the use and management of tritium in iter
DESCRIPTION
The Use and Management of TRITIUM in ITER. R. Lässer. Content. Introduction Inner and outer Fuel Cycle of a Fusion Reactor Radiotoxicity of tritium Tritium in gases, liquids and metals Preconditions of safe processing tritium Tritium experiments in Tokamaks - PowerPoint PPT PresentationTRANSCRIPT
4 July 2008 R. Laesser, F4E ITER Department 2
Content• IntroductionIntroduction
o Inner and outer Fuel Cycle of a Fusion Reactoro Radiotoxicity of tritiumo Tritium in gases, liquids and metalso Preconditions of safe processing tritiumo Tritium experiments in Tokamaks
• The Deuterium Tritium (DT) Fuel CycleThe Deuterium Tritium (DT) Fuel Cycleo Subsystems of the DT Fuel CycleSubsystems of the DT Fuel Cycle
Storage and Delivery System, Long Term System Vacuum Pumping Systems Tokamak Exhaust Processing System Isotope Separation System Water Detritiation System
o Topics addressed in WP7 (Tritium Plant) during ITER Design Review Tritium building layout Modification of HVAC, ADS and VDS Tritium Tracking Strategy
• Tritium in Plasma Facing Components Tritium in Plasma Facing Components • Tritium Processing in Test Blanket ModulesTritium Processing in Test Blanket Modules• Tritium Processing in DEMOTritium Processing in DEMO• Acknowledgements
4 July 2008 R. Laesser, F4E ITER Department 3
Plasma
Li
Be
Li
PlasmaExhaust
DT FuelSupply
DeuteriumSupply
Clean-up and DTFuel Recovery
TritiumRecovery
Vacuum Pumps
Helium to Stack
BreedingBlanket
He Purge Gas+ Tritium fromBlanket
TritiumSupply
Blower
The Inner and Outer Fuel Cycle of Fusion Reactors
Among the potential fusion reactions technically most suitable is the reaction between deuterium and tritium
2D + 3T→ 4He (3.5 MeV) + 1n (14.1 MeV) – 0.016 at% Deuterium are contained in
natural water.– Tritium needs to be produced.
• 56 kg tritium is required per GWyof fusion power.
• About 100 g tritium is produced peryear in a standard CANDU fission unit.
• Breeding of tritium is necessary in a fusion reactor:
n + 6Li → T + 4He n + 7Li → T + 4He + n
• 20 to 25 kg tritium will be needed for operation of ITER.
• A few kg tritium will be always needed for starting a power fusion reactor.
08/29
Tritium Plant
TES
4 July 2008 R. Laesser, F4E ITER Department 4
Radiotoxicity of TritiumRadiotoxicity of Tritium Tritium decays: 3T → 3He+ + β- + ν + 18.6 keV. T1/2 = 12.3 y
Tritiated hydrogen (HT, DT, T2) breathed-in by the lounges leads to a local β- dose, but is almost completely breathed out. Also the uptake of hydrogen (tritium) through the skin is very small. Q2 stands for: H2, HD, HT, D2, DT, T2.
Tritiated water vapour (HTO, DTO, T2O) is readily incorporated via the
lounges and the skin. Within a few hours tritiated water is homogeneously distributed in the body fluids and causes a whole body dose which can easily be determined by measuring the tritium concentration in the urine or in the breathed out air. (Q2O stands for: H2O, HDO, HTO, D2O, DTO, T2O.
Biological half life: about 10 days. Organically bound tritium: half life time: months.
Tritiated water is approximately 25000 times more radiotoxic than tritiated hydrogen.
In consequence: Tritium is one of the least radiotoxic nuclides.
Tritium can induce X-rays.
4 July 2008 R. Laesser, F4E ITER Department 5
Effects of Tritium in Gases and Liquids Effects of Tritium in Gases and Liquids
Tritium in gasesTritium in gasesComposition and pressure of tritiated gas mixtures change due to tritium decay:• 3He is generated. • Radicals, new and ionized gas molecules can be created by the decay electrons.
