ts 101 572-2 - v1.2.1 - core network and interoperability ... · etsi 6 etsi ts 101 572-2 v1.2.1...

ETSI TS 101 572-2 V1.2.1 (2014-07)

Core Network and Interoperability Testing (INT); Conformance tests; (3GPP Release 10);

Interworking between SIP-I based circuit-switched core network and other networks;

Part 2: SIP-I/SIP NNI Test Suite Structure and Test Purposes (TSS&TP)

TECHNICAL SPECIFICATION

ETSI

ETSI TS 101 572-2 V1.2.1 (2014-07)2

Reference RTS/INT-00110-2

Keywords SIP, SIP-I, testing, TSS&TP

ETSI

650 Route des Lucioles F-06921 Sophia Antipolis Cedex - FRANCE

Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16

Siret N° 348 623 562 00017 - NAF 742 C

Association à but non lucratif enregistrée à la Sous-Préfecture de Grasse (06) N° 7803/88

Important notice

The present document can be downloaded from: http://www.etsi.org

The present document may be made available in electronic versions and/or in print. The content of any electronic and/or print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any

existing or perceived difference in contents between such versions and/or in print, the only prevailing document is the print of the Portable Document Format (PDF) version kept on a specific network drive within ETSI Secretariat.

Users of the present document should be aware that the document may be subject to revision or change of status. Information on the current status of this and other ETSI documents is available at

http://portal.etsi.org/tb/status/status.asp

If you find errors in the present document, please send your comment to one of the following services: http://portal.etsi.org/chaircor/ETSI_support.asp

Copyright Notification

No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm except as authorized by written permission of ETSI.

The content of the PDF version shall not be modified without the written authorization of ETSI. The copyright and the foregoing restriction extend to reproduction in all media.

© European Telecommunications Standards Institute 2014.

All rights reserved.

DECTTM, PLUGTESTSTM, UMTSTM and the ETSI logo are Trade Marks of ETSI registered for the benefit of its Members. 3GPPTM and LTE™ are Trade Marks of ETSI registered for the benefit of its Members and

of the 3GPP Organizational Partners. GSM® and the GSM logo are Trade Marks registered and owned by the GSM Association.

http://www.etsi.org/

http://portal.etsi.org/tb/status/status.asp

http://portal.etsi.org/chaircor/ETSI_support.asp

ETSI

ETSI TS 101 572-2 V1.2.1 (2014-07)3

Contents

Intellectual Property Rights ................................................................................................................................ 5

Foreword ............................................................................................................................................................. 5

Modal verbs terminology .................................................................................................................................... 5

1 Scope ........................................................................................................................................................ 6

2 References ................................................................................................................................................ 6

2.1 Normative references ......................................................................................................................................... 6

2.2 Informative references ........................................................................................................................................ 6

3 Definitions, symbols and abbreviations ................................................................................................... 7

3.1 Definitions .......................................................................................................................................................... 7

3.2 Symbols .............................................................................................................................................................. 7

3.3 Abbreviations ..................................................................................................................................................... 7

4 Test Suite Structure (TSS) ........................................................................................................................ 7

5 Test Purposes (TP) ................................................................................................................................... 8

5.1 Introduction ........................................................................................................................................................ 8

5.1.1 TP naming convention .................................................................................................................................. 8

5.1.2 Test strategy .................................................................................................................................................. 8

5.1.3 Test purpose structure ................................................................................................................................... 8

6 Test purposes (TP) ................................................................................................................................... 9

6.1 SIP NNI -SIP-I protocol interworking................................................................................................................ 9

6.1.1 Signalling Interworking of a Call from the IP Multimedia Subsystem towards the SIP-I based circuit-switched core network ....................................................................................................................... 9

6.1.1.1 Sending of INVITE (IAM) ...................................................................................................................... 9

6.1.1.2 Sending of UPDATE............................................................................................................................. 35

6.1.1.3 Receipt of multiple INVITE request and in-dialog SIP INFO request .................................................. 37

6.1.1.4 Sending of 18x provisional responses ................................................................................................... 38

6.1.1.5 Sending of the 200 OK (INVITE) ......................................................................................................... 62

6.1.1.6 Sending of the Release message (REL) ................................................................................................ 74

6.1.1.7 Receipt of the Release Message ............................................................................................................ 80

6.1.1.8 Void....................................................................................................................................................... 87

6.1.1.9 Void....................................................................................................................................................... 87

6.1.1.10 Void....................................................................................................................................................... 87

6.1.2 Signalling Interworking of a Call from SIP-I based circuit-switched core network towards the IP Multimedia Subsystem ............................................................................................................................... 87

6.1.2.1 Sending of INVITE ............................................................................................................................... 87

6.1.2.2 Updating Precondition Information .................................................................................................... 106

6.1.2.3 Sending of ACM and awaiting answer indication ............................................................................... 107

6.1.2.4 Sending of the Call Progress message (CPG) ..................................................................................... 124

6.1.2.5 Sending of the Answer Message (ANM) ............................................................................................ 136

6.1.2.6 Sending of the 200 OK (INVITE) with encapsulated Connect message (CON) ................................. 145

6.1.2.7 Receipt of Status Codes 3xx, 4xx, 5xx or 6xx .................................................................................... 153

6.1.2.8 Receipt of a BYE ................................................................................................................................ 163

6.1.2.9 Receipt of the Release Message .......................................................................................................... 167

6.1.2.10 Void..................................................................................................................................................... 173

6.1.2.11 Autonomous Release at O-MGCF ...................................................................................................... 173

6.2 Supplementary Services ................................................................................................................................. 175

6.2.1 Void .......................................................................................................................................................... 175

6.2.2 Connected line presentation and restriction (COLP/COLR) ..................................................................... 175

6.2.3 Malicious call identification ..................................................................................................................... 181

6.2.4 Subaddressing (SUB) ................................................................................................................................ 182

6.2.5 Call Forwarding Busy (CFB)/ Call Forwarding No Reply (CFNR) / Call Forwarding Unconditional (CFU) ........................................................................................................................................................ 188

6.2.6 Explicit Call Transfer (ECT) .................................................................................................................... 191

ETSI

ETSI TS 101 572-2 V1.2.1 (2014-07)4

6.2.7 Void .......................................................................................................................................................... 195

6.2.8 Call Hold ................................................................................................................................................... 195

6.2.9 Call Completion on busy subscriber ......................................................................................................... 208

6.2.10 Completion of Calls on No Reply (CCNR) .............................................................................................. 208

6.2.11 Terminal Portability (TP) .......................................................................................................................... 209

6.2.12 Conference calling (CONF) / Three-Party Service (3PTY) ...................................................................... 210

6.2.13 Void .......................................................................................................................................................... 217

6.2.14 Multi-Level Precedence and Pre-emption (MLPP) ................................................................................... 217

6.2.15 Global Virtual Network Service (GVNS) ................................................................................................. 219

6.2.16 Reverse charging (REV) ........................................................................................................................... 219

6.2.17 Void .......................................................................................................................................................... 222

6.2.18 Void .......................................................................................................................................................... 222

6.3 IMS Supplementary Services ......................................................................................................................... 222

6.3.1 Originating Identification Presentation (OIP) and Originating Identification Restriction (OIR) .............. 222

6.3.2 Terminating Identification Presentation (TIP) and Terminating Identification Restriction (TIR) ............ 247

6.3.3 Communication Diversion (CDIV) ........................................................................................................... 253

6.3.4 Conference call (CONF) ........................................................................................................................... 296

6.3.5 Message Waiting Indication (MWI) ......................................................................................................... 308

6.3.6 Malicious Communication Identification (MCID) ................................................................................... 308

6.3.7 Closed User Group (CUG) ....................................................................................................................... 312

6.3.8 Call Completion Services ......................................................................................................................... 318

6.3.9 Communication Waiting (CW) ................................................................................................................. 338

Annex A (informative): Bibliography ................................................................................................. 340

History ............................................................................................................................................................ 341

ETSI

ETSI TS 101 572-2 V1.2.1 (2014-07)5

Intellectual Property Rights IPRs essential or potentially essential to the present document may have been declared to ETSI. The information pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found in ETSI SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in respect of ETSI standards", which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web server (http://ipr.etsi.org).

Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web server) which are, or may be, or may become, essential to the present document.

Foreword This Technical Specification (TS) has been produced by ETSI Technical Committee Core Network and Interoperability Testing (INT).

The present document is part 2 of a multi-part deliverable covering SIP NNI - SIP-I Interworking described in the clauses 7.2 and 7.3 of TS 129 235 [1] (Release 10), as identified below:

Part 1: "Protocol Implementation Conformance Statement (PICS)";

Part 2: "SIP-I/SIP NNI Test Suite Structure and Test Purposes (TSS&TP)".

Modal verbs terminology In the present document "shall", "shall not", "should", "should not", "may", "may not", "need", "need not", "will", "will not", "can" and "cannot" are to be interpreted as described in clause 3.2 of the ETSI Drafting Rules (Verbal forms for the expression of provisions).

"must" and "must not" are NOT allowed in ETSI deliverables except when used in direct citation.

http://webapp.etsi.org/IPR/home.asp

http://portal.etsi.org/Help/editHelp!/Howtostart/ETSIDraftingRules.aspx

ETSI

ETSI TS 101 572-2 V1.2.1 (2014-07)6

1 Scope The present document specifies the Test Suite Structure and Test Purposes for SIP - SIP-I Interworking described in the clauses 7.2 and 7.3 of TS 129 235 [1] (Release 10).

2 References References are either specific (identified by date of publication and/or edition number or version number) or non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the reference document (including any amendments) applies.

Referenced documents which are not found to be publicly available in the expected location might be found at http://docbox.etsi.org/Reference.

NOTE: While any hyperlinks included in this clause were valid at the time of publication ETSI cannot guarantee their long term validity.

2.1 Normative references The following referenced documents are necessary for the application of the present document.

[1] ETSI TS 129 235 (V10.1.0): "Digital cellular telecommunications system (Phase 2+); Universal Mobile Telecommunications System (UMTS); LTE; Interworking between SIP-I based circuit-switched core network and other networks (3GPP TS 29.235 version 10.1.0 Release 10) ".

[2] ETSI TS 129 163: "Digital cellular telecommunications system (Phase 2+); Universal Mobile Telecommunications System (UMTS); LTE; Interworking between the IP Multimedia (IM) Core Network (CN) subsystem and Circuit Switched (CS) networks (3GPP TS 29.163 Release 8)".

[3] ISO/IEC 9646-1: "Information technology - Open Systems Interconnection - Conformance testing methodology and framework - Part 1: General concepts".

[4] Recommendation ITU-T T.38: "Procedures for real-time Group 3 facsimile communication over IP networks".

[5] Void.

[6] ETSI TS 101 572-1: "Core Network and Interoperability Testing (INT); Conformance tests according to 3GPPTM 29.235 Release 10; Interworking between SIP-I based circuit-switched core network and other networks; Part 1: Protocol Implementation Conformance Statement (PICS)".

2.2 Informative references The following referenced documents are not necessary for the application of the present document but they assist the user with regard to a particular subject area.

[i.1] Recommendation ITU-T E.164: "The international public telecommunication numbering plan".

http://docbox.etsi.org/Reference

ETSI

ETSI TS 101 572-2 V1.2.1 (2014-07)7

3 Definitions, symbols and abbreviations

3.1 Definitions For the purposes of the present document, the terms and definitions given in TS 129 235 [1] and the following apply:

Implementation Under Test (IUT): Refer to ISO/IEC 9646-1 [3].

System Under Test (SUT): Refer to ISO/IEC 9646-1 [3].

Test Purpose (TP): Refer to ISO/IEC 9646-1 [3].

3.2 Symbols For the purposes of the present document, the symbols given in TS 129 235 [1] apply.

3.3 Abbreviations For the purposes of the present document, the abbreviations given in TS 129 235 [1] and the following apply:

ACM Address Complete Message IAM Initial Address Message IUT Implementation Under Test oBCI optional Backward Call Indicator REL RELease message SUT System Under Test TP Test Purpose

4 Test Suite Structure (TSS) The Test Suite Structure is in close alignment with TS 129 235 [1] and TS 129 163 [2].

SIP NNI -SIP-I Basic call Sending_of_INVITE (IAM) TP_101_xxx

TP_102_xxx TP_103_xxx TP_104_xxx TP_105_xxx TP_106_xxx TP_107_xxx

SIP-I –SIP NNI Basic call Sending_of_INVITE TP_201_xxx

TP_202_xxx TP_203_xxx TP_204_xxx TP_205_xxx TP_206_xxx TP_207_xxx TP_208_xxx TP_209_xxx TP_211_xxx

ETSI

ETSI TS 101 572-2 V1.2.1 (2014-07)8

PSTN-SS PSTN-SS/COL TP_302_xxx

PSTN-SS/MCID TP_303_xxx PSTN-SS/SUB TP_304_xxx PSTN-SS/CDIV TP_305_xxx PSTN-SS/ECT TP_306_xxx PSTN-SS/HOLD TP_308_xxx PSTN-SS/CCBS TP_309_xxx PSTN-SS/CCNR TP_310_xxx PSTN-SS/TP TP_311_xxx PSTN-SS/CONF TP_312_xxx PSTN-SS/MLPP TP_314_xxx PSTN-SS/GVNS TP_315_xxx PSTN-SS/REV TP_316_xxx

IMS-SS IMS-SS/OIP-OIR TP_401_xxx

IMS-SS/TIP-TIR TP_402_xxx IMS-SS/CDIV TP_403_xxx PSTN-SS/CONF TP_404_xxx IMS-SS/MCID TP_406_xxx IMS-SS/CUG TP_407_xxx IMS-SS/CC/ TP_408_xxx IMS-SS/CW TP_409_xxx

5 Test Purposes (TP)

5.1 Introduction For each requirement in TS 129 163 [2] a TP is defined.

5.1.1 TP naming convention

TPs are numbered, starting at 001, within each group. Groups are organized according to the TSS. Additional references are added to identify the actual test suite and whether it applies to the network or the user (see table 5.1.1-1).

Table 5.1.1-1: TP identifier naming convention scheme

Identifier: TP_<group>_<nnn> <group> = group 3 digit field representing group reference according to TSS <nnn> = TP number 3 digit sequential number (001 to 999)

5.1.2 Test strategy

As the base standard TS 129 235 [1] and TS 129 163 [2] contains no explicit requirements for testing, the TPs were generated as a result of an analysis of the base standard and the PICS specification TS 101 572-1 [6]. The criteria applied include the following:

• whether or not a test case can be built from the TP is not considered.

5.1.3 Test purpose structure

The test purpose structure is according to the test suite structure (TSS). The Reference column in each Test Purpose refers to the basic specification except stated explicitly.

ETSI

ETSI TS 101 572-2 V1.2.1 (2014-07)9

6 Test purposes (TP)

6.1 SIP NNI -SIP-I protocol interworking

6.1.1 Signalling Interworking of a Call from the IP Multimedia Subsystem towards the SIP-I based circuit-switched core network

6.1.1.1 Sending of INVITE (IAM)

TP number TP_101_001 Reference [1], clause 7.2.1 [2], clause 7.2.3.1.1

TSS reference SIP NNI - SIP-I/Basic call/Sending_of_ SIP-INVITE request / Selection criteria Test Purpose name Sending of SIP-INVITE request Test Purpose Ensure that on reception of a SIP-INVITE requesting a session, the I-MGCF sends a

SIP-INVITE request with encapsulated IAM message. ISUP Parameter values SIP Parameter values Comments Message flows SIP NNI MGCF SIP-I

INVITE � � INVITE (IAM) 100 Trying � � 100 Trying

Apply post test routine

ETSI

ETSI TS 101 572-2 V1.2.1 (2014-07)10

TP number TP_101_002

Reference [1], clause 7.2.4 [2], clause 7.2.3.1.1

TSS reference SIP NNI - SIP-I/Basic call/Sending_of_ SIP-INVITE request / Selection criteria PICS 6.1.1/1 AND PICS 6.2.1/1 AND PICS 6.2.1/2 Test Purpose name Preconditions support indicated in the Supported header Test Purpose Ensure that the Preconditions procedure is successful if the support of Precondition is

indicated in the Supported header. The INVITE with encapsulated IAM is immediately sent. The Nature of connection indicator is set to 'continuity check performed on a previous circuit' or 'continuity check required'. After the UPDATE was received, a UPDATE is sent

ISUP Parameter values IAM: Nature of connection indicator = 'continuity check performed on a previous circuit' or 'continuity check required'

SIP Parameter values INVITE: Supported: precondition, 100rel SDP a=curr:qos local none a=curr:qos remote none a=des:qos mandatory local sendrecv a=des:qos none remote sendrecv 183: Require: 100rel SDP a=curr:qos local none a=curr:qos remote none a=des:qos mandatory local sendrecv a=des:qos mandatory remote sendrecv a=conf:qos remote sendrecv UPDATE: SDP a=curr:qos local sendrecv a=curr:qos remote none a=des:qos mandatory local sendrecv a=des:qos mandatory remote sendrecv 200 OK UPDATE SDP a=curr:qos local sendrecv a=curr:qos remote sendrecv a=des:qos mandatory local sendrecv a=des:qos mandatory remote sendrecv

Comments Message flows SIP NNI MGCF SIP-I

INVITE � � INVITE (IAM) 100 Trying � � 100 Trying 183 Session Progress � � 183 Session Progress PRACK � � PRACK 200 OK (PRACK) � � 200 OK (PRACK) UPDATE � � UPDATE 200 OK (UPDATE) � � 200 OK (UPDATE)


ETSI

ETSI TS 101 572-2 V1.2.1 (2014-07)11

TP number TP_101_003

Reference [1], clause 7.2.4 [2], clause 7.2.3.1.1

TSS reference SIP NNI - SIP-I/Basic call/Sending_of_ SIP-INVITE request / Selection criteria PICS 6.1.1/1 AND PICS 6.2.1/1 AND NOT PICS 6.2.1/2 Test Purpose name Preconditions support indicated in the Supported header Test Purpose Ensure that the Preconditions procedure is successful if the support of Precondition is

indicated in the Supported header. The INVITE with encapsulated IAM is sent after the UPDATE was received. The Nature of connection indicator is set to 'continuity check is not required'.

ISUP Parameter values IAM: Nature of connection indicator = 'continuity check is not required' SIP Parameter values INVITE: Supported: precondition, 100rel

SDP a=curr:qos local none a=curr:qos remote none a=des:qos mandatory local sendrecv a=des:qos none remote sendrecv 183: Require: 100rel SDP a=curr:qos local none a=curr:qos remote none a=des:qos mandatory local sendrecv a=des:qos mandatory remote sendrecv a=conf:qos remote sendrecv UPDATE: SDP a=curr:qos local sendrecv a=curr:qos remote none a=des:qos mandatory local sendrecv a=des:qos mandatory remote sendrecv 200 OK UPDATE SDP a=curr:qos local sendrecv a=curr:qos remote sendrecv a=des:qos mandatory local sendrecv a=des:qos mandatory remote sendrecv


INVITE � 100 Trying � 183 Session Progress � PRACK � 200 OK (PRACK) � UPDATE � � INVITE (IAM) 200 OK (UPDATE) �


ETSI

ETSI TS 101 572-2 V1.2.1 (2014-07)12

TP number TP_101_006 Reference [1], clause 7.2.4 [2], clause 73.3.1.1

TSS reference SIP NNI - SIP-I/Basic call/Sending_of_ SIP-INVITE request / Selection criteria PICS 6.1.1/2 AND PICS 6.2.1/1 AND PICS 6.2.1/2; BICC support Test Purpose name Preconditions support indicated in the Supported header COT procedure supported Test Purpose Ensure that the Preconditions procedure is successful if the support of Precondition is

indicated in the Supported header. The internal ISUP Continuity check procedure is not supported. The INVITE with encapsulated IAM is immediately sent. The Nature of connection indicator is set to 'COT to be expected'. After the UPDATE was received, an UPDATE is sent

ISUP Parameter values IAM: Nature of connection indicator = 'COT to be expected' SIP Parameter values INVITE: Supported: precondition, 100rel





ETSI

ETSI TS 101 572-2 V1.2.1 (2014-07)13


TSS reference SIP NNI - SIP-I/Basic call/Sending_of_ SIP-INVITE request / Selection criteria PICS 6.1.1/2 AND PICS 6.2.1/1 AND NOT PICS 6.2.1/2 Test Purpose name Preconditions support indicated in the Supported header Test Purpose Ensure that the Preconditions procedure is successful if the support of Precondition is

indicated in the Supported header. The INVITE with encapsulated IAM) is sent after the UPDATE was received. The Nature of connection indicator is set to 'no COT to be expected'.

ISUP Parameter values IAM: Nature of connection indicator = 'no COT to be expected' SIP Parameter values INVITE: Supported: precondition, 100rel



INVITE � 100 Trying � 183 Session Progress � PRACK � 200 OK (PRACK) � UPDATE � � INVITE (IAM) 200 OK (UPDATE) �


ETSI

ETSI TS 101 572-2 V1.2.1 (2014-07)14

TP number TP_101_007A Reference [1], clause 7.2.4 [2], clause 7.3.3.1.1

TSS reference SIP NNI - SIP-I/Basic call/Sending_of_ SIP-INVITE request / Selection criteria PICS 6.2.1/1 AND PICS 6.2.1/2 Test Purpose name Preconditions fulfilled indicated in the INVITE request Test Purpose Ensure that Preconditions are fulfilled is indicated in the SDP received in the INVITE

request. The INVITE with encapsulated IAM) is sent. The Nature of connection indicator is set to 'no COT to be expected'.

ISUP Parameter values IAM: Nature of connection indicator = 'continuity check is not required' or IAM: Nature of connection indicator = 'no COT to be expected'

SIP Parameter values INVITE: Supported: precondition, 100rel SDP a=curr:qos local sendrecv a=curr:qos remote none a=des:qos mandatory local sendrecv a=des:qos none remote sendrecv 180 SDP a=curr:qos local sendrecv a=curr:qos remote sendrecv a=des:qos mandatory local sendrecv a=des:qos mandatory remote sendrecv


INVITE � � INVITE (IAM) 180 Ringing � � 180 Ringing (ACM) PRACK � � PRACK 200 OK (PRACK) � � 200 OK (PRACK)



TSS reference SIP NNI - SIP-I/Basic call/Sending_of_ SIP-INVITE request / Selection criteria Test Purpose name Unsupported media type is rejected 488 is sent Test Purpose Ensure that an unsupported media type is rejected a 488 Not Acceptable Here final

response is sent to the calling user. ISUP Parameter values SIP Parameter values INVITE:

SDP: m= video 4713 RTP/AVP 31 Comments Message flows SIP NNI MGCF SIP-I

INVITE � 488 Not Acceptable Here � ACK �

ETSI

ETSI TS 101 572-2 V1.2.1 (2014-07)15


TSS reference SIP NNI - SIP-I/Basic call/Sending_of_ SIP-INVITE request / Selection criteria Test Purpose name Unsupported media type is rejected session successful Test Purpose Ensure that an unsupported media type is rejected. The SUT sends in the SDP answer the

port number '0' for the concerned media type. ISUP Parameter values SIP Parameter values INVITE:

SDP: m=audio 4711 RTP/AVP 8 m= video 4713 RTP/AVP 31 180 Ringing or 183 Session Progress SDP: m=audio <appropriate Port #> RTP/AVP 8 m=video 0 RTP/AVP 31


INVITE � � INVITE (IAM) 100 Trying � CASE A 180 Ringing � � 180 Ringing (ACM) CASE B 183 Session Progress � � 183 Session Progress

(ACM) Apply post test routine


TSS reference SIP NNI - SIP-I/Basic call/Sending_of_ SIP-INVITE request / Selection criteria Test Purpose name Unsupported codec is deselected Test Purpose Ensure that the SUT removes a codec from the codec list in the SDP answer if the codec is

an unsupported codec. ISUP Parameter values SIP Parameter values INVITE:

SDP: m=audio 4711 RTP/AVP <unsupported codec> 8 180 Ringing or 183 Session Progress SDP: m=audio <appropriate Port #> RTP/AVP 8




ETSI

ETSI TS 101 572-2 V1.2.1 (2014-07)16


TSS reference SIP NNI - SIP-I/Basic call/Sending_of_ SIP-INVITE request / Selection criteria Test Purpose name INVITE request without SDP offer received Test Purpose Ensure that on receipt of an INVITE request without a SDP offer, the SUT sends a SDP

offer in the first reliable non-failure message. ISUP Parameter values SIP Parameter values INVITE: Supported: 100rel

180 Ringing or 183 Session Progress SDP: m=audio 4711 RTP/AVP 8


INVITE � � INVITE (IAM) 100 Trying � CASE A 180 Ringing � � 180 Ringing (ACM) PRACK � � PRACK 200 OK PRACK � � 200 OK PRACK CASE B 183 Session Progress � � 183 Session Progress

(ACM) PRACK � � PRACK 200 OK PRACK � � 200 OK PRACK



TSS reference SIP NNI - SIP-I/Basic call/Sending_of_ SIP-INVITE request / Selection criteria Test Purpose name To header tag is sent in the first provisional response Test Purpose Ensure that a To header tag is contained in the first provisional response ISUP Parameter values SIP Parameter values INVITE: To: <URI>

180 Ringing or 183 Session Progress: To: <URI>; <tag>




ETSI

ETSI TS 101 572-2 V1.2.1 (2014-07)17


TSS reference SIP NNI - SIP-I/Basic call/Sending_of_ SIP-INVITE request / Selection criteria Test Purpose name Coding of called party number Test Purpose Ensure that an INVITE with encapsulated IAM is sent after an INVITE request was

received. In the encapsulated IAM • In case of the 'CC' of the received INVITE request URI is equal to the country code in

which the next hop terminates: remove 'CC' from the user info and send the remaining part as digits in the called party number. The nature of address indicator is set to 'National (Significant) number'.

• In case of the 'CC' of the received INVITE request URI is not equal to the country code in which the next hop terminates: send the unchanged part of the request URI without '+' as digits in the called party number. The nature of address indicator is set to 'International number'.

The internal Network Number Indicator = 'routing to internal network number not allowed' Numbering Plan Indicator = 'ISDN (Telephony) numbering plan (Recommendation E.164 [i.1])'

ISUP Parameter values SIP Parameter values Comments Message flows SIP NNI MGCF SIP-I

INVITE � � INVITE (IAM) 100 Trying �


TP number TP_101_016 Reference [1], clause 7.2.1 [2], clause 7.2.3.1.2.1

TSS reference SIP NNI - SIP-I/Basic call/Sending_of_ SIP-INVITE request / Selection criteria PICS 6.2.1/21 Test Purpose name SendingCompleteIndication is mapped into a hex digit 'F' in the called party number Test Purpose Ensure that on receipt of a PSTN XML SendingCompleteIndication element a hex digit 'F'

is sent al last digit in the called party number ISUP Parameter values SIP Parameter values Comments Message flows SIP NNI MGCF SIP-I




TSS reference SIP NNI - SIP-I/Basic call/Sending_of_ SIP-INVITE request / Selection criteria PICS 6.1.1/1 Test Purpose name Nature of connection indicator Test Purpose Ensure that an INVITE with encapsulated IAM is sent after an INVITE request was

received. The nature of connection indicator in the encapsulated IAM is set Satellite indicator = 'no satellite circuit in the connection' Continuity check indicator = 'continuity check not required' or 'continuity check required' or 'continuity check performed on a previous circuit' Echo control device indicator • TMR audio 3,1 kHz or speech = outgoing echo control device included • TMR 64 kBit/s or HLC 'Facsimile Group 2/3' = 'outgoing echo control device not

included' ISUP Parameter values SIP Parameter values Comments Message flows SIP NNI MGCF SIP-I



ETSI

ETSI TS 101 572-2 V1.2.1 (2014-07)18


TSS reference SIP NNI - SIP-I/Basic call/Sending_of_ SIP-INVITE request / Selection criteria PICS 6.1.1/2 Test Purpose name Nature of connection indicator Test Purpose Ensure that an INVITE with encapsulated IAM is sent after an INVITE request was

received. In the encapsulated IAM the nature of connection indicator is set Satellite indicator = 'no satellite circuit in the connection' Continuity check indicator = 'no COT to be expected or 'COT to be expected' Echo control device indicator = outgoing echo control device included





TSS reference SIP NNI - SIP-I/Basic call/Sending_of_ SIP-INVITE request / Selection criteria NOT PICS 6.2.1/5 Test Purpose name Forward Call indicator Test Purpose Ensure that an INITE (IAM) is sent after an INVITE request was received. If no PSTN XML

attachment is present and the TMR is set to audio, the Forward call indicator is coded as follows: • End-to-end method indicator = ('00') no end-to-end method available (only link-by-link

method available) • Interworking indicator = ('1') interworking encountered • End-to-end information indicator = ('0') no end-to-end information available • ISDN user part/BICC indicator = ('0') ISDN user part/BICC not used all the way • ISDN user part/BICC preference indicator = ('01') ISDN user part/BICC not required all

the way • ISDN access indicator = ('0') originating access non-ISDN • SCCP method indicator = ('00') no indication




ETSI

ETSI TS 101 572-2 V1.2.1 (2014-07)19


TSS reference SIP NNI - SIP-I/Basic call/Sending_of_ SIP-INVITE request / Selection criteria NOT PICS 6.2.1/5 AND NOT PICS 6.2.1/6 Test Purpose name Forward Call indicator Test Purpose Ensure that an INVITE with encapsulated IAM is sent after an INVITE request was

received. If no PSTN XML attachment is present and the TMR 64 kBit/s has no impact of the coding of the Forward call indicator. The Forward call indicator is coded as follows: • End-to-end method indicator = ('00') no end-to-end method available (only link-by-link

method available) • Interworking indicator = ('1') interworking encountered • End-to-end information indicator = ('0') no end-to-end information available • ISDN user part/BICC indicator = ('0') ISDN user part/BICC not used all the way • ISDN user part/BICC preference indicator = ('01') ISDN user part/BICC not required all

the way • ISDN access indicator = ('0') originating access non-ISDN • SCCP method indicator = ('00') no indication





TSS reference SIP NNI - SIP-I/Basic call/Sending_of_ SIP-INVITE request / Selection criteria NOT PICS 6.2.1/5 AND PICS 6.2.1/6 Test Purpose name Forward Call indicator Test Purpose Ensure that an INVITE with encapsulated IAM is sent after an INVITE request was

received. If no PSTN XML attachment is present and the TMR 64 kBit/s has impact of the coding of the Forward call indicator, the Forward call indicator is coded as follows: • End-to-end method indicator = ('00') no end-to-end method available (only link-by-link

method available) • Interworking indicator = ('0') no interworking encountered • End-to-end information indicator = ('0') no end-to-end information available • ISDN user part/BICC indicator = ('1') ISDN user part/BICC used all the way • ISDN user part/BICC preference indicator = ('01') ISDN user part/BICC not required all

the way • ISDN access indicator = ('1') originating access ISDN • SCCP method indicator = ('00') no indication




ETSI

ETSI TS 101 572-2 V1.2.1 (2014-07)20


TSS reference SIP NNI - SIP-I/Basic call/Sending_of_ SIP-INVITE request / Selection criteria PICS 6.2.1/5 Test Purpose name Forward Call indicator Test Purpose Ensure that an INVITE with encapsulated IAM is sent after an INVITE request was

received. If the PSTN XML attachment is present the ProgressIndicator value ProgressDescription = 6, the Forward call indicator is coded as follows: • End-to-end method indicator = ('00') no end-to-end method available (only link-by-link

method available) • Interworking indicator = ('0') no interworking encountered • End-to-end information indicator = ('0') no end-to-end information available • ISDN user part/BICC indicator = ('1') ISDN user part/BICC used all the way • ISDN user part/BICC preference indicator = ('01') ISDN user part/BICC not required all

the way • ISDN access indicator = ('1') originating access ISDN • SCCP method indicator = ('00') no indication

ISUP Parameter values IAM: Forward call indicator SIP Parameter values INVITE:

PSTM XML MIME body <?xml version="1.0" encoding="utf-8"?> PSTN ProgressIndicator ProgressOctet3 CodingStandard>00< Location>yyyy< ProgressOctet4 ProgressDescription>0000110<





TSS reference SIP NNI - SIP-I/Basic call/Sending_of_ SIP-INVITE request / Selection criteria Test Purpose name Mapping of calling party category Test Purpose Ensure that a cpc parameter SIP_CPC received in the P-Asserted-Identity URI parameter

and the "language" in the Accept-Language SIP_LANG header is mapped into the calling party parameter category ISUP_CPC in the sent IAM. The mapping is described in table 6.1.1.1-1

ISUP Parameter values IAM: Calling Party Category = ISUP_CPC SIP Parameter values INVITE: P-Asserted-Identity ;cpc= PARAM, / Accept-Language = SIP_LANG

INVITE (IAM): P-Asserted-Identity; Comments Message flows SIP NNI MGCF SIP-I



ETSI

ETSI TS 101 572-2 V1.2.1 (2014-07)21

Table 6.1.1.1-1: Coding of calling party category

Values for test purposes TP101032 SIP_CPC ISUP_CPC cpc received in a

P-Asserted-Identity PARAM Accept-Language

SIP_LANG Sent Calling party's category

VA_01 operator fr operator, language French VA_02 operator en operator, language English VA_03 operator de operator, language German VA_04 operator ru operator, language Russian VA_05 operator es operator, language Spanish VA_06 ordinary ordinary calling subscriber VA_07 test test call VA_08 payphone payphone VA_09 mobile-hplmn mobile terminal located in the home PLMN VA_10 mobile-vplmn mobile terminal located in a visited PLMN VA_11 unknown calling party's category unknown at this time

(national use VA_12 emergency emergency service call


TSS reference SIP NNI - SIP-I/Basic call/Sending_of_ SIP-INVITE request / Selection criteria PICS 6.2.4/6 Test Purpose name G.177 µ-law: Coding of TMR Test Purpose Ensure that an INVITE with encapsulated IAM is sent after an INVITE request was

received. The Transmission Medium Requirement parameter in the INVITE with encapsulated IAM is set to '3,1 kHz audio' derived from the codec PCMU.

ISUP Parameter values IAM: TMR 3,1 kHz audio

SIP Parameter values INVITE: SDP m=audio <port #> RTP/AVP 0 or <dynamic-PT> a=rtpmap:0 PCMU/8000 or rtpmap: <dynamic-PT> PCMU/8000




TP number TP_101_024A Reference [1], clause 7.2.1 [2], clause 7.2.3.1.2.5

TSS reference SIP NNI - SIP-I/Basic call/Sending_of_ SIP-INVITE request / Selection criteria PICS 6.2.4/5 Test Purpose name G.177 a-law: Coding of TMR Test Purpose Ensure that an INVITE with encapsulated IAM is sent after an INVITE request was

received. The Transmission Medium Requirement parameter in the INVITE with encapsulated IAM is set to '3,1 kHz audio' derived from the codec PCMA.


SIP Parameter values INVITE: SDP m=audio <port #> RTP/AVP 8 or <dynamic-PT> a=rtpmap:8 PCMA/8000 or rtpmap: <dynamic-PT> PCMA/8000




ETSI

ETSI TS 101 572-2 V1.2.1 (2014-07)22

TP number TP_101_024B Reference [1], clause 7.2.1 [2], clause 7.2.3.1.2.5

TSS reference SIP NNI - SIP-I/Basic call/Sending_of_ SIP-INVITE request / Selection criteria PICS 6.2.4/1 Test Purpose name CLEARMODE: Coding of TMR Test Purpose Ensure that an INVITE with encapsulated IAM is sent after an INVITE request was

received. The Transmission Medium Requirement parameter in the INVITE with encapsulated IAM is set to '64 kBit/s unrestricted' derived from the CLEARMODE codec.

ISUP Parameter values IAM: TMR 64 kBit/s unrestricted

SIP Parameter values INVITE: SDP m=audio <port #> RTP/AVP <dynamic-PT> a=rtpmap: <dynamic-PT> CLEARMODE/8000




TP number TP_101_024C Reference [1], clause 7.2.1 [2], clause 7.2.3.1.2.5

TSS reference SIP NNI - SIP-I/Basic call/Sending_of_ SIP-INVITE request / Selection criteria PICS 6.2.4/7 Test Purpose name CLEARMODE: Coding of TMR Test Purpose Ensure that an INVITE with encapsulated IAM is sent after an INVITE request was

received. The Transmission Medium Requirement parameter in the INVITE with encapsulated IAM is set to '64 kBit/s unrestricted' derived from the CLEARMODE codec.


SIP Parameter values INVITE: SDP m=image 4<port #> udptl t38 or tcptl t38 a=[Based on ITU-T T.38 [4]]




ETSI

ETSI TS 101 572-2 V1.2.1 (2014-07)23


TSS reference SIP NNI - SIP-I/Basic call/Sending_of_ SIP-INVITE request / Selection criteria PICS 6.2.4/1 Test Purpose name CLEARMODE: Coding of USI Test Purpose Ensure that an INVITE with encapsulated IAM is sent after an INVITE request was

received. The User service Information parameter in the IAM is set to 'Unrestricted digital information' or 'Unrestricted digital inf. w/tones/ann' if the first stated codec was set to CLEARMODE.

ISUP Parameter values IAM: USI Information Transport Capability Unrestricted digital information or Unrestricted digital inf. w/tones/ann

SIP Parameter values INVITE: SDP m=audio <port #> RTP/AVP <dynamic-PT> a=rtpmap: <dynamic-PT> CLEARMODE/8000





TSS reference SIP NNI - SIP-I/Basic call/Sending_of_ SIP-INVITE request / Selection criteria PICS 6.2.4/7 Test Purpose name Fax T.38: Coding of USI Test Purpose Ensure that an INVITE with encapsulated IAM is sent after an INVITE request was

received. The User service Information parameter in the IAM is set to 'Unrestricted digital information' or 'Unrestricted digital inf. w/tones/ann' if the first stated codec was set to CLEARMODE.

ISUP Parameter values IAM: USI Information Transport Capability 3,1 kHz audio

SIP Parameter values INVITE: SDP m=image 4<port #> udptl t38 or tcptl t38 a=[Based on ITU-T T.38 [4]]




Table 6.1.1.1-3: Void

ETSI

ETSI TS 101 572-2 V1.2.1 (2014-07)24


TSS reference SIP NNI - SIP-I/Basic call/Sending_of_ SIP-INVITE request / Selection criteria Test Purpose name Coding of HLC Test Purpose Ensure that an INVITE with encapsulated IAM is sent after an INVITE request was

received. The High Layer Compatibility parameter in the IAM is set according the mapping described in table 6.1.1.1-4

ISUP Parameter values IAM: HLC

SIP Parameter values INVITE: SDP m line a attributes


INVITE � � IAM 100 Trying �


Table 6.1.1.1-4: Coding of HLC

HLC_VA m= line a= line HLC parameter (optional) <media> <transport> <fmt-list> rtpmap:<dynamic-PT>

<encoding name> <clock rate>[<encoding parameters>]

High Layer Characteristics Identification

VA_01 image Udptl t38 Based on Recommendation ITU-T T.38 [4]

"Facsímile Group 2/3"

VA_02 image tcptl t38 Based on Recommendation ITU-T T.38 [4]

"Facsímile Group 2/3"


TSS reference SIP NNI - SIP-I/Basic call/Sending_of_ SIP-INVITE request / Selection criteria PICS 6.2.1/5 Test Purpose name Mapping of PSTN XML HighLayerCompatibility Test Purpose Ensure that on receipt of a PSTN XML attachment in an INVITE request containing a

HighLayerCompatibility element, this information is mapped into a High Layer Compatibility IE present in an ISUP Access Transport Parameter the High Layer Characteristics value is derived from the PSTN XMLHighLayerCharacteristics element

ISUP Parameter values IAM: ATP High Layer Compatibility High Layer Characteristics>HLC_value

SIP Parameter values INVITE: PSTN XML MIME body <?xml version="1.0" encoding="utf-8"?> PSTN HighLayerCompatibility HLOctet3 CodingStandard>00< Interpretation>100< PresentationMethod>01< HLOctet4 HighLayerCharacteristics>HLC_value<




ETSI

ETSI TS 101 572-2 V1.2.1 (2014-07)25

Table 6.1.1.1-5: Mapping of PSTN XML HighLayerCharacteristic to ISUP ATP High layer compatibility

HLC_value XML HighLayerCharacteristic DSS1 High layer characteristics identification HLC_VA_1 '0000001' Telephony HLC_VA_2 '0000100' Facsimile Group 2/3 HLC_VA_3 '0100001' Facsimile Group 4 Class I HLC_VA_4 '0100100' Facsimile service Group 4, Classes II and III HLC_VA_5 '0110010' Syntax based Videotex HLC_VA_6 '0110011' International Videotex interworking via gateways or

interworking units HLC_VA_7 '0110101' Telex service HLC_VA_8 '1000010' FTAM application HLC_VA_9 '1100000' Videotelephony


TSS reference SIP NNI - SIP-I/Basic call/Sending_of_ SIP-INVITE request / Selection criteria PICS 6.2.1/5 Test Purpose name Mapping of PSTN XML LowLayerCompatibility Test Purpose Ensure that on receipt of a PSTN XML attachment in an INVITE request containing a

LowLayerCompatibility element, this information is mapped into a Low Layer Compatibility IE present in an ISUP Access Transport Parameter the Information Transfer Capability value is derived from the PSTN XMLInformationTransferCapability element

ISUP Parameter values IAM: ATP Low Layer Compatibility InformationTransferCapability=ITC_VA

SIP Parameter values INVITE: <?xml version="1.0" encoding="utf-8"?> PSTN LowLayerCompatibility> LLOctet3> CodingStandard>00< InformationTransferCapability>ITC_VA< LLOctet4> TransferMode>00< InformationTransferRate>10000<




Table 6.1.1.1-6: Mapping of PSTN XML LowLayerCompatibility to ISUP ATP Low Layer Compatibility

ITC_value XML LLC InformationTransferCapability LLC Information transfer capability ITC_VA_1 '00000' Speech ITC_VA_2 '10000' 3,1 kHz audio ITC_VA_3 '01001' Unrestricted digital info ITC_VA_3 '10001' 7 kHz audio

ETSI

ETSI TS 101 572-2 V1.2.1 (2014-07)26


TSS reference SIP NNI - SIP-I/Basic call/Sending_of_ SIP-INVITE request / Selection criteria PICS 6.2.1/5 Test Purpose name Mapping of PSTN XML BearerCapability into TMR and USI Test Purpose Ensure that on receipt of a PSTN XML attachment in an INVITE request containing a

BearerCapability element, this information is mapped into a User Service Information Parameter the Information Transfer Capability value is derived from the PSTN XMLInformationTransferCapability element

ISUP Parameter values IAM: USI Information Transfer Capability=ITC_value

SIP Parameter values <?xml version="1.0" encoding="utf-8"?> PSTN BearerCapability BCoctet3 CodingStandard>00< InformationTransferCapability>ITC_value< BCoctet4 TransferMode>00< InformationTransferRate>10000< BCoctet5 Layer1Identification>01< UserInfoLayer1Protocol>00011<




Table 6.1.1.1-7: Mapping of PSTN XML BearerCapability to ISUP User Service Information

ITC_value XML InformationTransferCapability USI Information transfer capability ITC_VA_1 '00000' Speech ITC_VA_2 '10000' 3,1 kHz audio ITC_VA_3 '01000' unrestricted digital information

ETSI

ETSI TS 101 572-2 V1.2.1 (2014-07)27


TSS reference SIP NNI - SIP-I/Basic call/Sending_of_ SIP-INVITE request / Selection criteria PICS 6.2.1/5AND PICS 6.2.1/7 Test Purpose name Mapping of PSTN XML HighLayerCompatibility into User Teleservice Information

parameter Test Purpose Ensure that on receipt of a PSTN XML attachment in an INVITE request containing a

HighLayerCompatibility element, this information is mapped into a User Teleservice Information parameter the High Layer Characteristics value is derived from the PSTN XML HighLayerCharacteristics element

ISUP Parameter values IAM: UTI High Layer Characteristics>HLC_value





Table 6.1.1.1-8: Mapping of PSTN XML HighLayerCharacteristic to ISUP User Teleservice Information

HLC_value XML HighLayerCharacteristic DSS1 High layer characteristics identification HLC_VA_1 '0000001' Telephony HLC_VA_2 '0000100' Facsimile Group 2/3 HLC_VA_3 '0100001' Facsimile Group 4 Class I HLC_VA_4 '0100100' Facsimile service Group 4, Classes II and III HLC_VA_5 '0110010' Syntax based Videotex HLC_VA_6 '0110011' International Videotex interworking via gateways or

interworking units HLC_VA_7 '0110101' Telex service HLC_VA_8 '1000010' FTAM application HLC_VA_9 '1100000' Videotelephony

ETSI

ETSI TS 101 572-2 V1.2.1 (2014-07)28

TP number TP_101_031 Reference [1], clause 7.2.1 [2], clause 7.2.3.1.2.5a

TSS reference SIP NNI - SIP-I/Basic call/Sending_of_ SIP-INVITE request / Selection criteria PICS 6.2.1/5 Test Purpose name Fall Back connection type is sent Test Purpose Ensure that on receipt of two BearerCapability elements in a INVITE PSTN XML MIME

body • The first stated codec in the SDP m line is the equivalent to the second

BearerCapability element, the BearerCapability element is mapped into the User Service prime (USI prime) parameter in the sent IAM, the TMR is set according the second PSTN XML InformationTransferCapability value

• The second stated codec in the SDP m line is the equivalent to the first BearerCapability element, the BearerCapability element is mapped into the User Service Information (USI) parameter in the sent IAM, the TMR prime is set according the first PSTN XML InformationTransferCapability value

ISUP Parameter values IAM: TMR = second InformationTransferCapability TMR prime = first InformationTransferCapability USI = first BearerCapability USI prime = second BearerCapability

SIP Parameter values INVITE: PSTN XML MIME body <?xml version="1.0" encoding="utf-8"?> PSTN BearerCapability BCoctet3 CodingStandard>00< InformationTransferCapability>00000< or InformationTransferCapability>10000< …. BearerCapability BCoctet3 CodingStandard>00< InformationTransferCapability>10001< ….

Comments SDP: m line contains as the first codec CLEARMODE and as the second codec a G.711 codec

Message flows SIP NNI MGCF SIP-I INVITE � � INVITE (IAM) 100 Trying �


ETSI

ETSI TS 101 572-2 V1.2.1 (2014-07)29

TP number TP_101_032 Reference [1], clause 7.2.1 [2], clause 7.2.3.1.2.5a

TSS reference SIP NNI - SIP-I/Basic call/Sending_of_ SIP-INVITE request / Selection criteria PICS 6.2.1/5 Test Purpose name Fall Back connection type is not sent Test Purpose Ensure that on receipt of two BearerCapability elements in a INVITE PSTN XML MIME

body • The first stated codec in the SDP m line is the equivalent to the second

BearerCapability element, the BearerCapability element is mapped into the User Service prime (USI prime) parameter in the sent IAM, the TMR is set according the second PSTN XML InformationTransferCapability value

• The second stated codec in the SDP m line is the equivalent to the first BearerCapability element, the BearerCapability element is mapped into the User Service Information (USI) parameter in the sent IAM, the TMR prime is set according the first PSTN XML InformationTransferCapability value

Ensure that the INVITE with encapsulated IAM does not contain the Fallback connection type if the succeeding network does not support the Fallback connection type: • TMR = Speech or audio 3,1 kHz • USI = Speech or audio 3,1 kHz • A TMR prime parameter is not present

A USI prime is not present ISUP Parameter values IAM:

TMR = second InformationTransferCapability TMR prime = first InformationTransferCapability USI = first BearerCapability USI prime = second BearerCapability

SIP Parameter values INVITE: PSTN XML MIME body <?xml version="1.0" encoding="utf-8"?> PSTN BearerCapability BCoctet3 CodingStandard>00< InformationTransferCapability>00000< or InformationTransferCapability>10000< BearerCapability BCoctet3 CodingStandard>00< InformationTransferCapability>10001< SDP: m=audio <proper port number> RTP/AVP CLEARMODE 8 …

Comments SDP: m line contains as the first codec CLEARMODE and as the second codec a G.711 codec Configuration: the succeeding network does not support the Fall back connection type

Message flows SIP NNI MGCF SIP-I INVITE � � INVITE (IAM) 100 Trying �



TSS reference SIP NNI - SIP-I/Basic call/Sending_of_ SIP-INVITE request / Selection criteria PICS 6.2.1/8 Test Purpose name Max-Forwards received, HOP is sent Test Purpose Ensure that on receipt of the Max-Forwards header, the value is mapped into the Hop

counter. The value of the HOP is created from the Max-Forwards header value by applying a given factor




ETSI

ETSI TS 101 572-2 V1.2.1 (2014-07)30


TSS reference SIP NNI - SIP-I/Basic call/Sending_of_ SIP-INVITE request / Selection criteria PICS 6.2.1/5 Test Purpose name Mapping of PSTN XML ProgressIndicator Test Purpose Ensure that on receipt of a PSTN XML attachment in an INVITE request containing a

ProgressIndicator element, this information is mapped into a Progress Indicator IE present in an ISUP Access Transport Parameter the Progress description value is derived from the PSTN XML ProgressDescription element

ISUP Parameter values IAM: ATP Progress Indicator Progress Description=PI_value

SIP Parameter values INVITE: <?xml version="1.0" encoding="utf-8"?> PSTN ProgressIndicator ProgressOctet3 CodingStandard>00< Location>0000< ProgressOctet4 ProgressDescription>PI_value<




Table 6.1.1.1-9: Mapping of PSTN XML ProgressIndicator to ISUP ATP Progress Indicator

PI_value XML ProgressIndicator ProgressDescription

ATP Progress Indicator value

PI_VA_1 '0000001' Call is not end-to-end ISDN; further call progress information may be available in-band

PI_VA_2 '0000010' Destination address is non-ISDN PI_VA_3 '0000011' Origination address is non-ISDN PI_VA_4 '0000100' Call has returned to the ISDN PI_VA_5 '0000101' Interworking has occurred and has resulted in a

telecommunication service change PI_VA_6 '0001000' In-band information or an appropriate pattern is now available

ETSI

ETSI TS 101 572-2 V1.2.1 (2014-07)31

TP number TP_101_035 Reference [1], clause 7.2.1 [2], clause 7.2.3.1.2A.1.1

TSS reference SIP NNI - SIP-I/Basic call/Sending_of_ SIP-INVITE request / Selection criteria PICS 6.2.2/1 Test Purpose name Number Portability Separate Directory Number Addressing Method is used. A Called

Directory Number is present in the sent IAM Test Purpose Ensure that on receipt of an initial INVITE request containing the rn and npdi parameters

in the request line, an INVITE with encapsulated IAM is sent. The Called Party Number is set to: • Nature of address indicator: "Network routing number in national (significant)

number format" or "National (significant) number" or "Network routing number in network specific number format"

• Internal Network Number Indicator: routing to internal network number not allowed • Numbering plan Indicator: ISDN (Telephony) numbering plan (Recommendation

E.164 [i.1]) • Address Signal: derived from the user info of the request URI the country code is

removed. The Called Directory Number is set to: • Nature of address indicator "National (significant) number" • Internal Network Number Indicator: routing to internal network number not allowed • Numbering plan Indicator: ISDN (Telephony) numbering plan (Recommendation

E.164 [i.1]) • Address Signal: derived from the rn parameter if the Number Portability Routing

Number contains an E164 number the country code is removed else the address digits applied unchanged.

ISUP Parameter values IAM: Called party number, Called Directory Number

SIP Parameter values INVITE: Request URI: sip: <called number>; rn=<Number Portability Routing Number>; npdi INVITE (IAM): Request URI: sip: <called number>;

Comments The URI parameters can be received in arbitrary order Message flows SIP NNI MGCF SIP-I



ETSI

ETSI TS 101 572-2 V1.2.1 (2014-07)32


TSS reference SIP NNI - SIP-I/Basic call/Sending_of_ SIP-INVITE request / Selection criteria PICS 6.2.2/2 Test Purpose name Number Portability Concatenated Addressing Method is used. The called party number is

present Test Purpose Ensure that on receipt of an initial INVITE request containing the rn and npdi parameters

in the request line, an INVITE with encapsulated IAM is sent. The Called Party Number is set to: • Nature of address indicator: "Network routing number concatenated with called

directory number" or "National (significant) number" • Internal Network Number Indicator: routing to internal network number not allowed • Numbering plan Indicator: ISDN (Telephony) numbering plan (Recommendation


Number contains an E164 number the country code is removed else the address digits applied unchanged. The called party number derived from the user info is appended except the country code.

ISUP Parameter values IAM: Called party number






TSS reference SIP NNI - SIP-I/Basic call/Sending_of_ SIP-INVITE request / Selection criteria PICS 7.2.2/3 Test Purpose name Number Portability Separate Network Routing Number Addressing Method is used. A

Network Routing Number is present in the sent IAM Test Purpose Ensure that on receipt of an initial INVITE request containing the rn and npdi parameters

in the request line, an INVITE with encapsulated IAM is sent. The Called Party Number is set to: • Nature of address indicator: "National (significant) number" • Internal Network Number Indicator: routing to internal network number not allowed • Numbering plan Indicator: ISDN (Telephony) numbering plan (Recommendation

E.164 [i.1]) • Address Signal: derived from the user info of the request URI the country code is

removed. The Network Routing Number is set to: • Nature of address indicator: "Network routing number in national (significant)

number format" or "Network routing number in network specific number format" • Numbering plan Indicator: ISDN (Telephony) numbering plan (Recommendation


Number contains an E164 number the country code is removed else the address digits applied unchanged.

ISUP Parameter values IAM: Called party number, Network Routing Number





ETSI

ETSI TS 101 572-2 V1.2.1 (2014-07)33

TP number TP_101_038 Reference [1], clause 7.2.1 [2], clause 7.2.3.1.2A.2

TSS reference SIP NNI - SIP-I/Basic call/Sending_of_ SIP-INVITE request / Selection criteria PICS 6.2.2/1 OR PICS 6.2.2/2 OR PICS 6.2.2/3 AND PICS 6.2.2/4 Test Purpose name Sending of Number Portability Forward Information Test Purpose Ensure that on receipt of an initial INVITE request containing the npdi parameters in the

request line, an INVITE with encapsulated IAM is sent. The INVITE with encapsulated IAM contains the Number Portability Forward Information parameter set according the following roles • If the Number Portability Database Dip Indicator is present, and there is no Number

Portability Routing Number, set to "number portability query done for called number, non-ported called subscriber".

ISUP Parameter values IAM: Number Portability Forward Information

SIP Parameter values INVITE: Request URI: sip: <called number>; npdi INVITE (IAM): Request URI: sip: <called number>;





TSS reference SIP NNI - SIP-I/Basic call/Sending_of_ SIP-INVITE request / Selection criteria PICS 6.2.2/1 OR PICS 6.2.2/2 OR PICS 6.2.2/3 AND PICS 6.2.2/4 Test Purpose name Sending of Number Portability Forward Information Test Purpose Ensure that on receipt of an initial INVITE request containing the rn and npdi parameters

in the request line, an INVITE with encapsulated IAM is sent. The INVITE with encapsulated IAM contains the Number Portability Forward Information parameter set according the following roles • If the Number Portability Database Dip Indicator is present, and a Number Portability

Routing Number is present, set to "number portability query done for called number, ported called subscriber".

ISUP Parameter values IAM: Number Portability Forward Information





ETSI

ETSI TS 101 572-2 V1.2.1 (2014-07)34


TSS reference SIP NNI - SIP-I/Basic call/Sending_of_ SIP-INVITE request / Selection criteria PICS 6.2.2/1 OR PICS 6.2.2/2 OR PICS 6.2.2/3 AND PICS 6.2.2/4 Test Purpose name Sending of Number Portability Forward Information Test Purpose Ensure that on receipt of an initial INVITE request containing the rn parameters in the

request line, an INVITE with encapsulated IAM is sent. The INVITE with encapsulated IAM contains the Number Portability Forward Information parameter set according the following roles • If there is no Number Portability Database Dip Indicator, set to "number portability

query not done for called number" ISUP Parameter values IAM:

Number Portability Forward Information SIP Parameter values INVITE:

Request URI: sip: <called number>; rn=<Number Portability Routing Number> INVITE (IAM): Request URI: sip: <called number>;




TP number TP_101_041 Reference [1], clause 7.2.1 [2], clause 7.2.3.1.2B.1

TSS reference SIP NNI - SIP-I/Basic call/Sending_of_ SIP-INVITE request / Selection criteria PICS 6.2.2/5 AND PICS 6.2.2/6 Test Purpose name Request URI cic parameter is mapped into IAM TNS parameter Test Purpose Ensure that on receipt of an initial INVITE request containing the cic parameter in the

request line, an INVITE with encapsulated IAM is sent. The Transit network selection parameter is set to: • Type of network identification: CCITT-standardized identification or national network

identification. • Network identification plan: according value of Type of network identification • Network identification: digits derived from the carrier identification code value of the

cic parameter ISUP Parameter values IAM:

Transit network selection BICC ? SIP Parameter values INVITE:

Request URI: sip: <called number>; cic=< Carrier identification code > INVITE (IAM): Request URI: sip: <called number>;




ETSI

ETSI TS 101 572-2 V1.2.1 (2014-07)35


6.1.1.2 Sending of UPDATE


TSS reference SIP NNI - SIP-I/Basic call/Sending_of_COT/ Selection criteria PICS 6.1.1/1 AND PICS 6.2.1/1 AND NOT PICS 6.2.1/4 Test Purpose name Sending of UPDATE Test Purpose If the INVITE with an encapsulated IAM has already been sent, the UPDATE message

shall be sent, when all of the following conditions have been met: - the requested preconditions (if any) in the IMS network have been met - a possible outstanding continuity check procedure is successfully performed on the

outgoing circuit ISUP Parameter values IAM: Nature of connection indicator = "Continuity check performed on a previous circuit"

or "Continuity check required on this circuit" SIP Parameter values INVITE: Require: precondition



INVITE � � INITE (IAM) 100 Trying � � 100 Trying 183 Session Progress � � 183 Session Progress PRACK � � PRACK 200 OK (PRACK) � � 200 OK (PRACK) UPDATE � � UPDATE 200 OK (UPDATE) � � 200 OK (UPDATE)


ETSI

ETSI TS 101 572-2 V1.2.1 (2014-07)36

TP number TP_102_002 Reference [2], clause 7.3.3.1.3 TSS reference SIP NNI - SIP-I/Basic call/Sending_of_COT/ Selection criteria PICS 6.1.1/2 AND PICS 6.2.1/1 AND NOT PICS 6.2.1/4 Test Purpose name Sending of BICC UPDATE Test Purpose If the INVITE with encapsulate IAM has already been sent, the UPDATE message shall be

sent, when all of the following conditions have been met: - the requested preconditions (if any) in the IMS network have been met

ISUP Parameter values IAM: Nature of connection indicator = "COT to be expected" SIP Parameter values INVITE: Require: precondition





ETSI

ETSI TS 101 572-2 V1.2.1 (2014-07)37

6.1.1.3 Receipt of multiple INVITE request and in-dialog SIP INFO request

TP number TP_103_001 Reference [1], clause 7.2.3 [2] 7.2.3.1.3A.2

TSS reference SIP-ISUP/Basic call/ Receipt of in-dialog SIP INFO requests Selection criteria PICS 6.2.3/1 Test Purpose name Receipt of INFO request Test Purpose If the MGCF supports overlap signalling from the preceding IMS node and the first

incoming SIP INVITE request does not provide a complete number, then the MGCF shall not forward this first SIP INVITE request and additional SIP INFO requests which are used by the MGCF to collect all digits required to identify the called subscriber.

ISUP Parameter values SIP Parameter values INVITE: Supported: 100rel

183 Session Progress: Supported: 100rel or Required: 100rel INFO: Content-Type: application/x-session-info SubsequentDigit: <additional digits>


INVITE � 484 Address Incomplete � ACK � INVITE � 183 Session Progress � INFO � 200 OK (INFO) � INFO � � INVITE (IAM) 200 OK (INFO) � 180 Ringing(3) � � 180 Ringing(ACM)


ETSI

ETSI TS 101 572-2 V1.2.1 (2014-07)38


TSS reference SIP NNI - SIP-I/Basic call/ Receipt of multiple INVITE request Selection criteria PICS 6.2.3/2 Test Purpose name Receipt of multiple INVITE request Test Purpose If the MGCF supports overlap signalling from the preceding IMS node and the first

incoming SIP INVITE request does not provide a complete number, then the MGCF shall not forward this first SIP INVITE request and additional SIP INVITE requests which are used by the MGCF to collect all digits required to identify the called subscriber.


