tooling - afshuck.net®//huckspin tool (hk993).pdf · tooling, other items, nonstandard or custom...
TRANSCRIPT
05-18-2004 Form HK993
Instruction Manual
HuckSpinTOOLINGHydraulic Installation Tool
Huckspin Tooling Alcoa Fastening Systems
SAFETYThis instruction manual must be read with particularattention to the following safety guide lines, by anyperson servicing or operating this tool.
1. Safety Glossary
WARNINGS - Must be understood to avoid severe personal injury.
CAUTIONS - show conditions that willdamage equipment and or structure.Notes - are reminders of requiredprocedures.Bold, Italic type and underlining -emphasizes a specific instruction.
2. Huck equipment must be maintained in a safeworking condition at all times and inspected on aregular basis for damage or wear. Any repairshould be done by a qualified repairman trainedon Huck procedures.
3. Repairman and Operator must read manual priorto using equipment and understand any Warningand Caution stickers/labels supplied withequipment before connecting equipment to anyprimary power supply. As applicable, each of thesections in this manual have specific safety andother information.
4. See MSDS Specifications before servicing thetool. MSDS Specifications are available fromyou Huck representative or on-line atwww.huck.com. Click on Installation SystemsDivision.
5. When repairing or operating Huck installationequipment, always wear approved eyeprotection. Where applicable, refer to ANSIZ87.1 - 1989
6. Disconnect primary power source before doingmaintenance on Huck equipment.
7. If any equipment shows signs of damage, wear,or leakage, do not connect it to the primarypower supply.
8. Make sure proper power source is used at alltimes.
9. Never remove any safety guards or pintaildeflector.
10. Never install a fastener in free air. Personalinjury from fastener ejecting may occur.
11. When using an offset nose always clear spentpintail out of nose assembly before installing thenext fastener.
12. If there is a pinch point between trigger andwork piece use remote trigger. (Remotetriggers are available for all tooling).
13. Do not abuse tool by dropping or using it as ahammer. Never use hydraulic or air lines as ahandle. Reasonable care of installation tools byoperators is an important factor in maintainingtool efficiency, eliminating downtime, and inpreventing an accident which may cause severepersonal injury.
14. Never place hands between nose assembly andwork piece.
15. Tools with ejector rods should never be cycledwith out nose assembly installed.
16. When two piece lock bolts are being usedalways make sure the collar orientation iscorrect. See fastener data sheet of correctpositioning.
�
Product complies with requirementsset forth by the relevant Europeandirectives.
Read manual prior to usingequipment.
Eye protection required whileusing this equipment.
Hearing protection required whileusing this equipment.
Huckspin Tooling Alcoa Fastening Systems
SERVICE NOTES:
Huckspin Tooling Alcoa Fastening Systems
LIMITED WARRANTIESTooling Warranty: Huck warrants that tooling and otheritems (excluding fasteners, and hereinafter referred as"other items") manufactured by Huck shall be free fromdefects in workmanship and materials for a period ofninety (90) days from the date of original purchase.
Warranty on "non standard or custom manufacturedproducts": With regard to non-standard products orcustom manufactured products to customer'sspecifications, Huck warrants for a period of ninety (90)days from the date of purchase that such products shallmeet Buyer's specifications, be free of defects inworkmanship and materials. Such warranty shall not beeffective with respect to non-standard or custom productsmanufactured using buyer-supplied molds, material,tooling and fixtures that are not in good condition or repairand suitable for their intended purpose.
THERE ARE NO WARRANTIES WHICH EXTENDBEYOND THE DESCRIPTION ON THE FACE HEREOF.HUCK MAKES NO OTHER WARRANTIES ANDEXPRESSLY DISCLAIMS ANY OTHER WARRANTIES,INCLUDING IMPLIED WARRANTIES AS TOMERCHANTABILITY OR AS TO THE FITNESS OF THETOOLING, OTHER ITEMS, NONSTANDARD ORCUSTOM MANUFACTURED PRODUCTS FOR ANYPARTICULAR PURPOSE AND HUCK SHALL NOT BELIABLE FOR ANY LOSS OR DAMAGE, DIRECTLY ORINDIRECTLY, ARISING FROM THE USE OF SUCHTOOLING, OTHER ITEMS, NONSTANDARD ORCUSTOM MANUFACTURED PRODUCTS OR BREACHOF WARRANTY OR FOR ANY CLAIM FORINCIDENTAL OR CONSEQUENTIAL DAMAGES.
Huck's sole liability and Buyer's exclusive remedy for anybreach of warranty shall be limited, at Huck's option, toreplacement or repair, at FOB Huck's plant, of Huckmanufactured tooling, other items, nonstandard or customproducts found to be defective in specifications,workmanship and materials not otherwise the direct orindirect cause of Buyer supplied molds, material, toolingor fixtures. Buyer shall give Huck written notice of claimsfor defects within the ninety (90) day warranty period fortooling, other items, nonstandard or custom productsdescribed above and Huck shall inspect products for whichsuch claim is made.
Tooling, Part(s) and Other Items not manufactured byHuck.