Even solid matter such as plastics can be produced if hydrocarbons are present.
Tritium in waterTritium in waterAt high T-concentrations in the water radiolysis occurs with generation of oxygen,
hydrogen and tritiated peroxide. Storage of highly tiritiated water needs a recirculation loop with small hydrophobic catalyst to recombine hydrogen and oxygen again (5 liter of HTO create about 20 liter of DT per day).
Tritium gas in contact with metal surfacesTritium gas in contact with metal surfacesMetal oxides can be reduced by tritium resulting in clean metallic surfaces (leading to
diffusion limited permeation (not any more surface limited)). As a consequence of these reactions the purity of the tritium gas stored in a container will deteriorate.
4 July 2008 R. Laesser, F4E ITER Department 7
PRECONDITIONS FOR SAFE PROCESSING TRITIUMPRECONDITIONS FOR SAFE PROCESSING TRITIUM
•Tritium compatible materials/equipment: No plastics / oil. Yes: metals / ceramics.
•Confinement of tritium:
o Primary confinement: prevents T-releases into the areas accessible by workers by means of barriers: primary containment can be surrounded by intermediate volumes or secondary containments (glove- or valve box).
o Secondary confinement: prevents T-releases into non-controlled/non-supervised areas and into the environment.
•Simple design and use of well proven techniques: The design must allow easy maintenance and repair.
•Stringent installation and commissioning procedures: Stringent leak tightness requirement: <10-10 Pam3/s for facilities and <10-11 Pam3/s for components.
•Strict operational and local procedures.
•Equipment to be installed in well ventilated buildings.
•Tritium inventories to be limited and segregated as far as possible.
4 July 2008 R. Laesser, F4E ITER Department 8
TRITIUM EXPERIMENTS IN TOKAMAKSTRITIUM EXPERIMENTS IN TOKAMAKS
Preliminary Tritium Experiment (PTE) at JET: end of 1991First DT experiments in a fusion machine, limited number of plasma shots,
less than 0.2 g of tritium on site. No recycling of tritium.
Tritium Processing during Tritium Campaign at TFTR (1994-1997)Maximum site inventory 5 g, 78 g were supplied to NBI, most of the T-
processing was done at other US site, very limited recycling.
Tritium Processing during Deuterium Tritium Experiment (DTE) at JET in 1997
Tritium amount on site: 20 g, Active Gas Handling System (AGHS =JET Tritium Plant) supplied 100 g T, 11.5 g was highest tritium amount trapped in tiles + flakes. Tritium was recycled five times.
Trace Tritium Experiment (TTE) at JET in October 2003Operation of AGHS during TTE in similar way as during the DTE, however
only very small amounts of tritium were injected into the machine.
4 July 2008 R. Laesser, F4E ITER Department 9
Cryogenic Cryogenic pump: 4.2K pump: 4.2K cold finger, cold finger,
He dewar He dewar was moved was moved by a lifting by a lifting platformplatform
T2 supply from U-beds + injection via NBI
345 liter vessel used
for (pVT-c) accountancy
Hydrogen/tritium
storage in large JET
U-beds, cracking
of impurities
Very simple Tritium
Processing Systems (all
equipment shown)
PTE at JET 1991
2 U-beds2 U-beds
TT
6Ø cm
4 U-beds4 U-beds
4 July 2008 R. Laesser, F4E ITER Department 10
MechanicalForevacuum
(MF)
ExhaustDetritiation
(ED)
ImpurityProcessing
(IP)
Analytica lLaboratory
(AN)
Isotope Separation
Isotope Separation
Gas chroma-tography
(G C)
Cryo-distilla tion
(CD)
CryogenicForevacuum
(CF)
H (D )2 2
Torus Basement
Torus Hall
Active G as Handling System (AGHS)
JG00
.34/
1c
Intermediate Storage(IS)
ProductStorage
(PS)
GasIntroduction
box (G I)
D2D 2
D 2
D 2
D2
D 2
D 2
T 2
T2T2
T2
T2
T2
T2
T2
Gas DistributionBox (GD)
TORUS
NIB 8
NIB 4
Monitoring
D iagnostics
GIM 15
TDGIS TDGIS
CRYO
CR
YO
CRY
OP
UM
P
CRYOPUMP
NIB
Au
xilia
ry v
en
tila
tion
NIB
Cro
wn
Am
ers
ha
m U
Ðb
ed
Toru
s C
row
n
M L2M L1
AGHS
Building
DTE: Use of Active Gas Handling
System (AGHS): 1997
Bridge: Cryogen + active gas lines
Stack
Cryogenic Forevacuum System Control Room
Torus Basement AGHS
4 July 2008 R. Laesser, F4E ITER Department 11
The Deuterium Tritium (DT) The Deuterium Tritium (DT) FUEL CYCLE of ITER FUEL CYCLE of ITER
Tritium fuelling via
• Pellet injection,
• Gas puffing.
