travel system stroller - babylove · 08 caution b open the frame as shown by the arrows until you...

URBANLITETRAVEL SYSTEM STROLLER

KEEP THESE INSTRUCTIONS FOR FUTURE REFERENCE

Series SH608INSTRUCTION BOOK

ALWAYS FOLLOW THE MANUFACTURERS INSTRUCTIONS.READ ALL INSTRUCTIONS CAREFULLY BEFORE ASSEMBLY AND USEOF THIS STROLLER. THE CORRECT USE AND MAINTENANCE OF THIS PRODUCT ISESSENTIAL.

• USE GREAT CARE WHEN USING THE STROLLER ON STAIRS, ESCALATORS, TRAVELATORS OR OTHER MOVING SURFACES.• IT IS RECOMMENDED TO REMOVE THE CHILD FROM THE STROLLER BEFORE GOING UP OR DOWN STAIRS OR ESCALATORS.• DO NOT LIFT THE STROLLER BY THE ARM BAR (If Supplied) BECAUSE IT MAY DISENGAGE.• DO NOT ALLOW CHILDREN TO STAND ON THE SEAT. • DO NOT HANG BAGS OR GOODS FROM THE HANDLE AS THIS COULD CAUSE THE STROLLER TO TIP OVER.• DO NOT LEAVE THE STROLLER AND ITS ACCESSORIES NEAR AN OPEN FIRE OR EXPOSED FLAME.• DO NOT PLACE MORE THAN 4 KG IN THE BASKET, OR 1KG IN THE CANOPY POCKET (IF SUPPLIED).

IMPORTANT NOTES:

02 www.babylove.com.au

IMPORTANT NOTES

www.babylove.com.au

WARNINGS: TO AVOID INJURY OR DEATH:

ALWAYS APPLY THE BRAKES WHENEVER THE STROLLER ISSTATIONARY.

• DO NOT LEAVE CHILDREN UNATTENDED.• SECURE THE CHILD IN THE HARNESS AT ALL TIMES.• DO NOT CARRY EXTRA CHILDREN OR BAGS ON THIS STROLLER.• MAKE SURE CHILDREN ARE CLEAR OF ANY MOVING PARTS IF YOU ADJUST THE STROLLER.• DO NOT USE ANY ACCESSORIES OTHER THAN THOSE APPROVED FOR USE WITH THIS STROLLER BY BRITAX.• IT IS UNSAFE TO USE ACCESSORIES NOT APPROVED FOR USE WITH THIS STROLLER.• THE MAXIMUM WEIGHT OF THE CHILD USING THIS STROLLER IS NOT TO EXCEED 20 KG.

This CAUTION Symbol is shown at certain steps inthis Instruction Manual to highlight the danger ofbeing injured by moving parts.

CAUTION

FOR IMPORTANT NOTES AND WARNINGS ON ACCESSORIES - REFER TO THEIR INDIVIDUAL SECTIONS IN THIS BOOK. THE MAXIMUM WEIGHT VARIES FOR EACH ACCESSORY.

03www.babylove.com.au

WARNINGS

04

The SMART lifting techniqueThis technique can be used to pick up small light loads from low levels.

Size up the Load • Assess the load (size, shape and weight).• Assess whether the load needs to be moved;• Where is it going to be placed” Check that there are no obstructions;• Assess whether mechanical or human assistance is required.

Move the Load as close to the body as possible• A load is heavier to lift or carry if it is not close to the body.• The whole hand should be used to ensure a firm grip. Always bend your knees• Maintain balance.• Keep feet apart and in a comfortable position.• Minimise lower back bending.• Bend knees preferable at as large an angle as possible but not at a right angle - use a semi squat in preference to a full squat. Raise the load with your legs• Achieve the lift smoothly and without jerkiness.• Maintain the normal curvature of the spine to allow the force of the load to be distributed evenly from the spine to the pelvis. Turn your feet in the direction that you want to move the load• Avoid unnecessary bending, twisting and reaching.• Change direction by turning your feet and not your back.• To set the load down, squat down, keep your head up and let your legs do the work.Remember to ‘THINK TALL’ chest lifted, shoulders relaxed, chintucked in and head level.