INVITE(1) � CASE A INVITE(2) � 484 Address Incomplete(1) � ACK � INVITE(3) � � INVITE (IAM) 484 Address Incomplete(2) � 180 Ringing(3) � � 180 Ringing(ACM) CASE B 484 Address Incomplete(1) � ACK � INVITE(2) � 484 Address Incomplete(2) � ACK � INVITE(3) � � INVITE (IAM) 180 Ringing(3) � � 180 Ringing (ACM)


6.1.1.4 Sending of 18x provisional responses


TSS reference SIP NNI - SIP-I/Basic call/Sending_of_18x/ Selection criteria Test Purpose name Sending of 180 Ringing after 180 Ringing with a encapsulated ACM was received Test Purpose The SUT shall send the SIP 180 Ringing when receiving the following messages:

- 180 Ringing (ACM) with Called party's status indicator set to subscriber free ISUP Parameter values ACM: BCI Called party status indicator = subscriber free SIP Parameter values Comments Message flows SIP NNI MGCF SIP-I

INVITE � � INVITE (IAM) 100 Trying � � 100 Trying 180 Ringing � � 180 Ringing (ACM)


ETSI

ETSI TS 101 572-2 V1.2.1 (2014-07)39


TSS reference SIP NNI - SIP-I/Basic call/Sending_of_18x/ Selection criteria Test Purpose name Sending of 180 Ringing after CPG was received Test Purpose The SUT shall send the SIP 180 Ringing when receiving the following messages:

- 180 Ringing (CPG) with Event indicator set to ALERTING. ISUP Parameter values ACM: BCI Called party status indicator = no indication

CPG: Event indicator = ALERTING SIP Parameter values Comments Message flows SIP NNI MGCF SIP-I

INVITE � � INVITE (IAM) 100 Trying � � 183 Session Progress (ACM - no indication) 180 Ringing � � 180 Ringing CPG(ALERTING)



TSS reference SIP NNI - SIP-I/Basic call/Sending_of_18x/ Selection criteria PICS 6.2.1/9 Test Purpose name ACM received, P-Earl-Media header present in 180 Test Purpose Ensure that on receipt of a 180 Ringing with an encapsulated ACM subscriber free a 180

Ringing is sent. In the 180 Ringing a P-Early-Media header is present indicating authorization of early media

ISUP Parameter values IAM: 3,1 kHz audio ACM: BCI Called party status indicator = free

SIP Parameter values INVITE: Supported: 100rel P-Early-Media: supported 180 ringing P-Early-Media: < authorization of early media>


INVITE � � INVITE (IAM) 180 Ringing � � 180 Ringing (ACM -free)



TSS reference SIP NNI - SIP-I/Basic call/Sending_of_18x/ Selection criteria PICS 6.2.1/10 Test Purpose name Provide media in a Call-Info header field, or an Alert-Info header field in a 180 Test Purpose Ensure that the SUT is able to provide media instead of the in-band media received from

the PSTN in a Call-Info header field, or an Alert-Info header field present in a 180 Ringing ISUP Parameter values ACM: BCI Called party status indicator = subscriber free SIP Parameter values 180:

Call-Info: <Media resource>; or Alert-Info: <Media resource>


INVITE � � INVITE (IAM) 100 Trying � � 100 Trying 180 Ringing � � 180 Ringing (ACM - free)


ETSI

ETSI TS 101 572-2 V1.2.1 (2014-07)40

TP number TP_104_005 Reference [1], clause 7.2.1 [2], clause 7.2.3.1.4A

TSS reference SIP NNI - SIP-I/Basic call/Sending_of_18x/ Selection criteria PICS 6.2.1/10 Test Purpose name Provide media in a Call-Info header field, or an Alert-Info header field in a 183 Test Purpose Ensure that the SUT is able to provide media instead of the in-band media received from

the PSTN in a Call-Info header field, or an Alert-Info header field present in a 183 Session Progress

ISUP Parameter values ACM: BCI Called party status indicator = no indication SIP Parameter values 183:

Call-Info: <Media resource>; or Alert-Info: <Media resource>


INVITE � � INVITE (IAM) 100 Trying � � 100 Trying 183 Session Progress � � 183 Session Progress ACM(no indication)


ETSI

ETSI TS 101 572-2 V1.2.1 (2014-07)41


TSS reference SIP NNI - SIP-I/Basic call/Sending_of_18x/ Selection criteria PICS 6.2.1/5 Test Purpose name Mapping of Progress Indicator received in a ACM/CPG Test Purpose Ensure that on receipt of an 18x Message with encapsulated ACM called party status

subscriber free or a CPG event indicator ALERTING, a 180 Ringing is sent or 183 Session progress is sent . The Progress Indicator IE contained in the ACM ATP or CPG ATP parameter is mapped into the PSTN XML element in the 180 as indicated in table 6.1.1.4-2. • Progress Indicator received in an ACM called party status subscriber free 180 Ringing

is sent in the PSTN XML element contains the ProgressIndicator value PI_value • Progress Indicator received in an CPG Event indicator ALERTING 180 Ringing is sent

in the PSTN XML element contains the ProgressIndicator value PI_value ISUP Parameter values ACM: CASE A BCi Called party status = subscriber free

CASE B BCi Called party status = no indication oBCi 'inband info available' CPG: ATP contains a Progress Indicator IE

SIP Parameter values 180: <?xml version="1.0" encoding="utf-8"?> PSTN ProgressIndicator ProgressOctet3 CodingStandard>00< Location<yyyy> ProgressOctet4 ProgressDescription>PI_value< 183: <?xml version="1.0" encoding="utf-8"?> PSTN ProgressIndicator ProgressOctet3 CodingStandard>00< Location<yyyy> ProgressOctet4 ProgressDescription>PI_value<g


INVITE � � INVITE (IAM) CASE A 180 Ringing � � 180 Ringing (ACM free) ATP contains a Progress Indicator IE) CASE B 183 Session Progress � � 183 Session Progress(ACM – no

indication) 180 Ringing � � CPG (ATP contains a Progress Indicator

IE) Apply post test routine

ETSI

ETSI TS 101 572-2 V1.2.1 (2014-07)42


TSS reference SIP NNI - SIP-I/Basic call/Sending_of_18x/ Selection criteria PICS 6.2.1/5 Test Purpose name Mapping of High layer compatibility received in a 18x Message with encapsulated

ACM/CPG Test Purpose Ensure that on receipt of an18x Message with encapsulated ACM called party status

subscriber free or a 183 with a CPG event indicator ALERTING, a 180 Ringing is sent. The High layer compatibility IE contained in the ACM ATP or CPG ATP parameter is mapped into the HighLayerCompatibility PSTN XML element in the 180 as indicated in table 6.1.1.4-3. • High layer compatibility received in an ACM called party status subscriber free 180

Ringing is sent in the PSTN XML element contains the HighLayerCompatibility value HLC_value

• High layer compatibility received in an CPG Event indicator ALERTING 180 Ringing is sent in the PSTN XML element contains the HighLayerCompatibility value HLC_value

ISUP Parameter values ACM: CASE A BCi Called party status = subscriber free ATP contains a High layer compatibility IE CASE B BCi Called party status = no indication oBCi 'inband info available' CPG: ATP contains a High layer compatibility IE

SIP Parameter values 180: <?xml version="1.0" encoding="utf-8"?> PSTN HighLayerCompatibility HLOctet3 CodingStandard>00< Interpretation>100< PresentationMethod>01< HLOctet4 HighLayerCharacteristics>HLC_value<


INVITE � � INMVITE (IAM) CASE A 180 Ringing � � 180 Ringing (ACM)

(ATP contains HLC) CASE B 183 Session Progress � � 183 Session Progress

(ACM) 180 Ringing � � 180 Ringing (CPG)

(ATP contains HLC) Apply post test routine

ETSI

ETSI TS 101 572-2 V1.2.1 (2014-07)43


TSS reference SIP NNI - SIP-I/Basic call/Sending_of_18x/ Selection criteria PICS 6.2.1/5 Test Purpose name Mapping of Low layer compatibility received in a 18x with encapsulated ACM/CPG Test Purpose Ensure that on receipt of an 18x Message with an encapsulated ACM called party status

subscriber free or encapsulated CPG event indicator ALERTING, a 180 Ringing is sent. The Low layer compatibility IE contained in the ACM ATP or CPG ATP parameter is mapped into the LowLayerCompatibility PSTN XML element in the 180 as indicated in table 6.1.1.4-4. • Low layer compatibility received in an ACM called party status subscriber free 180

Ringing is sent in the PSTN XML element contains the LowLayerCompatibility value ITC_value

• Low layer compatibility received in an CPG Event indicator ALERTING 180 Ringing is sent in the PSTN XML element contains the LowLayerCompatibility value ITC_value

ISUP Parameter values ACM: CASE A BCi Called party status = subscriber free ATP contains a LLC IE CASE B BCi Called party status = no indication oBCi 'inband info available' CPG: ATP contains a Low layer compatibility IE

SIP Parameter values 180: <?xml version="1.0" encoding="utf-8"?> PSTN LowLayerCompatibility> LLOctet3> CodingStandard>00< InformationTransferCapability>ITC_value< LLOctet4> TransferMode>00< InformationTransferRate>10000<


INVITE � � INVITE (IAM) CASE A 180 Ringing � � 180 Ringing (ACM) (ATP contains LLC) CASE B 183 Session Progress � � 183 Session Progress

(ACM) 180 Ringing � � 180 Ringing CPG

(ATP contains LLC) Apply post test routine

ETSI

ETSI TS 101 572-2 V1.2.1 (2014-07)44


TSS reference SIP NNI - SIP-I/Basic call/Sending_of_18x/ Selection criteria PICS 6.2.1/5 Test Purpose name Mapping of Bearer Capability received in a18x with encapsulated ACM/CPG Test Purpose Ensure that on receipt of an 18x message with encapsulated ACM called party status

subscriber free or a CPG event indicator ALERTING, a 180 Ringing is sent. The Bearer Capability IE contained in the ACM ATP or CPG ATP parameter is mapped into the BearerCapability PSTN XML element in the 180 as indicated in table 6.1.1.4-5. • Bearer Capability received in an ACM called party status subscriber free 180 Ringing

is sent in the PSTN XML element contains the BearerCapability value ITC_value • Bearer Capability received in an CPG Event indicator ALERTING 180 Ringing is sent

in the PSTN XML element contains the BearerCapability value ITC_value ISUP Parameter values ACM: CASE A BCi Called party status = subscriber free

ATP contains a BC IE CASE B BCi Called party status = no indication oBCi 'inband info available' CPG: ATP contains a Bearer Capability IE

SIP Parameter values 180: <?xml version="1.0" encoding="utf-8"?> PSTN BearerCapability BCoctet3 CodingStandard>00< InformationTransferCapability>ITC_value< BCoctet4 TransferMode>00< InformationTransferRate>10000< BCoctet5> Layer1Identification>01< UserInfoLayer1Protocol>00011<


INVITE � � INVITE (IAM) CASE A 180 Ringing � � 180 Ringing (ACM – free) (ACM with ATP contains a

Bearer Capability IE) CASE C 183 Session Progress � � 183 Session Progress

(ACM – no indication) 180 Ringing � � 180 (CPG with ATP contains

a Bearer Capability IE) Apply post test routine

ETSI

ETSI TS 101 572-2 V1.2.1 (2014-07)45


TSS reference SIP NNI - SIP-I/Basic call/Sending_of_18x/ Selection criteria PICS 6.2.1/5 Test Purpose name Mapping of Backward call indicator into PSTN XML ProgressIndicator element value 1 sent

in 180 Test Purpose Ensure that on receipt of a 180 Ringing with encapsulated ACM and the Backward call

indicator ISDN User Part indicator is set to ISDN User Part not used all the way, a 180 Ringing is sent. A PSTN XML ProgressIndicator element is present the value is set to No 1 (Call is not end-to-end ISDN: "further progress information may be available in-band")

ISUP Parameter values ACM: BCI ISDN User Part indicator = ISDN User Part not used all the way SIP Parameter values 180 Ringing

<?xml version="1.0" encoding="utf-8"?> PSTN ProgressIndicator … ProgressOctet4 ProgressDescription>0000001<







indicator ISDN User Part indicator is set to ISDN User Part used all the way and ISDN access indicator = Terminating access non-ISDN, a 180 Ringing is sent. A PSTN XML ProgressIndicator element is present the value is set to No 2 (Destination address is non-ISDN)

ISUP Parameter values ACM: BCI ISDN User Part indicator = ISDN User Part used all the way ISDN access indicator = Terminating access non-ISDN

SIP Parameter values 180 Ringing <?xml version="1.0" encoding="utf-8"?> PSTN ProgressIndicator … ProgressOctet4 ProgressDescription>0000010<




ETSI

ETSI TS 101 572-2 V1.2.1 (2014-07)46




indicator ISDN User Part indicator is set to ISDN User Part used all the way and ISDN access indicator = Terminating access ISDN, a 180 Ringing is sent. A PSTN XML ProgressIndicator element is present the value is set to No 7

ISUP Parameter values ACM: BCI ISDN User Part indicator = ISDN User Part used all the way ISDN access indicator = Terminating access ISDN



INVITE � � IAM 100 Trying � � 100 Trying 180 Ringing � � 180 Ringing (ACM)



TSS reference SIP NNI - SIP-I/Basic call/Sending_of_18x/ Selection criteria PICS 6.2.1/5 Test Purpose name Mapping of optional Backward call indicator into PSTN XML ProgressIndicator element

value 8 sent in 180 Test Purpose Ensure that on receipt of a 180 Ringing with ACM and the optional Backward call indicator

In-band information indicator in-band information or an appropriate pattern is now available, a 180 Ringing is sent. A PSTN XML ProgressIndicator element is present the value is set to No 8

ISUP Parameter values ACM: oBCI In-band information indicator in-band information or an appropriate pattern is now available





ETSI

ETSI TS 101 572-2 V1.2.1 (2014-07)47


TSS reference SIP NNI - SIP-I/Basic call/Sending_of_18x/ Selection criteria PICS 6.2.1/5 AND PICS 6.2.4/1 AND PICS 6.2.4/8 Test Purpose name The SUT performs Fall back Test Purpose Ensure that on receipt of an INVITE request and the subsequent ISUP/BICC network is not

able to perform Fall back, Fall back is performed in the SUT: The TMR in the sent INVITE (IAM) is set to 'speech' or '3,1 kHz audio' USI is copied from the first BearerCapability element received in the PSTN XML. Upon an ACM is received a 180 Ringing is sent

ISUP Parameter values SIP Parameter values INVITE: PSTN XML MIME body

<?xml version="1.0" encoding="utf-8"?> PSTN BearerCapability BCoctet3 CodingStandard>00< InformationTransferCapability>00000< or InformationTransferCapability>10000< …. BearerCapability BCoctet3 CodingStandard>00< InformationTransferCapability>10001< …. 180 Ringing <?xml version="1.0" encoding="utf-8"?> PSTN ProgressIndicator … ProgressOctet4 ProgressDescription>0000101< BearerCapability BCoctet3 CodingStandard>00< InformationTransferCapability>00000< or InformationTransferCapability>10000< ….

Comments Fallback is performed in the SUT Message flows SIP NNI MGCF SIP-I



ETSI

ETSI TS 101 572-2 V1.2.1 (2014-07)48


TSS reference SIP NNI - SIP-I/Basic call/Sending_of_18x/ Selection criteria PICS 6.2.1/5 AND PICS 6.2.4/1 AND PICS 6.2.4/8 Test Purpose name Receipt of TMU speech, no BC present in ATP Test Purpose Ensure that on receipt of a Transmission medium used parameter set to speech in the 180

Ringing with an ACM, a 180 Ringing is sent and a PSTN XML BearerCapability element is present the InformationTransferCapability is set to Speech

ISUP Parameter values ACM: Transmission medium used = speech SIP Parameter values 180 Ringing

<?xml version="1.0" encoding="utf-8"?> PSTN BearerCapability BCoctet3 CodingStandard>00< InformationTransferCapability>00000< …





TSS reference SIP NNI - SIP-I/Basic call/Sending_of_18x/ Selection criteria PICS 6.2.1/5 AND PICS 6.2.4/1 AND PICS 6.2.4/8 Test Purpose name Receipt of TMU 3,1 kHz audio, no BC present in ATP Test Purpose Ensure that on receipt of a Transmission medium used parameter set to 3,1 kHz audio in

the 180 Ringing with encapsulated ACM, a 180 Ringing is sent and a PSTN XML BearerCapability element is present the InformationTransferCapability is set to 3,1 kHz audio

ISUP Parameter values ACM: Transmission medium used = 3,1 kHz audio SIP Parameter values 180 Ringing

<?xml version="1.0" encoding="utf-8"?> PSTN BearerCapability BCoctet3 CodingStandard>00< InformationTransferCapability>10000< …




ETSI

ETSI TS 101 572-2 V1.2.1 (2014-07)49


TSS reference SIP NNI - SIP-I/Basic call/Sending_of_18x/ Selection criteria PICS 6.2.1/5 AND PICS 6.2.4/1 AND PICS 6.2.4/8 Test Purpose name Receipt of TMU, BC present in ATP PSTN XML BearerCapability sent in 180 Test Purpose Ensure that on receipt of a Transmission medium used parameter and in the ATP a Bearer

Capability IE in the 180 Ringing with encapsulated ACM, a 180 Ringing is sent and a PSTN XML BearerCapability element is present the InformationTransferCapability is set as indicated in table 6.1.1.4-1

ISUP Parameter values ACM: Transmission medium used, ATP Bearer Capability IE SIP Parameter values 180 Ringing

<?xml version="1.0" encoding="utf-8"?> PSTN BearerCapability BCoctet3 CodingStandard>00< InformationTransferCapability>ITC_value< …





TSS reference SIP NNI - SIP-I/Basic call/Sending_of_18x/ Selection criteria PICS 6.2.1/5 AND PICS 6.2.4/1 AND PICS 6.2.4/8 Test Purpose name Receipt of TMU, BC present in ATP PSTN XML BearerCapability sent in 183 Test Purpose Ensure that on receipt of a Transmission medium used parameter and in the ATP a Bearer

Capability IE in the 180 Ringing with encapsulated ACM, a 183 Session Progress is sent and a PSTN XML BearerCapability element is present the InformationTransferCapability is set as indicated in table 6.1.1.4-1

ISUP Parameter values ACM: Transmission medium used, ATP Bearer Capability IE BCi Called party status = no indication

SIP Parameter values 183 Session Progress <?xml version="1.0" encoding="utf-8"?> PSTN BearerCapability BCoctet3 CodingStandard>00< InformationTransferCapability>ITC_value< …


INVITE � � INVITE (IAM) 100 Trying � � 100 Trying 183 Session Progress � � 183 Session Progress


Table 6.1.1.4-1: Mapping of TMU and Bearer capability IE to PSTN XML BearerCapability

ITC_value ← 180 Ringing or 183 Session Progress ←ACM/CPG ITC_value_VA_01 PSTN XML BearerCapability = "Speech" TMU "Speech"

ATP BC "speech" ITC_value_VA_02 PSTN XML BearerCapability = "Speech" TMU "3,1 kHz audio"

ATP BC "speech" ITC_value_VA_03 PSTN XML BearerCapability = "3,1 kHz audio" TMU "Speech "

ATP BC "3,1 kHz audio" ITC_value_VA_04 PSTN XML BearerCapability = "3,1 kHz audio" TMU "3,1 kHz audio"

ATP BC "3,1 kHz audio"

ETSI

ETSI TS 101 572-2 V1.2.1 (2014-07)50


TSS reference SIP NNI - SIP-I/Basic call/Sending_of_18x/ Selection criteria NOT PICS 6.2.1/5 AND NOT PICS 6.2.1/9 Test Purpose name ACM no indication received, no SIP response is sent Test Purpose Ensure that on receipt of an early 183 Session Progress with encapsulated ACM no SIP

response is sent if the INVITE does not contain a P-Early-Media header ISUP Parameter values IAM: 3,1 kHz audio

ACM: BCI Called party status indicator = no indication SIP Parameter values Comments Message flows SIP NNI MGCF SIP-I

INVITE � � INVITE(IAM) � 183 Session Progress(ACM(no indication))



TSS reference SIP NNI - SIP-I/Basic call/Sending_of_18x/ Selection criteria PICS 6.2.1/9 Test Purpose name ACM received, P-Earl-Media header present in 183 Test Purpose Ensure that on receipt 183 Session Progress with an encapsulated early ACM a 183

Session Progress is sent. In the 183 session Progress a P-Early-Media header is present indicating authorization of early media

ISUP Parameter values IAM: 3,1 kHz audio ACM: BCI Called party status indicator = no indication

SIP Parameter values INVITE: Supported: 100rel P-Early-Media: supported 183 Session Progress P-Early-Media: < authorization of early media>


INVITE � � INVITE (IAM) 183 Session Progress � � 183 Session Progress ACM

(no indication) Apply post test routine

ETSI

ETSI TS 101 572-2 V1.2.1 (2014-07)51

TP number TP_104_021 Reference [1], clause 7.2.1 [2], clauses 7.2.3.1.4A, table, 7.2.3.1.4A.1

TSS reference SIP NNI - SIP-I/Basic call/Sending_of_18x/ Selection criteria PICS 6.2.1/9 Test Purpose name CPG received, P-Earl-Media header present in 183 Test Purpose Ensure that on receipt of CPG containing an optional backward call indicator set to In-band

info or an appropriate pattern is now available a 183 Session Progress is sent. In the 183 session Progress a P-Early-Media header is present indicating authorization of early media

ISUP Parameter values IAM: 3,1 kHz audio CPG: oBCi In-band info or an appropriate pattern is now available

SIP Parameter values INVITE: Supported: 100rel P-Early-Media: supported 183 Session Progress P-Early-Media: < authorization of early media>


INVITE � � INVITE (IAM) 183 Session Progress � � 183 Session Progress

(ACM) 183 Session Progress � � 183 Session Progress

(CPG) Apply post test routine


TSS reference SIP NNI - SIP-I/Basic call/Sending_of_18x/ Selection criteria PICS 6.2.1/5 Test Purpose name Mapping of optional Backward call indicator in encapsulated ACM into PSTN XML

ProgressIndicator element value 8 sent in a 183 Test Purpose Ensure that on receipt of a 183 Session Progress with encapsulated ACM and the optional

Backward call indicator In-band information indicator in-band information or an appropriate pattern is now available, a 183 Session Progress is sent. A PSTN XML ProgressIndicator element is present the value is set to No 8

ISUP Parameter values ACM: BCi ISDN access indicator = Terminating access ISDN BCi Called party status indicator = no indication oBCI In-band information indicator in-band information or an appropriate pattern is now available

SIP Parameter values 183 Session Progress <?xml version="1.0" encoding="utf-8"?> PSTN ProgressIndicator … ProgressOctet4 ProgressDescription>0001000<




ETSI

ETSI TS 101 572-2 V1.2.1 (2014-07)52


TSS reference SIP NNI - SIP-I/Basic call/Sending_of_18x/ Selection criteria PICS 6.2.1/5 Test Purpose name Mapping of Backward call indicator in encapsulated ACM into PSTN XML

ProgressIndicator element value 1 sent in a 183 Test Purpose Ensure that on receipt of a 183 Session Progress with encapsulated ACM and the

Backward call indicator ISDN User Part indicator is set to ISDN User Part not used all the way, a 183 Session Progress is sent. A PSTN XML ProgressIndicator element is present the value is set to No 1 (Call is not end-to-end ISDN: "further progress information may be available in-band")

ISUP Parameter values ACM: BCI ISDN User Part indicator = ISDN User Part not used all the way BCi Called party status indicator = no indication






TSS reference SIP NNI - SIP-I/Basic call/Sending_of_18x/ Selection criteria PICS 6.2.1/5 Test Purpose name Mapping of Backward call indicator in encapsulated ACM into PSTN XML


Backward call indicator ISDN User Part indicator is set to ISDN User Part used all the way and ISDN access indicator = Terminating access non-ISDN, a 183 Session Progress is sent. A PSTN XML ProgressIndicator element is present the value is set to No 2 (Destination address is non-ISDN)

ISUP Parameter values ACM: BCI ISDN User Part indicator = ISDN User Part used all the way BCi ISDN access indicator = Terminating access non-ISDN BCi Called party status indicator = no indication



INVITE � � INVITE (IAM) 100 Trying � 183 Session Progress � � 183 Session Progress


ETSI

ETSI TS 101 572-2 V1.2.1 (2014-07)53


TSS reference SIP NNI - SIP-I/Basic call/Sending_of_18x/ Selection criteria PICS 6.2.1/5 Test Purpose name Mapping of Backward call indicator into in encapsulated ACM PSTN XML


Backward call indicator ISDN User Part indicator is set to ISDN User Part used all the way and ISDN access indicator = Terminating access ISDN, a 183 Session Progress is sent. A PSTN XML ProgressIndicator element is present the value is set to No 7

ISUP Parameter values ACM: BCI ISDN User Part indicator = ISDN User Part used all the way BCi ISDN access indicator = Terminating access ISDN BCi Called party status indicator = no indication



INVITE � � INVITE (IAM) 100 Trying � 183 Session Progress � � 183 Session Progress



TSS reference SIP NNI - SIP-I/Basic call/Sending_of_18x/ Selection criteria PICS 6.2.1/5 Test Purpose name Mapping of optional Backward call indicator in encapsulated CPG into PSTN XML

ProgressIndicator element value 8 sent in a 183 Test Purpose Ensure that on receipt of a 183 Session Progress with encapsulated CPG and the optional

Backward call indicator In-band information indicator in-band information or an appropriate pattern is now available, a 183 Session Progress is sent. A PSTN XML ProgressIndicator element is present the value is set to No 8

ISUP Parameter values CPG: Event indicator = Progress oBCI In-band information indicator in-band information or an appropriate pattern is now available



INVITE � � INVITE (IAM) � 183 Session Progress

(ACM no indication) 183 Session Progress � � 183 Session Progress


ETSI

ETSI TS 101 572-2 V1.2.1 (2014-07)54


TSS reference SIP NNI - SIP-I/Basic call/Sending_of_18x/ Selection criteria PICS 6.2.1/5 Test Purpose name Mapping of Backward call indicator in encapsulated CPG into PSTN XML

ProgressIndicator element value 1 sent in a 183 Test Purpose Ensure that on receipt of 183 Session Progress with an encapsulated a CPG and the

Backward call indicator ISDN User Part indicator is set to ISDN User Part not used all the way, a 183 Session Progress is sent. A PSTN XML ProgressIndicator element is present the value is set to No 1 (Call is not end-to-end ISDN: "further progress information may be available in-band")

ISUP Parameter values CPG: Event indicator = Progress BCI ISDN User Part indicator = ISDN User Part not used all the way



INVITE � � INVITE(IAM) � 183 Session Progress





ProgressIndicator element value 2 sent in a 183 Test Purpose Ensure that on receipt of a 183 Session Progress with encapsulated CPG and the

Backward call indicator ISDN User Part indicator is set to ISDN User Part used all the way and ISDN access indicator = Terminating access non-ISDN, a 183 Session Progress is sent. A PSTN XML ProgressIndicator element is present the value is set to No 2 (Destination address is non-ISDN)

ISUP Parameter values CPG: Event indicator = Progress or in-band information or an appropriate pattern is now available BCI ISDN User Part indicator = ISDN User Part used all the way BCi ISDN access indicator = Terminating access non-ISDN






ETSI

ETSI TS 101 572-2 V1.2.1 (2014-07)55



ProgressIndicator element value 7 sent in a 183 Test Purpose Ensure that on receipt of a 183 Session Progress with encapsulated CPG and the

Backward call indicator ISDN User Part indicator is set to ISDN User Part used all the way and ISDN access indicator = Terminating access ISDN, a 183 Session Progress is sent. A PSTN XML ProgressIndicator element is present the value is set to No 7

ISUP Parameter values CPG: Event indicator = Progress or in-band information or an appropriate pattern is now available BCI ISDN User Part indicator = ISDN User Part used all the way BCi ISDN access indicator = Terminating access ISDN



INVITE � � (INVITE) IAM � 183 Session Progress



ETSI

ETSI TS 101 572-2 V1.2.1 (2014-07)56

TP number TP_104_033 Reference [1], clause 7.2.1 [2], clause 7.2.3.1.4, table 7a.0f

TSS reference SIP NNI - SIP-I/Basic call/Sending_of_18x/ Selection criteria PICS 6.2.1/5 Test Purpose name Mapping of Progress Indicator received in a ACM/CPG into 183 Test Purpose Ensure that on receipt of a 183 Message with encapsulated ACM called party status no

indication or CPGevent indicator in-band information or an appropriate pattern is now available containing a ATP Progress Indicator, a 183 Session Progress is sent. The Progress Indicator IE contained in the ACM or CPG ATP parameter is mapped into the PSTN XML element in the 183 Session Progress as indicated in table 6.1.1.4-2. • Progress Indicator received in an ACM called party status user no indication a 183

Session Progress is sent in the PSTN XML element contains the ProgressIndicator value PI_value

• Progress Indicator received in an CPG 183 Session Progress is sent in the PSTN XML element contains the ProgressIndicator value PI_value

ISUP Parameter values ACM: CASE A BCi Called party status = no indication ATP contains a Progress Indicator IE CASE B BCi Called party status = no indication oBCi 'inband info available' CPG: ATP contains a Progress Indicator IE

SIP Parameter values 183 Session Progress: <?xml version="1.0" encoding="utf-8"?> PSTN ProgressIndicator ProgressOctet3 CodingStandard>00< Location>yyyy< ProgressOctet4 ProgressDescription>PI_value<

Comments Message flows SIP NII MGCF SIP-I

INVITE � � INVITE (IAM) CASE A 183 Session Progress � � 183 Session Progress

(ACM no indication) ATP contains a Progress Indicator IE

CASE B � 183 Session Progress

(ACM – no indication) 183 Session Progress � � 183 Session Progress

(CPG – PROGRESS) ATP contains a Progress Indicator IE


Table 6.1.1.4-2: Mapping of Progress Indicator information element to PSTN XML ProgressIndicator

PI_value ATP Progress Indicator value XML ProgressIndicator ProgressDescription

PI_VA_1 Call is not end-to-end ISDN; further call progress information may be available in-band

'0000001'

PI_VA_2 Destination address is non-ISDN '0000010' PI_VA_3 Origination address is non-ISDN '0000011' PI_VA_4 Call has returned to the ISDN '0000100' PI_VA_5 Interworking has occurred and has resulted in a

telecommunication service change '0000101'

PI_VA_6 In-band information or an appropriate pattern is now available '0001000'

ETSI

ETSI TS 101 572-2 V1.2.1 (2014-07)57


TSS reference SIP NNI - SIP-I/Basic call/Sending_of_18x/ Selection criteria PICS 6.2.1/5 Test Purpose name Mapping of High layer compatibility received in a ACM/CPG into 183 Test Purpose Ensure that on receipt of a 183 Session Progress with encapsulated ACM called party

status no indication or CPG event indicator in-band information or an appropriate pattern is now available, a 183 Session Progress is sent. The High layer compatibility IE contained in the ACM ATP parameter is mapped into the HighLayerCompatibility PSTN XML element in the 183 Session Progress as indicated in table 6.1.1.4-3. • High layer compatibility received in an ACM called party status no indication, a 183

Session Progress is sent in the PSTN XML element contains the HighLayerCompatibility value HLC_value

• High layer compatibility received in an CPG Event indicator in-band information or an appropriate pattern is now available 183 Session Progress is sent in the PSTN XML element contains the HighLayerCompatibility value HLC_value

ISUP Parameter values ACM: CASE A BCi Called party status = no indication CASE B BCi Called party status = no indication oBCi 'inband info available' CPG: ATP contains a High layer compatibility IE

SIP Parameter values 183 Session Progress: <?xml version="1.0" encoding="utf-8"?> PSTN HighLayerCompatibility HLOctet3 CodingStandard>00< Interpretation>100< PresentationMethod>01< HLOctet4 HighLayerCharacteristics>HLC_value<



(ACM) CASE B � 183 Session Progress

(ACM – no indication)) 183 Session Progress � � 183 Session Progress

(CPG - ATP contains a High layer compatibility IE )


Table 6.1.1.4-3: Mapping of High layer compatibility information element to PSTN XML HighLayerCharacteristic

HLC_value DSS1 High layer characteristics identification XML HighLayerCharacteristic HLC_VA_1 Telephony '0000001' HLC_VA_2 Facsimile Group 2/3 '0000100' HLC_VA_3 Facsimile Group 4 Class I '0100001' HLC_VA_4 Facsimile service Group 4, Classes II and III '0100100' HLC_VA_5 Syntax based Videotex '0110010' HLC_VA_6 International Videotex interworking via gateways or

interworking units '0110011'

HLC_VA_7 Telex service '0110101' HLC_VA_8 FTAM application '1000010' HLC_VA_9 Videotelephony '1100000'

ETSI

ETSI TS 101 572-2 V1.2.1 (2014-07)58


TSS reference SIP NNI - SIP-I/Basic call/Sending_of_18x/ Selection criteria PICS 6.2.1/5 Test Purpose name Mapping of Low layer compatibility received in a 183 Session Progress with encapsulated

ACM/CPG into 183 Session Progress Test Purpose Ensure that on receipt of a 183 Session Progress with encapsulated ACM called party

status no indication or CPG event indicator in-band information or an appropriate pattern is now available, a 183 Session Progress is sent. The Low layer compatibility IE contained in the ACM ATP parameter is mapped into the LowLayerCompatibility PSTN XML element in the 183 Session Progress as indicated in table 6.1.1.4-4. • Low layer compatibility received in an ACM called party status no indication, a 183

Session Progress is sent in the PSTN XML element contains the LowLayerCompatibility value ITC_value

• Low layer compatibility received in an CPG Event indicator in-band information or an appropriate pattern is now available 183 Session Progress is sent in the PSTN XML element contains the LowLayerCompatibility value ITC_value

ISUP Parameter values ACM: CASE A BCi Called party status = no indication CASE B BCi Called party status = no indication oBCi 'inband info available' CPG: ATP contains a Low layer compatibility IE

SIP Parameter values 183 Session Progress: <?xml version="1.0" encoding="utf-8"?> PSTN LowLayerCompatibility> LLOctet3> CodingStandard>00< InformationTransferCapability>ITC_value< LLOctet4> TransferMode>00< InformationTransferRate>10000<





(CPG –Alerting ) Apply post test routine

Table 6.1.1.4-4: Mapping of Low Layer Compatibility to PSTN XML LowLayerCompatibility

ITC_value LLC Information transfer capability XML LLC InformationTransferCapability ITC_VA_1 Speech '00000' ITC_VA_2 3,1 kHz audio '10000' ITC_VA_3 Unrestricted digital info '01001' ITC_VA_3 7 kHz audio '10001'

ETSI

ETSI TS 101 572-2 V1.2.1 (2014-07)59


TSS reference SIP NNI - SIP-I/Basic call/Sending_of_18x/ Selection criteria PICS 6.2.1/5 Test Purpose name Mapping of Bearer Capability received in a 183 Session Progress with encapsulated

ACM/CPG Test Purpose Ensure that on receipt of an ACM called party status no indication or CPG event indicator

in-band information or an appropriate pattern is now available, a 183 Session Progress is sent. The Bearer Capability IE contained in the ACM ATP parameter is mapped into the BearerCapability PSTN XML element in the 183 Session Progress as indicated in table 6.1.1.4-5. • Bearer Capability received in an ACM called party status subscriber free 183 Session

Progress is sent in the PSTN XML element contains the BearerCapability value ITC_value

• Bearer Capability received in an CPG Event indicator in-band information or an appropriate pattern is now available 183 Session Progress is sent in the PSTN XML element contains the BearerCapability value ITC_value

ISUP Parameter values ACM: CASE A BCi Called party status = no indication CASE B BCi Called party status = no indication oBCi 'inband info available' CPG: ATP contains a Bearer Capability IE

SIP Parameter values 183 Session Progress: <?xml version="1.0" encoding="utf-8"?> PSTN BearerCapability BCoctet3 CodingStandard>00< InformationTransferCapability>ITC_value< BCoctet4 TransferMode>00< InformationTransferRate>10000< BCoctet5> Layer1Identification>01< UserInfoLayer1Protocol>00011<






Table 6.1.1.4-5: Mapping of Bearer capability to PSTN XML BearerCapability

ITC_value BC Information transfer capability XML InformationTransferCapability ITC_VA_1 Speech '00000' ITC_VA_2 3,1 kHz audio '10000' ITC_VA_3 Unrestricted digital inf. W/tone/ann '10001' ITC_VA_4 Unrestricted digital information '01000'

ETSI

ETSI TS 101 572-2 V1.2.1 (2014-07)60

TP number TP_104_037 Reference [1], clause 7.2.1 [2], clause 7.2.3.1.4B

TSS reference SIP NNI - SIP-I/Basic call/Sending_of_18x/ Selection criteria Test Purpose name ACM containing CDIV information, a 181 is sent Test Purpose Ensure that on receipt of a 181 Call Is Being Forwarded with encapsulated ACM containing

a Redirection number, Call diversion information and Generic notification set to 'Call is diverted', a 181 Call Is Being Forwarded is sent

ISUP Parameter values ACM: BCi Called party status = no indication Redirection number Call diversion information Generic notification = 'Call is diverted'

SIP Parameter values 181 Call Is Being Forwarded Comments Message flows SIP NNI MGCF SIP-I

INVITE � � INVITE (IAM) 100 Trying � 181 Call Is Being Forwarded � � 183 Session Progress


TP number TP_104_038 Reference [1], clauses 7.2.1, 7.2.3.1.4B TSS reference SIP NNI - SIP-I/Basic call/Sending_of_18x/ Selection criteria PICS 6.2.1/9 AND PICS 6.3.2/5 Test Purpose name ACM containing CDIV information and oBCi inband info available, a 181 Call Is Being

Forwarded is sent a P-Early-Media present Test Purpose Ensure that on receipt of a 181 Call Is Being Forwarded with encapsulated ACM containing

a Redirection number, Call diversion information and Generic notification set to 'Call is diverted' and an optional backward call indicator set to In-band info or an appropriate pattern is now available, a 181 Call Is Being Forwarded is sent, a P-Early-Media is present indicating authorization of early media

ISUP Parameter values ACM: BCi Called party status = no indication Redirection number Call diversion information Generic notification = 'Call is diverted'

SIP Parameter values 181 Call Is Being Forwarded P-Early-Media: <indicating authorization of early media>


INVITE � � INVITE (IAM) 100 Trying � 181 Call Is Being Forwarded � � 183 Session Progress


ETSI

ETSI TS 101 572-2 V1.2.1 (2014-07)61


TSS reference SIP NNI - SIP-I/Basic call/Sending_of_18x/ Selection criteria PICS 6.3.2/5 Test Purpose name CPG containing CDIV information, a 181 is sent Test Purpose Ensure that on receipt of a 181 Call Is Being Forwarded with encapsulated CPG Event

Indicator set to Progress containing a Redirection number, Call diversion information and Generic notification set to 'Call is diverted', a 181 Call Is Being Forwarded is sent

ISUP Parameter values CPG: Event Indicator set to Progress Redirection number Call diversion information Generic notification = 'Call is diverted' oBCI In-band information indicator in-band information or an appropriate pattern is now available

SIP Parameter values 181 Call Is Being Forwarded Comments Message flows SIP NNI MGCF SIP-I

INVITE � � INVITE (IAM) 180/183 � � 180/183 (ACM) 181 Call Is Being Forwarded � � 183 Session Progress



TSS reference SIP NNI - SIP-I/Basic call/Sending_of_18x/ Selection criteria PICS 6.2.1/9 AND PICS 6.3.2/5 Test Purpose name ACM containing CDIV information and oBCi inband info available, a 181 is sent a

P-Early-Media present Test Purpose Ensure that on receipt of a 181 Call Is Being Forwarded with encapsulated CPG Event

Indicator set to Progress containing a Redirection number, Call diversion information and Generic notification set to 'Call is diverted' and an optional backward call indicator set to In-band info or an appropriate pattern is now available, a 181 Call Is Being Forwarded is sent, a P-Early-Media is present indicating authorization of early media

ISUP Parameter values CPG: Event Indicator set to Progress Redirection number Call diversion information Generic notification = 'Call is diverted'

SIP Parameter values INVITE: Supported: 100rel P-Early-Media: < authorization of early media> 181 Call Is Being Forwarded P-Early-Media: <indicating authorization of early media>


INVITE � � INVITE (IAM) 180/183 � � 180/183 (ACM) 181 Call Is Being Forwarded � � 183 Session Progress


ETSI

ETSI TS 101 572-2 V1.2.1 (2014-07)62

6.1.1.5 Sending of the 200 OK (INVITE)


TSS reference SIP NNI - SIP-I/Basic call/Sending_of_200_OK/ Selection criteria Test Purpose name A 200 OK with encapsulated ANM is received a 200 OK is sent Test Purpose Ensure that on receipt of a 200 OK (ANM) the SUT sends a 200 OK INVITE ISUP Parameter values SIP Parameter values Comments Message flows SIP NNI MGCF SIP-I

INVITE � � INVITE (IAM) 100 Trying � � 100 Trying 180 Ringing � � 180 Ringing (ACM) 200 OK (INVITE) � � 200 OK (INVITE) (ANM) ACK � � ACK



TSS reference SIP NNI - SIP-I/Basic call/Sending_of_200_OK/ Selection criteria Test Purpose name A 200 OK with encapsulated CON is received a 200 OK is sent Test Purpose Ensure that on receipt of a 200 OK (CON) the SUT sends a 200 OK (INVITE) ISUP Parameter values SIP Parameter values Comments Message flows SIP NNI MGCF SIP-I

INVITE � � INVITE (IAM) 100 Trying � � 100 Trying 200 OK (INVITE) � � 200 OK (INVITE) (CON) ACK � � ACK


ETSI

ETSI TS 101 572-2 V1.2.1 (2014-07)63

TP number TP_105_003 Reference [1], clause 7.2.1 [2], clauses 7.2.3.1.5, table, 7.2.3.1.5.1

TSS reference SIP NNI - SIP-I/Basic call/Sending_of_200_OK/ Selection criteria PICS 6.2.1/5 Test Purpose name Progress indicator received in 200 OK (ANM) with encapsulated ANM/CON is mapped into

PSTN XML ProgressIndicator Test Purpose Ensure that on receipt of a 200 OK (INVITE) with encapsulated ANM/CON and an ATP

containing a Progress indicator IE set to value PI_value a, 200 OK (INVITE) is sent. the PSTN XML ProgressIndicator value is set as indicated in table 6.1.1.5-1

ISUP Parameter values ANM/CON: ATP contains a Progress Indicator IE value PI_value SIP Parameter values 200 OK INVITE:

<?xml version="1.0" encoding="utf-8"?> PSTN ProgressIndicator ProgressOctet3 CodingStandard>00< Location<yyyy> ProgressOctet4 ProgressDescription>PI_value<


INVITE � � INVITE (IAM) CASE A 180 Ringing � � 180 Ringing (ACM - free) 200 OK (INVITE) � � 200 OK (INVITE) (ANM) ACK � � ACK CASE B 200 OK (INVITE) � � 200 OK (INVITE) CON ACK � � ACK





'0000001'




ETSI

ETSI TS 101 572-2 V1.2.1 (2014-07)64


TSS reference SIP NNI - SIP-I/Basic call/Sending_of_200_OK/ Selection criteria PICS 6.2.1/5 Test Purpose name High layer compatibility received in 200 OK (INVITE)with encapsulated ANM/CON is

mapped into PSTN XML HighLayerCompatibility Test Purpose Ensure that on receipt of a 200 OK (INVITE) with encapsulated ANM/CON and an ATP

containing a High layer compatibility IE set to value HLC_value, a 200 OK INVITE is sent. the PSTN XML HighLayerCompatibility value is set as indicated in table 6.1.1.5-2

ISUP Parameter values ANM/CON: ATP contains a High layer compatibility IE value HLC_value SIP Parameter values 200 OK INVITE:

<?xml version="1.0" encoding="utf-8"?> PSTN HighLayerCompatibility HLOctet3 CodingStandard>00< Interpretation>100< PresentationMethod>01< HLOctet4 HighLayerCharacteristics>HLC_value<


INVITE � � INVITE (IAM) CASE A 180 Ringing � � 180 Ringing (ACM) 200 OK (INVITE) � � 200 OK (INVITE) (ANM) ACK � � ACK CASE B 200 OK (INVITE) � � 200 OK (INVITE) CON ACK � � ACK






ETSI

ETSI TS 101 572-2 V1.2.1 (2014-07)65


TSS reference SIP NNI - SIP-I/Basic call/Sending_of_200_OK/ Selection criteria PICS 6.2.1/5 Test Purpose name Low layer compatibility received in 200 OK (ANM) with encapsulated ANM/CON is mapped

into PSTN XML LowLayerCompatibility Test Purpose Ensure that on receipt of a 200 OK (INVITE) with encapsulated ANM/CON and an ATP

containing a Low layer compatibility IE set to value ITC_value, a 200 OK INVITE is sent. the PSTN XML LowLayerCompatibility value is set as indicated in table 6.1.1.5-3

ISUP Parameter values ANM/CON: ATP contains a Low layer compatibility IE value ITC_value SIP Parameter values 200 OK INVITE:

<?xml version="1.0" encoding="utf-8"?> PSTN LowLayerCompatibility> LLOctet3> CodingStandard>00< InformationTransferCapability>ITC_value< LLOctet4> TransferMode>00< InformationTransferRate>10000< LLOctet5> Layer1Identification>01</ UserInfoLayer1Protocol>ITC_value</

Comments When the 'XML UserInfoLayer1Protocol' element is absent, the entire 'LLOctet5' element is absent

ACKMessage flows SIP NNI MGCF SIP-I INVITE � � INVITE (IAM) CASE A 180 Ringing � � 180 Ringing (ACM free) 200 OK (INVITE) � � 200 OK (INVITE) ANM ACK � � ACK CASE B 200 OK (INVITE) � � 200 OK (INVITE) (CON) ACK � � ACK



ITC_value LLC Information transfer capability

XML LLC InformationTransferCapability

XML UserInfoLayer1Protocol

ITC_VA_1 Speech '00000' '00011' ITC_VA_2 3,1 kHz audio '10000' '00011' ITC_VA_3 Unrestricted digital info '01000' absent ITC_VA_4 7 kHz audio '10001' '00110'

ETSI

ETSI TS 101 572-2 V1.2.1 (2014-07)66


TSS reference SIP NNI - SIP-I/Basic call/Sending_of_200_OK/ Selection criteria PICS 6.2.1/5 Test Purpose name Bearer Capability received in 200 OK (INVITE) with encapsulated ANM/CON is mapped

into PSTN XML BearerCapability Test Purpose Ensure that on receipt of a 200 OK (INVITE) with encapsulated ANM/CON and an ATP

containing a Bearer Capability IE set to value ITC_value, a 200 OK INVITE is sent. the PSTN XML BearerCapability value is set as indicated in table 6.1.1.5-4

ISUP Parameter values ANM/CON: ATP contains a Bearer Capability IE value ITC_value SIP Parameter values 200 OK INVITE:

<?xml version="1.0" encoding="utf-8"?> PSTN BearerCapability BCoctet3 CodingStandard>00< InformationTransferCapability>ITC_value< BCoctet4 TransferMode>00< InformationTransferRate>10000< BCoctet5> Layer1Identification>01< UserInfoLayer1Protocol>ITC_value<


INVITE � � INVITE (IAM) CASE A 180 Ringing � � 180 Ringing (ACM- free) 200 OK (INVITE) � � 200 OK (INVITE) ANM ACK � CASE B 200 OK (INVITE) � � 200 OK (INVITE) (CON) ACK � ACK


Table 6.1.1.5-4: Mapping of Bearer capability to PSTN XML BearerCapability

ITC_value BC Information transfer capability

XML InformationTransferCapability

XML UserInfoLayer1Protocol

ITC_VA_1 Speech '00000' '00011' ITC_VA_2 3,1 kHz audio '10000' '00011' ITC_VA_3 Unrestricted digital inf. W/tone/ann '10001' '00110'

ETSI

ETSI TS 101 572-2 V1.2.1 (2014-07)67


TSS reference SIP NNI - SIP-I/Basic call/Sending_of_200_OK/ Selection criteria PICS 6.2.1/5 Test Purpose name Backward call indicator mapped into PSTN XML ProgressIndicator value 1 Test Purpose Ensure that on receipt of a 200 OK (INVITE) with encapsulated ANM/CON and the

backward call indicator is set to ISDN User Part not used all the way, a 200 OK INVITE is sent and the PSTN XML ProgressIndicator value is set to 1 (Call is not end-to-end ISDN: further progress information may be available in-band)

ISUP Parameter values ANM/CON: BCi ISDN User Part indicator = ISDN User Part not used all the way SIP Parameter values 200 OK INVITE

<?xml version="1.0" encoding="utf-8"?> PSTN ProgressIndicator … ProgressOctet4 ProgressDescription>0000001<


INVITE � � INVITE (IAM) CASE A 180 Ringing � � 180 Ringing (ACM- free) 200 OK (INVITE) � � 200 OK (INVITE) ANM ACK � � ACK CASE B 200 OK (INVITE) � � 200 OK (INVITE) (CON) ACK � � ACK


ETSI

ETSI TS 101 572-2 V1.2.1 (2014-07)68


TSS reference SIP NNI - SIP-I/Basic call/Sending_of_200_OK/ Selection criteria PICS 6.2.1/5 Test Purpose name Backward call indicator mapped into PSTN XML ProgressIndicator value 2 Test Purpose Ensure that on receipt of a 200 OK (INVITE) with encapsulated ANM/CON and the

backward call indicator is set to ISDN User Part used all the way and Terminating access non-ISDN, a 200 OK INVITE is sent and the PSTN XML ProgressIndicator value is set to 2 (Destination address is non-ISDN)

ISUP Parameter values ANM/CON: BCi ISDN User Part indicator = ISDN User Part used all the way ISDN access indicator = Terminating access non-ISDN

SIP Parameter values 200 OK INVITE <?xml version="1.0" encoding="utf-8"?> PSTN ProgressIndicator … ProgressOctet4 ProgressDescription>0000010<


INVITE � � INVITE (IAM) CASE A 180 Ringing � � 180 Ringing (ACM – free) 200 OK (INVITE) � � 200 OK (INVITE) (ANM) ACK � � ACK CASE B 200 OK (INVITE) � � 200 OK (INVITE) (CON) ACK � � ACK


ETSI

ETSI TS 101 572-2 V1.2.1 (2014-07)69


TSS reference SIP NNI - SIP-I/Basic call/Sending_of_200_OK/ Selection criteria PICS 6.2.1/5 Test Purpose name Backward call indicator mapped into PSTN XML ProgressIndicator value 7 Test Purpose Ensure that on receipt of a 200 OK INVITE with encapsulated ANM/CON and the backward

call indicator is set to ISDN User Part used all the way and Terminating access ISDN, a 200 OK INVITE is sent and the PSTN XML ProgressIndicator value is set to 7

ISUP Parameter values ANM/CON: BCi ISDN User Part indicator = ISDN User Part used all the way ISDN access indicator = Terminating access ISDN



INVITE � � INVITE (IAM) CASE A 180 Ringing � � 180 Ringing (ACM) 200 OK (INVITE) � � 200 OK (INVITE) (ANM) ACK � � ACK CASE B 200 OK (INVITE) � � 200 OK (INVITE) (CON) ACK � � ACK


ETSI

ETSI TS 101 572-2 V1.2.1 (2014-07)70


TSS reference SIP NNI - SIP-I/Basic call/Sending_of_200_OK/ Selection criteria PICS 6.2.1/5 Test Purpose name Optional backward call indicator mapped into PSTN XML ProgressIndicator value 8 Test Purpose Ensure that on receipt of a 200 OK INVITE with encapsulated ANM/CON and the optional

backward call indicator is to in-band information or an appropriate pattern is now available, a 200 OK INVITE is sent and the PSTN XML ProgressIndicator value is set to 8 (In-band information or appropriate pattern is now available)

ISUP Parameter values ANM/CON: Optional backward call indicator In-band information indicator = in-band information or an appropriate pattern is now available



INVITE � � INVITE (IAM) CASE A 180 Ringing � � 180 Ringing (ACM) 200 OK (INVITE) � � 200 OK (INVITE) (ANM) ACK � � ACK CASE B 200 OK (INVITE) � � 200 OK (INVITE) CON ACK � � ACK


ETSI

ETSI TS 101 572-2 V1.2.1 (2014-07)71


TSS reference SIP NNI - SIP-I/Basic call/Sending_of_200_OK/ Selection criteria PICS 6.2.1/5 Test Purpose name Receipt of TMU speech in 200 OK (ANM) with encapsulated ANM/CON, no BC present in

ATP Test Purpose Ensure that on receipt of a Transmission medium used parameter set to speech in the 200

OK INVITE with encapsulated ANM/CON, a 200 OK INVITE is sent and a PSTN XML BearerCapability element is present the InformationTransferCapability is set to Speech

ISUP Parameter values IAM: TMR = second InformationTransferCapability TMR prime = first InformationTransferCapability USI = first BearerCapability USI prime = second BearerCapability ANM/CON: Transmission medium used = speech

SIP Parameter values INVITE: PSTN XML MIME body <?xml version="1.0" encoding="utf-8"?> PSTN BearerCapability BCoctet3 CodingStandard>00< InformationTransferCapability>00000< …. BearerCapability BCoctet3 CodingStandard>00< InformationTransferCapability>10001< …. 200 OK INVITE <?xml version="1.0" encoding="utf-8"?> PSTN BearerCapability BCoctet3 CodingStandard>00< InformationTransferCapability>00000< …


INVITE � � INVITE (IAM) CASE A 180 Ringing � � 180 Ringing (ACM – free) 200 OK (INVITE) � � 200 OK (INVITE) (ANM) ACK � CASE B 200 OK (INVITE) � � 200 OK (CON) ACK � � ACK


ETSI

ETSI TS 101 572-2 V1.2.1 (2014-07)72


TSS reference SIP NNI - SIP-I/Basic call/Sending_of_200_OK/ Selection criteria PICS 6.2.1/5 Test Purpose name Receipt of TMU 3,1 kHz audio in200 OK (ANM) with encapsulated ANM/CON, no BC

present in ATP Test Purpose Ensure that on receipt of a Transmission medium used parameter set to 3,1 kHz audio in

the 200 OK INVITE with encapsulated ANM/CON, a 200 OK INVITE is sent and a PSTN XML BearerCapability element is present the InformationTransferCapability is set to 3,1 kHz audio

ISUP Parameter values IAM: TMR = second InformationTransferCapability TMR prime = first InformationTransferCapability USI = first BearerCapability USI prime = second BearerCapability ANM/CON: Transmission medium used = 3,1 kHz audio

SIP Parameter values INVITE: PSTN XML MIME body <?xml version="1.0" encoding="utf-8"?> PSTN BearerCapability BCoctet3 CodingStandard>00< InformationTransferCapability>10000< …. BearerCapability BCoctet3 CodingStandard>00< InformationTransferCapability>10001< …. 200 OK INVITE <?xml version="1.0" encoding="utf-8"?> PSTN BearerCapability BCoctet3 CodingStandard>00< InformationTransferCapability>10000< …


INVITE � � INVITE (IAM) CASE A 180 Ringing � � 180 Ringing (ACM) 200 OK (INVITE) � � 200 OK INVITE (ANM) ACK � CASE B 200 OK (INVITE) � � 200 OK (INVITE) CON ACK � � ACK


ETSI

ETSI TS 101 572-2 V1.2.1 (2014-07)73


TSS reference SIP NNI - SIP-I/Basic call/Sending_of_200_OK/ Selection criteria PICS 6.2.1/5 Test Purpose name Receipt of TMU, BC present in ATP PSTN XML BearerCapability sent in 200 OK Test Purpose Ensure that on receipt of a Transmission medium used parameter and in the ATP a Bearer

Capability IE in the 200 OK INVITE with encapsulated ANM/CON, a 200 OK INVITE is sent and a PSTN XML BearerCapability element is present the InformationTransferCapability is set as indicated in table 6.1.1.5-5

ISUP Parameter values IAM: TMR = second InformationTransferCapability TMR prime = first InformationTransferCapability USI = first BearerCapability USI prime = second BearerCapability ANM/CON: Transmission medium used, ATP Bearer Capability IE

SIP Parameter values 200 OK INVITE <?xml version="1.0" encoding="utf-8"?> PSTN BearerCapability BCoctet3 CodingStandard>00< InformationTransferCapability>ITC_value< …


INVITE � � INVITE (IAM) CASE A 180 Ringing � � 180 Ringing (ACM) 200 OK (INVITE) � � 200 OK (INVITE) (ANM) ACK � CASE B 200 OK (INVITE) � � CON ACK �


Table 6.1.1.5-5: Mapping of TMU and Bearer capability IE to PSTN XML BearerCapability

ITC_value ← 180 Ringing or 183 Session Progress ←ACM/CPG ITC_value_VA_01 PSTN XML BearerCapability = "Speech" TMU "Speech"

ATP BC "speech" ITC_value_VA_02 PSTN XML BearerCapability = "Speech" TMU "3,1 kHz audio"

ATP BC "speech" ITC_value_VA_03 PSTN XML BearerCapability = "3,1 kHz audio" TMU "Speech"

ATP BC "3,1 kHz audio" ITC_value_VA_04 PSTN XML BearerCapability = "3,1 kHz audio" TMU "3,1 kHz audio"

ATP BC "3,1 kHz audio"

ETSI

ETSI TS 101 572-2 V1.2.1 (2014-07)74

6.1.1.6 Sending of the Release message (REL)


TSS reference SIP NNI - SIP-I/Basic call/Sending_of_REL/ Selection criteria Test Purpose name BYE received in confirmed dialogue no Reason header included, a BYE with encapsulated

REL is sent Test Purpose Ensure that on receipt of a BYE request in confirmed dialogue and no Reason header is

present, a BYE with encapsulated REL message is sent. The cause indicator is set to No. 16 (normal clearing), the location is set to 'network beyond interworking point'

ISUP Parameter values REL: Cause indicator Cause Value = 16 (normal clearing) Location = network beyond interworking point

SIP Parameter values Comments Message flows SIP NNI MGCF SIP-I

INVITE � � INVITE (IAM) 100 Trying � 180 Ringing � � 180 Ringing (ACM – free) 200 OK (INVITE) � � 200 OK (INVITE) (ANM) ACK � BYE � � BYE (REL) 200 OK (BYE) � � 200 OK (BYE) (RLC)


TSS reference SIP NNI - SIP-I/Basic call/Sending_of_REL/ Selection criteria Test Purpose name BYE received in confirmed dialogue Reason header included, a BYE with encapsulated

REL is sent Test Purpose Ensure that on receipt of a BYE request in confirmed dialogue and a Reason header is

present, a BYE with encapsulated REL message is sent. The cause indicator is set to the Reason header cause value, the location is set to 'network beyond interworking point'

ISUP Parameter values REL: Cause indicator Cause Value = Cause_value Location = network beyond interworking point

SIP Parameter values BYE: Reason: Q.850 ; cause = Cause_value Comments The Cause_value is a PIXIT parameter Message flows SIP NNI MGCF SIP-I

INVITE � � INVITE (IAM) 100 Trying � 180 Ringing � � 180 Ringing (ACM – free) 200 OK (INVITE) � � 200 OK (INVITE) (ANM) ACK � � ACK BYE � � BYE (REL) 200 OK (BYE) � � 200 OK (BYE) (RLC)

ETSI

ETSI TS 101 572-2 V1.2.1 (2014-07)75


TSS reference SIP NNI - SIP-I/Basic call/Sending_of_REL/ Selection criteria Test Purpose name BYE received in early dialogue no Reason header included, a BYE with encapsulated REL

is sent Test Purpose Ensure that on receipt of a BYE request in early dialogue and no Reason header is

present, a BYE with encapsulated REL message is sent. The cause indicator is set to No. 16 (normal clearing), the location is set to 'network beyond interworking point'

ISUP Parameter values REL: Cause indicator Cause Value = 16 (normal clearing) Location = network beyond interworking point


INVITE � � INVITE (IAM) 18x � � 18x

(ACM (no indication or free) BYE � � BYE (REL) 200 OK (BYE) � � 200 OK (BYE) RLC 487 Request Terminated � � 487 Request Terminated ACK � � ACK


TSS reference SIP NNI - SIP-I/Basic call/Sending_of_REL/ Selection criteria Test Purpose name BYE received in early dialogue Reason header included, a BYE with encapsulated REL is

sent Test Purpose Ensure that on receipt of a BYE request in early dialogue and a Reason header is present,

a BYE with encapsulated REL message is sent. The cause indicator is set to the Reason header cause value, the location is set to 'network beyond interworking point'


SIP Parameter values BYE: Reason: Q.850; cause = Cause_value Comments The Cause_value is a PIXIT parameter Message flows SIP NNI MGCF SIP-I

INVITE � � INVITE (IAM) 18x � � 18x

(ACM (no indication or free) BYE � � BYE (REL) 200 OK (BYE) � � 200 OK (BYE) RLC 487 Request Terminated � � 487 Request Terminated ACK � � ACK

ETSI

ETSI TS 101 572-2 V1.2.1 (2014-07)76

TP number TP_106_005 Reference [1], clauses 7.2.2, 7.2.3.1.7 TSS reference SIP NNI - SIP-I/Basic call/Sending_of_REL/ Selection criteria Test Purpose name CANCEL received in early dialogue no Reason header included, a CANCEL with

encapsulated REL is sent Test Purpose Ensure that on receipt of a CANCEL request in early dialogue and no Reason header is

present, a CANCEL with encapsulated REL message is sent. The cause indicator is set to No. 16 (normal clearing), the location is set to 'network beyond interworking point'

ISUP Parameter values REL: Cause indicator Cause Value = 31 (normal unspecified) Location = network beyond interworking point


INVITE � � INVITE (IAM) 18x � � ACM

18x (ACM (no indication or free)

CANCEL � � CANCEL (REL) 200 OK (CANCEL) � � 200 OK (CANCEL)RLC 487 Request Terminated � � 487 Request Terminated ACK � � ACK


TSS reference SIP NNI - SIP-I/Basic call/Sending_of_REL/ Selection criteria Test Purpose name CANCEL received in early dialogue Reason header included, a CANCEL with

encapsulated REL is sent Test Purpose Ensure that on receipt of a CANCEL request in early dialogue and a Reason header is

present, a CANCEL with encapsulated REL message is sent. The cause indicator is set to the Reason header cause value, the location is set to 'network beyond interworking point'


SIP Parameter values CANCEL: Reason: Q.850; cause = Cause_value Comments The Cause_value is a PIXIT parameter Message flows SIP NNI MGCF SIP-I

INVITE � � INVITE (IAM) 18x � � ACM

18x (ACM (no indication or free)

CANCEL � � CANCEL (REL) 200 OK (CANCEL) � � 200 OK (CANCEL)RLC 487 Request Terminated � � 487 Request Terminated ACK � � ACK

ETSI

ETSI TS 101 572-2 V1.2.1 (2014-07)77


TSS reference SIP NNI - SIP-I/Basic call/Sending_of_REL/ Selection criteria PICS 6.2.1/5 Test Purpose name BYE received in confirmed dialogue PSTN XML HighLayerCompatibility present, a BYE

with encapsulated REL is sent containing a High layer compatibility IE Test Purpose Ensure that on receipt of a BYE request in confirmed dialogue and a PSTN XML

HighLayerCompatibility is present, a BYE with encapsulated REL is sent and an ATP is present containing a High layer compatibility IE. The value is mapped as indicated in table 6.1.1.6-1

ISUP Parameter values REL: ATP High layer compatibility High Layer Characteristic = HLC_value SIP Parameter values BYE:



INVITE � � INVITE (IAM) 100 Trying � 180 Ringing � � 180 Ringing (ACM –free) 200 OK (INVITE) � � 200 OK (INVITE) (ANM) ACK � BYE � � BYE (REL) 200 OK (BYE) � � 200 OK (RLC)


TSS reference SIP NNI - SIP-I/Basic call/Sending_of_REL/ Selection criteria PICS 6.2.1/5 Test Purpose name BYE received in early dialogue PSTN XML HighLayerCompatibility present, a BYE with

encapsulated REL is sent containing a High layer compatibility IE Test Purpose Ensure that on receipt of a BYE request in early dialogue and a PSTN XML

HighLayerCompatibility is present, a BYE with encapsulated REL is sent and an ATP is present containing a High layer compatibility IE. The value is mapped as indicated in table 6.1.1.6-1

ISUP Parameter values REL: ATP High layer compatibility High Layer Characteristic = HLC_value SIP Parameter values BYE:



INVITE � � INVITE (IAM) BYE � � BYE (REL) 200 OK (BYE) � � 200 OK (INVITE) RLC 487 Request Terminated � � 487 Request Terminated ACK � � ACK

ETSI

ETSI TS 101 572-2 V1.2.1 (2014-07)78


TSS reference SIP NNI - SIP-I/Basic call/Sending_of_REL/ Selection criteria PICS 6.2.1/5 Test Purpose name CANCEL received in early dialogue PSTN XML HighLayerCompatibility present, a

CANCEL with encapsulated REL is sent containing a High layer compatibility IE Test Purpose Ensure that on receipt of a CANCEL request in early dialogue and a PSTN XML

HighLayerCompatibility is present, a CANCEL with encapsulated REL is sent and an ATP is present containing a High layer compatibility IE. The value is mapped as indicated in table 6.1.1.6-1

ISUP Parameter values REL: ATP High layer compatibility High Layer Characteristic = HLC_value SIP Parameter values CANCEL



INVITE � � INVITE (IAM) CANCEL � � CANCEL (REL) 200 OK (CANCEL) � � 200 OK (CANCEL) (RLC) 487 Request Terminated � � 487 Request Terminated ACK � � ACK





ETSI

ETSI TS 101 572-2 V1.2.1 (2014-07)79


TSS reference SIP NNI - SIP-I/Basic call/Sending_of_REL/ Selection criteria PICS 6.2.1/5 Test Purpose name BYE received in confirmed dialogue PSTN XML LowLayerCompatibility present, a BYE

with encapsulated REL is sent containing a Low layer compatibility IE Test Purpose Ensure that on receipt of a BYE request in confirmed dialogue and a PSTN XML

LowLayerCompatibility is present, a BYE with encapsulated REL is sent and an ATP is present containing a Low layer compatibility IE. The value is mapped as indicated in table 6.1.1.6-2

ISUP Parameter values REL: ATP Low layer compatibility Information Transfer Capability = ITC_value SIP Parameter values <?xml version="1.0" encoding="utf-8"?>

PSTN LowLayerCompatibility> LLOctet3> CodingStandard>00< InformationTransferCapability>ITC_value<


INVITE � � INVITE (IAM) 100 Trying � � 100 Trying 180 Ringing � � 180 Ringing (ACM – free) 200 OK (INVITE) � � 200 OK (ANM) ACK � � ACK BYE � � BYE (REL) 200 OK (BYE) � � 200 OK (BYE) (RLC)


TSS reference SIP NNI - SIP-I/Basic call/Sending_of_REL/ Selection criteria PICS 6.2.1/5 Test Purpose name BYE received in early dialogue PSTN XML LowLayerCompatibility present, a BYE with

encapsulated REL is sent containing a Low layer compatibility IE Test Purpose Ensure that on receipt of a BYE request in early dialogue and a PSTN XML

LowLayerCompatibility is present, a BYE with encapsulated REL is sent and an ATP is present containing a Low layer compatibility IE. The value is mapped as indicated in table 6.1.1.6-2

ISUP Parameter values REL: ATP Low layer compatibility Information Transfer Capability = ITC_value SIP Parameter values BYE

<?xml version="1.0" encoding="utf-8"?> PSTN LowLayerCompatibility> LLOctet3> CodingStandard>00< InformationTransferCapability>ITC_value< …


INVITE � � INVITE (IAM) BYE � � BYE (RE)L 200 OK (BYE) � � 200 OK (BYE) (RLC) 487 Request Terminated � � 487 Request Terminated ACK � � ACK

ETSI

ETSI TS 101 572-2 V1.2.1 (2014-07)80


TSS reference SIP NNI - SIP-I/Basic call/Sending_of_REL/ Selection criteria PICS 6.2.1/5 Test Purpose name CANCEL received in early dialogue PSTN XML LowLayerCompatibility present, a CANCEL

with encapsulated REL is sent containing a Low layer compatibility IE Test Purpose Ensure that on receipt of a CANCEL request in early dialogue and a PSTN XML

LowLayerCompatibility is present, a CANCEL with encapsulated REL is sent and an ATP is present containing a Low layer compatibility IE. The value is mapped as indicated in table 6.1.1.6-2

ISUP Parameter values REL: ATP Low layer compatibility Information Transfer Capability = ITC_value SIP Parameter values CANCEL <?xml version="1.0" encoding="utf-8"?>

PSTN LowLayerCompatibility> LLOctet3> CodingStandard>00< InformationTransferCapability>ITC_value< …


INVITE � � INVITE (IAM) CANCEL � � CANCEL (REL) 200 OK (CANCEL) � � 200 OK (CANCEL) (RLC) 487 Request Terminated � � 487 Request Terminated ACK � � ACK



6.1.1.7 Receipt of the Release Message


TSS reference SIP NNI - SIP-I/Basic call/Receipt_of_REL/ Selection criteria Test Purpose name A REL is received, a BYE request is sent Test Purpose Ensure that on receipt of a BYE with encapsulated REL message in the confirmed

dialogue, a BYE is sent. The Reason header is present and the cause value is set to the received cause value in the REL Cause indicator

ISUP Parameter values REL: Cause indicator Cause Value = Cause_value SIP Parameter values BYE: Reason: Q.850 ; cause = Cause_value Comments Cause_value is a PIXIT parameter Message flows SIP NNI MGCF SIP-I

INVITE � � INVITE (IAM) 100 Trying � � 100 Trying 180 Ringing � � 180 Ringing (ACM – fee) 200 OK (INVITE) � � 200 OK (INVITE) (ANM) ACK � � ACK BYE � � BYE (REL) 200 OK (BYE) � � 200 OK (BYE) (RLC)

ETSI

ETSI TS 101 572-2 V1.2.1 (2014-07)81

TP number TP_107_001A Reference [1], clause 7.2.2 [2], clause 7.2.3.1.8

TSS reference SIP NNI - SIP-I/Basic call/Receipt_of_REL/ Selection criteria Test Purpose name A REL is received, a BYE request is sent Test Purpose Ensure that on receipt of a BYE with encapsulated REL message in the confirmed

dialogue, a BYE is sent. Ensure that if the Reason Header field was not received, then the received ISUP Cause value being received in the encapsulated ISUP REL message shall be mapped into SIP Reason header fields as specified

ISUP Parameter values REL: Cause indicator Cause Value = Cause_value SIP Parameter values BYE: Reason: Q.850; cause = Cause_value Comments Cause_value is a PIXIT parameter Message flows SIP NNI MGCF SIP-I

INVITE � � INVITE (IAM) 100 Trying � � 100 Trying 180 Ringing � � 180 Ringing (ACM – fee) 200 OK (INVITE) � � 200 OK (INVITE) (ANM) ACK � � ACK BYE � � BYE (REL) 200 OK (BYE) � � 200 OK (BYE) (RLC)


TSS reference SIP NNI - SIP-I/Basic call/Receipt_of_REL/ Selection criteria Test Purpose name A SIP_final_Response with encapsulated REL is received before an early dialogue is

established, a final response is sent Test Purpose Ensure that on receipt of a SIP_final_Response with encapsulated REL message before

an early dialogue is established a SIP final response is sent. The response code is derived from the Cause value received in the REL according the rules described in table 6.1.1.7-1. The cause value of the received REL is present in the Reason header of the sent final response

ISUP Parameter values REL: Cause indicator Cause Value = Cause_value SIP Parameter values 4xx/5xx/6xx: Reason: Q.850; cause = Cause_value Comments Message flows SIP NNI MGCF SIP-I

INVITE � � INVITE (IAM) 100 Trying � � Trying SIP_final_Response � � SIP_final_Response (REL) ACK � � ACK (RLC)

ETSI

ETSI TS 101 572-2 V1.2.1 (2014-07)82


TSS reference SIP NNI - SIP-I/Basic call/Receipt_of_REL/ Selection criteria Test Purpose name A SIP_final_Response with encapsulated REL is received after an early dialogue is

established (180), a final response is sent Test Purpose Ensure that on receipt of a SIP_final_Response with encapsulated REL message after an

early dialogue due to sending a 180 Ringing is established a SIP final response is sent. The response code is derived from the Cause value received in the REL according the rules described in table 6.1.1.7-1. The cause value of the received REL is present in the Reason header of the sent final response

ISUP Parameter values ACM: BCi Called party status = subscriber free REL: Cause indicator Cause Value = Cause_value

SIP Parameter values 4xx/5xx/6xx: Reason: Q.850; cause = Cause_value Comments Message flows SIP NNI MGCF SIP-I

INVITE � � INVITE (IAM) 180 Ringing � � 180 Ringing (ACM) SIP_final_Response � � SIP_final_Response (REL) ACK � � ACK (RLC)



established (181), a final response is sent Test Purpose Ensure that on receipt of a SIP_final_Response with encapsulated REL message after an

early dialogue due to sending a 181 Call Is Being Forwarded is established a SIP final response is sent. The response code is derived from the Cause value received in the REL according the rules described in table 6.1.1.7-1. The cause value of the received REL is present in the Reason header of the sent final response

ISUP Parameter values ACM: BCi Called party status = no indication Redirection number Call diversion information Generic notification = 'Call is diverted' REL: Cause indicator Cause Value = Cause_value

SIP Parameter values 4xx/5xx/6xx: Reason: Q.850; cause = Cause_value Comments Message flows SIP NNI MGCF SIP-I

INVITE � � INVITE (IAM) 181 Call Is Being Forwarded � � 181 Call Is Being

Forwarded (ACM) SIP_final_Response � � SIP_final_Response

(REL) ACK � � (ACK) RLC

ETSI

ETSI TS 101 572-2 V1.2.1 (2014-07)83



established (183), a final response is sent Test Purpose Ensure that on receipt of a REL message after an early dialogue due to sending a 183

Session Progress is established a SIP final response is sent. The response code is derived from the Cause value received in the REL according the rules described in table 6.1.1.7-1. The cause value of the received REL is present in the Reason header of the sent final response

ISUP Parameter values ACM: BCi Called party status = no indication oBCi in-band info available REL: Cause indicator Cause Value = Cause_value

SIP Parameter values 4xx/5xx/6xx: Reason: Q.850ause = Cause_value Comments Message flows SIP NNI MGCF SIP-I


