tmhsiung@2014 1/30 chapter 25 instruments for optical spectrometry
TRANSCRIPT
TMHsiung@2014 1/30
Chapter 25 Instruments for Optical
Spectrometry
Contents in Chapter 25
1. Instrument Components2. Basic Components of Spectroscopic
Instrumentation1) Sources of Energy2) Wavelength Selector3) Sample Holder4) Detectors5) Signal Processors
3. UV/visible Photometers and Spectrophotometers
TMHsiung@2014 2/30
1. Instrument Components
1) Most spectroscopic instruments in the UV/visible and IR regions are made up of five components:(1) Sources of Energy(2) Wavelength Selector(3) Sample Holder(4) Detectors(5) Signal Processors
TMHsiung@2014 3/30
Filter 濾光鏡Interference filter 干涉濾鏡Absorption filter 吸收濾鏡
Monochromator 單光儀 Grating 光柵 Prism 稜鏡Slit 狹縫 Bandwidth 頻寬
Interferometer 干涉計Fourier Transform (FT) 傅立葉轉換Time domain 時域 Frequency domain 頻域
Glossary
TMHsiung@2014 4/30
2) Conceptual Block Diagram of Spectrometer
LightSource
Wavelengthselector
Sample Detector Signal processor and readout
(1) For absorption measurement
Wavelengthselector
Sample Detector Signal processor and readout
(2) For emission measurement
Thermal
*****
TMHsiung@2014 5/30
LightSource
Wavelengthselector
Sample
Detector Signal processor and readout
(3) For fluorescence measurement
Wavelengthselector
Sample +Reagent
DetectorSignal processor
and readout
(4) For chemiluminescence measurement
Wavelengthselector
TMHsiung@2014 6/30
2. Basic Components of Spectroscopic Instrumentation
1) Sources of Energy
• For absorption and scattering spectroscopy: Energy is supplied by photons (electromagnetic radiation).
• For emission and luminescence spectroscopy: Thermal, radiant (photon), or chemical energy to promote the analyte higher energy state.
(1) Light (Electromagnetic Radiation) Sources:
– Continuum source: A source emits radiation over a wide range
of wavelengths.
– Line sources: A source emit radiation at selected wavelength
ranges.
TMHsiung@2014 7/30
Electrodeless discharge lamp line source in UV/Vis atomic absorption
(cont’d)
TMHsiung@2014 8/30
(cont’d)
(2) Thermal Energy (for emission spectrometer): e.g., flames and
plasmas. Flame: (fuel/oxidant, e.g., acetylene/air), achieve
temperatures of 2000–3400 K. Plasmas: (ionized gases, e.g.,
Ar), temperatures of 6000–10,000 K.
(3) Chemical Sources of Energy: e.g., in chemiluminescence, the
analyte is raised to a higher-energy state by means of a chemical
reaction, emitting characteristic radiation when it returns to a
lower-energy state.
TMHsiung@2014 9/30
Effective bandwidth
• For qualitative purpose, narrow slit increase the spectra resolution.
• For quantitative purpose, wilder slit provide greater reproducibility.
• Effective bandwidth: The bandwidth of a monochromator or and interference filter at which the transmittance is 50% of that at nominal wavelength.
• Narrow slit decrease s the effective bandwidth, also diminishes the throughput of radiation.
2) Wavelength Selector
TMHsiung@2014 10/30
(1) Filter: A wavelength selector that uses either absorption, or constructive and destructive interference to control the range of selected wavelengths.a) Interference filterb) Absorption filter
Type Interference filter Absorption filter
Theory use constructive and destructive interference to isolate a narrow range of wavelengths.
Colored glass or a dye suspended in gelatin, which removes the complementary color
Effective
bandwidths
10–20 nm 30–250 nm.
Maximum throughputs
> 40%. 10%
(cont’d)
TMHsiung@2014 11/30
Interference Filters
• Consists of a transparent dielectric that occupies the space between two semitransparent metallic films. All of this is sandwiched between glass or other transparent materials.
• If the distance traveled by the reflected beam from 1 is some multiple of the wavelength, then reinforcement will occur at point 2.
• The nominal wavelength for an
interference filter λmax is given by the
equation:
max = 2t/nt is the thickness of the central fluoride η is its refractive index n is an integer called the interference order.
