theories of failure failure of a member is defined as one of two conditions. 1.fracture of the...
TRANSCRIPT
![Page 1: Theories of Failure Failure of a member is defined as one of two conditions. 1.Fracture of the material of which the member is made. This type of failure](https://reader036.vdocument.in/reader036/viewer/2022081511/56649f2a5503460f94c44a01/html5/thumbnails/1.jpg)
Theories of FailureFailure of a member is defined as one of two conditions.
1. Fracture of the material of which the member is made. This type
of failure is the characteristic of brittle materials.
2. Initiation of inelastic (Plastic) behavior in the material. This
type of failure is the one generally exhibited by ductile materials.
When an engineer is faced with the problem of design using a specific
material, it becomes important to place an upper limit on the state of
stress that defines the material's failure. If the material is ductile, failure
is usually specified by the initiation of yielding, whereas if the material
is brittle it is specified by fracture. 1
![Page 2: Theories of Failure Failure of a member is defined as one of two conditions. 1.Fracture of the material of which the member is made. This type of failure](https://reader036.vdocument.in/reader036/viewer/2022081511/56649f2a5503460f94c44a01/html5/thumbnails/2.jpg)
These modes of failure are readily defined if the member is subjected to
a uniaxial state of stress, as in the case of simple tension however, if the
member is subjected to biaxial or triaxial stress, the criteria for failure
becomes more difficult to establish.
In this section we will discuss four theories that are often used in
engineering practice to predict the failure of a material subjected to a
multiaxial state of stress.
A failure theory is a criterion that is used in an effort to predict the
failure of a given material when subjected to a complex stress condition.
2
![Page 3: Theories of Failure Failure of a member is defined as one of two conditions. 1.Fracture of the material of which the member is made. This type of failure](https://reader036.vdocument.in/reader036/viewer/2022081511/56649f2a5503460f94c44a01/html5/thumbnails/3.jpg)
i. Maximum shear stress (Tresca) theory for ductile materials.
ii. Maximum principal stress (Rankine) theory.
iii. Maximum normal strain (Saint Venan’s) theory.
iv. Maximum shear strain (Distortion Energy) theory.
Several theories are available however, only four important theories are
discussed here.
3
![Page 4: Theories of Failure Failure of a member is defined as one of two conditions. 1.Fracture of the material of which the member is made. This type of failure](https://reader036.vdocument.in/reader036/viewer/2022081511/56649f2a5503460f94c44a01/html5/thumbnails/4.jpg)
Maximum shear stress theory for Ductile Materials
The French engineer Tresca proposed this theory. It states that a
member subjected to any state of stress fails (yields) when the
maximum shearing stress (τmax)in the member becomes equal to the
yield point stress (τy)in a simple tension or compression test (Uniaxial
test). Since the maximum shear stress in a material under uniaxial stress
condition is one half the value of normal stress and the maximum
normal stress (maximum principal stress) is max, then from Mohr’s
circle.
2max
max
4
![Page 5: Theories of Failure Failure of a member is defined as one of two conditions. 1.Fracture of the material of which the member is made. This type of failure](https://reader036.vdocument.in/reader036/viewer/2022081511/56649f2a5503460f94c44a01/html5/thumbnails/5.jpg)
5
![Page 6: Theories of Failure Failure of a member is defined as one of two conditions. 1.Fracture of the material of which the member is made. This type of failure](https://reader036.vdocument.in/reader036/viewer/2022081511/56649f2a5503460f94c44a01/html5/thumbnails/6.jpg)
If both of principal stresses are of the same sign tension
compression then
σ1 <σy (4)
σ2 <σy (5)
In case of Biaxial stress state
)3(
22
)2(22
21
21
max
21minmaxmax
y
y
y
6
![Page 7: Theories of Failure Failure of a member is defined as one of two conditions. 1.Fracture of the material of which the member is made. This type of failure](https://reader036.vdocument.in/reader036/viewer/2022081511/56649f2a5503460f94c44a01/html5/thumbnails/7.jpg)
A graph of these equation is given in the figure. Any given state of
stress will be represented in this figure by a point of co-ordinate 1 and
2 where 1 and 2 are two principal stresses. If these point falls within
the area shown, the member is safe and if outside then member fails as
a result of yielding of material. The Hexagon associated with the
initiation of yield in the member is known as “Tresca Hexagon”. (1814-
1885). In the first and third quadrant 1 and 2 have the same signs and
7
![Page 8: Theories of Failure Failure of a member is defined as one of two conditions. 1.Fracture of the material of which the member is made. This type of failure](https://reader036.vdocument.in/reader036/viewer/2022081511/56649f2a5503460f94c44a01/html5/thumbnails/8.jpg)
max is half of the numerically larger value of principal stress 1 or 2. In
the second and fourth quad, where 1 and 2 are of opposite sign, max is
half of arithmetical sum of the two 1 and 2.