(ACM) SIP_final_Response � � SIP_final_Response

(REL) ACK � � (ACK) RLC


TSS reference SIP NNI - SIP-I/Basic call/Receipt_of_REL/ Selection criteria PICS 6.2.1/5 Test Purpose name An ATP Progress indicator IE present in a SIP_final_Response with encapsulated REL is

mapped into the PSTN XML ProgressIndicator in the sent final response Test Purpose Ensure that on receipt of a SIP_final_Response with encapsulated REL message and

Progress Indicator IE is present in an ATP, a SIP final response as indicated in table 6.1.1.7-5 is sent, a PSTN XML ProgressIndicator is contained and the Progress Description is derived from the received REL Progress indicator as indicated in table 6.1.1.7-2

ISUP Parameter values REL: ATP Progress Indicator = PI_value SIP Parameter values 4xx/5xx/6xx:

<?xml version="1.0" encoding="utf-8"?> PSTN ProgressIndicator ProgressOctet3 CodingStandard>00< Location<yyyy> ProgressOctet4 ProgressDescription>PI_value<


INVITE � � (INVITE) IAM 180 Ringing � � 180 Ringing (ACM) SIP_final_Response � � SIP_final_Response (REL) ACK � � ACK (RLC)

ETSI

ETSI TS 101 572-2 V1.2.1 (2014-07)84


TSS reference SIP NNI - SIP-I/Basic call/Receipt_of_REL/ Selection criteria PICS 6.2.1/5 Test Purpose name An ATP High Layer Compatibility IE present in a REL is mapped into the PSTN XML

HighLayerCompatibility in the sent final response Test Purpose Ensure that on receipt of a SIP_final_Response with encapsulated REL message and High

Layer Compatibility IE is present in an ATP, a SIP final response as indicated in table 6.1.1.7-5 is sent, a PSTN XML HighLayerCompatibility is contained and the HighLayerCharacteristics is derived from the received REL High Layer Compatibility as indicated in table 6.1.1.7-3

ISUP Parameter values REL: ATP High Layer Compatibility = HLC_value SIP Parameter values 4xx/5xx/6xx:



INVITE � � INVITE (IAM) 180 Ringing � � 180 Ringing (ACM) SIP_final_Response � � SIP_final_Response (REL) ACK � � (ACK) RLC


TSS reference SIP NNI - SIP-I/Basic call/Receipt_of_REL/ Selection criteria PICS 6.2.1/5 Test Purpose name An ATP Low Layer Compatibility IE present in a REL is mapped into the PSTN XML

LowLayerCompatibility in the sent final response Test Purpose Ensure that on receipt of a SIP_final_Response with encapsulated REL message and Low

Layer Compatibility IE is present in an ATP, a SIP final response as indicated in table 6.1.1.7-5 is sent, a PSTN XML LowLayerCompatibility is contained and the InformationTransferCapability is derived from the received REL Low Layer Compatibility as indicated in table 6.1.1.7-4

ISUP Parameter values REL: ATP Low Layer Compatibility = ITC_value SIP Parameter values 4xx/5xx/6xx:

<?xml version="1.0" encoding="utf-8"?> PSTN LowLayerCompatibility> LLOctet3> CodingStandard>00< InformationTransferCapability>ITC_value< LLOctet4> TransferMode>00< InformationTransferRate>10000<


INVITE � � INVITE (IAM) 180 Ringing � � 180 Ringing (ACM –free) SIP_final_Response � � SIP_final_Response (REL) ACK � � (ACK) RLC

ETSI

ETSI TS 101 572-2 V1.2.1 (2014-07)85

Table 6.1.1.7-1: Receipt of the Release message (REL)

← SIP_final_Response ← REL Status code Cause parameter VA_01 404 Not Found Cause value No. 1 (unallocated (unassigned)

number) VA_02 604 Does not exist anywhere Cause value No 2 (no route to network) VA_03 604 Does not exist anywhere Cause value No 3 (no route to destination) VA_04 500 Server Internal error Cause value No. 4 (Send special information

tone) VA_05 404 Not Found Cause value No. 5 (Misdialled trunk prefix) VA_06 486 Busy Here Cause value No. 17 (user busy) VA_07 480 Temporarily unavailable Cause value No 18 (no user responding) VA_08 480 Temporarily unavailable Cause value No 19 (no answer from the user) VA_09 480 Temporarily unavailable Cause value No. 20 (subscriber absent) VA_10 603 Decline Cause value No 21 (call rejected), Location =

000 / user (U) VA_11 403 Forbidden Cause value No 21 (call rejected) , Location not

equal 000 / user (U) VA_12 410 Gone Cause value No 22 (number changed) VA_13 410 Gone Cause value No 23 (Re-route to new

destination) VA_14 433 Anonymity Disallowed Cause value No. 24 (call rejected due to ACR

supplementary service) VA_15 483 Too many hops Cause value No 25 (Exchange routing error) VA_16 480 Temporarily unavailable Cause value No 26 (Non-selected user clearing) VA_17 502 Bad Gateway Cause value No 27 (destination out of order) VA_18 484 Address Incomplete Cause value No. 28 invalid number format

(address incomplete) VA_19 501 Not Implemented Cause value No 29 (facility rejected) VA_20 480 Temporarily unavailable Cause value No 31 (normal unspecified) (class

default) VA_21 486 Busy here Cause value No 34 (No circuit/channel available)

CCBS indicator = CCBS possible VA_22 480 Temporarily unavailable Cause value No 34 (No circuit/channel available)

CCBS indicator = CCBS not possible or absent VA_23 500 Server Internal error Cause value No 38 (Network out of order) VA_24 503 Service Unavailable Cause value No 41 (Temporary failure) VA_25 503 Service Unavailable Cause value No 42 (Switching equipment

congestion) VA_26 500 Server Internal error Cause value No 43 (Access information

discarded) VA_27 503 Service Unavailable Cause value No 44 (Requested channel not

available) VA_28 500 Server Internal error Cause value No 46 (Precedence call blocked) VA_29 503 Service Unavailable Cause value No 47 (Resource unavailable (class

default)) VA_30 488 Not acceptable here Cause value No 50 (requested facility no

subscribed) VA_31 603 Decline Cause value No 55 (Incoming class barred

within Closed User Group (CUG)) VA_32 603 Decline Cause value No 57 (bearer capability not

authorized) VA_33 503 Service Unavailable Cause value No 58 (bearer capability not

presently available) VA_34 501 Not Implemented Cause value No 63 (service option not available,

unspecified) (class default)

VA_35 500 Server Internal error Cause value No 65 Bearer capability not implemented

VA_36 501 Not Implemented Cause value No 69 (Requested facility not implemented)

VA_37 501 Not Implemented Cause value No 70 (Only restricted digital information capability available)

ETSI

ETSI TS 101 572-2 V1.2.1 (2014-07)86

← SIP_final_Response ← REL Status code Cause parameter VA_38 501 Not Implemented Cause value No 79 (Service or option not

implemented(class default)) VA_39 403 Forbidden Cause value No 87 (User not member of Closed

User Group(CUG)) VA_40 606 Not acceptable Cause value No 88 (incompatible destination) VA_41 403 Forbidden Cause value No 90 (Non existing Closed User

Group (CUG) ) VA_42 500 Server Internal error Cause value No 91 (invalid transit network

selection) VA_43 500 Server Internal error Cause value No 95 (invalid message)

(class default) VA_44 501 Not Implemented Cause value No 97 (Message type

non-existent or not implemented) VA_45 501 Not Implemented Cause value No 99 (information

element/parameter non-existent or not implemented))

VA_46 501 Not Implemented Cause value No 98 (Message not compatible with call state or message type non-existent or not implemented)

VA_47 480 Temporarily unavailable Cause value No. 102 (recovery on timer expiry) VA_48 501 Not Implemented Cause value No 103 (Non-existent parameter

passed on) VA_49 501 Not Implemented Cause value No 110 (Message with

unrecognized Parameter, discarded) VA_50 400 Bad Request Cause value No. 111 (protocol error,


VA_51 500 Server Internal error Cause value No. 127 (interworking unspecified) (class default)




'0000001'



PI_VA_6 In-band information or an appropriate pattern is now available

'0001000'





ETSI

ETSI TS 101 572-2 V1.2.1 (2014-07)87



Table 6.1.1.7-5: Receipt of the Release message (REL)

← SIP_final_Response ← REL Status code Cause parameter VA_01 480 Temporarily unavailable Cause value No 19 (no answer from the user) VA_02 603 Decline Cause value No 21 (call rejected), Location =

000 / user (U) VA_03 501 Not Implemented Cause value No 63 (service option not available,


VA_04 480 Temporarily unavailable Cause value No. 102 (recovery on timer expiry) VA_05 500 Server Internal error Cause value No. 127 (interworking unspecified)

(class default)

6.1.1.8 Void

6.1.1.9 Void

6.1.1.10 Void

6.1.2 Signalling Interworking of a Call from SIP-I based circuit-switched core network towards the IP Multimedia Subsystem

6.1.2.1 Sending of INVITE


TSS reference SIP-I-SIP/Basic call/Sending_of_INVITE/ Selection criteria Test Purpose name IAM received, a INVITE is sent Test Purpose Ensure that on receipt of an INVITE with encapsulated IAM message, an INVITE request is

sent ISUP Parameter values SIP Parameter values Comments Message flows SIP I MGCF SIP-NNI

INVITE (IAM) � � INVITE � 100 Trying


ETSI

ETSI TS 101 572-2 V1.2.1 (2014-07)88


TSS reference SIP-I-SIP/Basic call/Sending_of_INVITE/ Selection criteria PICS 6.2.1/11 Test Purpose name Information request procedure successful, Calling party number in INF received Test Purpose Ensure that on receipt of an IAM and no Calling party number is present, an Information

Request (INR) message is sent. On receipt of an Information (INF) message containing a calling party number the initial INVITE request is sent

ISUP Parameter values IAM: No calling party number present INR: Calling party address request indicator=calling party address requested INF: Calling party address response=calling party address included Calling party number

SIP Parameter values Comments Message flows SIP-I MGCF SIP-NNI

INVITE (IAM) � 183 Session Progress (INR) � INFO (INF) � � INVITE 200 OK (INFO) � � 100 Trying



TSS reference SIP-I-SIP/Basic call/Sending_of_INVITE/ Selection criteria PICS 6.2.1/11 AND PICS 6.2.1/12 Test Purpose name Information request procedure not successful, no Calling party number in INF received, the

call is rejected Test Purpose Ensure that on receipt of an INVITE with encapsulated IAM and no Calling party number is

present, an Information Request (INR) message is sent. On receipt of an Information (INF) message and no Calling party number is present, the call is rejected

ISUP Parameter values IAM: No calling party number present INR: Calling party address request indicator=calling party address requested INF: Calling party address response=calling party address not included


INVITE (IAM) � 183 Session Progress (INR) � INFO (INF) � 4xx/5xx/6xx (REL) � ACK �


ETSI

ETSI TS 101 572-2 V1.2.1 (2014-07)89


TSS reference SIP-I-SIP/Basic call/Sending_of_INVITE/ Selection criteria PICS 6.2.1/11 AND NOT PICS 6.2.1/12 Test Purpose name Information request procedure not successful, no Calling party number in INF received, the

call is continued Test Purpose Ensure that on receipt of an IAM and no Calling party number is present, an Information

Request (INR) message is sent. On receipt of an Information (INF) message and no Calling party number is present, the call is continued

ISUP Parameter values IAM: No calling party number present INR: Calling party address request indicator=calling party address requested INF: Calling party address response=calling party address not included


INVITE (IAM) � 183 Session Progress (INR) � INFO (INF) � � INVITE � 100 Trying



TSS reference SIP-I-SIP/Basic call/Sending_of_INVITE/ Selection criteria PICS 6.2.1/11 Test Purpose name Information request procedure not successful, T 33 is expired Test Purpose Ensure that on receipt of an INVITE with encapsulated IAM and no Calling party number is

present, an Information Request (INR) message is sent. If timer T33 is expired, the call is rejected

ISUP Parameter values IAM: No calling party number present INR: Calling party address request indicator=calling party address requested


INVITE (IAM) � 183 Session Progress (INR) � Start T33

4xx/5xx/6xx (REL) � T33 Expiry

ACK � Apply post test routine

TP number TP_201_009 Reference [1], clause 7.3.1 [2], clause 7.2.3.2.1.4 b)

TSS reference SIP-I-SIP/Basic call/Sending_of_INVITE/ Selection criteria Test Purpose name End of address signalling determined by receipt of the maximum number of digits used

in the national numbering plan Test Purpose Ensure that on receipt of an INVITE with encapsulated IAM and the called party number

contains maximum number of digits used in the national numbering plan, the initial INVITE is sent

ISUP Parameter values SIP Parameter values Comments Message flows SIP-I MGCF SIP-NNI



ETSI

ETSI TS 101 572-2 V1.2.1 (2014-07)90

TP number TP_201_010 Reference [1], clause 7.3.1 [2], clause 7.2.3.2.1.4 c)

TSS reference SIP-I-SIP/Basic call/Sending_of_INVITE/ Selection criteria Test Purpose name End of address signalling determined by receipt of sufficient number of digits to route the

call to the called party Test Purpose Ensure that on receipt of an INVITE with encapsulated IAM and the called party number

contains a sufficient number of digits to route the call to the called party, the initial INVITE is sent

ISUP Parameter values SIP Parameter values Comments Message flows SIP-I MGCF SIP-NNI




TSS reference SIP-I-SIP/Basic call/Sending_of_INVITE/ Selection criteria PICS 6.2.3/3 Test Purpose name A PSTN XML SendingCompleteIndication is sent if the end of the address signalling is

determined Test Purpose Ensure that the end of the address signalling is determined a PSTN XML

SendingCompleteIndication is sent ISUP Parameter values SIP Parameter values INVITE

<?xml version="1.0" encoding="utf-8"?> PSTN sendingCompleteIndication</

Comments Message flows SIP-I MGCF SIP-NNI

INVITE (IAM) � � INVITE Apply post test routine

ETSI

ETSI TS 101 572-2 V1.2.1 (2014-07)91


TSS reference SIP-I - SIP NNI/Basic call/Sending_of_INVITE/ Selection criteria PICS 6.2.1/5 AND PICS 6.2.4/1 AND PICS 6.2.4/8 Test Purpose name Mapping of USI and USI prime into PSTN XML BearerCapability element Test Purpose Ensure that on receipt of an INVITE with encapsulated IAM that includes a USI and USI

Prime parameter then the SUT: • Map the USI Prime into the second Bearer Capability stated in the XML

BearerCapability element and • The first offered codec is the CLEARMODE codec • Map the USI into the first Bearer Capability stated in the XML BearerCapability

element and • The second offered codec is a Audio codec

ISUP Parameter values IAM: USI=speech or 3,1 kHz audio USI prime=unrestricted digital info with T/A TMR Prime: 64 kBit/s preferred ATP(HLC Video Telephony)

SIP Parameter values INVITE: <?xml version="1.0" encoding="utf-8"?> PSTN BearerCapability BCoctet3 CodingStandard>00< InformationTransferCapability>mapped from USI< …. BearerCapability BCoctet3 CodingStandard>00< InformationTransferCapability>mapped from USI prime< …. SDP: m=audio <proper port number> RTP/AVP CLEARMODE 8 …




ETSI

ETSI TS 101 572-2 V1.2.1 (2014-07)92


TSS reference SIP-I - SIP NNI/Basic call/Sending_of_INVITE/ Selection criteria Test Purpose name Called party number is mapped into Request URI in the sent INVITE request Test Purpose Ensure that on receipt of an INVITE with encapsulated IAM the called party number is

mapped into the Request URI of the sent INVITE request: • If the nature of address indicator is set to 'National (significant) number' then the

country code of the network in which the SUT is located and a leading '+' is inserted before the number digits received in the Called party number

• If the nature of address set to 'International number' a '+' is inserted before the number digits received in the Called party number

ISUP Parameter values IAM: Called party number= National (significant) number or International number SIP Parameter values INVITE: Request URI

sip: '+CC' <called party number digits>@hostportion; user=phone or tel: '+CC' <called party number digits> if the called party number is a national number sip: '+' <called party number digits>@hostportion; user=phone or tel: '+' <called party number digits> if the called party number is an international number





TSS reference SIP-I - SIP NNI/Basic call/Sending_of_INVITE/ Selection criteria Test Purpose name Called party number is mapped into To header in the sent INVITE request Test Purpose Ensure that on receipt of an INVITE with encapsulated IAM the called party number is

mapped into the To header of the sent INVITE request: • If the nature of address indicator is set to 'National (significant) number' then the

country code of the network in which the SUT is located and a leading '+' is inserted before the number digits received in the Called party number

• If the nature of address set to 'International number' a '+' is inserted before the number digits received in the Called party number

ISUP Parameter values IAM: Called party number= National (significant) number or International number SIP Parameter values INVITE: To

sip: '+CC' <called party number digits>@hostportion; user=phone or tel: '+CC' <called party number digits> if the called party number is a national number sip: '+' <called party number digits>@hostportion; user=phone or tel: '+' <called party number digits> if the called party number is an international number




ETSI

ETSI TS 101 572-2 V1.2.1 (2014-07)93


TSS reference SIP-I - SIP NNI/Basic call/Sending_of_INVITE/ Selection criteria PICS 6.2.4/3 Test Purpose name Mapping of TMR speech into SDP Test Purpose Ensure that on receipt of an INVITE with encapsulated IAM the TMR speech is mapped

into the SDP m-line a a attributes ISUP Parameter values IAM: TMR=speech SIP Parameter values INVITE:

SDP m=audio <port #> RTP/AVP 0 [additional codes] a=rtpmap: 0 PCMU/8000 OR m=audio <port #> RTP/AVP 8 [additional codes] a=rtpmap: 8 PCMA/8000 OR m=audio <port #> RTP/AVP <dynamic-PT> [additional codes] a=rtpmap: <dynamic-PT> PCMU/8000 OR m=audio <port #> RTP/AVP <dynamic-PT> [additional codes] a=rtpmap: <dynamic-PT> PCMA/8000


IAM � � INVITE � 100 Trying



TSS reference SIP-I - SIP NNI/Basic call/Sending_of_INVITE/ Selection criteria PICS 6.2.4/4 Test Purpose name Mapping of TMR 3,1 kHz audio into SDP Test Purpose Ensure that on receipt of an INVITE with encapsulated IAM the TMR 3,1 kHz audio is

mapped into the SDP m-line a attributes ISUP Parameter values IAM: TMR=TMR_value SIP Parameter values INVITE:

SDP m=audio <port #> RTP/AVP 0 [additional codes] a=rtpmap: 0 PCMU/8000 OR m=audio <port #> RTP/AVP 8 [additional codes] a=rtpmap: 8 PCMA/8000 OR m=audio <port #> RTP/AVP <dynamic-PT> [additional codes] a=rtpmap: <dynamic-PT> PCMU/8000 OR m=audio <port #> RTP/AVP <dynamic-PT> [additional codes] a=rtpmap: <dynamic-PT> PCMA/8000




ETSI

ETSI TS 101 572-2 V1.2.1 (2014-07)94


TSS reference SIP-I - SIP NNI/Basic call/Sending_of_INVITE/ Selection criteria PICS 6.2.4/2 Test Purpose name Mapping of TMR 64 kBit/s unrestricted into SDP Test Purpose Ensure that on receipt of an INVITE with encapsulated IAM the TMR 64 kBit/s

unrestricted is mapped into the SDP m-line a attributes ISUP Parameter values IAM: TMR=64 kBit/s unrestricted SIP Parameter values INVITE:

SDP m=audio <port #> RTP/AVP <dynamic-PT> a=rtpmap: <dynamic-PT> CLEARMODE/8000






TSS reference SIP-I - SIP NNI/Basic call/Sending_of_INVITE/ Selection criteria Test Purpose name AMR codec included Test Purpose Ensure that on receipt of an INVITE with encapsulated IAM an INVITE is sent. If the

received IAM contains a TMR set to speech or 3,1 kHz audio, the SDP in the sent INVITE contains an AMR codec

ISUP Parameter values IAM: TMR=speech or 3,1 kHz audio SIP Parameter values INVITE:

SDP: m=audio <proper port number> RTP/AVP … Dynamic PT a = <rtpmap Dynamic PT> AMR




ETSI

ETSI TS 101 572-2 V1.2.1 (2014-07)95


TSS reference SIP-I - SIP NNI/Basic call/Sending_of_INVITE/ Selection criteria PICS 6.2.4/3 Test Purpose name Mapping of USI parameter Information Transfer Capability speech Test Purpose Ensure that on receipt of an INVITE with encapsulated IAM the USI Information Transfer

Capability speech and User Information Layer 1 Protocol Indicator "G.711 μ-law" or "G.711 A-law is mapped into the SDP m-line audio codec PCMA or PCMU

ISUP Parameter values IAM: User service information USI Information Transfer Capability speech Information Layer 1 Protocol Indicator G.711 μ-law or G.711 A-law

SIP Parameter values INVITE: SDP m=<port> RTP/AVP 8 a= rtpmap: 8 PCMA/8000 or m=audio <port> RTP/AVP 0 a= rtpmap:0 PCMU/8000





TSS reference SIP-I - SIP NNI/Basic call/Sending_of_INVITE/ Selection criteria PICS 6.2.4/7 Test Purpose name Mapping of USI parameter Information Transfer Capability 3.1 kHz audio and HLC

Facsimile Group 2/3 Test Purpose Ensure that on receipt of an INVITE with encapsulated IAM the USI Information Transfer

Capability 3.1 kHz audio and User Information Layer 1 Protocol Indicator "G.711 μ-law" or "G.711 A-law and ATP HLC "Facsimile Group 2/3" is mapped into the SDP m-line image udptl or tcptl.

ISUP Parameter values IAM: User service information USI Information Transfer Capability 3.1 kHz audio ATP High Layer Compatibility High Layer Characteristics Facsimile Group 2/3

SIP Parameter values INVITE: SDP m=image udptl t38 or m=image tcptl t38




ETSI

ETSI TS 101 572-2 V1.2.1 (2014-07)96


TSS reference SIP-I - SIP NNI/Basic call/Sending_of_INVITE/ Selection criteria PICS 6.2.4/2 Test Purpose name Mapping of USI parameter Information Transfer Capability UDI Test Purpose Ensure that on receipt of an INVITE with encapsulated IAM the USI Information Transfer

Capability Unrestricted digital information is mapped into the SDP m-line audio codec CLEARMODE

ISUP Parameter values IAM: User service information USI Information Transfer Capability Unrestricted digital information

SIP Parameter values INVITE: SDP m=<media> RTP/AVP <Dynamic payload type> a= rtpmap: <Dynamic payload type> CLEARMODE/8000





TP number TP_201_029 Reference [1], clause 7.3.1 [2], clause 7.2.3.2.2.3A

TSS reference SIP-I - SIP NNI/Basic call/Sending_of_INVITE/ Selection criteria Test Purpose name Mapping of Calling party's category into cpc parameter Test Purpose Ensure that on receipt of an INVITE with encapsulated IAM the calling party's category

CPC_value is mapped into the 'cpc' parameter in the P-Asserted-Identity and the Accept-Language header in the sent INVITE as described in table 6.1.2.1-3

ISUP Parameter values IAM: Calling party's category SIP Parameter values INVITE: P-Asserted-Identity Comments Message flows SIP-I MGCF SIP NNI



Table 6.1.2.1-3: Mapping of Calling's party category into 'cpc' parameter and Accept-Language header

CPC_value ISUP IAM parameter SIP Parameters Calling party's category "cpc" URI parameter in

P-Asserted-Identity Accept-Language

VA_01 operator, language French Operator fr VA_02 operator, language English Operator en VA_03 operator, language German Operator de VA_04 operator, language Russian Operator ru VA_05 operator, language Spanish Operator es VA_06 ordinary calling subscriber Ordinary VA_07 Test call Test VA_08 Payphone Payphone VA_09 calling party's category unknown at this time Unknown VA_10 mobile terminal located in the home PLMN mobile-hplmn VA_11 mobile terminal located in a visited PLMN mobile-vplmn VA_12 emergency service call per ANSI Standard emergency

ETSI

ETSI TS 101 572-2 V1.2.1 (2014-07)97


TSS reference SIP-I - SIP NNI/Basic call/Sending_of_INVITE/ Selection criteria PICS 6.2.1/8 Test Purpose name HOP counter procedure supported Test Purpose Ensure that on receipt of the HOP counter parameter, the value is mapped into the

Max-Forwards header. The value of the Max-Forwards header is created from the HOP counter value by applying a given factor

ISUP Parameter values IAM: HOP SIP Parameter values INVITE: Max-Forwards Comments The factor used to map from Hop Counter to Max-Forwards for a given call will depend on

call origin, and will be provisioned at the O-MGCF based on network topology, trust domain rules, and bilateral agreement.

Message flows SIP-I MGCF SIP NNI INVITE (IAM) � � INVITE � 100 Trying



TSS reference SIP-I - SIP NNI/Basic call/Sending_of_INVITE/ Selection criteria Test Purpose name The O-MGCF inserts an IMS Communication Service Identifier Test Purpose For speech and video calls, the SUT shall insert an IMS Communication Service Identifier,

indicating the IMS Multimedia Telephony Communication Service ISUP Parameter values SIP Parameter values INVITE: Contact: icsi-ref

Accept-Contact: P-Asserted-Service: urn:urn-7:3gpp-service.ims.icsi.mmtel

Comments Message flows SIP-I MGCF SIP NNI




TSS reference SIP-I - SIP NNI/Basic call/Sending_of_INVITE/ Selection criteria PICS 6.2.1/9 Test Purpose name Support of P-Early-Media header Test Purpose Ensure that on receipt of an INVITE with encapsulated IAM a P-Early-Media header is

present in the sent INVITE request ISUP Parameter values SIP Parameter values INVITE: P-Early-Media: supported Comments Message flows SIP-I MGCF SIP NNI



ETSI

ETSI TS 101 572-2 V1.2.1 (2014-07)98


TSS reference SIP-I - SIP NNI/Basic call/Sending_of_INVITE/ Selection criteria PICS 6.2.1/5 Test Purpose name Mapping of High Layer Compatibility IE into PSTN XML HighLayerCompatibility Test Purpose Ensure stat on receipt of an INVITE with encapsulated IAM and an ATP parameter is

present containing a High Layer Compatibility IE a PSTN XML HighLayerCompatibility element is present derived according the HLC_VA as indicated in table 6.1.2.1-4

ISUP Parameter values IAM: ATP High Layer Compatibility High Layer Characteristics=HLC_VA

SIP Parameter values INVITE: PSTN XML MIME body <?xml version="1.0" encoding="utf-8"?> PSTN HighLayerCompatibility HLOctet3 CodingStandard>00< Interpretation>100< PresentationMethod>01< HLOctet4 HighLayerCharacteristics>HLC_VA<




Table 6.1.2.1-4: Mapping of ISUP ATP High layer compatibility into PSTN XML HighLayerCharacteristic

HLC_VA DSS1 High layer characteristics identification XML HighLayerCharacteristic HLC_VA_1 Telephony '0000001' HLC_VA_2 Facsimile Group 2/3 '0000100' HLC_VA_3 Facsimile Group 4 Class I '0100001' HLC_VA_4 Facsimile service Group 4, Classes II and III '0100100' HLC_VA_5 Syntax based Videotex '0110010' HLC_VA_6 International Videotex interworking via gateways

or interworking units '0110011'

HLC_VA_7 Telex service '0110101' HLC_VA_8 FTAM application '1000010'

ETSI

ETSI TS 101 572-2 V1.2.1 (2014-07)99


TSS reference SIP-I - SIP NNI/Basic call/Sending_of_INVITE/ Selection criteria PICS 6.2.1/5 Test Purpose name Mapping of Low Layer Compatibility IE into PSTN XML LowLayerCompatibility Test Purpose Ensure stat on receipt of an INVITE with encapsulated IAM and an ATP parameter is

present containing a Low Layer Compatibility IE a PSTN XML LowLayerCompatibility element is present derived according the ITC_VA as indicated in table 6.1.2.1-5

ISUP Parameter values IAM: ATP Low Layer Compatibility InformationTransferCapability=ITC_VA

SIP Parameter values INVITE: <?xml version="1.0" encoding="utf-8"?> PSTN LowLayerCompatibility> LLOctet3> CodingStandard>00< InformationTransferCapability>ITC_VA< LLOctet4> TransferMode>00< InformationTransferRate>10000<




Table 6.1.2.1-5: Mapping of ISUP ATP Low Layer Compatibility into PSTN XML LowLayerCompatibility

ITC_VA LLC Information transfer capability XML LLC InformationTransferCapability ITC_VA_1 Speech '00000' ITC_VA_2 3,1 kHz audio '10000' ITC_VA_3 Unrestricted digital info '01001' ITC_VA_4 7 kHz audio '10001'


TSS reference SIP-I - SIP NNI/Basic call/Sending_of_INVITE/ Selection criteria PICS 6.2.1/5 Test Purpose name Mapping of Bearer Capability IE into PSTN XML BearerCapability Test Purpose Ensure stat on receipt of an INVITE with encapsulated IAM and an USI parameter is

present ,a PSTN XML BearerCapability element is present derived according the ITC_value as indicated in table 6.1.2.1-6

ISUP Parameter values IAM: USI Information Transfer Capability=ITC_value

SIP Parameter values INVITE: <?xml version="1.0" encoding="utf-8"?> PSTN BearerCapability BCoctet3 CodingStandard>00< InformationTransferCapability>ITC_value< BCoctet4 TransferMode>00< InformationTransferRate>10000<




ETSI

ETSI TS 101 572-2 V1.2.1 (2014-07)100

Table 6.1.2.1-6: Mapping of ISUP User Service Information into PSTN XML BearerCapability

ITC_value USI Information transfer capability XML InformationTransferCapability VA_01 Speech '00000' VA_02 3,1 kHz audio '10000' VA_03 unrestricted digital information '01000'


TSS reference SIP-I - SIP NNI/Basic call/Sending_of_INVITE/ Selection criteria PICS 6.2.1/5 AND PICS 6.2.1/22 Test Purpose name Mapping of ISUP UTI parameter into PSTN XML BearerCapability Test Purpose Ensure stat on receipt of an INVITE with encapsulated IAM and an User Teleservice

Information parameter is present, a PSTN XML HighLayerCompatibility element is present derived according the HLC_value as indicated in table 6.1.2.1-7

ISUP Parameter values IAM: UTI High Layer Characteristics>HLC_value





Table 6.1.2.1-7: Mapping of User Teleservice Information into PSTN XML HighLayerCharacteristic

HLC_value DSS1 High layer characteristics identification

XML HighLayerCharacteristic

VA_01 Telephony '0000001' VA_02 Facsimile Group 2/3 '0000100' VA_03 Facsimile Group 4 Class I '0100001' VA_04 Facsimile service Group 4, Classes II and III '0100100' VA_05 Syntax based Videotex '0110010' VA_06 International Videotex interworking via

gateways or interworking units '0110011'

VA_07 Telex service '0110101' VA_08 FTAM application '1000010' VA_09 Videotelephony '1100000'

ETSI

ETSI TS 101 572-2 V1.2.1 (2014-07)101


TSS reference SIP-I - SIP NNI/Basic call/Sending_of_INVITE/ Selection criteria PICS 6.2.1/5 Test Purpose name Mapping of Forward call indicator into PSTN XML ProgressIndicator Test Purpose Ensure that on receipt of an INVITE with encapsulated IAM the ISDN User Part indicator

and the ISDN access indicator of the Forward call indicator are mapped into a PSTNXML ProgressIndicator element according the roles PI_value in table 6.1.2.1-8

ISUP Parameter values IAM: Forward call indicator ISDN User Part indicator ISDN access indicator

SIP Parameter values INVITE: PSTM XML MIME body <?xml version="1.0" encoding="utf-8"?> PSTN ProgressIndicator ProgressOctet3 CodingStandard>00< Location>yyyy< ProgressOctet4 ProgressDescription>PI_value<

Comments The Progress indicator value 6 is not specified in Q.931 Message flows SIP–I MGCF SIP NNI



Table 6.1.2.1-8: Mapping of Forward call indicator into PSTN XML ProgressIndicator

PI_value Forward call indicators parameter PSTN XML body with Progress indicator No ISDN User Part

indicator ISDN access

indicator VA_01 0

(ISDN User Part not used all the way)

'0000001' Call is not end-to-end ISDN; further call progress information may be available in-band

VA_02 1 ("ISDN User Part used all the way")

0 ("originating access

non - ISDN")

'0000011' Origination address is non-ISDN

VA_03 1 ("ISDN User Part used all the way")

1 ("originating access

ISDN")

'0000110'

ETSI

ETSI TS 101 572-2 V1.2.1 (2014-07)102


TSS reference SIP-I - SIP NNI/Basic call/Sending_of_INVITE/ Selection criteria PICS 6.2.1/5 Test Purpose name Mapping of Progress Indicator IE into PSTN XML ProgressIndicator Test Purpose Ensure stat on receipt of an INVITE with encapsulated IAM and an ATP parameter is

present containing a Progress Indicator IE a PSTN XML ProgressIndicator element is present derived according the PI_VA as indicated in table 6.1.2.1-9

ISUP Parameter values IAM: ATP Progress Indicator Progress Description=PI_VA

SIP Parameter values INVITE: <?xml version="1.0" encoding="utf-8"?> PSTN ProgressIndicator ProgressOctet3 CodingStandard>00< Location>0000< ProgressOctet4 ProgressDescription>PI_VA<

Comments Message flows SIP-I- MGCF SIP NNI



Table 6.1.2.1-9: Mapping of ISUP ATP Progress Indicator into PSTN XML ProgressIndicator

PI_VA ATP Progress Indicator value XML ProgressIndicator ProgressDescription


'0000001'




ETSI

ETSI TS 101 572-2 V1.2.1 (2014-07)103

TP number TP_201_039 Reference [1], clause 7.3.1 [2], clause 7.2.3.2.2A1.1

TSS reference SIP-I - SIP NNI/Basic call/Sending_of_INVITE/ Selection criteria PICS 6.2.2/1 Test Purpose name Number Portability Separate Directory Number Addressing Method is used Test Purpose Ensure that on receipt of an INVITE with encapsulated IAM and the Called Directory

Number is present Nature of address indicator: "Network routing number in national (significant) number format" or "National (significant) number" or "Network routing number in network specific number format", an INVITE us sent The userpart of the request URI is derived from the Called Directory Number. '+CC' is inserted before the digitstring: • The rn parameter of the request URI is derived from the Called Party Number. '+CC'

is inserted before the digitstring • The npdi URI parameter is added to the request URI The userpart of the To header field is derived from the Called Directory Number. '+CC' is inserted before the digitstring: • The rn parameter of the request URI is derived from the Called Party Number. '+CC'

is inserted before the digitstring • The npdi URI parameter is added to the request URI

ISUP Parameter values IAM: Called party number "National (significant) number" Called Directory Number Nature of address indicator: "Network routing number in national (significant) number format" or "National (significant) number" or "Network routing number in network specific number format"

SIP Parameter values INVITE: Request line <+CC Called Directory Number>; rn= +CC Called party number;npdi To: <+CC Called Directory Number>; rn= +CC Called party number;npdi

Comments Message flows SIP- MGCF SIP NNI



ETSI

ETSI TS 101 572-2 V1.2.1 (2014-07)104


TSS reference SIP-I - SIP NNI/Basic call/Sending_of_INVITE/ Selection criteria PICS 6.2.2/2 Test Purpose name Number Portability Concatenated Addressing Method is used. Test Purpose Ensure that on receipt of an INVITE with encapsulated IAM and the Called Directory

Number is not present, the Nature of address indicator of the Called party number is set to: "Network routing number concatenated with called directory number" or "National (significant) number", an INVITE us sent The userpart of the request URI is derived from the Called Party Number - the prefix representing the Portability routing number is removed. '+CC' is inserted before the digitstring: • The rn parameter of the request URI is derived from the Called Party Number. The

digits follow the prefix representing the Portability Routing Number are removed from the digitstring. '+CC' is inserted before the digitstring

• The npdi URI parameter is added to the request URI The userpart of the To header field is derived from the Called Party Number- the prefix representing the Portability routing number is removed. '+CC' is inserted before the digitstring: • The rn parameter of the request URI is derived from the Called Party Number. The

digits follow the prefix representing the Portability Routing Number are removed from the digitstring. '+CC' is inserted before the digitstring

• The npdi URI parameter is added to the request URI ISUP Parameter values IAM: Called party number

Nature of address indicator: "Network routing number concatenated with called directory number" or "National (significant) number"

SIP Parameter values INVITE: Request line <+CC Called Party Number>; rn= <+CC Portability Routing Number>;npdi To: <+CC Called Party Number>; rn= <+CC Portability Routing Number>;npdi




ETSI

ETSI TS 101 572-2 V1.2.1 (2014-07)105


TSS reference SIP-I - SIP NNI/Basic call/Sending_of_INVITE/ Selection criteria PICS 6.2.2/3 Test Purpose name Number Portability Separate Network Routing Number Addressing Method is used. Test Purpose Ensure that on receipt of an INVITE with encapsulated IAM and the Network Routing

Number is present Nature of address indicator: "Network routing number in national (significant) number format" or "Network routing number in network specific number format", an INVITE us sent The userpart of the request URI is derived from the Called Party Number. '+CC' is inserted before the digitstring: • The rn parameter of the request URI is derived from the Network Routing Number.

'+CC' is inserted before the digitstring • The npdi URI parameter is added to the request URI The userpart of the To header field is derived from the Called Party Number. '+CC' is inserted before the digitstring: • The rn parameter of the request URI is derived from the Network Routing Number.

'+CC' is inserted before the digitstring • The npdi URI parameter is added to the request URI

ISUP Parameter values IAM: Called party number "National (significant) number" Network Routing Number Nature of address indicator: "Network routing number in national (significant) number format" or "National (significant) number" or "Network routing number in network specific number format"

SIP Parameter values INVITE: Request line <+CC Called Party Number>; rn= <+CC Network Routing Number>;npdi To: <+CC Called Party Number>; rn= <+CC Network Routing Number>;npdi




TP number TP_201_042 Reference [1], clause 7.3.1 [2], clause 7.2.3.2.2B.1

TSS reference SIP-I - SIP NNI/Basic call/Sending_of_INVITE/ Selection criteria PICS 6.2.2/5 AND PICS 6.2.2/8 Test Purpose name Mapping of ISUP carrier selection information into 'cic' URI parameter Test Purpose Ensure that on receipt of an IAM and a Transit Network Selection parameter is present, the

value of the Transit Network Selection parameter is sent in the cic URI parameter of the Request URI of the sent INVITE request

ISUP Parameter values IAM: Transit Network Selection SIP Parameter values INVITE: Request URI sip: <called party number;cic=TNS value Comments Message flows SIP-I MGCF SIP NNI




ETSI

ETSI TS 101 572-2 V1.2.1 (2014-07)106

6.1.2.2 Updating Precondition Information

TP number TP_202_001 Reference [1], clause 7.3.4 TSS reference SIP-I - SIP NNI /Basic call/ Updating Precondition Information / Selection criteria PICS 7.2.1/3 Test Purpose name Update received after INVITE was sent Test Purpose For each early SIP dialogue for which a provisional response has been received from the

succeeding node indicating support for preconditions the MGCF, using an UPDATE or a PRACK request, shall send a confirmation that all the required preconditions have been met.

ISUP Parameter values SIP Parameter values Comments Message flows SIP-I MGCF SIP NNI

INVITE (IAM) � � INVITE 100 Trying � � 100 Trying 183 Session Progress � � 183 Session Progress PRACK � � PRACK 200 OK (PRACK) � � 200 OK (PRACK) UPDATE � � UPDATE 200 OK(UPDATE) � � 200 OK(UPDATE)



TSS reference SIP-I - SIP NNI/Basic call/Receipt_of_4xx-5xx-6xx/ Selection criteria Test Purpose name Mapping of unsuccessful final responses to ISUP/BICC Release messages Test Purpose A 580 Precondition failure response has been received from the succeeding IMS node as a

response either to the INVITE request, to the UPDATE request or to the PRACK request. All early dialogues are considered terminated upon reception of the 580 Precondition failure response to the INVITE request. The MGCF shall release the call with REL message with Cause Code '127 Interworking' to be sent to the SIP-I based circuit-switched core network. The MGCF shall encapsulate the REL message into the 480 Temporarily unavailable response and send it to the SIP-I based circuit-switched 3GPP core network.

ISUP Parameter values REL: 127 (interworking unspecified) SIP Parameter values SIP_Response Comments Message flows SIP-I MGCF SIP NNI

INVITE (IAM) � � INVITE 100 Trying � � 100 Trying 183 Session Progress � � 183 Session Progress Case A PRACK � � PRACK 200 OK (PRACK) � � 200 OK (PRACK) 480 Temporarily unavailable (127- interworking unspecified) (REL)

� � 580 Precondition failure

ACK (RLC) � � ACK

Case B PRACK � � PRACK 200 OK (PRACK) � � 200 OK (PRACK) UPDATE � � UPDATE 200 OK(UPDATE) � � 200 OK(UPDATE) 480 Temporarily unavailable (127- interworking unspecified) (REL)

� � 580 Precondition failure

ACK (RLC) � � ACK

ETSI

ETSI TS 101 572-2 V1.2.1 (2014-07)107

6.1.2.3 Sending of ACM and awaiting answer indication


TSS reference SIP-I - SIP NNI/Basic call/Sending_of_18x with encapsulated ACM/ Selection criteria Test Purpose name An ACM is sent after a 180 Ringing was received Test Purpose Ensure that on receipt of a 180 Ringing provisional response without P-Early-Media

header, the SUT sends a 180 Ringing with an encapsulated ACM. The Called party's status indicator is set to 'subscriber free'. The ringing tone is sent by the SUT

ISUP Parameter values ACM: Called party's status indicator =subscriber free SIP Parameter values Comments Message flows SIP-I MGCF SIP NNI

INVITE (IAM) � � INVITE � 100 Trying 180 Ringing (ACM) � � 180 Ringing � Ringing tone



TSS reference SIP-I - SIP NNI/Basic call/Sending_of_18x with encapsulated ACM/ Selection criteria PICS 6.2.1/9 Test Purpose name 180 received, a P-Early-Media header is present Test Purpose Ensure that on receipt of a 180 Ringing provisional response with P-Early-Media header

does not authorize the backward early media, the SUT sends a 180 Ringing with an encapsulated ACM. The Called party's status indicator is set to 'subscriber free'. The ringing tone is sent by the SUT

ISUP Parameter values ACM: Called party's status indicator =subscriber free SIP Parameter values Comments Message flows SIP-I MGCF SIP NNI

INVITE (IAM) � � INVITE 100 Trying � � 100 Trying 180 Ringing (ACM) � � 180 Ringing � Ringing tone



TSS reference SIP-I - SIP NNI/Basic call/Sending_of_18x with encapsulated ACM/ Selection criteria PICS 6.2.1/9 AND PICS 6.2.1/14 Test Purpose name 180 received, a P-Early-Media header not authorize early media is present Test Purpose Ensure that on receipt of a 180 Ringing provisional response with P-Early-Media header

does not authorize the backward early media, the SUT sends a 180 Ringing with an encapsulated ACM. The Called party's status indicator is set to 'subscriber free'. Based on local knowledge that the call is transited to a PSTN network the SUT does not generate the awaiting answer indication.

ISUP Parameter values ACM: Called party's status indicator =subscriber free SIP Parameter values 180

P-Early-Media: inactive 180 (ACM)


INVITE (IAM) � � INVITE � 100 Trying 180 Ringing (ACM - free) � � 180 Ringing � � Early media


ETSI

ETSI TS 101 572-2 V1.2.1 (2014-07)108


TSS reference SIP-I - SIP NNI/Basic call/Sending_of_18x with encapsulated ACM/ Selection criteria PICS 6.2.1/9 Test Purpose name 181 received, a P-Early-Media header authorize early media is present Test Purpose Ensure that on receipt of a 181 Call is Being Forwarded and a P-Early-Media is present

authorizing backward early media, a 181 Call is being forwarded or 183 Session Progress with an encapsulated ACM is sent. The Called party's status indicator is set to 'no indication' and an optional backward call indicator is present, the In-band information indicator is set to 'in-band information or appropriate pattern is now available'. The SUT does not generate the awaiting answer indication

ISUP Parameter values ACM: Called party's status indicator =no indication oBCi = in-band information or appropriate pattern is now available

SIP Parameter values 181 P-Early-Media: sendonly 181/183 (ACM)


INVITE (IAM) � � INVITE � 100 Trying � 181 Call is Being Forwarded CASE A 181 Call is Being Forwarded (ACM no indication)

�

CASE B 183 Session Progress (ACM no indication)

�

� � Early media Apply post test routine


TSS reference SIP-I - SIP NNI/Basic call/Sending_of_18x with encapsulated ACM/ Selection criteria PICS 6.2.1/9 Test Purpose name 183 received, a P-Early-Media header authorize early media is present Test Purpose Ensure that on receipt of a 183 Session Progress and a P-Early-Media header is present

authorizing backward early media, a 183 Session Progress with an encapsulated ACM is sent. The Called party's status indicator is set to 'no indication' and an optional backward call indicator is present, the In-band information indicator is set to 'in-band information or appropriate pattern is now available'. The SUT does not generate the awaiting answer indication

ISUP Parameter values ACM: Called party's status indicator =no indication oBCi = in-band information or appropriate pattern is now available

SIP Parameter values 183 P-Early-Media: sendonly 183 (ACM)


INVITE (IAM) � � INVITE � 100 Trying 183 Session Progress (ACM no indication)

� � 183 Session Progress

� � Early media Apply post test routine

ETSI

ETSI TS 101 572-2 V1.2.1 (2014-07)109


TSS reference SIP-I - SIP NNI/Basic call/Sending_of_18x with encapsulated ACM/ Selection criteria PICS 6.2.1/15 Test Purpose name MGW plays out early media associated with the Alert-Info header Test Purpose Ensure that the MGW plays a early media associated with the URL in an Alert-Info header

contained in a received 180 Ringing response ISUP Parameter values SIP Parameter values 180: Alert-Info: < Media resource URL> Comments Message flows SIP-I MGCF SIP NNI

INVITE (IAM) � � INVITE � 100 Trying 180 Ringing (ACM free) � � 180 Ringing



TSS reference SIP-I - SIP NNI/Basic call/Sending_of_18x with encapsulated ACM/ Selection criteria PICS 6.2.1/9 AND PICS 6.2.1/16 Test Purpose name The SUT initiates the sending of awaiting answer indication Test Purpose Ensure that the SUT initiates the sending of awaiting answer indication as indicated in a

P-Early-Media received in a 183 Session Progress and the P-Early-Media header authorizes backward early media

ISUP Parameter values SIP Parameter values 183: P-Early-Media: sendonly Comments Message flows SIP-I MGCF SIP NNI

INVITE (IAM) � � INVITE � 100 Trying 183 Session Progress (ACM) � � 183 Session Progress � � Early media



TSS reference SIP-I - SIP NNI/Basic call/Sending_of_18x with encapsulated ACM/ Selection criteria Test Purpose name 180 received, coding of Backward call indicator in ACM TMR speech or 3,1 kHz audio Test Purpose INVITE with encapsulated IAM with Transmission Medium Requirement indicator=speech

or 3,1 kHz received. Ensure that on receipt of a 180 Ringing response, a 183 Session Progress with an encapsulated ACM is sent and the Backward call indicator is set to the following values: • Charge indicator = charge (10) • Called party's status indicator = subscriber free (01) • Called party's category indicator = no indication (00) • End-to-end method indicator = no end-to-end method available (00) • Interworking indicator = interworking encountered (1) • End-to-end information indicator = no end-to-end information available (0) • ISDN user part/BICC indicator = ISDN user part not used all the way (0) • ISDN access indicator = terminating access non-ISDN (0) • Echo control device indicator = incoming echo control device included (1)

ISUP Parameter values IAM: Transmission Medium Requirement indicator=speech or 3,1 kHz SIP Parameter values Comments Message flows SIP-I MGCF SIP NNI

INVITE (IAM) � � INVITE � 100 Trying 180 Ringing (ACM) � � 180 Ringing


ETSI

ETSI TS 101 572-2 V1.2.1 (2014-07)110


TSS reference SIP-I - SIP NNI/Basic call/Sending_of_18x with encapsulated ACM/ Selection criteria Test Purpose name 181 received, coding of Backward call indicator in ACM TMR speech or 3,1 kHz audio Test Purpose INVITE with encapsulated IAM with Transmission Medium Requirement indicator=speech

or 3,1 kHz received. Ensure that on receipt of a 181 Call is Being forwarded response, a 181 Being Forwarded or 183 Session Progress with encapsulated ACM is sent and the Backward call indicator is set to the following values: • Charge indicator = charge (10) • Called party's status indicator = no indication (00) • Called party's category indicator = no indication (00) • End-to-end method indicator = no end-to-end method available (00) • Interworking indicator = interworking encountered (1) • End-to-end information indicator = no end-to-end information available (0) • ISDN user part/BICC indicator = ISDN user part not used all the way (0) • ISDN access indicator = terminating access non-ISDN (0) • Echo control device indicator = incoming echo control device included (1)

ISUP Parameter values IAM: Transmission Medium Requirement indicator=speech or 3,1 kHz SIP Parameter values 181/183 (ACM):

Backward call indicator Comments Message flows SIP-I MGCF SIP NNI

INVITE (IAM) � � INVITE � 100 Trying � 181 Call is Being forwarded CASE A 181 Call is Being forwarded (ACM) � CASE B 183 Session Progress (ACM) �



TSS reference SIP-I - SIP NNI/Basic call/Sending_of_18x with encapsulated ACM/ Selection criteria PICS 6.2.1/9 AND NOT PICS 6.2.1/18 Test Purpose name 183 received, coding of Backward call indicator in ACM TMR speech or 3,1 kHz audio Test Purpose INVITE with encapsulated IAM with Transmission Medium Requirement indicator=speech

or 3,1 kHz received. Ensure that on receipt of a 183 Session Progress response with P-Early-Media header, a 183 Session Progress with an encapsulated ACM is sent and the Backward call indicator is set to the following values: • Charge indicator = charge (10) • Called party's status indicator = no indication (00) • Called party's category indicator = no indication (00) • End-to-end method indicator = no end-to-end method available (00) • Interworking indicator = interworking encountered (1) • End-to-end information indicator = no end-to-end information available (0) • ISDN user part/BICC indicator = ISDN user part not used all the way (0) • ISDN access indicator = terminating access non-ISDN (0) • Echo control device indicator = incoming echo control device included (1)

ISUP Parameter values IAM: Transmission Medium Requirement indicator=speech or 3,1 kHz SIP Parameter values 183: P-Early-Media: sendonly

183 (ACM) Comments Message flows SIP-I MGCF SIP NNI

INVITE (IAM) � � INVITE � 100 Trying 183 Session Progress (ACM)



ETSI

ETSI TS 101 572-2 V1.2.1 (2014-07)111


TSS reference SIP-I - SIP NNI/Basic call/Sending_of_18x with encapsulated ACM/ Selection criteria PICS 6.2.4/2 AND NOT PICS 6.2.1/18 Test Purpose name 180 received, coding of Backward call indicator in ACM TMR 64 kBit/s unrestricted Test Purpose INVITE with encapsulated IAM with Transmission Medium Requirement indicator=64 kBit/s

unrestricted received. Ensure that on receipt of a 180 Ringing response, a 180 Ringing with an encapsulated ACM is sent and the Backward call indicator is set to the following values: • Charge indicator = charge (10) • Called party's status indicator = subscriber free (01) • Called party's category indicator = no indication (00) • End-to-end method indicator = no end-to-end method available (00) • Interworking indicator = interworking encountered (1) • End-to-end information indicator = no end-to-end information available (0) • ISDN user part/BICC indicator = ISDN user part not used all the way (0) • ISDN access indicator = terminating access non-ISDN (0) • Echo control device indicator = incoming echo control device not included (0)

ISUP Parameter values IAM: Transmission Medium Requirement indicator=64 kBit/s unrestricted SIP Parameter values Comments Message flows SIP-I MGCF SIP NNI




TSS reference SIP-I - SIP NNI/Basic call/Sending_of_18x with encapsulated ACM/ Selection criteria PICS 6.2.4/2 AND NOT PICS 6.2.1/18 Test Purpose name 181 received, coding of Backward call indicator in ACM TMR 64 kBit/s unrestricted Test Purpose INVITE with encapsulated IAM with Transmission Medium Requirement indicator=64 kBit/s

unrestricted received. Ensure that on receipt of a 181 Call is Being forwarded response, a 181 Being Forwarded or 183 Session Progress with encapsulated ACM is sent and the Backward call indicator is set to the following values: • Charge indicator = charge (10) • Called party's status indicator = no indication (00) • Called party's category indicator = no indication (00) • End-to-end method indicator = no end-to-end method available (00) • Interworking indicator = interworking encountered (1) • End-to-end information indicator = no end-to-end information available (0) • ISDN user part/BICC indicator = ISDN user part not used all the way (0) • ISDN access indicator = terminating access non-ISDN (0) • Echo control device indicator = incoming echo control device not included (0)

ISUP Parameter values IAM: Transmission Medium Requirement indicator=64 kBit/s unrestricted SIP Parameter values 181/183 (ACM):


IAM � � INVITE � 100 Trying � 181 Call is Being forwarded CASE A 181 Call is Being forwarded (ACM) � CASE B 183 Session Progress (ACM) �


ETSI

ETSI TS 101 572-2 V1.2.1 (2014-07)112


TSS reference SIP-I - SIP NNI/Basic call/Sending_of_18x with encapsulated ACM/ Selection criteria PICS 6.2.4/2 AND NOT PICS 6.2.1/18 AND PICS 6.2.1/9 Test Purpose name 183 received, coding of Backward call indicator in ACM TMR 64 kBit/s unrestricted Test Purpose INVITE with encapsulated IAM with Transmission Medium Requirement indicator=64 kBit/s

unrestricted received. Ensure that on receipt of a 183 Session Progress response, a 183 Session Progress with an encapsulated ACM is sent and the Backward call indicator is set to the following values: • Charge indicator = charge (10) • Called party's status indicator = no indication (00) • Called party's category indicator = no indication (00) • End-to-end method indicator = no end-to-end method available (00) • Interworking indicator = interworking encountered (1) • End-to-end information indicator = no end-to-end information available (0) • ISDN user part/BICC indicator = ISDN user part not used all the way (0) • ISDN access indicator = terminating access non-ISDN (0) • Echo control device indicator = incoming echo control device not included (0)

ISUP Parameter values IAM: Transmission Medium Requirement indicator=64 kBit/s unrestricted SIP Parameter values 183: P-Early-Media: sendonly






TSS reference SIP-I - SIP NNI/Basic call/Sending_of_18x with encapsulated ACM/ Selection criteria PICS 6.2.4/2 AND PICS 6.2.1/18 Test Purpose name 180 received, coding of Backward call indicator in ACM TMR 64 kBit/s unrestricted Test Purpose INVITE with encapsulated IAM with Transmission Medium Requirement indicator=64 kBit/s

unrestricted received. Ensure that on receipt of a 180 Ringing response, a 180 Ringing with an encapsulated ACM is sent and the Backward call indicator is set to the following values: • Charge indicator = charge (10) • Called party's status indicator = subscriber free (01) • Called party's category indicator = no indication (00) • End-to-end method indicator = no end-to-end method available (00) • Interworking indicator = no interworking encountered (0) • End-to-end information indicator = no end-to-end information available (0) • ISDN user part/BICC indicator = ISDN user part used all the way (1) • ISDN access indicator = terminating access ISDN (1) • Echo control device indicator = incoming echo control device not included (0)

ISUP Parameter values IAM: Transmission Medium Requirement indicator=64 kBit/s unrestricted SIP Parameter values Comments Message flows SIP-I MGCF SIP NNI



ETSI

ETSI TS 101 572-2 V1.2.1 (2014-07)113


TSS reference SIP-I - SIP NNI/Basic call/Sending_of_18x with encapsulated ACM/ Selection criteria PICS 6.2.4/2 AND PICS 6.2.1/18 Test Purpose name 181 received, coding of Backward call indicator in ACM TMR 64 kBit/s unrestricted Test Purpose INVITE with encapsulated IAM with Transmission Medium Requirement indicator=64 kBit/s

unrestricted received. Ensure that on receipt of a 181 Call is Being forwarded response, a 181 Being Forwarded or 183 Session Progress with encapsulated ACM is sent and the Backward call indicator is set to the following values: • Charge indicator = charge (10) • Called party's status indicator = no indication (00) • Called party's category indicator = no indication (00) • End-to-end method indicator = no end-to-end method available (00) • Interworking indicator = no interworking encountered (0) • End-to-end information indicator = no end-to-end information available (0) • ISDN user part/BICC indicator = ISDN user part used all the way (1) • ISDN access indicator = terminating access ISDN (1) • Echo control device indicator = incoming echo control device not included (0)

ISUP Parameter values IAM: Transmission Medium Requirement indicator=64 kBit/s unrestricted SIP Parameter values 181/183 (ACM):





TSS reference SIP-I - SIP NNI/Basic call/Sending_of_18x with encapsulated ACM/ Selection criteria PICS 6.2.4/2 AND PICS 6.2.1/18 AND PICS 6.2.1/9 Test Purpose name 183 received, coding of Backward call indicator in ACM TMR 64 kBit/s unrestricted Test Purpose INVITE with encapsulated IAM with Transmission Medium Requirement indicator=64 kBit/s

unrestricted received. Ensure that on receipt of a 183 Session Progress response, a 183 Session Progress with an encapsulated ACM is sent and the Backward call indicator is set to the following values: • Charge indicator = charge (10) • Called party's status indicator = no indication (00) • Called party's category indicator = no indication (00) • End-to-end method indicator = no end-to-end method available (00) • Interworking indicator = no interworking encountered (0) • End-to-end information indicator = no end-to-end information available (0) • ISDN user part/BICC indicator = ISDN user part used all the way (1) • ISDN access indicator = terminating access ISDN (1) • Echo control device indicator = incoming echo control device not included (0)

ISUP Parameter values IAM: Transmission Medium Requirement indicator=64 kBit/s unrestricted SIP Parameter values 183: P-Early-Media: sendonly


INVITE (IAM) � � INVITE � 100 Trying 183 Session Progress (ACM) � � 183 Session Progress


ETSI

ETSI TS 101 572-2 V1.2.1 (2014-07)114


TSS reference SIP-I - SIP NNI/Basic call/Sending_of_18x with encapsulated ACM/ Selection criteria Test Purpose name 180 received, coding of Backward call indicator in ACM HLC "Facsimile Group 2/3". Test Purpose INVITE with encapsulated IAM with Transmission Medium Requirement indicator=3,1 kHz

and High Layer Compatibility= Facsimile Group 2/3 received. Ensure that on receipt of a 180 Ringing response, a 180 Ringing with an encapsulated ACM is sent and the Backward call indicator is set to the following values: • Charge indicator = charge (10) • Called party's status indicator = subscriber free (01) • Called party's category indicator = no indication (00) • End-to-end method indicator = no end-to-end method available (00) • Interworking indicator = interworking encountered (1) • End-to-end information indicator = no end-to-end information available (0) • ISDN user part/BICC indicator = ISDN user part not used all the way (0) • ISDN access indicator = terminating access non-ISDN (0) • Echo control device indicator = incoming echo control device not included (0)

ISUP Parameter values IAM: Transmission Medium Requirement indicator=3,1 kHz High Layer Compatibility= Facsimile Group 2/3

SIP Parameter values Comments Message flows SIP-I MGCF ISUP




TSS reference SIP-I - SIP NNI/Basic call/Sending_of_18x with encapsulated ACM/ Selection criteria Test Purpose name 181 received, coding of Backward call indicator in ACM HLC "Facsimile Group 2/3". Test Purpose INVITE with encapsulated IAM with Transmission Medium Requirement indicator=3,1 kHz

and High Layer Compatibility= Facsimile Group 2/3 received. Ensure that on receipt of a 181 Call is Being forwarded response, a 181 Being Forwarded or 183 Session Progress with encapsulated ACM is sent and the Backward call indicator is set to the following values: • Charge indicator = charge (10) • Called party's status indicator = no indication (00) • Called party's category indicator = no indication (00) • End-to-end method indicator = no end-to-end method available (00) • Interworking indicator = interworking encountered (1) • End-to-end information indicator = no end-to-end information available (0) • ISDN user part/BICC indicator = ISDN user part not used all the way (0) • ISDN access indicator = terminating access non-ISDN (0) • Echo control device indicator = incoming echo control device not included (0)


SIP Parameter values 181/183 (ACM): Backward call indicator




ETSI

ETSI TS 101 572-2 V1.2.1 (2014-07)115


TSS reference SIP-I - SIP NNI/Basic call/Sending_of_18x with encapsulated ACM/ Selection criteria PICS 6.2.1/9 Test Purpose name 183 received, coding of Backward call indicator in ACM HLC "Facsimile Group 2/3". Test Purpose INVITE with encapsulated IAM with Transmission Medium Requirement indicator=3,1 kHz

and High Layer Compatibility= Facsimile Group 2/3 received. Ensure that on receipt of a 183 Session Progress response, a 183 Session Progress with an encapsulated ACM is sent and the Backward call indicator is set to the following values: • Charge indicator = charge (10) • Called party's status indicator = no indication (00) • Called party's category indicator = no indication (00) • End-to-end method indicator = no end-to-end method available (00) • Interworking indicator = interworking encountered (1) • End-to-end information indicator = no end-to-end information available (0) • ISDN user part/BICC indicator = ISDN user part not used all the way (0) • ISDN access indicator = terminating access non-ISDN (0) • Echo control device indicator = incoming echo control device not included (0)


SIP Parameter values Comments Message flows SIP-I MGCF SIP NNI




TSS reference SIP-I - SIP NNI/Basic call/Sending_of_18x with encapsulated ACM/ Selection criteria PICS 6.2.1/5 Test Purpose name Mapping of PSTN XML ProgressIndicator 1 into Backward call indicator in ACM Test Purpose Ensure that on receipt of a 180 Ringing and the PSTN XML ProgressIndicator is present,

the value 1 is mapped into the Backward call indicator present in the encapsulated ACM: ISDN User Part indicator • ISDN User Part not used all the way (0)

ISUP Parameter values ACM: ISDN User Part indicator ISDN User Part not used all the way

SIP Parameter values 180: <?xml version="1.0" encoding="utf-8"?> PSTN ProgressIndicator ProgressOctet4 ProgressDescription>0000001<

Comments Progress Information: 'Call is not end-to-end ISDN: further call progress information may be available in-band'

Message flows SIP-I MGCF SIP NNI INVITE (IAM) � � INVITE � 100 Trying 180 Ringing (ACM) � � 180 Ringing


ETSI

ETSI TS 101 572-2 V1.2.1 (2014-07)116


TSS reference SIP-I - SIP NNI/Basic call/Sending_of_18x with encapsulated ACM/ Selection criteria PICS 6.2.1/5 Test Purpose name Mapping of PSTN XML ProgressIndicator 2 in 180 into Backward call indicator in ACM Test Purpose Ensure that on receipt of a 180 Ringing and the PSTN XML ProgressIndicator is present,

the value 2 is mapped into the Backward call indicator present in the encapsulated ACM: ISDN User Part indicator

• ISDN User Part used all the way (1) ISDN access indicator

• Terminating access non-ISDN (0) ISUP Parameter values ACM: ISDN User Part indicator

ISDN User Part used all the way ISDN access indicator Terminating access non-ISDN


Comments Progress Information: 'Destination address is non-ISDN' Message flows SIP-I MGCF SIP NNI




TSS reference SIP-I - SIP NNI/Basic call/Sending_of_18x with encapsulated ACM/ Selection criteria PICS 6.2.1/5 Test Purpose name Mapping of PSTN XML ProgressIndicator 7 in 180 into Backward call indicator in ACM Test Purpose Ensure that on receipt of a 180 Ringing and the PSTN XML ProgressIndicator is present,

the value 7 is mapped into the Backward call indicator present in the encapsulated ACM: ISDN User Part indicator


• Terminating access ISDN (1) Interworking indicator

• no interworking encountered (0) ISUP Parameter values ACM: ISDN User Part indicator

ISDN User Part used all the way ISDN access indicator Terminating access ISDN Interworking indicator no interworking encountered


Comments Progress Information: value not specified. Meaning 'terminating user is ISDN' Message flows SIP-I MGCF SIP NNI



ETSI

ETSI TS 101 572-2 V1.2.1 (2014-07)117


TSS reference SIP-I - SIP NNI/Basic call/Sending_of_18x with encapsulated ACM/ Selection criteria PICS 6.2.1/5 Test Purpose name Mapping of PSTN XML ProgressIndicator 8 in 180 into optional Backward call indicator in

ACM Test Purpose Ensure that on receipt of a 180 Ringing and the PSTN XML ProgressIndicator is present,

the value 8 is mapped into the Optional backward call indicator present in the encapsulated ACM:

Optional backward call indicators In-band information indicator

• in-band information or an appropriate pattern is now available ISUP Parameter values ACM: Optional backward call indicators

In-band information indicator in-band information or an appropriate pattern is now available


Comments Progress Information 'In-band information or an appropriate pattern is now available' Message flows SIP-I MGCF SIP NNI




TSS reference SIP-I - SIP NNI/Basic call/Sending_of_18x with encapsulated ACM/ Selection criteria PICS 6.2.1/5 AND PICS 6.2.1/9 Test Purpose name Mapping of PSTN XML ProgressIndicator 1 in 183 into Backward call indicator in ACM Test Purpose Ensure that on receipt of a 183 Session Progress and the PSTN XML ProgressIndicator is

present, the value 1 is mapped into the Backward call indicator present in the encapsulated ACM: ISDN User Part indicator • ISDN User Part not used all the way (0)

ISUP Parameter values ACM: ISDN User Part indicator ISDN User Part not used all the way

SIP Parameter values 183: P-Early-Media: sendonly <?xml version="1.0" encoding="utf-8"?> PSTN ProgressIndicator ProgressOctet4 ProgressDescription>0000001<


Message flows SIP-I MGCF SIP NNI INVITE (IAM) � � INVITE � 100 Trying 183 Session Progress (ACM) � � 183 Session Progress


ETSI

ETSI TS 101 572-2 V1.2.1 (2014-07)118



present, the value 2 is mapped into the Backward call indicator present in the encapsulated ACM: ISDN User Part indicator


• Terminating access non-ISDN (0) ISUP Parameter values ACM: ISDN User Part indicator

ISDN User Part used all the way ISDN access indicator Terminating access non-ISDN







present, the value 7 is mapped into the Backward call indicator present in the encapsulated ACM: ISDN User Part indicator


• Terminating access ISDN (1) Interworking indicator

• no interworking encountered (0) ISUP Parameter values ACM: ISDN User Part indicator

ISDN User Part used all the way ISDN access indicator Terminating access non-ISDN Interworking indicator no interworking encountered





ETSI

ETSI TS 101 572-2 V1.2.1 (2014-07)119



present, the value 8 is mapped into the Optional backward call indicator present in the encapsulated ACM:









TSS reference SIP-I - SIP NNI/Basic call/Sending_of_18x with encapsulated ACM/ Selection criteria PICS 6.2.1/9 Test Purpose name Mapping of P-Early-Media header in 183 into Optional backward call indicator in ACM Test Purpose Ensure that on receipt of a 183 Session Progress and the P-Early-Media header

authorizing backward early media is mapped into the Backward call indicator present in the encapsulated ACM:




SIP Parameter values 183: P-Early-Media: sendonly Comments Progress Information 'In-band information or an appropriate pattern is now available' Message flows SIP-I MGCF SIP NNI



