®

INSTALLATION, OPERATION, & MAINTENANCE MANUAL

1000D & 1000D-XLTMOTORCYCLE / ATV LIFT

FOLLOW THIS MANUAL CAREFULLY TO ENSURE THE MACHINE WILL FUNCTION CORRECTLY AND PROVIDE MANY YEARS OF DEPENDABLE SERVICE. FAILURE TO FOLLOW THESE INSTRUCTIONS AND SAFETY WARNINGS MAY RESULT IN PERSONAL INJURY OR PROPERTY DAMAGE. USE OF STRAPS IS RECOMMENDED - SOLD SEPARATELY. KEEP THIS MANUAL IN A SAFE DRY PLACE FOR FUTURE REFERENCE.

1

To Our Valued Customers:

Thank you for purchasing a Titan Lifts® product. We hope this high quality equipment provides you with years of dependable service.

It is unfortunate that rare situations may occur with the products you purchase from Titan Lifts®. We value your business as well as the trust you have and need to maintain your relationship with us. Titan Lifts® carries liability coverage that may protect our customers if a situation does occur. However, as in all accidents there must be proof of liability for a claim to be made. Our insurance company requires the following procedures be observed in order to consider a claim:

A. The claimant must contact the Titan Lifts® distributor immediately with the facts of the situation. B. If any equipment is damaged, including vehicles or shop equipment, Titan Lifts® must be given the opportunity to send and impartial representative to the site for proper assessment of the situation. C. The Vehicle cannot be moved until either an impartial representative has reviewed the accident or clear and precise pictures are taken that reflect all the pertinent information for an impartial representative to be able to access the information from a distance. Titan Lifts® or its representatives must approve the pictures before anything can be moved. D. If any potential liability is determined on behalf of Titan Lifts®, two estimates must be submitted for damages to be reimbursed.

It is imperative that the claimant complies with these procedures, because without proper assessment of the situ-ation a claim will be denied.

ARBITRATION NOTICEThe installation or use of this equipment shall constitute an acknowledgement that the user agrees to resolve any and all disputes or claims of any kind whatsoever, which relate in any way to the equipment, by way of binding arbitration, not litigation. No suit or legal action may be filed in any state or federal court. Any arbitration shall be governed by the Federal Arbitration Act, and administered by the American Mediation Association, Indianapolis Indiana. The maximum amount that an arbitrator may award and all damages shall not exceed the retail value of this equipment.

WARRANTY NOTICEThis equipment must be installed be a “Professional Installer” assembled and used in the manner according to the documentation provided to be covered by warranty.

Damaged or missing components must be reported within 72 hours of receipt to your freight carrier and to the distributor. Claims must be filed to cover cost.

If you have any questions or if we can be of any further assistance, please don’t hesitate to contact a Titan Lifts® representative at 1-888-908-4826. Thank you for the opportunity to continue to serve your lift equipment needs.

®

PO Box 7069 Greenwood, IN 461421.888.908-4826 FAX (317) 215.2770

www.titanlifts.com

TITAN MARKETING, LLC

22 3

INSTRUCTIONS WARNING: READ ENTIRE MANUAL AND COMPLY WITH ALL SAFETY AND SERVICE PRECAUTIONS. DEATH, PERSONAL INJURY AND / OR PROPERTY DAMAGE MAY OCCUR IF INSTRUCTIONS ARE NOT FOLLOWED CAREFULLY.

UNPACKING AND SET-UP *REFER TO PARTS LIST FIG. 11. Carefully unpack the lift making sure that all of the parts have been included.2. Remove the lift and all parts from delivery pallet and place on a clean, solid flat surface.3. Safely, manually lift the deck plate (57) so that the safety bar (46) sits within the first safety latch. It is recommended at least two people perform this function. 4. XLT ONLY: Remove one of the stabilization pipe caps (26) from the stabilization bar (27). Slide the stabilization bar through the square tubing of the back lifting arm (28) and place the stabilization cap back on the end. Secure the stabilization bar in place with the steel ball pins (25).5. If using the front extension (55), slide the front extension over the front of the deck plate so that the support pipe holes align. Hold the front extension in place by connecting the Eye Bolts (56) with a Washer Φ10 (23) and Nut M10 (24).6. Take the fixed clamp (63) and bolt it to the deck plate (57) or front extension (55) using the provided bolts (64), Washers Φ10 (23) and Nuts M10 (24). Insert the tire stop (61) onto the fixed clamp using the pin (62).7. Take the movable clamp (60) and bolt it to the deck plate (57) or front extension (55) using the provided bolts (64.1), Washers Φ10 (23) and Nuts M10 (24).8. If using the side extensions (52), slide the support pipes (53) through support pipe holes in the front and rear of the deck plate (57). Slide the side extensions over the support pipes and secure in place with the quick pins (54).9. Hook the ramp (58) and extension panels (51) onto the back of the deck plate (57) and side extensions (52).10. Take ends of air hose (2) and attach to foot operated air valve (1) and the front cover (6) of the cylinder.11. Attach compressed air to the foot operated air valve (1) and raise the lift by moving the valve to the up position. Requires 70-90PSI.