In fourth quadrant, the equation of the boundary or limit
(yield/boundary stress) stress line is
1 - 2 = y
And in the second quadrant the relation is
1 - 2 = -y
8
![Page 9: Theories of Failure Failure of a member is defined as one of two conditions. 1.Fracture of the material of which the member is made. This type of failure](https://reader036.vdocument.in/reader036/viewer/2022081511/56649f2a5503460f94c44a01/html5/thumbnails/9.jpg)
y 21
y 1
y 1
y 2
y 21
y 2
9
![Page 10: Theories of Failure Failure of a member is defined as one of two conditions. 1.Fracture of the material of which the member is made. This type of failure](https://reader036.vdocument.in/reader036/viewer/2022081511/56649f2a5503460f94c44a01/html5/thumbnails/10.jpg)
Problem 01:-
The solid circular shaft in Fig. (a) is subject to belt pulls at each
end and is simply supported at the two bearings. The material has a
yield point of 36,000 Ib/in2• Determine the required diameter of the
shaft using the maximum shear stress theory together with a safety
factor of 3.
10
![Page 11: Theories of Failure Failure of a member is defined as one of two conditions. 1.Fracture of the material of which the member is made. This type of failure](https://reader036.vdocument.in/reader036/viewer/2022081511/56649f2a5503460f94c44a01/html5/thumbnails/11.jpg)
400 + 200 lb200 + 500 lb
11
![Page 12: Theories of Failure Failure of a member is defined as one of two conditions. 1.Fracture of the material of which the member is made. This type of failure](https://reader036.vdocument.in/reader036/viewer/2022081511/56649f2a5503460f94c44a01/html5/thumbnails/12.jpg)
12
![Page 13: Theories of Failure Failure of a member is defined as one of two conditions. 1.Fracture of the material of which the member is made. This type of failure](https://reader036.vdocument.in/reader036/viewer/2022081511/56649f2a5503460f94c44a01/html5/thumbnails/13.jpg)
0
42800
64
24200
.42006700
.36006600
64
2
3
4
4
y
x
x
B
x
d
d
d
inlbMc
inlbM
dI
dc
I
Mc
13
![Page 14: Theories of Failure Failure of a member is defined as one of two conditions. 1.Fracture of the material of which the member is made. This type of failure](https://reader036.vdocument.in/reader036/viewer/2022081511/56649f2a5503460f94c44a01/html5/thumbnails/14.jpg)
inlb
OR
inlb
T
d
d
d
J
Tr
xy
xy
.480024200
24)200400(
.480016300
16)200500(
480,24
32
24800
3
4
xyyx
yxxy
3
480,24
dxy 3
800,42
dx
x
14
![Page 15: Theories of Failure Failure of a member is defined as one of two conditions. 1.Fracture of the material of which the member is made. This type of failure](https://reader036.vdocument.in/reader036/viewer/2022081511/56649f2a5503460f94c44a01/html5/thumbnails/15.jpg)
2
2
21
max21
22
2
know weAs
xyyx
3
36000
2)(
2...
...
And
21
21
max
FOS
SOF
SOF
yield
yield
y
15
![Page 16: Theories of Failure Failure of a member is defined as one of two conditions. 1.Fracture of the material of which the member is made. This type of failure](https://reader036.vdocument.in/reader036/viewer/2022081511/56649f2a5503460f94c44a01/html5/thumbnails/16.jpg)
''76.1
480,24
2
428001036
480,24
2
42800
2
000,12
480,24
2
428002
3
000,36
480,24
2
428002
2
3
2
36
2
3
2
3
2
3
2
3
2
3
2
321
d
dd
dd
dd
dd
16
![Page 17: Theories of Failure Failure of a member is defined as one of two conditions. 1.Fracture of the material of which the member is made. This type of failure](https://reader036.vdocument.in/reader036/viewer/2022081511/56649f2a5503460f94c44a01/html5/thumbnails/17.jpg)
Problem 02
The state of plane stress shown occurs at a critical point of a steel
machine component. As a result of several tensile tests, it has been found
that the ten sile yield strength is y = 250 MPa for the grade of steel used.
Determine the factor of safety with respect to yield, using (a) the
maximum-shearing-stress criterion, and (b) the maximum-distortion-
energy criterion.
17
![Page 18: Theories of Failure Failure of a member is defined as one of two conditions. 1.Fracture of the material of which the member is made. This type of failure](https://reader036.vdocument.in/reader036/viewer/2022081511/56649f2a5503460f94c44a01/html5/thumbnails/18.jpg)
18
![Page 19: Theories of Failure Failure of a member is defined as one of two conditions. 1.Fracture of the material of which the member is made. This type of failure](https://reader036.vdocument.in/reader036/viewer/2022081511/56649f2a5503460f94c44a01/html5/thumbnails/19.jpg)
SOLUTION Mohr's Circle. We construct Mohr's circle for the given state of stress and find
MPaOC yxave 20)4080()( 21
21
MPaFXCFRm 65)25()60()()( 2222
Principal Stresses
MPaCAOCa 856520 MPaCAOCb 456520
a. Maximum-Shearing-Stress Criterion. Since for the grade of steel used
the tensile strength is ay = 250 MPa, the corresponding shearing stress at
yield is MPaMPaYY 125)250(2
121 19
![Page 20: Theories of Failure Failure of a member is defined as one of two conditions. 1.Fracture of the material of which the member is made. This type of failure](https://reader036.vdocument.in/reader036/viewer/2022081511/56649f2a5503460f94c44a01/html5/thumbnails/20.jpg)
MPaFor m 65 2.19.65
125. SF
MPa
MPaSF
m
Y
20
![Page 21: Theories of Failure Failure of a member is defined as one of two conditions. 1.Fracture of the material of which the member is made. This type of failure](https://reader036.vdocument.in/reader036/viewer/2022081511/56649f2a5503460f94c44a01/html5/thumbnails/21.jpg)
b. Maximum-Distortion-Energy Criterion. Introducing a factor of safety
into Eq. (7.26), we write
222
.