www.babylove.com.au

MANUAL HANDLING TECHNIQUES

05

C 1 x Canopy D 1 x Arm bar

www.babylove.com.au

PARTS LIST

A 1 x Frame B 1 x Seat Assembly

E 2 x Front wheels F 2 x Rear wheels

www.babylove.com.au06

I 2 x Car Seat Receiversfor Snap N’ Go Infant Carrier

PARTS LIST

G 1 x Reversible Insert H 1 x Set Shoulder HarnessPads

www.babylove.com.au 07

IMPORTANT NOTES:PLEASE REFER TO PAGE 4 FOR SMART LIFTING TECHNIQUES.

• RELEASE THE STORAGE LATCH WITH DUE CARE AND OPEN THE FRAME.• WHEN OPENING THE STROLLER, BE AWARE OF THE DANGER OF BEING INJURED BY MOVING PARTS AND LOCKING DEVICES DURING THE PROCESS. KEEP ALL HANDS AND LIMBS CLEAR OF THESE PARTS.• THERE IS POTENTIAL FOR FINGERS OR PARTS OF THE BODY TO BE INJURED WHEN THE STROLLER IS BEING UNFOLDED, DUE CARE SHOULD BE EXERCISED.• KEEP CHILDREN CLEAR OF THE STROLLER WHEN UNFOLDING THE STROLLER.• OPEN THE STROLLER SLOWLY AND BE CAREFUL WHERE YOU PLACE YOUR HANDS. KEEPING YOUR HANDS ON THE HANDLE IS THE BEST WAY TO UNFOLD THE STROLLER.

A Release the storage latch located on the rear leg.

1. OPENING THE STROLLER

Storagelatch

A


CAUTION

B Open the frame as shown by the arrows until you hear a ‘click’ which indicates the frame is fully opened and locked. Squeeze in and hold the buttons on the inside of the handle and rotate the handle completely up. Push down on the stroller handle to confirm that the frame is locked.

1. OPENING THE STROLLER

click

B

B


A Take each front swivel wheel assembly and push it into each of the front leg mouldings until you here a ‘click’ which indicates the wheel is locked in. Pull on the wheel assembly to confirm it is securely assembled.

B To remove each front swivel wheel assembly, press the black quick release button on the side of front leg mouldings.

2. ASSEMBLING AND REMOVING THE FRONT SWIVEL WHEELS

clickQuick release

Button

A To fit the rear wheels, insert each wheel axle into the moulding and push in until locked. You should hear a ‘click’ which indicates the wheel has locked in. Pull on the wheel to make sure it is engaged. Repeat the process if not locked in.

B To remove the wheels, pull the metal latch downwards on the underneath of the brake moulding to release the wheel, and then pull wheel off.

3. ASSEMBLING AND REMOVING THE REAR WHEELS

A B

2

1


3. ASSEMBLING AND REMOVING THE REAR WHEELS

A To lock the swivel wheels, push the locking clip down. To allow the wheels to swivel, lift the locking clip up on the front of each wheel.

PLEASE NOTE: Always lock the swivel wheels when using the strolleron rough surfaces as this will minimise wheel wobble.The swivel wheels should only be locked when the wheels are in thetrailing position (wheels under frame).

4. USING THE FRONT SWIVEL WHEELS

A BMetal Latch

A B


5. ATTACHING THE STROLLER SEAT TO THE STROLLER FRAME IN THE FORWARD FACING POSITION

A To secure the seat support bar, raise the seat support bar into the upright position and lift the large fabric flap and place it over the seat support bar and secure with the hook and loop.

THE SEAT SUPPORT BAR ON THE UNDERNEATH OF THE SEAT UNITMUST BE SECURED BEFORE ATTACHING THE SEAT UNIT TO THE STROLLER FRAME.

IMPORTANT NOTE:

SeatSupport

Bar


A Hold the stroller seat over the frame and align the stroller seat mouldings on both sides over the frame connection sockets in the middle of the frame.

