the sources of wind noise in hearing aids
DESCRIPTION
z. INTRODUCTION Wind causes noise at the output of hearing aids, and this is a major problem to hearing aid wearers. While the cause is known to be associated with turbulence at the input to the hearing aid microphone, little is known about the nature or source(s) of this turbulence. AIM - PowerPoint PPT PresentationTRANSCRIPT
The sources of wind noise in hearing aidsBy Harvey Dillon, Inge Roe, and Richard Katsch, National Acoustic Laboratories
This project was kindly sponsored by GN Resound, Oticon, Phonak AG, and Widex
1. Wind Flow Around the Head and Ear
ITECIC BTE
Turbulence decreases rapidlywith distance out from the head
(for frontal wind incidence)
Turbulence velocity (frontal wind at 5 m/s)
Mean wind flow around the ear (for frontal wind at 5 m/s)
Wind direction changes rapidly inside and
just outside the concha
Out from canal entrance
Transverse velocity (m/s)Downwind velocity (m/s) Vertical velocity (m/s)
CIC CICCICCIC
When wind flows past an obstacle, the stream lines separate and recombine. This process creates turbulence. Turbulence comprises rapid alteration of wind flow direction and rapid alteration of wind pressure. These pressure fluctuations can directly activate a microphone diaphragm or can cause a sound wave to propagate outwards from the turbulence.
Turbulence has strong components at the frequency:
f = US/L
where U is the mean wind velocity
S is the Strouhal number ( = 0.2 for a cylinder)
L is the width of the obstacle
Large obstacles, like the head, should therefore produce low frequency noise. Smaller obstacles, like the pinna should produce mid-frequency noise. Very small obstacles, like the tragus or a microphone inlet port, should produce high frequency noise. Turbulence is strongest at the point at which eddies shed from the downwind side of the obstacle.
BACKGROUND THEORY
AIMThe aims of the study were to:1. Quantify the amount of noise caused by wind.2. Identify the sources of the turbulence causing the noise.
Acoustically deadened wind tunnel
A wind tunnel with a working area of 750 mm x 750 mm contains air-flow straighteners and sound absorbers. It allows wind speeds up to 5 m/s to be obtained.
Laser doppler velocimeter
Six laser beams create interference patterns, which allow the instantaneous velocity of individual smoke particles to be measured in three dimensions.
Coordinate system
The x coordinate corresponds to distance along the wind tunnel, the y coordinate is laterally out from the head, and the z coordinate is motion vertically upwards.
x
z
y
METHOD
• Flow was measured by measuring the velocity of smoke particles at multiple sites around the ear using a laser doppler velocimeter.
• SPL was measured using a hearing aid microphone positioned over the ear or inserted inside earmolds shaped like ITE, ITC or CIC hearing aids.
INTRODUCTIONWind causes noise at the output of hearing aids, and this is a major problem to hearing aid wearers. While the cause is known to be associated with turbulence at the input to the hearing aid microphone, little is known about the nature or source(s) of this turbulence.
2. Sound Pressure Levels at the Hearing Aid Microphone
At 0° incidence, the pinna is a major source of turbulence.
At -50° incidence, the head causes large, low-frequency eddies which detach near the pinna causing high
noise levels. The pinna reduces turbulence as they detach.
At 90° incidence, the flow separates and does not come near either pinna,
so noise levels are relatively low.
• Wind noise has a broad spectrum whose shape depends on wind direction, and the spectrum extends down to very low frequencies
• Obstacles (head, pinna, tragus) can act as:
Wind guards
Turbulence source
Turbulence shedder
• The head creates low-freq turbulence, especially on down-wind side
• The pinna creates medium-frequency turbulence, especially at position of BTE microphone
• Small obstacles (e.g. tragus and microphone inlet port) create high-frequency turbulence.
• BTEs are noisiest because the microphone is in the wake of the pinna.
• CICs are least noisy for most angles because the microphone is shielded by the concha.
• ITEs are least noisy for some angles and frequencies because the aid and the pinna form a smooth surface.
• Levels are very intense, even for a light breeze
• Noise levels easily saturate hearing aids.
Conclusions
Tragus Tragus
ITE
ITC and CIC aids are shielded from turbulence created by the head, but are in the path of turbulence created by the tragus, pinna and concha. The profile is smoother for ITEs.
40
50
60
70
80
90
100
25 50 100 200 400 800 1600 3150 6300
Frequency (Hz)
1/3
oct
ave
leve
l (d
B S
PL
)
BTE
ITE
ITC
CIC
BTE
ITE
ITC
CIC
0 degrees
40
50
60
70
80
90
100
25 50 100 200 400 800 1600 3150 6300
Frequency (Hz)
1/3
octa
ve le
vel (
dB S
PL)
-90-60-300306090
BTE
40
50
60
70
80
90
100
25 50 100 200 400 800 1600 3150 6300
Frequency (Hz)
1/3
oct
ave
level
(d
B S
PL
)
BTE
ITE
ITC
CIC
BTE no ear
BTE
ITE
ITC
30 degrees
40
50
60
70
80
90
100
25 50 100 200 400 800 1600 3150 6300
Frequency (Hz)
1/3
oc
tav
e le
ve
l (d
B S
PL
)
BTE
ITE
ITC
CIC
BTE no ear
CIC
BTE
- 50 degrees (far side)
50
60
70
80
90
100
-90 -60 -30 0 30 60 90
Azimuth (degrees)
1/3
oct
ave
leve
l (d
B S
PL
)2 kHz
100 Hz
ITE
Much lower noise levels at the BTE position when the pinna is detached
Low frequency emphasis when wind comes from the far side.
Broad spectrum whenthe head and pinna both
contribute to noise
Local maximum at -50° created by
head eddies
Local maximum at0° created by tragus eddies
ITE quieter than ITC or CIC over the frequency range
where the tragus causes turbulence
Slightly higher noise levels at the BTE position when the pinna is detached