trapper bass distortion · 2020. 8. 6. · dc power connector 3 12 leds 9v dc input trapper bass...
TRANSCRIPT
TRAPPER BASS DISTORTION
13
14
1
2
11
8
4 5 6
1. Distortion 2 Footswitch/LED2. Output Jack3. Sub Level (Distortion2)4. Frequency (Distortion 2)5. Level (Distortion2)6. Tone (Distortion2)7. Gain (Distortion2)
8. Gain (Distortion1)9. Tone (Distortion1)10. Level (Distortion1)11. Input Jack12. Distortion 1 Footswitch/LED13. LED Kill Switch14. DC Power Connector
3
12
LEDs
9V DCINPUT
TRAPPER BASS DISTORTION
GAIN 1SUB LVL 2 LEVEL 1 TONE 1
GAIN 2
DIST 1DIST 2
9
7
LEVEL 2 TONE 2FREQ 2
10
Add crunch to your low end with the Trapper Bass Distortion. Featuring two separate and stackable distortion circuits, this pedal specifically fits the tonal needs of electric bass players. The main distortion channel features a crossover-blend circuit to preserve clean low-frequency information for clarity and punch, while an additional “solo” distortion channel provides added gain and crunch. Use the Frequency and Sub Level controls to dial in the fundamental tone.
Designed by our in-house team of experts, the Trapper Bass Distortion is an all-original Fender circuit. The chassis is crafted from lightweight, durable anodized aluminum, and the LED-backlit knobs easily show your control settings at a glance on dark stages.
TRAPPER BASS DISTORTION
DESIGNED IN CALIFORNIA, U.S.A.
Distortion 1 and 2 Footswitches/LEDsThese footswitches bypass or engage each distortion effect. LED illuminates when effect is on.
Output JackLow-impedance output jack connects to amp or to next effect pedal in signal chain.
Sub Level 2Adjusts clean-output volume level from low-pass filter.
Frequency 2Adjusts low-pass frequency. Frequencies below knob setting will be routed around distortion effect, providing a clear, basic tone to layer the distortion on.
Level 2Adjusts output level of Distortion 2.
Tone 2Adjusts brightness of Distortion 2 circuit.
Gain 2Adjusts sustain or drive of Distortion 2 circuit.
Gain 1Adjusts sustain or drive of Distortion 1 circuit.
Tone 1Adjusts brightness of Distortion 1 circuit.
Level 1Adjusts output level of Distortion 1.
Input JackHigh-impedance input suitable for electric guitar, bass, acoustic guitars with pickup systems, keyboards and other instruments.
LED Kill SwitchDeactivates control-knob illumination.
DC Power ConnectorStandard center-negative 9VDC jack for use with appropriate power supplies.
A PRODUCT OFFENDER MUSICAL INSTRUMENTS CORPORATION
CORONA, CALIFORNIA, U.S.A.
Fender® is a registered trademark of FMIC.Copyright © 2020 FMIC. All rights reserved.
PN 7720601000 REV. A
IMPORTANT SAFETY INSTRUCTIONS
•WARNING: To prevent damage, fire or shock hazard, do not expose the unit or its AC power to rain or moisture.•Do not alter the AC plug of the connected power adapter•Do not drip or splash liquids on the unit.•No user serviceable parts inside, refer servicing to qualified personnel only.•WARNING: The unit must only be connected to a safety agency certified, regulated, power source (adapter), approved for use and compliant with applicable local and national regulatory safety requirements.•Unplug AC power adapter before cleaning unit exterior. Use only a damp cloth for cleaning; wait until unit is completely dry before reconnecting to power.•Amplifiers and loudspeaker systems, and ear/headphones (if equipped) are capable of producing very high sound pressure levels, which may cause temporary or permanent hearing damage. Use care when setting and adjusting volume levels during use.
ADDITIONAL LANGUAGES
Manual available in additional languages atwww.fender.com/support
Product specifications subject to change without notice
SPECIFICATIONS
IMPEDANCESPOWER SUPPLY
POWER REQUIREMENTS
DIMENSIONSWEIGHT
Input: 500KΩ Output: 470Ω9VDC regulated adapter, 5.5 x 2.1 mm barrel connector, center negative140mA @ 9VDC
4.84” x 3.74” x 1.77” (123mm x 95mm x 45mm)1.32 lbs. (0.6kg)
NOTES
© FENDER MUSICAL INSTRUMENTS 2020