ETSI

ETSI TS 101 572-2 V1.2.1 (2014-07)120


TSS reference SIP-I - SIP NNI/Basic call/Sending_of_18x with encapsulated ACM/ Selection criteria PICS 6.2.1/9 Test Purpose name Mapping of P-Early-Media header in 181 into Optional backward call indicator in ACM Test Purpose Ensure that on receipt of a 181 Call is Being Forwarded and the P-Early-Media authorizing

backward early media is mapped into the Backward call indicator present in the encapsulated ACM:




SIP Parameter values 183: P-Early-Media: sendonly Comments Progress Information 'In-band information or an appropriate pattern is now available' Message flows SIP-I MGCF SIP NNI

INVITE (IAM) � � INVITE � 100 Trying 181 Call is Being Forwarded (ACM)

� � 181 Call is Being Forwarded



TSS reference SIP-I - SIP NNI/Basic call/Sending_of_18x with encapsulated ACM/ Selection criteria PICS 6.2.1/5 Test Purpose name Mapping of PSTN XML ProgressIndicator 1 in 180 into the Access Transport Parameter Test Purpose Ensure that on receipt of a 180 Ringing and the PSTN XML ProgressIndicator is present,

the value 1 is mapped into the Access Transport Parameter containing the Progress Indicator value 1 in the ACM: Access Transport Parameter

Progress Indicator • Progress Description='0000001'

ISUP Parameter values ACM: Access Transport Progress Indicator Progress Description='0000001'



Message flows SIP-I MGCF SIP NNI INVITE (IAM) � � INVITE � 100 Trying 180 Ringing (ACM) � � 180 Ringing


ETSI

ETSI TS 101 572-2 V1.2.1 (2014-07)121



the value 2 is mapped into the Access Transport Parameter containing the Progress Indicator value 2 in the encapsulated ACM: Access Transport Parameter








TSS reference SIP-I - SIP NNI/Basic call/Sending_of_18x with encapsulated ACM/ Selection criteria PICS 6.2.1/5 Test Purpose name PSTN XML ProgressIndicator 7 in 180 is not mapped into the Access Transport Parameter Test Purpose Ensure that on receipt of a 180 Ringing and the PSTN XML ProgressIndicator is present,

the value 7 is not mapped into the Access Transport Parameter in the encapsulated ACM ISUP Parameter values ACM: No Access Transport Parameter present SIP Parameter values 180:

<?xml version="1.0" encoding="utf-8"?> PSTN ProgressIndicator ProgressOctet4 ProgressDescription>0000111<




ETSI

ETSI TS 101 572-2 V1.2.1 (2014-07)122



the value 8 is mapped into the Access Transport Parameter containing the Progress Indicator value 8 in the encapsulated ACM: Access Transport Parameter








TSS reference SIP-I - SIP NNI/Basic call/Sending_of_18x with encapsulated ACM/ Selection criteria PICS 6.2.1/5 AND PICS 6.2.1/9 Test Purpose name Mapping of PSTN XML ProgressIndicator 1 in 183 into the Access Transport Parameter Test Purpose Ensure that on receipt of a 183 Session Progress and the P-Early-Media header and PSTN

XML ProgressIndicator is present, the value 1 is mapped into the Access Transport Parameter containing the Progress Indicator value 1 in the encapsulated ACM: Access Transport Parameter





Message flows SIP-I MGCF SIP NNI INVITE (IAM) � � INVITE � 100 Trying 183 Session Progress (ACM)



ETSI

ETSI TS 101 572-2 V1.2.1 (2014-07)123












TSS reference SIP-I - SIP NNI/Basic call/Sending_of_18x with encapsulated ACM/ Selection criteria PICS 6.2.1/5 AND PICS 6.2.1/9 Test Purpose name PSTN XML ProgressIndicator 7 in 183 is not mapped into the Access Transport Parameter Test Purpose Ensure that on receipt of a 183 Session Progress and the PSTN XML ProgressIndicator is

present, the value 7 is not mapped into the Access Transport Parameter in the encapsulated ACM

ISUP Parameter values ACM: No Access Transport Parameter present SIP Parameter values 183: P-Early-Media: sendonly





ETSI

ETSI TS 101 572-2 V1.2.1 (2014-07)124










6.1.2.4 Sending of the Call Progress message (CPG)


TSS reference SIP-I - SIP NNI/Basic call/Sending_of_CPG in encapsulated 18x message/ Selection criteria PICS 6.2.1/9 Test Purpose name 181 received, CPG is sent Test Purpose Ensure that on receipt of a 181 Call is Being Forwarded a 181 Call is Being Forwarded with

encapsulated PG is sent. The Event information parameter in the CPG is set to 'progress' ISUP Parameter values CPG: Event indication=progress SIP Parameter values 181: P-Early-Media: sendonly Comments Message flows SIP-I MGCF SIP NNI

INVITE (IAM) � � INVITE 180 Ringing (ACM) � � 180 Ringing 181 Call is Being Forwarded (CPG)

� � 181 Call is Being Forwarded

early media early media Apply post test routine

ETSI

ETSI TS 101 572-2 V1.2.1 (2014-07)125


TSS reference SIP-I - SIP NNI/Basic call/Sending_of_CPG in encapsulated 18x message/ Selection criteria PICS 6.2.1/9 Test Purpose name Early media is not authorized if no P-Early-Media header is present in the 180 Test Purpose Ensure that on receipt of a 180 Ringing a 180 Ringing with an encapsulated CPG is sent. If

the 180 Ringing contains a P-Early-Media header not authorizing early media, the SUT initiates sending of awaiting answer indication

ISUP Parameter values SIP Parameter values 183: P-Early-Media header present

180: P-Early-Media: inactive Comments Message flows SIP-I MGCF SIP NNI

INVITE (IAM) � � INVITE 183 Session Progress (ACM)


180 Ringing CPG

� � 180 Ringing

ringing tone Apply post test routine


TSS reference SIP-I - SIP NNI/Basic call/Sending_of_CPG in encapsulated 18x message/ Selection criteria PICS 6.2.1/9 Test Purpose name Early media is not authorized if P-Early-Media header does not authorize early media in the

180 Test Purpose Ensure that on receipt of a 180 Ringing a 180 Ringing with an encapsulated CPG is sent. If

the 180 Ringing contains a P-Early-Media header not authorizing early media, the SUT initiates sending of awaiting answer indication

ISUP Parameter values SIP Parameter values 180: P-Early-Media: inactive Comments Message flows SIP-I MGCF SIP NNI



180 Ringing (CPG) � � 180 Ringing ringing tone



TSS reference SIP-I - SIP NNI/Basic call/Sending_of_CPG in encapsulated 18x message/ Selection criteria PICS 6.2.1/9 Test Purpose name Early media is authorized if P-Early-Media header authorize early media in the 180 Test Purpose Ensure that on receipt of a 180 Ringing a 180 Ringing with an encapsulated CPG is sent. If

the 180 Ringing contains a P-Early-Media header authorizing early media, the SUT terminates sending of awaiting answer indication and connects through the early media in backward direction


INVITZE (IAM) � � INVITE 183 Session Progress (ACM)


180 Ringing (CPG) � � 180 Ringing early media early media


ETSI

ETSI TS 101 572-2 V1.2.1 (2014-07)126


TSS reference SIP-I - SIP NNI/Basic call/Sending_of_CPG in encapsulated 18x message/ Selection criteria PICS 6.2.1/14 Test Purpose name The SUT has the knowledge that the call is transited to a PSTN network, the awaiting

answer indication is not generated Test Purpose Ensure that the SUT does not generate the awaiting answer indication if it has the local

knowledge that the call is transited to a PSTN network and the early media is not authorized




180 Ringing (CPG) � � 180 Ringing early media early media



TSS reference SIP-I - SIP NNI/Basic call/Sending_of_CPG in encapsulated 18x message/ Selection criteria PICS 6.2.1/9 Test Purpose name Early media is authorized if P-Early-Media header authorize early media in the 183 Test Purpose Ensure that on receipt of a 183 Session Progress a 183 Session Progress with an

encapsulated CPG is sent. If the 183 Session Progress contains a P-Early-Media header authorizing early media, the SUT terminates sending of awaiting answer indication and connects through the early media in backward direction


INVITE (IAM) � � INVITE 180 Ringing (ACM – free)

� � 180 Ringing

183 Session Progress (CPG)



ETSI

ETSI TS 101 572-2 V1.2.1 (2014-07)127


TSS reference SIP-I - SIP NNI/Basic call/Sending_of_CPG in encapsulated 18x message/ Selection criteria PICS 6.2.1/9 Test Purpose name Early media is authorized if P-Early-Media header authorize early media in the 181 Test Purpose Ensure that on receipt of a 181 Call is Being Forwarded a 181 Call is Being Forwarded with

encapsulated CPG is sent. If the 181 Call is Being Forwarded contains a P-Early-Media header authorizing early media, the SUT terminates sending of awaiting answer indication and connects through the early media in backward direction


INVITE (IAM) � � INVITE 180 Ringing (ACM) � � 180 Ringing CASE A � 181 Call is Being Forwarded 183 Session Progress (CPG) CASE B 181 Call is Being Forwarded (CPG)

�



TSS reference SIP-I - SIP NNI/Basic call/Sending_of_CPG in encapsulated 18x message/ Selection criteria PICS 6.2.1/9 Test Purpose name The SUT change the authorization of early media as indicated in the P-Early-Media

received in 180 Test Purpose Ensure that the SUT terminates the sending of awaiting answer indication and connect

through early media if the P-Early-Media header indicates authorization in the received 180 Ringing response and early media was not authorized before

ISUP Parameter values SIP Parameter values 183: P-Early-Media: inactive

180: P-Early-Media: sendonly Comments Message flows SIP-I MGCF SIP NN

INVITE(IAM) � � INVITE 183 Session Progress(ACM) � � 183 Session Progress

ringing tone 180 Ringing(CPG) � � 180 Ringing early media early media


ETSI

ETSI TS 101 572-2 V1.2.1 (2014-07)128


TSS reference SIP-I - SIP NNI/Basic call/Sending_of_CPG in encapsulated 18x message/ Selection criteria PICS 6.2.1/9 Test Purpose name The SUT change the authorization of early media as indicated in the P-Early-Media

received in 180 Test Purpose Ensure that the SUT initiates the sending of awaiting answer indication and removes

authorization of early media if the P-Early-Media header indicates no authorization of early media received in the 180 Ringing and early media was authorized before

ISUP Parameter values SIP Parameter values 183: P-Early-Media: sendonly

180: P-Early-Media: inactive Comments Message flows SIP-I MGCF SIP NNI

INVITE (IAM) � � INVITE 183 Session Progress (ACM – no indication)


early media early media 180 Ringing (CPG) � � 180 Ringing

ringing tone Apply post test routine


TSS reference SIP-I - SIP NNI/Basic call/Sending_of_CPG in encapsulated 18x message/ Selection criteria PICS 6.2.1/5 AND PICS 6.2.1/9 Test Purpose name Mapping of PSTN XML ProgressIndicator 1 in 183 into ATP in the CPG Test Purpose Ensure that on receipt of a PSTN XML ProgressIndicator value 1 in a 183 Session

Progress, a 183 Session Progress with encapsulated CPG is sent and an Access Transport Parameter is present containing a Progress Indicator #1

ISUP Parameter values CPG: Access Transport Progress Indicator Progress Description='0000001'



INVITE (IAM) � � INVITE 180 Ringing (ACM) � � 180 Ringing 183 Session Progress (CPG)



ETSI

ETSI TS 101 572-2 V1.2.1 (2014-07)129














SIP Parameter values 180: <?xml version="1.0" encoding="utf-8"?> PSTN ProgressIndicator ProgressOctet4 ProgressDescription>0000001< or ProgressDescription>0000010< 183: P-Early-Media: sendonly <?xml version="1.0" encoding="utf-8"?> PSTN ProgressIndicator ProgressOctet4 ProgressDescription>0000100<





ETSI

ETSI TS 101 572-2 V1.2.1 (2014-07)130


TSS reference SIP-I - SIP NNI/Basic call/Sending_of_CPG in encapsulated 18x message/ Selection criteria PICS 6.2.1/5 AND PICS 6.2.1/9 Test Purpose name No mapping of PSTN XML ProgressIndicator 7 in 183 into ATP in the CPG Test Purpose Ensure that on receipt of a PSTN XML ProgressIndicator value 7 in a 183 Session

Progress, a CPG is sent and no Access Transport Parameter is present containing a Progress Indicator #7

ISUP Parameter values CPG: Access Transport not present SIP Parameter values 180:

<?xml version="1.0" encoding="utf-8"?> PSTN ProgressIndicator ProgressOctet4 ProgressDescription>0000001< or ProgressDescription>0000010< 183: P-Early-Media: sendonly <?xml version="1.0" encoding="utf-8"?> PSTN ProgressIndicator ProgressOctet4 ProgressDescription>0000111<



� � 180 Ringing





TSS reference SIP-I - SIP NNI/Basic call/Sending_of_CPG in encapsulated 18x message/ Selection criteria PICS 6.2.1/5 AND PICS 6.2.1/9 Test Purpose name Mapping of PSTN XML ProgressIndicator 8 in 183 into Event information in the CPG Test Purpose Ensure that on receipt of a PSTN XML ProgressIndicator value 8 in a 183 Session

Progress, a 183 Session Progress with encapsulated CPG is sent and Event information parameter is set to 'In-band information or appropriate pattern is now available'

ISUP Parameter values CPG: Event information= In-band information or appropriate pattern is now available SIP Parameter values 183: P-Early-Media: sendonly






ETSI

ETSI TS 101 572-2 V1.2.1 (2014-07)131


TSS reference SIP-I - SIP NNI/Basic call/Sending_of_CPG in encapsulated 18x message/ Selection criteria PICS 6.2.1/5 AND PICS 6.2.1/9 Test Purpose name Mapping of PSTN XML ProgressIndicator 1 in 180 into ATP in the CPG Test Purpose Ensure that on receipt of a PSTN XML ProgressIndicator value 1 in a 180 Ringing, a 180

Ringing with encapsulated CPG is sent and an Access Transport Parameter is present containing a Progress Indicator #1



Comments Message flows SIP NNI MGCF SIP NNI

INVITE (IAM) � Ti/w1 started 183 Session Progress (ACM – no indication)

� Ti/w1 expired �

INVITE

180 Ringing (CPG) � � 180 Ringing



TSS reference SIP-I - SIP NNI/Basic call/Sending_of_CPG in encapsulated 18x message/ Selection criteria PICS 6.2.1/5 Test Purpose name Mapping of PSTN XML ProgressIndicator 2 in 180 into ATP in the CPG Test Purpose Ensure that on receipt of a PSTN XML ProgressIndicator value 2 in a 180 Ringing, a 180





INVITE (IAM) � Ti/w1 started 183 Session Progress (ACM)

� Ti/w1 expired � INVITE

180 Ringing (CPG) � � 180 Ringing Apply post test routine

ETSI

ETSI TS 101 572-2 V1.2.1 (2014-07)132


TSS reference SIP-I - SIP NNI/Basic call/Sending_of_CPG in encapsulated 18x message/ Selection criteria PICS 6.2.1/5 Test Purpose name Mapping of PSTN XML ProgressIndicator 4 in 180 into ATP in the CPG Test Purpose Ensure that on receipt of a PSTN XML ProgressIndicator value 4 in a 180 Ringing a 180



SIP Parameter values 180: <?xml version="1.0" encoding="utf-8"?> PSTN ProgressIndicator ProgressOctet4 ProgressDescription>0000001< or ProgressDescription>0000010< 180: <?xml version="1.0" encoding="utf-8"?> PSTN ProgressIndicator ProgressOctet4 ProgressDescription>0000100<






TSS reference SIP-I - SIP NNI/Basic call/Sending_of_CPG in encapsulated 18x message/ Selection criteria PICS 6.2.1/5 Test Purpose name No mapping of PSTN XML ProgressIndicator 7 in 180 into ATP in the CPG Test Purpose Ensure that on receipt of a PSTN XML ProgressIndicator value 7 in a 180 Ringing, a 180

Ringing with encapsulated CPG is sent and no Access Transport Parameter is present containing a Progress Indicator #7

ISUP Parameter values CPG: Access Transport not present SIP Parameter values 183:






ETSI

ETSI TS 101 572-2 V1.2.1 (2014-07)133

TP number TP_204_021 Reference [2], clause 7.2.3.2.6 TSS reference SIP-I - SIP NNI/Basic call/Sending_of_CPG in encapsulated 18x message/ Selection criteria PICS 6.2.1/5 Test Purpose name Mapping of PSTN XML ProgressIndicator 8 in 180 into Event information in the CPG Test Purpose Ensure that on receipt of a PSTN XML ProgressIndicator value 8 in a 180 Ringing, a 180

Ringing with encapsulated CPG is sent and Event information parameter is set to 'In-band information or appropriate pattern is now available'

ISUP Parameter values CPG: Event information= In-band information or appropriate pattern is now available SIP Parameter values 183:





180 Ringing (CPG) � � 180 Ringing



TSS reference SIP-I - SIP NNI/Basic call/Sending_of_CPG in encapsulated 18x message/ Selection criteria PICS 6.2.1/9 Test Purpose name Mapping of P-Early-Media header into Event information parameter in CPG Test Purpose Ensure that on receipt of a 183 Session Progress and a P-Early-Media header is present

authorizing early media, a 183 Session Progress with encapsulated CPG is sent. The Event information parameter is set to 'In-band information or appropriate pattern is now available'

ISUP Parameter values CPG: Event information= In-band information or appropriate pattern is now available SIP Parameter values 183: P-Early-Media: sendonly Comments Message flows SIP-I MGCF SIP NNI






ETSI

ETSI TS 101 572-2 V1.2.1 (2014-07)134


TSS reference SIP-I - SIP NNI/Basic call/Sending_of_CPG in encapsulated 18x message/ Selection criteria NOT PICS 6.2.1/18 Test Purpose name 180 received, coding of Backward call indicator in CPG TMR speech or 3,1 kHz audio Test Purpose IAM with Transmission Medium Requirement indicator=speech or 3,1 kHz received.

Ensure that on receipt of a 180 Ringing response, a 180 Ringing with encapsulated CPG is sent and the Backward call indicator is set to the following values: • Charge indicator = charge (10) • Called party's status indicator = subscriber free (01) • Called party's category indicator = no indication (00) • End-to-end method indicator = no end-to-end method available (00) • Interworking indicator = interworking encountered (1) • End-to-end information indicator = no end-to-end information available (0) • ISDN user part/BICC indicator = ISDN user part not used all the way (0) • ISDN access indicator = terminating access non-ISDN (0) • Echo control device indicator = incoming echo control device included (1)

ISUP Parameter values IAM: Transmission Medium Requirement indicator=speech or 3,1 kHz ACM: Backward call indicator Called party's status indicator = no indication






TSS reference SIP-I - SIP NNI/Basic call/Sending_of_CPG in encapsulated 18x message/ Selection criteria PICS 6.2.4/2 AND NOT PICS 6.2.1/18 Test Purpose name 180 received, coding of Backward call indicator in CPG TMR 64 kBit/s unrestricted Test Purpose IAM with Transmission Medium Requirement indicator=64 kBit/s unrestricted received.

Ensure that on receipt of a 180 Ringing response, a 180 Ringing with encapsulated CPG is sent and the Backward call indicator is set to the following values: • Charge indicator = charge (10) • Called party's status indicator = subscriber free (01) • Called party's category indicator = no indication (00) • End-to-end method indicator = no end-to-end method available (00) • Interworking indicator = interworking encountered (1) • End-to-end information indicator = no end-to-end information available (0) • ISDN user part/BICC indicator = ISDN user part not used all the way (0) • ISDN access indicator = terminating access non-ISDN (0) • Echo control device indicator = incoming echo control device not included (0)

ISUP Parameter values IAM: Transmission Medium Requirement indicator=64 kBit/s unrestricted ACM: Backward call indicator Called party's status indicator = no indication

SIP Parameter values Comments Message flows SIP SIP-I MGCF SIP NNI




ETSI

ETSI TS 101 572-2 V1.2.1 (2014-07)135


TSS reference SIP-I - SIP NNI/Basic call/Sending_of_CPG in encapsulated 18x message/ Selection criteria PICS 6.2.4/2 AND PICS 6.2.1/18 Test Purpose name 180 received, coding of Backward call indicator in CPG TMR 64 kBit/s unrestricted Test Purpose IAM with Transmission Medium Requirement indicator=64 kBit/s unrestricted received.

Ensure that on receipt of a 180 Ringing response, a 180 Ringing with encapsulated CPG is sent and the Backward call indicator is set to the following values: • Charge indicator = charge (10) • Called party's status indicator = subscriber free (01) • Called party's category indicator = no indication (00) • End-to-end method indicator = no end-to-end method available (00) • Interworking indicator = no interworking encountered (0) • End-to-end information indicator = no end-to-end information available (0) • ISDN user part/BICC indicator = ISDN user part used all the way (1) • ISDN access indicator = terminating access ISDN (1) • Echo control device indicator = incoming echo control device not included (0)







TSS reference SIP-I - SIP NNI/Basic call/Sending_of_CPG in encapsulated 18x message/ Selection criteria Test Purpose name 180 received, coding of Backward call indicator in CPG HLC "Facsimile Group 2/3" Test Purpose IAM with Transmission Medium Requirement indicator=3,1 kHz and High Layer

Compatibility= Facsimile Group 2/3 received. Ensure that on receipt of a 180 Ringing response, a 180 Ringing with encapsulated CPG is sent and the Backward call indicator is set to the following values: • Charge indicator = charge (10) • Called party's status indicator = subscriber free (01) • Called party's category indicator = no indication (00) • End-to-end method indicator = no end-to-end method available (00) • Interworking indicator = interworking encountered (1) • End-to-end information indicator = no end-to-end information available (0) • ISDN user part/BICC indicator = ISDN user part not used all the way (0) • ISDN access indicator = terminating access non-ISDN (0) • Echo control device indicator = incoming echo control device not included (0)

ISUP Parameter values IAM: Transmission Medium Requirement indicator=3,1 kHz High Layer Compatibility= Facsimile Group 2/3 ACM: Backward call indicator Called party's status indicator = no indication





ETSI

ETSI TS 101 572-2 V1.2.1 (2014-07)136

6.1.2.5 Sending of the Answer Message (ANM)


TSS reference SIP-I - SIP NNI/Basic call/200 OK INVITE with encapsulated ANM / Selection criteria Test Purpose name Sending of ANM when 200 OK INVITE was received Test Purpose Ensure that upon receipt of the first 200 OK (INVITE), if the Address Complete Message

(ACM) has already been sent, the SUT sends the Answer Message (ANM) ISUP Parameter values SIP Parameter values Comments Message flows SIP-I MGCF SIP NNI

INVITE (IAM) � � INVITE � 100 Trying 180 Ringing (ACM) � � 180 Ringing 200 OK (INVITE) (ANM)

� � 200 OK (INVITE)

ACK � � ACK Apply post test routine


TSS reference SIP-I - SIP NNI/Basic call/200 OK INVITE with encapsulated ANM 200 OK INVITE with encapsulated ANM /

Selection criteria NOT PICS 6.2.1/18 Test Purpose name 200 OK received, coding of Backward call indicator in ANM TMR speech or 3,1 kHz audio Test Purpose INVITE with encapsulated IAM with Transmission Medium Requirement indicator=speech

or 3,1 kHz received. Ensure that on receipt of a 200 OK INVITE final response, a 200 OK INVITE with encapsulated ANM is sent and the Backward call indicator is set to the following values: • Charge indicator = charge (10) • Called party's status indicator = no indication (00) • Called party's category indicator = no indication (00) • End-to-end method indicator = no end-to-end method available (00) • Interworking indicator = interworking encountered (1) • End-to-end information indicator = no end-to-end information available (0) • ISDN user part/BICC indicator = ISDN user part not used all the way (0) • ISDN access indicator = terminating access non-ISDN (0) • Echo control device indicator = Incoming echo control device included (1)

ISUP Parameter values IAM: Transmission Medium Requirement indicator=speech or 3,1 kHz ACM: Backward call indicator Called party's status indicator = no indication

SIP Parameter values 183: P-Early-Media: sendonly Comments Message flows SIP-I MGCF SIP NNI



� 183 Session Progress 200 OK (INVITE) (ANM)



ETSI

ETSI TS 101 572-2 V1.2.1 (2014-07)137


TSS reference SIP-I - SIP NNI/Basic call/200 OK INVITE with encapsulated ANM / Selection criteria PICS 6.2.4/2 AND NOT PICS 6.2.1/18 Test Purpose name 200 OK received, coding of Backward call indicator in ANM TMR 64 kBit/s unrestricted Test Purpose INVITE with encapsulated IAM with Transmission Medium Requirement indicator=64 kBit/s

unrestricted received. Ensure that on receipt of a 200 OK INVITE final response, an 200 OK INVITE with encapsulated ANM is sent and the Backward call indicator is set to the following values: • Charge indicator = charge (10) • Called party's status indicator = no indication (00) • Called party's category indicator = no indication (00) • End-to-end method indicator = no end-to-end method available (00) • Interworking indicator = interworking encountered (1) • End-to-end information indicator = no end-to-end information available (0) • ISDN user part/BICC indicator = ISDN user part not used all the way (0) • ISDN access indicator = terminating access non-ISDN (0) • Echo control device indicator = Incoming echo control device not included (0)





� 183 Session Progress 200 OK (INVITE)(ANM)



ETSI

ETSI TS 101 572-2 V1.2.1 (2014-07)138


TSS reference SIP-I - SIP NNI/Basic call/200 OK INVITE with encapsulated ANM / Selection criteria PICS 6.2.4/2 AND PICS 6.2.1/18 Test Purpose name 200 OK received, coding of Backward call indicator in ANM TMR 64 kBit/s unrestricted Test Purpose INVITE with encapsulated IAM with Transmission Medium Requirement indicator=64 kBit/s

unrestricted received. Ensure that on receipt of a 200 OK INVITE final response, an 200 OK INVITE with encapsulated ANM is sent and the Backward call indicator is set to the following values: • Charge indicator = charge (10) • Called party's status indicator = no indication (00) • Called party's category indicator = no indication (00) • End-to-end method indicator = no end-to-end method available (00) • Interworking indicator = no interworking encountered (0) • End-to-end information indicator = no end-to-end information available (0) • ISDN user part/BICC indicator = ISDN user part used all the way (1) • ISDN access indicator = terminating access ISDN (1) • Echo control device indicator = Incoming echo control device not included (0)



INVITE (IAM) � Ti/w1 started Session Progress (ACM)





ETSI

ETSI TS 101 572-2 V1.2.1 (2014-07)139


TSS reference SIP-I - SIP NNI/Basic call/200 OK INVITE with encapsulated ANM / Selection criteria PICS 6.2.1/9 Test Purpose name 200 OK received, coding of Backward call indicator in ANM HLC "Facsimile Group 2/3" Test Purpose INVITE with encapsulated IAM with Transmission Medium Requirement indicator=3,1 kHz

and High Layer Compatibility= Facsimile Group 2/3 received. Ensure that on receipt of a 200 OK INVITE final response, a 200 OK INVITE with encapsulated ANM is sent and the Backward call indicator is set to the following values: • Charge indicator = charge (10) • Called party's status indicator = no indication (00) • Called party's category indicator = no indication (00) • End-to-end method indicator = no end-to-end method available (00) • Interworking indicator = interworking encountered (1) • End-to-end information indicator = no end-to-end information available (0) • ISDN user part/BICC indicator = ISDN user part not used all the way (0) • ISDN access indicator = terminating access non-ISDN (0) • Echo control device indicator = Incoming echo control device not included (0)

ISUP Parameter values IAM: Transmission Medium Requirement indicator=3,1 kHz High Layer Compatibility= Facsimile Group 2/3 ACM: Backward call indicator Called party's status indicator = no indication


INVITE (IAM) � Ti/w1 started Session Progress (ACM)






TSS reference SIP-I - SIP NNI/Basic call/200 OK INVITE with encapsulated ANM / Selection criteria PICS 6.2.1/5 Test Purpose name Mapping of PSTN XML ProgressIndicator 1 in 200 OK into ATP in the ANM Test Purpose Ensure that on receipt of a PSTN XML ProgressIndicator value 1 in a 200 OK INVITE, an

ANM is sent and an Access Transport Parameter is present containing a Progress Indicator #1

ISUP Parameter values ANM: Access Transport Progress Indicator Progress Description='0000001'

SIP Parameter values 200 OK: <?xml version="1.0" encoding="utf-8"?> PSTN ProgressIndicator ProgressOctet4 ProgressDescription>0000001<


INVITE (IAM) � � INVITE � 100 Trying 180 Ringing (ACM – free)

� � 180 Ringing

200 OK (INVITE) ANM



ETSI

ETSI TS 101 572-2 V1.2.1 (2014-07)140


TSS reference SIP-I - SIP NNI/Basic call/200 OK INVITE with encapsulated ANM / Selection criteria PICS 6.2.1/5 Test Purpose name Mapping of PSTN XML ProgressIndicator 2 in 200 OK into ATP in the ANM Test Purpose Ensure that on receipt of a PSTN XML ProgressIndicator value 2 in a 200 OK INVITE, a

200 OK INVITE with encapsulated ANM is sent and an Access Transport Parameter is present containing a Progress Indicator #2
















ETSI

ETSI TS 101 572-2 V1.2.1 (2014-07)141




ISUP Parameter values IAM: USI=speech or 3,1 kHz audio, USI prime=unrestricted digital info with T/A, TMR=64 kbit/s preferred, TMR prime = speech or 3,1 kHz audio ANM: Access Transport Progress Indicator Progress Description='0000101'






ETSI

ETSI TS 101 572-2 V1.2.1 (2014-07)142


TSS reference SIP-I - SIP NNI/Basic call/200 OK INVITE with encapsulated ANM / Selection criteria PICS 6.2.1/5 Test Purpose name No mapping of PSTN XML ProgressIndicator 7 in 200 OK into ATP in the ANM Test Purpose Ensure that on receipt of a PSTN XML ProgressIndicator value 7 in a 200 OK INVITE, a

200 OK INVITE with encapsulated ANM is sent and no Access Transport Parameter is present containing a Progress Indicator #7. The Backward call indicator is set to the following values: ISDN User Part indicator ISDN User Part used all the way ISDN access indicator Terminating access ISDN Interworking indicator no interworking encountered

ISUP Parameter values ANM: Access Transport not present Backward call indicator ISDN User Part indicator ISDN User Part used all the way ISDN access indicator Terminating access ISDN Interworking indicator no interworking encountered



INVITE (IAM) � � INVITE � 100 Trying 180 Ringing ( (ACM - free)

� � 180 Ringing

200 OK (INVITE) (ANM)



ETSI

ETSI TS 101 572-2 V1.2.1 (2014-07)143


TSS reference SIP-I - SIP NNI/Basic call/200 OK INVITE with encapsulated ANM / Selection criteria PICS 6.2.1/5 Test Purpose name Mapping of PSTN XML HighLayerCompatibility in 200 OK into ATP in ANM Test Purpose Ensure that on receipt of 200 OK INVITE and a PSTN XML HighLayerCompatibility

element is present a 200 OK INVITE with encapsulated ANM is sent and a Access Transport Parameter is present containing a High layer compatibility IE and the value is set to the value HLC_VA as indicated in table 6.1.2.5-1

ISUP Parameter values ANM: Access Transport High layer compatibility High layer characteristics identification = HLC_VA

SIP Parameter values 200 OK: PSTN XML MIME body <?xml version="1.0" encoding="utf-8"?> PSTN HighLayerCompatibility HLOctet3 CodingStandard>00< Interpretation>100< PresentationMethod>01< HLOctet4 HighLayerCharacteristics>HLC_VA<


INVITE (IAM) � � INVITE � 100 Trying 180 Ringing (ACM)

� � 180 Ringing




Table 6.1.2.5-1: Mapping of PSTN XML HighLayerCharacteristic into ISUP ATP High layer compatibility

HLC_VA XML HighLayerCharacteristic DSS1 High layer characteristics identification HLC_VA_1 '0000001' Telephony HLC_VA_2 '0000100' Facsimile Group 2/3 HLC_VA_3 '0100001' Facsimile Group 4 Class I HLC_VA_4 '0100100' Facsimile service Group 4, Classes II and III HLC_VA_5 '0110010' Syntax based Videotex HLC_VA_6 '0110011' International Videotex interworking via gateways

or interworking units HLC_VA_7 '0110101' Telex service HLC_VA_8 '1000010' FTAM application HLC_VA_9 '1100000' Videotelephony

ETSI

ETSI TS 101 572-2 V1.2.1 (2014-07)144


TSS reference SIP-I - SIP NNI/Basic call/200 OK INVITE with encapsulated ANM / Selection criteria PICS 6.2.1/5 Test Purpose name Mapping of PSTN XML BearerCapability in 200 OK into ATP in ANM Test Purpose Ensure that on receipt of 200 OK INVITE and a PSTN XML BearerCapability element is

present, a 200 OK INVITE with encapsulated ANM is sent and a Access Transport Parameter is present containing a Bearer Capability IE and the value is set to the value ITC_value as indicated in table 6.1.2.5-1

ISUP Parameter values IAM: USI=speech or 3,1 kHz audio, USI prime=unrestricted digital info with T/A, TMR=64 kbit/s preferred, TMR prime = speech or 3,1 kHz audio ANM: Access Transport Bearer Capability Information Transfer Capability = ITC_value

SIP Parameter values 200 OK: <?xml version="1.0" encoding="utf-8"?> PSTN BearerCapability BCoctet3 CodingStandard>00< InformationTransferCapability> ITC_value < BCoctet4 TransferMode>00< InformationTransferRate>10000<





Table 6.1.2.5-2: Mapping of PSTN XML BearerCapability into ISUP ATP Bearer Capability

ITC_value XML InformationTransferCapability BC Information transfer capability VA_01 '00000' Speech VA_02 '10000' 3,1 kHz audio VA_03 '10001' Unrestricted digital information with

tones/announcements

ETSI

ETSI TS 101 572-2 V1.2.1 (2014-07)145


TSS reference SIP-I - SIP NNI/Basic call/200 OK INVITE with encapsulated ANM / Selection criteria PICS 6.2.1/5 Test Purpose name Mapping of PSTN XML BearerCapability into Transmission medium used parameter Test Purpose Ensure that on receipt of a PSTN XML BearerCapability element in a 200 OK INVITE a

Transmission Medium Used parameter is present in the sent 200 OK INVITE with encapsulated ANM message. The value of the PSTN XML InformationTransferCapability value TMU_VA_BC is mapped into the value of the Transmission Medium Used parameter TMU_VA_TMU as described in table 6.1.2.5-3

ISUP Parameter values IAM: USI=speech or 3,1 kHz audio, USI prime=unrestricted digital info with T/A, TMR=64 kbit/s preferred, TMR prime = speech or 3,1 kHz audio ANM: TMU: TMU_VA_TMU

SIP Parameter values 200 OK: <?xml version="1.0" encoding="utf-8"?> PSTN BearerCapability BCoctet3 CodingStandard>00< InformationTransferCapability>TMU_VA_BC< ….


INVITE (IAM) � � INVITE � 100 Trying 180 Ringing (ACM – free) � � 180 Ringing 200 OK (INVITE) (ANM) � � 200 OK (INVITE) ACK � � ACK


Table 6.1.2.5-3: Mapping of PSTN XML BearerCapability into ISUP TMU parameter

TMU_VA PSTN XML BearerCapability TMU_VA_BC TMU value TMU_VA_TMU

TMU_VA_01 '00000' 'speech' TMU_VA_02 '10000' '3,1 kHz audio' TMU_VA_03 '10001' No mapping (see note 1) TMU_VA_04 Not present (see note 2) '3,1 kHz audio' NOTE 1: The value of 'UDITA' is sent when fallback does not occur. NOTE 2: The absence of a PSTN XML attachment indicates that a non ISDN destination is reached.

6.1.2.6 Sending of the 200 OK (INVITE) with encapsulated Connect message (CON)


TSS reference SIP-I - SIP NNI/Basic call/Sending_of_200_OK_INVITE_with_encapsulated CON/ Selection criteria Test Purpose name Sending of CON message after 200 OK was received Test Purpose Ensure that on receipt of a 200 OK INVITE and no ACM was sent, a 200 OK INVITE with

encapsulated CON message is sent ISUP Parameter values SIP Parameter values Comments Message flows SIP-I MGCF SIP NNI

INVITE (IAM) � � INVITE � 100 Trying 200 OK (INVITE) (CON) � � 200 OK (INVITE) ACK � � ACK


ETSI

ETSI TS 101 572-2 V1.2.1 (2014-07)146


TSS reference SIP-I - SIP NNI/Basic call/Sending_of_200_OK_INVITE_with_encapsulated CON/ Selection criteria NOT PICS 6.2.1/18 Test Purpose name 200 OK received, coding of Backward call indicator in CON TMR speech or 3,1 kHz audio Test Purpose IAM with Transmission Medium Requirement indicator=speech or 3,1 kHz received.

Ensure that on receipt of a 200 OK INVITE final response, a 200 OK INVITE with encapsulated CON is sent and the Backward call indicator is set to the following values: • Charge indicator = charge (10) • Called party's status indicator = no indication (00) • Called party's category indicator = no indication (00) • End-to-end method indicator = no end-to-end method available (00) • Interworking indicator = interworking encountered (1) • End-to-end information indicator = no end-to-end information available (0) • ISDN user part/BICC indicator = ISDN user part not used all the way (0) • ISDN access indicator = terminating access non-ISDN (0) • Echo control device indicator = Incoming echo control device included (1)

ISUP Parameter values IAM: Transmission Medium Requirement indicator=speech or 3,1 kHz CON: Backward call indicator Called party's status indicator = no indication


INVITE (IAM) � � INVITE � 100 Trying 200 OK (INVITE)CON � � 200 OK (INVITE) ACK � � ACK



TSS reference SIP-I - SIP NNI/Basic call/Sending_of_200_OK_INVITE_with_encapsulated CON/ Selection criteria PICS 6.2.4/2 AND NOT PICS 6.2.1/18 Test Purpose name 200 OK received, coding of Backward call indicator in CON TMR 64 kBit/s unrestricted Test Purpose IAM with Transmission Medium Requirement indicator=64 kBit/s unrestricted received.

Ensure that on receipt of a 200 OK INVITE final response, a 200 OK INVITE with encapsulated CON is sent and the Backward call indicator is set to the following values: • Charge indicator = charge (10) • Called party's status indicator = no indication (00) • Called party's category indicator = no indication (00) • End-to-end method indicator = no end-to-end method available (00) • Interworking indicator = interworking encountered (1) • End-to-end information indicator = no end-to-end information available (0) • ISDN user part/BICC indicator = ISDN user part not used all the way (0) • ISDN access indicator = terminating access non-ISDN (0) • Echo control device indicator = Incoming echo control device not included (0)

ISUP Parameter values IAM: Transmission Medium Requirement indicator=64 kBit/s unrestricted CON: Backward call indicator Called party's status indicator = no indication


INVITE (IAM) � � INVITE � 100 Trying 200 OK (INVITE)CON � � 200 OK (INVITE) ACK � � ACK


ETSI

ETSI TS 101 572-2 V1.2.1 (2014-07)147


TSS reference SIP-I - SIP NNI/Basic call/Sending_of_200_OK_INVITE_with_encapsulated CON/ Selection criteria PICS 6.2.4/2 AND PICS 6.2.1/18 Test Purpose name 200 OK received, coding of Backward call indicator in ANM TMR 64 kBit/s unrestricted Test Purpose IAM with Transmission Medium Requirement indicator=64 kBit/s unrestricted received.

Ensure that on receipt of a 200 OK INVITE final response, a 200 OK INVITE with encapsulated CON is sent and the Backward call indicator is set to the following values: • Charge indicator = charge (10) • Called party's status indicator = no indication (00) • Called party's category indicator = no indication (00) • End-to-end method indicator = no end-to-end method available (00) • Interworking indicator = no interworking encountered (0) • End-to-end information indicator = no end-to-end information available (0) • ISDN user part/BICC indicator = ISDN user part used all the way (1) • ISDN access indicator = terminating access ISDN (1) • Echo control device indicator = Incoming echo control device not included (0)

ISUP Parameter values IAM: Transmission Medium Requirement indicator=64 kBit/s unrestricted CON: Backward call indicator Called party's status indicator = no indication


INVITE (IAM) � � INVITE � 100 Trying 200 OK (INVITE) CON � � 200 OK (INVITE) ACK � � ACK



TSS reference SIP-I - SIP NNI/Basic call/Sending_of_200_OK_INVITE_with_encapsulated CON/ Selection criteria Test Purpose name 200 OK received, coding of Backward call indicator in CON HLC "Facsimile Group 2/3" Test Purpose IAM with Transmission Medium Requirement indicator=3,1 kHz and High Layer

Compatibility= Facsimile Group 2/3 received. Ensure that on receipt of a 200 OK INVITE final response, a 200 OK INVITE with encapsulated CON is sent and the Backward call indicator is set to the following values: • Charge indicator = charge (10) • Called party's status indicator = no indication (00) • Called party's category indicator = no indication (00) • End-to-end method indicator = no end-to-end method available (00) • Interworking indicator = interworking encountered (1) • End-to-end information indicator = no end-to-end information available (0) • ISDN user part/BICC indicator = ISDN user part not used all the way (0) • ISDN access indicator = terminating access non-ISDN (0) • Echo control device indicator = Incoming echo control device not included (0)

ISUP Parameter values IAM: Transmission Medium Requirement indicator=3,1 kHz High Layer Compatibility= Facsimile Group 2/3 CON: Backward call indicator Called party's status indicator = no indication




ETSI

ETSI TS 101 572-2 V1.2.1 (2014-07)148


TSS reference SIP-I - SIP NNI/Basic call/Sending_of_200_OK_INVITE_with_encapsulated CON/ Selection criteria PICS 6.2.1/5 Test Purpose name Mapping of PSTN XML ProgressIndicator 1 in 200 OK into ATP in the CON Test Purpose Ensure that on receipt of a PSTN XML ProgressIndicator value 1 in a 200 OK INVITE, a

200 OK INVITE with encapsulated CON is sent and an Access Transport Parameter is present containing a Progress Indicator #1

ISUP Parameter values CON: Access Transport Progress Indicator Progress Description='0000001'











INVITE (IAM) � � INVITE � 100 Trying 200 OK (INVITE) (CON) � � 200 OK (INVITE) � ACK


ETSI

ETSI TS 101 572-2 V1.2.1 (2014-07)149







INVITE (IAM) � � INVITE � 100 Trying 200 OK (INVITE)(CON) � � 200 OK (INVITE) ACK � � ACK





ISUP Parameter values IAM: USI=speech or 3,1 kHz audio, USI prime=unrestricted digital info with T/A, TMR=64 kbit/s preferred, TMR prime = speech or 3,1 kHz audio CON: Access Transport Progress Indicator Progress Description='0000101'





ETSI

ETSI TS 101 572-2 V1.2.1 (2014-07)150


TSS reference SIP-I - SIP NNI/Basic call/Sending_of_200_OK_INVITE_with_encapsulated CON/ Selection criteria PICS 6.2.1/5 Test Purpose name No mapping of PSTN XML ProgressIndicator 7 in 200 OK into ATP in the CON Test Purpose Ensure that on receipt of a PSTN XML ProgressIndicator value 7 in a 200 OK INVITE, a

200 OK INVITE with encapsulated CON is sent and no Access Transport Parameter is present containing a Progress Indicator #7. The Backward call indicator is set to the following values: ISDN User Part indicator ISDN User Part used all the way ISDN access indicator Terminating access non-ISDN Interworking indicator no interworking encountered

ISUP Parameter values CON: Access Transport not present Backward call indicator ISDN User Part indicator ISDN User Part used all the way ISDN access indicator Terminating access non-ISDN Interworking indicator no interworking encountered





ETSI

ETSI TS 101 572-2 V1.2.1 (2014-07)151


TSS reference SIP-I - SIP NNI/Basic call/Sending_of_200_OK_INVITE_with_encapsulated CON/ Selection criteria PICS 6.2.1/5 Test Purpose name Mapping of PSTN XML HighLayerCompatibility in 200 OK into ATP in CON Test Purpose Ensure that on receipt of 200 OK INVITE and a PSTN XML HighLayerCompatibility

element is present a 200 OK INVITE with encapsulated CON is sent and a Access Transport Parameter is present containing a High layer compatibility IE and the value is set to the value HLC_VA as indicated in table 6.1.2.5-1

ISUP Parameter values CON: Access Transport High layer compatibility High layer characteristics identification = HLC_VA

SIP Parameter values 200 OK: PSTN XML MIME body <?xml version="1.0" encoding="utf-8"?> PSTN HighLayerCompatibility HLOctet3 CodingStandard>00< Interpretation>100< PresentationMethod>01< HLOctet4 HighLayerCharacteristics>HLC_VA<

Comments Message flows SIP-I MGCF IP NNIP




TSS reference SIP-I - SIP NNI/Basic call/Sending_of_200_OK_INVITE_with_encapsulated CON/ Selection criteria PICS 6.2.1/5 Test Purpose name Mapping of PSTN XML BearerCapability in 200 OK into ATP in CON Test Purpose Ensure that on receipt of 200 OK INVITE and a PSTN XML BearerCapability element is

present, a 200 OK INVITE with encapsulated CON is sent and a Access Transport Parameter is present containing a Bearer Capability IE and the value is set to the value ITC_value as indicated in table 6.1.2.5-1

ISUP Parameter values CON: Access Transport Bearer Capability Information Transfer Capability = ITC_value

SIP Parameter values 200 OK: <?xml version="1.0" encoding="utf-8"?> PSTN BearerCapability BCoctet3 CodingStandard>00< InformationTransferCapability> ITC_value < BCoctet4 TransferMode>00< InformationTransferRate>10000<




ETSI

ETSI TS 101 572-2 V1.2.1 (2014-07)152


TSS reference SIP-I - SIP NNI/Basic call/Sending_of_200_OK_INVITE_with_encapsulated CON/ Selection criteria PICS 6.2.1/5 Test Purpose name Mapping of PSTN XML BearerCapability into Transmission medium used parameter Test Purpose Ensure that on receipt of a PSTN XML BearerCapability element in a 200 OK INVITE a

Transmission Medium Used parameter is present in the sent 200 OK INVITE with encapsulated CON message. The value of the PSTN XML InformationTransferCapability value TMU_VA_BC is mapped into the value of the Transmission Medium Used parameter TMU_VA_TMU as described in table 6.1.2.5-3

ISUP Parameter values IAM: USI=speech or 3,1 kHz audio, USI prime=unrestricted digital info with T/A, TMR=64 kbit/s preferred, TMR prime = speech or 3,1 kHz audio CON: TMU: TMU_VA_TMU

SIP Parameter values 200 OK: <?xml version="1.0" encoding="utf-8"?> PSTN BearerCapability BCoctet3 CodingStandard>00< InformationTransferCapability>TMU_VA_BC< ….





TSS reference SIP-I - SIP NNI/Basic call/Sending_of_200_OK_INVITE_with_encapsulated CON/ Selection criteria PICS 6.2.1/19 Test Purpose name Receipt of a reINVITE request Test Purpose Ensure that on receipt of a reINVITE received from the SIP network containing a Call-Info

header, the SUT instruct the MGW to send the associated media to the PSTN leg of the communication

ISUP Parameter values SIP Parameter values INVITE2: Call-Info: <media resource URL> Comments Message flows SIP-I MGCF SIP NNI

INVITE (IAM) � � INVITE1 180 Ringing (ACM free) � � 180 Ringing 200 OK INVITE (ANM) � � 200 OK INVITE ACK � � ACK INVITE � � INVITE 200 OK INVITE2 � 200 OK INVITE2 ACK � � ACK

media Apply post test routine

ETSI

ETSI TS 101 572-2 V1.2.1 (2014-07)153

6.1.2.7 Receipt of Status Codes 3xx, 4xx, 5xx or 6xx


TSS reference SIP-I - SIP NNI/Basic call/Receipt_of_4xx-5xx-6xx/ Selection criteria Test Purpose name Mapping of unsuccessful final responses to ISUP/BICC Release messages Test Purpose Ensure that on receipt of an unsuccessful final response SIP_Response before an early

dialogue is established, a SIP_Response with encapsulated Release message Cause value REL_cause is sent on the ISUP/BICC leg of the connection. The mapping is according the table 6.1.2.7-1. The location value in the REL message is set to 'network beyond interworking point'

ISUP Parameter values REL: Cause = REL_cause SIP Parameter values SIP_Response Comments Message flows SIP-I MGCF SIP NNI

INVITE (IAM) � � INVITE � 100 Trying SIP_Response (REL) � � SIP_Response ACK (RLC) � � ACK

ETSI

ETSI TS 101 572-2 V1.2.1 (2014-07)154

Table 6.1.2.7-1: Received status codes on SIP side of O-MGCF mapping to REL

SIP_Response_VA ←REL (cause code) REL_cause

←4xx/5xx/6xx SIP Message SIP_Response

VA_01 111 (protocol error, unspecified) 400 Bad Request VA_02 127 (interworking unspecified) 401 Unauthorized VA_03 127 (interworking unspecified) 402 Payment Required VA_04 79 (Service or option not implemented,

unspecified) 403 Forbidden

VA_05 1 (Unallocated number) 404 Not Found VA_06 127 (interworking unspecified) 405 Method Not Allowed VA_07 127 (interworking unspecified) 406 Not Acceptable VA_08 127 (interworking unspecified) 407 Proxy authentication required VA_09 102 (recovery on timer expiry) 408 Request Timeout VA_10 22 (Number changed) 410 Gone VA_11 127 (interworking unspecified) 413 Request Entity too long VA_12 111 (protocol error, unspecified) 414 Request-URI too long VA_13 127 (interworking unspecified) 415 Unsupported Media type VA_14 111 (protocol error, unspecified) 416 Unsupported URI scheme VA_15 79 (Service or option not implemented,

unspecified) 417 Unknown Resource-Priority

VA_16 111 (protocol error, unspecified) 420 Bad Extension VA_17 111 (protocol error, unspecified) 421 Extension required VA_18 31 (Normal, unspecified) 422 Session Interval Too Small VA_19 127 (interworking unspecified) 423 Interval Too Brief VA_20 24 (call rejected due to ACR supplementary

service) 433 Anonymity Disallowed.

VA_21 20 Subscriber absent 480 Temporarily Unavailable VA_22 127 (interworking unspecified) 440 Max-Breadth Exceeded VA_23 127 (interworking unspecified) 481 Call/Transaction does not exist VA_24 127 (interworking unspecified) 482 Loop detected VA_25 25 (Exchange routing error) 483 Too many hops VA_26 28 (Invalid Number format) 484 Address Incomplete VA_27 Cause value No. 1 (unallocated

(unassigned) number) 485 Ambiguous

VA_28 17 (User busy) 486 Busy Here VA_29 127 (Interworking unspecified) or not

interworked 487 Request terminated

VA_30 50 (requested facility no subscribed) 488 Not acceptable here VA_31 127 (interworking unspecified) 493 Undecipherable VA_32 127 (interworking unspecified) 500 Server Internal error VA_33 79 (service or option not implemented) 501 Not implemented VA_34 27 (Destination out of order) 502 Bad Gateway VA_35 127 (interworking unspecified) 503 Service Unavailable VA_36 102 (Recovery on timer expiry) 504 Server timeout VA_37 127 (interworking unspecified) 505 Version not supported VA_38 127 (interworking unspecified) 513 Message too large VA_39 127 (interworking unspecified) 580 Precondition failure VA_40 17 (User busy) 600 Busy Everywhere VA_41 21 (Call rejected) 603 Decline VA_42 2 (No route to specified transit network) 604 Does not exist anywhere VA_43 88 (incompatible destination) 606 Not acceptable

ETSI

ETSI TS 101 572-2 V1.2.1 (2014-07)155


TSS reference SIP-I - SIP NNI/Basic call/Receipt_of_4xx-5xx-6xx/ Selection criteria Test Purpose name Mapping of unsuccessful final responses to REL after 180 was received Test Purpose Ensure that on receipt of an unsuccessful final response SIP_Response with encapsulated

(REL) after an early dialogue was established due to the receipt of a 180 Ringing, a REL is sent. The Cause value of the REL is mapped from the received status code as indicated in table 6.1.2.7-2. The location value in the REL message is set to 'network beyond interworking point'


INVITE (IAM) � � INVITE � 100 Trying 180 Ringing (ACM) � 180 Ringing SIP_Response (REL) � � SIP_Response ACK (RLC) � � ACK



(REL) after an early dialogue was established due to the receipt of a 181 Call is Being Forwarded, a REL is sent. The Cause value of the REL is mapped from the received status code as indicated in table 6.1.2.7-2. The location value in the REL message is set to 'network beyond interworking point'


INVITE (IAM) � � INVITE � 100 Trying 181 Call is Being Forwarded (ACM)

� 181 Call is Being Forwarded

SIP_Response (REL) � � SIP_Response ACK (RLC) � � ACK



(REL)after an early dialogue was established due to the receipt of a 183 Session Progress, a REL is sent. The Cause value of the REL is mapped from the received status code as indicated in table 6.1.2.7-2. The location value in the REL message is set to 'network beyond interworking point'


IAM � � INVITE � 100 Trying 183 Session Progress � � 183 Session Progress SIP_Response (REL) � � SIP_Response ACK (RLC) � � ACK

ETSI

ETSI TS 101 572-2 V1.2.1 (2014-07)156


SIP_Response_VA ←REL (cause code) REL_cause


VA_01 111 (protocol error, unspecified) 400 Bad Request VA_02 127 (interworking unspecified) 402 Payment Required VA_03 79 (Service or option not implemented,

unspecified) 403 Forbidden

VA_04 127 (interworking unspecified) 406 Not Acceptable VA_05 102 (recovery on timer expiry) 408 Request Timeout VA_06 22 (Number changed) 410 Gone VA_07 127 (interworking unspecified) 423 Interval Too Brief VA_08 20 Subscriber absent 480 Temporarily Unavailable VA_09 127 (interworking unspecified) 481 Call/Transaction does not exist VA_10 127 (interworking unspecified) 482 Loop detected VA_11 25 (Exchange routing error) 483 Too many hops VA_12 1 (Unallocated (unassigned) number) 485 Ambiguous VA_13 50 (requested facility no subscribed) 488 Not acceptable here VA_14 127 (interworking unspecified) 500 Server Internal error VA_15 79 (service or option not implemented) 501 Not implemented VA_16 27 (Destination out of order) 502 Bad Gateway VA_17 102 (Recovery on timer expiry) 504 Server timeout VA_18 21 (Call rejected) 603 Decline VA_19 2 (No route to specified transit network) 604 Does not exist anywhere VA_20 88 (incompatible destination) 606 Not acceptable


TSS reference SIP-I - SIP NNI/Basic call/Receipt_of_4xx-5xx-6xx/ Selection criteria Test Purpose name Mapping of Reason header into Cause value of REL Test Purpose Ensure that on receipt of an unsuccessful final response SIP_Response and a Reason

header is present set to cause SIP_cause, this value is used in the corresponding REL message. The mapping is indicated in table 6.1.2.7-3. The location value in the REL message is set to 'network beyond interworking point'

ISUP Parameter values REL: Cause= SIP_cause SIP Parameter values SIP_Response: Reason: cause= SIP_cause Comments The use of different cause values in the Reason header is recommended. The cause value

should be adequate to the response code. Message flows SIP-I MGCF SIP NNI


ETSI

ETSI TS 101 572-2 V1.2.1 (2014-07)157


SIP_Response_VA ←REL (cause code) SIP_cause


VA_01 SIP_cause 400 Bad Request VA_02 SIP_cause 401 Unauthorized VA_03 SIP_cause 402 Payment Required VA_04 SIP_cause 403 Forbidden VA_05 SIP_cause 404 Not Found VA_06 SIP_cause 405 Method Not Allowed VA_07 SIP_cause 406 Not Acceptable VA_08 SIP_cause 407 Proxy authentication required VA_09 SIP_cause 408 Request Timeout VA_10 SIP_cause 410 Gone VA_11 SIP_cause 413 Request Entity too long VA_12 SIP_cause 414 Request-URI too long VA_13 SIP_cause 415 Unsupported Media type VA_14 SIP_cause 416 Unsupported URI scheme VA_15 SIP_cause 417 Unknown Resource-Priority VA_16 SIP_cause 420 Bad Extension VA_17 SIP_cause 421 Extension required VA_18 SIP_cause 422 Session Interval Too Small VA_19 SIP_cause 423 Interval Too Brief VA_20 SIP_cause 433 Anonymity Disallowed. VA_21 SIP_cause 440 Max-Breadth Exceeded VA_22 SIP_cause 480 Temporarily Unavailable VA_23 SIP_cause 481 Call/Transaction does not exist VA_24 SIP_cause 482 Loop detected VA_25 SIP_cause 483 Too many hops VA_26 SIP_cause 484 Address Incomplete VA_27 SIP_cause 485 Ambiguous VA_28 SIP_cause 486 Busy Here VA_29 SIP_cause 487 Request terminated VA_30 SIP_cause 488 Not acceptable here VA_31 SIP_cause 493 Undecipherable VA_32 SIP_cause 500 Server Internal error VA_33 SIP_cause 501 Not implemented VA_34 SIP_cause 502 Bad Gateway VA_35 SIP_cause 503 Service Unavailable VA_36 SIP_cause 504 Server timeout VA_37 SIP_cause 505 Version not supported VA_38 SIP_cause 513 Message too large VA_39 SIP_cause 580 Precondition failure VA_40 SIP_cause 600 Busy Everywhere VA_41 SIP_cause 603 Decline VA_42 SIP_cause 604 Does not exist anywhere VA_43 SIP_cause 606 Not acceptable

ETSI

ETSI TS 101 572-2 V1.2.1 (2014-07)158


TSS reference SIP-I - SIP NNI/Basic call/Receipt_of_4xx-5xx-6xx/ Selection criteria PICS 6.2.1/5 Test Purpose name Mapping of PSTN XML ProgressIndicator 1 in an unsuccessful final response into ATP in

the REL Test Purpose Ensure that on receipt of a PSTN XML ProgressIndicator value 1 in an unsuccessful final

response as indicated in table 6.1.2.7-4, a SIP_Response with encapsulated REL is sent and an Access Transport Parameter is present containing a Progress Indicator #1

ISUP Parameter values REL: Access Transport Progress Indicator Progress Description='0000001'

SIP Parameter values SIP_Response: <?xml version="1.0" encoding="utf-8"?> PSTN ProgressIndicator ProgressOctet4 ProgressDescription>0000001<


INVITE (IAM) � � INVITE 100 Trying � � 100 Trying SIP_Response (REL) � � SIP_Response ACK (RLC) � � ACK

TP number TP_207_007 Reference [1], clauses 7.2.1, 7.3.1 [2], clause 7.2.3.2.12







IAM � � INVITE � 100 Trying SIP_Response (REL) � � SIP_Response ACK (RLC) � � ACK

ETSI

ETSI TS 101 572-2 V1.2.1 (2014-07)159













ISUP Parameter values IAM: USI=speech or 3,1 kHz audio, USI prime=unrestricted digital info with T/A, TMR=64 kbit/s preferred, TMR prime = speech or 3,1 kHz audio REL: Access Transport Progress Indicator Progress Description='0000101'




ETSI

ETSI TS 101 572-2 V1.2.1 (2014-07)160


SIP_Response_VA ←4xx/5xx/6xx SIP Message SIP_Response

VA_01 400 Bad Request VA_02 403 Forbidden VA_03 406 Not Acceptable VA_04 408 Request Timeout VA_05 410 Gone VA_06 480 Temporarily Unavailable VA_07 488 Not acceptable here VA_08 500 Server Internal error VA_09 502 Bad Gateway VA_10 504 Server timeout VA_11 603 Decline VA_12 606 Not acceptable


TSS reference SIP-I - SIP NNI/Basic call/Receipt_of_4xx-5xx-6xx/ Selection criteria PICS 6.2.1/5 Test Purpose name Mapping of PSTN XML HighLayerCompatibility in an unsuccessful final response into ATP

in REL Test Purpose Ensure that on receipt of an unsuccessful final response and a PSTN XML

HighLayerCompatibility element is present a SIP_Response as indicated in table 6.1.2.7-4 with encapsulated REL is sent and a Access Transport Parameter is present containing a High layer compatibility IE and the value is set to the value HLC_VA as indicated in table 6.1.2.5-1

ISUP Parameter values REL: Access Transport High layer compatibility High layer characteristics identification = HLC_VA

SIP Parameter values SIP_Response: PSTN XML MIME body <?xml version="1.0" encoding="utf-8"?> PSTN HighLayerCompatibility HLOctet3 CodingStandard>00< Interpretation>100< PresentationMethod>01< HLOctet4 HighLayerCharacteristics>HLC_VA<



ETSI

ETSI TS 101 572-2 V1.2.1 (2014-07)161


TSS reference SIP-I - SIP NNI/Basic call/Receipt_of_4xx-5xx-6xx/ Selection criteria PICS 6.2.1/5 Test Purpose name Mapping of PSTN XML BearerCapability in an unsuccessful final response into ATP in REL Test Purpose Ensure that on receipt of an unsuccessful final response and a PSTN XML

BearerCapability element is present, a SIP_Response as indicated in table 6.1.2.7-4 with encapsulated REL is sent and a Access Transport Parameter is present containing a Bearer Capability IE and the value is set to the value ITC_value as indicated in table 6.1.2.5-2

ISUP Parameter values REL: Access Transport Bearer Capability Information Transfer Capability = ITC_value

SIP Parameter values SIP_Response: <?xml version="1.0" encoding="utf-8"?> PSTN BearerCapability BCoctet3 CodingStandard>00< InformationTransferCapability> ITC_value < BCoctet4 TransferMode>00< InformationTransferRate>10000<




TSS reference SIP-I - SIP NNI/Basic call/Receipt_of_4xx-5xx-6xx/ Selection criteria PICS 6.2.1/20 Test Purpose name Play media provided in an Error-Info header received in an unsuccessful final response Test Purpose Ensure that the SUT instructs the MGW to play out media associated with an URL present

in an Error-Info header received in an unsuccessful final response as indicated in table 6.1.2.7-4

ISUP Parameter values SIP Parameter values SIP_Response: Error-Info: <Media re source URL> Comments Message flows SIP-I MGCF ISUP

INVITE (IAM) � � INVITE 100 Trying � � 100 Trying � SIP_Response 183 Session Progress � ACK

The MGC plays media SIP_Response � ACK �



ETSI

ETSI TS 101 572-2 V1.2.1 (2014-07)162

TP number TP_207_015 Reference [1], clause 7.3.1 [2], clauses 7.2, 7.2.3.2.1

TSS reference SIP-I - SIP NNI/Basic call/Receipt_of_4xx-5xx-6xx/ Selection criteria PICS 6.2.1/3 Test Purpose name 580 response to an UPDATE within an early dialog Test Purpose Ensure that on receipt of a 580 Precondition Failure final response after an UPDATE

request was sent in the early dialogue, a REL is sent and the Cause value is set to 127 ISUP Parameter values IAM: Nature of connection indicator= continuity check required on this circuit or continuity

check performed on previous circuit COT: Continuity indicator=continuity check successful REL: Cause=127

SIP Parameter values INVITE: Supported: precondition, 100rel SDP a=curr:qos local none a=curr:qos remote none a=des:qos mandatory local sendrecv a=des:qos none remote sendrecv 183: Require: 100rel SDP a=curr:qos local none a=curr:qos remote none a=des:qos mandatory local sendrecv a=des:qos mandatory remote sendrecv a=conf:qos remote sendrecv UPDATE: SDP a=curr:qos local sendrecv a=curr:qos remote none a=des:qos mandatory local sendrecv a=des:qos mandatory remote sendrecv


INVITE (IAM) � � INVITE 100 Trying � � 100 Trying 183 Session Progress � � 183 Session Progress PRACK � � PRACK 200 OK (PRACK) � � 200 OK (PRACK) UPDATE � � UPDATE 580 Precondition Failure (REL)

� � 580 Precondition Failure

ACK (RLC) � � ACK Apply post test routine

ETSI

ETSI TS 101 572-2 V1.2.1 (2014-07)163

6.1.2.8 Receipt of a BYE


TSS reference SIP-I - SIP NNI/Basic call/Receipt_of_BYE/ Selection criteria Test Purpose name BYE received, REL is sent Test Purpose Ensure that on receipt of a BYE message and no reason header is present, a BYE with

encapsulated REL is sent. The Cause value of the REL is set to #16, the location is set to 'network beyond interworking point'



� � 180 Ringing



ACK � � ACK BYE (REL) � � BYE 200 OK (BYE) RLC

� � 200 OK (BYE)


TSS reference SIP-I - SIP NNI/Basic call/Receipt_of_BYE/ Selection criteria Test Purpose name BYE received a Reason header is present, REL Cause derived from the Reason cause

value Test Purpose Ensure that on receipt of a BYE request and a Reason header is present, a BYE with

encapsulated REL is sent. The Cause parameter is derived from cause parameter in the Reason header

ISUP Parameter values REL: Cause=<Reason cause> SIP Parameter values BYE: Reason: cause Comments Message flows SIP-I MGCF SIP NNI

INVITE (IAM) � � INVITE � 100 Trying 180 Ringing (ACM free)

� � 180 Ringing

ANM (200 OK) INVITE � � 200 OK (INVITE) ACK � ACK BYE (REL) � � BYE 200 OK (BYE) (RLC) � � 200 OK (BYE)

ETSI

ETSI TS 101 572-2 V1.2.1 (2014-07)164


TSS reference SIP-I - SIP NNI/Basic call/Receipt_of_BYE/ Selection criteria PICS 6.2.1/5 Test Purpose name Mapping of PSTN XML ProgressIndicator 1 in a BYE into ATP in the REL Test Purpose Ensure that on receipt of a PSTN XML ProgressIndicator value 1 in a BYE request, a BYE

with encapsulated REL is sent and an Access Transport Parameter is present containing a Progress Indicator #1


SIP Parameter values BYE: <?xml version="1.0" encoding="utf-8"?> PSTN ProgressIndicator ProgressOctet4 ProgressDescription>0000001<



� � 180 Ringing



ACK � � ACK BYE (REL) � � BYE 200 OK (BYE) (RLC) � � 200 OK (BYE)







INVITE (IAM) � � INVITE � 100 Trying 180 Ringing (ACM - free)

� � 180 Ringing



ACK � � ACK BYE (REL) � � BYE 200 OK (BYE) (RLC)

� � 200 OK (BYE)

ETSI

ETSI TS 101 572-2 V1.2.1 (2014-07)165













ISUP Parameter values IAM: USI=speech or 3,1 kHz audio, USI prime=unrestricted digital info with T/A, TMR=64 kbit/s preferred, TMR prime = speech or 3,1 kHz audio REL: Access Transport Progress Indicator Progress Description='0000101'



IAM � � INVITE � 100 Trying 180 Ringing (ACM – free)

� � 180 Ringing




ETSI

ETSI TS 101 572-2 V1.2.1 (2014-07)166


TSS reference SIP-I - SIP NNI/Basic call/Receipt_of_BYE/ Selection criteria PICS 6.2.1/5 Test Purpose name Mapping of PSTN XML HighLayerCompatibility in a BYE into ATP in REL Test Purpose Ensure that on receipt of BYE request and a PSTN XML HighLayerCompatibility element is

present a BYE with encapsulated REL is sent and a Access Transport Parameter is present containing a High layer compatibility IE and the value is set to the value HLC_VA as indicated in table 6.1.2.5-1


SIP Parameter values BYE: PSTN XML MIME body <?xml version="1.0" encoding="utf-8"?> PSTN HighLayerCompatibility HLOctet3 CodingStandard>00< Interpretation>100< PresentationMethod>01< HLOctet4 HighLayerCharacteristics>HLC_VA<