ALWAYS REMOVE YOUR CHILD FROM THE STROLLER SEAT BEFOREINSTALLING, REMOVING OR CHANGING THE SEAT DIRECTION.

IMPORTANT NOTE:

C Pull up on both sides of the stroller seat to make sure it is securely locked into the stroller frame.

PLEASE NOTE: See Page 13 for Step B & Step C illustrations.

B Insert the stroller seat mouldings into the frame connection sockets and push down until both seat mouldings until you hear a ‘click’ which indicates the seat mouldings have locked in.

CAUTION

Frameconnection

sockets

Strollerseat

mouldings

CAUTION


CAUTION

click

B C

CAUTION



www.babylove.com.au


IMPORTANT NOTE:

A Press in and hold the red quick release button on both sides of the stroller seat mouldings and lift the stroller seat out of the frame connection sockets.

CAUTION

Frameconnection

sockets

Strollerseat

mouldings

CAUTION

Quickreleasebutton

A A

6. REMOVING THE STROLLER SEAT FROM THE STROLLER FRAME

14


7. ATTACHING THE STROLLER SEAT TO THE STROLLER FRAME IN THE REARWARD FACING POSITION

A Hold the stroller seat over the frame and align the stroller seat mouldings on both sides over the frame connection sockets in the middle of the frame.


IMPORTANT NOTE:

B Insert the stroller seat mouldings into the frame connection sockets and push down until both seat mouldings until you hear a ‘click’ which indicates the seat mouldings have locked in.

C Pull up on both sides of the stroller seat to make sure it is securely locked into the stroller frame.

PLEASE NOTE: See Page 16 for Step B & Step C illustrations

CAUTIONCAUTION

Strollerseat

mouldings

Frameconnection

sockets

A A


7. ATTACHING THE STROLLER SEAT TO THE STROLLER FRAME IN THE REARWARD FACING POSITION

B C

CAUTIONclick

CAUTION


8. ATTACHING AND USING THE CANOPY

The sun is very strong. DO NOT LEAVE YOUR CHILD EXPOSED TO THE SUN. The canopy or hood on this product will not give your child total protection from the harmful rays of the sun.

IMPORTANT NOTE:

A To attach the canopy, slide the canopy mouldings (as indicated by arrow) into the frame mouldings until they lock together.

B To adjust the canopy, open by pulling forward, or close by pushing it backward.


8. ATTACHING AND USING THE CANOPYC To increase the canopy length, open the zipper to access extra canopy section.

D To use the peek a boo window, lift the canopy window flap up.

E To remove the canopy, slide the canopy mouldings (as indicated by arrow) out of the frame mouldings.

C C

Zipper

D E


9. ATTACHING AND REMOVING THE ARM BAR

WARNING: WHEN A CHILD IS IN THE STROLLERKEEP THE ARM BAR ATTACHED TO THE ADAPTORS AT ALLTIMES.

A Align the arm bar pins with the frame mouldings on both sides of the stroller seat and insert until you hear a ‘click’.

B To assist with putting a child in the stroller, release the arm bar on one side, press the red quick release tab located underneath the frame moulding and pull the arm bar out. Rotate the arm bar clear of the stroller. Lock the arm bar back into position after fastening the child in the harness.

C To remove the arm bar, press the red quick release tabs located underneath both frame mouldings and lift the arm bar off the stroller seat .

click Quick release tab

A B/C


10. FITTING THE REVERSIBLE INSERT AND SHOULDER PADS

A Place the insert on the stroller seat and thread the harness shoulder straps through the corresponding slots in the seat insert. Thread the harness waist straps through the lower slots in the back of the seat insert. Pull the crotch buckle through the lower slot in the seat liner. To remove the insert, perform the above actions in the reverse order

B To attach the shoulder pads, release the harness buckles and slide the shoulder pads onto the shoulder harness.

IMPORTANT NOTE:ENSURE THAT THE SHOULDER STRAPS ARE FITTED THROUGH THE APPROPRIATE HARNESS SLOTS TO SUIT YOUR CHILD’S SEATEDSHOULDER HEIGHT.