HUCK MAKES NO WARRANTY WITH RESPECT TOTHE TOOLING, PART(S) OR OTHER ITEMSMANUFACTURED BY THIRD PARTIES. HUCKEXPRESSLY DISCLAIMS ANY WARRANTYEXPRESSED OR IMPLIED, AS TO THE CONDITION,
DESIGN, OPERATION, MERCHANTABILITY ORFITNESS FOR USE OF ANY TOOL, PART(S), OROTHER ITEMS THEREOF NOT MANUFACTURED BYHUCK. HUCK SHALL NOT BE LIABLE FOR ANY LOSSOR DAMAGE, DIRECTLY OR INDIRECTLY, ARISINGFROM THE USE OF SUCH TOOLING, PART(S) OROTHER ITEMS OR BREACH OF WARRANTY OR FORANY CLAIM FOR INCIDENTAL OR CONSEQUENTIALDAMAGES.
The only warranties made with respect to such tool, part(s)or other items thereof are those made by the manufacturerthereof and Huck agrees to cooperate with Buyer inenforcing such warranties when such action is necessary.
Huck shall not be liable for any loss or damage resultingfrom delays or nonfulfillment of orders owing to strikes,fires, accidents, transportation companies or for anyreason or reasons beyond the control of the Huck or itssuppliers.
Huck Installation Equipment
Huck International, Inc. reserves the right to makechanges in specifications and design and to discontinuemodels without notice.
Huck Installation Equipment should be serviced by trainedservice technicians only.
Always give the Serial Number of the equipment whencorresponding or ordering service parts.
Complete repair facilities are maintained by HuckInternational, Inc. Please contact one of the offices listedbelow.
EasternOne Corporate Drive Kingston, New York 12401-0250Telephone (845) 331-7300 FAX (845) 334-7333
Canada6150 Kennedy Road Unit 10, Mississauga, Ontario,L5T2J4, Canada.Telephone (905) 564-4825 FAX (905) 564-1963
Outside USA and CanadaContact your nearest Huck International Office, see backcover.
In addition to the above repair facilities, there areAuthorized Tool Service Centers (ATSC's) locatedthroughout the United States. These service centers offerrepair services, spare parts, Service Parts Kits, ServiceTools Kits and Nose Assemblies. Please contact yourHuck Representative or the nearest Huck office listed onthe back cover for the ATSC in your area.
Americas
Alcoa Fastening SystemsAerospace ProductsTucson Operations3724 East ColumbiaTucson, AZ 85714800-234-4825520-747-9898FAX: 520-748-2142
Alcoa Fastening SystemsAerospace ProductsCarson OperationsPO Box 5268900 Watson Center Rd.Carson, CA 90749800-421-1459310-830-8200FAX: 310-830-1436
Alcoa Fastening SystemsCommercial ProductsWaco OperationsPO Box 81178001 Imperial DriveWaco, TX 76714-8117800-388-4825254-776-2000FAX: 254-751-5259
Alcoa Fastening SystemsCommercial ProductsKingston Operations1 Corporate DriveKingston, NY 12401800-431-3091845-331-7300FAX: 845-334-7333www.hucktools.com
Alcoa Fastening SystemsCommercial ProductsCanada Operations6150 Kennedy Road, Unit 10Mississagua, Ontario L5T2J4Canada905-564-4825FAX: 905-564-1963
Alcoa Fastening SystemsCommercial ProductsLatin America OperationsAvenida Parque Lira. 79-402Tacubaya Mexico, D.F.C.P. 11850FAX: 525-515-1776TELEX: 1173530 LUKSME
Far East
Alcoa Fastening SystemsCommercial ProductsAustralia Operations14 Viewtech PlaceRowville, Victoria Australia 317803-764-5500Toll Free: 008-335-030FAX: 03-764-5510
Europe
Alcoa Fastening SystemsCommercial ProductsUnited Kingdom OperationsUnit C, Stafford Park 7Telford, ShropshireEngland TF3 3BQ01952-290011FAX: 0952-290459
Alcoa Fastening SystemsAerospace ProductsFrance OperationsClos D’AssevilleBP495450 Us Par VignyFrance33-1-30-27-9500FAX: 33-1-34-66-0600
For the Long Haul™
A Global OrganizationAlcoa Fastening Systems (AFS) maintains companyoffices throughout the United States and Canada,with subsidiary offices in many other countries.Authorized AFS distributors are also located inmany of the world’s
industrial and Aerspace centers, where they providea ready source of AFS fasteners, installation tools,tool parts, and application assistance.
For The Long Haul, The Future of Fastening Technology,The Future of Assembly Technology, The Future of ToolingTechnology, and Tools of Productivity are service marks of HuckInternational. Huck provides technical assistance regarding the useand application of Huck fasteners and tooling.
NOTICE: The information contained in this publication is only forgeneral guidance with regard to properties of the products shown
and/or the means for selecting such products, and is not intendedto create any warranty, express, implied, or statutory; all warrantiesare contained only in Huck’s written quotations,acknowledgements, and/or purchase orders. It is recommendedthat the user secure specific, up-to-date data and informationregarding each application and/or use of such products.
HWB898 1003-5M
© 2003 Alcoa Fastening Systems
1 Corporate Drive, Kingston, NY 12401 • Tel: 800-431-3091 • Fax: 845-334-7333 • E-mail: [email protected] • www.alcoafasteningsystems.com
Alcoa Fastening Systems world-wide locations:
One Great ConnectionSM