tools required...king pin axle × 2 × 2 cross pin × 4 5 × 8 × 0.25 shims × 2 serrated locknut...

This assembly manual contains instructions for building your new PRO-MT. Please take your time building the kit according to the instructions and become familiar with the steps.

Pro-Line is continually improving our products; consequently, actual parts included in the PRO-MT kit may appear slightly different than the images that appear in this manual.

WARNING! This is NOT a toy and is NOT suitable for children under 14 years of age. This kit contains many small parts which are potential choking hazards. Keep all components out of reach of small children.

HEALTH WARNING! This product contains chemicals known to the State of California to cause cancer, birth defects, or other reproductive harm. This kit is a high performance radio controlled model kit and can cause harm or personal injury. All liquids contained in this kit are not to be swallowed. Never touch rotating parts as this can cause injury.

TOOLS REQUIRED

1.5mm HEX 2.0mm HEX 2.5mm HEX 5mm NUT DRIVER 5.5mm NUT DRIVER 7mm NUT DRIVER BODY REAMER SIDE-CUT PLIERS BODY SCISSORS

EQUIPMENT REQUIRED

RADIO RECEIVER ESC MOTOR PINION GEAR SERVO & HORN

+-

BATTERY

+-

CHARGER PAINT

Thank you for purchasing Pro-Line’s PRO-MT! For over 30 years, Pro-Line has designed and manufactured the best RC accessories in the world. Pro-Line has taken

the best performance parts and combined them into one complete kit. Congratulations on making the right decision and joining Team Pro-Line in making history!

INCLUDED PERfORMANCE PARTS

Enjoy your Ride!From your friends at Pro-Line

• Pro-Line Performance HD Transmission• PRO-MT Aluminum Chassis• PowerStroke Shocks• ProTrac Suspension Kit• Performance Steering Kit• PRO-MT Sentinel Body

• Secure-Loc Body Mount System• Trencher 2.8" All-Terrain Pre-Mounted Tires • F-11 2.8" ProTrac Offset Black Wheels• Military-grade Components• Pro-Spline Axles

HELP AND INfORMATIONInstallation manuals and videos can be found on our website at prolineracing.com/pro-mt/build For any help you may need, you can call our tech support line at 1-800-899-RACE(7223).

REGISTRATIONRegister your PRO-MT kit online at prolineracing.com/pro-mt/register or call 1-800-899-RACE(7223).

SCAN fOR HELP SCAN TO REGISTER

HARDWARE USED(ACTUAL SIZE)



× 2 M3 × 16 BHCS

× 4

M4 × 12 FHCS

1 BA

G A

BA

G A

BA

G A

2

3

× 2 M3 × 8 SHCS

× 2 M3 × 12 SHCS

Front Bumper Assembly

Front Shock Tower to Bulkhead

Front Bumper to Bulkhead

M3 × 12

M3 × 8




4 BA

G B

BA

G C

BA

G C

5

6

× 2 M3 X 30 SHCS

× 2 M3 Washer

× 2 Ball Ends

× 2 M3 Locknut

× 2 M3 × 12 Low Profile

× 2 M3 × 14 BHCS

× 2 Black O-Ring

× 2 M4 × 14 Setscrew

× 2

Secure-Loc Cap

Front Shock Mounting Hardware

Front Body Mount to Shock Tower

Front Body Mount Hardware

MIDDLE HOLE

7TH HOLE fROM TOP

OUTSIDE HOLES

Install setscrew leaving½ of the threads exposed




7 BA

G d

BA

G d

BA

G d

8

9

× 4 Long Rod Ends

× 2 Small Inner Pivot Balls

× 2 Large Inner Pivot Balls


Front Camber Link Rod Ends

Front Camber Link Pivot Balls

Front Camber Links to Shock Tower

USE INCLUDED TURNBUCKLE WRENCH

50mm (ACTUAL SIZE)

27.5mm (ACTUAL SIZE)