SFY
bbaa
For a = +85 MPa, b = -45 MPa, and y = 250 MPa, we have
2
22
.
25045458585
SF
19.2..
2503.114 SF
SF
21
![Page 22: Theories of Failure Failure of a member is defined as one of two conditions. 1.Fracture of the material of which the member is made. This type of failure](https://reader036.vdocument.in/reader036/viewer/2022081511/56649f2a5503460f94c44a01/html5/thumbnails/22.jpg)
Comment. For a ductile material with y = 250 MPa, we have drawn the
hexagon associated with the maximum-shearing-stress criterion and the
el lipse associated with the maximum-distortion-energy criterion. The
given state of plane stress is represented by point H of coordinates a =
85 MPa and b = -45 MPa. We note that the straight line drawn through
points O and H intersects the hexagon at point T and the ellipse at point
M. For each criterion, the value obtained for F.S. can be verified by
measuring the line segments in dicated and computing their ratios:
19.2.2.19. OH
OMSFb
OH
OTSFa 22
![Page 23: Theories of Failure Failure of a member is defined as one of two conditions. 1.Fracture of the material of which the member is made. This type of failure](https://reader036.vdocument.in/reader036/viewer/2022081511/56649f2a5503460f94c44a01/html5/thumbnails/23.jpg)
23
![Page 24: Theories of Failure Failure of a member is defined as one of two conditions. 1.Fracture of the material of which the member is made. This type of failure](https://reader036.vdocument.in/reader036/viewer/2022081511/56649f2a5503460f94c44a01/html5/thumbnails/24.jpg)
The solid shaft shown in Fig. 10-41a has a radius of 0.5 in. and is made
of steel having a yield stress of y = 36 ksi. Determine if the loadings
cause the shaft to fail according to the maximum-shear-stress theory
and the maximum-distortion-energy theory.
Example 10-12
Solution
The state of stress in the shaft is caused by both the axial force and the
torque. Since maximum shear stress caused by the torque occurs in the
material at the outer surface, we have
24
![Page 25: Theories of Failure Failure of a member is defined as one of two conditions. 1.Fracture of the material of which the member is made. This type of failure](https://reader036.vdocument.in/reader036/viewer/2022081511/56649f2a5503460f94c44a01/html5/thumbnails/25.jpg)
ksiin
ininkip
J
Tc
ksiin
kip
A
P
xy
x
55.162/.)5.0(
.)5.0.(.25.3
10.19.)5.0(
15
4
2
The stress components are shown acting on an element of material at
point A in Fig. 10-41b. Rather than using Mohr's circle, the principal
stresses can also be obtained using the stress-transformation equations,
Eq.9-5.
22
2,1
2
2
2,1
)55.16(2
010.19
2
010.19
22
xyyxyx
25
![Page 26: Theories of Failure Failure of a member is defined as one of two conditions. 1.Fracture of the material of which the member is made. This type of failure](https://reader036.vdocument.in/reader036/viewer/2022081511/56649f2a5503460f94c44a01/html5/thumbnails/26.jpg)
= -9.55 ± 19.11
CTI = 9.56 ksi
CT2 = -28.66 ksi
Maximum-Shear-Stress Theory. Since the principal stresses have
opposite signs, then from Sec. 9.5, the absolute maximum shear stress
will occur in the plane, and therefore, applying the second of Eq. 10-27,
we have
362.38
3666.2856.9?
21
Y
26
![Page 27: Theories of Failure Failure of a member is defined as one of two conditions. 1.Fracture of the material of which the member is made. This type of failure](https://reader036.vdocument.in/reader036/viewer/2022081511/56649f2a5503460f94c44a01/html5/thumbnails/27.jpg)
Thus, shear failure of the material will occur according to this theory.
Maximum-Distortion-Energy Theory. Applying Eq. 10-30, we have
Using this theory, failure will not occur.
12961187
)36(66.2866.2856.956.9
)(
2?
22
2221
21
y
27
![Page 28: Theories of Failure Failure of a member is defined as one of two conditions. 1.Fracture of the material of which the member is made. This type of failure](https://reader036.vdocument.in/reader036/viewer/2022081511/56649f2a5503460f94c44a01/html5/thumbnails/28.jpg)
Maximum Principal Stress theory or
(Rankine Theory)
According to this theory, it is assumed that when a member is
subjected to any state of stress, fails (fracture of brittle material or
yielding of ductile material) when the principal stress of largest
magnitude. (1) in the member reaches to a limiting value that is equal
to the ultimate normal stress, the material can sustain when subjected to
simple tension or compression.
The equations are shown graphically as
)1(1 ult )2(2 ult 28
![Page 29: Theories of Failure Failure of a member is defined as one of two conditions. 1.Fracture of the material of which the member is made. This type of failure](https://reader036.vdocument.in/reader036/viewer/2022081511/56649f2a5503460f94c44a01/html5/thumbnails/29.jpg)
ult
These equations are shown graphically if the point obtained by plotting
the values of 1 + 2 falls within the square area the member is safe.29
![Page 30: Theories of Failure Failure of a member is defined as one of two conditions. 1.Fracture of the material of which the member is made. This type of failure](https://reader036.vdocument.in/reader036/viewer/2022081511/56649f2a5503460f94c44a01/html5/thumbnails/30.jpg)
It can be seen that stress co-ordinate 1 and 2 at a point in the material
falls on the boundary for outside the shaded area, the material is said to
be fractured failed. Experimentally, it has been found to be in close
agreement with the behavior of brittle material that have stress-strain
diagram similar in both tension and compression. It cab be further
noticed that in first and third quad, the boundary is the save as for
maximum shear stress theory.