11. ADJUSTING THE BACKREST

WARNINGS:• THE UPRIGHT POSITIONS ARE NOT SUITABLE FOR USE WITH CHILDREN LESS THAN 6 MONTHS OLD.• THE LOWEST RECLINE POSITION SHOULD BE USED TO TRANSPORT BABIES. THE BACKREST CAN BE ADJUSTED TO A MORE UPRIGHT POSITION AS THE CHILD GROWS OLDER AND IS ABLE TO SUPPORT ITS HEAD WITHOUT ASSISTANCE.

PLEASE NOTE: If the child is sitting in the seat, support the backrestas it reclines. If you have difficulty adjusting the backrest you mayneed to remove the child from the seat to allow you to raise or lower the backrest with ease.

Backrestadjusterbutton

Mainadjuster

moulding


11. ADJUSTING THE BACKRESTA To raise the backrest, grasp the plastic rings fixed to the adjuster straps and with the other hand push the backrest up to the desired position.

B To lower the backrest, support the backrest with one hand and with the other hand pull down the on the backrest adjuster button and lower the backrest to the desired position.


12. USING THE BRAKES

WARNING: ALWAYS APPLY THE BRAKES WHEN THESTROLLER IS STATIONARY.

A To lock the rear wheels, press the brake pedal down. Check that the brakes have locked by trying to push the stroller forward. If not locked, repeat this step. To release the brakes, push the brake pedal up.

13. ADJUSTING THE LEG SUPPORT

IMPORTANT NOTES: • THE LEG SUPPORT FEATURE IS PROVIDED FOR YOUR CHILD'S COMFORT. • THE LEG SUPPORT IS NOT DESIGNED TO SUPPORT EXTRA WEIGHT. • DO NOT ALLOW CHILDREN TO STAND OR SIT ON THE LEG SUPPORT. IT WILL DISENGAGE IF EXTRA WEIGHT IS APPLIED. • IF LEG REST DISENGAGES SIMPLY LIFT UP AGAIN TO RESET LEG SUPPORT.


13. ADJUSTING THE LEG SUPPORTA To adjust the leg rest, press the release buttons in on both sides of the leg rest and raise or lower to your desired position.

22

14. ADJUSTING THE PIVOTAL HANDLEPLEASE NOTE: There are three handle height positions.

A To adjust the handle height, squeeze in and hold the buttons on the inside of the handle. Rotate the handle up or down to the desired position then release the buttons.

Handleadjusting

button

1

2

2


• A five point harness is provided to restrain your child.• Buckle tongues separate for added safety.• To reconnect buckle tongues and to secure the child in the harness please follow the steps below carefully.

• ENSURE YOUR CHILD IS SECURED WITH A CORRECTLY ADJUSTED HARNESS.• THE ADJUSTED HARNESS SHOULD CLOSELY FIT THE CHILD.• NEVER LEAVE THE HARNESS BUCKLED WHEN NOT FITTED TO A CHILD IN THE STROLLER, BECAUSE THE HARNESS CAN FORM LOOPS WHICH MAY POSE A STRANGULATION HAZARD.• WHEN HARNESS IS NOT IN USE, DISCONNECT SHOULDER STRAPS FROM THE WAIST STRAPS AND BUCKLE TO PREVENT STRANGULATION.

WARNING: USE THE HARNESS AT ALL TIMES.

A Always apply the brakes to the stroller when placing the child in the stroller. Slip one shoulder strap over each shoulder. Position crotchstrap between legs.

PLEASE NOTE: Ensure the shoulder straps are not twisted as they become uncomfortable for the child.

15. SECURING YOUR CHILD IN THE HARNESS



Shoulder straps

A

B

ABuckle housing

C

Crotch strap

Waiststrap

Waiststrap

B

B Position the shoulder strap tongue (A) on the top of the waist buckletongue (B) on both sides.

Buckle housing

A B+ A B+C

Crotch strap

Shoulder strap Shoulder strap

Waiststrap

Waiststrap

C Push both buckle tongues (A+B) into the buckle housing (C) until thebuckle tongues lock into position.