× 2

“DRIVER’S SIDE” AND “PASSENGER’S SIDE” REfER TO U.S. STANDARDS

DRIVER’S SIDE LINK

PASSENGER’S SIDE LINK

KEEP THESE MARKS ON DRIVER’S SIDE


MIDDLE HOLE




10

BA

G d

BA

G E

BA

G E

11

12

× 4 5 × 11 Bearing

× 2 King Pin

Axle × 2

× 2 Cross Pin

× 4 5 × 8 × 0.25 Shims

× 2 Serrated Locknut

× 2 M1.6 × 6 SHCS

REPEAT THIS STEP fOR OPPOSITE SIDE


Front Arms & Hinge Pin Brace to Bulkhead

Front Hub Assembly

Front Wheel Hex Assembly

× 2

Front Inner Hinge Pin

× 2 M3 Locknut

Hinge Pin Brace × 1

2 x SHIMS BETWEEN BEARING AND PIN1

2

3




13 BA

G F

BA

G F

BA

G F

14

15

× 2 Front Outer Hinge Pin

× 2 M2.5 Locknut

× 2 M3 × 18 BHCS

× 2 M3 Locknut

× 4 Short Rod Ends

× 4 Large Pivot Balls

× 2 M3 × 18 BHCS

× 2 M3 Locknut



Front Hub Assembly to Camber Link & Arm

Steering Links to Rod Ends & Pivot Balls

Steering Link to Steering Knuckle

OUTSIDE HOLE

M2.5 LOCKNUT

M3 LOCKNUT

USE INCLUDED TURNBUCKLE WRENCH, REPEAT THIS STEP fOR OPPOSITE SIDE

70mm (ACTUAL SIZE)

53.5mm (ACTUAL SIZE)

× 2





16 BA

G F

BA

G G

BA

G G

17

18

× 2 M3 Locknut

× 3 M4 × 10 FHCS

× 2 M4 × 14 BHCS

Steering Links to Steering Kit

Assemble Front End to Chassis

Front Bumper Brace to Front Bulkhead





MIDDLE HOLES

19

BA

G G

BA

G G

BA

G G

20

21

× 2 M3 × 25 SHCS

× 2 M3 Washer

× 2 Ball Ends

× 2 M3 Locknut

× 4 Long Rod Ends

× 2 Small Inner Pivot Balls

× 2 Large Inner Pivot Balls


Rear Shock Mounting Hardware

Rear Camber Links to Rod Ends & Pivot Balls

Rear Camber Links to Shock Tower

INNER HOLES

*Use caution if using power tools. Heat may melt plastic.

50mm (ACTUAL SIZE)

29.5mm(ACTUAL SIZE)

× 2

DRIVER’S SIDE LINK

PASSENGER’S SIDE LINK


USE INCLUDED TURNBUCKLE WRENCH




22

PR

Ot

RA

C B

AG

BA

G H

BA

G H

23

24

× 4 M3 × 16 BHCS

× 2 M3 × 14 BHCS

× 4 M2.5 × 12 SHCS

× 2 Black O-Ring


× 2

Secure-Loc Cap

Rear Shock Tower to Transmission Case

Rear Body Mount to Shock Tower

Rear Body Mount Hardware

TOP HOLES

Install setscrew leaving½ of the threads exposed




25 BA

G I

BA

G I

BA

G J

26

27

× 2 drive Pin

× 2 drive Pin Cup

× 2 M3 Set Screw

× 2 Retainer Clip

Female driveshaft × 2

Sliding Outsdrive × 2


× 2 drive Pin

× 2 drive Pin Cup

× 2 M3 Set Screw

Male driveshaft × 2

Axle × 2

REMOVE GEAR COVER fOR OPPOSITE SIDE INSTALLATION


REPEAT THIS STEP fOR OPPOSITE SIDE.

Outdrive Assembly

Outdrives to Transmission

Driveshaft & Axle Assembly

1

2

3

4 5

1

4

3

2

PRO TIPRotate retainer clip so slit is away from pin holes and add a drop of CA Tire Glue (not included) in slit to prevent rotation of clip.




BA

G J

B

AG

JB

AG

K

29

30




Driveshaft to Outdrive & Hub Carrier

Rear Wheel Hex Assembly

Rear Arm & Camber Link Assembly

× 2 18 × 12 × 4 Bearings

× 2 5 × 11 Bearing

28

× 2 Cross Pin

× 4 5 × 8 × 0.25 Shims

× 2 Serrated Locknut

× 2 M1.6 × 6 SHCS

2 x SHIMS BETWEEN BEARING AND PIN

MIDDLE HOLE

1

2

3

× 2 Rear Outer Hinge Pin

× 2

Rear Inner Hinge Pin

× 2 M3 × 20 BHCS

× 6 M3 Locknut




BA

G K

BA

G K

32

33

× 2 M3 × 16 BHCS

Use M3 Locknuts installed on Step 4

× 2 M3 × 16 BHCS

Use M3 Locknuts installed on Step 19

Install Front Shocks

Install Rear Shocks

31 Shock Setup (Fluids Bag)

1. Remove Springs2. fill with oil3. Bleed4. Tighten5. Replace Springs

Visit prolineracing.com/pro-mt/build

for shock assembly videos and spring rate charts.

