the kill light® motion feeder light instructions€¦ · the kill light® motion feeder light...

The Kill Light® Motion Feeder Light Instructions

Thank you for purchasing The Kill Light® Motion Feeder Light from Elusive Wildlife Technologies, LP. Many years of testing and research have gone into developing The Kill Light® Motion Feeder Light. It is our sincere desire that you will have as much fun using it as we do. If you have not already done so, please check with your local game laws to make sure it is legal to use a light source while hunting or observing animals at night.

Elusive Wildlife Technologies, LP and its affiliates do not condone the use of these lights to illegally take game animals. Please take a moment to thoroughly read the instructions and helpful tips to get the most out of your Kill Light®, and to ensure you don’t void your warranty. Good luck and happy hunting.

Step 1

Remove the Locking Screw on the side of The Kill Light® with a Phillips screwdriver.

Step 4

Install 4 C size Alkaline batteries. Set desired motion time or timer setting. Reassemble light, and reinstall Locking Screw. See reverse page for timer settings.

Step 3

Gently separate the bottom and top half of light by pulling the top half away from the bottom half of light.

Step 2

Rotate the top of light until the white arrow moves from the lock to unlock position.

Back InsideFront

Motion - Timer Instructions

Duration After Motion Trigger1 Minute

Duration After Dusk Trigger1 Hour

Dip Switch Position

Off/Motion/Timer Switch Position

Off / Motion / Timer Switch

Switch in this position will operate the Kill Light® motion sensor timer. The light will

turn on when motion is detected and stay on for selected amount of time.


Switch in this position will operate the Kill Light® dusk-to-dawn timer. The light will turn on at dusk and run for selected

amount of time.


It is important to reset the light by moving this switch to the OFF position before mak-ing changes to the Motion - Timer dip switch

on the inside of the light.

Duration After Motion Trigger5 Minute


Dip Switch Position


Duration After Motion Trigger2 Minutes


Dip Switch Position




Dip Switch Position




Dip Switch Position



Duration After Dusk TriggerAll Night

Dip Switch Position


Operating the Kill Light® The Kill Light® can be turned OFF with the switch on the front of the light. When the switch is in AUTO (Motion) position the light will only come on at night when motion is detected, and it will stay on for the selected amount of time as described in the Motion - Timer Instructions below. When the switch is in the ON (Timer) position it will turn on at dusk and stay on for the selected amount of time. The on/off switch is almost flush with the front of the light to prevent animals from accidentally turning the light on or off.

Important The Kill Light® Motion Feeder Light should be reset before making changes to the Motion-Timer dip switch settings on the inside of the light. To do this, turn the Off/Auto/On switch on the front of the light to the Off position before making changes to the Motion-Timer dip switches. Once the Motion-Timer dip switches are changed to the desired setting then move the Off/Auto/On switch on the front of the light to the Auto (for motion activation) or On (for dusk-to-dawn timer activation) position.

Mounting the Kill Light®The Kill Light® is designed to be mounted in three ways.

1. Magnetically attach The Kill Light® to the bottom of your feeder control unit or barrel.

2. Hang on your feeder varmint cage by installing one of the quick clips directly to the center swing out loop on the back of the light and attach the light to the varmint cage. You can also hang the light from a tree limb where you know hogs roam or root around, and bait that location if allowed in your state.

Helpful Tip If it is windy or if it could become windy do not hang the light by the center swing out loop. Use the 3 outside swing out loops and attach a quick clip to all 3, then hang to your varmint

cage to prevent the light from blowing around in the wind. This could cause the animals to be spooked by their own shadows dancing around.

3. Permanently attach under your feeder by using the three self drilling screws and metal tab protectors. Simply place a metal protector tab over the plastic mounting tab on the light and install the self drilling screws. Important The metal protector tabs have been included with your light, and must be used when permanently mounting to prevent animals from chewing on the tabs and causing the light to possibly fall off the feeder.

Powering the Kill Light®The Kill Light® operates on 4 C batteries, and will last approximately 25–30 days if set to come on for one minute after motion is detected or 7–10 days if set to stay on all night. The Kill Light® can also be powered by the optional power cord that has been included with your Kill Light®. The optional power cord can be used to power the light from an auxiliary 6 or 12 volt DC power source. A 6 or 12 volt feeder battery will operate the light, but not as long as with the 4 C batteries. It is highly recommended that if you decide to power your light longer and make it maintenance free with this cord that you use a large 12 volt car battery or deep cycle marine type battery, a charge controller, and a 10 watt solar panel on the battery to ensure the battery will stay charged and have enough current to power the light every night.

WarrantyElusive Wildlife Technologies, LP warranties this product for one year from the original purchase date. Please complete the warranty registration and mail it in to register your light. You may also e-mail the warranty registration information to [email protected].

Your Kill Light® is NOT waterproof. It is water resistant ONLY when used as intended. The Kill Light® must be hung or mounted level

with the LED’s facing the ground to prevent water damage from rain or condensation. Take care to insure the light is mounted properly and always install the light safely inside a varmint cage when leaving the light on a feeder for extended periods of time. Elusive Wildlife Technologies, LP will not warranty any light damaged by user neglect or failure to adhere to these instructions and guidelines. No lights will be warranted due to water penetration or from animal damage.

Please mail or e-mail warranty info to:Elusive Wildlife Technologies, LP

1107 West Dallas Street • Suite A • Conroe, TX 77301800-780-6861 • [email protected]

Date of Purchase _______________________________________ q Ms. q Mr.

Name ________________________________________________________

Address _______________________________________________________

City, State, Zip ___________________________________________________

Phone ________________________________________________________

E-mail ________________________________________________________

q Received as a gift q Purchased for yourself

Name of store where purchased ________________________________________

Please rate your satisfaction with this product from 1–10 with 10 being the most satisfied. If you have not used this product please enter N/A. ________

Elusive Wildlife Technologies, LP respects your privacy, and we will not sell or provide personal information to any other party. However, we would like to occasionally send you information about your Elusive Wildlife product or special offer. If you do not wish to receive this information please check here q.

the kill light® motion feeder light instructions€¦ · the kill light® motion feeder light...

Documents