Waiststrap

Crotch strap

3 bar slider

3 bar slider3 bar slider

D Tighten or loosen crotch straps by sliding the 3 bar sliders up or down.

4 bar slider

E Tighten or loosen the waist straps, hold and lift the 4 bar slider andthen pull the harness strap to adjust to the desired fit. The waist strapneeds to fit firmly around the child.



F Tighten or loosen the shoulder straps, slide the 3 bar slider up or downto adjust to the desired fit. Always adjust the harness strap whenchanging the seating position of the child.

CAUTION: DO NOT SLIDE 3 BAR SLIDER OVER THESEWN TAB ON SHOULDER HARNESS.

G To release the buckle, squeeze the top and buckle tongues togetherwith enough pressure so the buckle tongues can release from thebuckle housing.



H The stroller seat has 3 sets of harness slots at different heights to accommodate the child. To change the shoulder harness height, push the shoulder harness tongue out of the current harness slot and through the back of the seat.

I To reposition harness, pull the shoulder harness buckle tongue through the desired slot.


16. USING THE TETHER STRAP

WARNINGS: USE THE TETHER STRAP TO STOPTHE STROLLER ROLLING AWAY.

• THE STROLLER IS DESIGNED FOR USE ON FLAT OR GENTLY SLOPING SURFACES, AND MAY BE UNSTABLE ON HIGHER SLOPING AND UNEVEN SURFACES AND USERS SHOULD BE AWARE OF THE POSSIBILITY OF THE STROLLER ROLLING AWAY OR TIPPING OVER. • NEVER LET GO OF THE STROLLER WHEN PARKED ON AN INCLINE OR SLOPING SURFACE. ALWAYS PARK ON A FLAT SURFACE.

A A wrist tether strap is provided near the handle grip. Slide your hand through the tether strap loop whenever you use the stroller. Only remove your hand from the tether strap loop when the brakes have been applied to the stroller wheels.


PLEASE REFER TO PAGE 4 FOR LIFTING TECHNIQUES.

• Always ensure you bend your knees where appropriate and take due care when lifting the frame.

• With your hand through the wrist tether strap loop, push the stroller holding the handle.

• The stroller can be steered in the desired direction - allowing the front wheels to swivel will make this easier.

• The front wheels may wobble or oscillate when walking fast. Locking the front swivel wheels will stop this.

• The stroller can be taken up kerbs by either pressing down on the handles and raising the front wheels or turning the stroller around and pulling the stroller up the kerb.

• Caution is required when pushing the stroller on a steep slope as the stroller may become unstable. Always hold the handles firmly.

• Do not run with the stroller.

• Whenever you stop, always apply the brakes before you leave the stroller.

• Do not hang bags or goods from the handle. Use the storage basket.

17. USING THE STROLLER


18. FOLDING THE STROLLER

IMPORTANT NOTES:PLEASE REFER TO PAGE 4 FOR LIFTING TECHNIQUES.

• REMOVE THE CHILD FROM THE STROLLER BEFORE COMMENCING ANY FOLDING OPERATION.• FOLD THE STROLLER SLOWLY AND BE CAREFUL WHERE YOU PLACE YOUR HANDS.• WHEN FOLDING THE STROLLER, BE AWARE OF THE DANGER OF BEING INJURED BY MOVING PARTS AND LOCKING DEVICES DURING THE PROCESS. KEEP ALL HANDS AND LIMBS CLEAR OF THESE PARTS.• THERE IS POTENTIAL FOR FINGERS OR PARTS OF THE BODY TO BE INJURED WHEN THE STROLLER IS BEING FOLDED, DUE CARE SHOULD BE EXERCISED.• KEEP CHILDREN CLEAR OF THE STROLLER WHEN FOLDING THE STROLLER.

PLEASE NOTE: Before folding the stroller, the stroller seat must be inthe forward facing position on the stroller frame (Refer to Section 5).The Stroller will not fold with the stroller seat in the rearward facingposition on the stroller frame.Alternatively, the stroller seat can be removed from the stroller framebefore folding (Refer to section 6).

