the complete range of textured coatings, from kansai paint. · • friable and powdery surfaces...

The complete range of textured coatings, from Kansai Paint.

.

Texture

Texture

Sometimes surface preparation may be difficult or expensive due to irregularities in the painting surface or hard to reach areas. Paint’s with low dry film thickness cannot be used under these circumstances.

Ensuring that the finished surface remains the same for years to come can also be challenging unless the right product is selected. Exposure to exterior climates where high erosion or moisture accumulation is common can also affect the final look of a building over time.

Kansai offers textured products with easy application for interiors and exteriors to answer this need. Our products offer varying dry film thickness levels to hide surface irregularities without the need for additional coats of stucco, and can be applied easily with spray guns in difficult to reach areas.

See the table below to select which product is right for you.

Where to useWALLS EPOXY

TEXTUREDECORETEXTURE

SPRAYTEXTURE

HERITAGE TEXTURE

FINECOAT

STONEFINISH

ACRYLICTEXTURE

ACCENT, TRIM & ACCESSORIES

ROOFS

Family Room

Doors & Windows

Roof

Bedroom

Cabinets

Kitchen & Bathroom

Shutters

Living room & Dining Room

Trim

Hallways

Ceiling

Kid’s Room

Interior Furniture

Exterior & Boundary Walls

-

l

-

-

l

l

l

-

-

-

-

-

-

l

-

-

-

-

-

-

-

-

-

-

-

-

- -

-

-

-

-

-

-

l

-

l

-

-

-

-

l

-

-

-

-

-

-

-

-

-

-

-

-

- -

-

-

-

-

-

-

l

-

l

-

-

-

-

l

-

-

-

-

-

-

-

-

-

-

-

-

- -

-

-

-

-

-

-

l

-

-

-

-

-

-

-

Texture

TEXTURE

Kansai Stone Finish• Attractive natural stone finish.• Water based coating.• Tough and durable finish provides

excellent weather resistance.

Kansai Decor Texture• A water-based acrylic copolymer

textured coating for exterior use.• High build textured paint which helps

produce a variety of patterns depend-ing on application technique.

• Covers undulation and unevenness present in the surface.

Kansai Heritage Texture• A premium quality water based

textured coating for protecting and decorating exterior walls.

• Provides an excellent antique effect that gives the wall an aged look.

• High build texture with elastomeric properties.

Texture

TEXTURE

Kansai Fine Coat• Provides good opacity and scrub

resistance.• Odorless and Solvent free.• Provides good weather resistance.• Easy to apply.

Kansai Acrylic Texture• Provides exceptional exterior durability.• water-based coating with a fine texture

for decorating and protecting exterior and interior walls.

Texture

TEXTURE

Kansai Spray Texture• Provides exceptional exterior durability.• Solvent free and environmentally

friendly.• Provides good adhesion properties for

further topcoats.

Kansai Epoxy Texture• Provides excellent adhesion to

substrate.• Can be over coated with a range of

Kansai Epoxy and Polyurethane top coats

PRODUCT CODE: DATASHEET NO: ISSUE DATE: A-422 KPME-B-09 MARCH 2014

kansai acrylic texture

PRODUCT DESCRIPTION KANSAI ACRYLIC TEXTURE is an extremely durable, water-based coating with a fine texture for decorating and protecting exterior and interior walls.

INTENDED USAGE • To protect exterior and interior wall surfaces.• To bridge and fill fine hairline cracks on exterior cement plastered walls• Suitable for application to suitably primed cement plaster, concrete and brickwork.

FEATURES & BENEFITS • Provides exceptional exterior durability.

PHYSICAL PROPERTIES Appearance Matte

Colours White and range of standard colours.

Tint Bases N.A

Generic Type Pure Acrylic

Volume Solids Approx. 47%

Specific Gravity at 23oC 1.4 (approx.)

Recommended DFT per coat Min: 80 μm Max: 90 μm

Flash Point N.A.

Theoretical Spreading Rate 6 m2/litre @ 85 μm DFT

APPLICATION DETAILS Mixing Stir thoroughly with a flat paddle until homogeneous and stir periodically during use.

Substrate Thoroughly prepared concrete, plaster, brickwork and various building boards.

Method Roller.

Thinning Ready for use by roller or spray application.