NBI not used for tritium injection.
Closed DT loop required especially with respect to tritium as tritium releases into the environment must be kept as low as
reasonable achievable (ALARA).
4 July 2008 R. Laesser, F4E ITER Department 12
Storage and DeliverySystem
Torus Cryo PumpsRoughing Pumps
Tokamak ExhaustProcessing
Isotope SeparationSystem
Analytical System
Fuelling SystemsNeutral Beam Heating
Water Detritiation
Off-gasRelease
Torus
Neutral Beam InjectorCryo Pumps
Tritium / Deuteriumfrom External Sources
ProtiumRelease
Tritium BreedingTest Blanket
Atmosphere and VentDetritiation Systems
Automated Control System & (Hard Wired) Safety System
DiagnosticsFirst Wall Cleaning
Long Term Storage
MBA 2
EU
Korea, Fund
Korea, Fund
EU, Fund
JA,Fund
EU, Fund
All Participating Teams US, Fund
Fund
FundEU, US All Participating Teams, Fund
CN, EU, JA, US, Fund
10/29
The ITER DT Fuel CycleThe ITER DT Fuel Cycle
Leak Detection
EU
4 July 2008 R. Laesser, F4E ITER Department 14
The ITER ("the way") Project (2/3)
04/29
The ITER BUILDINGSThe ITER BUILDINGSNuclear Nuclear BuildingsBuildings
4 July 2008 R. Laesser, F4E ITER Department 15
Subsystems of the DT Fuel Cycle• Storage and Delivery System (SDS) and Long term Storage (LTS)• Vacuum Pumping Systems: Cryo- and Roughing Pumps• Tokamak Exhaust Processing System (TEP)• Isotope Separation System (ISS) (throughput 200 Pam3/s)• Water Detritiation System (WDS)• Analytical System (ANL)• Fuelling Systems
o Pellet Injectiono Neutral Beam Injectiono Gas Puffing
• Atmosphere and Vent Detritiation Systems
• 120 Pam3/s for 3000 s (about 1 kg DT/h),• 160 Pam3/s for 1000 s,• 200 Pam3/s for 400 s,
Fuelling rate can increase for short times 230 Pam3/s (for ELMs pacing).
Fuelling rates:
4 July 2008 R. Laesser, F4E ITER Department 16
Storage and Delivery System + Long Term System (KO)Storage and Delivery System + Long Term System (KO)Purpose of Storage and Delivery System (SDS)• To store tritium and deuterium in storage beds (70 g tritium/bed), • To supply gases of the requested compositions and flow rates to the fuelling
systems,• To perform accountancy by in-bed calorimetry (accuracy: ~1% for fully loaded bed)
and (pVT-c) measurements,• To collect He-3.Purpose of Long Term System (MBA-2 in ITER)• To store the tritium in 10 getter beds (without accountancy) to keep total tritium
inventory in FC at low value. • To import and account tritium supplied to ITER,
Safest storage technique of tritium todaySafest storage technique of tritium today is the use of metal getter beds with high affinity to hydrogen.