INVITE (IAM) � � INVITE � 100 Trying 180 Ringing (ACM)

� � 180 Ringing




ETSI

ETSI TS 101 572-2 V1.2.1 (2014-07)167


TSS reference SIP-I - SIP NNI/Basic call/Receipt_of_BYE/ Selection criteria PICS 6.2.1/5 Test Purpose name Mapping of PSTN XML BearerCapability in a BYE into ATP in REL Test Purpose Ensure that on receipt of a BYE request and a PSTN XML BearerCapability element is

present, a BYE with encapsulated REL is sent and a Access Transport Parameter is present containing a Bearer Capability IE and the value is set to the value ITC_value as indicated in table 6.1.2.5-2


SIP Parameter values BYE: <?xml version="1.0" encoding="utf-8"?> PSTN BearerCapability BCoctet3 CodingStandard>00< InformationTransferCapability> ITC_value < BCoctet4 TransferMode>00< InformationTransferRate>10000<


IAM � � INVITE � 100 Trying 180 Ringing (ACM – free)

� � 180 Ringing



ACK � � ACK BYE (REL) � � BYE 200 OK (BYE) (RLC)

� � 200 OK (BYE)

6.1.2.9 Receipt of the Release Message


TSS reference SIP-I - SIP NNI/Basic call/Receipt_of_REL/ Selection criteria Test Purpose name REL received before an early dialogue was established, a CANCEL is sent Test Purpose Ensure that on receipt of a CANCEL/BYE with encapsulated REL message before an early

dialogue was established, a CANCEL request is sent and the Reason header is present, the cause value is derived from the Cause value in the received REL

ISUP Parameter values REL: Cause value SIP Parameter values CANCEL: Reason: cause=<Cause value> Comments Message flows SIP-I MGCF SIP NNI

INVITE (IAM) � � INVITE 100 Trying � � 100 Trying CANCEL/BYE (REL) � � CANCEL 200 OK (CANCEL) (RLC) � � 200 OK (CANCEL) 487 Request Terminated � � 487 Request Terminated ACK � � ACK

ETSI

ETSI TS 101 572-2 V1.2.1 (2014-07)168


TSS reference SIP-I - SIP NNI/Basic call/Receipt_of_REL/ Selection criteria Test Purpose name REL received after an early dialogue with 180 was established, a CANCEL is sent Test Purpose Ensure that on receipt of a CANCEL/BYE with encapsulated REL message after an early

dialogue due to a 180 Ringing response was established, a CANCEL request is sent and the Reason header is present, the cause value is derived from the Cause value in the received REL


INVITE (IAM) � � INVITE � 100 Trying 180 Ringing (ACM – free) � � 180 Ringing CANCEL/BYE (REL) � � CANCEL 200 OK (CANCEL) (RLC) � � 200 OK (CANCEL) 487 Request Terminated � � 487 Request Terminated ACK � � ACK



dialogue due to a 181 Call is Being Forwarded response was established, a CANCEL request is sent and the Reason header is present, the cause value is derived from the Cause value in the received REL


INVITE (IAM) � � INVITE � 100 Trying 181 Being forwarded (ACM) � � 181 Being forwarded CANCEL/BYE (REL) � � CANCEL 200 OK (CANCEL) (RLC) � � 200 OK (CANCEL) 487 Request Terminated � � 487 Request Terminated ACK � � ACK

ETSI

ETSI TS 101 572-2 V1.2.1 (2014-07)169


TSS reference SIP-I - SIP NNI/Basic call/Receipt_of_REL/ Selection criteria Test Purpose name Test Purpose REL received after an early dialogue with 182 was established, a CANCEL is sent ISUP Parameter values Ensure that on receipt of a CANCEL/BYE with encapsulated REL message after an early

dialogue due to a 182 Queued response was established, a CANCEL request is sent and the Reason header is present, the cause value is derived from the Cause value in the received REL

SIP Parameter values REL: Cause value Comments CANCEL: Reason: cause=<Cause value> Message flows SIP-I MGCF SIP NNI

INVITE (IAM) � � INVITE � � 100 Trying 182 Queued (ACM) � � 182 Queued CANCEL/BYE (REL) � � CANCEL 200 OK (CANCEL) (RLC) � � 200 OK (CANCEL) 487 Request Terminated � � 487 Request Terminated ACK � � ACK



dialogue due to a 183 Session Progress response was established, a CANCEL request is sent and the Reason header is present, the cause value is derived from the Cause value in the received REL


INVITE (IAM) � � INVITE 100 Trying � � 100 Trying 183 Session Progress (ACM) � � 183 Session Progress CANCEL/BYE (REL) � � CANCEL 200 OK (CANCEL) (RLC) � � 200 OK (CANCEL) 487 Request Terminated � � 487 Request Terminated ACK � � ACK

ETSI

ETSI TS 101 572-2 V1.2.1 (2014-07)170


TSS reference SIP-I - SIP NNI/Basic call/Receipt_of_REL/ Selection criteria Test Purpose name REL received in the confirmed dialogue a BYE is sent Test Purpose Ensure that on receipt of a BYE with encapsulated REL message in the confirmed

dialogue, a BYE request is sent and the Reason header is present, the cause value is derived from the Cause value in the received REL

ISUP Parameter values REL: Cause value SIP Parameter values BYE: Reason: cause=<Cause value> Comments Message flows SIP-I MGCF IP NNI

INVITE (IAM) � � INVITE 100 Trying � � 100 Trying 180 Ringing (ACM – free) � � 180 Ringing 200 OK (INVITE) (ANM) � � 200 OK (INVITE) ACK � � ACK BYE (REL) � � BYE 200 OK (BYE) (RLC) � � 200 OK (BYE)


TSS reference SIP-I - SIP NNI/Basic call/Receipt_of_REL/ Selection criteria PICS 6.2.1/5 Test Purpose name Mapping of REL ATP Progress Indicator #1 into PSTN XML ProgressIndicator #1 in the

BYE Test Purpose Ensure that on receipt of a BYE with encapsulated REL message and a ATP containing a

Progress Indicator #2 in the confirmed dialogue, a BYE request is sent and a PSTN XML ProgressIndicator is present, the ProgressDescription is set to #1



Comments Message flows SIP NNISIP-I MGCF SIP NNI

INVITE (IAM) � � INVITE � 100 Trying 180 Ringing (ACM) � � 180 Ringing 200 OK (INVITE) (ANM) � � 200 OK (INVITE) ACK � � ACK BYE (REL) � � BYE 200 OK (BYE) (RLC) � � 200 OK (BYE)

ETSI

ETSI TS 101 572-2 V1.2.1 (2014-07)171








INVITE (IAM) � � INVITE � 100 Trying 180 Ringing (ACM – free) � � 180 Ringing 200 OK (INVITE) (ANM) � � 200 OK (INVITE) ACK � � ACK BYE (REL) � � BYE 200 OK (BYE) (RLC) � � 200 OK (BYE)








INVITE (IAM) � � INVITE � 100 Trying 180 Ringing (ACM) � � 180 Ringing 200 OK (ANM) � � 200 OK (INVITE) ACK � � ACK BYE (REL) � � BYE 200 OK (BYE) (RLC) � � 200 OK (BYE)

ETSI

ETSI TS 101 572-2 V1.2.1 (2014-07)172



BYE Test Purpose Ensure that on receipt of a BYE with encapsulated REL message and an ATP containing a




Comments Message flows MGCF SIP NNI

INVITE (IAM) � � INVITE � 100 Trying 180 Ringing (ACM) � � 180 Ringing 200 OK (INVITE)(ANM) � � 200 OK (INVITE) ACK � � ACK BYE (REL) � � BYE 200 OK (BYE) (RLC) � � 200 OK (BYE)


TSS reference SIP-I - SIP NNI/Basic call/Receipt_of_REL/ Selection criteria PICS 6.2.1/5 Test Purpose name Mapping of REL ATP High layer compatibility into PSTN XML HighLayerCompatibility in

the BYE Test Purpose Ensure that on receipt of a BYE with encapsulated REL message and an ATP containing a

High layer compatibility IE in the confirmed dialogue, a BYE request is sent and a PSTN XML HighLayerCompatibility is present, the HighLayerCharacteristics is set to HLC_VA as indicated in table 6.1.2.1-4


SIP Parameter values BYE: PSTN XML MIME body <?xml version="1.0" encoding="utf-8"?> PSTN HighLayerCompatibility HLOctet3 CodingStandard>00< Interpretation>100< PresentationMethod>01< HLOctet4 HighLayerCharacteristics>HLC_VA<


INVITE (IAM) � � INVITE � 100 Trying 180 Ringing (ACM – free) � � 180 Ringing 200 OK (INVITE) (ANM) � � 200 OK (INVITE) ACK � � ACK BYE (REL) � � BYE 200 OK (BYE) (RLC) � � 200 OK (BYE)

ETSI

ETSI TS 101 572-2 V1.2.1 (2014-07)173


TSS reference SIP-I - SIP NNI/Basic call/Receipt_of_REL/ Selection criteria PICS 6.2.1/5 Test Purpose name Mapping of REL ATP Bearer Capability into PSTN XML Bearer Capability in the BYE Test Purpose Ensure that on receipt of a BYE with encapsulated REL message and an ATP containing a

Bearer Capability IE in the confirmed dialogue, a BYE request is sent and a PSTN XML Bearer Capability is present, the InformationTransferCapability is set to ITC_value as indicated in table 6.1.2.1-6


SIP Parameter values BYE: <?xml version="1.0" encoding="utf-8"?> PSTN BearerCapability BCoctet3 CodingStandard>00< InformationTransferCapability>ITC_value< BCoctet4 TransferMode>00< InformationTransferRate>10000<


INVITE (IAM) � � INVITE 100 Trying � � 100 Trying 180 Ringing (ACM) � � 180 Ringing 200 OK (INVITE) (ANM) � � 200 OK (INVITE) ACK � � ACK BYE (REL) � � BYE 200 OK (BYE) (RLC) � � 200 OK (BYE)

6.1.2.10 Void

6.1.2.11 Autonomous Release at O-MGCF


TSS reference SIP-I - SIP NNI/Basic call/Autonomous_Release/ Selection criteria Test Purpose name Call is released to due message compatibility instruction 'Release call' received in the early

dialogue Test Purpose Ensure that on receipt of an unknown ISUP message in the early dialogue and the

message compatibility is set to 'release call' an ISUP REL message is sent and the Cause indicator is set to value 97. In addition a SIP CANCEL request is sent and a Reason header field is present

ISUP Parameter values ??? = unknown message: Message compatibility information: Release call indicator=release call REL: Cause=97

SIP Parameter values CANCEL: Reason: Comments For an unknown message use a message type unknown in the SUT. Message flows SIP-I MGCF SIP NNI


� � 180 Ringing

INFO(???) � 500 Server Internal Error (REL#97) � � CANCEL ACK (RLC) � � 200 OK (CANCEL) � 487 Request Terminated � ACK

ETSI

ETSI TS 101 572-2 V1.2.1 (2014-07)174


TSS reference SIP-I - SIP NNI/Basic call/Autonomous_Release/ Selection criteria Test Purpose name Call is released to due message compatibility instruction 'Release call' received in the

confirmed dialogue Test Purpose Ensure that on receipt of an unknown ISUP message in the confirmed dialogue and the

message compatibility is set to 'release call' an ISUP REL message is sent and the Cause indicator is set to value 97. In addition a SIP BYE request is sent and a Reason header field is present

ISUP Parameter values ??? = unknown message: Message compatibility information: Release call indicator=release call REL: Cause=97

SIP Parameter values BYE: Reason: Comments For an unknown message use a message type unknown in the SUT. Message flows SIP NNISIP-I MGCF ISUP


� � 180 Ringing

200 OK (INVITE) � � 200 OK (INVITE) ACK � � ACK INFO(???) � BYE (REL#97) � � BYE 200 OK BYE (RLC) � � 200 OK (BYE)


TSS reference SIP-I - SIP NNI/Basic call/Autonomous_Release/ Selection criteria Test Purpose name Call is released to due parameter compatibility instruction 'Release call' received in the

early dialogue Test Purpose Ensure that on receipt of a CPG in the early dialogue and an unknown parameter is

present the parameter compatibility instruction is set to 'release call' an ISUP REL message is sent and the Cause indicator is set to value 99 or 110. In addition a SIP CANCEL request is sent and a Reason header field is present.

ISUP Parameter values CPG: Parameter compatibility information: Release call indicator=release call REL: Cause=99 or 110

SIP Parameter values CANCEL: Reason: Comments For an unknown parameter use a parameter type unknown in the SUT. Message flows SIP NNISIP-I MGCF ISUP

INVITE (IAM) � � INVITE 180 Ringing (ACM –free)

� � 180 Ringing

183 Session Progress (CPG) � 500 Server Internal Error (REL#99/110) � � CANCEL ACK (RLC) � � 200 OK (CANCEL) � 487 Request Terminated � ACK

ETSI

ETSI TS 101 572-2 V1.2.1 (2014-07)175


TSS reference SIP-I - SIP NNI/Basic call/Autonomous_Release/ Selection criteria Test Purpose name Call is released to due parameter compatibility instruction 'Release call' received in the

confirmed dialogue Test Purpose Ensure that on receipt of a CPG in the confirmed dialogue and an unknown parameter is

present the parameter compatibility instruction is set to 'release call' an ISUP REL message is sent and the Cause indicator is set to value 99 or 110. In addition a SIP BYE request is sent and a Reason header field is present

ISUP Parameter values CPG: Parameter compatibility information: Release call indicator=release call REL: Cause=99 or 110

SIP Parameter values BYE: Reason: Comments For an unknown parameter use a parameter type unknown in the SUT. Message flows SIP NNI MGCF SIP-I

INVITE (IAM) � � INVITE 180 Ringing (ACM - free)

� � 180 Ringing



ACK � � ACK INFO (CPG – conference established)

�

BYE (REL# 99 or 110) � � BYE 200 OK (BYE) (RLC)

� � 200 OK (BYE)

6.2 Supplementary Services

6.2.1 Void

6.2.2 Connected line presentation and restriction (COLP/COLR)

TP number TP_302_001 Reference [1], clause 7.2.1 [2], clause 7.4.2

TSS reference PSTN-SS/COL/ Selection criteria NOT PICS 6.3.4/1 AND PICS 6.3.1/1 AND PICS 6.3.2/2 Test Purpose name The SUT does not invoke the COLP service Test Purpose Ensure that on receipt of an INVITE request ant the SUT does not invoke the COLP

service, an INVITE with encapsulated IAM is sent and the Connected Line Identity Request indicator field of the Optional forward call indicators parameter of the IAM to 'not requested'. A received connected number is not interworked

ISUP Parameter values IAM: Optional forward call indicators = 'COL not requested' ANM/CON: Connected number present

SIP Parameter values 200 OK: P-Asserted-Identity not present Comments Message flows SIP-NNI MGCF SIP-I

INVITE � � INVITE (IAM) 100 Trying � CASE A 180 Ringing � � 180 Ringing (ACM – free) 200 OK (INVITE) � � 200 OK (INVITE) (ANM) ACK � � ACK CASE B 200 OK (INVITE) � � 200 OK (CON) ACK � � ACK


ETSI

ETSI TS 101 572-2 V1.2.1 (2014-07)176


TSS reference PSTN-SS/COL/ Selection criteria PICS 6.3.4/1 AND PICS 6.3.1/1 AND PICS 6.3.2/2 Test Purpose name The SUT invokes the COLP service presentation allowed Test Purpose Ensure that on receipt of an INVITE request ant the SUT invokes the COLP service, an

INVITE with encapsulated IAM is sent and the Connected Line Identity Request indicator field of the Optional forward call indicators parameter of the IAM to 'requested'. A received connected number presentation allowed is interworked. Connected number Nature of Address Indicator equal to - 'national (significant) number'

200 OK INVITE P-Asserted-Identity Add CC (of the country where the SUT is located) to Connected number address signals to construct an E.164 number in the URI. Prefix number with '+' in the format '+ CC NDC SN.'

- 'international number' 200 OK INVITE P-Asserted-Identity Map complete Connected number address signals to construct an E.164 number in the URI. Prefix number with "+" in the Format '+ CC NDC SN'.

Address presentation restriction indicator - 'presentation allowed'

Privacy header is not present or if present the value is not equal to 'id' ISUP Parameter values IAM: Optional forward call indicators = 'COL not requested'

ANM/CON: Connected number present SIP Parameter values INVITE: P-Asserted-Identity present

200 OK: P-Asserted-Identity present Comments Message flows SIP NNI MGCF SIP-I

INVITE � � INVITE (IAM) 100 Trying � CASE A 180 Ringing � � 180 Ringing (ACM – free) 200 OK (INVITE) � � 200 OK (INVITE) (ANM) ACK � � ACK CASE B 200 OK (INVITE) � � 200 OK (INVITE) (CON) ACK � � ACK


ETSI

ETSI TS 101 572-2 V1.2.1 (2014-07)177


TSS reference PSTN-SS/COL/ Selection criteria PICS 6.3.4/1 AND PICS 6.3.1/1 AND PICS 6.3.2/2 Test Purpose name The SUT invokes the COLP service presentation restricted Test Purpose Ensure that on receipt of an INVITE request ant the SUT invokes the COLP service, an

INVITE with encapsulated IAM is sent and the Connected Line Identity Request indicator field of the Optional forward call indicators parameter of the IAM to 'requested'. A received connected number presentation restricted is interworked Connected number Nature of Address Indicator equal to - 'national (significant) number'

200 OK INVITE P-Asserted-Identity Add CC (of the country where the SUT is located) to Connected number address signals to construct an E.164 number in the URI. Prefix number with '+' in the format '+ CC NDC SN.'

- 'international number' 200 OK INVITE P-Asserted-Identity Map complete Connected number address signals to construct an E.164 number in the URI. Prefix number with "+" in the Format '+ CC NDC SN'.

Address presentation restriction indicator - 'presentation restricted'

Privacy: id ISUP Parameter values IAM: Optional forward call indicators = 'COL requested'

ANM/CON: Connected number present SIP Parameter values INVITE: P-Asserted-Identity present

200 OK: P-Asserted-Identity present Privacy: id


INVITE � � INVITE (IAM) 100 Trying � CASE A 180 Ringing � � 180 Ringing (ACM – free) 200 OK (INVITE) � � 200 OK (INVITE) (ANM) ACK � � ACK CASE B 200 OK (INVITE) � � 200 OK (INVITE) (CON) ACK � � ACK


ETSI

ETSI TS 101 572-2 V1.2.1 (2014-07)178


TSS reference PSTN-SS/COL/ Selection criteria PICS 6.3.1/1 AND PICS 6.3.2/2 Test Purpose name COL request is set to 'not requested' Test Purpose Ensure that on receipt of an IAM and the Connected Line Identity Request indicator in the

Optional Forward Call Indicators parameter is set to 'not requested', no P-Asserted-Identity received in a provisional or successful final response is present. No connected number is sent in a 200 OK (INVITE) with encapsulated ANM or CON.


INVITE (IAM) � � INVITE � 100 Trying CASE A 180 Ringing (ACM – free) � � 180 Ringing 200 OK (INVITE) (ANM) � � 200 OK (INVITE) ACK � � ACK CASE B 200 OK (INVITE) (CON) � � 200 OK (INVITE) ACK � � ACK



TSS reference PSTN-SS/COL/ Selection criteria PICS 6.3.1/1 AND PICS 6.3.2/2 Test Purpose name COL request is set to 'requested' Terminating identity received in a 180 response Test Purpose Ensure that on receipt of an INVITE with encapsulated IAM and the Connected Line

Identity Request indicator in the Optional Forward Call Indicators parameter is set to 'requested', the P-Asserted-Identity received in a provisional response is sent in the 200 OK (INVITE) with encapsulated ANM. Coding of Connected number parameter

Number incomplete indicator equal to 'Complete' Numbering Plan Indicator equal to 'ISDN/Telephony (Recommendation E.164)' Nature of Address Indicator

If CC encoded in the URI is equal to the CC of the country where MGCF is located AND the next BICC/ISUP node is located in the same country then set to "national (significant) number" else set to "international number"

Address Presentation Restricted Indicator derived from the Privacy header according the mapping as described in table 6.2.2-1

ISUP Parameter values IAM: Optional Forward Call Indicators Connected Line Identity Request = requested ANM: Connected number Presentation restriction Privacy_VA

SIP Parameter values 180: P-Asserted-Identity


INVITE (IAM) � � INVITE � 100 Trying 180 Ringing (ACM) � � 180 Ringing 200 OK (INVITE) (ANM) � � 200 OK (INVITE) ACK � � ACK


ETSI

ETSI TS 101 572-2 V1.2.1 (2014-07)179


TSS reference PSTN-SS/COL/ Selection criteria PICS 6.3.1/1 AND PICS 6.3.2/2 Test Purpose name COL request is set to 'requested' Terminating identity received in a 200 OK response Test Purpose Ensure that on receipt of an INVITE with encapsulated IAM and the Connected Line

Identity Request indicator in the Optional Forward Call Indicators parameter is set to 'requested', the P-Asserted-Identity received in a 200 OK response is sent in the 200 OK response with encapsulated ANM. Coding of Connected number parameter




ISUP Parameter values IAM: Optional Forward Call Indicators Connected Line Identity Request = requested ANM: Connected number Presentation restriction Privacy_VA



INVITE (IAM) � � INVITE � 100 Trying 180 Ringing (ACM – free) � � 180 Ringing 200 OK (INVITE) (ANM) � � 200 OK (INVITE) ACK � � ACK


ETSI

ETSI TS 101 572-2 V1.2.1 (2014-07)180


TSS reference PSTN-SS/COL/ Selection criteria PICS 6.3.1/1 AND PICS 6.3.2/2 Test Purpose name COL request is set to requested Terminating identity received in a 200 OK response Test Purpose Ensure that on receipt of an INVITE with encapsulated IAM and the Connected Line

Identity Request indicator in the Optional Forward Call Indicators parameter is set to 'requested', if no provisional response was received the P-Asserted-Identity received in a 200 OK response is sent in the 200 OK with encapsulated CON. Coding of Connected number parameter




ISUP Parameter values IAM: Optional Forward Call Indicators Connected Line Identity Request = requested CON: Connected number Presentation restriction Privacy_VA



INVITE (IAM) � � INVITE � 100 Trying 200 OK (INVITE) (CON) � � 200 OK (INVITE) ACK � � ACK Apply post test routine

Table 6.2.2-1: Mapping of Privacy value into Address presentation restriction indicator

Privacy_VA Privacy value Address Presentation Restricted Indicator Privacy_VA_01 Header Presentation restricted Privacy_VA_02 User Presentation restricted Privacy_VA_03 None Presentation allowed Privacy_VA_04 Id Presentation restricted Privacy_VA_05 Privacy header not present Presentation allowed

ETSI

ETSI TS 101 572-2 V1.2.1 (2014-07)181

6.2.3 Malicious call identification


TSS reference PSTN-SS/MCID/ Selection criteria PICS 6.3.1/1 AND PICS 6.3.2/3 Test Purpose name MCID request before ACM Test Purpose Ensure that a MCID request before an ACM received in an ISUP IDR is discarded without

disrupt the call setup procedure. The sending of an IRS is optional ISUP Parameter values SIP Parameter values Comments Message flows SIP NNI MGCF SIP-I

INVITE � � INVITE (IAM) 100 Trying � CASE A � 183 Session Progress (IDR) � INFO (IRS) CASE B � 183 Session Progress (IDR) No response



TSS reference PSTN-SS/MCID/ Selection criteria PICS 6.3.1/1 AND PICS 6.3.2/3 Test Purpose name MCID request after ACM Test Purpose Ensure that a MCID request after an ACM received in an ISUP IDR is discarded without

disrupt the call setup procedure. The sending of an IRS is optional ISUP Parameter values SIP Parameter values Comments Message flows SIP SIP-I MGCF SIP NNI

INVITE � � INVITE (IAM) 100 Trying � 180 Ringing � � 180 Ringing (ACM) CASE A � 183 Session Progress (IDR) � INFO (IRS) CASE B � 183 Session Progress (IDR) No response


ETSI

ETSI TS 101 572-2 V1.2.1 (2014-07)182

6.2.4 Subaddressing (SUB)


TSS reference PSTN-SS/SUB/ Selection criteria PICS 6.3.2/4 Test Purpose name isub parameter in the To header is mapped into Called party Subaddress Test Purpose Ensure that on receipt of an initial INVITE request, an INVITE with encapsulated IAM is

sent. The isub parameter present in the To header is mapped into the Called party Subaddress covered in an Access Transport parameter in the sent IAM. If the isub-encoding parameter is present, the values 'nsap-ia5', 'nsap-bcd' or 'nsap' are relevant for mapping Encoding of the Subaddress in the IAM: Type of Subaddress='NSAP' Subaddress digits derived from the uric of the isub parameter

ISUP Parameter values IAM: Access Transport Called party subaddress Type of Subaddress=NSAP Subaddress digits derived from the uric of the isub parameter

SIP Parameter values INVITE: To: isub uric Subaddress digits isub-encoding: Not present nsap-ia5 nsap-bcd nsap





TSS reference PSTN-SS/SUB/ Selection criteria PICS 6.3.2/4 Test Purpose name isub parameter in the To header is not mapped Test Purpose Ensure that on receipt of an initial INVITE request, an INVITE with encapsulated IAM is

sent. The isub parameter present in the To header is not mapped into the Called party Subaddress if the value of the isub-encoding parameter is other then 'nsap-ia5', 'nsap-bcd' or 'nsap'

ISUP Parameter values SIP Parameter values INVITE: To:

isub uric Subaddress digits isub-encoding: <any token>




ETSI

ETSI TS 101 572-2 V1.2.1 (2014-07)183


TSS reference PSTN-SS/SUB/ Selection criteria PICS 6.3.2/4 Test Purpose name isub parameter in the P-Asserted-Identity header is mapped into Calling party Subaddress Test Purpose Ensure that on receipt of an initial INVITE request, an INVITE with encapsulated IAM is

sent. The isub parameter present in the P-Asserted-Identity header is mapped into the Calling party Subaddress covered in an Access Transport parameter in the sent IAM. If the isub-encoding parameter is present, the values 'nsap-ia5', 'nsap-bcd' or 'nsap' are relevant for mapping Encoding of the Subaddress: Type of Subaddress='NSAP' Subaddress digits derived from the uric of the isub parameter

ISUP Parameter values IAM: Access Transport Calling party subaddress Type of Subaddress=NSAP Subaddress digits derived from the uric of the isub parameter

SIP Parameter values INVITE: P-Asserted-Identity: isub uric Subaddress digits isub-encoding: Not present nsap-ia5 nsap-bcd nsap

Comments Message flows SIP NNISIP-I MGCF SIP-I




TSS reference PSTN-SS/SUB/ Selection criteria PICS 6.3.2/4 Test Purpose name isub parameter in the P-Asserted-Identity header in the INVITE is not mapped Test Purpose Ensure that on receipt of an initial INVITE request, an INVITE with encapsulated IAM is

sent. The isub parameter present in the P-Asserted-Identity header is not mapped into the Calling party Subaddress if the value of the isub-encoding parameter is other then 'nsap-ia5', 'nsap-bcd' or 'nsap'

ISUP Parameter values SIP Parameter values INVITE: P-Asserted-Identity:

isub uric Subaddress digits isub-encoding: <any token>

Comments Message flows SIP NNISIP-I MGCF SIP-I



ETSI

ETSI TS 101 572-2 V1.2.1 (2014-07)184


TSS reference PSTN-SS/SUB/ Selection criteria PICS 6.3.2/4 Test Purpose name Connected party Subaddress in the ANM is mapped into the isub parameter in the

P-Asserted-Identity header in the 200 OK Test Purpose Ensure that on receipt of a 200 OK with encapsulated ANM message containing a

Connected party Subaddress parameter in an Access Transport parameter, a 200 OK (INVITE) is sent and the P-Asserted-Identity header contains an isub parameter, the uric value is derived from the Connected Subaddress digits of the Connected party subaddress digits

ISUP Parameter values ANM: Access Transport Connected party subaddress Type of Subaddress=NSAP Subaddress digits

SIP Parameter values 200 OK: P-Asserted-Identity: isub uric digits derived from the Connected party Subaddress digits


INVITE � � INVITE (IAM) 180 Ringing � � 180 Ringing

( ACM – free) 200 OK (INVITE) � � 200 OK (INVITE)

(ANM) ACK � � ACK



TSS reference PSTN-SS/SUB/ Selection criteria PICS 6.3.2/4 Test Purpose name Connected party Subaddress in the ANM is not mapped Test Purpose Ensure that on receipt of a 200 OK (INVITE) ANM message containing a Connected party

Subaddress parameter in an Access Transport parameter, a 200 OK (INVITE) is sent and the Connected party subaddress is not mapped if the Type of subaddress is not equal 'NSAP'

ISUP Parameter values ANM: Access Transport Connected party subaddress Type of Subaddress other then NSAP


INVITE � � INVITE (IAM) 180 Ringing � � 180 Ringing

(ACM – free) 200 OK (INVITE) � � 200 OK (INVITE) (ANM) ACK � � ACK


ETSI

ETSI TS 101 572-2 V1.2.1 (2014-07)185


TSS reference PSTN-SS/SUB/ Selection criteria PICS 6.3.2/4 Test Purpose name Mapping of Called Party subaddress in the IAM into isub parameter in the To header in the

INVITE Test Purpose Ensure that on receipt of an INVITE with encapsulated IAM containing a Called party

subaddress in the Access Transport parameter, an initial INVITE is sent. The Called party subaddress is mapped into an isub parameter present in the To header in the INVITE if the Type of number of the subaddress is set to 'NSAP', the isub-encoding parameter is set to 'nsap-ia5'.

ISUP Parameter values IAM: Access Transport Called party subaddress Type of Subaddress=NSAP Subaddress digits

SIP Parameter values INVITE: To: isub uric digits derived from the Called party Subaddress digits isub-encoding=nsap-ia5





TSS reference PSTN-SS/SUB/ Selection criteria PICS 6.3.2/4 Test Purpose name No mapping of Called Party subaddress in the IAM Test Purpose Ensure that on receipt of an INVITE with encapsulated IAM containing a Called party

subaddress in the Access Transport parameter, an initial INVITE is sent. The Called party subaddress is not mapped into an isub parameter present in the To header of the INVITE if the Type of number of the subaddress is not equal to 'NSAP'

ISUP Parameter values IAM: Access Transport Called party subaddress Type of Subaddress not NSAP Subaddress digits




ETSI

ETSI TS 101 572-2 V1.2.1 (2014-07)186


TSS reference PSTN-SS/SUB/ Selection criteria PICS 6.3.2/4 Test Purpose name Mapping of Calling Party subaddress in the IAM into isub parameter in the P-Asserted-

Identity header in the INVITE Test Purpose Ensure that on receipt of an INVITE with encapsulated IAM containing a Calling party

subaddress in the Access Transport parameter, an initial INVITE is sent. The Calling party subaddress is mapped into an isub parameter present in the P-Asserted-Identity header in the INVITE if the Type of number of the subaddress is equal to 'NSAP', the isub-encoding parameter is set to 'nsap-ia5'.

ISUP Parameter values IAM: Access Transport Calling party subaddress Type of Subaddress=NSAP Subaddress digits

SIP Parameter values INVITE: P-Asserted-Identity: isub uric digits derived from the Calling party Subaddress digits isub-encoding=nsap-ia5





TSS reference PSTN-SS/SUB/ Selection criteria PICS 6.3.2/4 Test Purpose name No mapping of Calling Party subaddress in the IAM Test Purpose Ensure that on receipt of an INVITE with encapsulated IAM containing a Calling party

subaddress in the Access Transport parameter, an initial INVITE is sent. The Calling party subaddress is not mapped into an isub parameter present in the P-Asserted-Identity header in the INVITE if the Type of number of the subaddress is not equal to 'NSAP'

ISUP Parameter values IAM: Access Transport Calling party subaddress Type of Subaddress not NSAP Subaddress digits




ETSI

ETSI TS 101 572-2 V1.2.1 (2014-07)187


TSS reference PSTN-SS/SUB/ Selection criteria PICS 6.3.2/4 Test Purpose name Mapping of isub parameter in the 200 OK into the Connected party subaddress in the ANM Test Purpose Ensure that on receipt of an isub parameter present in the P-Asserted-Identity in a 200 OK

(INVITE), a 200 OK (INVITE) with encapsulated ANM is sent and the received Subaddress is mapped in the Connected party subaddress present in the Access Transport parameter in the ANM. If the isub-encoding parameter is present, the values 'nsap-ia5', 'nsap-bcd' or 'nsap' are relevant for mapping

ISUP Parameter values ANM: Access Transport Connected party subaddress Type of Subaddress=NSAP Subaddress digits derived from the uric of the isub parameter

SIP Parameter values 200 OK: P-Asserted-Identity: isub uric Subaddress digits isub-encoding: Not present nsap-ia5 nsap-bcd nsap


INVITE (IAM) � � INVITE 180 Ringing (ACM - free)

� � 180 Ringing





TSS reference PSTN-SS/SUB/ Selection criteria PICS 6.3.2/4 Test Purpose name Mapping of isub parameter in the 200 OK into the Connected party subaddress in the ANM Test Purpose Ensure that on receipt of an isub parameter present in the P-Asserted-Identity in a 200 OK

(INVITE), an ANM is sent and the received Subaddress is not mapped in the Connected party subaddress present in the Access Transport parameter in the ANM If the isub-encoding parameter is present and the value is not equal to 'nsap-ia5', 'nsap-bcd' or 'nsap'

ISUP Parameter values SIP Parameter values 200 OK: P-Asserted-Identity:

isub isub-encoding: Not nsap-ia5, nsap-bcd, nsap


INVITE (IAM) � � INVITE 180 Ringing (ACM) � � 180 Ringing 200 OK (INVITE) (ANM)



ETSI

ETSI TS 101 572-2 V1.2.1 (2014-07)188

6.2.5 Call Forwarding Busy (CFB)/ Call Forwarding No Reply (CFNR) / Call Forwarding Unconditional (CFU)

Table 6.2.5-1: Void

Table 6.2.5-2: Void

Table 6.2.5-3: Void

Table 6.2.5-4: Void

Table 6.2.5-5: Void

Table 6.2.5-6: Void

Table 6.2.5-7: Void

Table 6.2.5-8: Void

Table 6.2.5-9: Void

Table 6.2.5-10: Void




















ETSI

ETSI TS 101 572-2 V1.2.1 (2014-07)189














TSS reference PSTN-SS/CDIV/ Selection criteria NOT PICS 6.3.2/5 Test Purpose name No mapping of Redirecting number, Original called number and Redirection Information Test Purpose Ensure that on receipt of an INVITE with encapsulated IAM containing a Redirecting

number parameter, a Original called number and a Redirection Information parameter Redirecting reason indicator is set to REAS_value as indicated in table 6.2.5-42, an INVITE request is sent and no History-Info header is present. The call setup is not disrupted

ISUP Parameter values IAM: Redirecting number Redirection Information Redirecting reason =REAS_value Original called number



Table 6.2.5-42: Value of Redirecting reason received in Redirection Information

REAS_value VA_01 Unknown VA_02 Unconditional VA_03 User Busy VA_04 Deflection immediate response VA_05 Mobile subscriber not reachable

ETSI

ETSI TS 101 572-2 V1.2.1 (2014-07)190

TP number TP_305_066 Reference [1], clause 7.2.1 [2], clauses 7.4.6.3.3, table, 7.4.6.3.3.1, table, 7.4.6.3.3.3

TSS reference PSTN-SS/CDIV/ Selection criteria NOT PICS 6.3.2/5 Test Purpose name No mapping of ACM Redirection number and Call diversion information Test Purpose Ensure that on receipt of a 180 Ringing with encapsulated ACM a Redirection number and

the Call diversion parameter the Redirecting reason is set to REAS_value as indicated in table 6.2.5-43 is present as an indication a call diversion occurred, a 180 Ringing is sent and no History-Info header is present. The call setup is not disrupted

ISUP Parameter values ACM/CPG: Generic notification=call is diverting Redirection number Call diversion information Redirecting reason =REAS_value


INVITE � � INVITE (IAM) CASE A 180 Ringing � � 180 Ringing (ACM) 181 Being forwarded � � 183 Session Progress (CPG) CASE B 181 Being forwarded � � 183 Session Progress (ACM)


Table 6.2.5-43: Value of Redirecting reason received in Call diversion information

CAUSE Redirecting_Reason REAS_value

VA_01 unknown VA_02 unconditional VA_03 User Busy VA_04 Deflection immediate response VA_05 Mobile subscriber not reachable

ETSI

ETSI TS 101 572-2 V1.2.1 (2014-07)191

6.2.6 Explicit Call Transfer (ECT)


TSS reference PSTN-SS/ECT/ Selection criteria PICS 6.3.2/6 Test Purpose name A session is retrieved when a notification 'call transfer, active' in a reINVITE with

encapsulated FAC was received and the session is on hold Test Purpose I-MGCF: A session is on hold. Ensure that on receipt of an reINVITE with encapsulated

FAC message and the Generic notification indicator is set to 'call transfer, active', a reINVITE is sent the a attribute in the SDP is set to 'sendrecv'

ISUP Parameter values FAC: Generic notification=transfer active SIP Parameter values INVITE 2 SDP a=sendonly

INVITE 3 SDP a=sendrecv Comments Message flows SIP NNI MGCF SIP-I

INVITE 1 � � INVITE (IAM) 100 Trying � 180 Ringing � � 180 Ringing (ACM) 200 OK (INVITE) � � 200 OK (INVITE) (ANM) ACK � � ACK INVITE 2 � � INVITE 2 (CPG(hold)) 200 OK (INVITE) � � 200 OK (INVITE) ACK � � ACK INVITE 3 � � INFO

(FAC(call transfer, active)) 200 OK (INVITE) � � 200 OK (INFO) ACK �



TSS reference PSTN-SS/ECT/ Selection criteria PICS 6.3.2/6 Test Purpose name A session is retrieved when a notification 'call transfer, alerting' in a reINVITE with

encapsulated FAC was received and the session is on hold Test Purpose I-MGCF: A session is on hold. Ensure that on receipt of an reINVITE with encapsulated

FAC message and the Generic notification indicator is set to 'call transfer, alerting', a reINVITE is sent the a attribute in the SDP is set to 'sendrecv'

ISUP Parameter values FAC: Generic notification=transfer alerting SIP Parameter values INVITE 2 SDP a=sendonly


INVITE 1 � � INVITE (IAM) 100 Trying � 180 Ringing � � 180 Ringing (ACM) 200 OK (INVITE) � � 200 OK (INVITE) (ANM) ACK � � ACK INVITE 2 � � INVITE 2 (CPG(hold)) 200 OK (INVITE) � 200 OK (INVITE) ACK � ACK INVITE 3 � � INFO

(FAC(call transfer, alerting) 200 OK (INVITE) � � 200 OK (INFO) ACK �


ETSI

ETSI TS 101 572-2 V1.2.1 (2014-07)192


TSS reference PSTN-SS/ECT/ Selection criteria PICS 6.3.2/6 Test Purpose name A session is retrieved when a notification 'call transfer, active' in a reINVITE with

encapsulated CPG was received and the session is on hold Test Purpose O-MGCF: A session is on hold. Ensure that on receipt of a reINVITE with encapsulated

CPG message and the Generic notification indicator is set to 'call transfer, active', a reINVITE is sent the a attribute in the SDP is set to 'sendrecv'

ISUP Parameter values CPG: Generic notification=transfer active SIP Parameter values INVITE 2 SDP a=sendonly


INVITE � � INVITE (IAM) 100 Trying � � 100 Trying 180 Ringing � � 180 Ringing (ACM) 200 OK (INVITE) � � 200 OK (INVITE) (ANM) ACK � � ACK INVITE 2 � � INVITE 2 (CPG(hold)) 200 OK (INVITE) � � 200 OK (INVITE) ACK � � ACK INVITE 3 � � INFO

(CPG(call transfer, active)) 200 OK (INVITE) � � 200 OK (INFO) ACK �



TSS reference PSTN-SS/ECT/ Selection criteria PICS 6.3.2/6 Test Purpose name A session is retrieved when a notification 'call transfer, alerting' in a reINVITE with

encapsulated CPG was received and the session is on hold Test Purpose O-MGCF: A session is on hold. Ensure that on receipt of a reINVITE with encapsulated

CPG message and the Generic notification indicator is set to 'call transfer, alerting', a reINVITE is sent the a attribute in the SDP is set to 'sendrecv'

ISUP Parameter values CPG: Generic notification=transfer alerting SIP Parameter values INVITE 2 SDP a=sendonly

INVITE 3 SDP a=sendrecv Comments Message flows SIP NNISIP-I MGCF SIP-I

INVITE � � INVITE (IAM) 100 Trying � � 100 Trying 180 Ringing � � 180 Ringing (ACM) 200 OK (INVITE) � � 200 OK (INVITE) (ANM) ACK � � ACK INVITE 2 � � INVITE 2 (CPG(hold)) 200 OK (INVITE) � � 200 OK (INVITE) ACK � � ACK INVITE 3 � � INFO

(CPG(call transfer, alerting)) 200 OK (INVITE) � � 200 OK (INFO) ACK �


ETSI

ETSI TS 101 572-2 V1.2.1 (2014-07)193


TSS reference PSTN-SS/ECT/ Selection criteria PICS 6.3.2/6 Test Purpose name reINVITE with encapsulated FAC with generic notification 'call transfer, active' received, no

mapping Test Purpose I-MGCF: Ensure that on receipt of a reINVITE with encapsulated FAC message and the

Generic notification indicator is coded as 'call transfer, active' and the session is not on hold, no mapping occurs on the SIP side

ISUP Parameter values FAC: Generic notification=transfer active SIP Parameter values Comments Message flows SIP NNI MGCF SIP-I

INVITE � � INVITE (IAM) 100 Trying � 180 Ringing � � 180 Ringing (ACM) 200 OK (INVITE) � � 200 OK (INVITE) (ANM) ACK � � ACK � INFO

FAC(call transfer, active) � 200 OK (INVITE)



TSS reference PSTN-SS/ECT/ Selection criteria PICS 6.3.2/6 Test Purpose name FAC with generic notification 'call transfer, alerting' received, no mapping Test Purpose I-MGCF: Ensure that on receipt of a reINVITE with encapsulated FAC message and the

Generic notification indicator is coded as 'call transfer, alerting' and the session is not on hold, no mapping occurs on the SIP side

ISUP Parameter values FAC: Generic notification=transfer alerting SIP Parameter values Comments Message flows SIP NNI MGCF SIP-I

INVITE � � INVITE (IAM) 100 Trying � � 100 Trying 180 Ringing � � 180 Ringing (ACM) 200 OK (INVITE) � � 200 OK (INVITE) (ANM) ACK � � ACK � INFO

FAC(call transfer, alerting) � 200 OK (INVITE)


ETSI

ETSI TS 101 572-2 V1.2.1 (2014-07)194


TSS reference PSTN-SS/ECT/ Selection criteria PICS 6.3.2/6 Test Purpose name reINVITE with encapsulated CPG with generic notification 'call transfer, active' received, no

mapping Test Purpose I-MGCF: Ensure that on receipt of a reINVITE with encapsulated CPG message and the

Generic notification indicator is coded as 'call transfer, active' and the session is not on hold, no mapping occurs on the SIP side

ISUP Parameter values CPG: Generic notification=transfer active SIP Parameter values Comments Message flows SIP NNI MGCF SIP-I

INVITE � � IAM 100 Trying � � 100 Trying 180 Ringing � � 180 Ringing (ACM) 200 OK (INVITE) � � 200 OK (INVITE) (ANM) � INFO

(CPG(call transfer, active) � 200 OK (INVITE)



TSS reference PSTN-SS/ECT/ Selection criteria PICS 6.3.2/6 Test Purpose name reINVITE with encapsulated CPG with generic notification 'call transfer, alerting' received,

no mapping Test Purpose I-MGCF: Ensure that on receipt of a reINVITE with encapsulated CPG message and the

Generic notification indicator is coded as 'call transfer, alerting' and the session is not on hold, no mapping occurs on the SIP side

ISUP Parameter values CPG: Generic notification=transfer alerting SIP Parameter values Comments Message flows SIP NNI MGCF SIP-I

INVITE � � INVITE (IAM) 100 Trying � � 100 Trying 180 Ringing � � ACM (180 Ringing) 200 OK (INVITE) � � 200 OK (INVITE) (ANM) ACK � � ACK � INFO (CPG(call transfer, alerting)) � 200 OK (INVITE)


ETSI

ETSI TS 101 572-2 V1.2.1 (2014-07)195

6.2.7 Void

6.2.8 Call Hold


TSS reference PSTN-SS/HOLD/ Selection criteria PICS 6.3.2/9 Test Purpose name Hold and Retrieve requested from the ISUP/SIP-I Test Purpose Ensure that on receipt of an INVITE or UPDATE with encapsulated CPG message and the

Generic notification is set to 'Remote hold' in the confirmed dialogue, an INVITE or UPDATE is sent. The media stream in the SDP is set to 'sendonly'. Ensure that on receipt of a CPG message and the Generic notification is set to 'Remote retrieval', an INVITE or UPDATE is sent. The media stream in the SDP is set to 'sendrecv'

ISUP Parameter values CPG: Generic notification Remote hold Remote retrieval

SIP Parameter values INVITE/UPDATE: SDP 1 a=sendonly SDP 2 a=sendrecv


Establish a confirmed dialogue CASE A INVITE(SDP 1 = sendonly) � � INVITE (SDP 1 =

sendonly) (CPG(hold)) 200 OK (INVITE) � � 200 OK (INVITE) ACK � � ACK CASE B UPDATE(SDP 1 = sendonly) � � UPDATE (SDP 1 =

sendonly) (CPG(hold)) 200 OK (UPDATE) � � 200 OK (UPDATE) CASE A INVITE(SDP 2 = sendrecv) � � INVITE(SDP 2 =

sendrecv) CPG(retrieve)

200 OK (INVITE)

�

�

200 OK (INVITE)

ACK � � ACK CASE B UPDATE(SDP 2 = sendrecv) � � UPDATE (SDP 2 =

sendrecv) CPG(retrieve)

200 OK (UPDATE) � � 200 OK (UPDATE) Apply post test routine

ETSI

ETSI TS 101 572-2 V1.2.1 (2014-07)196


TSS reference PSTN-SS/HOLD/ Selection criteria PICS 6.3.2/9 Test Purpose name Hold and Retrieve requested from SIP in reINVITE request Test Purpose Ensure that on receipt of an INVITE request in the confirmed dialogue and the media

stream in the SDP is set to 'sendonly', a INVITE with encapsulated CPG message is sent the Generic notification indicator is set to 'remote hold'. Ensure that on receipt of an INVITE request in the confirmed dialogue and the media stream in the SDP is set to 'sendrecv', a CPG message is sent the Generic notification indicator is set to 'remote retrieval'




Establish a confirmed dialogue INVITE(sendonly) � � INVITE(sendonly)

(CPG(hold)) 200 OK (INVITE) � � 200 OK (INVITE) ACK � � ACK INVITE(sendrecv) � � INVITE(sendrecv)

(CPG(retrieve)) 200 OK (INVITE) � � 200 OK (INVITE) ACK � � ACK



TSS reference PSTN-SS/HOLD/ Selection criteria PICS 6.3.2/9 Test Purpose name Hold and Retrieve requested from SIP in UPDATE request Test Purpose Ensure that on receipt of an UPDATE request in the confirmed dialogue and the media

stream in the SDP is set to 'sendonly', a UPDATE with encapsulated CPG message is sent the Generic notification indicator is set to 'remote hold'. Ensure that on receipt of an UPDATE request in the confirmed dialogue and the media stream in the SDP is set to 'sendrecv', a CPG message is sent the Generic notification indicator is set to 'remote retrieval'




Establish a confirmed dialogue UPDATE(sendonly) � � UPDATE(sendonly)

(CPG(hold)) 200 OK (UPDATE) � � 200 OK (UPDATE) ACK � � ACK UPDATE(sendrecv) � � UPDATE(sendrecv)

(CPG(retrieve)) 200 OK (UPDATE) � � 200 OK (UPDATE) ACK � � ACK


ETSI

ETSI TS 101 572-2 V1.2.1 (2014-07)197


TSS reference PSTN-SS/HOLD/ Selection criteria PICS 6.3.2/9 Test Purpose name Hold requested from both ends, session inactive sent Test Purpose Ensure that on receipt of a INVITE with encapsulated CPG message and the Generic

notification indicator is set to 'remote hold' und the session was set on hold before, an INVITE or UPDATE request is sent and the media stream is set to 'inactive'

ISUP Parameter values CPG: Generic notification Remote hold

SIP Parameter values INVITE/UPDATE: SDP 1 a=sendonly SDP 2 a=inactive


Establish a confirmed dialogue INVITE(SDP 1 = sendonly) � � CPG(hold) 200 OK (INVITE) � � 200 OK (INVITE) ACK � � ACK CASE A INVITE(SDP 2 = inactive) � � INVITE(SDP 2 =

inactive) (CPG(hold))

200 OK (INVITE) � � 200 OK (INVITE) ACK � � ACK CASE B UPDATE(SDP 2 = inactive) � � UPDATE(SDP 2 =

inactive) (CPG(hold)) 200 OK (UPDATE) � � 200 OK (UPDATE)


ETSI

ETSI TS 101 572-2 V1.2.1 (2014-07)198


TSS reference PSTN-SS/HOLD/ Selection criteria PICS 6.3.2/9 Test Purpose name Hold requested from both ends, session inactive received Test Purpose The session is already set on hold. Ensure that on receipt of an INVITE request and the

media stream in the SDP is set to 'inactive', a INVITE with encapsulated CPG message is sent and the Notification indicator is set to 'remote hold'


SIP Parameter values INVITE/UPDATE: SDP 1 a=sendonly SDP 2 a=inactive


Establish a confirmed dialogue CASE A INVITE(SDP 1 = sendonly) � � INVITE(SDP 1 =

sendonly) (CPG(hold)) 200 OK (INVITE) � � 200 OK (INVITE) ACK � � ACK CASE B UPDATE(SDP 1 = sendonly) � � UPDATE(SDP 1 =

sendonly) (CPG(hold)) 200 OK (UPDATE) � � 200 OK (UPDATE) INVITE(SDP 2 = inactive) � � INVITE(SDP 2 =

inactive) (CPG(hold)) 200 OK (INVITE) � � 200 OK (INVITE) ACK � � ACK


ETSI

ETSI TS 101 572-2 V1.2.1 (2014-07)199


TSS reference PSTN-SS/HOLD/ Selection criteria PICS 6.3.2/9 Test Purpose name First hold from SIP. Session inactive, Retrieve requested from SIP Test Purpose The session is set on hold at first from SIP as well as second from SIP-I . Ensure that on

receipt of an INVITE request and the media stream in the SDP is set to 'recvonly', a INVITE or UPDATE with encapsulated CPG message is sent and the Generic notification indicator is set to 'remote retrieval'

ISUP Parameter values CPG 1: Generic notification Remote hold CPG 2: Generic notification Remote retrieval

SIP Parameter values INVITE/UPDATE: SDP 1 a=sendonly SDP 2 a=inactive SDP 3 a=recvonly


Establish a confirmed dialogue INVITE(SDP 1 = sendonly) � � INVITE(SDP 1 =

sendonly) (CPG 1 (hold))

200 OK (INVITE) � � 200 OK (INVITE) ACK � � ACK CASE A INVITE(SDP 2 = inactive) � � INVITE(SDP 2 =

inactive) (CPG 1 (hold))

200 OK (INVITE) � � 200 OK (INVITE) ACK � � ACK CASE B UPDATE(SDP 2 = inactive) � � UPDATE(SDP 2 =

inactive) (CPG 1 (hold))

200 OK (UPDATE) � � 200 OK (UPDATE) INVITE(SDP 3 = recvonly) � � INVITE(SDP 3 =

recvonly) (CPG 2 (retrieve))

200 OK (INVITE) � 200 OK (INVITE) ACK � ACK


ETSI

ETSI TS 101 572-2 V1.2.1 (2014-07)200


TSS reference PSTN-SS/HOLD/ Selection criteria PICS 6.3.2/9 Test Purpose name First hold from SIP. Session inactive, Retrieve requested from ISUP Test Purpose The session is set on hold at first from SIP as well as second from SIP-I . Ensure that on

receipt of an INVITE or UPDATE with encapsulated CPG message and the Generic notification indicator is set to 'remote retrieval', an INVITE or UPDATE request is sent and the media stream in the SDP I set to 'recvonly'




Establish a confirmed dialogue INVITE(SDP 1 = sendonly) � � INVITE(SDP 1 =

sendonly) (CPG(hold))

200 OK (INVITE) � � 200 OK (INVITE) ACK � � ACK CASE A INVITE(SDP 2 = inactive) � � INVITE(SDP 2 =

inactive)CPG(hold) 200 OK (INVITE) � � 200 OK (INVITE) ACK � � ACK CASE B UPDATE(SDP 2 = inactive) � � UPDATE(SDP 2 =


200 OK (UPDATE) � � (UPDATE) CASE C INVITE(SDP 3 = recvonly) � � INVITE(SDP 3 =

recvonly) (CPG(retrieve))

200 OK (INVITE) � � 200 OK (INVITE) ACK � � ACK CASE D UPDATE(SDP 3 = recvonly) � � UPDATE(SDP 3 =



ETSI

ETSI TS 101 572-2 V1.2.1 (2014-07)201


TSS reference PSTN-SS/HOLD/ Selection criteria PICS 6.3.2/9 Test Purpose name First hold from ISUP. Session inactive, Retrieve requested from SIP Test Purpose The session is set on hold at first from SIP-I as well as second from SIP. Ensure that on

receipt of an INVITE request and the media stream in the SDP is set to 'recvonly', a INVITE or UPDATE with encapsulated CPG message is sent and the Generic notification indicator is set to 'remote retrieval'






200 OK (INVITE) � � 200 OK (INVITE) ACK � � ACK CASE B UPDATE(SDP 1 = sendonly) � � UPDATE(SDP 1 =


200 OK (UPDATE) � � 200 OK (UPDATE) INVITE(SDP 2 = inactive) � � INVITE(SDP 2 =


200 OK (INVITE) � � 200 OK (INVITE) ACK � � ACK INVITE(SDP 3 = recvonly) � � INVITE(SDP 3 =


200 OK (INVITE) � � 200 OK (INVITE) ACK � � ACK


ETSI

ETSI TS 101 572-2 V1.2.1 (2014-07)202


TSS reference PSTN-SS/HOLD/ Selection criteria PICS 6.3.2/9 Test Purpose name First hold from ISUP. Session inactive, Retrieve requested from ISUP Test Purpose The session is set on hold at first from ISUP as well as second from SIP. Ensure that on

receipt of a CPG message and the Generic notification indicator is set to 'remote retrieval', an INVITE or UPDATE request is sent and the media stream in the SDP is set to 'recvonly'






200 OK (INVITE) � � 200 OK (INVITE) ACK � � ACK CASE B UPDATE(SDP 1 = sendonly) � � UPDATE(SDP 1 =


200 OK (UPDATE) � � 200 OK (UPDATE) INVITE(SDP 2 = inactive) � � INVITE(SDP 2 =


200 OK (INVITE) � � 200 OK (INVITE) ACK � � ACK CASE C INVITE(SDP 3 = recvonly) � � INVITE(SDP 3 =


200 OK (INVITE) � � 200 OK (INVITE) ACK � � ACK CASE D UPDATE(SDP 3 = recvonly) � � UPDATE

(SDP 3 = recvonly) (CPG(retrieve))


ETSI

ETSI TS 101 572-2 V1.2.1 (2014-07)203


TSS reference PSTN-SS/HOLD/ Selection criteria PICS 6.3.2/9 AND PICS 6.3.6/1 Test Purpose name CPG hold received before an dialogue was established UPDATE is sent in early dialogue Test Purpose Ensure that on receipt of a CPG message and the Generic notification indicator is set to

'remote hold' before an early dialogue is established, the UPDATE request indicating the hold indication is sent after the early dialogue by receiving a 180 Ringing is established. The media stream in the SDP is set to sendonly indicating the hold state


SIP Parameter values UPDATE: SDP a=sendonly

Comments A CPG is received after an ACM was sent. Message flows SIP-I MGCF SIP NNI

INVITE (IAM) � � INVITE � 100 Trying UPDATE (SDP 1 = sendonly) (CPG(hold))

�

200 OK (UPDATE) � 180 Ringing (CPG– alerting )

� � 180 Ringing

� UPDATE(sendonly) � 200 OK (UPDATE)


ETSI

ETSI TS 101 572-2 V1.2.1 (2014-07)204


TSS reference PSTN-SS/HOLD/ Selection criteria PICS 6.3.2/9 AND PICS 6.3.6/1 Test Purpose name CPG hold received before an dialogue was established UPDATE is sent in confirmed

dialogue Test Purpose Ensure that on receipt of a UPDATE with encapsulated CPG message and the Generic

notification indicator is set to 'remote hold' before an early dialogue is established, the INVITE or UPDATE request indicating the hold indication is sent after the confirmed dialogue by receiving a 200 OK (INVITE) is established. The media stream in the SDP is set to sendonly indicating the hold state


SIP Parameter values INVITE/UPDATE: SDP a=sendonly

Comments Message flows ISIP-I MGCF SIP NNI

INVITE (IAM) � � INVITE 100 Trying � � 100 Trying UPDATE (CPG(hold)) � 200 OK (UPDATE)

�

200 OK (INVITE) (CON)


ACK � CASE A � INVITE(sendonly) � 200 OK (INVITE) � ACK CASE B � UPDATE(sendonly) � 200 OK (UPDATE)



TSS reference PSTN-SS/HOLD/ Selection criteria PICS 6.3.2/9 AND PICS 6.3.6/1 Test Purpose name Update with encapsulated CPG hold received after several early dialogues was established

UPDATE is sent on the last established early dialogue Test Purpose Two early dialogues are established. Ensure that on receipt of a INFO with encapsulated

CPG message and the Generic notification indicator is set to 'remote hold', an UPDATE request is sent on the latest established early dialogue


SIP Parameter values 180 1: To: <appropriate URI>; tag=1 180 1: To: <appropriate URI>; tag=2 UPDATE: To: <appropriate URI>; tag=2

Comments For all dialogues the Call-ID and the From tag are equal. The different dialogues can be distinguished by the To tag

Message flows SIP-I MGCF SIP NNI INVITE (IAM) � � INVITE 180 Ringing 1 (ACM – free)

� � 180 Ringing 1

� 180 Ringing 2 UPDATE (sendonly) CPG(hold)

� � UPDATE 2 (sendonly)


ETSI

ETSI TS 101 572-2 V1.2.1 (2014-07)205


TSS reference PSTN-SS/HOLD/ Selection criteria PICS 6.3.2/9 AND PICS 6.3.6/1 Test Purpose name An UPDATE (hold) is repeated in the early dialogue after SDP offer answer exchange Test Purpose Ensure that on receipt of an UPDATE request after the session was set on hold indicating

a new SDP, an UPDATE request is sent and the media stream is set to 'sendonly' to refresh the previous held state


SIP Parameter values INVITE: SDP1 UPDATE 1: SDP a=sendonly UPDATE 2: SDP 2


INVITE(SDP1) (IAM) � � INVITE(SDP1) 180 Ringing (ACM – free)

� � 180 Ringing

UPDATE 1 (sendonly) CPG(hold)


200 OK (UPDATE) � � 200 OK (UPDATE) UPDATE 2 (SDP2) CPG(hold)

� � UPDATE 2 (SDP2)

200 OK (UPDATE) � � 200 OK (UPDATE) UPDATE 1 (sendonly) CPG(retrieve)




TSS reference PSTN-SS/HOLD/ Selection criteria PICS 6.3.2/9 AND PICS 6.3.6/1 Test Purpose name An UPDATE (hold) is sent after an additional early dialogue is established Test Purpose An early dialogue is established and set on hold. Ensure that on receipt of a 180 Ringing

establish a new early dialogue, an UPDATE request is sent on this dialogue and the media stream is set to 'sendonly'


SIP Parameter values 180 1: To: <appropriate URI>; tag=1 180 1: To: <appropriate URI>; tag=2 UPDATE 2: To: <appropriate URI>; tag=2


INVITE (IAM) � � INVITE 180 Ringing 1 (ACM – free)

� � 180 Ringing 1

UPDATE CPG(hold) � � UPDATE 1 (sendonly) 200 OK (UPDATE) � � 200 OK (UPDATE) � 180 Ringing 2 � UPDATE 2 (sendonly) � 200 OK (UPDATE)


ETSI

ETSI TS 101 572-2 V1.2.1 (2014-07)206


TSS reference PSTN-SS/HOLD/ Selection criteria PICS 6.3.2/9 AND PICS 6.3.6/1 Test Purpose name An INVITE or UPDATE (hold condition) is sent after 200 OK INVITE was received when a

CPG (hold) was received in early dialogue Test Purpose An UPDATE with encapsulated CPG indicating Hold was received in the early dialogue.