Problem
A thin-walled cylindrical pressure vessel is subject to an internal
pressure of 600 lb/in2. the mean radius of the cylinder is 15in. If the
material ha a yield point of 39,000lb/in2 and a safety of 3 is employed, 30
![Page 31: Theories of Failure Failure of a member is defined as one of two conditions. 1.Fracture of the material of which the member is made. This type of failure](https://reader036.vdocument.in/reader036/viewer/2022081511/56649f2a5503460f94c44a01/html5/thumbnails/31.jpg)
determine the required wall thickness using (a) the maximum normal
stress theory, and (b) the Huber-von Mises-Hencky theory.
P = 600psi.
r = 15"
y = 39000psi
F.O.S = 3
t = ?
According to
c Circumferential stress / girth stress
where
Pr
tc
31
![Page 32: Theories of Failure Failure of a member is defined as one of two conditions. 1.Fracture of the material of which the member is made. This type of failure](https://reader036.vdocument.in/reader036/viewer/2022081511/56649f2a5503460f94c44a01/html5/thumbnails/32.jpg)
By comparing 1 = c.
Thus, According to the normal stress theory, maximum Principal stress
should be equal to yield stress/FOS i.e.
|1| ≤ ult |2| ≤ ult
f = maximum (|1|, |2|, |3| - ult = 0)
tt
t
stressallengitudinFor
tt
c
l
c
4500
2
"15600
2
Pr
9000"15600
32
![Page 33: Theories of Failure Failure of a member is defined as one of two conditions. 1.Fracture of the material of which the member is made. This type of failure](https://reader036.vdocument.in/reader036/viewer/2022081511/56649f2a5503460f94c44a01/html5/thumbnails/33.jpg)
As y = 39000psi
.69.0
900013000
9000
3
39000
Anst
t
t
Problem 02:-
The solid circular shaft in Fig. 18-12(a) is subject to belt pulls at
each end and is simply supported at the two bearings. The material has
a yield point of 36,000 Ib/in2• Determine the required diameter of the
shaft using the maximum normal stress theory together with a safety
factor of 3. 33
![Page 34: Theories of Failure Failure of a member is defined as one of two conditions. 1.Fracture of the material of which the member is made. This type of failure](https://reader036.vdocument.in/reader036/viewer/2022081511/56649f2a5503460f94c44a01/html5/thumbnails/34.jpg)
400 + 200 lb200 + 500 lb
34
![Page 35: Theories of Failure Failure of a member is defined as one of two conditions. 1.Fracture of the material of which the member is made. This type of failure](https://reader036.vdocument.in/reader036/viewer/2022081511/56649f2a5503460f94c44a01/html5/thumbnails/35.jpg)
35
![Page 36: Theories of Failure Failure of a member is defined as one of two conditions. 1.Fracture of the material of which the member is made. This type of failure](https://reader036.vdocument.in/reader036/viewer/2022081511/56649f2a5503460f94c44a01/html5/thumbnails/36.jpg)
0
42800
64
24200
.42006700
.36006600
64
2
3
4
4
y
x
x
B
x
d
d
d
inlbMc
inlbM
dI
dc
I
Mc
36
![Page 37: Theories of Failure Failure of a member is defined as one of two conditions. 1.Fracture of the material of which the member is made. This type of failure](https://reader036.vdocument.in/reader036/viewer/2022081511/56649f2a5503460f94c44a01/html5/thumbnails/37.jpg)
inlb
OR
inlb
T
d
d
d
J
Tr
xy
xy
.480024200
24)200400(
.480016300
16)200500(
480,24
32
24800
3
4
xyyx
yxxy
3
480,24
dxy 3
800,42
dx
x
37
![Page 38: Theories of Failure Failure of a member is defined as one of two conditions. 1.Fracture of the material of which the member is made. This type of failure](https://reader036.vdocument.in/reader036/viewer/2022081511/56649f2a5503460f94c44a01/html5/thumbnails/38.jpg)
2
2
2
2
2
1
22
22
xyyxyx
xyyxyx
2
3
2
331
20.24446
2
42800
2
42800
ddd
According to maximum normal stress theory .
2
3
2
33
1
20.24446
2
42800
2
42800
3
36000
ddd
ult
38
![Page 39: Theories of Failure Failure of a member is defined as one of two conditions. 1.Fracture of the material of which the member is made. This type of failure](https://reader036.vdocument.in/reader036/viewer/2022081511/56649f2a5503460f94c44a01/html5/thumbnails/39.jpg)
"48.1
51.10
10514.110144
1062.5971096.457
2
1092.91510144
20.24446
2
42800
2
4280012000
6
6
96
6
6
6
6
3
66
2
3
2
33
d
d
d
ddd
ddd
39
![Page 40: Theories of Failure Failure of a member is defined as one of two conditions. 1.Fracture of the material of which the member is made. This type of failure](https://reader036.vdocument.in/reader036/viewer/2022081511/56649f2a5503460f94c44a01/html5/thumbnails/40.jpg)
Mohr’s Criterion:-
In some material such as cast iron, have much greater strength
in compression than tension so Mohr proposed that is 1st and third
quadrant of a failure brokes, a maximum principal stress theory was
appropriate based on the ultimate strength of materials in tension or
compression. Therefore in 2nd and 4th quad, where the maximum shear
stress theory should apply.