Advantages: Storage beds can act as pumps at RT and compressors at higher temperatures. Negligible tritium permeation at RT. Purity of the dissolved tritium is conserved. Removal of 3He from tritium possible. High storage capacity per volume. In-bed calorimetry possible.
Disadvantages: needs heating to temperatures around 400-500°C. Low thermal conductivity of metal hydride powder critical for achieving high hydrogen supply rates. Powder is pyrophoric. Possibility of He-blanketing. Large volume increase of metal after hydriding due to power production. Creation of tritiated waste.
4 July 2008 R. Laesser, F4E ITER Department 17
Storage and Delivery System + Long Term System (KO)Storage and Delivery System + Long Term System (KO)
ITER Getter beds still to be optimized (requiring thermomechanical / hydraulic calculations) for
• Fast supply,• Fast pumping, • Space needed for hydrided materials,• Accurate accountancy,• Fast cooling.
IO and Korea still prefer ZrCo instead of uranium (U). ZrCo disproportionates in the presence of higher hydrogen pressures: (2 ZrCo + H2 = ZrCo2 + ZrH2). Pumps are requested to keep the pressure in the beds low to avoid disproportionation.
Reproportionation is possible under vacuum at higher temperature. Memory effects exist.
No long term experience of ZrCo with tritium exist. However tritium experience with U is huge. U has very broad horizontal plateau pressure, whereas this pressure increases in the case of ZrCo.
EU strongly in favor of using uranium as getter material.
4 July 2008 R. Laesser, F4E ITER Department 18
Vacuum Pumping:• 8 Torus-, 2 cryostat cryopumps
• 3 HNB-, 1 DNB cryopumps
• Cold Valve boxes + cryojumpers
4.5K cryosorption panel circuit
Integral inlet valve
80K louvre baffles
Valve pneumatic actuator
Pump connection flange
Vacuum Pumping Systems (EU)
Purpose: Pumping Torus (153 Pam3/s), cryostat and HNB and DNB facilities.
Pumping tests with a half size model cryopump successfully finished. Final design of a full prototype torus cryopump (PTC) in progress: 1.8 m diameter; 2.1 m long; 11.2 m2 charcoal coated, 0.8 m diameter inlet valve with 0.5 m stroke to modify pumping speed.
No regeneration required during short plasma pulses (450 s). During long shots (3000 s) quasi-continuous regeneration occurs up to 100K for release of helium and hydrogen to recycle the released hydrogen.
Prototype Torus Cryopump
4 July 2008 R. Laesser, F4E ITER Department 19
Regeneration separates gas stream:• 80K: Q2 and He (Ne): every 150 seconds.
• 300K: Air-like impurities (CO, CO2, lower CnQm), daily regeneration of all cryopumps (overnight).
• 470K: Water-like impurities (higher CnQm), regeneration of one cryopump (overnight).
Vacuum Pumping Systems (EU)
Rough Pumping System: Combination of Roots pump (1 off 4200 and 2 off 1200 m3/h and screw- or piston pumps). Separation of pumping and oil filled volumes by special seals (e.g. ferrofluidic seals).
Proposal to freeze out the highly tritiated water (from the 470K regeneration) upstream of Roots pumps to avoid condensation.
1 module with 4 sections
1 section
HNB cryopump
80 K
5K5K
Schematic of HNB
Ion Source
CryopanelsNeutraliser
4 July 2008 R. Laesser, F4E ITER Department 20
Tokamak Exhaust Processing (TEP) System (US)Tokamak Exhaust Processing (TEP) System (US)
Purpose of TEPto treat all gases from various systems (NBI, TP, Diagnostics) to • extract hydrogen in water vapour and hydrocarbons,• discharge the hydrogen depleted streams via vent detritiation (TEP
release conditions relaxed from 1 Ci/m3 to 200 Ci/m3).
Replacement of carbon by W will simplify the requirements of TEP as hydrocarbons will be no longer the dominant impurities.