TMHsiung@2014 12/30
(2) Monochromator: A wavelength selector that uses a diffraction grating or prism, and that allows for a continuous variation of the nominal wavelength.a) Diffraction gratingb) Prism
TMHsiung@2014 13/30
Components of a Monochromator
Collimatingmirror
Focusingmirror
A polychromatic radiation is converted to a monochromatic radiation of finite effective bandwidth.A scanning monochromator includes a drive mechanism, allowing successive wavelengths to exit from the monochromator.
prism
grating
TMHsiung@2014 14/30
Dispersion of radiation
TMHsiung@2014 15/30
Reflection Grating A reflective surface is grooved or blazed giving numerous faces
for reflection to occur, beam 2 travels a longer distance than beam 1. If the extra distance traveled is a multiple of the wavelength, then constructive interference will occur.
• The angle of reflection
r is related to the
wavelength of the
incoming radiation by
the equation
n = d(sin i + sin r)
TMHsiung@2014 16/30
TMHsiung@2014 17/30
(3) Polychromator: A wavelength selector in which different directions of the dispersed light (by prism or diffraction grating), simultaneously detected by a multi-detector (e.g., photodiode array, PDA)
TMHsiung@2014 18/30
(cont’d)
Photodiode array (PDA): A linear array of photodiodes providing the ability to detect simultaneously radiation at several wavelengths.
Polychromator
TMHsiung@2014 19/30
(4) Interferometer• Interferometer: A device that allows all wavelengths of light
to be measured simultaneously.• The signal shows a function of the moving mirror’s position.
The result is called an interferogram, or a time domain spectrum.
• The time domain spectrum is converted by Fourier Transform, to the normal spectrum (also called a frequency domain spectrum).
• Fourier transform IR spectrometers have the advantages over dispersive instruments of higher speed and sensitivity, better light-gathering power, more accurate and precise wavelength settings, simpler mechanical design, and elimination of stray light and IR emission.
TMHsiung@2014 20/30
3) Sample Holder/Matrix
(1) Feasibility of cuvette materials
Sample containers, which are usually called cells or cuvettes, must have windows that are transparent in the spectral region of interest.
TMHsiung@2014 21/30
(2) Feasibility of preparation solvent
TMHsiung@2014 22/30
4) Detectors
• Modern detectors use a sensitive transducer to convert a signal
consisting of photons into an easily measured electrical signal.• Ideally the detector’s signal (S):
S = kP + D P: electromagnetic radiation’s power
k: detector’s sensitivity
D is the detector’s dark current
Dark current: The background current present in a photon detector in the absence of radiation from the source.
TMHsiung@2014 23/30
Characteristics of transducers for optical spectroscopy
• Charge-injection device (CID) detector: The voltage change arising from movement of the charge from the region under one electrode to the region under the other is measured.
• Charge-coupled device (CCD) detector: The charge is moved to a charge-sensing amplifier for measurement.
TMHsiung@2014 24/30
5) Signal Processor
Signal processor A device, such as a meter or computer, that
displays the signal from the transducer in a form that is easily
interpreted by the analyst.
• Examples: analog meters, digital meters, recorders, and
computers.
• Additionally, signal processor may be used to calibrate the
detector’s response, to amplify the signal from the detector, to
remove noise by filtering, or to mathematically transform the
signal.
TMHsiung@2014 25/30
3. UV/visible Photometers and Spectrophotometers1) Classification
(1) Spectrometer: A spectroscopic instrument that uses a monochromator or polychromator in conjunction with a transducer to convert the radiant intensities into electrical signals.
(2) Spectrophotometer: The spectrometer that allows measurement of the ratio of the radiant powers of two beams, a requirement to measure absorbance.
(3) Photometer: A spectroscopic instrument that uses a filter for wavelength selection in conjunction with a suitable radiation transducer.
TMHsiung@2014 26/30
2) Single beam versus Double beam
(1) Single beam instrument
(2) Double beam instrument
TMHsiung@2014 27/30
3) Instrumentation for Fluorescence (1) Fluorometer: an
instrument for measuring fluorescence that uses filters to select the excitation and emission wavelengths.
(2) Spectrofluorometer: an instrument for measuring fluorescence that uses a monochromator to select the excitation and emission wavelengths.
TMHsiung@2014 28/30
Practice
Q3. Which of followings are used for wavelength selection:
(A) Filter (B) Monochromator
(C) Interferometer (D) Tungsten lamp
A2. (A)
A3. (A)(B)(C)
Q1. The reciprocal of wavelength is called:
(A) Amplitude (B) Wavenumber
(C) Frequency (D) Period
A1. (B)
Q2. Photomultiplier is a:
(A) Photon transducers (B) Thermal transducers
(C) Absorption filter (D) Interferometer
TMHsiung@2014 29/30
Homework
Skoog 9th edition, Chapter 25 Questions and Problems25-625-1325-1825-19
End of Chapter 25
TMHsiung@2014 30/30