Cleaning Water

Application Environment

Surface Temperature

Ambient Temperature

Relative Humidity

Min 10 °C 10 °C 10% Or 2 °C min. above dew point

Max 40 °C 50 °C 85%

Drying Time Touch Dry 3h at 23 °C Recoating 12h at 23 °C Dry to handle 12h at 23 °C

SURFACE PREPARATION GUIDELINES Ensure that surfaces are dry, sound and free from dust, dirt, grease and oil before painting.

A. NEW WORK: 1. Cement plaster, concrete, gypsum plaster (e.g. Rhinolite, Cretestone), gypsum board and unglazed brick:

1.1. New or bare surfaces must be clean, dry and free from masonry salts. 1.2. Remove all defective or poorly adhering material by rubbing down using a suitable abrasive paper

or stiff brush and dust off. 1.3. Treat any area affected by mould, lichens, algae or moss with bleach. 1.4. Prime new surfaces with KANSAI ALLPURPOSE PRIMER.

2. Fibre cement:2.1. Prime with KANSAI ALLPURPOSE PRIMER.

B. PREVIOUSLY PAINTED SURFACES IN GOOD CONDITION: 1. Remove loose and flaking paint back to a sound substrate and a firm edge by scraping and

sanding. Spot prime bare areas with KANSAI ALLPURPOSE PRIMER.

Page 1 of 3


kansai acrylic texture

C. PREVIOUSLY PAINTED SURFACES IN POOR CONDITION: 1. Completely remove paint by most appropriate means e.g. scraping, coarse sanding 2. Prime the surface using PLASTER PRIMER (Solvent Based).

D. FILLING 1. Fill defects with KANSAI EXTERIOR STUCCO. Allow it to dry before applying second coat. Third

coat is recommended for extra smoothness. After drying, scuff surface using abrasive paper and dust off.

APPLICATION PROCEDURE • Apply by roller or spray working the material into the surface. • Apply at recommended spreading rates.

STORAGE & PACKAGING • Store away from direct sun, heat and severe cold. • Packaging: 18 L

CAUTIONS • For health reasons avoid dusting when preparing fibre cement surfaces. Keep surfaces wet and wash off

residues with water. • Friable and powdery surfaces require special care before painting - if in doubt contact manufacturer. • Do not paint under conditions of frost, dew, rain, fog or inclement weather. Note: Painting under the above

conditions may affect the performance of the paint film. • Avoid painting during inclement weather or if temperature is below 10 °C. • To ensure colours on a project are consistent check if the batch numbers and/or colours supplied are the

same.

SAFETY PRECAUTIONS • Keep out of reach of children. • Ensure good ventilation during application and drying. • In case of skin contact, wash with soap and water or a recognized skin cleaner. • Avoid contact with eyes – In case of contact, rinse eyes immediately with plenty of water and seek medical

advice if symptoms persist. • Harmful if swallowed. Do not induce vomiting. Seek medical attention. • Refer to Material Safety Data Sheet for complete information.

Page 2 of 3

PRODUCT CODE: DATASHEET NO: ISSUE DATE: A-421 & A-425 KPME-B-14 JUNE 2014

kansai décor texture

PRODUCT DESCRIPTION KANSAI DÉCOR TEXTURE is a water based acrylic copolymer textured coating for exterior use. Available in different texture sizes ranging from 1mm to 3 mm and can be applied by different techniques to produce a variety of textured designs.

INTENDED USAGE • To protect and decorate exterior wall surfaces. • Suitable for application to suitably primed cement plaster, concrete and brickwork.

FEATURES & BENEFITS • High build textured paint which helps

produce a variety of patterns depending on application technique.

• Covers undulation and unevenness present in the surface.



Tint Bases N.A

Generic Type Styrene Acrylic


Specific Gravity at 23oC 1,9 (approx.)

Recommended DFT per coat Varied as per texture sizes

Flash Point N.A

Theoretical Spreading Rate 0.2 - 0.7 m2/litre


Substrate Thoroughly prepared Cement plaster, concrete and gypsum plaster.

Method Putty knife or plastic trowel.

Thinning Ready for use.