Pure shear is one in which x and y are equal but of opposite sense.
40
![Page 41: Theories of Failure Failure of a member is defined as one of two conditions. 1.Fracture of the material of which the member is made. This type of failure](https://reader036.vdocument.in/reader036/viewer/2022081511/56649f2a5503460f94c44a01/html5/thumbnails/41.jpg)
cult
Failure or strength envelope
Pure shear
Smaller tension strength
Largest compressive strength
41
![Page 42: Theories of Failure Failure of a member is defined as one of two conditions. 1.Fracture of the material of which the member is made. This type of failure](https://reader036.vdocument.in/reader036/viewer/2022081511/56649f2a5503460f94c44a01/html5/thumbnails/42.jpg)
tension
compression
42
![Page 43: Theories of Failure Failure of a member is defined as one of two conditions. 1.Fracture of the material of which the member is made. This type of failure](https://reader036.vdocument.in/reader036/viewer/2022081511/56649f2a5503460f94c44a01/html5/thumbnails/43.jpg)
Problem 3:-
In a cast-iron component the maximum principal stress is to be limited
to one-third of the tensile strength . Determine the maximum value of
the minimum principal stresses ,using the Mohr theory. What would be
the values of the principal stresses "associated with a maximum shear
stress of 390 MN/m2? The tensile and compressive strengths of the cast
iron are 360 MN/m2 and 1.41 GN/m2 respectively
43
![Page 44: Theories of Failure Failure of a member is defined as one of two conditions. 1.Fracture of the material of which the member is made. This type of failure](https://reader036.vdocument.in/reader036/viewer/2022081511/56649f2a5503460f94c44a01/html5/thumbnails/44.jpg)
stress Shearingfourthand2
stress Normalquadrant thirdand1
criterionsMohr'perAs
?
nd
st
2
quadrant
2
)(1
/1203
360
3
thatindicatedAs
mMN
tult
26
2
/101414
/360
mMN
mMN
cult
tult
44
![Page 45: Theories of Failure Failure of a member is defined as one of two conditions. 1.Fracture of the material of which the member is made. This type of failure](https://reader036.vdocument.in/reader036/viewer/2022081511/56649f2a5503460f94c44a01/html5/thumbnails/45.jpg)
By using principal stress theory
2
2
2
1
/414
/360
)(
)(
mMN
mMNAs
b
a
cult
tult
ult
ult
21 /120 mMN
Maximum principal stress = 360/3 = 120 MN/m2 (tension). According
to Mohr's theory, in the second and fourth quadrant
From (a) and (b) 45
![Page 46: Theories of Failure Failure of a member is defined as one of two conditions. 1.Fracture of the material of which the member is made. This type of failure](https://reader036.vdocument.in/reader036/viewer/2022081511/56649f2a5503460f94c44a01/html5/thumbnails/46.jpg)
Therefore
22
2 /94011410360
120mMNand
The Mohr's stress circle construction for the second part of this problem
is shown in Fig. 13.7. If the maximum shear stress is 390 MN/m2, a
circle is drawn of radius 390 units to touch the two envelope lines. The
principal stresses can then be read off as +200 MN/m2 and -580
MN/m2•
1
11
21
21
culttult
culttult
and
46
![Page 47: Theories of Failure Failure of a member is defined as one of two conditions. 1.Fracture of the material of which the member is made. This type of failure](https://reader036.vdocument.in/reader036/viewer/2022081511/56649f2a5503460f94c44a01/html5/thumbnails/47.jpg)
cult tult
360tult1410cult
390max
47
![Page 48: Theories of Failure Failure of a member is defined as one of two conditions. 1.Fracture of the material of which the member is made. This type of failure](https://reader036.vdocument.in/reader036/viewer/2022081511/56649f2a5503460f94c44a01/html5/thumbnails/48.jpg)
Fig 13.7 48
![Page 49: Theories of Failure Failure of a member is defined as one of two conditions. 1.Fracture of the material of which the member is made. This type of failure](https://reader036.vdocument.in/reader036/viewer/2022081511/56649f2a5503460f94c44a01/html5/thumbnails/49.jpg)
Now from second state
21
21max
21
21
21cult
21tult
2max
2
2
1414
380
quadfourth in and
theorystress shearingBy
/390
R
Also
Thus
mMN
49
![Page 50: Theories of Failure Failure of a member is defined as one of two conditions. 1.Fracture of the material of which the member is made. This type of failure](https://reader036.vdocument.in/reader036/viewer/2022081511/56649f2a5503460f94c44a01/html5/thumbnails/50.jpg)
Example 10-11
The solid cast-iron shaft shown in Fig. 10-40a is subjected to a torque
of T = 400 Ib . ft. Determine its smallest radius so that it does not fail
according to the maximum-normal-stress theory. A specimen of cast
iron, tested in tension, has an ultimate stress of (σult)t = 20 ksi.