HOLE 2fROM INSIDE

OUTSIDE HOLE

× 4

PRO TIPMove bottom shock mounting position inward for more suspension travel.


BA

G L

Servo Link

17mm (ACTUAL SIZE)Steering Rod

× 2 Short Rod Ends

× 2 Large Pivot Balls



BA

G L

36Install Servo

× 2 M3 × 16 BHCS

× 2 3 × 7 × 2.5 Spacers

1. Remove (4) screws in servo mount 2. Loosen (4) screws in top brace3. Install servo4. Tighten all screws5. Zero out servo with horn vertical6. Align link straight with spacers7. Reinstall side pod from Step 35

Remove Passenger Side Pod

35

34

PRO TIPUse thread-locking compound on all screws threading into metal.

1

2

2

2

2

3

5

61

1

1




BA

G L

37FO

AM

BA

Gt

IRE

BA

G

38

39

Motor Installation

Electronics Placement

Install Pre-mounted Trencher Tires

× 2 M3 × 8 SHCS

× 2 Hd Motor Washer

1. Remove HD Transmisison Cover2. Install Motor 3. Set Gear Mesh (Pinion sold separately)4. Reinstall Gear Cover

SPEED CONTROLLER (Not Included)

fOAM STRIPSANTENNA TUBE

RECEIVER (Not Included)




40B

Od

y B

AG

41

Congratulations! Enjoy your Pro-Line PRO-MT!

Paint & Mount Sentinel Body

PRO TIPS1. Paint body with Lexan/

polycarbonate safe paint2. Allow paint to dry completely3. Remove window masks and

outer film4. Apply decals5. Ream body post holes on

marked dimples6. Mount body to chassis using

Secure-Loc Caps

Trim & Prep Sentinel Body

PRO TIPS1. Cut body along trimlines2. Wash Body with soap3. Rinse and dry thoroughly4. Install window masks

6261-00 HD Performance Transmission

6092-01 Transmission Plastics

6092-02 Gear Cover & Plug

6092-03 Motor Plate

6092-04 Transmission Hardware

6092-05 Diff Housing & Idler Gear

6092-06 Diff Internal Gears

6092-07 86T Spur Gear (Stock)

6092-08 Diff Seal Kit

6092-09 Top Shaft & Slipper Plates

6092-10 Slipper Pads

6092-11 Ball Bearings

6063-00 Power Stroke Shocks (front)

6063-02 Shock Rebuild Kit (2)

6063-03 Front Spring Assortment Kit

6063-05 Mounting Hardware (4)

6063-06 Front Shaft Replacement (2)

6063-01 Power Stroke Shocks (Rear)

6063-02 Shock Rebuild Kit (2)

6063-04 Rear Spring Assortment Kit

6063-05 Mounting Hardware (4)

6063-07 Rear Shaft Replacement (2)

6102-00 Pivot Ball & Rod End Set

6104-00 Front Hinge Pin Brace

6096-00 PRO-2 Hinge Pin Set

6097-00 PRO-2 Front Clamping Hex (2)

6098-00 PRO-2 Rear Clamping Hex (2)

6100-00 4mm Serrated Wheel Nuts (4)

1170-14 Trencher 2.8” on F-11 Wheels (2)

3435-00 Sentinel Clear Body

6262-00 PRO-MT Chassis

Replacement Parts

6262-12 Aluminum Chassis

6262-01 Side Pod Plastics

6262-02 Internal Plastics

6093-04 Servo Mounts & Hardware

6093-05 Steering Posts & Hardware

6062-00 ProTrac Suspension Kit

6062-01 Front Arms

6062-02 Rear Arms

6062-03 Front Shock Tower

6062-04 Rear Shock Tower

6062-06 Camber Links (2)

6062-07 Steering Links (2)

6067-00 Performance Steering Kit

6070-00 Extended Body Mount Kit

6070-01 Body Mount Plastics

6070-02 Thumbwashers & Hardware

6101-00 PRO-2 front Hub Kit

6101-01 Front Hub Plastics

6101-02 Steel King Pins (4)