Cleaning Water


Surface Temperature

Ambient Temperature

Relative Humidity


Max 40 °C 50 °C 85%



A. NEW WORK 1. Cement plaster, concrete, gypsum plaster:

1.1. Surfaces must be clean, dry, firm and free from dust, oil, grease or any other contaminants. 1.2. Remove oil, grease dirt or any other contaminants. Prime with KANSAI ALLPURPOSE PRIMER / TEX

PRIMER. B. PREVIOUSLY PAINTED SURFACES IN GOOD CONDITION

1.1. Remove loose paint and clean thoroughly. Spot prime bare areas with KANSAI ALLPURPOSE PRIMER.

C. PREVIOUSLY PAINTED SURFACES IN POOR CONDITION 1.1. Loose flaking paint must be completely removed using a paint remover or by scraping/sand

blasting. 1.2. Rinse and allow to dry.

Page 1 of 2

PRODUCT CODE: DATASHEET NO: ISSUE DATE: A-421 & A-425 KPME-B-14 JUNE 2014

kansai décor texture

1.3. Where paint surfaces have chalked on exterior exposure remove as much loose powder as possible by brushing and washing.

1.4. Proceed as for new work by making use of Plaster Primer (solvent based). D. FILLING

1.1. Fill defects and cracks with KANSAI EXTERIOR STUCCO.

APPLICATION PROCEDURE • Apply using plastic trowel. • Apply at recommended spreading rates.

STORAGE & PACKAGING • Store away from direct sun, heat and severe cold. • Packaging: 18.0L

CAUTIONS • Friable and powdery surfaces require special care before painting - if in doubt contact manufacturer. • For health reasons avoid dusting when preparing fiber cement surfaces. Keep surfaces wet and wash off

residues with water. • Do not paint under conditions of frost, dew, rain, fog or inclement weather. Note: Painting under the above

conditions may affect the performance of the paint film. • Avoid painting during inclement weather or if temperature is below 10 °C. • To ensure colours on a project are consistent check the batch numbers and/or colours supplied are the

same.



DISCLAIMER The recommendations contained herein are given in good faith and are meant to guide the specifier or the user. They are based on results gained from our tests and experiences and are believed to be reliable. No guarantee is implied by the recommendations contained herein since conditions of use, method of application and cleanliness of the substrate prior to painting are beyond our control. NB: Technology may change with time necessitating changes to this Technical Data Sheet (TDS). It is the responsibility of the user to ensure that the latest TDS is being used.

NB: TO ORDER: Quote product name, product code number, packaging and color.

KANSAI PAINT MIDDLE EAST FZCO Suite 2201, Level 22, Tower One, Boulevard Plaza, Downtown Dubai, PO Box 262746, Dubai, UAE. ): +971 4 388 2221 | (: +971 4 388 2222

Page 2 of 2

PRODUCT CODE: DATASHEET NO: ISSUE DATE: KEPT KPME-A-20 MARCH 2014

kansai epoxy texture

PRODUCT DESCRIPTION Kansai Epoxy texture is a two-pack epoxy product, which is specially formulated to be applied by spray equipment to give a textured. It can be over coated with a range of Kansai Epoxy (for Interior only) and Polyurethane top coats (for interior & Exterior).

INTENDED USAGE • To be used as an intermediary coat for interior and exterior application of Epoxy and Polyurethane based top

coats.

FEATURES & BENEFITS • Excellent adhesion to substrate

PHYSICAL PROPERTIES Appearance Matte.

Colours White.

Tint Bases N/A

Generic Type Epoxy.


Calculated Max. VOC N/A

Specific Gravity at 23oC 1.6 approx.

Recommended DFT per coat N/A

Viscosity at 23oC N/A

Flash Point >25oC

Theoretical Spreading Rate 1 - 2 m2/ litre

APPLICATION DETAILS Mixing Material is supplied in two containers as a unit.

Stir both components separately with a power mixer until homogeneous. Add the hardener to the base and mix thoroughly together. Mix 5.6 parts base with 1 part hardener.

Substrate Suitably primed and prepared surfaces.

Method Spray.

Thinning Not required.

Cleaning Clean equipment immediately after use with Epoxy thinner. It is a good practice to periodically flush out spray equipment during the course of the working day. Frequency of cleaning will depend upon amount

sprayed, temperature and elapsed time, including delays. All surplus materials and empty containers should be disposed-off in accordance with appropriate regional regulations.