Solution
The maximum or critical stress occurs at a point located on the surface
of the shaft. Assuming the shaft to have a radius r, the shear stress is
34max
..8.055
)2/(
)/.12)(.400(
r
inlb
r
rftinftlb
J
Tc
50
![Page 51: Theories of Failure Failure of a member is defined as one of two conditions. 1.Fracture of the material of which the member is made. This type of failure](https://reader036.vdocument.in/reader036/viewer/2022081511/56649f2a5503460f94c44a01/html5/thumbnails/51.jpg)
51
![Page 52: Theories of Failure Failure of a member is defined as one of two conditions. 1.Fracture of the material of which the member is made. This type of failure](https://reader036.vdocument.in/reader036/viewer/2022081511/56649f2a5503460f94c44a01/html5/thumbnails/52.jpg)
52
![Page 53: Theories of Failure Failure of a member is defined as one of two conditions. 1.Fracture of the material of which the member is made. This type of failure](https://reader036.vdocument.in/reader036/viewer/2022081511/56649f2a5503460f94c44a01/html5/thumbnails/53.jpg)
Mohr's circle for this state of stress (pure shear) is shown in Fig. 10-
40b. Since R = max, then
The maximum-normal-stress theory, Eq. 10-31, requires
|1| ≤ ult
3max21
..8.3055
r
inlb
23
/000,20..8.3055
inlbr
inlb
Thus, the smallest radius of the shaft is determined from
..535.0
/000,20..8.3055 2
3
Ansinr
inlbr
inlb
53
![Page 54: Theories of Failure Failure of a member is defined as one of two conditions. 1.Fracture of the material of which the member is made. This type of failure](https://reader036.vdocument.in/reader036/viewer/2022081511/56649f2a5503460f94c44a01/html5/thumbnails/54.jpg)
The solid shaft shown in Fig. 10-41a has a radius of 0.5 in. and is made
of steel having a yield stress of y = 36 ksi. Determine if the loadings
cause the shaft to fail according to the maximum-shear-stress theory
and the maximum-distortion-energy theory.
Example 10-12
Solution
The state of stress in the shaft is caused by both the axial force and the
torque. Since maximum shear stress caused by the torque occurs in the
material at the outer surface, we have
54
![Page 55: Theories of Failure Failure of a member is defined as one of two conditions. 1.Fracture of the material of which the member is made. This type of failure](https://reader036.vdocument.in/reader036/viewer/2022081511/56649f2a5503460f94c44a01/html5/thumbnails/55.jpg)
ksiin
ininkip
J
Tc
ksiin
kip
A
P
xy
x
55.162/.)5.0(
.)5.0.(.25.3
10.19.)5.0(
15
4
2
The stress components are shown acting on an element of material at
point A in Fig. 10-41b. Rather than using Mohr's circle, the principal
stresses can also be obtained using the stress-transformation equations,
Eq.9-5.
22
2,1
2
2
2,1
)55.16(2
010.19
2
010.19
22
xyyxyx
55
![Page 56: Theories of Failure Failure of a member is defined as one of two conditions. 1.Fracture of the material of which the member is made. This type of failure](https://reader036.vdocument.in/reader036/viewer/2022081511/56649f2a5503460f94c44a01/html5/thumbnails/56.jpg)
= -9.55 ± 19.11
CTI = 9.56 ksi
CT2 = -28.66 ksi
Maximum-Shear-Stress Theory. Since the principal stresses have
opposite signs, then from Sec. 9.5, the absolute maximum shear stress
will occur in the plane, and therefore, applying the second of Eq. 10-27,
we have
362.38
3666.2856.9?
21
Y
56
![Page 57: Theories of Failure Failure of a member is defined as one of two conditions. 1.Fracture of the material of which the member is made. This type of failure](https://reader036.vdocument.in/reader036/viewer/2022081511/56649f2a5503460f94c44a01/html5/thumbnails/57.jpg)
Thus, shear failure of the material will occur according to this theory.
Maximum-Distortion-Energy Theory. Applying Eq. 10-30, we have
Using this theory, failure will not occur.
12961187
)36(66.2866.2856.956.9
)(
2?
22
2221
21
y
57
![Page 58: Theories of Failure Failure of a member is defined as one of two conditions. 1.Fracture of the material of which the member is made. This type of failure](https://reader036.vdocument.in/reader036/viewer/2022081511/56649f2a5503460f94c44a01/html5/thumbnails/58.jpg)
Maximum Normal Strain or Saint Venant’s
Criterion
In this theory, it is assumed that a member subjected to any state of
stress fails (yields) when the maximum normal strain at any point
equals, the yield point strain obtained from a simple tension or
compression test (y = σy/).
Principal strain of largest magnitude |max| could be one of two
principal strain 1 and 2 depending upon the stress conditions acting in
the member . Thus the maximum Principal strain theory may be
represented by the following equation.58
![Page 59: Theories of Failure Failure of a member is defined as one of two conditions. 1.Fracture of the material of which the member is made. This type of failure](https://reader036.vdocument.in/reader036/viewer/2022081511/56649f2a5503460f94c44a01/html5/thumbnails/59.jpg)
)1(2max
1max
y
y
As stress in one direction produces the lateral deformation in the other
two perpendicular directions and using law of superposition, we find
three principal strains of the element.