Ensure that on receipt of a 200 OK (INVITE) establishing the confirmed dialogue, an INVITE or UPDATE request is sent and the media stream is set to 'sendonly' indicating the held state


SIP Parameter values INVITE/UPDATE 2: SDP a=sendonly



� � 180 Ringing

UPDATE (CPG(hold)) � � UPDATE(sendonly) 200 OK (UPDATE) � � 200 OK (UPDATE) 200 OK (INVITE) (ANM)


ACK � � ACK CASE A � INVITE 2 (sendonly) � 200 OK (INVITE) � ACK CASE B � UPDATE 2 (sendonly) � 200 OK (UPDATE)



TSS reference PSTN-SS/HOLD/ Selection criteria PICS 6.3.2/9 AND PICS 6.3.6/1 Test Purpose name 'sendonly' and 'sendrecv' received from the terminating SIP user in the early dialogue Test Purpose Ensure that on receipt of an UPDATE request in the early dialogue and the media stream

is set to 'sendonly' a UPDATE(sendonly) with encapsulated CPG message is sent and the Generic notification indicator is set to 'remote hold'. Ensure that on receipt of an UPDATE request in the early dialogue and the media stream is already set on hold the media stream is set to 'sendrecv' in the received UPDATE, a CPG message is sent and the Generic notification indicator is set to 'remote retrieval'


INVITE IAM � � INVITE � 100 Trying 180 Ringing (ACM – free)

� � 180 Ringing

UPDATE(sendonly) (CPG(hold))

� � UPDATE(sendonly)

200 OK (UPDATE) � � 200 OK (UPDATE) UPDATE(sendrecv) CPG(retrieve)

� � UPDATE(sendrecv)


ETSI

ETSI TS 101 572-2 V1.2.1 (2014-07)207


TSS reference PSTN-SS/HOLD/ Selection criteria PICS 6.3.2/9 AND PICS 6.3.6/1 Test Purpose name 'sendonly' and 'sendrecv' received from the originating SIP user in the early dialogue Test Purpose Ensure that on receipt of an UPDATE request in the early dialogue and the media stream

is set to 'sendonly', a UPDATE with encapsulated CPG message is sent and the Generic notification indicator is set to 'remote hold'. Ensure that on receipt of an UPDATE request in the early dialogue and the media stream is set to 'sendonly' the session is already set on hold, a CPG message is sent and the Generic notification indicator is set to 'remote retrieval'


INVITE � � INVITE (IAM) 180 Ringing � � 180 Ringing (ACM) UPDATE(sendonly) � � UPDATE (sendonly)

(CPG(hold)) 200 OK (UPDATE) � � 200 OK (UPDATE) UPDATE(sendrecv) � � UPDATE(sendrecv)

(CPG(retrieve)) 200 OK (UPDATE) � � 200 OK (UPDATE)



TSS reference PSTN-SS/HOLD/ Selection criteria PICS 6.3.2/9 AND PICS 6.3.6/1 Test Purpose name 'hold' and 'retrieve' received from the originating PSTN user in the early dialogue Test Purpose Ensure that on receipt of a CPG message and the Generic notification indicator is set to

'remote hold' in the early dialogue, an UPDATE request is sent and the mediastream is set to 'sendonly'. Ensure that on receipt of a CPG message and the Generic notification indicator is set to 'remote retrieval' and the session is already set on hold, an UPDATE request is sent and the media stream is set to 'sendrecv'


INVITE (IAM) � � INVITE 100 Trying � � 100 Trying 180 Ringing (ACM – free)

� � 180 Ringing

UPDATE(sendonly) CPG(hold)

� � UPDATE(sendonly)

200 OK (UPDATE) � � 200 OK (UPDATE) UPDATE(sendrecv) (CPG(retrieve))

� � UPDATE(sendrecv)


ETSI

ETSI TS 101 572-2 V1.2.1 (2014-07)208

6.2.9 Call Completion on busy subscriber


TSS reference PSTN-SS/CCBS/ Selection criteria PICS 6.3.1/1 AND PICS 6.3.2/10 Test Purpose name The diagnostic field is not interworked Test Purpose Ensure that on receipt of an REL message cause #17 and a diagnostic field is present set

to 'CCBS possible', a final SIP response 486 Busy Here is sent no indication of CCBS facility is present

ISUP Parameter values REL: Cause indicator CCBS possible indicator=CCBS possible SIP Parameter values Comments The CCBS possible indicator is contained in the diagnostic field of the Cause indicator Message flows SIP NNI MGCF SIP-I

INVITE � � INVITE (IAM) 100 Trying � 486 Busy Here � � 486 Busy Here

(REL(17)) ACK � � ACK (RLC)

6.2.10 Completion of Calls on No Reply (CCNR)


TSS reference PSTN-SS/CCNR/ Selection criteria PICS 6.3.1/1 AND PICS 6.3.2/11 Test Purpose name CCNR possible indication received in an ACM, discarded Test Purpose Ensure that on receipt of an ACM and a CCNR possible indicator is present the value set

to 'CCNR possible', a 180 Ringing is sent without indication of CCNR facility ISUP Parameter values ACM: BCI called party status indicator=subscriber free, CCNR Possible Indicator=CCNR

possible SIP Parameter values Comments Message flows SIP NNI MGCF SIP-I

INVITE � � INVITE (IAM) 100 Trying � 180 Ringing � � 180 Ringing (ACM - free)



TSS reference PSTN-SS/CCNR/ Selection criteria PICS 6.3.1/1 AND PICS 6.3.2/11 Test Purpose name CCNR possible indication received in an CPG, discarded Test Purpose Ensure that on receipt of an CPG and a CCNR possible indicator is present the value set to

'CCNR possible', a 180 Ringing is sent without indication of CCNR facility ISUP Parameter values ACM: BCI called party status indicator=no indication, oBCI=inband info available

CPG: Event indicator= ALERTING, CCNR Possible Indicator=CCNR possible SIP Parameter values Comments Message flows SIP NNI MGCF SIP-I

INVITE � � INVITE (IAM) 100 Trying � � 100 Trying � 183 Session Progress

(ACM(no indication)) 180 Ringing � � 180 Ringing (CPG)


ETSI

ETSI TS 101 572-2 V1.2.1 (2014-07)209

6.2.11 Terminal Portability (TP)


TSS reference PSTN-SS/TP/ Selection criteria PICS 6.3.2/12 Test Purpose name SUS user initiated is mapped into an reINVITE SDP sendonly Test Purpose Ensure that on receipt of an SUS message and the Suspend/Resume indicator is set to

'ISDN subscriber initiated', a reINVITE is sent and the media stream indicated in the SDP is set to 'sendonly'

ISUP Parameter values SUS: Suspend/Resume ISDN subscriber initiated

SIP Parameter values INVITE 2: SDP a=sendonly


INVITE 1 � � INVITE (IAM) 100 Trying � 180 Ringing � � 180 Ringing

(ACM free) 200 OK (INVITE) � � 200 OK (INVITE) (ANM) ACK � � ACK INVITE 2(sendonly) � � INFO (SUS(user)) 200 OK (INVITE) � � 200 OK (INFO) ACK �



TSS reference PSTN-SS/TP/ Selection criteria PICS 6.3.2/12 Test Purpose name RES user initiated is mapped into an reINVITE SDP sendrecv Test Purpose A SUS message and the Suspend/Resume indicator is set to 'ISDN subscriber initiated'

was received. Ensure that on receipt of an RES message and the Suspend/Resume indicator is set to 'ISDN subscriber initiated', a reINVITE is sent and the media stream indicated in the SDP is set to 'sendrecv'

ISUP Parameter values RES: Suspend/Resume ISDN subscriber initiated

SIP Parameter values INVITE 2: SDP a=sendonly INVITE 3: SDP a=sendrecv


INVITE 1 (IAM) � � INVITE � 100 Trying 180 Ringing (ACM – free)

� � 180 Ringing



ACK � � ACK INVITE 2(sendonly) � � INFO (SUS(user)) 200 OK (INVITE) � 200 OK (INFO) ACK � INVITE 3(sendrecv) � � INFO (RES(user)) 200 OK (INVITE) � � 200 OK (INFO) ACK �


ETSI

ETSI TS 101 572-2 V1.2.1 (2014-07)210

6.2.12 Conference calling (CONF) / Three-Party Service (3PTY)


TSS reference PSTN-SS/CONF/ Selection criteria PICS 6.3.1/1 AND PICS 6.3.2/13 Test Purpose name I-MGCF: Session not on hold, notification 'conference established' Test Purpose A session at the I-MGCF is in the confirmed state and not set on hold. Ensure that on

receipt of a reINVITE with encapsulated CPG message the Generic notification indicator is set to 'Conference established' no reINVITE is sent

ISUP Parameter values CPG: Generic notification Conference established

SIP Parameter values Comments This state is applicable for CONF and 3PTY Message flows SIP NNI MGCF SIP-I

INVITE � � INVITE (IAM) 100 Trying � 180 Ringing � � 180 Ringing

(ACM)- free 200 OK (INVITE) � � 200 OK (INVITE) (ANM) ACK � � ACK � INFO (CPG) � 200 OK (INFO)



TSS reference PSTN-SS/CONF/ Selection criteria PICS 6.3.1/1 AND PICS 6.3.2/13 Test Purpose name O-MGCF: Session not on hold, notification 'conference established' Test Purpose A session at the O-MGCF is in the confirmed state and not set on hold. Ensure that on

receipt of a reINVITE with encapsulated CPG message the Generic notification indicator is set to 'Conference established' no reINVITE is sent

ISUP Parameter values CPG: Generic notification= Conference established

SIP Parameter values Comments This state is applicable for CONF and 3PTY Message flows SIP-I MGCF SIP NNI

INVITE (IAM) � � INVITE � 100 Trying 180 Ringing (ACM) � � 180 Ringing 200 OK (INVITE) ANM � � 200 OK (INVITE) ACK � � ACK INFO (CPG) � 200 OK (INFO) �


ETSI

ETSI TS 101 572-2 V1.2.1 (2014-07)211


TSS reference PSTN-SS/CONF/ Selection criteria PICS 6.3.1/1 AND PICS 6.3.2/13 Test Purpose name I-MGCF: Session on hold, notification 'conference established' Test Purpose A session at the I-MGCF is in the confirmed state and set on hold. Ensure that on receipt of

an INVITE with encapsulated CPG message the Generic notification indicator is set to 'Conference established' a reINVITE request is sent the 'a' attribute in the SDP is set to 'sendrecv' On receipt of an INFO with encapsulated CPG message the Generic notification indicator is set to 'Conference established' no reINVITE request is sent the 'a' attribute in the SDP is set to 'sendrecv' will be sent (CASE B)

ISUP Parameter values CPG 1: Generic notification Remote hold CPG 2: Generic notification Conference established


Comments This state is applicable for 3PTY Message flows SIP NNI MGCF SIP-I

INVITE � � INVITE (IAM) 100 Trying � 180 Ringing � � 180 Ringing (ACM - free) 200 OK (INVITE) � � 200 OK (INVITE) (ANM) ACK � � ACK INVITE 1 (sendonly) � � INVITE 1 (sendonly) (CPG 1) 200 OK INVITE (recvonly) � � 200 OK INVITE (recvonly) ACK � � ACK CASE A INVITE 2 (sendrecv) � � INVITE 2 (sendrecv) 200 OK INVITE (sendrecv) � � 200 OK INVITE (sendrecv) ACK � � ACK � INFO(CPG 2) � 200 OK INFO CASE B INVITE 2 (sendrecv) � � INFO(CPG 2) 200 OK INVITE (sendrecv) � � 200 OK INFO ACK �


ETSI

ETSI TS 101 572-2 V1.2.1 (2014-07)212


TSS reference PSTN-SS/CONF/ Selection criteria PICS 6.3.1/1 AND PICS 6.3.2/13 Test Purpose name O-MGCF: Session on hold, notification 'conference established' Test Purpose A session at the O-MGCF is in the confirmed state and set on hold. Ensure that on receipt

of a INVITE with encapsulated CPG message the Generic notification indicator is set to 'Conference established' a reINVITE request is sent the 'a' attribute in the SDP is set to 'sendrecv' On receipt of an INFO with encapsulated CPG message the Generic notification indicator is set to 'Conference established' no reINVITE request is sent the 'a' attribute in the SDP is set to 'sendrecv' will be sent (CASE B)

ISUP Parameter values CPG 1: Generic notification Remote hold CPG 2: Generic notification Conference established


Comments This state is applicable for 3PTY Message flows SIP-I MGCF SIP NNI

INVITE (IAM) � � INVITE � 100 Trying 180 Ringing (ACM – free) � � 180 Ringing 200 OK (INVITE) (ANM) � � 200 OK (INVITE) ACK � � ACK INVITE 1 (sendonly) (CPG 1) � � INVITE 1 (sendonly) 200 OK INVITE (recvonly) � � 200 OK INVITE (recvonly) ACK � � ACK CASE A INVITE 2 (sendrecv) � � INVITE 2 (sendrecv) 200 OK INVITE (sendrecv) � � 200 OK INVITE (sendrecv) ACK � � ACK INFO (CPG 2) � 200 OK INFO � CASE B INFO (CPG 2) � � INVITE 2 (sendrecv) 200 OK INFO � � 200 OK INVITE (sendrecv) � ACK


ETSI

ETSI TS 101 572-2 V1.2.1 (2014-07)213


TSS reference PSTN-SS/CONF/ Selection criteria PICS 6.3.1/1 AND PICS 6.3.2/13 Test Purpose name I-MGCF: Session not on hold, notification 'Conference disconnected' Test Purpose A session at the I-MGCF is in the confirmed state not set on hold and a conference is

established. Ensure that on receipt of an INFO with encapsulated CPG message the Generic notification indicator is set to 'Conference disconnected' no reINVITE is sent

ISUP Parameter values CPG 1: Generic notification Conference established CPG 2: Generic notification Conference disconnected

SIP Parameter values Comments This state is applicable for CONF and 3PTY Message flows SIP NNI MGCF SIP-I

INVITE � � INVITE (IAM) 100 Trying � 180 Ringing � � 180 Ringing (ACM - free) 200 OK (INVITE) � � 200 OK (INVITE) (ANM) ACK � � ACK � INFO 1 (CPG 1) � 200 OK (INFO) � INFO 2 (CPG 2) � 200 OK (INFO)



TSS reference PSTN-SS/CONF/ Selection criteria PICS 6.3.1/1 AND PICS 6.3.2/13 Test Purpose name O-MGCF: Session not on hold, notification 'Conference disconnected' Test Purpose A session at the O-MGCF is in the confirmed state not set on hold and a conference is

established. Ensure that on receipt of an INFO with encapsulated CPG message the Generic notification indicator is set to 'Conference disconnected' no reINVITE is sent

ISUP Parameter values CPG 1: Generic notification Conference established CPG 2: Generic notification Conference disconnected

SIP Parameter values Comments This state is applicable for CONF and 3PTY Message flows SIP-I MGCF SIP NNI

INVITE (IAM) � � INVITE � 100 Trying 180 Ringing (ACM- free)

� � 180 Ringing



ACK � � ACK INFO (CPG 1) � 200 OK (INFO) � INFO (CPG 2) � 200 OK �


ETSI

ETSI TS 101 572-2 V1.2.1 (2014-07)214


TSS reference PSTN-SS/CONF/ Selection criteria PICS 6.3.1/1 AND PICS 6.3.2/13 Test Purpose name I-MGCF: Session on hold, notification 'Conference disconnected' Test Purpose A session at the I-MGCF is in the confirmed state set on hold and a conference is

established. Ensure that on receipt of an INFO with encapsulated CPG message the Generic notification indicator is set to 'Conference disconnected' no action takes place on the SIP side.

ISUP Parameter values CPG 1: Generic notification Remote hold CPG 2: Generic notification Conference established CPG 3: Generic notification Conference disconnected


Comments This state is applicable for 3PTY Message flows SIP NNI MGCF SIP-I

INVITE � � INVITE (IAM) 100 Trying � 180 Ringing � � 180 Ringing (ACM – free) 200 OK (INVITE) � � 200 OK (INVITE) (ANM) ACK � � ACK INVITE 1 (sendonly) � � INVITE 1 (sendonly) (CPG 1) 200 OK INVITE (recvonly) � � 200 OK INVITE (recvonly) ACK � � ACK CASE A INVITE 2 (sendrecv) � � INVITE 2 (sendrecv) 200 OK INVITE (sendrecv) � � 200 OK INVITE (sendrecv) ACK � � ACK � INFO (CPG 3) � 200 OK INFO CASE B INVITE 2 (sendrecv) � � INFO (CPG 2) 200 OK INVITE (sendrecv) � � 200 OK INFO ACK � � INFO (CPG 3) � 200 OK INFO


ETSI

ETSI TS 101 572-2 V1.2.1 (2014-07)215


TSS reference PSTN-SS/CONF/ Selection criteria PICS 6.3.1/1 AND PICS 6.3.2/13 Test Purpose name O-MGCF: Session on hold, notification 'Conference disconnected' Test Purpose A session at the O-MGCF is in the confirmed state set on hold and a conference is

established. Ensure that on receipt of an INFO with encapsulated CPG message the Generic notification indicator is set to 'Conference disconnected' no action takes place on the SIP side.

ISUP Parameter values CPG 1: Generic notification Remote hold CPG 2: Generic notification Conference established CPG 3: Generic notification Conference disconnected


Comments This state is applicable for 3PTY Message flows SIP-I MGCF SIP NNI

A conference is established INVITE (IAM) � � INVITE � 100 Trying 180 Ringing (ACM - free) � � 180 Ringing 200 OK (INVITE) (ANM) � � 200 OK (INVITE) ACK � � ACK INVITE 1 (sendonly) (CPG 1) � � INVITE 1 (sendonly) 200 OK INVITE (recvonly) � � 200 OK INVITE (recvonly) ACK � � ACK CASE A INVITE 2 (sendrecv) � � INVITE 2 (sendrecv) 200 OK INVITE (sendrecv) � 200 OK INVITE (sendrecv) ACK � � ACK INFO (CPG 2) � 200 OK INFO � INFO (CPG 3) � 200 OK INFO � CASE B INFO (CPG 2) � � INVITE 2 (sendrecv) 200 OK INFO � � 200 OK INVITE (sendrecv) � ACK INFO (CPG 3) � 200 OK INFO �


ETSI

ETSI TS 101 572-2 V1.2.1 (2014-07)216


TSS reference PSTN-SS/CONF/ Selection criteria PICS 6.3.1/1 AND PICS 6.3.2/13 Test Purpose name I-MGCF: notification 'isolated' and 'reattached' interworked Test Purpose A conference at the I-MFCF is established. Ensure that on receipt of an INVITE with

encapsulated CPG message the Generic notification indicator is set to 'isolated' a reINVITE request is sent the 'a' attribute in the SDP is set to 'sendonly'. Subsequently on receipt of a CPG message the Generic notification indicator is set to 'reattached' a reINVITE request is sent the 'a' attribute in the SDP is set to 'sendrecv'

ISUP Parameter values CPG 1: Generic notification Conference established CPG 2: Generic notification isolated CPG 3: Generic notification reattached


Comments This state is applicable for CONF Message flows SIP NNI MGCF SIP-I

INVITE � � INVITE (IAM) 100 Trying � 180 Ringing � � 180 Ringing (ACM) 200 OK (INVITE) � � 200 OK (INVITE) (ANM) ACK � � ACK � INFO (CPG 1) � 200 OK (INFO) INVITE 1 (sendonly) � � INFO CPG 2 200 OK INVITE (recvonly) � � 200 OK INFO ACK � INVITE 2 (sendrecv) � � INFO (CPG 3) 200 OK INVITE (sendrecv) � � 200 OK INFO ACK �


ETSI

ETSI TS 101 572-2 V1.2.1 (2014-07)217


TSS reference PSTN-SS/CONF/ Selection criteria PICS 6.3.1/1 AND PICS 6.3.2/13 Test Purpose name O-MGCF: notification 'isolated' and 'reattached' interworked Test Purpose A conference at the O-MFCF is established. Ensure that on receipt of a reINVITE with

encapsulated CPG message the Generic notification indicator is set to 'isolated' a reINVITE request is sent the 'a' attribute in the SDP is set to 'sendonly'. Subsequently on receipt of a CPG message the Generic notification indicator is set to 'reattached' a reINVITE request is sent the 'a' attribute in the SDP is set to 'sendrecv'

ISUP Parameter values CPG 1: Generic notification Conference established CPG 2: Generic notification isolated CPG 2: Generic notification reattached


Comments This state is applicable for CONF Message flows SIP-I MGCF SIP NNI

INVITE (IAM) � � INVITE � 100 Trying 180 Ringing (ACM – free) � � 180 Ringing 200 OK (INVITE) (ANM) � � 200 OK (INVITE) ACK � � ACK INFO (CPG 1) � 200 OK (INFO) � INFO (CPG 2) � � INVITE 1 (sendonly) 200 OK INFO � � 200 OK INVITE (recvonly) ACK � � ACK INFO (CPG 3) � � INVITE 2 (sendrecv) 200 OK INFO) � � 200 OK INVITE (sendrecv) ACK � � ACK


6.2.13 Void

6.2.14 Multi-Level Precedence and Pre-emption (MLPP)


TSS reference PSTN-SS/MLPP/ Selection criteria Test Purpose name Precedence parameter received in IAM, discarded Test Purpose Ensure that on receipt of an INVITE with encapsulated IAM and a Precedence parameter is

present, this parameter is discarded without affect the ongoing call setup ISUP Parameter values IAM: Precedence SIP Parameter values Comments Message flows SIP-I MGCF SIP NNI



ETSI

ETSI TS 101 572-2 V1.2.1 (2014-07)218


TSS reference PSTN-SS/MLPP/ Selection criteria Test Purpose name A REL cause #9 terminates an early dialogue Test Purpose Ensure that on receipt of a CANCEL with encapsulated REL message in an early dialogue

at the O-MGCF and the Cause value is set to '9', a CANCEL request is sent. A Reason header is contained in the CANCEL request and the cause value is set to '9'

ISUP Parameter values REL: Cause = 9 SIP Parameter values CANCEL: Reason: Q.850; cause=9 Comments Message flows SIP-I MGCF SIP NNI

A Session is already in early dialogue CANCEL (REL) � � CANCEL 200 OK CANCEL (RLC)

� � 200 OK CANCEL

487 Request Terminated

� � 487 Request Terminated

ACK � � ACK


TSS reference PSTN-SS/MLPP/ Selection criteria Test Purpose name A REL cause #8 terminates an early dialogue Test Purpose Ensure that on receipt of a 4xx/5xx with encapsulated REL message in an early dialogue at

the I-MGCF and the Cause value is set to '8', a 4xx or 5xx final response is sent. A Reason header is contained in the final response message and the cause value is set to '9'

ISUP Parameter values REL: Cause = 8 SIP Parameter values 480: Reason: Q.850; cause=8 Comments Message flows SIP NNI MGCF SIP-I

A Session is already in early dialogue 4xx/5xx � � 4xx/5xx (REL) ACK � � ACK (RLC)


TSS reference PSTN-SS/MLPP/ Selection criteria PICS 6.3.1/1 AND PICS 6.3.2/15 Test Purpose name A REL cause #9 terminates a confirmed dialogue Test Purpose Ensure that on receipt of a REL message in a confirmed dialogue and the Cause value is

set to '9', a BYE request is sent. A Reason header is contained in the BYE request and the cause value is set to '9'

ISUP Parameter values REL: Cause = 9 SIP Parameter values BYE: Reason: Q.850; cause=9 Comments Message flows SIP-I MGCF SIP NNI

A Session is already established BYE (REL) � � BYE 200 OK BYE (RLC) � � 200 OK BYE

ETSI

ETSI TS 101 572-2 V1.2.1 (2014-07)219

6.2.15 Global Virtual Network Service (GVNS)


TSS reference PSTN-SS/GVNS/ Selection criteria Test Purpose name Forward GVNS parameter in IAM discarded Test Purpose Ensure that on receipt of an INVITE with encapsulated IAM containing a request for GVNS

service, the Forward GVNS parameter is discarded without affect the ongoing call setup ISUP Parameter values IAM: Called party number

Forward GVNS Originating participating service provider GVNS user group Terminating network routing number




6.2.16 Reverse charging (REV)


TSS reference PSTN-SS/REV/ Selection criteria PICS 6.3.7/1 AND PICS 6.3.1/1 AND PICS 6.3.2/17 Test Purpose name REV request from the calling user at the call set-up time Test Purpose Ensure that on receipt of an INVITE with encapsulated IAM and a Remote Operation

parameter is present containing a REVCallingReqSetup invoke component, the Remote Operation parameter is discarded without affect the ongoing call setup

ISUP Parameter values IAM: Called party number Remote Operation REVCallingReqSetup invoke transferRequested = true callingUserNumber





TSS reference PSTN-SS/REV/ Selection criteria Test Purpose name REV request from the calling user during the active state of the call Test Purpose Ensure that on receipt of a INFO with encapsulated FAC message at the O-MGCF in the

active state of a call and a Remote Operation parameter is present containing a REVCallingReqActive invoke component, the FAC message is discarded without affect the present call

ISUP Parameter values FAC: Remote Operation REVCallingReqActive invoke transferRequested = true callingUserNumber


A confirmed dialogue is already established INFO (FAC) � 200 OK INFO �


ETSI

ETSI TS 101 572-2 V1.2.1 (2014-07)220


TSS reference PSTN-SS/REV/ Selection criteria Test Purpose name REV request from the called user during the active state of the call Test Purpose Ensure that on receipt of a INFO with encapsulated FAC message at the I-MGCF in the

active state of a call and a Remote Operation parameter is present containing a REVCalledRequest invoke component, the FAC message is discarded without affect the present call

ISUP Parameter values FAC: Remote Operation REVCalledRequest invoke transferRequested = true calledUserNumber


A confirmed dialogue is already established � INFO (FAC) � 200 OK INFO



TSS reference PSTN-SS/REV/ Selection criteria Test Purpose name REV request in IAM explicit rejected Test Purpose Ensure that on receipt of an INVITE with encapsulated IAM message and a Remote

Operation parameter is present containing REVCallingReqSetup invoke component and the explicit rejection of this service is supported, the SUT sends in a: • 200 OK INVITE with encapsulated ANM a Remote Operation parameter containing a

REVCallingReqSetup return error component set to rejectedByNetwork OR • BYE with encapsulated REL a Remote Operation parameter containing a

REVCallingReqSetup return error component set to rejectedByNetwork and the Cause value is set to '29'

ISUP Parameter values IAM: Called party number Remote Operation REVCallingReqSetup invoke transferRequested = true callingUserNumber ANM: Remote Operation REVCallingReqSetup return error rejectedByNetwork REL: Cause 29 Remote Operation REVCallingReqSetup return error rejectedByNetwork


INVITE (IAM) � CASE A � INVITE 180 Ringing (ACM – free)

� � 180 Ringing

200 OK INVITE (ANM) � � 200 OK INVITE ACK � � ACK

Apply post test routine CASE B 4xx/5xx/6xx (REL) � ACK (RLC) �

ETSI

ETSI TS 101 572-2 V1.2.1 (2014-07)221


TSS reference PSTN-SS/REV/ Selection criteria Test Purpose name REV request in the active state explicit rejected at the O-MGCF Test Purpose Ensure that on receipt of an INFO with encapsulated FAC message at the O-MGCF in the

active state of the call and a Remote Operation parameter is present containing REVCallingReqSetup invoke component and the explicit rejection of this service is supported, the SUT sends in a INFO with encapsulated FRJ message a Remote Operation parameter containing a REVCallingReqActive return error component set to rejectedByNetwork

ISUP Parameter values FAC: Remote Operation REVCallingReqActive invoke transferRequested = true callingUserNumber FRJ: Remote Operation REVCallingReqActive return error rejectedByNetwork


A confirmed dialogue is already established INFO (FAC) � 200 OK INFO � INFO (FRJ) � 200 OK INFO �



TSS reference PSTN-SS/REV/ Selection criteria Test Purpose name REV request in the active state explicit rejected at the I-MGCF Test Purpose Ensure that on receipt of an INFO with encapsulated FAC message at the O-MGCF in the

active state of the call and a Remote Operation parameter is present containing REVCallingReqSetup invoke component and the explicit rejection of this service is supported, the SUT sends in a INFO with encapsulated FRJ message a Remote Operation parameter containing a REVCalledRequest return error component set to rejectedByNetwork

ISUP Parameter values FAC: Remote Operation REVCalledRequest invoke transferRequested = true calledUserNumber FRJ: Remote Operation REVCalledRequest return error rejectedByNetwork


A confirmed dialogue is already established � INFO (FAC) � 200 OK INFO � INFO (FRJ) � 200 OK INFO


ETSI

ETSI TS 101 572-2 V1.2.1 (2014-07)222

6.2.17 Void

6.2.18 Void

6.3 IMS Supplementary Services

6.3.1 Originating Identification Presentation (OIP) and Originating Identification Restriction (OIR)


TSS reference IMS-SS/OIP-OIR/ Selection criteria PICS 6.3.3/1 AND PICS 6.3.2/1 Test Purpose name INVITE received. From header not present, P-Asserted-Identity not present. Network

provided number is sent Test Purpose Ensure that on receipt of an INVITE request the P-Asserted-Identity is not present and the

From header does not contain an URI that encodes an E.164 [i.1] Address, an INVITE with encapsulated IAM is sent. An Calling party number parameter is present and the address digits are provided by the SUT

ISUP Parameter values IAM: Calling party Number Number incomplete indicator=Complete Numbering Plan Indicator=ISDN/Telephony (Recommendation E.164) Nature of Address Indicator If CC encoded in the URI is equal to the CC of the country where MGCF is located AND the next BICC/ISUP node is located in the same country then national (significant) number else international number Screening indicator=Network Provided Presentation restriction=restricted or allowed Address signal provided by the Network if NOA is "national (significant) number" then set to "NDC" + "SN" If NOA is "international number" then set to "CC"+" NDC"+"SN"

SIP Parameter values INVITE: P-Asserted-Identity: not present From: sip:[email protected]


INVITE � � INVITE (IAM 100 Trying �


ETSI

ETSI TS 101 572-2 V1.2.1 (2014-07)223

TP number TP_401_002 Reference [1], clause 7.2.1 [2], clauses 7.5.1, 7.2.3.1.2.6

TSS reference IMS-SS/OIP-OIR/ Selection criteria PICS 6.3.3/1 AND PICS 6.3.3/4 AND PICS 6.3.2/1 Test Purpose name INVITE received. From header not present, P-Asserted-Identity not present. Network

provided number is sent Test Purpose Ensure that on receipt of an INVITE request the P-Asserted-Identity is not present and the

From header does not contain an URI that encodes an E.164 [i.1] Address, an INVITE with encapsulated IAM is sent. A Calling party number parameter is present and the address digits are provided by the SUT. The Presentation restriction indicator is set to 'presentation restricted by network'

ISUP Parameter values IAM: Calling party Number Number incomplete indicator=Complete Numbering Plan Indicator=ISDN/Telephony (Recommendation E.164 [i.1]) Nature of Address Indicator If CC encoded in the URI is equal to the CC of the country where MGCF is located AND the next BICC/ISUP node is located in the same country then national (significant) number else international number Screening indicator=Network Provided Presentation restriction=presentation restricted by network Address signal provided by the Network if NOA is "national (significant) number" then set to "NDC" + "SN" If NOA is "international number" then set to "CC"+" NDC"+"SN"






TSS reference IMS-SS/OIP-OIR/ Selection criteria NOT PICS 6.3.3/2 AND NOT PICS6.3.3/1 AND PICS 6.3.2/1 Test Purpose name INVITE received. From header not present, P-Asserted-Identity not present. Address digits

omitted Test Purpose Ensure that on receipt of an INVITE request the P-Asserted-Identity is not present and the

From header does not contain an URI that encodes an E.164 [i.1] Address, an INVITE with encapsulated IAM is sent. A Calling party number parameter is not present and a Generic number parameter is not present.

ISUP Parameter values IAM: Calling party Number not present





ETSI

ETSI TS 101 572-2 V1.2.1 (2014-07)224


TSS reference IMS-SS/OIP-OIR/ Selection criteria PICS 6.3.3/1 AND PICS 6.3.3/2 AND PICS 6.3.3/3 AND PICS 6.3.2/1 Test Purpose name INVITE received. From header not present, P-Asserted-Identity not present APRI is set to

'Address not available' Test Purpose Ensure that on receipt of an INVITE request the P-Asserted-Identity is not present and the

From header does not contain an URI that encodes an E.164 [i.1] Address, an INVITE with encapsulated IAM is sent. A Calling party number parameter is present and the address digits omitted. The Presentation restriction indicator is set to 'Address not available'

ISUP Parameter values IAM: Calling party Number Number incomplete indicator=Complete Numbering Plan Indicator='000' Nature of Address Indicator='0000000' Screening indicator=Network Provided Presentation restriction=Address not available Address signal Address digits not present





ETSI

ETSI TS 101 572-2 V1.2.1 (2014-07)225


TSS reference IMS-SS/OIP-OIR/ Selection criteria PICS 6.3.3/1 PICS 6.3.2/1 Test Purpose name INVITE received. From header present, P-Asserted-Identity not present. Network provided

number is sent Test Purpose Ensure that on receipt of an INVITE request the P-Asserted-Identity is not present and the

From header contains an URI that encodes an E.164 [i.1] Address, an INVITE with encapsulated IAM is sent. A Calling party number parameter is present and the address digits are provided by the SUT. An Additional calling Party number is sent in a Generic number parameter and the Address signals are derived from the Userpart of the From header

ISUP Parameter values IAM: Calling party Number Number incomplete indicator=Complete Numbering Plan Indicator=ISDN/Telephony (Recommendation E.164 [i.1]) Nature of Address Indicator If CC encoded in the URI is equal to the CC of the country where MGCF is located AND the next BICC/ISUP node is located in the same country then national (significant) number else international number Screening indicator=Network Provided Presentation restriction=restricted or allowed Address signal provided by the Network if NOA is "national (significant) number" then set to "NDC" + "SN" If NOA is "international number" then set to "CC"+" NDC"+"SN" Additional calling party number Nature of Address Indicator If CC encoded in the URI is equal to the CC of the country where MGCF is located AND the next BICC/ISUP node is located in the same country then national (significant) number else international number Number incomplete indicator=Complete Numbering Plan Indicator=ISDN/Telephony (Recommendation E.164) Presentation restriction=restricted or allowed Screening indicator=user provided not verified Address digits derived from the 'From' header if NOA is "national (significant) number" then set to "NDC" + "SN" If NOA is "international number" set to "CC"+' NDC'+'SN'

SIP Parameter values INVITE: P-Asserted-Identity: not present From: contains a URI that encodes an E.164 [i.1] address


INVITE � � INVITE (IAM) 100 Trying � � 100 Trying


ETSI

ETSI TS 101 572-2 V1.2.1 (2014-07)226


TSS reference IMS-SS/OIP-OIR/ Selection criteria PICS 6.3.3/1 AND PICS 6.3.3/4 AND PICS 6.3.2/1 Test Purpose name INVITE received. From header present, P-Asserted-Identity not present. Network provided

number is sent Test Purpose Ensure that on receipt of an INVITE request the P-Asserted-Identity is not present and the

From header contains an URI that encodes an E.164 [i.1] Address, an INVITE with encapsulated IAM is sent. A Calling party number parameter is present and the address digits are provided by the SUT. The Presentation restriction indicator is set to 'presentation restricted by network'. An Additional calling Party number is sent in a Generic number parameter and the Address signals are derived from the Userpart of the From header and the Presentation restriction indicator is set to 'presentation allowed'

ISUP Parameter values IAM: Calling party Number Number incomplete indicator=Complete Numbering Plan Indicator=ISDN/Telephony (Recommendation E.164) Nature of Address Indicator If CC encoded in the URI is equal to the CC of the country where MGCF is located AND the next BICC/ISUP node is located in the same country then national (significant) number else international number Screening indicator=Network Provided Presentation restriction=presentation restricted by network Address signal provided by the Network if NOA is "national (significant) number" then set to "NDC" + "SN" If NOA is "international number" then set to "CC"+" NDC"+"SN" Additional calling party number Nature of Address Indicator If CC encoded in the URI is equal to the CC of the country where MGCF is located AND the next BICC/ISUP node is located in the same country then national (significant) number else international number Number incomplete indicator=Complete Numbering Plan Indicator=ISDN/Telephony (Recommendation E.164) Presentation restriction=allowed Screening indicator=user provided not verified Address digits derived from the 'From' header if NOA is "national (significant) number" then set to "NDC" + "SN" If NOA is "international number" set to "CC"+' NDC'+'SN'





ETSI

ETSI TS 101 572-2 V1.2.1 (2014-07)227


TSS reference IMS-SS/OIP-OIR/ Selection criteria NOT PICS 6.3.3/1 AND PICS 6.3.3/2 AND PICS 6.3.3/3 AND PICS 6.3.2/1 Test Purpose name INVITE received. From header present, P-Asserted-Identity not present. Address digits


From header does not contain an URI that encodes an E.164 [i.1] Address, an INVITE with encapsulated IAM is sent. A Calling party number parameter is present and the address digits omitted. An Additional calling Party number is sent in a Generic number parameter and the Address signals are derived from the Userpart of the From header

ISUP Parameter values IAM: Calling party Number Number incomplete indicator=Complete Numbering Plan Indicator='000' Nature of Address Indicator='0000000' Screening indicator=Network Provided Presentation restriction= Address not available Address signal Address digits not present Additional calling party number Nature of Address Indicator If CC encoded in the URI is equal to the CC of the country where MGCF is located AND the next BICC/ISUP node is located in the same country then national (significant) number else international number Number incomplete indicator=Complete Numbering Plan Indicator=ISDN/Telephony (Recommendation E.164) Presentation restriction=restricted or allowed Screening indicator=user provided not verified Address digits derived from the 'From' header if NOA is "national (significant) number" then set to "NDC" + "SN" If NOA is "international number" set to "CC"+' NDC'+'SN'






TSS reference IMS-SS/OIP-OIR/ Selection criteria NOT PICS 6.3.3/1 AND NOT PICS 6.3.3/2 AND PICS 6.3.3/5 AND PICS 6.3.2/1 Test Purpose name INVITE received. From header present, P-Asserted-Identity not present. Address digits


From header does not contain an URI that encodes an E.164 [i.1] Address, an INVITE with encapsulated IAM is sent. A Calling party number parameter is present and the address digits omitted. In addition, the Additional calling party number is omitted.

ISUP Parameter values IAM: Calling party Number not present Additional calling party number not present





ETSI

ETSI TS 101 572-2 V1.2.1 (2014-07)228


TSS reference IMS-SS/OIP-OIR/ Selection criteria PICS 6.3.2/1 Test Purpose name INVITE received. From header not present, P-Asserted-Identity present Privacy not present Test Purpose Ensure that on receipt of an INVITE request the P-Asserted-Identity is present and the

From header does not contain an URI that encodes an E.164 [i.1] Address a Privacy header is not present, an INVITE with encapsulated IAM is sent. A Calling party number parameter is present and the address digits are derived from the P-Asserted-Identity header

ISUP Parameter values IAM: Calling party Number Number incomplete indicator=Complete Numbering Plan Indicator=ISDN/Telephony (Recommendation E.164) Nature of Address Indicator If CC encoded in the URI is equal to the CC of the country where MGCF is located AND the next BICC/ISUP node is located in the same country then national (significant) number else international number Screening indicator=Network Provided Presentation restriction=allowed Address signal derived from the P-Asserted-Identity if NOA is "national (significant) number" then set to "NDC" + "SN" If NOA is "international number" then set to "CC"+" NDC"+"SN"

SIP Parameter values INVITE: P-Asserted-Identity: present From: sip:[email protected] Privacy not present




ETSI

ETSI TS 101 572-2 V1.2.1 (2014-07)229


TSS reference IMS-SS/OIP-OIR/ Selection criteria PICS 6.3.2/1 Test Purpose name INVITE received. From header not present, P-Asserted-Identity present, Privacy value

'none' Test Purpose Ensure that on receipt of an INVITE request the P-Asserted-Identity is present and the

From header does not contain an URI that encodes an E.164 [i.1] Address and a Privacy header is present set to 'none', an INVITE with encapsulated IAM is sent. A Calling party number parameter is present and the address digits are derived from the P-Asserted-Identity header. The Presentation restriction is set to 'presentation 'allowed'

ISUP Parameter values IAM: Calling party Number Number incomplete indicator=Complete Numbering Plan Indicator=ISDN/Telephony (Recommendation E.164 [i.1]) Nature of Address Indicator If CC encoded in the URI is equal to the CC of the country where MGCF is located AND the next BICC/ISUP node is located in the same country then national (significant) number else international number Screening indicator=Network Provided Presentation restriction=allowed Address signal derived from the P-Asserted-Identity if NOA is "national (significant) number" then set to "NDC" + "SN" If NOA is "international number" then set to "CC"+" NDC"+"SN"

SIP Parameter values INVITE: P-Asserted-Identity: present From: sip:[email protected] Privacy: none




ETSI

ETSI TS 101 572-2 V1.2.1 (2014-07)230


TSS reference IMS-SS/OIP-OIR/ Selection criteria PICS 6.3.2/1 Test Purpose name INVITE received. From header not present, P-Asserted-Identity present, Privacy value 'id' Test Purpose Ensure that on receipt of an INVITE request the P-Asserted-Identity is present and the

From header does not contain an URI that encodes an E.164 [i.1] Address and a Privacy header is present set to 'id', an INVITE with encapsulated IAM is sent. A Calling party number parameter is present and the address digits are derived from the P-Asserted-Identity header. The Presentation restriction is set to 'presentation 'restricted'

ISUP Parameter values IAM: Calling party Number Number incomplete indicator=Complete Numbering Plan Indicator=ISDN/Telephony (Recommendation E.164 [i.1]) Nature of Address Indicator If CC encoded in the URI is equal to the CC of the country where MGCF is located AND the next BICC/ISUP node is located in the same country then national (significant) number else international number Screening indicator=Network Provided Presentation restriction=restricted Address signal derived from the P-Asserted-Identity if NOA is "national (significant) number" then set to "NDC" + "SN" If NOA is "international number" then set to "CC"+" NDC"+"SN"

SIP Parameter values INVITE: P-Asserted-Identity: present From: sip:[email protected] Privacy: id




ETSI

ETSI TS 101 572-2 V1.2.1 (2014-07)231



'user' Test Purpose Ensure that on receipt of an INVITE request the P-Asserted-Identity is present and the

From header does not contain an URI that encodes an E.164 [i.1] Address and a Privacy header is present set to 'user', an INVITE with encapsulated IAM is sent. A Calling party number parameter is present and the address digits are derived from the P-Asserted-Identity header. The Presentation restriction is set to 'presentation 'restricted'


SIP Parameter values INVITE: P-Asserted-Identity: present From: sip:[email protected] Privacy: user




ETSI

ETSI TS 101 572-2 V1.2.1 (2014-07)232



'header' Test Purpose Ensure that on receipt of an INVITE request the P-Asserted-Identity is present and the

From header does not contain an URI that encodes an E.164 [i.1] Address and a Privacy header is present set to 'header', an INVITE with encapsulated IAM is sent. A Calling party number parameter is present and the address digits are derived from the P-Asserted-Identity header. The Presentation restriction is set to 'presentation 'restricted'


SIP Parameter values INVITE: P-Asserted-Identity: present From: sip:[email protected] Privacy: header




ETSI

ETSI TS 101 572-2 V1.2.1 (2014-07)233


TSS reference IMS-SS/OIP-OIR/ Selection criteria NOT PICS 6.3.3/6 AND PICS 6.3.2/1 Test Purpose name INVITE received. From header present, P-Asserted-Identity present. Privacy header not

present, additional calling party number not omitted Test Purpose Ensure that on receipt of an INVITE request the P-Asserted-Identity is present and the

From header contains an URI that encodes an E.164 [i.1] Address a Privacy header is not present, an INVITE with encapsulated IAM is sent. A Calling party number parameter is present and the address digits are derived from the P-Asserted-Identity header the Presentation restriction indicator is set to 'presentation allowed'. An Additional calling Party number is sent in a Generic number parameter and the Address signals are derived from the Userpart of the From header the Presentation restriction indicator is set to 'presentation allowed'.

ISUP Parameter values IAM: Calling party Number Number incomplete indicator=Complete Numbering Plan Indicator=ISDN/Telephony (Recommendation E.164 [i.1]) Nature of Address Indicator If CC encoded in the URI is equal to the CC of the country where MGCF is located AND the next BICC/ISUP node is located in the same country then national (significant) number else international number Screening indicator=Network Provided Presentation restriction=allowed Address signal derived from the P-Asserted-Identity if NOA is "national (significant) number" then set to "NDC" + "SN" If NOA is "international number" then set to "CC"+" NDC"+"SN" Additional calling party number Nature of Address Indicator If CC encoded in the URI is equal to the CC of the country where MGCF is located AND the next BICC/ISUP node is located in the same country then national (significant) number else international number Number incomplete indicator=Complete Numbering Plan Indicator=ISDN/Telephony (Recommendation E.164) Presentation restriction=allowed Screening indicator=user provided not verified Address digits derived from the 'From' header if NOA is "national (significant) number" then set to "NDC" + "SN" If NOA is "international number" set to "CC"+' NDC'+'SN'

SIP Parameter values INVITE: P-Asserted-Identity: present From: contains a URI that encodes an E.164 [i.1] address Privacy not present




ETSI

ETSI TS 101 572-2 V1.2.1 (2014-07)234


TSS reference IMS-SS/OIP-OIR/ Selection criteria NOT PICS 6.3.3/6 AND PICS 6.3.2/1 Test Purpose name INVITE received. From header present, P-Asserted-Identity present. Privacy header 'none',

additional calling party number not omitted Test Purpose Ensure that on receipt of an INVITE request the P-Asserted-Identity is present and the

From header contains an URI that encodes an E.164 [i.1] Address, an INVITE with encapsulated IAM is sent with Privacy header is present set to 'none', A Calling party number parameter is present and the address digits are derived from the P-Asserted-Identity header the Presentation restriction indicator is set to 'presentation allowed'. An Additional calling Party number is sent in a Generic number parameter and the Address signals are derived from the Userpart of the From header the Presentation restriction indicator is set to 'presentation allowed'.

ISUP Parameter values IAM: Calling party Number Number incomplete indicator=Complete Numbering Plan Indicator=ISDN/Telephony (Recommendation E.164 [i.1]) Nature of Address Indicator If CC encoded in the URI is equal to the CC of the country where MGCF is located AND the next BICC/ISUP node is located in the same country then national (significant) number else international number Screening indicator=Network Provided Presentation restriction=allowed Address signal derived from the P-Asserted-Identity if NOA is "national (significant) number" then set to "NDC" + "SN" If NOA is "international number" then set to "CC"+" NDC"+"SN" Additional calling party number Nature of Address Indicator If CC encoded in the URI is equal to the CC of the country where MGCF is located AND the next BICC/ISUP node is located in the same country then national (significant) number else international number Number incomplete indicator=Complete Numbering Plan Indicator=ISDN/Telephony (Recommendation E.164 [i.1]) Presentation restriction=allowed Screening indicator=user provided not verified Address digits derived from the 'From' header if NOA is "national (significant) number" then set to "NDC" + "SN" If NOA is "international number" set to "CC"+' NDC'+'SN'

SIP Parameter values INVITE: P-Asserted-Identity: present From: contains a URI that encodes an E.164 address Privacy: none




ETSI

ETSI TS 101 572-2 V1.2.1 (2014-07)235


TSS reference IMS-SS/OIP-OIR/ Selection criteria NOT PICS 6.3.3/6 AND PICS 6.3.2/1 Test Purpose name INVITE received. From header present, P-Asserted-Identity present. Privacy header 'id',


From header contains an URI that encodes an E.164 [i.1] Address, an INVITE with encapsulated IAM is sent with Privacy header is present set to 'id', A Calling party number parameter is present and the address digits are derived from the P-Asserted-Identity header the Presentation restriction indicator is set to 'presentation restricted'. An Additional calling Party number is sent in a Generic number parameter and the Address signals are derived from the Userpart of the From header the Presentation restriction indicator is set to 'presentation restricted'.

ISUP Parameter values IAM: Calling party Number Number incomplete indicator=Complete Numbering Plan Indicator=ISDN/Telephony (Recommendation E.164 [i.1]) Nature of Address Indicator If CC encoded in the URI is equal to the CC of the country where MGCF is located AND the next BICC/ISUP node is located in the same country then national (significant) number else international number Screening indicator=Network Provided Presentation restriction=restricted Address signal derived from the P-Asserted-Identity if NOA is "national (significant) number" then set to "NDC" + "SN" If NOA is "international number" then set to "CC"+" NDC"+"SN" Additional calling party number Nature of Address Indicator If CC encoded in the URI is equal to the CC of the country where MGCF is located AND the next BICC/ISUP node is located in the same country then national (significant) number else international number Number incomplete indicator=Complete Numbering Plan Indicator=ISDN/Telephony (Recommendation E.164) Presentation restriction=restricted Screening indicator=user provided not verified Address digits derived from the 'From' header if NOA is "national (significant) number" then set to "NDC" + "SN" If NOA is "international number" set to "CC"+' NDC'+'SN'

SIP Parameter values INVITE: P-Asserted-Identity: present From: contains a URI that encodes an E.164 [i.1] address Privacy: id




ETSI

ETSI TS 101 572-2 V1.2.1 (2014-07)236


TSS reference IMS-SS/OIP-OIR/ Selection criteria NOT PICS 6.3.3/6 AND PICS 6.3.2/1 Test Purpose name INVITE received. From header present, P-Asserted-Identity present. Privacy header 'user',


From header contains an URI that encodes an E.164 [i.1] Address, an INVITE with encapsulated IAM is sent with Privacy header is present set to 'user', A Calling party number parameter is present and the address digits are derived from the P-Asserted-Identity header the Presentation restriction indicator is set to 'presentation restricted'. An Additional calling Party number is sent in a Generic number parameter and the Address signals are derived from the Userpart of the From header the Presentation restriction indicator is set to 'presentation restricted'


SIP Parameter values INVITE: P-Asserted-Identity: present From: contains a URI that encodes an E.164 [i.1] address Privacy: user




ETSI

ETSI TS 101 572-2 V1.2.1 (2014-07)237


TSS reference IMS-SS/OIP-OIR/ Selection criteria NOT PICS 6.3.3/6 AND PICS 6.3.2/1 Test Purpose name INVITE received. From header present, P-Asserted-Identity present. Privacy header

'header', additional calling party number not omitted Test Purpose Ensure that on receipt of an INVITE request the P-Asserted-Identity is present and the

From header contains an URI that encodes an E.164 [i.1] Address, an INVITE with encapsulated IAM is sent Privacy header is present set to 'header', A Calling party number parameter is present and the address digits are derived from the P-Asserted-Identity header the Presentation restriction indicator is set to 'presentation restricted'. An Additional calling Party number is sent in a Generic number parameter and the Address signals are derived from the Userpart of the From header the Presentation restriction indicator is set to 'presentation restricted'


SIP Parameter values INVITE: P-Asserted-Identity: present From: contains a URI that encodes an E.164 [i.1] address Privacy: header




ETSI

ETSI TS 101 572-2 V1.2.1 (2014-07)238


TSS reference IMS-SS/OIP-OIR/ Selection criteria PICS 6.3.3/6 AND PICS 6.3.2/1 Test Purpose name INVITE received. From header present, P-Asserted-Identity present. Privacy header not

present, additional calling party number omitted Test Purpose Ensure that on receipt of an INVITE request the P-Asserted-Identity is present and the

From header contains an URI that encodes an E.164 [i.1] Address a Privacy header is not present, an INVITE with encapsulated IAM is sent. A Calling party number parameter is present and the address digits are derived from the P-Asserted-Identity header the Presentation restriction indicator is set to 'presentation allowed'. An Additional calling Party number parameter is not present


SIP Parameter values INVITE: P-Asserted-Identity: present From: contains a URI that encodes an E.164 [i.1] address Privacy not present


INVITE � � (INVITE) IAM 100 Trying �


ETSI

ETSI TS 101 572-2 V1.2.1 (2014-07)239


TSS reference IMS-SS/OIP-OIR/ Selection criteria PICS 6.3.3/6 AND PICS 6.3.2/1 Test Purpose name INVITE received. From header present, P-Asserted-Identity present. Privacy header 'none',

additional calling party number omitted Test Purpose Ensure that on receipt of an INVITE request the P-Asserted-Identity is present and the

From header contains an URI that encodes an E.164 [i.1] Address a Privacy header is set to 'none', an INVITE with encapsulated IAM is sent. A Calling party number parameter is present and the address digits are derived from the P-Asserted-Identity header the Presentation restriction indicator is set to 'presentation allowed'. An Additional calling Party number parameter is not present


SIP Parameter values INVITE: P-Asserted-Identity: present From: contains a URI that encodes an E.164 [i.1] address Privacy: none




ETSI

ETSI TS 101 572-2 V1.2.1 (2014-07)240


TSS reference IMS-SS/OIP-OIR/ Selection criteria PICS 6.3.3/6 AND PICS 6.3.2/1 Test Purpose name INVITE received. From header present, P-Asserted-Identity present. Privacy header 'id',


From header contains an URI that encodes an E.164 [i.1] Address a Privacy header is set to 'id', an INVITE with encapsulated IAM is sent. A Calling party number parameter is present and the address digits are derived from the P-Asserted-Identity header the Presentation restriction indicator is set to 'presentation restricted'. An Additional calling Party number parameter is not present

ISUP Parameter values IAM: Calling party Number Number incomplete indicator=Complete Numbering Plan Indicator=ISDN/Telephony (Recommendation E.164[i.1]) Nature of Address Indicator If CC encoded in the URI is equal to the CC of the country where MGCF is located AND the next BICC/ISUP node is located in the same country then national (significant) number else international number Screening indicator=Network Provided Presentation restriction=restricted Address signal derived from the P-Asserted-Identity if NOA is "national (significant) number" then set to "NDC" + "SN" If NOA is "international number" then set to "CC"+" NDC"+"SN"

SIP Parameter values INVITE: P-Asserted-Identity: present From: contains a URI that encodes an E.164 [i.1] address Privacy: id


INVITE � � IAM 100 Trying �


ETSI

ETSI TS 101 572-2 V1.2.1 (2014-07)241


TSS reference IMS-SS/OIP-OIR/ Selection criteria PICS 6.3.3/6 AND PICS 6.3.2/1 Test Purpose name INVITE received. From header present, P-Asserted-Identity present. Privacy header 'user',


From header contains an URI that encodes an E.164 [i.1] Address a Privacy header is set to 'user', an INVITE with encapsulated IAM is sent. A Calling party number parameter is present and the address digits are derived from the P-Asserted-Identity header the Presentation restriction indicator is set to 'presentation restricted'. An Additional calling Party number parameter is not present


SIP Parameter values INVITE: P-Asserted-Identity: present From: contains a URI that encodes an E.164 [i.1] address Privacy: user




ETSI

ETSI TS 101 572-2 V1.2.1 (2014-07)242


TSS reference IMS-SS/OIP-OIR/ Selection criteria PICS 6.3.3/6 AND PICS 6.3.2/1 Test Purpose name INVITE received. From header present, P-Asserted-Identity present. Privacy header

'header', additional calling party number omitted Test Purpose Ensure that on receipt of an INVITE request the P-Asserted-Identity is present and the

From header contains an URI that encodes an E.164 [i.1] Address a Privacy header is set to 'header', an INVITE with encapsulated IAM is sent. A Calling party number parameter is present and the address digits are derived from the P-Asserted-Identity header the Presentation restriction indicator is set to 'presentation restricted'. An Additional calling Party number parameter is not present


SIP Parameter values INVITE: P-Asserted-Identity: present From: contains a URI that encodes an E.164 [i.1] address Privacy: header





TSS reference IMS-SS/OIP-OIR/ Selection criteria PICS 6.3.2/1 Test Purpose name Calling party number not received, Additional calling party number not received,

unavailable From header is sent Test Purpose Ensure that on receipt of an INVITE with encapsulated IAM and no Calling party number

and no Additional calling party number is present, an INVITE is sent. A P-Asserted-Identity is not present and the URI of the From header is set to 'sip:[email protected]'

ISUP Parameter values IAM: Calling party number not present Generic number (Additional calling party number) not present

SIP Parameter values INVITE: From: sip:[email protected] P-Asserted-Identity not present




ETSI

ETSI TS 101 572-2 V1.2.1 (2014-07)243


TSS reference IMS-SS/OIP-OIR/ Selection criteria PICS 6.3.2/1 Test Purpose name Calling party number not received, Additional calling party number received presentation

allowed, From header containing a E.164 [i.1] URI is sent Test Purpose Ensure that on receipt of an INVITE with encapsulated IAM and no Calling party number is

present and an Additional calling party number is present, an INVITE is sent. A P-Asserted-Identity is not present and the URI of the From header is derived from the additional calling party number or is network provided

ISUP Parameter values IAM: Calling party number not present Generic number (Additional calling party number) present presentation allowed

SIP Parameter values INVITE: From: derived from the additional calling party number or network provided P-Asserted-Identity not present





TSS reference IMS-SS/OIP-OIR/ Selection criteria PICS 6.3.2/1 Test Purpose name Calling party number not received, Additional calling party number received presentation

restricted, unavailable From header is sent Test Purpose Ensure that on receipt of an INVITE with encapsulated IAM and no Calling party number

and an Additional calling party number is present the Presentation restriction indicator is set to 'presentation restricted', an INVITE is sent. A P-Asserted-Identity is not present and the URI of the From header is set to 'sip:[email protected]'

ISUP Parameter values IAM: Calling party number not present Generic number (Additional calling party number) present presentation restricted

SIP Parameter values INVITE: From: sip:[email protected] P-Asserted-Identity not present




ETSI

ETSI TS 101 572-2 V1.2.1 (2014-07)244


TSS reference IMS-SS/OIP-OIR/ Selection criteria PICS 6.3.2/1 Test Purpose name Calling party number received presentation allowed, Additional calling party number not

received, P-Asserted-Identity header and From header are sent Test Purpose Ensure that on receipt of an INVITE with encapsulated IAM and a Calling party number

Presentation restriction indicator is set to 'presentation allowed' and an Additional calling party number is not present, an INVITE is sent. A P-Asserted-Identity is present the URI is derived from the address signals of the calling party number and the URI of the From header is derived from the address signals of the calling party number. A Privacy header is not present or if present the value is not equal to 'id'

ISUP Parameter values IAM: Calling party number present presentation allowed Generic number (Additional calling party number) not present

SIP Parameter values INVITE: From derived from the calling party number P-Asserted-Identity derived from the calling party number Privacy not 'id' or Privacy header not present





TSS reference IMS-SS/OIP-OIR/ Selection criteria PICS 6.3.2/1 Test Purpose name Calling party number received presentation allowed, Additional calling party number

received presentation allowed, P-Asserted-Identity header and From header are sent Test Purpose Ensure that on receipt of an INVITE with encapsulated IAM and a Calling party number

Presentation restriction indicator is set to 'presentation allowed' and an Additional calling party number is present the Presentation restriction indicator is set to 'presentation allowed', an INVITE is sent. A P-Asserted-Identity is present the URI is derived from the address signals of the calling party number and the URI of the From header is derived from the address signals of the additional calling party number. A Privacy header is not present or if present the value is not equal to 'id'

ISUP Parameter values IAM: Calling party number present presentation allowed Generic number (Additional calling party number) present presentation allowed

SIP Parameter values INVITE: From derived from the additional calling party number P-Asserted-Identity derived from the calling party number Privacy not 'id' or Privacy header not present




ETSI

ETSI TS 101 572-2 V1.2.1 (2014-07)245


TSS reference IMS-SS/OIP-OIR/ Selection criteria PICS 6.3.2/1 Test Purpose name Calling party number received presentation allowed, Additional calling party number

received presentation restricted, P-Asserted-Identity header and From header are sent Test Purpose Ensure that on receipt of an INVITE with encapsulated IAM and a Calling party number

Presentation restriction indicator is set to 'presentation allowed' and an Additional calling party number is present the Presentation restriction indicator is set to 'presentation restricted', an INVITE is sent. A P-Asserted-Identity is present the URI is derived from the address signals of the calling party number and the URI of the From header is derived from the address signals of the calling party number. A Privacy header is not present or if present the value is not equal to 'id'

ISUP Parameter values IAM: Calling party number present presentation allowed Generic number (Additional calling party number) present presentation restricted

SIP Parameter values INVITE: From derived from the calling party number P-Asserted-Identity derived from the calling party number Privacy not 'id' or Privacy header not present





TSS reference IMS-SS/OIP-OIR/ Selection criteria PICS 6.3.2/1 Test Purpose name Calling party number received presentation restricted, Additional calling party number not

received, P-Asserted-Identity header and From header are sent Test Purpose Ensure that on receipt of an INVITE with encapsulated IAM and a Calling party number

Presentation restriction indicator is set to 'presentation restricted' and an Additional calling party number is not present, an INVITE is sent. A P-Asserted-Identity is present the URI is derived from the address signals of the calling party number and the URI of the From header is ser to 'sip:[email protected]'. A Privacy header is present the value is equal to 'id'

ISUP Parameter values IAM: Calling party number present presentation restricted Generic number (Additional calling party number) not present

SIP Parameter values INVITE: From: sip:[email protected] P-Asserted-Identity derived from the calling party number Privacy: 'id'




ETSI

ETSI TS 101 572-2 V1.2.1 (2014-07)246


TSS reference IMS-SS/OIP-OIR/ Selection criteria PICS 6.3.2/1 Test Purpose name Calling party number received presentation restricted, Additional calling party number

received presentation allowed, P-Asserted-Identity header and From header are sent Test Purpose Ensure that on receipt of an INVITE with encapsulated IAM and a Calling party number

Presentation restriction indicator is set to 'presentation restricted' and an Additional calling party number is present the Presentation restriction indicator is set to 'presentation allowed', an INVITE is sent. A P-Asserted-Identity is present the URI is derived from the address signals of the calling party number and the URI of the From header is derived from the address signals of the additional calling party number. A Privacy header is present the value is equal to 'id'

ISUP Parameter values IAM: Calling party number present presentation restricted Generic number (Additional calling party number) present presentation allowed

SIP Parameter values INVITE: From derived from the additional calling party number P-Asserted-Identity derived from the calling party number Privacy: 'id'





TSS reference IMS-SS/OIP-OIR/ Selection criteria PICS 6.3.2/1 Test Purpose name Calling party number received presentation restricted, Additional calling party number

received presentation restricted, P-Asserted-Identity header and From header are sent Test Purpose Ensure that on receipt of an INVITE with encapsulated IAM and a Calling party number

Presentation restriction indicator is set to 'presentation restricted' and an Additional calling party number is present the Presentation restriction indicator is set to 'presentation restricted', an INVITE is sent. A P-Asserted-Identity is present the URI is derived from the address signals of the calling party number and the URI of the From header is set to the value 'sip:[email protected]'. A Privacy header is present the value is equal to 'id'

ISUP Parameter values IAM: Calling party number present presentation restricted Generic number (Additional calling party number) present presentation restricted

SIP Parameter values INVITE: From: sip:[email protected] P-Asserted-Identity derived from the calling party number Privacy: 'id'




ETSI

ETSI TS 101 572-2 V1.2.1 (2014-07)247

6.3.2 Terminating Identification Presentation (TIP) and Terminating Identification Restriction (TIR)


TSS reference IMS-SS/TIP-TIR/ Selection criteria PICS 6.3.1/2 AND PICS 6.3.2/2 Test Purpose name INVITE is sent the supported header contains the option tag 'from-change' Test Purpose Ensure that on receipt of an INVITE with encapsulated IAM and the Connected Line

Identity Request indicator in the Optional Forward Call Indicators parameter is set to 'requested', an INVITE is sent and the Supported header contains the option tag 'from-change'

ISUP Parameter values IAM: Optional Forward Call Indicators Connected Line Identity Request = requested

SIP Parameter values INVITE: Supported: from-change INVITE (IAM): from-change tag not present





TSS reference IMS-SS/TIP-TIR/ Selection criteria PICS 6.3.1/2 AND PICS 6.3.2/2 Test Purpose name 'from-change' tag not included in a received provisional response Test Purpose Ensure that on receipt of a provisional response and the 'from-change' tag is not included

the 200 OK INVITE with encapsulated ANM is sent as soon as the 200 OK (INVITE) is received


SIP Parameter values INVITE: Supported: from-change 180: from-change tag not included in the Supported header INVITE (IAM) / 180 : from-change tag not present


INVITE (IAM) � � INVITE 180 Ringing (ACM) � � 180 Ringing 200 OK (INVITE) (ANM)



ETSI

ETSI TS 101 572-2 V1.2.1 (2014-07)248


TSS reference IMS-SS/TIP-TIR/ Selection criteria PICS 6.3.1/2 AND PICS 6.3.2/2 Test Purpose name 'from-change' tag not included in a received final response Test Purpose Ensure that on receipt of a final successful response and the 'from-change' tag is not

included the 200 OK INVITE with encapsulated ANM is sent ISUP Parameter values IAM: Optional Forward Call Indicators

Connected Line Identity Request = requested SIP Parameter values INVITE: Supported: from-change

200: from-change tag not included in the Supported header INVITE (IAM) / 200: from-change tag not present


INVITE (IAM) � � INVITE 180 Ringing (ACM) � � 180 Ringing 200 OK INVITE (ANM) � � 200 OK (INVITE) ACK � � ACK



TSS reference IMS-SS/TIP-TIR/ Selection criteria PICS 6.3.1/2 AND PICS 6.3.2/2 Test Purpose name 'from-change' tag included in a received provisional response Test Purpose Ensure that on receipt of a provisional response and the 'from-change' tag is included the

timer TTIR1 is started. The 200 OK INVITE with encapsulated ANM is sent as soon as the UPDATE request is received and a Generic number with a Number qualifier indicator set to 'additional connected number' is present. The additional connected number is coded as follows:

Nature of Address Indicator If CC is equal to the country code of the country where SUT is located AND the next ISUP node is located in the same country, then set to

"national (significant) number" else set to

"international number" Number Incomplete Indicator = complete Numbering Plan Indicator = ISDN (Telephony) numbering plan (Recommendation E.164) Address Presentation Restricted Indicator = Privacy_VA as indicate in table 6.3.2-1 Screening Indicator = user provided, not verified Address Signals

If NOA is "national (significant) number" then set to NDC + SN. If NOA is "international number" then set to CC + NDC + SN

In addition a Connected number is present the address signal are derived from the P-Asserted-Identity in UPDATE request

ISUP Parameter values IAM: Optional Forward Call Indicators Connected Line Identity Request = requested ANM: Connected number Generic number - additional connected number

SIP Parameter values INVITE: Supported: from-change 180: from-change tag included in the Supported header INVITE (IAM) / 180: from-change tag not present


INVITE (IAM) � � INVITE 180 Ringing (ACM) � � 180 Ringing TTIR1 started � 200 OK (INVITE)

� ACK 200 OK INVITE (ANM) � � UPDATE ACK � � 200 OK (UPDATE)


ETSI

ETSI TS 101 572-2 V1.2.1 (2014-07)249


TSS reference IMS-SS/TIP-TIR/ Selection criteria PICS 6.3.1/2 AND PICS 6.3.2/2 Test Purpose name 'from-change' tag included in a received final response Test Purpose Ensure that on receipt of a final successful response and the 'from-change' tag is included

the timer TTIR1 is started. The 200 OK IVITE with encapsulated ANM is sent as soon as the UPDATE request is received and a Generic number with a Number qualifier indicator set to 'additional connected number' is present. The additional connected number is coded as follows:

Nature of Address Indicator If CC is equal to the country code of the country where SUT is located AND the next ISUP node is located in the same country, then set to

"national (significant) number" else set to

"international number" Number Incomplete Indicator = complete Numbering Plan Indicator = ISDN (Telephony) numbering plan (Recommendation E.164) Address Presentation Restricted Indicator = Privacy_VA as indicate in table 6.3.2-1 Screening Indicator = user provided, not verified Address Signals

If NOA is "national (significant) number" then set to NDC + SN. If NOA is "international number" then set to CC + NDC + SN

In addition a Connected number is present the address signal are derived from the P-Asserted-Identity in UPDATE request

ISUP Parameter values IAM: Optional Forward Call Indicators Connected Line Identity Request = requested ANM: Connected number Generic number - additional connected number




� ACK 200 OK INVITE (ANM) � � UPDATE ACK � � 200 OK (UPDATE)


Table 6.3.2-1: Mapping of Privacy value into Address presentation restriction indicator

Privacy_VA Privacy value Address Presentation Restricted Indicator Privacy_VA_01 Header Presentation restricted Privacy_VA_02 User Presentation restricted Privacy_VA_03 None Presentation allowed Privacy_VA_04 Id Presentation restricted Privacy_VA_05 Privacy header not present Presentation allowed

ETSI

ETSI TS 101 572-2 V1.2.1 (2014-07)250


TSS reference IMS-SS/TIP-TIR/ Selection criteria PICS 6.3.1/2 AND PICS 6.3.2/2 Test Purpose name Timer TTIR1 expires

Test Purpose Ensure that on receipt of a 200 OK (INVITE) and the 'from-change' tag is present in the Supported header the timer TTIR1 is started. After expiry of TTIR1 the 200 OK INVITE with

encapsulated ANM is sent ISUP Parameter values IAM: Optional Forward Call Indicators

Connected Line Identity Request = requested ANM: Connected number




� ACK 200 OK INVITE (ANM) � TTIR1 expired

ACK � Apply post test routine


TSS reference IMS-SS/TIP-TIR/ Selection criteria PICS 6.3.1/2 AND PICS 6.3.2/2 Test Purpose name Interworking of SIP Supported header into Optional forward call indicator Test Purpose Ensure that on receipt of an INVITE request and the Supported header contains the 'from-

change' tag, an INVITE with encapsulated IAM is sent. The Connected Line Identity Request indicator in the Optional Forward Call Indicators parameter is set to 'requested'


SIP Parameter values INVITE: Supported: from-change INVITE (IAM): from-change tag not present




ETSI

ETSI TS 101 572-2 V1.2.1 (2014-07)251


TSS reference IMS-SS/TIP-TIR/ Selection criteria PICS 6.3.1/2 AND PICS 6.3.2/2 Test Purpose name Mapping of Additional connected number presentation allowed into the From header in an

UPDATE request. Test Purpose Ensure that on receipt of a 200 OK INVITE with encapsulated ANM and a Generic number

additional connected number is present, a 200 OK (INVITE) is sent and the P-Asserted-Identity copied from the P-Called-Party-ID header and the 'from-change' tag in the Supported header is present. The 200 OK (INVITE) is followed by an UPDATE request, containing the 'additional connected number' received in the 200 OK INVITE with encapsulated ANM copied into the From header as described below Generic number Nature of Address Indicator

"national (significant) number" Add "+" CC (of the country where the IWU is located) to Generic Number Address Signals then map to user portion of URI scheme used

"international number" Map complete Generic Number Address Signals used prefixed with a "+" to user portion of URI scheme used

Address Presentation restriction indicator presentation allowed then no Privacy header present or not "header" or not "user"

Address Signals: "+" CC NDC SN mapped to user portion of URI scheme used The P-Asserted-Identity is derived from the Connected number as follows Connected number Nature of Address Indicator

"national (significant) number" Add "+" CC (of the country where the IWU is located) to Connected Number Address Signals then map to user portion of URI scheme used

"international number" Map complete Connected Number Address Signals used prefixed with a "+" to user portion of URI scheme used

Address Presentation restriction indicator presentation allowed then no Privacy header present or not "header" or not "user"

Address Signals: "+" CC NDC SN mapped to user portion of URI scheme used ISUP Parameter values IAM: Optional forward call indicator

Connected Line Identity Request = requested ANM: Generic number additional connected number Address Presentation restriction indicator = presentation allowed

SIP Parameter values INVITE: Supported: from-change 200 OK: P-Asserted-Identity Supported: from-change UPDATE: From: <derived from the additional connected number> INVITE (IAM) / 200: from-change tag not present


INVITE � � INVITE (IAM) 180 Ringing � � 180 Ringing (ACM) 200 OK (INVITE) � � 200 OK INVITE (ANM) � ACK UPDATE � 200 OK (UPDATE) �


ETSI

ETSI TS 101 572-2 V1.2.1 (2014-07)252


TSS reference IMS-SS/TIP-TIR/ Selection criteria PICS 6.3.1/2 AND PICS 6.3.2/2 Test Purpose name Mapping of Additional connected number presentation restricted into the From header in

an UPDATE request Test Purpose Ensure that on receipt of a 200 OK INVITE with encapsulated ANM and a Generic number

additional connected number is present, a 200 OK (INVITE) is sent and the P-Asserted-Identity copied from the P-Called-Party-ID header and the 'from-change' tag in the Supported header is present. The 200 OK (INVITE) is followed by an UPDATE request, containing the 'additional connected number' received in the ANM copied into the From header as described below Generic number Nature of Address Indicator

"national (significant) number" Add "+" CC (of the country where the IWU is located) to Generic Number Address Signals then map to user portion of URI scheme used

"international number" Map complete Generic Number Address Signals used prefixed with a "+" to user portion of URI scheme used

Address Presentation restriction indicator presentation restricted then Privacy: header

Address Signals: "+" CC NDC SN mapped to user portion of URI scheme used The P-Asserted-Identity is derived from the Connected number as follows Connected number Nature of Address Indicator

"national (significant) number" Add "+" CC (of the country where the IWU is located) to Connected Number Address Signals then map to user portion of URI scheme used

"international number" Map complete Connected Number Address Signals used prefixed with a "+" to user portion of URI scheme used

Address Presentation restriction indicator presentation restricted then Privacy: header

Address Signals: "+" CC NDC SN mapped to user portion of URI scheme used ISUP Parameter values IAM: Optional forward call indicator

Connected Line Identity Request = requested ANM: Generic number additional connected number Address Presentation restriction indicator = presentation restricted

SIP Parameter values INVITE: Supported: from-change 200 OK: P-Asserted-Identity Supported: from-change UPDATE: From: <derived from the additional connected number> P-Asserted-Identity: <derived from the connected number> INVITE (IAM) / 200: from-change tag not present


INVITE � � INVITE (IAM) 180 Ringing � � 180 Ringing (ACM) 200 OK (INVITE) � � 200 OK INMVITE (ANM) � ACK UPDATE � 200 OK (UPDATE) �


ETSI

ETSI TS 101 572-2 V1.2.1 (2014-07)253

6.3.3 Communication Diversion (CDIV)


TSS reference IMS-SS/CDIV/ Selection criteria PICS 6.3.1/2 AND PICS 6.3.2/5 Test Purpose name Mapping of 181 hi-targeted-to-uri into 181 (Call Is Being Forwarded) or 183 Session

Progress with encapsulated ACM Redirection number Test Purpose Ensure that on receipt of 181 (Call Is Being Forwarded) an 181 (Call Is Being Forwarded)

or 183 Session Progress with encapsulated ACM is sent. The History-Info entry containing a cause parameter is mapped into the Redirection number: • If CC of the hi-targeted-to-uri is equal the country code where the SUT is located:

Nature of address indicator is set to 'national (significant) number', '+' and the country code is removed from the digit string and sent in the Address signal of the Redirection number.