Main components of TEP• Permeators to extract the unburnt fuel (hydrogen) from the gas mixtures,• Catalysts to crack the hydrogen containing molecules and permeators to
extract the produced hydrogen,• Pumps for circulation of the gases.
Unresolved topic: Processing of highly tritiated water
4 July 2008 R. Laesser, F4E ITER Department 21
Highly Tritiated Water
1 kg DTO contains 143 g tritium or 1.4 MCi.
High tritium concentrations in water are expected from various sources such as 470K regenerations of cryopumps, during dedicated phases for recovery of the tritium trapped inside the VV and from Hot Cell.
4 July 2008 R. Laesser, F4E ITER Department 22
Processing Options of Highly Tritiated Water
Reduction of DTO to DT by means of Reduction of DTO to DT by means of
– Electrolysis of DTO (1.4 MCi/kg)
• Electrolysis of liquid water very difficult above 2000 Ci/kg, leads to further enrichment.
– Metals such as magnesium, uranium or iron
• Reaction with iron is not complete (75% conversion at 500°C), however reversible
– Decontamination factor limited to about two orders of magnitude
• Exothermic reaction with magnesium or uranium
– Highly tritiated waste (Mg / MgO containing MgO2DT)
– Carbon monoxide (water gas shift reaction): CO + DTO = CO2 + DT
Isotopic exchange of DTO with HIsotopic exchange of DTO with H22 to DT and H to DT and H22OO
– Exchange in liquid water (Liquid Phase Catalytic Exchange (LPCE))
– Exchange in vapor phase (Vapor Phase Catalytic Exchange (VPCE))
24/29
4 July 2008 R. Laesser, F4E ITER Department 23
Use of Isotopic Exchange: DTO + HUse of Isotopic Exchange: DTO + H22 = H = H22O + DTO + DT
Use of Liquid Phase Catalytic Exchange (LPCE): Outline Use of Liquid Phase Catalytic Exchange (LPCE): Outline conceptual designconceptual design– 4,2 g/h (100 g/day) DTO vapor flow rate
– 72 g/h H2O liquid water feed flow rate (mixing factor 20)
• Water for mixing could be tritium contaminated• Moisture in HT to be condensed and returned
– 48 g/h H2 flow rate (molar ratio 6)
• Trade off to mixing factor, column length, outlet concentration
• H2 to be added could also be slightly contaminated
– 80 g/h (4.2 mol/h) tritiated water flow rate at 150 Ci/kgto Water Detritiation System (capacity > 20 kg/h @ 10 Ci/kg)
Column height about 4 m, column diameter about 3 cm
Upper section of the column to be easily replaceable
– Catalyst lifetime could be limited due tohigh tritium concentration (no problem for VPCE)
25/29
DTO vapor fromsublimation
liquid waterHT
(saturated) to ITERISS
packing
catalyst
tritiated water
to ITERWDS
bottledsupply
H2
LPCE column
or electrolyser
80 g/h Q2O/h, 12 Ci/h
4.2 g/h DTO, 5.9 kCi/h
72 g/h H2O
4 July 2008 R. Laesser, F4E ITER Department 24
Isotope Separation System (ISS) utilizes cryogenic distillation and catalytic reaction for isotope exchange to produce the required hydrogen isotope gas mixtures.
Purpose of ISS
•To accept the hydrogen isotope mixtures (up to 200 Pam3/s) from TEP, NBI and WDS.
•To produce the required pure deuterium (<0.02% T, <0.5% H) and 90% T/10% D gas mixtures for the users and SDS.
•To transfer detritiated (<0.1 ppm T) hydrogen to WDS for further detritiation and final release.
Column-1
Protium (Deuterium) Reject
Eq-2
Eq-3
Eq-5
Column-2
Column-3
Column-4
Eq-6
Eq-1
D2 (T) forRefueling
D2 (NBInjection)
PlasmaExhaust
Eq-4
90 % T / 10 % D
HD (T)Feed
Pump
Eq-7
DT (50 %)Product
4 columns installed in
cold- box
ISSIsotope Separation System (EU)