x=
y=
z=
σx
σx / E
-μσx / E
-μσx / E
σy
μσy / E
σy / E
-μσy / E
σz
–μσz / E
-μσz / E
σz / E
x=
y=
z=
x=
y=
z= 59
![Page 60: Theories of Failure Failure of a member is defined as one of two conditions. 1.Fracture of the material of which the member is made. This type of failure](https://reader036.vdocument.in/reader036/viewer/2022081511/56649f2a5503460f94c44a01/html5/thumbnails/60.jpg)
x = σx / E -μσy / E -μσz / E
= σx / E -μ / E (σy + σz)
y = σy / E -μσx / E -μσz / E
= σy / E -μ / E (σx + σz)
z = σz / E -μσy / E -μσx / E
= σz / E -μ / E (σx + σy)
(2)
Thus
)3(
)(
)(
)(
123
3
312
2
321
1
EE
EE
EE
60
![Page 61: Theories of Failure Failure of a member is defined as one of two conditions. 1.Fracture of the material of which the member is made. This type of failure](https://reader036.vdocument.in/reader036/viewer/2022081511/56649f2a5503460f94c44a01/html5/thumbnails/61.jpg)
Also
)6(
)5(
Then
and
4and1Equating
)4()2(
12y
21y
122
21
1
211
EE
EEE
dForEE
y
y
61
![Page 62: Theories of Failure Failure of a member is defined as one of two conditions. 1.Fracture of the material of which the member is made. This type of failure](https://reader036.vdocument.in/reader036/viewer/2022081511/56649f2a5503460f94c44a01/html5/thumbnails/62.jpg)
The yield surface ABCD is the straight under biaxial tension or biaxial
compression Individual principal stresses greater than σy can occur
without causing yielding.
62
![Page 63: Theories of Failure Failure of a member is defined as one of two conditions. 1.Fracture of the material of which the member is made. This type of failure](https://reader036.vdocument.in/reader036/viewer/2022081511/56649f2a5503460f94c44a01/html5/thumbnails/63.jpg)
Maximum Shear Strain Energy (Distortion
Energy Criterion (Von MISES Criterion)
According to this theory when a member is subjected to any state of
stress fails (yields) when the distortion energy per unit volume at a
point becomes equal to the strain energy of distortion per unit volume
at failure (yielding) in uniaxial tension (or compression).
The distortion strain energy is that energy associated with a change in
the shape of the body.
The total strain energy per unit volume also called strain energy
density is the energy in a body stored internally throughout its volume
due to deformation produced by external loading. If the axial stress63
![Page 64: Theories of Failure Failure of a member is defined as one of two conditions. 1.Fracture of the material of which the member is made. This type of failure](https://reader036.vdocument.in/reader036/viewer/2022081511/56649f2a5503460f94c44a01/html5/thumbnails/64.jpg)
arising in a tension test is “” and the corresponding axial strain is ε
then the work done or a unit volume of the test specimen is the product
of mean value of the force per unit area (/2) times the displacement in
the direction of the force, or ε. The work is thus
)1(2
U
This work is stored as internal strain energy.
When an elastic element subjected to triaxial loading as show in Fig the
stresses can be resolves in to three principal stresses σ1,σ2 and σ3. where
1,2 and 3 are the principal axes. These three principal stresses will be
accompanied by these principal strain related to the stresses by
equations 3,4and 564
![Page 65: Theories of Failure Failure of a member is defined as one of two conditions. 1.Fracture of the material of which the member is made. This type of failure](https://reader036.vdocument.in/reader036/viewer/2022081511/56649f2a5503460f94c44a01/html5/thumbnails/65.jpg)
If it is assumed that loads are applied gradually and simultaneous then
stresses and strain will increase in the same manner. The total strain
energy per unit volume in the sum of energies produced by each of the
stresses (as energy is a scalar quantity )
E
u
E
)( 3211
E
u
E
)( 3122
E
u
E
)( 2133
(2)
(3)
(4)
65
![Page 66: Theories of Failure Failure of a member is defined as one of two conditions. 1.Fracture of the material of which the member is made. This type of failure](https://reader036.vdocument.in/reader036/viewer/2022081511/56649f2a5503460f94c44a01/html5/thumbnails/66.jpg)
Where ε1, ε2, and ε3, are the normal strain in the direction of principal
stresses respectively of strain are expressed in term of stresses than
equation (5) taken the following form
)5(,2
1,,
2
1,,
2
13322 U
EEEEEEEEEU 213
3312
2321
1 2
1
2
1)(
2
1
Which can be reduced to
)6()(22
1323121
33
22
21
EU
66
![Page 67: Theories of Failure Failure of a member is defined as one of two conditions. 1.Fracture of the material of which the member is made. This type of failure](https://reader036.vdocument.in/reader036/viewer/2022081511/56649f2a5503460f94c44a01/html5/thumbnails/67.jpg)
As the deformation of a material can be separated in to two parts
(a) Change in volume, (b) change in shape or distortion.
Similarly the total strain energy can be broken in to two parts. One part
representing the energy needed to cause volume change of the element
with no change in shape (Uv) and the other part representing the energy
needed to distort the element (Ud).