Surface Temperature

Ambient Temperature

Relative Humidity


Max 30 °C 40 °C 80%

Drying Time Touch Dry 8h at 23 °C Recoating Min: 12h at 23 °C;

Max: 72h at 23oC


A. NEW WORK: 1. Cement plaster, concrete, gypsum plaster:


or stiff brush and dust off.

Page 1 of 2

PRODUCT CODE: DATASHEET NO: ISSUE DATE: KEPT KPME-A-20 MARCH 2014

kansai epoxy texture

1.3. Treat any area affected by mould, lichens, algae or moss with bleach. 1.4. Prime new surfaces with KANSAI EPOXY PRIMER.

2. Mild Steel: 2.1. Prime with KANSAI EPOXY PRIMER.


sanding. Spot prime bare areas with KANSAI EPOXY PRIMER. C. PREVIOUSLY PAINTED SURFACES IN POOR CONDITION:

1. Completely remove paint by most appropriate means e.g. scraping, coarse sanding 2. Prime the surface using KANSAI EPOXY PRIMER.

APPLICATION PROCEDURE • Apply by brush, roller or spray. • Apply one coat of epoxy primer, followed by two coats of epoxy topcoat at recommended spreading rates.

N.B. This product should not be applied directly to any substrate, but over recommended primer/intermediate coat system.

STORAGE & PACKAGING • Store away from direct sun, heat and severe cold. • Packaging: 18.0 L (Base + Hardener)

CAUTIONS • Friable and powdery surfaces require special care before painting - if in doubt contact manufacturer. • For health reasons avoid dusting when preparing fibre cement surfaces. Keep surfaces wet and wash off

residues with water. • Do not paint under conditions of frost, dew, rain, fog or inclement weather.

Note: Painting under the above conditions may affect the performance of the paint film. • Avoid painting during inclement weather or if temperature is below 10 °C.


advice if symptoms persist. • Harmful if swallowed. Do not induce vomiting. Seek medical attention. • Do not smoke while painting. • Flammable. Store in a cool dry place away from heat and sparks. • Refer to Material Safety Data Sheet for complete information.

Page 2 of 2


kansai fine coat

PRODUCT DESCRIPTION KANSAI FINE COAT is a good quality, decorative water based light textured paint with good weather resistance for exterior use.

INTENDED USAGE • To bridge and fill fine hairline cracks on exterior cement plastered walls.• To protect & decorate exterior wall surfaces.

FEATURES & BENEFITS • Good opacity and scrub resistance.• Odorless and solvent free.

• Easy to apply.



Tint Bases N.A.

Generic Type Styrene Acrylic


Calculated Max. VOC N.A.

Specific Gravity at 23oC 1.8 (approx.)


Viscosity at 23oC N.A.

Flash Point N.A.

Theoretical Spreading Rate 5 m2/liter @ 125 μm DFT



Method Brush, roller or spray.


Cleaning Water


Surface Temperature

Ambient Temperature

Relative Humidity


Max 40 °C 50 °C 85%






2. Fibre cement:2.1. Prime with KANSAI ALLPURPOSE PRIMER.

Page 1 of 2


kansai fine coat






APPLICATION PROCEDURE • Apply by roller working the material into the surface. • Apply at recommended spreading rates.


CAUTIONS • Friable and powdery surfaces require special care before painting if in doubt contact manufacturer. • For health reasons avoid dusting when preparing fibre cement surfaces. Keep surfaces wet and wash of

residues with water. • Do not paint under conditions of frost, dew, rain or fog or inclement weather. Note: Painting under the

above conditions may affect the performance of the paint film. • Avoid painting during inclement weather or if temperature is below 10 °C. • To ensure colours on a project are consistent check if the batch numbers and/or colours supplied are the

same.






Page 2 of 2

PRODUCT CODE: DATASHEET NO: ISSUE DATE: A-411 KPME-A-15 JUNE 2013

kansai heritage texture

PRODUCT DESCRIPTION KANSAI HERITAGE TEXTURE is a premium quality water based textured coating for protecting and decorating exterior walls. It provides an excellent antique effect that gives the wall an aged look.

INTENDED USAGE • To bridge and fill fine hairline cracks on exterior cement plastered walls. • To protect & decorate exterior wall surfaces.