Note: Standard dropout plate (59) can be removed for easy rear wheel removal.

Note: Roller dropout plate can be installed after motorcycle is loaded for easy rear wheel cleaning or maintenance. WARNING: Roller dropout plate must be removed prior to unloading the motorcycle from the lift & replaced with the standard dropout.

22 3

OPERATION & MAINTENANCE *REFER TO PARTS LIST FIG. 1

* Test the lift several times for proper operation before attempting to lift a load.

1. All moving parts have been lubricated at the factory and should be re-lubricated before the first use and at least once every six months to prevent damage. Grease fittings are located at each frame pivot shaft and at the top ends of the inside frame assembly.2. Lightly oil cylinder rod at least once every six months or when it becomes dry.3. Squirt some oil through the bleed hole in the plate at the end of the cylinder to lubricate piston and seal every six months.4. The pivot shaft set screws should be checked frequently to be sure they are tight. These are located at the top end of the inside frame assembly.5. Do not use this product if worn or damaged. Examine lift for structural cracks, bends, or other signs of damage prior to each use. Check all hoses and connections before each use to ensure proper working condition.6. Keep lift clean, dry, and well maintained to extend longevity of the product.7. Roll motorcycle onto deck plate (57) until wheel is inside the clamp (60 & 63).8. Tighten the clamp to the tire by using the crank handle on the moveable clamp (60).9. Load must be centered on the table at all times.10. Load must be firmly positioned and secured on the table at all times.11. To raise the lift, make sure that the compressed air is connected and use the foot operated air valve (1) until you reach the desired working height.12. IMPORTANT: After reaching the desired working height, lower the lift so that the safety bar (46) sits firmly in the safety latch and all pressure is off of the cylinder (20). Remove air supply from foot operated air valve (1).13. When finished working, attach air supply to foot operated air valve (1), raise the lift to release the safety bar (46) and place it back into deck plate (57). Slowly release the air from the cylinder (20) until the lift rests gently on the ground.

WARNING: Do not load the motorcycle onto deck plate (57) with the roller dropout installed.

WARNING: The safety bar (46) should be down securely in the safety lock when the lift is in the raised position so that the lift does not lower.

WARNINGThe warnings, precautions and instructions in this manual cannot cover all possible conditions and situations that may occur. The operator must understand that the operator must supply common sense and examine caution factors when using this product to determine safety in all circumstances being used.

44 5

SAFETY PRECAUTIONS1. Load should not exceed rated capacity for this lift - 1000lbs2. 70-90PSI shop air needed. Do NOT exceed the 100PSI capacity.3. Make sure the safety bar is down in the locked position while the lift is in the raised position.4. Move the lift only when it is lowered.5. Do not ride vehicle onto lift.6. Only trained people should operate the lift.7. Foot operated air valve should be at least 3 feet away when operating. Remain clear of the lift when raising or lowering.8. Indoor use recommended.9. Do not move lift while loaded.10. Keep hands, tools and other extremities from under carriage and moving parts.11. Maintain a safe working environment. The work area should be clean, dry, clutter free and sufficiently lit.12. Wear proper ANSI-approved safety attire. Do not wear loose fitting clothing while operating lift. Long hair and sleeves should be secured.13. Keep children and bystanders away from work area. Do not let children operate or play on lift.14. Do not use if under the influence of drugs or alcohol. Operator must be alert at all times when using heavy lift equipment.15. Never operate the lift with someone on it.16. Use this lift only for the work it is intended. Do not use this product for an application for which it was not designed. Misuse can lead to personal injury and/or property damage. 17. Industrial applications must follow OSHA requirements. 18. Do not use for aircraft purposes. 19. Have your lift serviced by a qualified repair person using only identical Titan Lifts® replacement parts and attachments. This will ensure that the safety of the lift is maintained.

PLEASE READ THE FOLLOWING CAREFULLYTHE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND ASSEMBLY DIAGRAM IN THIS MANUAL AS A REFERENCE TOOL ONLY. THE MANUFACTURER OR DISTRIBUTOR DOES NOT MAKE ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT, OR THAT HE OR SHE IS QUALIFIED TO REPLACE ANY PARTS OF THE PRODUCT. THE MANUFACTURER AND/OR DISTRIBUTOR EXPRESSLY STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE PERFORMED BY CERTIFIED AND LICENSED TECHNICIANS, AND NOT BY THE BUYER. THE BUYER ASSUMES ALL RISK AND LIABILITY ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS THERETO, OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO.Product’s Serial Number:____________________________________________________________________Note: If product does not have a serial number, record the month and year of purchase instead.Note: Some parts are listed and shown for illustration purposes only, and are not available individually as replacement parts.