A Remove the child from the stroller

B Lock the brakes. (Refer to Section 12A)

C Lock the swivel wheels. (Refer to Section 4A).

D Close the canopy. (Refer to Section 8B).

E Raise the backrest to the fully upright position. (Refer to Section 11A)


18. FOLDING THE STROLLERF Squeeze in and hold the buttons on the inside of the handle (1). Rotate the handle completely down against the backrest then release the buttons. Press the folding lever down (2) and push the handle down (3) towards the rear wheels. Lock the frame together with the storage latch (4).

CAUTION

FoldingLever


• TO AVOID INJURY: BEND YOU KNEES WHEN OPENING, LIFTING, CARRYING, FOLDING, UNFOLDING OR ADJUSTING THE STROLLER OR ANY ACCESSORIES.

IMPORTANT NOTES:PLEASE REFER TO PAGE 4 FOR LIFTING TECHNIQUES.

A Ensure the storage latch is locked onto the frame before lifting thestroller. To lift the stroller, grasp the frame halfway along the stroller,so the stroller is balanced.

19. LIFTING AND CARRYING THE STROLLER


20. INFANT CARRIER WARNINGS AND IMPORTANT NOTES (Infant Carrier sold separately)

• IT IS UNSAFE TO USE ACCESSORIES NOT APPROVED FOR USE WITH THIS STROLLER.• DO NOT USE ANY ACCESSORIES OTHER THAN THOSE APPROVED FOR USE WITH THIS STROLLER BY NURSERY ELEGANCE.• THE MAXIMUM WEIGHT OF THE CHILD USING THE ‘SNAP N GO’ INFANT CARRIER IS NOT TO EXCEED 9KG OR TO EXCEED 700MM IN LENGTH.

• THE ‘SNAP N GO’ INFANT CARRIER IS THE ONLY COMPATIBLE INFANT CARRIER DESIGNED TO FIT THE URBANSWIFT STROLLER.• THE INFANT CARRIER MUST BE CORRECTLY FITTED AND LOCKED ONTO THE STROLLER.• WHEN LOCKED ONTO THE STROLLER FRAME, THE INFANT CARRIER MUST ONLY BE USED IN THE REARWARD FACING POSITION (FACING THE MOTHER), FITTED FACING TOWARD THE STROLLER HANDLE.• SECURE THE CHILD USING THE INFANT CARRIER HARNESS AT ALL TIMES.• DO NOT LEAVE CHILD IN THE INFANT CARRIER FOR EXTENDED PERIODS.• THE INFANT CARRIER IS DESIGNED TO PROVIDE MOBILITY OUTSIDE OF THE CAR BUT IT SHOULD NOT BE USED INSTEAD OF AN APPROPRIATE COT.• THE INFANT CARRIER MUST BE REMOVED FROM THE FRAME BEFORE FOLDING.

WARNINGS:

IMPORTANT NOTES:


20. INFANT CARRIER WARNINGS AND IMPORTANT NOTES (Infant Carrier sold separately)

• THE SUN IS VERY STRONG. DO NOT LEAVE YOUR CHILD EXPOSED TO THE SUN. THE CANOPY OR HOOD ON THIS PRODUCT WILL NOT GIVE YOUR CHILD TOTAL PROTECTION FROM THE HARMFUL RAYS OF THE SUN.

PLEASE NOTE: These Instructions are for installing and removing theInfant Carrier on the stroller frame only. For installing and proper useof the Infant Carrier in the car, please follow the Instruction bookprovided with the Infant Carrier.

IMPORTANT NOTES:


21. ATTACHING THE INFANT CARRIER TO THE STROLLER FRAME (Infant Carrier sold separately)

• THE SUN IS VERY STRONG. DO NOT LEAVE YOUR CHILD EXPOSED TO THE SUN. THE CANOPY OR HOOD ON THIS PRODUCT WILL NOT GIVE YOUR CHILD TOTAL PROTECTION FROM THE HARMFUL RAYS OF THE SUN.