FEATURES & BENEFITS • High build texture with elastomeric

properties. • Provides an excellent antique look.



Tint Bases N.A

Generic Type Pure Acrylic


Calculated Max. VOC LOW VOC – Less than 1 grams per liter



Flash Point N.A




Method Apply using trowel or putty knife.


Cleaning Water


Surface Temperature

Ambient Temperature

Relative Humidity


Max 40 °C 50 °C 85%






2. Fiber cement: 2.1. Prime with KANSAI ALLPURPOSE PRIMER.



PRODUCT CODE: DATASHEET NO: ISSUE DATE: A-411 KPME-A-15 JUNE 2013

kansai heritage texture




APPLICATION PROCEDURE • Apply using steel trowel. • Apply at recommended spreading rates.





same.




kansai spray texture

PRODUCT DESCRIPTION KANSAI SPRAY TEXTURE is a water based acrylic copolymer emulsion paint that has been formulated to a produce textured finish by Roller or Spray application.

INTENDED USAGE • To protect exterior wall surfaces. • To bridge and fill fine hairline cracks on exterior cement plastered walls • Suitable for application to suitably primed cement plaster, concrete and brickwork.

FEATURES & BENEFITS • Provides exceptional exterior durability. • Solvent free and environmentally friendly.

• Provides good adhesion properties for further topcoats.


Colours White.

Tint Bases N.A

Generic Type Acrylic copolymer.




Recommended DFT per coat Min. 600 μm Max. 800 μm


Flash Point N/A




Method Spray application.


Cleaning Water.


Surface Temperature

Ambient Temperature

Relative Humidity


Max 40 °C 50 °C 85%






2. Fiber cement: 2.1. Prime with KANSAI ALLPURPOSE PRIMER.

Page 1 of 3


kansai spray texture




D. FILLING 1. Fill defects with KANSAI EXTERIOR STUCCO for exterior surfaces. Allow it to dry before applying

second coat. Third coat is recommended for extra smoothness. After drying, scuff surface using abrasive paper and dust off.

APPLICATION PROCEDURE • Ready for use by spray application. • Apply one coat of recommended primer, followed by one coat of KANSAI SPRAY TEXTURE at recommended

spreading rates.

STORAGE & PACKAGING • Store away from direct sun, heat and severe cold. • Packaging: 18.0 L


residues with water. • Do not paint under conditions of frost, dew, rain or fog or inclement weather. Note: Painting under the

above conditions may affect the performance of the paint film. • Avoid painting during inclement weather or if temperature is below 10 °C. • To ensure colours on a project are consistent check if the batch numbers and/or colours supplied are the

same.



Page 2 of 3


kansai stone finish

PRODUCT DESCRIPTION KANSAI STONE FINISH is an attractive multicolour wall finish made of coloured aggregates. Consisting of ground marble and stone chips bound in a highly durable resin. Kansai Stone Finish is suitable for exterior and interior application and provides a natural stone finish featuring the colours of the selected aggregate.

INTENDED USAGE • Kansai Stone Finish is suitable for use on interior and exterior surfaces such as brick works, plaster, concrete,

gypsum board, construction blocks etc. • To protect & decorate interior and exterior wall surfaces.

FEATURES & BENEFITS • Attractive natural stone finish. • Water based coating.

• It’s tough and durable finish provides excellent weather resistance.

PHYSICAL PROPERTIES Appearance Natural Stone


Tint Bases N.A

Generic Type Acrylic binder with coloured aggregates.




Flash Point N.A




Method Spray.


Cleaning Water


Surface Temperature

Ambient Temperature

Relative Humidity


Max 40 °C 50 °C 85%


SURFACE PREPARATION GUIDELINES A. NEW WORK:

1. Cement plaster, concrete, gypsum plaster (e.g. Rhinolite, Cretestone), gypsum board and unglazed brick: 1.1. New or bare surfaces must be clean, dry and free from masonry salts. 1.2. Remove all defective or poorly adhering material by rubbing down using a suitable abrasive paper


2. Fibre cement: 2.1. Prime with KANSAI ALLPURPOSE PRIMER.



Page 1 of 2


kansai stone finish




APPLICATION PROCEDURE • Apply using spray. • Apply one coat of recommended primer, followed by two or more coats of KANSAI STONE FINISH at

recommended spreading rates. • To provide protection to the stone finish and to give it a glossy finish, apply two top coats of DESIGNER

GLAZE COAT | GLOSS

STORAGE & PACKAGING • Store away from direct sun, heat and severe cold. • Packaging: 23.0 Kg

CAUTIONS • Friable and powdery surfaces require special care before painting - if in doubt contact manufacturer. • For health reasons avoid dusting when preparing fibre cement surfaces. Keep surfaces wet and wash off



same.