)7(dv UUU
The principal stresses σ1,σ2 and σ3 of Fig. (01) can be resolved in to two
states of stresses in Fig. (02) b & c. the state of stress shown in Fig. b
represents a hydrostatic stress condition in which all these principal
stress are equal to the quantity σ. 67
![Page 68: Theories of Failure Failure of a member is defined as one of two conditions. 1.Fracture of the material of which the member is made. This type of failure](https://reader036.vdocument.in/reader036/viewer/2022081511/56649f2a5503460f94c44a01/html5/thumbnails/68.jpg)
1
3
1
(a)
(b)
1-
3-
2-
(c)
68
![Page 69: Theories of Failure Failure of a member is defined as one of two conditions. 1.Fracture of the material of which the member is made. This type of failure](https://reader036.vdocument.in/reader036/viewer/2022081511/56649f2a5503460f94c44a01/html5/thumbnails/69.jpg)
Some materials were subjected to hydrostatic pressure resulting in
appreciable changes in volume but no change in shape and no failure by
yielding. Therefore the remaining portion of the stress (1 - ), (2 - )
and (3 - ) will result in distortion only (No volume change) and the
algebraic sum of the three principal strains produced by the three
principal stresses (1 - ave), (2 - ave) and (3 - ave) must be equal to
zero. i.e (ε1+ε2+ε3)d=0 (9)
Expressing strains in term of stresses.
69
![Page 70: Theories of Failure Failure of a member is defined as one of two conditions. 1.Fracture of the material of which the member is made. This type of failure](https://reader036.vdocument.in/reader036/viewer/2022081511/56649f2a5503460f94c44a01/html5/thumbnails/70.jpg)
0213
132
321321
dE
2
2
2
213
132
321
2
22
213
132321
63333222111
63222 332211
70
![Page 71: Theories of Failure Failure of a member is defined as one of two conditions. 1.Fracture of the material of which the member is made. This type of failure](https://reader036.vdocument.in/reader036/viewer/2022081511/56649f2a5503460f94c44a01/html5/thumbnails/71.jpg)
a) One part that causes Volumetric (Uv)
b) Change and one causes distortion an (Ud)
)4(dv UUU
a) As according to theory of distortion only energy due to
distortion is responsible for failure. Some experimental
evidence supports this assumption some materials were
subjected to hydrostatic pressure result in appreciable changes
in volume but no change in shape and no failure by yielding.
The hydrostatic pressure is the average of three principal
stresses 1 2 and 3 known as average stress. )5(
3321
max
71
![Page 72: Theories of Failure Failure of a member is defined as one of two conditions. 1.Fracture of the material of which the member is made. This type of failure](https://reader036.vdocument.in/reader036/viewer/2022081511/56649f2a5503460f94c44a01/html5/thumbnails/72.jpg)
This principal strains ε in the material.
Due to there Principal stresses (1, 2, 3) three principal strains ε1, ε2,
and ε3, are produced. The state of stress in Fig below will result in
distortion only (No volume change) if sum of three normal strains is
zero. That is
)6(0
2
221)(
213
3123221321
u
EE
Which eh reduces to
)5(3/
03)21(
321
321
72
![Page 73: Theories of Failure Failure of a member is defined as one of two conditions. 1.Fracture of the material of which the member is made. This type of failure](https://reader036.vdocument.in/reader036/viewer/2022081511/56649f2a5503460f94c44a01/html5/thumbnails/73.jpg)
The normal strains corresponding to these stresses are found from three
dimension from of Hook’s law given by the following equation.
)7()21(E
Strain energy resulting from these stresses or strains can be obtained by
subject through these values is
)8(.2
3.
2
1.
2
1.
2
1
, 321321
Uv
73
![Page 74: Theories of Failure Failure of a member is defined as one of two conditions. 1.Fracture of the material of which the member is made. This type of failure](https://reader036.vdocument.in/reader036/viewer/2022081511/56649f2a5503460f94c44a01/html5/thumbnails/74.jpg)
(5)3
)()21(
3
)(.
2
3 321321
E
uU v
2321 )(
6
)21(
E
uU v (9)
Strain energy due to distortion
U=Uy + Ud
Ud = U- Uy
2321323121
23
22
21 6
212
2
1 E
uu
EU d
(10)
2321323121
23
22
21 21)(6)(3
6
1 uuE
U d74
![Page 75: Theories of Failure Failure of a member is defined as one of two conditions. 1.Fracture of the material of which the member is made. This type of failure](https://reader036.vdocument.in/reader036/viewer/2022081511/56649f2a5503460f94c44a01/html5/thumbnails/75.jpg)
When the third force in the
2113
23
2332
22
2221
21 222
6
1
E
uU d
213
232
2216
1
E
uU d
(12)
(13)
For biaxial stress system, σ3 = 0
2221
21 2
3
1
E
uU d
(14)
For uniaxial stress system
213
1 E
uU d
(15)
75
![Page 76: Theories of Failure Failure of a member is defined as one of two conditions. 1.Fracture of the material of which the member is made. This type of failure](https://reader036.vdocument.in/reader036/viewer/2022081511/56649f2a5503460f94c44a01/html5/thumbnails/76.jpg)
For Distortion theory the failure occurs when distortion energy of the
member however equal to the strain energy of distortion at failure
(yielding) in uniaxial torsion (or equilibrium). So substituting σ1=σy in
equ (15)
226
1yd E
uU
(16)
And equating it with (13)
213
232
221
2
6
1)2(
6
1
E
u
E
uy
213
232
221
22 y (17) 76
![Page 77: Theories of Failure Failure of a member is defined as one of two conditions. 1.Fracture of the material of which the member is made. This type of failure](https://reader036.vdocument.in/reader036/viewer/2022081511/56649f2a5503460f94c44a01/html5/thumbnails/77.jpg)
For biaxial stress system
2221
21
2 2 y (18)
77