AD

HE

RE

TR

ON

CO

MP

LE

TE

C

ON

CR

ET

E

PR

OT

EC

TO

RTRON CRETE

C O - P O L Y M E R A C R Y L I C F O R W A T E R P R O O F I N G

DESCRIPTION

Single component TRON CRETE polymer for cement based water proofing composite coating membrane. Provide an effective and economical method of waterproofing to concrete and masonry surface by mixing with cement application by brush. TRON CRETE to be mixed with cement at site and simply brush applied over concrete or masonry surfaces to provide an effective waterproofing membrane. TRON CRETE is a non-toxic, non-flammable and users friendly, provide a tough, impermeable waterproofing membrane. TRON CRETE has an excellent adhesion to concrete and masonry surfaces it protect concrete and masonry from natural elements like wind, rain sunlight. TRON CRETE is a breathable allows inside water vapour to escape.

TRON CRETE can be used for waterproofing as a sandwich layer for terrace, bathroom, balconies, chajja, overhead water tank, tunnels, pools, roof, for external & internal walls.

PRODUCT SPECIFICATION

Nature : Aqueous dispersion of acryl ate/styrene: copolymer

Color& Appearance : White LiquidSolid Content : 28 – 30%Pot life : 30 minutesShelf Life : Minimum 12 months in

sealed container

MIXING RATIO

Bonding Coat : 1 part TRON CRETE: 2 part water 4part Cement

Waterproofing coat : 1 part TRON CRETE: 2 part cement

Initial Setting Time : 24 HoursInitial Curing Time : 72Hours with moist cloth or

water sprayCoverage : Bond coat 15-17 sq.mt./lite

: W a t e r p r o o f i n g c o a t 4 - 5 sq.mt./liter/coat

However the practical consumption varies depending on the texture and porosity of the substrate and application thickness.

Direction of UseSurface preparation

The surface must be free from dust, loose particles, oils, grease, mould releasing agents, fungus, moss, and coating. Clean the surface by scrapping/ sand blasting or grinding. Surface of high suction should be thoroughly dampened before application of bonding coat.

BONDING COAT

To prepare a polymer based bonding coat take 1 part of TRON CRETE: 2 part water : 4 part cement and mix thoroughly the materials thus mixed form a thick slurry of a consistency easily applicable by brush, avoid lump formation. The slurry thus prepared is ready for use as a bonding material. Allow 2-3 hours to get it dry before top coat. The surface on which the bonding coat is to be applied has to be cleaned with a water jet approximately 24 hours Prior to application. This will help in making the substrata slightly moist. After application of slurry on the requisite surface place the next screed or mortar etc.

WATERPROOFING TOP COAT

TRON CRETE an acrylic polymer shall be mixed neat with cement in the ratio of 1 part TRON CRETE: 2 parts Cement respectively, add cement into the polymer, to obtain uniform and consistent slurry avoiding any lump formation by low speed mixture. Do not mix more material than which can be used with in the 20-30 minutes. Keep stirring the material into the container. For best result, wet the surface before coating, apply with a short, stiff bristle brush like a paint to an approx. thickness of 1-2 mm, during the first 12 hours of curing TRON CRETE surface must be protected from abrasion, rain or other adverse condition. No traffic shall be allowed within 48 hours after application. Normally 2 coat of TRON CRETE are recommended, first coat should allow to air dry for 5-6 hours. After application of final coat, initial air drying shall be allowed for 5-6 hours, during this time do not uses water for curing. Moist curing should be done for 24 hours by spraying water on TRON CRETE coating TRON CRETE should be allowed to dry for 72 hours before subjecting it to submersion of water for testing.

Cleaning of Tools& Equipment: Tools and equipment can be easily clean with water.

Safety Precautions: In case of accidental ingestion seek medical advice.

Packing: 20 lrt/ pail

Note: The information submitted in this publication is based our current knowledge and experience. In view of the many factors that may affect processing and application these data do not relieve processors of the responsibility of carrying out their own tests and experiments neither do they simply any legally binding assurance of certain properties or of suitability of specific purpose. It is the responsibility of those whom we supply. Our products to ensure that any proprietary right and existing laws and legislations are observed.

20lrt / PAIL MUST BE STORED IN DRY PLACE.

ADHERETRON COMPLETE CONCRETE PROTECTOR

MALAYSIAwww.adheretron.com.my | e-mail: sales@adheretron.com.my