• If the country code of the hi-targeted-to-uri is not equal the country code where the SUT is located: Nature of address indicator is set to 'international number' '+' is removed from the digit string and sent in the Address signal of the Redirection number

ISUP Parameter values ACM: Generic Notification Redirection number Nature of address indicator Address signal Derived from the last History-Info entry

SIP Parameter values 181: History-Info: <sip:any proper URI>; index=1, <sip:any proper URI;cause=any>; index=1.1 183/181 (ACM): History-Info not present


INVITE (IAM) � � INVITE � 181 Call Is Being Forwarded CASE A 183 Session Progress (ACM) � CASE B 181 Call Is Being Forwarded (ACM) �


TP number TP_403_001A Reference [1], clause 7.3.1 [2], clauses 7.5.4.2.1, table, 7.5.4.2.1.2

TSS reference IMS-SS/CDIV/ Selection criteria PICS 6.3.1/2 AND PICS 6.3.2/5 Test Purpose name Sending of Generic Notification in ACM Test Purpose Ensure that on receipt of 181 (Call Is Being Forwarded) an 183 Session Progress or 183

Session Progress with encapsulated ACM is sent. A Generic Notification parameter is sent in the encapsulated ACM set to 'call is diverting'.

ISUP Parameter values ACM: Generic Notification call is diverting

SIP Parameter values 181: History-Info: <sip:any proper URI>; index=1, <sip:any proper URI;cause=any>; index=1.1 183/181 (ACM): History-Info not present




ETSI

ETSI TS 101 572-2 V1.2.1 (2014-07)254


TSS reference IMS-SS/CDIV/ Selection criteria PICS 6.3.1/2 AND PICS 6.3.2/5 Test Purpose name Mapping of 181 escaped Privacy header into 181 (Call Is Being Forwarded) or 183 Session

Progress with encapsulated ACM Redirection number restriction Test Purpose Ensure that on receipt of 181 (Call Is Being Forwarded), a 181 (Call Is Being Forwarded) or

183 Session Progress with encapsulated ACM is sent. The Redirection number restriction is set according the escaped Privacy header in the last History entry as indicated in table 6.3.3-1

ISUP Parameter values ACM: Redirection number restriction= PRES_restr SIP Parameter values 181:

History-Info: <sip:any proper URI>; index=1, <sip:any proper URI;cause=any value?Privacy=Priv-value >; index=1.1 181/183 (ACM): History-Info not present





TSS reference IMS-SS/CDIV/ Selection criteria PICS 6.3.1/2 AND PICS 6.3.2/5 Test Purpose name Mapping of 181 Privacy header into 181 (Call Is Being Forwarded) or 183 Session

Progress with encapsulated ACM Redirection number restriction Test Purpose Ensure that on receipt of 181 (Call Is Being Forwarded), a 181 (Call Is Being Forwarded) or

183 Session Progress with encapsulated ACM is sent. The Redirection number restriction is set according the Privacy header as indicated in table 6.3.3-1


Privacy=Priv-value History-Info: <sip:any proper URI>; index=1, <sip:any proper URI;cause=any value>; index=1.1 181/183 (ACM): History-Info not present


INVITE (IAM) � � INVITE � 181 Call Is Being Forwarded CASE A 181 Call Is Being Forwarded (ACM)

�

CASE B 183 Session Progress (ACM) �


Table 6.3.3-1: Mapping of Privacy value into Redirection number restriction

CAUSE Priv-value PRES_restr VA_01 history Presentation restricted VA_02 session Presentation restricted VA_03 header Presentation restricted VA_04 none or absent Presentation allowed or absent

ETSI

ETSI TS 101 572-2 V1.2.1 (2014-07)255


TSS reference IMS-SS/CDIV/ Selection criteria PICS 6.3.1/2 AND PICS 6.3.2/5 Test Purpose name Mapping of 181 Privacy header into 181 (Call Is Being Forwarded) or 183 Session

Progress with encapsulated ACM Notification subscription options Test Purpose Ensure that on receipt of 181 (Call Is Being Forwarded) containing a Privacy header, a 181

(Call Is Being Forwarded) or 183 Session Progress with encapsulated ACM is sent. The Notification subscription options in the Call Diversion Information parameter is set according the Privacy header in the message body as indicated in table 6.3.3-2

ISUP Parameter values ACM: Call Diversion Information Notification subscription options=SUBS_options

SIP Parameter values 181: Privacy: Priv-value History-Info: <sip:any proper URI;cause=any value>; index=1, <sip:any proper URI>; index=1.1 181/183 (ACM): History-Info not present



�



Table 6.3.3-2: Mapping of Privacy value into Notification subscription options

CAUSE Priv-value SUBS_options VA_01 history presentation not allowed VA_02 session presentation not allowed VA_03 header presentation not allowed VA_04 None or absent Presentation allowed with redirection number

ETSI

ETSI TS 101 572-2 V1.2.1 (2014-07)256


TSS reference IMS-SS/CDIV/ Selection criteria PICS 6.3.1/2 AND PICS 6.3.2/5 Test Purpose name Mapping of 181 escaped Privacy header into 181 (Call Is Being Forwarded) with or 183

Session Progress encapsulated ACM Notification subscription options Test Purpose Ensure that on receipt of 181 (Call Is Being Forwarded) or 183 Session Progress

containing an escaped Privacy header field in the last hi-targeted-to-uri, a 181 (Call Is Being Forwarded) with encapsulated ACM is sent. The Notification subscription options in the Call Diversion Information parameter is set according the escaped Privacy header in the last History entry as indicated in table 6.3.3-3


SIP Parameter values 181: History-Info: <sip:any proper URI >; index=1, <sip:any proper URI;cause=any value?Privacy=Priv-value>; index=1.1 181/183 (ACM): History-Info not present



�



Table 6.3.3-3: Mapping of Privacy value into Notification subscription options

CAUSE Priv-value SUBS_options VA_01 history presentation allowed without redirection number VA_02 session presentation allowed without redirection number VA_03 header presentation allowed without redirection number VA_04 None or absent Presentation allowed with redirection number

ETSI

ETSI TS 101 572-2 V1.2.1 (2014-07)257


TSS reference IMS-SS/CDIV/ Selection criteria PICS 6.3.1/2 AND PICS 6.3.2/5 Test Purpose name Mapping of 181 hi-targeted-to-uri into 181 (Call Is Being Forwarded) or 183 Session

Progress with encapsulated ACM Redirecting Reason Test Purpose Ensure that on receipt of 181 (Call Is Being Forwarded) a 181 (Call Is Being Forwarded) or

183 Session Progress with encapsulated ACM is sent. The cause parameter of the last hi-entry is mapped into the Redirecting reason in the Call Diversion Information parameter is set as indicated in table 6.3.3-4

ISUP Parameter values ACM: Redirection number Call Diversion Information Redirecting reason = Redirecting_Reason

SIP Parameter values 181: History-Info: <sip:any proper URI>; index=1, <sip:any proper URI;cause=CAUSE_value>; index=1.1 181/183 (ACM): History-Info not present



�



Table 6.3.3-4: Mapping of cause parameter into Redirecting reason

CAUSE CAUSE_value Redirecting_Reason VA_01 404 Unknown VA_02 302 Unconditional VA_03 486 User busy VA_04 408 No reply VA_05 480 Deflection immediate VA_06 503 Mobile subscriber not reachable VA_07 487 Deflection during alerting

ETSI

ETSI TS 101 572-2 V1.2.1 (2014-07)258


TSS reference IMS-SS/CDIV/ Selection criteria PICS 6.3.5/3 AND PICS 6.3.1/2 AND PICS 6.3.2/5 Test Purpose name Mapping of 181 hi-targeted-to-uri cause parameter into 181 Call Is Being Forwarded with or

183 Session Progress encapsulated CPG Event indicator Test Purpose Ensure that on receipt of 181 (Call Is Being Forwarded) a 181 (Call Is Being Forwarded) or

183 Session Progress with encapsulated CPG is sent. The Event indicator is set to 'Redirecting_Reason' as indicated in table 6.3.3-5

ISUP Parameter values CPG: Event=Redirecting_Reason

SIP Parameter values 181: History-Info: <sip:any proper URI>; index=1, <sip:any proper URI;cause=CAUSE_value>; index=1.1 181/183 (CPG): History-Info not present


INVITE (IAM) � � INVITE 180 Ringing (ACM) � � 180 Ringing � 181 Call Is Being Forwarded CASE A 181 Call Is Being Forwarded (CPG)

�

CASE B 183 Session Progress (CPG) �


Table 6.3.3-5: Mapping of cause parameter into Event indicator

CAUSE_value Redirecting_Reason VA_01 486 CFB (national use) VA_02 408 CFNR (national use) VA_03 302 CFU (national use)

ETSI

ETSI TS 101 572-2 V1.2.1 (2014-07)259


TSS reference IMS-SS/CDIV/ Selection criteria PICS 6.3.1/2 AND PICS 6.3.2/5 Test Purpose name Mapping of 181 hi-targeted-to-uri into 181 Call Is Being Forwarded or 183 Session

Progress with encapsulated CPG Redirection number Test Purpose Ensure that on receipt of 181 (Call Is Being Forwarded) a 181 (Call Is Being Forwarded) or

183 Session Progress with the encapsulated CPG is sent. The History-Info entry containing a cause parameter is mapped into the Redirection number: • If CC of the hi-targeted-to-uri is equal the country code where the SUT is located:



ISUP Parameter values CPG: Redirection number Nature of address indicator Address signal Derived from the last History-Info entry

SIP Parameter values 181: History-Info: <sip:any proper URI>; index=1, <sip:any proper URI;cause=any>; index=1.1 181/183 (CPG): History-Info not present



�



ETSI

ETSI TS 101 572-2 V1.2.1 (2014-07)260


TSS reference IMS-SS/CDIV/ Selection criteria PICS 6.3.1/2 AND PICS 6.3.2/5 Test Purpose name Sending of Generic Notification in the encapsulated CPG Test Purpose Ensure that on receipt of 181 (Call Is Being Forwarded) containing a History-Info header a

181 (Call Is Being Forwarded) or 183 Session Progress with the encapsulated CPG is sent. A Generic Notification parameter is sent in the CPG message set to 'call is diverting'.

ISUP Parameter values CPG: Generic Notification call is diverting




�



TP number TP_403_008B Reference [1], clause 7.3.1 [2], clauses 7.5.4.2.1, table, 7.5.4.2.1.2

TSS reference IMS-SS/CDIV/ Selection criteria PICS 6.3.1/2 AND PICS 6.3.2/5 Test Purpose name Sending of CPG Event indicator 'Progress' Test Purpose Ensure that on receipt of 181 (Call Is Being Forwarded) a 181 (Call Is Being Forwarded) or

183 Session Progress with the encapsulated CPG is sent. The Event indicator in the encapsulated CPG is set to 'Progress'

ISUP Parameter values CPG: Event indicator Progress




�



ETSI

ETSI TS 101 572-2 V1.2.1 (2014-07)261


TSS reference IMS-SS/CDIV/ Selection criteria PICS 6.3.1/2 AND PICS 6.3.2/5 Test Purpose name Mapping of 181 escaped Privacy header into 181 Call Is Being Forwarded or 183 Session

Progress with encapsulated CPG Redirection number restriction Test Purpose Ensure that on receipt of 181 (Call Is Being Forwarded), a 181 (Call Is Being Forwarded) or

183 Session Progress with encapsulated CPG is sent. The Redirection number restriction is set according the escaped Privacy header in the last History entry as indicated in table 6.3.3-1

ISUP Parameter values CPG: Redirection number restriction = PRES_restr SIP Parameter values 181:

History-Info: <sip:any proper URI>; index=1, <sip:any proper URI;cause=any value?Privacy=Priv-value>; index=1.1 181/183 (CPG): History-Info not present



�




TSS reference IMS-SS/CDIV/ Selection criteria PICS 6.3.1/2 AND PICS 6.3.2/5 Test Purpose name Mapping of 181 Privacy header into early 181 Call Is Being Forwarded or 183 Session

Progress with encapsulated CPG Redirection number restriction Test Purpose Ensure that on receipt of 181 (Call Is Being Forwarded), a 181 Call Is Being Forwarded

with or 183 Session Progress encapsulated CPG is sent. The Redirection number restriction is set according the Privacy header as indicated in table 6.3.3-1.

ISUP Parameter values CPG: Redirection number restriction = PRES_restr SIP Parameter values 181:

Privacy=Priv-value History-Info: <sip:any proper URI>; index=1, <sip:any proper URI;cause=any value>; index=1.1 181/183 (CPG): History-Info not present



�



ETSI

ETSI TS 101 572-2 V1.2.1 (2014-07)262


TSS reference IMS-SS/CDIV/ Selection criteria PICS 6.3.1/2 AND PICS 6.3.2/5 Test Purpose name Mapping of 181 Privacy header into 181 Call Is Being Forwarded or 183 Session Progress

with encapsulated CPG Notification subscription options Test Purpose Ensure that on receipt of 181 (Call Is Being Forwarded) containing a Privacy header, a 181

(Call Is Being Forwarded) or 183 Session Progress with encapsulated CPG is sent. The Notification subscription options in the Call Diversion Information parameter is set according the Privacy header in the message body as indicated in table 6.3.3-2

ISUP Parameter values CPG: Call Diversion Information Notification subscription options=SUBS_options

SIP Parameter values 181: Privacy: Priv-value History-Info: <sip:any proper URI>; index=1, <sip:any proper URI;cause=any value>; index=1.1 181/183 (CPG): History-Info not present



�




TSS reference IMS-SS/CDIV/ Selection criteria PICS 6.3.1/2 AND PICS 6.3.2/5 Test Purpose name Mapping of 181 escaped Privacy header into 181 Call Is Being Forwarded or 183 Session

Progress with encapsulated CPG Notification subscription options Test Purpose Ensure that on receipt of 181 (Call Is Being Forwarded) containing an escaped Privacy

header field in the last hi-targeted-to-uri, a 181 Call Is Being Forwarded or 183 Session Progress with encapsulated CPG is sent. The Notification subscription options in the Call Diversion Information parameter is set according the escaped Privacy header in the last History entry as indicated in table 6.3.3-3


SIP Parameter values 181: History-Info: <sip:any proper URI>; index=1, <sip:any proper URI;cause=any value?Privacy=Priv-value>; index=1.1 181/183 (CPG): History-Info not present



�



ETSI

ETSI TS 101 572-2 V1.2.1 (2014-07)263


TSS reference IMS-SS/CDIV/ Selection criteria PICS 6.3.1/2 AND PICS 6.3.2/5 Test Purpose name Mapping of 181 hi-targeted-to-uri into 181 Call Is Being Forwarded or 183 Session

Progress with encapsulated CPG Redirecting Reason Test Purpose Ensure that on receipt of 181 (Call Is Being Forwarded) a 181 Call Is Being Forwarded or

183 Session Progress with encapsulated CPG is sent. The History-Info entry containing a cause parameter is mapped into the Redirecting reason in the Call Diversion Information parameter is set as indicated in table 6.3.3-4

ISUP Parameter values CPG: Call Diversion Information Redirecting reason= Redirecting_Reason

SIP Parameter values 181: History-Info: <sip:any proper URI>; index=1, <sip:any proper URI;cause=CAUSE_value>; index=1.1 181/183 (CPG): History-Info not present



�




TSS reference IMS-SS/CDIV/ Selection criteria PICS 6.3.1/2 AND PICS 6.3.2/5 Test Purpose name Mapping of 180 hi-targeted-to-uri into a 180 (Ringing) with encapsulated ACM Redirection

number Test Purpose Ensure that on receipt of 180 (Ringing) a 180 (Ringing) with encapsulated ACM (subscriber

free) is sent. The last History-Info entry containing a cause parameter is mapped into the Redirection number: • If CC of the hi-targeted-to-uri is equal the country code where the SUT is located:



ISUP Parameter values ACM: Redirection number Nature of address indicator Address signal Derived from the last History-Info entry

SIP Parameter values 180: History-Info: <sip:any proper URI>; index=1, <sip:any proper URI;cause=any>; index=1.1 180 (ACM): History-Info not present


INVITE (IAM) � � INVITE 180 Ringing (ACM) � � 180 Ringing


ETSI

ETSI TS 101 572-2 V1.2.1 (2014-07)264


TSS reference IMS-SS/CDIV/ Selection criteria PICS 6.3.1/2 AND PICS 6.3.2/5 Test Purpose name Sending of Generic Notification in an ACM free Test Purpose Ensure that on receipt of 180 (Ringing) a 180 Ringing with an encapsulated ACM

(subscriber free) is sent. The last History-Info entry containing a cause parameter. A Generic Notification parameter is sent in the ACM set to 'call is diverting'.

ISUP Parameter values ACM: Backward call indicator Called party status=subscriber free Generic Notification call is diverting

SIP Parameter values 180: History-Info: <sip:any proper URI>; index=1, <sip:any proper URI;cause=any>; index=1.1 180 (ACM): History-Info not present





TSS reference IMS-SS/CDIV/ Selection criteria PICS 6.3.1/2 AND PICS 6.3.2/5 Test Purpose name Mapping of 180 escaped Privacy header into a 180 (Ringing) with encapsulated ACM

Redirection number restriction Test Purpose Ensure that on receipt of 180 (Ringing), a 180 (Ringing) with encapsulated ACM

(subscriber free) is sent. The Redirection number restriction is set according the escaped Privacy header in the last History entry as indicated in table 6.3.3-1


History-Info: <sip:any proper URI>; index=1, <sip:any proper URI;cause=any?Privacy=Priv-value>; index=1.1 180 (ACM): History-Info not present




ETSI

ETSI TS 101 572-2 V1.2.1 (2014-07)265


TSS reference IMS-SS/CDIV/ Selection criteria PICS 6.3.1/2 AND PICS 6.3.2/5 Test Purpose name Mapping of 180 Privacy header into a 180 (Ringing) with encapsulated ACM Redirection

number restriction Test Purpose Ensure that on receipt of 180 (Ringing), a 180 (Ringing) with encapsulated ACM

(subscriber free) is sent. The Redirection number restriction is set according the Privacy header as indicated in table 6.3.3-1


Privacy=Priv-value History-Info: <sip:any proper URI>; index=1, <sip:any proper URI;cause=any value>; index=1.1 180 (ACM): History-Info not present





TSS reference IMS-SS/CDIV/ Selection criteria PICS 6.3.1/2 AND PICS 6.3.2/5 Test Purpose name Mapping of 180 Privacy header into a 180 (Ringing) with encapsulated ACM Notification

subscription options Test Purpose Ensure that on receipt of 180 (Ringing) containing a Privacy header, a 180 (Ringing) with

encapsulated ACM (subscriber free) is sent. The Notification subscription options in the Call Diversion Information parameter is set according the Privacy header in the message body as indicated in table 6.3.3-2


SIP Parameter values 180: Privacy: Priv-value History-Info: <sip:any proper URI>; index=1, <sip:any proper URI;cause=any value>; index=1.1 180 (ACM): History-Info not present




ETSI

ETSI TS 101 572-2 V1.2.1 (2014-07)266


TSS reference IMS-SS/CDIV/ Selection criteria PICS 6.3.1/2 AND PICS 6.3.2/5 Test Purpose name Mapping of 181 escaped Privacy header into a 180 (Ringing) with encapsulated ACM

Notification subscription options Test Purpose Ensure that on receipt of 180 (Ringing) containing an escaped Privacy header field in the

last hi-targeted-to-uri, a 180 (Ringing) with encapsulated ACM (subscriber free) is sent. The Notification subscription options in the Call Diversion Information parameter is set according the escaped Privacy header in the last History entry as indicated in table 6.3.3-3


SIP Parameter values 180: History-Info: <sip:any proper URI>; index=1, <sip:any proper URI;cause=any value?Privacy=Priv-value>; index=1.1 180 (ACM): History-Info not present





TSS reference IMS-SS/CDIV/ Selection criteria PICS 6.3.1/2 AND PICS 6.3.2/5 Test Purpose name Mapping of 180 hi-targeted-to-uri into a 180 (Ringing) with encapsulated ACM Redirecting

Reason Test Purpose Ensure that on receipt of 180 (Ringing) a 180 (Ringing) with encapsulated ACM (subscriber

free) is sent. The last History-Info entry containing a cause parameter is mapped into the Redirecting reason in the Call Diversion Information parameter is set as indicated in table 6.3.3-4

ISUP Parameter values ACM: Call Diversion Information Redirecting reason= Redirecting_Reason

SIP Parameter values 180: History-Info: <sip:any proper URI;cause=CAUSE_value>; index=1, <sip:any proper URI>; index=1.1 180 (ACM): History-Info not present




ETSI

ETSI TS 101 572-2 V1.2.1 (2014-07)267


TSS reference IMS-SS/CDIV/ Selection criteria PICS 6.3.1/2 AND PICS 6.3.2/5 Test Purpose name Mapping of 180 hi-targeted-to-uri into a 180 (Ringing) with encapsulated CPG Redirection

number Test Purpose Ensure that on receipt of 180 (Ringing) a 180 (Ringing) with encapsulated CPG Alerting is

sent. The last History-Info entry containing a cause parameter is mapped into the Redirection number: • If CC of the hi-targeted-to-uri is equal the country code where the SUT is located:



ISUP Parameter values CPG: Redirection number Nature of address indicator Address signal Derived from the last History-Info entry

SIP Parameter values 180: History-Info: <sip:any proper URI>; index=1, <sip:any proper URI;cause=any>; index=1.1 180 (CPG): History-Info not present


INVITE (IAM) � � INVITE 181 Call Is Being Forwarded (ACM)

� � 181 Call Is Being Forwarded



TSS reference IMS-SS/CDIV/ Selection criteria PICS 6.3.1/2 AND PICS 6.3.2/5 Test Purpose name Sending of Generic Notification in an encapsulated CPG after 180 Test Purpose Ensure that on receipt of 180 (Ringing) an encapsulated CPG Alerting is sent. The last

History-Info entry containing a cause parameter. The CPG contains the Generic Notification parameter set to 'call is diverting'.

ISUP Parameter values CPG: Generic Notification call is diverting

SIP Parameter values 180: History-Info: <sip:any proper URI>; index=1, <sip:any proper URI;cause=any>; index=1.1 180 (CPG): History-Info not present





ETSI

ETSI TS 101 572-2 V1.2.1 (2014-07)268

TP number TP_403_020B Reference [1], clause 7.3.1 [2], clauses 7.5.4.2.1, table, 7.5.4.2.1.9

TSS reference IMS-SS/CDIV/ Selection criteria PICS 6.3.1/2 AND PICS 6.3.2/5 Test Purpose name Sending of Event indicator 'Alerting' in an encapsulated CPG after 180 Test Purpose Ensure that on receipt of 180 (Ringing) an encapsulated CPG Alerting is sent. The last

History-Info entry containing a cause parameter. The Event indicator in the encapsulated CPG message is set to 'Alerting'.

ISUP Parameter values CPG: Event=Alerting SIP Parameter values 180:

History-Info: <sip:any proper URI>; index=1, <sip:any proper URI;cause=any>; index=1.1 180 (CPG): History-Info not present






TSS reference IMS-SS/CDIV/ Selection criteria PICS 6.3.1/2 AND PICS 6.3.2/5 Test Purpose name Mapping of 180 escaped Privacy header into a 180 (Ringing) with encapsulated CPG

Redirection number restriction Test Purpose Ensure that on receipt of 180 (Ringing), a 180 (Ringing) with encapsulated CPG Alerting is

sent. The Redirection number restriction is set according the escaped Privacy header in the last History entry as indicated in table 6.3.3-1

ISUP Parameter values CPG: Redirection number restriction= PRES_restr SIP Parameter values 180:

History-Info: <sip:any proper URI>; index=1, <sip:any proper URI;cause=any?Privacy=Priv-value>; index=1.1 180 (CPG): History-Info not present





ETSI

ETSI TS 101 572-2 V1.2.1 (2014-07)269


TSS reference IMS-SS/CDIV/ Selection criteria PICS 6.3.1/2 AND PICS 6.3.2/5 Test Purpose name Mapping of 180 Privacy header into CPG Redirection number restriction Test Purpose Ensure that on receipt of 180 (Ringing), a 180 Ringing with encapsulated CPG Alerting is

sent. The Redirection number restriction is set according the Privacy header as indicated in table 6.3.3-1

ISUP Parameter values CPG: Redirection number restriction= PRES_restr SIP Parameter values 180:

Privacy=Priv-value History-Info: <sip:any proper URI>; index=1, <sip:any proper URI;cause=any value>; index=1.1 180 (CPG): History-Info not present




180 Ringing (CPG-Ringing)

� � 180 Ringing



TSS reference IMS-SS/CDIV/ Selection criteria PICS 6.3.1/2 AND PICS 6.3.2/5 Test Purpose name Mapping of 180 Privacy header into CPG Notification subscription options Test Purpose Ensure that on receipt of 180 (Ringing) containing a Privacy header, a 180 Ringing with

encapsulated CPG Alerting is sent. The Notification subscription options in the Call Diversion Information parameter is set according the Privacy header in the message body as indicated in table 6.3.3-2


SIP Parameter values 180: Privacy: Priv-value History-Info: <sip:any proper URI>; index=1, <sip:any proper URI;cause=any value>; index=1.1 180 (CPG): History-Info not present





ETSI

ETSI TS 101 572-2 V1.2.1 (2014-07)270


TSS reference IMS-SS/CDIV/ Selection criteria PICS 6.3.1/2 AND PICS 6.3.2/5 Test Purpose name Mapping of 180 escaped Privacy header into CPG Notification subscription options Test Purpose Ensure that on receipt of 180 (Ringing) containing an escaped Privacy header field in the

last hi-targeted-to-uri, a 180 (Ringing) with encapsulated CPG Alerting is sent. The Notification subscription options in the Call Diversion Information parameter is set according the escaped Privacy header in the last History entry as indicated in table 6.3.3-3


SIP Parameter values 180: History-Info: <sip:any proper URI>; index=1, <sip:any proper URI;cause=any value?Privacy=Priv-value>; index=1.1 180 (CPG): History-Info not present




180 Ringing (CPG - Alerting)

� � 180 Ringing



TSS reference IMS-SS/CDIV/ Selection criteria PICS 6.3.1/2 AND PICS 6.3.2/5 Test Purpose name Mapping of 180 hi-targeted-to-uri into CPG Redirecting Reason Test Purpose Ensure that on receipt of 180 (Ringing) a 180 (Ringing) with encapsulated CPG Alerting is

sent. The last History-Info entry containing a cause parameter is mapped into the Redirecting reason in the Call Diversion Information parameter is set as indicated in table 6.3.3-4

ISUP Parameter values CPG: Call Diversion Information Redirecting reason= Redirecting_Reason

SIP Parameter values 180: History-Info: <sip:any proper URI >; index=1, <sip:any proper URI;cause=CAUSE_value >; index=1.1 180 (CPG): History-Info not present




180 Ringing (CPG - Alerting)

� � 180 Ringing


ETSI

ETSI TS 101 572-2 V1.2.1 (2014-07)271


TSS reference IMS-SS/CDIV/ Selection criteria PICS 6.3.1/2 AND PICS 6.3.2/5 Test Purpose name Mapping of 200 OK hi-targeted-to-uri into ANM Redirection number Test Purpose Ensure that on receipt of 200 OK (INVITE) an ANM is sent. The last History-Info entry

containing a cause parameter is mapped into the Redirection number: • If CC of the hi-targeted-to-uri is equal the country code where the SUT is located:



ISUP Parameter values ANM: Redirection number Nature of address indicator Address signal Derived from the last History-Info entry

SIP Parameter values 200: History-Info: <sip:any proper URI>; index=1, <sip:any proper URI;cause=any value>; index=1.1 200 (ANM): History-Info not present




180 Ringing (CPG) � � 180 Ringing 200 OK INVITE (ANM) � � 200 OK INVITE ACK � � ACK



TSS reference IMS-SS/CDIV/ Selection criteria PICS 6.3.1/2 AND PICS 6.3.2/5 Test Purpose name Mapping of 200 escaped Privacy header into ANM Redirection number restriction Test Purpose Ensure that on receipt of 200 (INVITE), a 200 OK INVITE (ANM) with encapsulated ANM is

sent. The Redirection number restriction is set according the escaped Privacy header in the last History entry as indicated in table 6.3.3-1

ISUP Parameter values ANM: Redirection number restriction= PRES_restr SIP Parameter values 200 OK:

History-Info: <sip:any proper URI>; index=1, <sip:any proper URI;cause=any value?Privacy=Priv-value>; index=1.1 200 (ANM): History-Info not present






ETSI

ETSI TS 101 572-2 V1.2.1 (2014-07)272


TSS reference IMS-SS/CDIV/ Selection criteria PICS 6.3.1/2 AND PICS 6.3.2/5 Test Purpose name Mapping of 200 Privacy header into 200 OK INVITE (ANM) with encapsulated ANM

Redirection number restriction Test Purpose Ensure that on receipt of 200 OK (INVITE), a200 OK INVITE (ANM) with encapsulated

ANM is sent. The Redirection number restriction is set according the Privacy header as indicated in table 6.3.3-1

ISUP Parameter values ANM: Redirection number restriction= PRES_restr SIP Parameter values 200 OK:

Privacy=Priv-value History-Info: <sip:any proper URI>; index=1, <sip:any proper URI;cause=any value>; index=1.1 200 (ANM): History-Info not present







TSS reference IMS-SS/CDIV/ Selection criteria PICS 6.3.1/2 AND PICS 6.3.2/5 Test Purpose name Mapping of 200 OK hi-targeted-to-uri into 200 OK (INVITE) with encapsulated CON

Redirection number Test Purpose Ensure that on receipt of 200 OK (INVITE) a 200 OK (INVITE) with encapsulated CON is

sent. The History-Info entry containing a cause parameter is mapped into the Redirection number: • If CC of the hi-targeted-to-uri is equal the country code where the SUT is located:



ISUP Parameter values CON: Redirection number Nature of address indicator Address signal Derived from the last History-Info entry

SIP Parameter values 200 OK: History-Info: <sip:any proper URI>; index=1, <sip:any proper URI;cause=any value ; index=1.1 200 (CON): History-Info not present


INVITE (IAM) � � INVITE 200 OK INVITE (CON) � � 200 OK INVITE ACK � � ACK


ETSI

ETSI TS 101 572-2 V1.2.1 (2014-07)273


TSS reference IMS-SS/CDIV/ Selection criteria PICS 6.3.1/2 AND PICS 6.3.2/5 Test Purpose name Mapping of 200 escaped Privacy header into 200 OK (INVITE) with encapsulated CON

Redirection number restriction Test Purpose Ensure that on receipt of 200 (INVITE), a 200 OK (INVITE) with encapsulated CON is sent.

The Redirection number restriction is set according the escaped Privacy header in the last History entry as indicated in table 6.3.3-1

ISUP Parameter values CON: Redirection number restriction= PRES_restr SIP Parameter values 200 OK:

History-Info: <sip:any proper URI>; index=1, <sip:any proper URI;cause=any value?Privacy=Priv-value>; index=1.1 200 (CON): History-Info not present





TSS reference IMS-SS/CDIV/ Selection criteria PICS 6.3.1/2 AND PICS 6.3.2/5 Test Purpose name Mapping of 200 Privacy header into 200 OK (INVITE) with encapsulated CON Redirection

number restriction Test Purpose Ensure that on receipt of 200 OK (INVITE), a 200 OK (INVITE) with encapsulated CON is

sent. The Redirection number restriction is set according the Privacy header as indicated in table 6.3.3-1

ISUP Parameter values CON: Redirection number restriction= PRES_restr SIP Parameter values 200 OK:

Privacy=Priv-value History-Info: <sip:any proper URI>; index=1, <sip:any proper URI;cause=any value>; index=1.1 200 (CON): History-Info not present




ETSI

ETSI TS 101 572-2 V1.2.1 (2014-07)274


TSS reference IMS-SS/CDIV/ Selection criteria PICS 6.3.1/2 AND PICS 6.3.2/5 Test Purpose name Mapping of Redirecting number Address signals into History-Info header URI Test Purpose Ensure that on receipt of an INVITE with encapsulated IAM containing a Redirecting

number parameter, an Original called number parameter and a Redirection Information parameter, an INVITE request is sent and a History-Info header is present. The value of the second last hi-targeted-to-uri Value of Redirecting number is mapped from the Redirecting number Address Signals as indicated in table 6.3.3-6

ISUP Parameter values IAM: Redirecting number Nature of Address: NoA_value Address Signals <any appropriate value> Redirection Information Redirection counter=2 Original called number

SIP Parameter values INVITE: History-Info: <sip:any proper URI>; index=1, <sip:Value of Redirecting number;cause=any>; index=1.1 <sip: any proper URI;cause=any>; index=1.1.1 INVITE (IAM): History-Info not present



Table 6.3.3-6: Mapping of Redirecting number into second last Hist-entry

NoA_value Value of Redirecting number second last hi-targeted-to-uri

VA_01 national (significant) number Add '+' and the country code where the SUT is located to the Address Signal digits of the Redirecting number

VA_02 international number Add '+' to the Address Signal digits of the Redirecting number


TSS reference IMS-SS/CDIV/ Selection criteria PICS 6.3.1/2 AND PICS 6.3.2/5 Test Purpose name Mapping of Redirecting number Address presentation restricted into History-Info header

Privacy value Test Purpose Ensure that on receipt of an INVITE with encapsulated IAM containing a Redirecting, an

Original called number parameter number parameter and a Redirection Information parameter, an INVITE request is sent and a History-Info header is present. A Privacy header is escaped in the second last hi-targeted-to-uri and the PRIV_value is mapped from the Address presentation restricted indicator of the Redirecting number as indicated in table 6.2.5-7

ISUP Parameter values IAM: Redirecting number Address presentation restricted indicator: APRI_value Redirection Information Redirection counter=2 Original called number

SIP Parameter values INVITE: History-Info: <sip:any proper URI>; index=1, <sip: any proper URI;cause=any?Privacy=PRIV_value>; index=1.1 <sip: any proper URI;cause=any>; index=1.1.1 INVITE (IAM): History-Info not present



ETSI

ETSI TS 101 572-2 V1.2.1 (2014-07)275

Table 6.3.3-7: Mapping of Redirecting number APRI into Privacy header in the second last Hist-entry

APRI_value PRIV_value second last hi-targeted-to-uri

VA_01 presentation restricted history VA_02 presentation allowed Header absent or 'none'


TSS reference IMS-SS/CDIV/ Selection criteria PICS 6.3.1/2 AND PICS 6.3.2/5 Test Purpose name Mapping of Redirection Information Redirecting indicator Test Purpose Ensure that on receipt of an INVITE with encapsulated IAM containing a Redirecting

number, an Original called number parameter and a Redirection Information parameter, an INVITE request is sent and a History-Info header is present. A Privacy header is escaped in the second last hi-targeted-to-uri and the PRIV_value is mapped from the Redirecting indicator of the Redirection Information as indicated in table 6.2.5-21

ISUP Parameter values IAM: Redirection Information Redirection counter=2 Redirecting indicator=RDIND_value

SIP Parameter values INVITE: History-Info: <sip:any proper URI>; index=1, <sip: any proper URI;cause=any?Privacy=PRIV_value>; index=1.1 <sip: any proper URI;cause=any>; index=1.1.1 INVITE (IAM): History-Info not present



Table 6.3.3-8: Mapping of Redirecting indicator into Privacy header in the second last Hist-entry

RDIND_value PRIV_value second last hi-targeted-to-uri

VA_01 Call diverted, all redirection info presentation restricted history VA_02 Call diverted none


TSS reference IMS-SS/CDIV/ Selection criteria PICS 6.3.1/2 AND PICS 6.3.2/5 Test Purpose name Mapping of Redirection Information Redirection counter Test Purpose Ensure that on receipt of an INVITE with encapsulated IAM containing a Redirecting

number, an Original called number parameter and a Redirection Information parameter, an INVITE request is sent and a the hi-targeted-to-uri and the index parameter of the Redirection counter as indicated in table 6.3.3-9

ISUP Parameter values IAM: Redirection Information Redirection counter=RDCONT_value

SIP Parameter values INVITE: History-Info: HI-ENTRY_values INVITE (IAM): History-Info not present



ETSI

ETSI TS 101 572-2 V1.2.1 (2014-07)276

Table 6.3.3-9: Mapping of Redirection counter into index parameter of History-Info header

RDCONT_value HI-ENTRY_values VA_01 1 <sip:represents the Original called number>; index=1,

<sip: represents the Called party number;cause=any>; index=1.1 VA_02 2 <sip: represents the Original called number>; index=1,

<sip: represents the Redirecting number;cause=any>; index=1.1, <sip: represents the Called party number;cause=any>; index=1.1.1

VA_03 3 <sip: represents the Original called number>; index=1, <sip: represents any placeholder value;cause=any>; index=1.1, <sip: represents the Redirecting number;cause=404>; index=1.1.1, <sip: represents the Called party number;cause=any>; index=1.1.1.1

VA_04 4 <sip: represents the Original called number>; index=1, <sip: represents any placeholder value;cause=any>; index=1.1, <sip: represents any placeholder value;cause=404>; index=1.1.1, <sip: represents the Redirecting number;cause=404>; index=1.1.1.1, <sip: represents the Called party number;cause=any>; index=1.1.1.1.1

VA_05 5 <sip: represents the Original called number>; index=1, <sip: represents any placeholder value;cause=any>; index=1.1, <sip: represents any placeholder value;cause=404>; index=1.1.1, <sip: represents any placeholder value;cause=404>; index=1.1.1.1, <sip: represents the Redirecting number;cause=404>; index=1.1.1.1.1, <sip: represents the Called party number;cause=any>; index=1.1.1.1.1.1


TSS reference IMS-SS/CDIV/ Selection criteria PICS 6.3.1/2 AND PICS 6.3.2/5 Test Purpose name Mapping of Redirection Information Original redirection reason Test Purpose Ensure that on receipt of an INVITE with encapsulated IAM containing a Redirecting

number an Original called number and a Redirection Information parameter, an INVITE request is sent. The Original redirection reason indicator 'unknown' of the Redirection Information is mapped into the cause parameter '404' of the second hi-targeted-to-uri of the History-Info header in the sent INVITE as indicated in table 6.3.3-10

ISUP Parameter values IAM: Redirection Information Redirection counter=2 Original redirection reason=unknown

SIP Parameter values INVITE: History-Info: <sip:any proper URI>; index=1, <sip:any proper URI;cause='404'>; index=1.1, <sip: any proper URI;cause=any>; index=1.1.1 INVITE (IAM): History-Info not present




ETSI

ETSI TS 101 572-2 V1.2.1 (2014-07)277


TSS reference IMS-SS/CDIV/ Selection criteria PICS 6.3.1/2 AND PICS 6.3.2/5 Test Purpose name Mapping of Redirection Information Redirecting reason Test Purpose Ensure that on receipt of an INVITE with encapsulated IAM containing a Redirection

number an Original called number and a Redirection Information parameter, an INVITE request is sent. The Redirecting reason indicator REAS_value of the Redirection Information is mapped into the cause parameter Cause_value of the last hi-targeted-to-uri of the History-Info header in the sent INVITE as indicated in table 6.3.3-11

ISUP Parameter values IAM: Redirection Information Redirection counter=2 Redirecting reason =REAS_value

SIP Parameter values INVITE: History-Info: <sip:any proper URI>; index=1, <sip:any proper URI;cause=any>; index=1.1, <sip: any proper URI;cause=Cause_value>; index=1.1.1 INVITE (IAM): History-Info not present



Table 6.3.3-11: Mapping of Redirecting reason into Reason header in the last Hist-entry

REAS_value Cause_value Second last hi-targeted-to-uri

VA_01 unknown 404 VA_02 unconditional 302 VA_03 User Busy 486 VA_04 No reply 408 VA_05 Deflection during alerting 302 VA_06 Deflection immediate response 302 VA_07 Mobile subscriber not reachable 503


TSS reference IMS-SS/CDIV/ Selection criteria PICS 6.3.1/2 AND PICS 6.3.2/5 Test Purpose name Mapping of Called party number Address Signals Test Purpose Ensure that on receipt of an INVITE with encapsulated IAM containing a Redirecting

number parameter and a Redirection Information parameter, an INVITE request is sent and a History-Info header is present. The Called party number is mapped into the last hi-targeted-to-uri of the History-Info header as indicated in table 6.3.3-12

ISUP Parameter values IAM: Called party number Nature of Address: NoA_value Address Signals

SIP Parameter values INVITE: History-Info: <sip:any proper URI>; index=1, <sip:any proper URI;cause=any>; index=1.1, <sip:Value of Called party number;cause=any>; index=1.1.1 INVITE (IAM): History-Info not present



ETSI

ETSI TS 101 572-2 V1.2.1 (2014-07)278

Table 6.3.3-12: Mapping of Called party number into last Hist-entry

NoA_value Value of Called party number last hi-targeted-to-uri

VA_01 national (significant) number Add '+' and the country code where the SUT is located to the Address Signal digits of the Called party number

VA_02 international number Add '+' to the Address Signal digits of the Called party number


TSS reference IMS-SS/CDIV/ Selection criteria PICS 6.3.1/2 AND PICS 6.3.2/5 Test Purpose name Mapping of Original called number Address Signals Test Purpose Ensure that on receipt of an INVITE with encapsulated IAM containing an Original called

number parameter and a Redirection Information parameter, an INVITE request is sent and a History-Info header is present. The value of the first hi-targeted-to-uri Value of Original called number is mapped from the Original called number Address Signals as indicated in table 6.3.3-13

ISUP Parameter values IAM: Original called number Nature of Address: NoA_value Address Signals <Digits>

SIP Parameter values INVITE: History-Info: <sip:Value of Original called number>; index=1, <sip:any proper URI;cause=any>; index=1.1 INVITE (IAM): History-Info not present



Table 6.3.3-13: Mapping of Original called number into first Hist-entry

NoA_value Value of Original called number First hi-targeted-to-uri

VA_01 national (significant) number Add '+' and the country code where the SUT is located to the Address Signal digits of the Original called number

VA_02 international number Add '+' to the Address Signal digits of the Original called number


TSS reference IMS-SS/CDIV/ Selection criteria PICS 6.3.1/2 AND PICS 6.3.2/5 Test Purpose name Mapping of Original called number Address presentation restricted indicator Test Purpose Ensure that on receipt of an INVITE with encapsulated IAM containing an Original called

number parameter, an INVITE request is sent and a History-Info header is present. A Privacy header escaped in the first hi-targeted-to-uri and the PRIV_value is mapped from the Address presentation restricted indicator of the Original called number as indicated in table 6.3.3-14

ISUP Parameter values IAM: Original called number Address presentation restricted indicator: APRI_value Address Signals <any appropriate value>

SIP Parameter values INVITE: History-Info: <sip:any proper URI?Privacy=PRIV_value>; index=1, <sip:any proper URI;cause=any>; index=1.1 INVITE (IAM): History-Info not present



ETSI

ETSI TS 101 572-2 V1.2.1 (2014-07)279

Table 6.3.3-14: Mapping of Original called number APRI into Privacy header in the first Hist-entry

APRI_value PRIV_value first hi-targeted-to-uri

VA_01 presentation restricted history VA_02 presentation allowed none

TP number TP_403_041 Reference [1], clause 7.2.1 [2], clauses 7.5.4.3, table, 7.5.4.3.2

TSS reference IMS-SS/CDIV/ Selection criteria PICS 6.3.1/2 AND PICS 6.3.2/5 Test Purpose name Second latest History-Info header field entry mapped into Redirecting number Nature of

address indicator Test Purpose Ensure that on receipt of an INVITE request containing a History-Info header, an INVITE

with encapsulated IAM is sent and a Redirecting number an Original called number and a Redirection information parameter is present. The Nature of address indicator of the Redirecting number is mapped from the hi-targeted-to-uri in hi-entry before last hi-entry containing a cause-param URI parameter as indicated in table 6.3.3-15

ISUP Parameter values IAM: Redirecting number Nature of address indicator=NoA_value

SIP Parameter values INVITE: History-Info: <sip:any proper URI>; index=1, <sip:Second last entry URI;cause=any>; index=1.1, <sip:any proper URI;cause=any>; index=1.1.1 INVITE (IAM): History-Info not present




Table 6.3.3-15: Mapping of second last first Hist-entry into Redirecting number Nature of address indicator

Second last entry URI NoA_value VA_01 CC is equal to the country code of the country

where MGCF is located AND the next ISUP node is located in the same country

national (significant) number

VA_02 CC is not equal to the country code of the country where MGCF is located

international number

ETSI

ETSI TS 101 572-2 V1.2.1 (2014-07)280


TSS reference IMS-SS/CDIV/ Selection criteria PICS 6.3.1/2 AND PICS 6.3.2/5 Test Purpose name Second latest History-Info header field entry is mapped into Redirecting number Address

signal Test Purpose Ensure that on receipt of an INVITE request containing a History-Info header, an INVITE

with encapsulated IAM is sent and a Redirecting number an Original called number and a Redirection information parameter is present. The Address signal of the Redirecting number is mapped from the hi-targeted-to-uri in hi-entry before last hi-entry containing a cause-param URI parameter in the format +'CC+NDC+SN' as indicated in table 6.3.3-16

ISUP Parameter values IAM: Redirecting number Address signal derived from the second last Hist-entry

SIP Parameter values INVITE: History-Info: <sip:any proper URI>; index=1, <sip:Second last entry URI;cause=any>; index=1.1, <sip:any proper URI;cause=any>; index=1.1.1 INVITE (IAM): History-Info not present




Table 6.3.3-16: Mapping of second last first Hist-entry into Redirecting number Address signal

Second last entry URI NoA_value VA_01 CC is equal to the country code of the country


'+CC' is removed from the userpart digit string used in the Redirecting number Address signal


'+' is removed from the userpart digit string used in the Redirecting number Address signal


TSS reference IMS-SS/CDIV/ Selection criteria PICS 6.3.1/2 AND PICS 6.3.2/5 Test Purpose name Second latest History-Info header escaped Privacy header is mapped into Redirecting

number Address presentation restricted indicator Test Purpose Ensure that on receipt of an INVITE request containing a History-Info header, an INVITE

with encapsulated IAM is sent and a Redirecting number an Original called number and a Redirection information parameter is present. The Address presentation restricted indicator of the Redirecting number is mapped from the escaped Privacy header of the second latest History-Info header field entry containing a cause parameter as indicated in table 6.3.3-17

ISUP Parameter values IAM: Redirecting number Address presentation restricted indicator=APRI_value

SIP Parameter values INVITE: History-Info: <sip:any proper URI>; index=1, <sip:any proper URI;cause=any?Privacy=PRIV_value>; index=1.1, <sip:any proper URI;cause=any>; index=1.1.1 INVITE (IAM): History-Info not present




ETSI

ETSI TS 101 572-2 V1.2.1 (2014-07)281


TSS reference IMS-SS/CDIV/ Selection criteria PICS 6.3.1/2 AND PICS 6.3.2/5 Test Purpose name Privacy header is mapped into Redirecting number Address presentation restricted

indicator Test Purpose Ensure that on receipt of an INVITE request containing a History-Info header, an INVITE

with encapsulated IAM is sent and a Redirecting number an Original called number and a Redirection information parameter is present. The Address presentation restricted indicator of the Redirecting number is mapped from the Privacy header of the received INVITE request as indicated in table 6.3.3-17.

ISUP Parameter values IAM: Redirecting number Address presentation restricted indicator=APRI_value

SIP Parameter values INVITE: Privacy: PRIV_value History-Info: <sip:any proper URI>; index=1, <sip:any proper URI;cause=any>; index=1.1 INVITE (IAM): History-Info not present




Table 6.3.3-17: Mapping of Privacy header into Redirecting number Address presentation restricted indicator

PRIV_value APRI_value VA_01 history presentation restricted VA_02 session presentation restricted VA_03 header presentation restricted VA_04 none presentation allowed VA_05 Header absent presentation allowed


TSS reference IMS-SS/CDIV/ Selection criteria PICS 6.3.1/2 AND PICS 6.3.2/5 Test Purpose name Escaped Privacy header is mapped into Redirection information Redirecting indicator Test Purpose Ensure that on receipt of an INVITE request containing a History-Info header, an INVITE

with encapsulated IAM is sent and a Redirecting number an Original called number and a Redirection information parameter is present. The Redirecting indicator of the Redirection information is mapped from the escaped Privacy header of the second last History-Info header field entry and last History-Info header field in the received INVITE request as indicated in table 6.3.3-18

ISUP Parameter values IAM: Redirection information Redirecting indicator=RDIND_value

SIP Parameter values INVITE: History-Info: <sip:any proper URI>; index=1, <sip:any proper URI;cause=any?Privacy=PRIV_value>; index=1.1, <sip:any proper URI;cause=any?Privacy=PRIV_value>; index=1.1.1 INVITE (IAM): History-Info not present




ETSI

ETSI TS 101 572-2 V1.2.1 (2014-07)282


TSS reference IMS-SS/CDIV/ Selection criteria PICS 6.3.1/2 AND PICS 6.3.2/5 Test Purpose name Privacy header is mapped into Redirection information Redirecting indicator Test Purpose Ensure that on receipt of an INVITE request containing a History-Info header, an INVITE

with encapsulated IAM is sent and a Redirecting number an Original called number and a Redirection information parameter is present. The Redirecting indicator of the Redirection information is mapped from the Privacy header in the received INVITE request as indicated in table 6.3.3-18

ISUP Parameter values IAM: Redirection information Redirecting indicator=RDIND_value

SIP Parameter values INVITE: Privacy: PRIV_value History-Info: <sip:any proper URI>; index=1, <sip:any proper URI;cause=any>; index=1.1, <sip:any proper URI;cause=any>; index=1.1.1 INVITE (IAM): History-Info not present




Table 6.3.3-18: Mapping of Privacy header into Redirecting indicator

PRIV_value RDIND_value VA_01 history Call diverted, all redirection info presentation restricted VA_02 session Call diverted, all redirection info presentation restricted VA_03 header Call diverted, all redirection info presentation restricted VA_04 none Call diverted VA_05 Privacy header field absent Call diverted


TSS reference IMS-SS/CDIV/ Selection criteria PICS 6.3.1/2 AND PICS 6.3.2/5 Test Purpose name 'cause' parameter is mapped into Redirection information Redirecting reason Test Purpose Ensure that on receipt of an INVITE request containing a History-Info header, an INVITE

with encapsulated IAM is sent and a Redirecting number an Original called number and a Redirection information parameter is present. The Redirecting reason of the Redirection information is mapped from the cause parameter of the latest History-Info header field entry containing a cause parameter in the received INVITE request as indicated in table 6.3.3-19

ISUP Parameter values IAM: Redirection information Original redirection reason=unknown/not available Redirecting reason=REAS_value

SIP Parameter values INVITE: History-Info: <sip:any proper URI>; index=1, <sip:any proper URI;cause=any>; index=1.1, <sip:any proper URI; cause=Cause_value>; index=1.1.1 INVITE (IAM): History-Info not present




ETSI

ETSI TS 101 572-2 V1.2.1 (2014-07)283

Table 6.3.3-19: Mapping of cause parameter in the last Hist-entry into Redirecting reason

Cause_value Last hi-targeted-to-uri

REAS_value

VA_01 404 Unknown/not available VA_02 302 Unconditional VA_03 486 User busy VA_04 408 No reply VA_05 480 Deflection immediate response VA_06 487 Deflection during alerting VA_07 503 Mobile subscriber not reachable


TSS reference IMS-SS/CDIV/ Selection criteria PICS 6.3.1/2 AND PICS 6.3.2/5 Test Purpose name Hi-index is mapped into Redirection information Redirection counter Test Purpose Ensure that on receipt of an INVITE request containing a History-Info header, an INVITE

with encapsulated IAM is sent and a Redirecting number an Original called number and a Redirection information parameter is present. The Redirection counter of the Redirection information is mapped from the hi-index of the last History-Info header field entry in the received INVITE request as indicated in table 6.3.3-20. The number of dots in the hi-index value is equal to the value of the Redirection counter

ISUP Parameter values IAM: Redirection information Redirection counter=RDCONT_value

SIP Parameter values INVITE: History-Info: ENTRY_values INVITE (IAM): History-Info not present




Table 6.3.3-20: Mapping of Redirection counter into index parameters of History-Info header

ENTRY_values RDCONT_value VA_01 <sip:represents the Original called number>; index=1,

<sip:represents the Called party number;cause=any>; index=1.1 1

VA_02 <sip:represents the Original called number>; index=1, <sip:represents the Redirecting number;cause=any>; index=1.1, <sip:represents the Called party number;cause=any>; index=1.1.1

2

VA_03 <sip:represents the Original called number>; index=1, <sip:any proper URI;cause=any>; index=1.1, <sip:represents the Redirecting number;cause=any>; index=1.1.1, <sip:represents the Called party number;cause=any>; index=1.1.1.1

3

VA_04 <sip:represents the Original called number>; index=1, <sip:any proper URI;cause=any>; index=1.1, <sip:any proper URI;cause=any>; index=1.1.1, <sip:represents the Redirecting number;cause=any>; index=1.1.1.1, <sip:represents the Called party number;cause=any>; index=1.1.1.1.1

4

VA_05 <sip:represents the Original called number>; index=1, <sip:any proper URI;cause=any>; index=1.1, <sip:any proper URI;cause=any>; index=1.1.1, <sip:any proper URI;cause=any>; index=1.1.1.1, <sip:represents the Redirecting number;cause=any>; index=1.1.1.1.1, <sip:represents the Called party number;cause=any>; index=1.1.1.1.1.1

5

ETSI

ETSI TS 101 572-2 V1.2.1 (2014-07)284


TSS reference IMS-SS/CDIV/ Selection criteria PICS 6.3.1/2 AND PICS 6.3.2/5 Test Purpose name First History-Info header field entry is mapped into Original called number Nature of

address indicator Test Purpose Ensure that on receipt of an INVITE request containing a History-Info header, an INVITE

with encapsulated IAM is sent and a Redirecting number an Original called number and a Redirection information parameter is present. The Nature of address indicator of the Original called is mapped from the first History-Info header field entry in the format +'CC+NDC+SN' as indicated in table 6.3.3-21

ISUP Parameter values IAM: Original called number Numbering Plan Indicator=ISDN (Telephony) numbering plan (Recommendation E.164 [i.1]) Nature of address indicator=NoA_value

SIP Parameter values INVITE: History-Info: <sip:First entry URI>; index=1, <sip:any proper URI;cause=any>; index=1.1 INVITE (IAM): History-Info not present




Table 6.3.3-21: Mapping of first Hist-entry into Original called number Nature of address indicator

First entry URI NoA_value VA_01 CC is equal to the country code of the country


national (significant) number


international number


TSS reference IMS-SS/CDIV/ Selection criteria PICS 6.3.1/2 AND PICS 6.3.2/5 Test Purpose name First History-Info header field entry is mapped into Original called Address signal Test Purpose Ensure that on receipt of an INVITE request containing a History-Info header, an INVITE

with encapsulated IAM is sent and a Redirecting number an Original called number and a Redirection information parameter is present. The Address signal of the Original called number is mapped from the first History-Info header field entry in the format +'CC+NDC+SN' as indicated in table 6.3.3-22

ISUP Parameter values IAM: Original called Numbering Plan Indicator=ISDN (Telephony) numbering plan (Recommendation E.164 [i.1]) Address signal derived from the first Hist-entry

SIP Parameter values INVITE: History-Info: <sip:First entry URI>; index=1, <sip:any proper URI;cause=any>; index=1.1 INVITE (IAM): History-Info not present




ETSI

ETSI TS 101 572-2 V1.2.1 (2014-07)285

Table 6.3.3-22: Mapping of first Hist-entry into Original called number Address signal

First entry URI NoA_value VA_01 CC is equal to the country code of the country


'+CC' is removed from the userpart digit string used in the Original called number Address signal


'+' is removed from the userpart digit string used in the Original called number Address signal


TSS reference IMS-SS/CDIV/ Selection criteria PICS 6.3.1/2 AND PICS 6.3.2/5 Test Purpose name First History-Info header field entry escaped Privacy header is mapped into Original called

number Address presentation restricted indicator Test Purpose Ensure that on receipt of an INVITE request containing a History-Info header, an INVITE

with encapsulated IAM is sent and a Redirecting number an Original called number and a Redirection information parameter is present. The Address presentation restricted indicator of the Original called number is mapped from the escaped Privacy header of the first History-Info header field entry as indicated in table 6.3.3-23

ISUP Parameter values IAM: Original called Address presentation restricted indicator=APRI_value

SIP Parameter values INVITE: History-Info: <sip:First entry URI?Privacy=PRIV_value>; index=1, <sip:any proper URI;cause=any>; index=1.1 INVITE (IAM): History-Info not present





TSS reference IMS-SS/CDIV/ Selection criteria PICS 6.3.1/2 AND PICS 6.3.2/5 Test Purpose name Privacy header is mapped into Original called number Address presentation restricted

indicator Test Purpose Ensure that on receipt of an INVITE request containing a History-Info header, an INVITE

with encapsulated IAM is sent and a Redirecting number an Original called number and a Redirection information parameter is present. The Address presentation restricted indicator of the Original called number is mapped from the Privacy header of the received INVITE request as indicated in table 6.3.3-23

ISUP Parameter values IAM: Original called Address presentation restricted indicator=APRI_value

SIP Parameter values INVITE: Privacy: PRIV_value History-Info: <sip:First entry URI>; index=1, <sip:any proper URI;cause=any>; index=1.1 INVITE (IAM): History-Info not present




ETSI

ETSI TS 101 572-2 V1.2.1 (2014-07)286

Table 6.3.3-23: Mapping of Privacy header into Redirecting number Address presentation restricted indicator

PRIV_value APRI_value VA_01 history presentation restricted VA_02 session presentation restricted VA_03 header presentation restricted VA_04 none presentation allowed VA_05 Header absent presentation allowed


TSS reference IMS-SS/CDIV/ Selection criteria PICS 6.3.1/2 AND PICS 6.3.2/5 Test Purpose name Mapping of a 183 Session Progress with encapsulated ACM Redirection number into 181

(Being forwarded) History-Info header Test Purpose Ensure that on receipt of a 183 Session Progress with encapsulated ACM a Redirection

number and the Call diversion parameter is present as an indication a call diversion occurred, a 181 (Being forwarded) is sent. The Redirection number is mapped into the hi-targeted-to-uri in a History-Info header containing one hi-entry in the sent 181 as indicated in table 6.3.3-24

ISUP Parameter values ACM: Backward call indicator Called party statue='no indication' Generic notification=call is diverting Call diversion information Redirection number Nature of address indicator=NOA_value Address signal Digits

SIP Parameter values 181: History-Info: sip: LAST_HIST_URI;cause=any>; index=1 183 (ACM): History-Info not present


INVITE � � INVITE (IAM) 181 Being forwarded � � 183 Session Progress

(ACM - no indication) Apply post test routine

Table 6.3.3-24: Mapping Redirection number into History-Info header

NOA_value History-Info header: LAST_HIST_URI VA_01 national (significant) number Add '+' and CC (of the country where the MGCF is

located) to Redirection number Address Signals then map to user portion of the last hi-targeted-to-uri in the format '+ CC NDC SN'.

VA_01 international number Map complete Redirection number Address Signals and '+' to user portion of the last hi-targeted-to-uri in the format '+ CC NDC SN'

ETSI

ETSI TS 101 572-2 V1.2.1 (2014-07)287


TSS reference IMS-SS/CDIV/ Selection criteria PICS 6.3.1/2 AND PICS 6.3.2/5 Test Purpose name Mapping of a 183 Session Progress with encapsulated ACM Redirecting reason into 181

(Being forwarded) History-Info header cause parameter Test Purpose Ensure that on receipt of a 183 Session Progress with encapsulated ACM a Redirection

number and the Call diversion parameter is present as an indication a call diversion occurred, a 181 (Being forwarded) is sent. The Call diversion information Redirecting reason is mapped into the cause parameter of the hi-targeted-to-uri in a History-Info header in the sent 181 as indicated in table 6.3.3-25

ISUP Parameter values ACM: Backward call indicator Called party statue='no indication' Generic notification=call is diverting Redirection number Call diversion information Redirecting reason =REAS_value

SIP Parameter values 181: History-Info: sip: LAST_HIST_URI;cause=CAUSE _value>; index=1 183 (ACM): History-Info not present




Table 6.3.3-25: Mapping of Redirecting reason into cause parameter

CAUSE Redirecting_Reason REAS_value

Cause parameter, CAUSE_value

VA_01 unknown 404 VA_02 unconditional 302 VA_03 User Busy 486 VA_04 No reply 408 VA_05 Deflection during alerting 487 VA_06 Deflection immediate response 480 VA_07 Mobile subscriber not reachable 503


TSS reference IMS-SS/CDIV/ Selection criteria PICS 6.3.1/2 AND PICS 6.3.2/5 Test Purpose name Mapping of a 183 Session Progress with encapsulated ACM Notification subscription

options no 181 (Being forwarded) is sent Test Purpose Ensure that on receipt of a 183 Session Progress with encapsulated ACM a Redirection

number and the Call diversion parameter is present as an indication a call diversion occurred, if the Call diversion information Notification subscription options is set to presentation not allowed no provisional response is sent

ISUP Parameter values ACM: Generic notification=call is diverting Redirection number Call diversion information Notification subscription options=presentation not allowed




ETSI

ETSI TS 101 572-2 V1.2.1 (2014-07)288


TSS reference IMS-SS/CDIV/ Selection criteria PICS 6.3.1/2 AND PICS 6.3.2/5 Test Purpose name Mapping of a 183 Session Progress with encapsulated ACM Notification subscription

options into 181 (Being forwarded) escaped Privacy header Test Purpose Ensure that on receipt of an a 183 Session Progress with encapsulated ACM a Redirection

number and the Call diversion parameter is present as an indication a call diversion occurred, a 181 (Being forwarded) is sent. The escaped Privacy header of the last hi-targeted-to-uri in a History-Info header in the sent 181 is set to 'history'. When a 200 OK INVITE containing an encapsulated ANM message is received, a 200 OK INVITE is sent and a History-Info header is present, an escaped Privacy header is present the value is set as indicated in table 6.3.3-26

ISUP Parameter values ACM: Generic notification=call is diverting Redirection number Call diversion information Notification subscription options=NSO_value

SIP Parameter values 181: History-Info: sip: LAST_HIST_URI;cause=any?Privacy=history>; index=1 181 (ACM): History-Info not present 200 OK History-Info: sip: LAST_HIST_URI;cause=any?Privacy=PRIV_value>; index=1



(ACM - no indication) 180 Ringing � � 180 Ringing (CPG – Alerting) 200 OK � � 200 OK (ANM) ACK � � ACK


Table 6.3.3-26: Mapping of Notification subscription options into Privacy header

CAUSE NSO_value PRIV_value VA_01 Unknown history VA_02 presentation allowed with redirection number Header not present or 'none' VA_03 presentation allowed without redirection number history

ETSI

ETSI TS 101 572-2 V1.2.1 (2014-07)289


TSS reference IMS-SS/CDIV/ Selection criteria PICS 6.3.1/2 AND PICS 6.3.2/5 Test Purpose name Mapping of a 183 Session Progress with encapsulated CPG Redirection number into 181

(Being forwarded) History-Info header Test Purpose Ensure that on receipt of a 183 Session Progress with encapsulated CPG the Event

indicator is set to 'Progress' a Redirection number and the Call diversion parameter is present as an indication a call diversion occurred, a 181 (Being forwarded) is sent. The Redirection number is mapped into the hi-targeted-to-uri in a History-Info header in the sent 181 as indicated in table 6.3.3-24

ISUP Parameter values CPG: Event=Progress Generic notification=call is diverting Call diversion information Redirection number Nature of address indicator=NOA_value Address signal Digits

SIP Parameter values 181: History-Info: <sip:LAST_HIST_URI;cause=any>; index=1 181 (CPG): History-Info not present


INVITE � � INVITE (IAM) 180 Ringing � � 180 Ringing (ACM) 181 Being forwarded � � 183 Session Progress

(CPG - call is diverting) Apply post test routine


TSS reference IMS-SS/CDIV/ Selection criteria PICS 6.3.1/2 AND PICS 6.3.2/5 Test Purpose name Mapping of a 183 Session Progress with encapsulated CPG Redirecting reason into 181

(Being forwarded) History-Info header cause parameter Test Purpose Ensure that on receipt of a 183 Session Progress with encapsulated CPG the Event

indicator is set to 'Progress' a Redirection number and the Call diversion parameter is present as an indication a call diversion occurred, a 181 (Being forwarded) is sent. The Call diversion information Redirecting reason is mapped into the cause parameter of the hi-targeted-to-uri in a History-Info header in the sent 181 as indicated in table 6.3.3-25

ISUP Parameter values CPG: Event=Progress Generic notification=call is diverting Redirection number Call diversion information Redirecting reason =REAS_value

SIP Parameter values 181: History-Info: <sip:derived from Redirection number in ACM;cause=CAUSE _value>; index=1 181 (CPG): History-Info not present




ETSI

ETSI TS 101 572-2 V1.2.1 (2014-07)290


TSS reference IMS-SS/CDIV/ Selection criteria PICS 6.3.1/2 AND PICS 6.3.2/5 Test Purpose name Mapping of a 183 Session Progress with encapsulated CPG Notification subscription

option presentation not allowed no 181 (Being forwarded) is sent Test Purpose Ensure that on receipt of a 181 Being forwarded with encapsulated CPG the Event

indicator is set to 'Progress' a Redirection number and the Call diversion parameter is present as an indication a call diversion occurred, if the Call diversion information Notification subscription options is set to presentation not allowed no 181 (Being forwarded) is sent

ISUP Parameter values CPG: Event=Progress Generic notification=call is diverting Redirection number Call diversion information Notification subscription options=presentation not allowed


INVITE � � INVITE (IAM) 180 Ringing � � 180 Ringing (ACM) � 183 Session Progress



TSS reference IMS-SS/CDIV/ Selection criteria PICS 6.3.1/2 AND PICS 6.3.2/5 Test Purpose name Mapping of a 183 Session Progress with encapsulated CPG Notification subscription

options into 181 (Being forwarded) escaped Privacy header Test Purpose Ensure that on receipt of a 183 Session Progress with encapsulated CPG the Event

indicator is set to 'Progress' a Redirection number and the Call diversion parameter is present as an indication a call diversion occurred, a 181 (Being forwarded) is sent. The escaped Privacy header of the hi-targeted-to-uri in a History-Info header in the sent 181 is set to 'history'. When a 200 OK INVITE containing an encapsulated ANM message is received, a 200 OK INVITE is sent and a History-Info header is present, an escaped Privacy header is present the value is set as indicated in table 6.3.3-26

ISUP Parameter values CPG: Event=Progress Generic notification=call is diverting Redirection number Call diversion information Notification subscription options=NSO_value

SIP Parameter values 181: History-Info: <sip:any proper URI;cause=any?Privacy=history>; index=1 181 (CPG): History-Info not present 200 OK History-Info: sip: LAST_HIST_URI;cause=any?Privacy=PRIV_value>; index=1



(CPG - call is diverting) 180 Ringing � � 180 Ringing (CPG – Alerting) 200 OK � � 200 OK (ANM) ACK � � ACK


ETSI

ETSI TS 101 572-2 V1.2.1 (2014-07)291


TSS reference IMS-SS/CDIV/ Selection criteria PICS 6.3.1/2 AND PICS 6.3.2/5 Test Purpose name Mapping of a 180 Ringing with encapsulated CPG Alerting Redirection number into 180

(Ringing) History-Info header URI parameter Test Purpose Ensure that on receipt of a 180 Ringing with encapsulated CPG the Event indicator is set

to 'Alerting' a Redirection number is present, a 180 (Ringing) is sent. The Redirection number Address signal digits are mapped into the hi-targeted-to-uri in a History-Info header in the sent 180 (Ringing) as indicated in table 6.3.3-24.