Page 2 of 2


kansai stucco atlantis

PRODUCT DESCRIPTION Kansai Stucco Atlantis is a colored water-based leveling paste which provides a marble like glossy finish to the applied substrate.

INTENDED USAGE • Suitable for direct application to new cement plaster, concrete, porous brickwork and various types of

building boards.

FEATURES & BENEFITS • The controlled dosing of the components

permits the application in several coats overthe withered product without flaking orcracking.

• The micro porous structure ensures goodwater vapor permeability.

PHYSICAL PROPERTIES Appearance Gloss Finish


Tint Bases N.A

Generic Type Acrylic Co-polymer.




Recommended DFT per coat Min. 80 μm Max. 120 μm


Flash Point N/A

Theoretical Spreading Rate 5 m2/litre @ 100μm DFT

APPLICATION DETAILS Mixing Ready to use.


Method Trowel applied.


Cleaning Water.


Surface Temperature

Ambient Temperature

Relative Humidity


Max 40 °C 50 °C 85%



A. NEW WORK: 1. Cement plaster, concrete, gypsum plaster (e.g. Rhinolite, Cretestone), gypsum board, e.g. Rhinoboard), and

unglazed brick: 1.1. New or bare surfaces must be clean, dry and free from masonry salts. 1.2. Remove all defective or poorly adhering material by rubbing down using a suitable abrasive paper

or stiff brush and dust off. 1.3. Treat any area affected by mould, lichens, algae or moss with bleach. 1.4. After priming new surfaces with KANSAI PVA PRIMER, proceed to filling.

2. Fiber Cement:2.1. Prime with KANSAI PVA PRIMER. 2.2. Proceed to filling.

Page 1 of 2


kansai stucco atlantis B. PREVIOUSLY PAINTED SURFACES IN GOOD CONDITION:

1. Remove loose and flaking paint back to a sound substrate and a firm edge by scraping and sanding. Spot prime bare areas with KANSAI PVA PRIMER.

C. PREVIOUSLY PAINTED SURFACES IN POOR CONDITION: 1. Completely remove paint by most appropriate means e.g. scraping, coarse sanding 2. Prime the surface using PLASTER PRIMER (Solvent Based). 3. Proceed to filling.

D. FILLING 1. Fill defects with KANSAI INTERIOR STUCCO. Allow it to dry before applying second coat. Third coat

is recommended for extra smoothness. After drying, scuff surface using abrasive paper and dust off.

APPLICATION PROCEDURE • Apply by trowel working the material into the surface.• Apply one coat of recommended primer, followed by two or more coats KANSAI STUCCO ATLANTIS at

recommended spreading rates.

STORAGE & PACKAGING • Store away from direct sun, heat and severe cold.• Packaging: 18.0 L

CAUTIONS • Friable and powdery surfaces require special care before painting - if in doubt contact manufacturer.• For health reasons avoid dusting when preparing fiber cement surfaces. Keep surfaces wet and wash off

residues with water.• Do not paint under conditions of frost, dew, rain, fog or inclement weather. Note: Painting under the above

conditions may affect the performance of the paint film.• Avoid painting during inclement weather or if temperature is below 10 °C.• To ensure colors on a project are consistent check the batch numbers and/or colours supplied are the same.

SAFETY PRECAUTIONS • Keep out of reach of children.• Ensure good ventilation during application and drying.• In case of skin contact, wash with soap and water or a recognized skin cleaner.• Avoid contact with eyes – In case of contact, rinse eyes immediately with plenty of water and seek medical

advice if symptoms persist.• Harmful if swallowed. Do not induce vomiting. Seek medical attention.• Refer to Material Safety Data Sheet for complete information.




Page 2 of 2

the complete range of textured coatings, from kansai paint. · • friable and powdery surfaces...

Documents