44 5

FRONT WHEEL CLAMPINSTALLATION DRAWING

FRONT EXTENSION INSTALLATION DRAWING

60

63

61

56

55

56

23

57

24

63

6062

66 7

SIDE EXTENSIONSINSTALLATION DRAWING

52

51

58

54

53

27

52

53

54

52

51

53

51

27

25

26

66 7

PARTS LIST (FIG. 1)PLEASE MAKE SURE TO CONFIRM THAT ALL PARTS ARE INCLUDED.

(See Fig. 2)

(See Fig. 3).

88 9

PARTS LIST CON’T. (FIG. 1)NO. DESCRIPTION QTY NO DESCRIPTION QTY

1 FOOT OPERATED AIR VALVE (See Fig. 2) 1 43 SAFETY BAR HANDLE 22 AIR HOSE 1 44 PIN 23 SCREW CAP M10 4 45 R-PIN 24 WASHER Φ10 8 46 SAFETY BAR 15 NUT 1 47 MACHINE BOLT 26 FRONT COVER 1 48 PIN 27 NYLON O-RING 2 49 CYLINDER PIVOT SHAFT 18 O-RING 1 50 RETAINING RING 29 O-RING 2 51 RIGHT EXTENSION RAMP 2

10 SHAFT BUSHING 1 52 SIDE EXTENSION 211 PISTON ROD 1 53 SUPPORT PIPE 212 RETAINING RING 1 54 QUICK PIN 413 PRESS RING 1 55 FRONT EXTENSION 114 O-RING 1 56 EYE BOLT 215 PLASTIC O-RING 1 57 DECK PLATE 116 O-RING 1 58 MAIN RAMP 117 O-RING 1 59 DROP OUT COVER 118 PISTON 1 60 MOVABLE CLAMP 119 BOLT 1 61 TIRE STOP 120 CYLINDER 1 62 WHEEL STOP PIN 121 STAY BOLT 4 63 FIXED CLAMP 122 CYLINDER END PLATE 1 64 BOLT 18mm 623 WASHER Φ10 12 64.1 BOLT 25mm 424 NUT M10 12 65 WASHER PRESS RING 225 STEEL BALL PIN - XLT ONLY 4 66 IRON TYRE 226 STABILIZATION PIPE CAP - XLT ONLY 2 67 DOLLY STE 127 STABILZATION BAR - XLT ONLY 1 68 BOLT 228 LIFTING ARM 1 69 DOLLY HANDLE 129 INNER HEXAGON SCREW 2 70 FLAT HEAD MACHINE SCREW 2430 COTTER 4 71 NUT 231 BEARING 4 72 PRESS RING 232 PRESS RING 2 73 RUBBER VISE PAD - RIGHT 133 WHEEL 2 74 RUBBER VISE PAD - LEFT 134 LIFTING ARM 1 75 PLASTIC VISE END CAP - BLK 435 RETAINGING RING 2 76 PLASTIC WHEEL STOP END CAP - BLK 236 BEARING 4 77 VISE HANDLE - PLASTIC 137 PRESS RING 2 78 ROLLER DROP OUT (SEE FIG. 3) 138 CONNECTION 1 79 LONG RAMP 139 BOLT M10*45 2 80 LEFT EXTENSION RAMP 140 ROLLER 2 81 BOLT (VISE ATTACHMENT) 441 WASHER Φ16 4 82 RETAINING RING 442 LOCK NUT M16 2

88 9

FOOT VALVE PARTS DETAIL (FIG. 2)

NO. DESCRIPTION QTY NO DESCRIPTION QTY

1 FOOT PEDAL 1 7 SNAP RING 12 RETAINING RING 1 8 LOCK NUT 13 WASHER 2 9 BASE 14 PLUNGER VALVE 1 10 HEXAGON BOLT 15 O-RING 3 11 AIR FITTING 16 NYLON BUSHING 1

10

ROLLER DROP-OUT PARTS DETAIL (FIG. 3)

NO. DESCRIPTION QTY1 DROPOUT PLATE 12 RETAINING NUT M8 43 BEARING 44 ROLLER 25 PIN 26 BUSHING 4

10

®

PO Box 7069 Greenwood, IN 461421.888.908-4826 FAX (317) 215.2770

www.titanlifts.com

TITAN MARKETING, LLC

Revision 6

Copyright © 2010 by Titan Marketing, LLC. All rights reserved. No portion of this manual or any artwork contained herein may be reproduced in any shape or form without the express consent of Titan Marketing, LLC. Diagrams within this manual may not be drawn proportionally. Due to continuing improvements, actual product may differ slightly from the product described herein. Tools required for assembly and service may not be included.