6255-00 Aluminum Caster Blocks

6092-16 HD Motor Washers

6262-03 PRO-MT Front Bumper &

Bulkhead

6262-04 PRO-MT Rear Bumper

6262-05 PRO-MT Rear Hub Carriers

6262-06 PRO-MT HD Sliding Axle Kit

6262-07 Drive Pins & Clips

6262-08 Replacement Outdrive

6262-09 Replacement Female Drive Shaft

6262-10 Replacement Male Drive Shaft

6262-11 Replacement Rear Axle

OPTIONAL PARTS

6092-12 Optional Anti-Squat Blocks

6092-13 Optional 78T Spur Gear

6092-15 Optional 82T Spur Gear

6063-03 Front Spring Assortment Kit

6063-04 Rear Spring Assortment Kit

6067-01 Aluminum Steering Rack

6092-00 MIP Super Ball Diff Kit

6308-30 Pre-Assembled Pro-Spec

Shocks (Front)

6308-31 Pre-Assembled Pro-Spec

Shocks (Rear)

6109-00 Carbon Fiber Shock Tower

Brace (Front)

6109-00 Carbon Fiber Shock Tower

Brace (Rear)

Check out our website for our full line of MT Tires, Wheels, Bodies and Accessories!

TRACK:EVENT:

DRIVER:QUAL:

Stock PRO-MT Setup

DATE:FINISH:

FRONT PROTRAC SUSPENSION

REAR PROTRAC SUSPENSION

ELECTRONICS

TRACK INFORMATION

FRONT TIRES REAR TIRES

MOTOR:ESC:

RECEIVER:SERVO:RADIO:

PINION:SPUR GEAR:

DIFF. OIL:Stock 86 toothStock 5,000 wt.

TIRE:COMPOUND:

INSERT:WHEEL:

Trencher 2.8”M2StockF-11 2.8” (#2743-03)

Trencher 2.8”M2StockF-11 2.8” (#2743-03)

TRACTION:SURFACE:

CONDITIONS:

HIGH MED LOW SMOOTH BUMPY BLUE GROOVE SOFT DIRT CLAY WET DUSTYOTHER:

1 2 3

CAMBER:TOE:

RIDE HEIGHT:

2235

°°mm

1 2

TIRE:COMPOUND:

INSERT:WHEEL:

For complete step-by-step instructions visit PROLINERACING.com

INSIDE

INSIDE

CAMBER:ANTI-SQUAT:RIDE HEIGHT:

°°mm

FRONT SHOCKS

REAR SHOCKS

(A) PISTON:OIL WEIGHT:

(B) PRIMARY SPRING:(C) SECONDARY SPRING:

DROOP SPACER:COMPRESSION SPACER:

(D) SPRING ADJUSTMENT:

Stock45 wtYellowGreen





Stock45 wtYellowGreen

D

TRANSMISSION SETTINGS

NOTES

A

B

C

D

A

B

C

2335

MONSTER TRUCK SETUP SHEET

TRACK:EVENT:

DRIVER:QUAL:

DATE:FINISH:

FRONT PROTRAC SUSPENSION

REAR PROTRAC SUSPENSION

ELECTRONICS

TRACK INFORMATION

FRONT TIRES REAR TIRES

MOTOR:ESC:

RECEIVER:SERVO:RADIO:

PINION:SPUR GEAR:

DIFF. OIL:

TIRE:COMPOUND:

INSERT:WHEEL:

TRACTION:SURFACE:

CONDITIONS:

HIGH MED LOW SMOOTH BUMPY BLUE GROOVE SOFT DIRT CLAY WET DUSTYOTHER:

1 2 3

CAMBER:TOE:

RIDE HEIGHT:

°°mm

1 2

TIRE:COMPOUND:

INSERT:WHEEL:

For complete step-by-step instructions visit PROLINERACING.com

INSIDE

INSIDE

CAMBER:ANTI-SQUAT:RIDE HEIGHT:

°°mm

FRONT SHOCKS

REAR SHOCKS









D

TRANSMISSION SETTINGS

NOTES

A

B

C

D

A

B

C

MONSTER TRUCK SETUP SHEET

tools required...king pin axle × 2 × 2 cross pin × 4 5 × 8 × 0.25 shims × 2 serrated locknut...

Documents