PLEASE NOTE: These Instructions are for installing and removing theInfant Carrier on the stroller frame only. For installing and proper useof the Infant Carrier in the car, please follow the Instruction bookprovided with the Infant Carrier.

A Remove the stroller seat from the frame.(Refer to section 6).

B Take one car seat receiver at a time and insert into the stroller hinge as shown (the large RED button must face the outside of the stroller). Push on the receiver until you a hear a ‘click’ which indicates the receiver has locked in. Pull up on each receiver to make sure it has securely locked in.

IMPORTANT NOTES:

click

Receiver

Car Seat ReceiversFront Back


21. ATTACHING THE INFANT CARRIER TO THE STROLLER FRAME (Infant Carrier sold separately)C With the Infant Carrier handle in the upright position, face the feet end of the Infant Carrier towards the stroller handle. Lower the Infant Carrier into the receivers. Press down firmly on both sides.

CAUTION

click

IMPORTANT NOTE:ENSURE THAT THE INFANT CARRIER IS LOCKED INTO PLACE BYPULLING UP ON BOTH SIDES. DO NOT USE THE INFANT CARRIER IF ITIS NOT CORRECTLY INSTALLED.

PLEASE NOTE: Ensure the baby is secured in the Infant Carrier withthe harness at all times. Refer to the Infant Carrier instructionsregarding placing and securing your baby in the Infant Carrier.The Infant Carrier has been fitted with a hood when using the strollerThe hood may also be used in the car.


22. REMOVING THE INFANT CARRIER FROM THE STROLLER FRAMEA To remove the Infant Carrier from the stroller frame, locate the release latch on the back (head end) of the Infant Carrier. Squeeze up and hold the release latch. Lift the Infant Carrier up by the handle and remove from the stroller.

B To remove the Infant Carrier receivers from the stroller frame, press the red release button in on the outside of the receiver and pull out of the stroller frame hinge.

Release button

40 www.babylove.com.au Art No. 4800325

CARE AND MAINTENANCE• To prolong the life of your stroller keep it clean and do not leave it in the direct sunlight for extended periods of time.

• Remove fabric covers and trims may be cleaned using warm water with household soap or mild detergent. Allow it to dry fully, preferably away from the direct sunlight.

• Non removable fabric covers and trims may be spot cleaned using a damp sponge with soap or a mild detergent. Allow it to dry completely before folding or storing it away.

• In some climates the covers and trims may be affected by mould and mildew. To help prevent this occurring, do not fold or store the product if it is damp or wet. Always store the product in a well ventilated area.

• When using your stroller at the beach - completely clean your stroller afterwards to remove the sand and salt from the mechanisms and wheel assembly. Sand and Salt will cause premature wear and corrosion.

• If there are compression marks on the tyres - Use a domestic hair dryer to gently warm (DO NOT OVERHEAT) the tyre and the compression marks should slowly disappear.

• Always check parts regularly for tightness of screws, nuts and other fasteners - tighten if required. To maintain the safety of your nursery product, seek prompt repairs for bent, torn, worn or broken parts. Use only those parts and accessories approved by Nursery Elegance.

THIS PRODUCT IS NOT INTENDED FOR COMMERCIAL USE.


NOTES

Art No. 4800325_Cwww.babylove.com.au

Customer Service Ph: 1300 131 477 Email: [email protected]

Distributed by:Nursery Elegance Pty. Ltd.

ACN: 122 443 3876 Thorpe Street,

Sunshine, Victoria, 3020, Australia

Due to our continuing program of development, Nursery Elegancereserves the right to alter the specifications, colour or design without any

further notice.

The Babylove trademark is the property of Nursery Elegance Pty. Ltd.

Due to the variations in the style and design of our products theillustrations used in this instruction book are generic.

This product is designed to comply with Australian and New ZealandStandard AS/NZS2088:2013 “Prams and Strollers - Safety Requirements”

2015 Copyright Nursery Elegance Pty. Ltd. Australia

travel system stroller - babylove · 08 caution b open the frame as shown by the arrows until you...

Documents