonable cost.
Depending on the customer’s needs, we carry out complete machine
overhauls, upgrades and conversions either on site or at our own facilities.
A well-maintained second-hand machine can be the ideal solution for an urgent
customer need. Often, customers who upgrade their production lines with our lat-
est machines ask us to help them re-sell the equipment they are replacing.
Thanks to the long-lasting quality of our products, it is absolutely no prob-
lem to overhaul and retrofit such equipment. Customers can rest assured that any
second-hand machine they buy from us is in superb working condition and, given
correct maintenance, will go on performing indefinitely.
Even the most sophisticated production line can only deliver satisfactory results
if the operating personnel have been carefully trained. This is why we offer train-
ing programs individually tailored to either specific machines or entire production
lines. Our aim is to ensure that all participants are able to operate and maintain
our machines safely, efficiently and economically.
Training courses and seminars can be held at one of our training centers
in Switzerland, France, Germany, Italy, Mexico, Singapore, the USA and China, or
on the customer’s own premises. Participants receive comprehensive personal
documentation with step-by-step instructions and manuals.
BOOSTING THEPERFORMANCE OFOLDER CANBODYWELDERS .
A HEALTHY MARKETFOR SECOND-HANDMACHINES .
CUSTOMIZEDTRAINING ANDINSTRUCTION .
30 A F T E R - S A L E S S E R V I C E