ISUP Parameter values ACM: Call diversion information Redirection number CPG: Event indicator=Alerting Call diversion information Redirection number Nature of address indicator=NOA_value Address signal Digits

SIP Parameter values 180: History-Info: <sip:derived from Redirection number in CPG;cause=Cause_value>; index=1 180 (ACM): History-Info not present



(ACM) 180 Ringing � � 180 Ringing


TP number TP_403_061A Reference [1], clause 7.2.1 [2], clauses 7.5.4.3, table, 7.5.4.3.10

TSS reference IMS-SS/CDIV/ Selection criteria PICS 6.3.1/2 AND PICS 6.3.2/5 Test Purpose name Mapping of a 180 with encapsulated CPG Alerting Redirection number into 180 (Ringing)

History-Info header Redirecting reason is mapped into the cause parameter Test Purpose Ensure that on receipt of a 180 (Ringing) with encapsulated CPG the Event indicator is set

to 'Alerting' a Redirection number is present, a 180 (Ringing) is sent. The cause parameter value is mapped from the received Redirecting reason as indicated in table 6.3.3-25.

ISUP Parameter values ACM: Call diversion information Redirection number CPG: Event indicator=Alerting Redirection number Call diversion information Redirecting reason =REAS_value

SIP Parameter values 180: History-Info: <sip:any proper URI;cause=CAUSE _value>; index=1 180 (ACM): History-Info not present





ETSI

ETSI TS 101 572-2 V1.2.1 (2014-07)292

TP number TP_403_061B Reference [1], clause 7.2.1 [2], clauses 7.5.4.3, table, 7.5.4.3.10

TSS reference IMS-SS/CDIV/ Selection criteria PICS 6.3.1/2 AND PICS 6.3.2/5 Test Purpose name Mapping of a 180 with encapsulated CPG Alerting Notification subscription option the 180

(Ringing) containing a History-Info header is sent Test Purpose Ensure that on receipt of a180 Ringing with encapsulated CPG the Event indicator is set to

'Alerting' a Redirection number is present, a 180 (Ringing) is sent. The Privacy value is set to 'history'. When a 200 OK INVITE containing an encapsulated ANM message is received, a 200 OK INVITE is sent and a History-Info header is present, an escaped Privacy header is present as indicated in table 6.3.3-26

ISUP Parameter values ACM: Call diversion information Redirection number CPG: Event indicator=Alerting Redirection number Call diversion information Notification subscription options=NSO_value

SIP Parameter values 180: History-Info: <sip:any proper URI;cause=any?Privacy=history>; index=1 180 (ACM): History-Info not present 200 OK History-Info: sip: LAST_HIST_URI;cause=any?Privacy=PRIV_value>; index=1




(CPG - call is diverting) 200 OK � � 200 OK (ANM) ACK � � ACK


ETSI

ETSI TS 101 572-2 V1.2.1 (2014-07)293

TP number TP_403_061C Reference [1], clause 7.2.1 [2], clauses 7.5.4.3, table, 7.5.4.3.10

TSS reference IMS-SS/CDIV/ Selection criteria PICS 6.3.1/2 AND PICS 6.3.2/5 Test Purpose name Mapping of a 180 Ringing with an encapsulated CPG Alerting without Call Diversion

Information parameters the 180 (Ringing) containing a History-Info header is sent, cause parameter

Test Purpose Ensure that on receipt of a 180 Ringing with encapsulated CPG the Event indicator is set to 'Alerting' no Call diversion Information parameters are present, a 180 (Ringing) is sent. The cause parameter value is derived from the Redirection reason indicator of a previous received Call diversion information parameter as indicated in table 6.3.3-25.

ISUP Parameter values ACM: Redirection number Call diversion information Call diversion information Redirecting reason=REAS_value Redirection number CPG: Event indicator=Alerting

SIP Parameter values 181: History-Info: <sip:any proper URI;cause=any?Privacy=history>; index=1 180 (ACM): History-Info not present 180: History-Info: <sip: any proper URI;cause=CAUSE _value?Privacy=history>; index=1




(CPG - Alerting) Apply post test routine

ETSI

ETSI TS 101 572-2 V1.2.1 (2014-07)294

TP number TP_403_061D Reference [1], clause 7.2.1 [2], clauses 7.5.4.3, table, 7.5.4.3.10


Information parameters the 180 (Ringing) containing a History-Info header is sent, Privacy value

Test Purpose Ensure that on receipt of a 180 Ringing with encapsulated CPG the Event indicator is set to 'Alerting' no Call diversion Information parameters are present, a 180 (Ringing) is sent. The Privacy value is set to 'history'. On receipt of a 200 OK INVITE with an encapsulated ISUP ANM message is received, a 200 OK INVITE is sent and a History-Info header is present an escaped Privacy header is presentas indicated in table 6.3.3-26.

ISUP Parameter values ACM: Call diversion information Redirection number Call diversion information Notification subscription options=NSO_value CPG: Event indicator=Alerting

SIP Parameter values 181: History-Info: <sip:any proper URI;cause=any?Privacy=history>; index=1 180 (ACM): History-Info not present 200 OK History-Info: sip: LAST_HIST_URI;cause=any?Privacy=PRIV_value>; index=1



(ACM) 180 Ringing � � 180 Ringing (CPG - Alerting) 200 OK � � 200 OK (ANM) ACK � � ACK


TP number TP_403_061E Reference [1], clause 7.2.1 [2], clauses 7.5.4.3, table, 7.5.4.3.10


Information parameters the 180 (Ringing) a History-Info header is not present Test Purpose 183 Session Progress with encapsulated ACM Call diversion Information parameters are

present the Notification subscription options is set to 'presentation not allowed'. Ensure that on receipt of a 180 Ringing with encapsulated CPG the Event indicator is set to 'Alerting' no Call diversion Information parameters are present, a 180 (Ringing) is sent. A History-Info header is not present.

ISUP Parameter values ACM: Redirection number Call diversion information Notification subscription options=presentation not allowed CPG: Event indicator=Alerting

SIP Parameter values 180: History-Info header not present



(ACM) 180 Ringing � � 180 Ringing (CPG - Alerting)


ETSI

ETSI TS 101 572-2 V1.2.1 (2014-07)295


TSS reference IMS-SS/CDIV/ Selection criteria PICS 6.3.1/2 AND PICS 6.3.2/5 Test Purpose name Mapping of a 181 Being forwarded with encapsulated CPG Alerting Redirection Number

Restriction into 180 (Ringing) Privacy header Test Purpose Ensure that on receipt of a 181 Being forwarded with encapsulated CPG the Event indicator is

set to 'Alerting' a Redirection Number Restriction parameter is present, a 180 (Ringing) is sent. The Redirection Number Restriction parameter value is mapped into the Privacy header in the sent 180 as indicated in table 6.3.3-27

ISUP Parameter values

ACM: Backward call indicator Called party status=no indication Generic notification=call is diverting Call diversion information Notification subscription options=NSO_value Redirection number CPG: Event indicator=Alerting Redirection Number Restriction=PRES_restr

SIP Parameter values 180: History-Info: <sip:any proper URI;cause=any?Privacy=PRIV_value>; index=1




(CPG - Alerting) Apply post test routine

Table 6.3.3-27: Mapping of Redirection Number Restriction parameter into Privacy header

CAUSE Redirection Number Restriction PRES_restr

Privacy PRIV_value

VA_01 Presentation allowed AND previous received Notification subscription option NSO_value was NOT "presentation not allowed" AND was NOT "presentation allowed without redirection number"

'none' OR Header not present

VA_02 Presentation restricted 'History' VA_03 Parameter absent

AND previous received Notification subscription option NSO_value was NOT "presentation not allowed" AND was NOT "presentation allowed without redirection number"

'none' OR Header not present

ETSI

ETSI TS 101 572-2 V1.2.1 (2014-07)296


TSS reference IMS-SS/CDIV/ Selection criteria PICS 6.3.1/2 AND PICS 6.3.2/5 Test Purpose name Mapping of 200 OK INVITE with encapsulated ANM Redirection Number Restriction into

200 OK INVITE Privacy header Test Purpose Ensure that on receipt of a 200 OK INVITE with encapsulated ANM a Redirection Number

Restriction parameter is present as an indication a call diversion occurred, a 200 OK INVITE is sent. The Redirection Number Restriction parameter value is mapped into the Privacy header in the sent 200 OK INVITE as indicated in table 6.3.3-27

ISUP Parameter values ACM: Generic notification=call is diverting Call diversion information Notification subscription options=NSO_value Redirection number ANM: Redirection Number Restriction=PRES_restr

SIP Parameter values 200 OK INVITE: History-Info: <sip:any proper URI;cause=any?Privacy=PRIV_value>; index=1 200 (ANM): History-Info not present



(ACM) 180 Ringing � � 180 Ringing (CPG) 200 OK INVITE � � 200 OK INVITE (ANM) ACK � � ACK


6.3.4 Conference call (CONF)


TSS reference PSTN-SS/CONF/ Selection criteria PICS 6.3.1/2 AND PICS 6.3.2/20 AND PICS 6.3.9/1 Test Purpose name 'isfocus' parameter and conference URI in Contact header in ACK received, a SUBSCRIBE

is sent Test Purpose Ensure that on receipt of an INVITE request and a Contact header field is present

containing the conference URI and the 'isfocus' parameter, a SUBSCRIBE request is sent after the ACK was received. The Request URI contains the value received in the Contact header in the ACK, the To header is set to the value sent in the 180 Ringing, the P-Asserted-Identity is set to the value of the P-Asserted-Identity sent in the 180 Ringing or the 200 OK INVITE the Privacy header is sent as in the 180 Ringing or 200 OK INVITE

ISUP Parameter values SIP Parameter values INVITE: Contact: <conference URI>; isfocus

SUBSCRIBE: Request URI derived from the Contact header To: <URI equal to the value in the 180> P-Asserted-Identity: < URI equal to the value in the 180 or 200>


INVITE � � INVITE (IAM) 100 Trying � 180 Ringing � � 180 Ringing (ACM) 200 OK (INVITE) � � 200 OK (INVITE) (ANM) ACK � SUBSCRIBE � 202 Accepted �


ETSI

ETSI TS 101 572-2 V1.2.1 (2014-07)297


TSS reference PSTN-SS/CONF/ Selection criteria PICS 6.3.1/2 AND PICS 6.3.2/20 AND PICS 6.3.9/1 Test Purpose name 'isfocus' parameter and conference URI in Contact header in 200 OK received, a

SUBSCRIBE is sent Test Purpose Ensure that on receipt of a 200 OK INVITE successful final response and a Contact header

field is present containing the conference URI and the 'isfocus' parameter, a SUBSCRIBE request is sent. The Request URI contains the value received in the Contact header in the 200 OK, the From header is set to the value sent in the initial INVITE request, the P-Asserted-Identity is set to the value of the P-Asserted-Identity sent in the initial INVITE request the Privacy header is sent as in the initial INVITE

ISUP Parameter values SIP Parameter values 200: Contact: <conference URI>; isfocus

SUBSCRIBE: From: <URI equal to the value in the INVITE> P-Asserted-Identity: < URI equal to the value in the INVITE>


INVITE (IAM) � � INVITE 100 Trying � � 100 Trying 180 Ringing (ACM) � � 180 Ringing 200 OK (INVITE) (ANM) � � 200 OK (INVITE) ACK � � ACK � SUBSCRIBE � 202 Accepted


ETSI

ETSI TS 101 572-2 V1.2.1 (2014-07)298


TSS reference PSTN-SS/CONF/ Selection criteria PICS 6.3.1/2 AND PICS 6.3.2/20 AND PICS 6.3.9/1 Test Purpose name Interworking of notification of 'Conference established' at the I-MGCF Test Purpose Ensure that on receipt of an initial INVITE request and the Contact header contains the

isfocus parameter, a SUBCRIBE request is sent. Ensure that on receipt of a NOTIFY request as a response to the SUBSCRIBE request and a XML conference-info instance is present, the 'conference-state' 'active' element is set to 'true' an ISUP CPG message is set and the Generic notification parameter is set to 'Conference established'


SIP Parameter values INVITE: Contact: <conference URI>; isfocus NOTIFY: Subscription-State: active Event: conference Content-Type: application/conference-info+xml <?xml version="1.0" conference-info conference-state active>true<


INVITE � � INVITE (IAM) 100 Trying � � 100 Trying 180 Ringing � � 180 Ringing (ACM) 200 OK (INVITE) � � 200 OK (INVITE) (ANM) ACK � � ACK SUBSCRIBE � 202 Accepted � NOTIFY � � INFO (CPG) 200 OK (NOTIFY) � 200 OK (INFO)


ETSI

ETSI TS 101 572-2 V1.2.1 (2014-07)299


TSS reference PSTN-SS/CONF/ Selection criteria PICS 6.3.1/2 AND PICS 6.3.2/20 AND PICS 6.3.9/1 Test Purpose name Interworking of notification of 'Conference established' at the O-MGCF Test Purpose Ensure that on receipt of an INVITE request after a session was established and the

Contact header contains the isfocus parameter, a SUBCRIBE request is sent. Ensure that on receipt of a NOTIFY request as a response to the SUBSCRIBE request and a XML conference-info instance is present, the 'active' sub element of the 'conference-state' element is set to 'true' an INFO with encapsulated ISUP CPG message is set and the Generic notification parameter is set to 'Conference established'. The INVITE request contains also a Replaces header to terminate the originally session by sending a BYE request


SIP Parameter values INVITE 1: CallID: xxx INVITE 2: CallID: yyy Contact: <conference URI>; isfocus Replaces: xxx; to-tag=<>;from-tag=<> NOTIFY: Subscription-State: active Event: conference Content-Type: application/conference-info+xml <?xml version="1.0" conference-info conference-state active>true< BYE: CallID: xxx

Comments Note that the INVITE received in the confirmed dialogue is originated by the conference focus. The originally dialogue have to terminated.

Message flows SIP-I MGCF SIP NNI INVITE (IAM) � � INVITE 1 100 Trying � � 100 Trying 180 Ringing (ACM) � � 180 Ringing 200 OK (INVITE) (ANM) � � 200 OK (INVITE) ACK � � ACK � INVITE 2 � 200 OK (INVITE) � ACK � SUBSCRIBE � 202 Accepted INFO (CPG) � � NOTIFY 200 OK INFO � � 200 OK (NOTIFY) � BYE � 200 OK (BYE)


ETSI

ETSI TS 101 572-2 V1.2.1 (2014-07)300


TSS reference PSTN-SS/CONF/ Selection criteria PICS 6.3.1/2 AND PICS 6.3.2/20 AND PICS 6.3.9/1 Test Purpose name Interworking of notification of 'other party added' at the I-MGCF Test Purpose An established conference is already indicated by receipt of an adequate NOTIFY request

at the I-MGCF. Ensure that on receipt of a NOTIFY request and the 'entity' attribute of the 'endpoint' element does not contain the ISUP address as received in the To header and the 'status' sub element of the 'endpoint' element is set to connected, an INFO with encapsulated ISUP CPG message is sent the Generic notification indicator is set to 'other party added'

ISUP Parameter values CPG: Generic notification other party added

SIP Parameter values NOTIFY: To: <SIP-I address> Subscription-State: active Event: conference Content-Type: application/conference-info+xml <?xml version="1.0" conference-info users user endpoint entity="<not URI of ISUP>" status>connected<


Session is established and joined in a conference NOTIFY � � INFO (CPG) 200 OK (NOTIFY) � � 200 OK (INFO)



TSS reference PSTN-SS/CONF/ Selection criteria PICS 6.3.1/2 AND PICS 6.3.2/20 AND PICS 6.3.9/1 Test Purpose name Interworking of notification of 'other party added' at the O-MGCF Test Purpose An established conference is already indicated by receipt of an adequate NOTIFY request

at the O-MGCF. Ensure that on receipt of a NOTIFY request and the 'entity' attribute of the 'endpoint' element does not contain the ISUP address as received in the To header and the 'status' sub element of the 'endpoint' element is set to connected, an INFO with encapsulated ISUP CPG message is sent the Generic notification indicator is set to 'other party added'

ISUP Parameter values CPG: Generic notification other party added



Session is established and joined in a conference INFO (CPG) � � NOTIFY 200 OK INFO � � 200 OK (NOTIFY)


ETSI

ETSI TS 101 572-2 V1.2.1 (2014-07)301


TSS reference PSTN-SS/CONF/ Selection criteria PICS 6.3.1/2 AND PICS 6.3.2/20 AND PICS 6.3.9/1 Test Purpose name Interworking of notification of 'isolated' at the I-MGCF Test Purpose An established conference is already indicated by receipt of an adequate NOTIFY request

at the I-MGCF. Ensure that on receipt of a NOTIFY request and the 'entity' attribute of the 'endpoint' element contains the ISUP address as received in the To header and the 'status' sub element of the 'endpoint' element is set to on-hold, an INFO with encapsulated ISUP CPG message is sent the Generic notification indicator is set to 'isolated'

ISUP Parameter values CPG: Generic notification Isolated

SIP Parameter values NOTIFY: To: <SIP-I address> Subscription-State: active Event: conference Content-Type: application/conference-info+xml <?xml version="1.0" conference-info users user endpoint entity="<URI of SIP-I>" status>on-hold<


Session is established and joined in a conference CASE A NOTIFY � � INFO (CPG) 200 OK (NOTIFY) � � 200 OK INFO CASE B NOTIFY � � INFO (CPG) 200 OK (NOTIFY) � � 200 OK INFO INVITE(sendonly) � � INVITE (sendonly) 200 OK (INVITE) � � 200 OK (INVITE) ACK � � ACK


ETSI

ETSI TS 101 572-2 V1.2.1 (2014-07)302


TSS reference PSTN-SS/CONF/ Selection criteria PICS 6.3.1/2 AND PICS 6.3.2/20 AND PICS 6.3.9/1 Test Purpose name Interworking of notification of 'isolated' at the O-MGCF Test Purpose An established conference is already indicated by receipt of an adequate NOTIFY request

at the O-MGCF. Ensure that on receipt of a NOTIFY request and the 'entity' attribute of the 'endpoint' element contains the ISUP address as received in the To header and the 'status' sub element of the 'endpoint' element is set to on-hold, an INFO with encapsulated ISUP CPG message is sent the Generic notification indicator is set to 'isolated'

ISUP Parameter values CPG: Generic notification Isolated

SIP Parameter values NOTIFY: To: <SIP-I address> Subscription-State: active Event: conference Content-Type: application/conference-info+xml <?xml version="1.0" conference-info users user endpoint entity="<URI of SIP-I>" status>on-hold<


Session is established and joined in a conference CASE A INFO (CPG) � � NOTIFY 200 OK (INFO) � � 200 OK (NOTIFY) CASE B INFO (CPG) � � NOTIFY 200 OK INFO � � 200 OK (NOTIFY) INVITE(sendonly) � � INVITE(sendonly) 200 OK (INVITE) � � 200 OK (INVITE) ACK � � ACK


ETSI

ETSI TS 101 572-2 V1.2.1 (2014-07)303


TSS reference PSTN-SS/CONF/ Selection criteria PICS 6.3.1/2 AND PICS 6.3.2/20 AND PICS 6.3.9/1 Test Purpose name Interworking of notification of 'other party isolated' at the I-MGCF Test Purpose An established conference is already indicated by receipt of an adequate NOTIFY request

at the I-MGCF. Ensure that on receipt of a NOTIFY request and the 'entity' attribute of the 'endpoint' element does not contain the ISUP address as received in the To header and the 'status' sub element of the 'endpoint' element is set to on-hold, an INFO with encapsulated ISUP CPG message is sent the Generic notification indicator is set to 'other party isolated'

ISUP Parameter values CPG: Generic notification other party isolated

SIP Parameter values NOTIFY: To: <SIP-I address> Subscription-State: active Event: conference Content-Type: application/conference-info+xml <?xml version="1.0" conference-info users user endpoint entity="<not URI of ISUP>" status>on-hold<


Session is established and joined in a conference NOTIFY � � INFO (CPG) 200 OK (NOTIFY) � � 200 OK INFO



TSS reference PSTN-SS/CONF/ Selection criteria PICS 6.3.1/2 AND PICS 6.3.2/20 AND PICS 6.3.9/1 Test Purpose name Interworking of notification of 'other party isolated' at the O-MGCF Test Purpose An established conference is already indicated by receipt of an adequate NOTIFY request

at the O-MGCF. Ensure that on receipt of a NOTIFY request and the 'entity' attribute of the 'endpoint' element does not contain the ISUP address as received in the To header and the 'status' sub element of the 'endpoint' element is set to on-hold, an INFO with encapsulated ISUP CPG message is sent the Generic notification indicator is set to 'other party isolated'

ISUP Parameter values CPG: Generic notification other party isolated

SIP Parameter values NOTIFY: To: <SIP-I address> Subscription-State: active Event: conference Content-Type: application/conference-info+xml <?xml version="1.0" conference-info users user endpoint entity="<not URI of ISUP>" status>on-hold<


Session is established and joined in a conference INFO (CPG) � � NOTIFY 200 OK INFO � � 200 OK (NOTIFY)


ETSI

ETSI TS 101 572-2 V1.2.1 (2014-07)304


TSS reference PSTN-SS/CONF/ Selection criteria PICS 6.3.1/2 AND PICS 6.3.2/20 AND PICS 6.3.9/1 Test Purpose name Interworking of notification of 'reattached' at the I-MGCF Test Purpose An established conference is already indicated by receipt of an adequate NOTIFY request

and isolated at the I-MGCF. Ensure that on receipt of a NOTIFY request and the 'entity' attribute of the 'endpoint' element contains the ISUP address as received in the To header and the 'status' sub element of the 'endpoint' element is set to connected, an INFO with encapsulated ISUP CPG message is sent the Generic notification indicator is set to 'reattached'

ISUP Parameter values CPG: Generic notification reattached

SIP Parameter values NOTIFY: To: <SIP-I address> Subscription-State: active Event: conference Content-Type: application/conference-info+xml <?xml version="1.0" conference-info users user endpoint entity="<URI of SIP-I>" status>connected<


Session is established joined in a conference and isolated CASE A NOTIFY � � INFO (CPG) 200 OK (NOTIFY) � � 200 OK (INFO) CASE B NOTIFY � � INFO (CPG) 200 OK (NOTIFY) � � 200 OK (INFO) INVITE(sendrecv) � � INVITE(sendrecv) 200 OK (INVITE) � � 200 OK (INVITE) ACK � � ACK


ETSI

ETSI TS 101 572-2 V1.2.1 (2014-07)305


TSS reference PSTN-SS/CONF/ Selection criteria PICS 6.3.1/2 AND PICS 6.3.2/20 AND PICS 6.3.9/1 Test Purpose name Interworking of notification of 'reattached' at the O-MGCF Test Purpose An established conference is already indicated by receipt of an adequate NOTIFY request

and isolated at the I-MGCF. Ensure that on receipt of a NOTIFY request and the 'entity' attribute of the 'endpoint' element contains the ISUP address as received in the To header and the 'status' sub element of the 'endpoint' element is set to connected, an INFO with encapsulated ISUP CPG message is sent the Generic notification indicator is set to 'reattached'

ISUP Parameter values CPG: Generic notification Reattached

SIP Parameter values NOTIFY: To: <SIP-I address> Subscription-State: active Event: conference Content-Type: application/conference-info+xml <?xml version="1.0" conference-info users user endpoint entity="<URI of SIP-I>" status>connected<


Session is established joined in a conference and isolated CASE A INFO (CPG) � � NOTIFY 200 OK (INFO) � � 200 OK (NOTIFY) CASE B INFO (CPG) � � NOTIFY 200 OK (INFO) � � 200 OK (NOTIFY) INVITE(sendrecv) � � INVITE(sendrecv) 200 OK (INVITE) � � 200 OK (INVITE) ACK � � ACK


ETSI

ETSI TS 101 572-2 V1.2.1 (2014-07)306


TSS reference PSTN-SS/CONF/ Selection criteria PICS 6.3.1/2 AND PICS 6.3.2/20 AND PICS 6.3.9/1 Test Purpose name Interworking of notification of 'other party reattached' at the I-MGCF Test Purpose An established conference is already indicated by receipt of an adequate NOTIFY request

and another party is isolated at the I-MGCF. Ensure that on receipt of a NOTIFY request and the 'entity' attribute of the 'endpoint' element does not contain the ISUP address as received in the To header and the 'status' sub element of the 'endpoint' element is set to connected, an INFO with encapsulated ISUP CPG message is sent the Generic notification indicator is set to 'other party reattached'

ISUP Parameter values CPG: Generic notification other party reattached



Session is established joined in a conference and another party was isolated NOTIFY � � INFO (CPG) 200 OK (NOTIFY) � � 200 OK (INFO)



TSS reference PSTN-SS/CONF/ Selection criteria PICS 6.3.1/2 AND PICS 6.3.2/20 AND PICS 6.3.9/1 Test Purpose name Interworking of notification of 'other party reattached' at the O-MGCF Test Purpose An established conference is already indicated by receipt of an adequate NOTIFY request

and another party is isolated at the O-MGCF. Ensure that on receipt of a NOTIFY request and the 'entity' attribute of the 'endpoint' element does not contain the ISUP address as received in the To header and the 'status' sub element of the 'endpoint' element is set to connected, an INFO with encapsulated ISUP CPG message is sent the Generic notification indicator is set to 'other party reattached'

ISUP Parameter values CPG: Generic notification other party reattached



Session is established joined in a conference and another party was isolated INFO (CPG) � � NOTIFY 200 OK (INFO) � 200 OK (NOTIFY)


ETSI

ETSI TS 101 572-2 V1.2.1 (2014-07)307


TSS reference PSTN-SS/CONF/ Selection criteria PICS 6.3.1/2 AND PICS 6.3.2/20 AND PICS 6.3.9/1 Test Purpose name Interworking of notification of 'other party disconnected' at the I-MGCF Test Purpose An established conference is already indicated by receipt of an adequate NOTIFY request

at the I-MGCF. Ensure that on receipt of a NOTIFY request and the 'entity' attribute of the 'endpoint' element does not the ISUP address as received in the To header and the 'status' sub element of the 'endpoint' element is set to dialled-out, an INFO with encapsulated ISUP CPG message is sent the Generic notification indicator is set to 'other party disconnected'

ISUP Parameter values CPG: Generic notification other party disconnected

SIP Parameter values NOTIFY: To: <SIP-I address> Subscription-State: active Event: conference Content-Type: application/conference-info+xml <?xml version="1.0" conference-info users user endpoint entity="<not URI of ISUP>" status>disconnected< joining-method>dialled-in< or joining-method>dialled-out<


Session is established and joined in a conference NOTIFY � � INFO (CPG) 200 OK (NOTIFY) � � 200 OK (NOTIFY)



TSS reference PSTN-SS/CONF/ Selection criteria PICS 6.3.1/2 AND PICS 6.3.2/20 AND PICS 6.3.9/1 Test Purpose name Interworking of notification of 'other party disconnected' at the O-MGCF Test Purpose An established conference is already indicated by receipt of an adequate NOTIFY request

at the O-MGCF. Ensure that on receipt of a NOTIFY request and the 'entity' attribute of the 'endpoint' element does not contain the ISUP address as received in the To header and the 'status' sub element of the 'endpoint' element is set to dialled-out, an INFO with encapsulated ISUP CPG message is sent the Generic notification indicator is set to 'other party disconnected'

ISUP Parameter values CPG: Generic notification other party disconnected

SIP Parameter values NOTIFY: To: <SIP-I address> Subscription-State: active Event: conference Content-Type: application/conference-info+xml <?xml version="1.0" conference-info users user endpoint entity="<not URI of ISUP>" status>disconnected< or joining-method>dialled-out<


Session is established and joined in a conference INFO (CPG) � � NOTIFY 200 OK (INFO) � � 200 OK (NOTIFY)


ETSI

ETSI TS 101 572-2 V1.2.1 (2014-07)308

6.3.5 Message Waiting Indication (MWI)

Void.

6.3.6 Malicious Communication Identification (MCID)

Table 6.3.6-1: Void

Table 6.3.6-2: Void

Table 6.3.6-3: Void

Table 6.3.6-4: Void


TSS reference IMS-SS/MCID/ Selection criteria PICS 6.3.1/2 AND PICS 6.3.2/3 Test Purpose name ISUP IDR is mapped into INFO request Test Purpose Ensure that on receipt of INFO with encapsulated ISUP IDR containing a MCID request

indicators indicator set to MCID_req, an INFO request is sent. A XML 'mcid' McidRequestIndicator is included set to XML_McidReq as indicated in table 6.3.6-5

ISUP Parameter values IDR: MCID request indicators MCID_req

SIP Parameter values INFO: <?xml version="1.0" mcid request> McidRequestIndicator>XML_McidReq</ HoldingIndicator>1</ INFO (IDR) no xml body present


INVITE � � INVITE (IAM) 100 Trying � � 100 Trying INFO � � INFO (IDR) 200 OK INFO � � 200 OK INFO


Table 6.3.6-5: Mapping of ISUP MCID request indicator into XML McidRequestIndicator

MCID_req XML_McidReq VA_01 MCID not requested 0 VA_02 MCID requested 1

ETSI

ETSI TS 101 572-2 V1.2.1 (2014-07)309


TSS reference IMS-SS/MCID/ Selection criteria PICS 6.3.1/2 AND PICS 6.3.2/3 Test Purpose name INFO request is mapped into ISUP IRS Test Purpose Ensure that on receipt of an INFO request the XML 'mcid' McidResponseIndicator is set to

MCID_rsp, an INFO with encapsulated ISUP IRS is sent. The MCID response indicator is set to MCID_rsp as indicated in table 6.3.6-6

ISUP Parameter values IRS: MCID response indicator MCID_rsp

SIP Parameter values INFO: <?xml version="1.0" mcid response> McidResponseIndicator>XML_McidRsp</ INFO (IDR) no xml body present


INVITE � � INVITE (IAM) 100 Trying � � 100 Trying INFO � � INFO (IDR) 200 OK INFO � � 200 OK INFO INFO � � INFO (IRS) 200 OK INFO � � 200 OK INFO


Table 6.3.6-6: Mapping of XML McidResponseIndicator into ISUP MCID response indicator

XML_McidRsp MCID_rsp VA_01 0 MCID not included VA_02 1 MCID included

ETSI

ETSI TS 101 572-2 V1.2.1 (2014-07)310


TSS reference IMS-SS/MCID/ Selection criteria PICS 6.3.1/2 AND PICS 6.3.2/3 Test Purpose name XML OrigPartyIdentity is mapped into ISUP IRS Calling Party number Test Purpose Ensure that on receipt of an INFO request the XML 'mcid' McidResponseIndicator is set to

MCID_rsp, an INFO with encapsulated ISUP IRS is sent. The XML OrigPartyIdentity is mapped into the Calling party: • If the country code of the OrigPartyIdentity URI is equal to the country code where the

SUT is located the Nature of address is set to 'National (significant) number', the '+' and the country code is removed from the user part of the XML OrigPartyIdentity URI and send in the Address signals of the Calling party number.

• If the country code of the OrigPartyIdentity URI is not equal to the country code where the SUT is located the Nature of address is set to 'International number', the '+' is removed from the user part of the XML OrigPartyIdentity URI and send in the Address signals of the Calling party number.

The XML OrigPartyPresentationRestriction value XML_orig_restr is mapped into the Address presentation restriction indicator APRI_value of the Calling party number as indicated in table 6.3.6-7

ISUP Parameter values IRS: MCID response indicator MCID included Calling Party number Address presentation restriction indicator=APRI_value Address signal= derived from the OrigPartyIdentity

SIP Parameter values INFO: <?xml version="1.0" mcid response> McidResponseIndicator>1</ OrigPartyIdentity>any valid URI</ OrigPartyPresentationRestriction>XML_orig_restr</ INFO (IDR) no xml body present




Table 6.3.6-7: Mapping of XML OrigPartyPresentationRestriction into ISUP Calling party number APRI

XML_orig_restr APRI_value VA_01 True Presentation restricted VA_02 False Presentation allowed

ETSI

ETSI TS 101 572-2 V1.2.1 (2014-07)311


TSS reference IMS-SS/MCID/ Selection criteria PICS 6.3.1/2 AND PICS 6.3.2/3 Test Purpose name XML GenericNumber is mapped into ISUP IRS Additional calling Party number Test Purpose Ensure that on receipt of an INFO request the XML 'mcid' McidResponseIndicator is set to

MCID_rsp, an INFO with encapsulated ISUP IRS is sent. The XML GenericNumber is mapped into the Additional calling party: • If the country code of the GenericNumber URI is equal to the country code where the

SUT is located the Nature of address is set to 'National (significant) number', the '+' and the country code is removed from the user part of the XML GenericNumber URI and send in the Address signals of the Additional calling party number.

• If the country code of the GenericNumber URI is not equal to the country code where the SUT is located the Nature of address is set to 'International number', the '+' is removed from the user part of the XML GenericNumber URI and send in the Address signals of the Additional calling party number.

The XML GenericNumberPresentationRestriction value XML_gen_restr is mapped into the Address presentation restriction indicator APRI_value of the Additional calling party number as indicated in table 6.3.6-8

ISUP Parameter values IRS: MCID response indicator MCID included Generic number Additional calling Party number Address presentation restriction indicator=APRI_value Address signal

SIP Parameter values INFO: <?xml version="1.0" mcid response> McidResponseIndicator>1</ GenericNumber>derived from the Generic number Address signal</ GenericNumberPresentationRestriction>XML_gen_restr</ INFO (IDR) no xml body present




Table 6.3.6-8: Mapping of XML GenericNumberPresentationRestriction into ISUP Additional calling party number APRI

XML_gen_restr APRI_value VA_01 True Presentation restricted VA_02 False Presentation allowed

ETSI

ETSI TS 101 572-2 V1.2.1 (2014-07)312

6.3.7 Closed User Group (CUG)

TP number TP_407_001 Reference [1], clause 7.2.1 [2], clauses 7.5.10.1, table, 7.5.10.1.1, table, 7.5.10.1.2

TSS reference IMS-SS/CUG/ Selection criteria PICS 6.3.2/23 AND NOT PICS 6.3.10/2 Test Purpose name Mapping of the SIP XML CUG Element to the ISUP closed usergroup interlock code

parameter Test Purpose Ensure that on receipt of an INVITE request containing the Content-Type

application/vnd.etsi.cug+xml and the 'cug' XML body, an INVITE with encapsulated IAM is sent. The XML 'networkIndicator' is mapped into the ISUP Closed user group interlock code Network Identity indicator and the XML 'cugInterlockBinaryCode' is mapped into the ISUP Closed user group interlock code Binary code indicator

ISUP Parameter values IAM: Optional forward call indicator Closed user group call indicator Closed user group interlock code Network Identity mapped from XML networkIndicator Binary code mapped from XML cugInterlockBinaryCode

SIP Parameter values INVITE: Content-Type: application/vnd.etsi.cug+xml <?xml version="1.0" cug networkIndicator=any proper value cugInterlockBinaryCode=any proper value cugCommunicationIndicator INVITE(IAM): no xml body present




ETSI

ETSI TS 101 572-2 V1.2.1 (2014-07)313

TP number TP_407_002 Reference [1], clause 7.2.1 [2], clauses 7.5.10.1, table 7.5.10.1.1, table, 7.5.10.1.3

TSS reference IMS-SS/CUG/ Selection criteria PICS 6.3.2/23 AND NOT PICS 6.3.10/2 Test Purpose name Mapping of the SIP XML CUG Element to the ISUP closed user group call indicator

included in the optional Forward Call Indicator Parameter Test Purpose Ensure that on receipt of an INVITE request containing the Content-Type

application/vnd.etsi.cug+xml and the 'cug' XML body, an INVITE with encapsulated IAM is sent. The XML 'cugCommunicationIndicator' is mapped into the ISUP Optional forward call indicator Closed user group call indicator as indicated in table 6.3.7-1

ISUP Parameter values IAM: Optional forward call indicator Closed user group call indicator=CUG_ind Closed user group interlock code Network Identity Binary code

SIP Parameter values INVITE: Content-Type: application/vnd.etsi.cug+xml <?xml version="1.0" cug networkIndicator cugInterlockBinaryCode cugCommunicationIndicator=CUG_COM_ind INVITE(IAM): no xml body present




Table 6.3.7-1: Mapping of XML cugCommunicationIndicator into ISUP Optional forward call indicator Closed user group call indicator

CUG_COM_ind CUG_ind VA_01 00 non-CUG call VA_02 01 Spare VA_03 10 closed user group call, outgoing access allowed VA_04 11 closed user group call, outgoing access not allowed

ETSI

ETSI TS 101 572-2 V1.2.1 (2014-07)314


TSS reference IMS-SS/CUG/ Selection criteria PICS 6.3.2/23 AND PICS 6.3.10/2 Test Purpose name Communication is released if the PSTN/ISDN network does not support CUG, CUG without

outgoing access Test Purpose Ensure that on receipt of an INVITE request containing the Content-Type

application/vnd.etsi.cug+xml and the 'cug' XML body the cugCommunicationIndicator set to '11', the communication is released with 403 (Forbidden) final response if the PSTN/ISDN network does not support CUG

ISUP Parameter values SIP Parameter values INVITE:

Content-Type: application/vnd.etsi.cug+xml <?xml version="1.0" cug networkIndicator cugInterlockBinaryCode cugCommunicationIndicator='11' INVITE(IAM): no xml body present


INVITE � 403 Forbidden � ACK �



TSS reference IMS-SS/CUG/ Selection criteria PICS 6.3.2/23 AND PICS 6.3.10/2 Test Purpose name Communication is treated as an ordinary call if the PSTN/ISDN network does not support

CUG, CUG with outgoing access Test Purpose Ensure that on receipt of an INVITE request containing the Content-Type

application/vnd.etsi.cug+xml and the 'cug' XML body the cugCommunicationIndicator set to '10', the communication is treated as an ordinary call if the PSTN/ISDN network does not support CUG. A Closed user group interlock code is not present in the sent INVITE with encapsulated IAM






ETSI

ETSI TS 101 572-2 V1.2.1 (2014-07)315


TSS reference IMS-SS/CUG/ Selection criteria PICS 6.3.2/23 AND PICS 6.3.10/2 Test Purpose name Communication is treated as an ordinary call if the PSTN/ISDN network does not support

CUG, Non-CUG call Test Purpose Ensure that on receipt of an INVITE request containing the Content-Type

application/vnd.etsi.cug+xml and the 'cug' XML body the cugCommunicationIndicator set to '00', the communication is treated as an ordinary call if the PSTN/ISDN network does not support CUG. A Closed user group interlock code is not present in the sent INVITE with encapsulated IAM







TSS reference IMS-SS/CUG/ Selection criteria PICS 6.3.2/23 AND NOT PICS 6.3.10/1 Test Purpose name Mapping of the ISUP closed usergroup interloccode to SIP XML CUG element Test Purpose Ensure that on receipt of an INVITE with encapsulated IAM and a Closed user group

interlock code parameter is present, an INVITE request is sent. The Network Identity indicator is mapped into the XML networkIndicator element, the Binary code is mapped into the XML cugInterlockBinaryCode

ISUP Parameter values IAM: Optional forward call indicator Closed user group call indicator Closed user group interlock code Network Identity=any proper value Binary code=any proper value

SIP Parameter values INVITE: Content-Type: application/vnd.etsi.cug+xml <?xml version="1.0" cug networkIndicator= mapped from Network Identity cugInterlockBinaryCode= mapped from Binary code cugCommunicationIndicator INVITE(IAM): no xml body present




ETSI

ETSI TS 101 572-2 V1.2.1 (2014-07)316


TSS reference IMS-SS/CUG/ Selection criteria PICS 6.3.2/23 AND NOT PICS 6.3.10/1 Test Purpose name Mapping of the ISUP closed usergroup interloccode to SIP XML CUG element Test Purpose Ensure that on receipt of an IAM and an Optional forward call indicator is present set to

CUG_ind, an INVITE request is sent. The XML cugCommunicationIndicator is mapped from the ISUP Closed user group call indicator set to CUG_ind as indicated in table 6.3.7-2

ISUP Parameter values IAM: Optional forward call indicator Closed user group call indicator=CUG_ind Closed user group interlock code Network Identity Binary code

SIP Parameter values INVITE: Content-Type: application/vnd.etsi.cug+xml <?xml version="1.0" cug networkIndicator cugInterlockBinaryCode cugCommunicationIndicator=CUG_COM_ind INVITE(IAM): no xml body present




Table 6.3.7-2: Mapping of ISUP Optional forward call indicator Closed user group call indicator into XML cugCommunicationIndicator

CUG_ind CUG_COM_ind VA_01 non-CUG call 00 VA_02 Spare 01 VA_03 closed user group call, outgoing access allowed 10 VA_04 closed user group call, outgoing access not allowed 11

ETSI

ETSI TS 101 572-2 V1.2.1 (2014-07)317

TP number TP_407_008 Reference [1], clause 7.3.1 [2], clauses 7.5.10.2, 1.5.2.4.2/Q.735.1

TSS reference IMS-SS/CUG/ Selection criteria PICS 6.3.2/23 AND PICS 6.3.10/1 AND PICS 6.3.10/1 Test Purpose name Communication is released if the IMS network does not support CUG, CUG without

outgoing access Test Purpose Ensure that on receipt of an INVITE with encapsulated IAM and the Optional forward call

indicator Closed user group call indicator is set to closed user group call, outgoing access not allowed and the IMS network does not support the CUG supplementary service, a REL is sent and the Cause value is set to #29 Facility rejected the diagnostics indicating CUG without access

ISUP Parameter values IAM: Optional forward call indicator Closed user group call indicator=C UG call, outgoing access not allowed Closed user group interlock code Network Identity Binary code REL: Cause indicator Cause value=29 Diagnostics=3


INVITE (IAM) � 500 Server Internal Error (REL) � ACK (RLC) �


TP number TP_407_009 Reference [1], clause 7.3.1 [2], clauses 7.5.10.2, 1.5.2.4.2/Q.735.1

TSS reference IMS-SS/CUG/ Selection criteria PICS 6.3.2/23 AND PICS 6.3.10/1 AND PICS 6.3.10/1 Test Purpose name Communication is treated as an ordinary call if the IMS network does not support CUG,

CUG with outgoing access Test Purpose Ensure that on receipt of an IAM and the Optional forward call indicator Closed user group

call indicator is set to closed user group call, outgoing access allowed and the IMS network does not support the CUG supplementary service, the communication is treated as an ordinary call

ISUP Parameter values IAM: Optional forward call indicator Closed user group call indicator=C UG call, outgoing access allowed Closed user group interlock code Network Identity Binary code




ETSI

ETSI TS 101 572-2 V1.2.1 (2014-07)318

6.3.8 Call Completion Services

TP number TP_408_001 Reference [1] 7.7.10.3 [2] 7.5.11.1, table 7.5.11.1.1

TSS reference IMS-SS/CC/ Selection criteria PICS 6.3.1/2 AND PICS 6.3.2/24 Test Purpose name Mapping of CCNR possible indication in the ACM Test Purpose Ensure that on receipt of a 180 Ringing with encapsulated ACM and a CCNR possible

indicator is present set to 'CCNR possible' a 180 Ringing is sent. A Call-Info header is present, the URI is derived from the Called party number, the purpose parameter is set to 'call-completion', the m parameter is set to 'NR'.

ISUP Parameter values IAM: Called party number Number digits ACM: Called party status Subscriber free CCNR possible indicator CCNR possible

SIP Parameter values 180: Call-Info: <sip:Called party number digits>;purpose=call-completion;m=NR Comments Message flows SIP NNI MGCF SIP-I

INVITE � � INVITE(IAM) 180 Ringing � � 180 Ringing(ACM)



TSS reference IMS-SS/CC/ Selection criteria PICS 6.3.1/2 AND PICS 6.3.2/24 Test Purpose name Mapping of CCNR possible indication in the CPG Test Purpose Ensure that on receipt of a 180 Ringing with encapsulated CPG Event indicator set to

'Alerting' and a CCNR possible indicator is present set to 'CCNR possible' a 180 Ringing is sent. A Call-Info header is present, the URI is derived from the Called party number, the purpose parameter is set to 'call-completion', the m parameter is set to 'NR'.

ISUP Parameter values IAM: Called party number Number digits ACM: Called party status No indication CPG: Event indicator Alerting CCNR possible indicator CCNR possible

SIP Parameter values 180: Call-Info: <sip:Called party number digits>;purpose=call-completion;m=NR Comments Message flows SIP NNI MGCF SIP-I

INVITE � � INVITE(IAM) � 183 Session Progress(ACM(no indication)) 180 Ringing � � 180 Ringing(CPG(Alerting))


ETSI

ETSI TS 101 572-2 V1.2.1 (2014-07)319


TSS reference IMS-SS/CC/ Selection criteria PICS 6.3.1/2 AND PICS 6.3.2/24 Test Purpose name Mapping of CCBS possible indication in the REL Test Purpose Ensure that on receipt of a 486 Busy Here with encapsulated ISUP REL message Cause

#17 and a CCBS possible indicator in the Diagnostic field is set to 'CCBS possible' a 486 Busy here is sent. A Call-Info header is present, the URI is derived from the Called party number, the purpose parameter is set to 'call-completion', the m parameter is set to 'BS'.

ISUP Parameter values IAM: Called party number Number digits REL: Cause indicator Cause = 17 Diagnostic CCBS possible

SIP Parameter values 486: Call-Info: <sip:Called party number digits>;purpose=call-completion;m=BS Comments Message flows SIP NNI MGCF SIP-I

INVITE � � INVITE(IAM) 486 Busy here � � 486 Busy Here(REL) ACK � � ACK



TSS reference IMS-SS/CC/ Selection criteria PICS 6.3.1/2 AND PICS 6.3.2/24 Test Purpose name Mapping of m parameter in the INVITE request URI into CCSS parameter in the IAM Test Purpose Ensure that on receipt of an INVITE request and a m parameter set to 'BS' or 'NR' an

INVITE request with an encapsulated ISUP IAM is sent and the CCSS call indicator parameter is present and the value is set to 'CCSS call'.

ISUP Parameter values IAM: CCSS call indicator CCSS call

SIP Parameter values INVITE: <Request URI>;m=NR or ;m=BS Comments Message flows SIP NNI MGCF SIP-I

INVITE � � INVITE(IAM) 100 Trying �



TSS reference IMS-SS/CC/ Selection criteria PICS 6.3.1/2 AND PICS 6.3.2/24 Test Purpose name Mapping of Call-Info header in the INVITE into CCSS parameter in the IAM Test Purpose Ensure that on receipt of an INVITE request and a Call-Info header is present the purpose

parameter is set to 'call-completion' and the m parameter set to 'BS' or 'NR' an IAM is sent and the CCSS call indicator parameter is present and the value is set to 'CCSS call'.


SIP Parameter values INVITE: <Request URI> Call-Info: <sip:Called party number digits>;purpose=call-completion; m=BS or NR


INVITE � � INVITE(IAM) 100 Trying �


ETSI

ETSI TS 101 572-2 V1.2.1 (2014-07)320


TSS reference IMS-SS/CC/ Selection criteria PICS 6.3.1/2 AND PICS 6.3.2/24 Test Purpose name Invocation of CCBS in the I-MGCF m parameter in Start line Test Purpose Ensure that on receipt of a SUBSCRIBE request the Request URI contains the m

parameter set to 'BS' and Event header field contains the value 'call-completion', an M3UA SCCP UDT or XUDT is sent containing a TC-Begin REQUEST invoke Data field. The TC-Begin REQUEST invoke CalledPartyNumber is derived from the To header, the CallingPartyNumber is derived from the From header and the RetainSupported is set to 'TRUE'.

TCAP Parameter values TC Begin CCBS REQUEST invoke CalledPartyNumber derived from the To header CallingPartyNumber derived from the P-Asserted-Identity header RetainSupported TRUE

SIP Parameter values SUBSCRIBE: <Request URI>, m=BS Event: call-completion

Comments Message flows SIP NNI MGCF M3UA

SUBSCRIBE � � DATA (SCCP (TC-Begin)) 202 Accepted �



TSS reference IMS-SS/CC/ Selection criteria PICS 6.3.1/2 AND PICS 6.3.2/24 Test Purpose name Invocation of CCBS in the I-MGCF m parameter in Call-Info header Test Purpose Ensure that on receipt of a SUBSCRIBE and the Event header field contains the value

'call-completion' and a Call-Info header with purpose parameter ser to call-completion and m parameter set to 'BS', an M3UA SCCP UDT or XUDT is sent containing a TC-Begin REQUEST invoke Data field. The TC-Begin REQUEST invoke CalledPartyNumber is derived from the To header, the CallingPartyNumber is derived from the From header and the RetainSupported is set to 'TRUE'.

TCAP Parameter values TC Begin CCBS REQUEST invoke CalledPartyNumber derived from the To header CallingPartyNumber derived from the P-Asserted-Identity header RetainSupported TRUE

SIP Parameter values SUBSCRIBE: <Requesr URI> Event: call-completion Call-Info: <sip:Calling party number digits>;purpose=call-completion; m=BS




ETSI

ETSI TS 101 572-2 V1.2.1 (2014-07)321


TSS reference IMS-SS/CC/ Selection criteria PICS 6.3.1/2 AND PICS 6.3.2/24 Test Purpose name Invocation of CCNR in the I-MGCF m parameter in Start line Test Purpose Ensure that on receipt of a SUBSCRIBE request the Request URI contains the m

parameter set to 'NR' and Event header field contains the value 'call-completion', an M3UA SCCP UDT or XUDT is sent containing a TC-Begin REQUEST invoke Data field. The TC-Begin REQUEST invoke CalledPartyNumber is derived from the To header, the CallingPartyNumber is derived from the From header and the RetainSupported is set to 'TRUE'.

TCAP Parameter values TC Begin CCNR REQUEST invoke CalledPartyNumber derived from the To header CallingPartyNumber derived from the P-Asserted-Identity header RetainSupported TRUE

SIP Parameter values SUBSCRIBE: <Request URI>, m=NR Event: call-completion





TSS reference IMS-SS/CC/ Selection criteria PICS 6.3.1/2 AND PICS 6.3.2/24 Test Purpose name Invocation of CCNR in the I-MGCF m parameter in Call-Info header Test Purpose Ensure that on receipt of a SUBSCRIBE and the Event header field contains the value

'call-completion' and a Call-Info header with purpose parameter ser to call-completion and m parameter set to 'NR', an M3UA SCCP UDT or XUDT is sent containing a TC-Begin REQUEST invoke Data field. The TC-Begin REQUEST invoke CalledPartyNumber is derived from the To header, the CallingPartyNumber is derived from the From header and the RetainSupported is set to 'TRUE'.

TCAP Parameter values TC Begin CCNR REQUEST invoke CalledPartyNumber derived from the To header CallingPartyNumber derived from the P-Asserted-Identity header RetainSupported TRUE

SIP Parameter values SUBSCRIBE: <Request URI> Event: call-completion Call-Info: <sip:Calling party number digits>;purpose=call-completion; m=NR




ETSI

ETSI TS 101 572-2 V1.2.1 (2014-07)322


TSS reference IMS-SS/CC/ Selection criteria PICS 6.3.1/2 AND PICS 6.3.2/24 Test Purpose name PUBLISH with m=BS parameter in the Request line and PIDF basic status "closed" is

interworked into CCBS SUSPEND Test Purpose Ensure that on receipt of a PUBLISH request and a m parameter is present in the Request

line is set to 'BS' the Event header field contains the value 'presence', and a PIDF XML MIME body is present the presence status set to 'closed', an M3UA SCCP UDT or XUDT is sent containing a TC-Cont CCBS SUSPEND Data field.

TCAP Parameter values TC-Cont: CCBS SUSPEND SIP Parameter values PUBLISH: <Request URI>; m=BS

Event: presence Content-Type: application/pidf+xml <?xml version="1.0" encoding="UTF-8"?> <presence <status> <basic>closed</basic>

Comments Note the XML semantic is schematically the alias is not considered. Message flows SIP NNI MGCF M3UA

Invoke a successful CCBS request and remote user is now free PUBLISH � � DATA (SCCP (TC-Cont)) 200 OK (PUBLISH) �



TSS reference IMS-SS/CC/ Selection criteria PICS 6.3.1/2 AND PICS 6.3.2/24 Test Purpose name PUBLISH with m=BS parameter in Call-Info header and PIDF basic status "closed" is

interworked into CCBS SUSPEND Test Purpose Ensure that on receipt of a PUBLISH request the Event header field contains the value

'presence' and a Call-Info header with purpose parameter ser to call-completion and m parameter set to 'BS' and a PIDF XML MIME body is present the presence status set to 'closed', an M3UA SCCP UDT or XUDT is sent containing a TC-Cont CCBS SUSPEND Data field.

TCAP Parameter values TC-Cont: CCBS SUSPEND SIP Parameter values PUBLISH: <Request URI>

Event: presence Call-Info: <sip:Calling party number digits>;purpose=call-completion; m=BS Content-Type: application/pidf+xml <?xml version="1.0" encoding="UTF-8"?> <presence <status> <basic>closed</basic>


Invoke a successful CCBS request and remote user is now free PUBLISH � � DATA (SCCP (TC-Cont)) 200 OK (PUBLISH) �


ETSI

ETSI TS 101 572-2 V1.2.1 (2014-07)323


TSS reference IMS-SS/CC/ Selection criteria PICS 6.3.1/2 AND PICS 6.3.2/24 Test Purpose name PUBLISH with m=BS parameter in the Request line and PIDF basic status "open" is

interworked into CCBS RESUME Test Purpose Ensure that on receipt of a PUBLISH request and a m parameter is present in the Request

line is set to 'BS' the Event header field contains the value 'presence' and a PIDF XML MIME body is present the presence status set to 'open', an M3UA SCCP UDT or XUDT is sent containing a TC-Cont CCBS RESUME Data field.

TCAP Parameter values TC-Cont: CCBS RESUME SIP Parameter values PUBLISH: <Request URI>; m=BS

Event: presence Content-Type: application/pidf+xml <?xml version="1.0" encoding="UTF-8"?> <presence <status> <basic>open</basic>


Successful CCBS request and remote user is free originating user suspended PUBLISH � � DATA (SCCP (TC-Cont)) 200 OK (PUBLISH) �



TSS reference IMS-SS/CC/ Selection criteria PICS 6.3.1/2 AND PICS 6.3.2/24 Test Purpose name PUBLISH with m=BS parameter in Call-Info header and PIDF basic status "open" is

interworked into CCBS RESUME Test Purpose Ensure that on receipt of a PUBLISH request and the Event header field contains the value

'presence', a Call-Info header with purpose parameter ser to call-completion and m parameter set to 'BS' and a PIDF XML MIME body is present the presence status set to 'open', an M3UA SCCP UDT or XUDT is sent containing a TC-Cont CCBS RESUME Data field.

TCAP Parameter values TC-Cont: CCBS RESUME SIP Parameter values PUBLISH: <Request URI>

Event: presence Call-Info: <sip:Calling party number digits>;purpose=call-completion; m=BS Content-Type: application/pidf+xml <?xml version="1.0" encoding="UTF-8"?> <presence <status> <basic>open</basic>


Successful CCBS request and remote user is free originating user suspended PUBLISH � � DATA (SCCP (TC-Cont)) 200 OK (PUBLISH) �


ETSI

ETSI TS 101 572-2 V1.2.1 (2014-07)324


TSS reference IMS-SS/CC/ Selection criteria PICS 6.3.1/2 AND PICS 6.3.2/24 Test Purpose name PUBLISH with m=NR parameter in the Request line and PIDF basic status "closed" is

interworked into CCBS SUSPEND Test Purpose Ensure that on receipt of a PUBLISH request and a m parameter is present in the Request

line is set to 'NR' the Event header field contains the value 'presence' and a PIDF XML MIME body is present the presence status set to 'closed', an M3UA SCCP UDT or XUDT is sent containing a TC-Cont CCBS SUSPEND Data field.

TCAP Parameter values TC-Cont: CCBS SUSPEND SIP Parameter values PUBLISH: <Request URI>; m=NR

Event: presence Content-Type: application/pidf+xml <?xml version="1.0" encoding="UTF-8"?> <presence <status> <basic>closed</basic>


Invoke a successful CCNR request and remote user is now free PUBLISH � � DATA (SCCP (TC-Cont)) 200 OK (PUBLISH) �



TSS reference IMS-SS/CC/ Selection criteria PICS 6.3.1/2 AND PICS 6.3.2/24 Test Purpose name PUBLISH with m=NR parameter in Call-Info header and PIDF basic status "closed" is

interworked into CCBS SUSPEND Test Purpose Ensure that on receipt of a PUBLISH request the Event header field contains the value

'presence', a Call-Info header with purpose parameter ser to call-completion and m parameter set to 'NR' and a PIDF XML MIME body is present the presence status set to 'closed', an M3UA SCCP UDT or XUDT is sent containing a TC-Cont CCBS SUSPEND Data field.

TCAP Parameter values TC-Cont: CCBS SUSPEND SIP Parameter values PUBLISH: <Request URI>

Event: presence Call-Info: <sip:Calling party number digits>;purpose=call-completion; m=NR Content-Type: application/pidf+xml <?xml version="1.0" encoding="UTF-8"?> <presence <status> <basic>closed</basic>


Invoke a successful CCNR request and remote user is now free PUBLISH � � DATA (SCCP (TC-Cont)) 200 OK (PUBLISH) �


ETSI

ETSI TS 101 572-2 V1.2.1 (2014-07)325


TSS reference IMS-SS/CC/ Selection criteria PICS 6.3.1/2 AND PICS 6.3.2/24 Test Purpose name PUBLISH with m=NR parameter in the Request line and PIDF basic status "open" is

interworked into CCBS RESUME Test Purpose Ensure that on receipt of a PUBLISH request and a m parameter is present in the Request

line is set to 'NR' the Event header field contains the value 'presence' and a PIDF XML MIME body is present the presence status set to 'open', an M3UA SCCP UDT or XUDT is sent containing a TC-Cont CCBS RESUME Data field.

TCAP Parameter values TC-Cont: CCBS RESUME SIP Parameter values PUBLISH: <Request URI>; m=NR

Event: presence Content-Type: application/pidf+xml <?xml version="1.0" encoding="UTF-8"?> <presence <status> <basic>open</basic>


Successful CCNR request and remote user is free originating user suspended PUBLISH � � DATA (SCCP (TC-Cont)) 200 OK (PUBLISH) �



TSS reference IMS-SS/CC/ Selection criteria PICS 6.3.1/2 AND PICS 6.3.2/24 Test Purpose name PUBLISH with m=NR parameter in Call-Info header and PIDF basic status "open" is

interworked into CCBS RESUME Test Purpose Ensure that on receipt of a PUBLISH request and Event header field contains the value

'presence' a Call-Info header with purpose parameter ser to call-completion and m parameter set to 'NR' and a PIDF XML MIME body is present the presence status set to 'open', an M3UA SCCP UDT or XUDT is sent containing a TC-Cont CCBS RESUME Data field.

TCAP Parameter values TC-Cont: CCBS RESUME SIP Parameter values PUBLISH: <Request URI>

Event: presence Call-Info: <sip:Calling party number digits>;purpose=call-completion; m=NR Content-Type: application/pidf+xml <?xml version="1.0" encoding="UTF-8"?> <presence <status> <basic>open</basic>


Successful CCNR request and remote user is free originating user suspended PUBLISH � � DATA (SCCP (TC-Cont)) 200 OK (PUBLISH) �


ETSI

ETSI TS 101 572-2 V1.2.1 (2014-07)326


TSS reference IMS-SS/CC/ Selection criteria PICS 6.3.1/2 AND PICS 6.3.2/24 Test Purpose name SUBSCRIBE with m=BS and Expires header set to '0' is interworked into CCBS CANCEL Test Purpose Ensure that on receipt of a SUBSCRIBE request and a m parameter is present in the

Request line is set to 'BS' or a Call-Info header with purpose parameter ser to call-completion and m parameter set to 'BS' and Event header field contains the value 'call-completion' and an Expires header set to '0', an M3UA SCCP UDT or XUDT is sent containing a TC-End CCBS CANCEL Data field.

TCAP Parameter values TC-End: CCBS CANCEL SIP Parameter values SUBSCRIBE: <Request URI>; m=BS

Event:call-completion Call-Info: <sip:Calling party number digits>;purpose=call-completion; m=BS Expires: 0


A CCBS is successfully invoked SUBSCRIBE � � DATA (SCCP (TC-End)) 202 Accepted �



TSS reference IMS-SS/CC/ Selection criteria PICS 6.3.1/2 AND PICS 6.3.2/24 Test Purpose name SUBSCRIBE with m=NR and Expires header set to '0' is interworked into CCBS CANCEL Test Purpose Ensure that on receipt of a SUBSCRIBE request and a m parameter is present in the

Request line is set to 'NR' or a Call-Info header with purpose parameter ser to call-completion and m parameter set to 'BS' and Event header field contains the value 'call-completion' and an Expires header set to '0', an M3UA SCCP UDT or XUDT is sent containing a TC-End CCBS CANCEL Data field.

TCAP Parameter values TC-End: CCBS CANCEL SIP Parameter values SUBSCRIBE: <Request URI>; m=NR

Event:call-completion Call-Info: <sip:Calling party number digits>;purpose=call-completion; m=NR Expires: 0


A CCNR is successfully invoked SUBSCRIBE � � DATA (SCCP (TC-End)) 202 Accepted �


ETSI

ETSI TS 101 572-2 V1.2.1 (2014-07)327


TSS reference IMS-SS/CC/ Selection criteria PICS 6.3.1/2 AND PICS 6.3.2/24 Test Purpose name TC-Cont CCBS REQUEST (return result) is interworked into NOTIFY cc-service-retention

present Test Purpose Ensure that on receipt of an M3UA UDT or XUDT containing a TC-Cont CCBS REQUEST

(return result) Data field and the RetainSupported element is set to TRUE, a NOTIFY request is sent and the cc-state body is set to 'queued' the cc-service-retention body is set to 'true'.

TCAP Parameter values TC-Cont: CCBS REQUEST (return result) RetainSupported=TRUE

SIP Parameter values NOTIFY: Event: call-completion Content-Type: application/call-completion cc-state: queued cc-service-retention: true


SUBSCRIBE � � (X)UDT (TC-Begin) 202 Accepted � NOTIFY � � DATA (SCCP (TC-Cont)) 200 OK (NOTIFY) �



TSS reference IMS-SS/CC/ Selection criteria PICS 6.3.1/2 AND PICS 6.3.2/24 Test Purpose name TC-Cont CCBS REQUEST (return result) is interworked into NOTIFY cc-service-retention

not present Test Purpose Ensure that on receipt of an M3UA UDT or XUDT containing a TC-Cont CCBS REQUEST

(return result) Data field and the RetainSupported element is set to FALSE, a NOTIFY request is sent and the cc-state body is set to 'queued' a cc-service-retention body is not present.

TCAP Parameter values TC-Cont: CCBS REQUEST (return result) RetainSupported=FALSE

SIP Parameter values NOTIFY: Event: call-completion Content-Type: application/call-completion cc-state: queued


SUBSCRIBE � � DATA (SCCP (TC-Begin)) 202 Accepted � NOTIFY � � DATA (SCCP (TC-Cont)) 200 OK (NOTIFY) �


ETSI

ETSI TS 101 572-2 V1.2.1 (2014-07)328


TSS reference IMS-SS/CC/ Selection criteria PICS 6.3.1/2 AND PICS 6.3.2/24 Test Purpose name CCBS Return error TC-End ShortTermDenial received, 480 Temporarily Unavailable

response to SUBCRIBE Test Purpose Ensure that on receipt of an M3UA UDT or XUDT containing a TC-End CCBS REQUEST

(Return error) component in the Data field set to 'ShortTermDenial', a 480 Temporarily Unavailable final response to the SUBCRIBE CCBS request is sent.

TCAP Parameter values TC Begin CCBS REQUEST invoke TC-End CCBS REQUEST (Return error) ShortTermDenial



SUBCRIBE � � DATA (SCCP (TC-Begin)) 480 Temporarily Unavailable � � DATA (SCCP (TC-End))



TSS reference IMS-SS/CC/ Selection criteria PICS 6.3.1/2 AND PICS 6.3.2/24 Test Purpose name CCBS Return error TC-End LongTermDenial received, 403 Forbidden unavailable

response to SUBCRIBE Test Purpose Ensure that on receipt of an M3UA UDT or XUDT containing a TC-End CCBS REQUEST

(Return error) component in the Data field set to 'LongTermDenial', a 403 Forbidden final response to the SUBCRIBE CCBS request is sent.

TCAP Parameter values TC Begin CCBS REQUEST invoke TC-End CCBS REQUEST (Return error) LongTermDenial



SUBSCRIBE � � DATA (SCCP (TC-Begin)) 403 Forbidden � � DATA (SCCP (TC-End))



TSS reference IMS-SS/CC/ Selection criteria PICS 6.3.1/2 AND PICS 6.3.2/24 Test Purpose name CCNR Return error TC-End ShortTermDenial received, 480 Temporarily Unavailable

response to SUBCRIBE Test Purpose Ensure that on receipt of an M3UA UDT or XUDT containing a TC-End CCNR REQUEST

(Return error) component in the Data field set to 'ShortTermDenial', a 480 Temporarily Unavailable final response to the SUBCRIBE CCNR request is sent.

TCAP Parameter values TC Begin CCNR REQUEST invoke TC-End CCNR REQUEST (Return error) ShortTermDenial



SUBCRIBE � � DATA (SCCP (TC-Begin)) 480 Temporarily Unavailable � � DATA (SCCP (TC-End))


ETSI

ETSI TS 101 572-2 V1.2.1 (2014-07)329


TSS reference IMS-SS/CC/ Selection criteria PICS 6.3.1/2 AND PICS 6.3.2/24 Test Purpose name CCNR Return error TC-End LongTermDenial received, 403 Forbidden unavailable

response to SUBCRIBE Test Purpose Ensure that on receipt of a M3UA SCCP containing a TC-End CCNR REQUEST (Return

error) component in the Data field set to 'LongTermDenial', a 403 Forbidden final response to the SUBCRIBE CCNR request is sent.

TCAP Parameter values TC Begin CCNR REQUEST invoke TC-End CCNR REQUEST (Return error) LongTermDenial



SUBSCRIBE � � DATA (SCCP (TC-Begin)) 403 Forbidden � � DATA (SCCP (TC-End))



TSS reference IMS-SS/CC/ Selection criteria PICS 6.3.1/2 AND PICS 6.3.2/24 Test Purpose name TC-End CCBS CANCEL received after CCBS was successfully invoked Test Purpose Ensure that on receipt of an M3UA SCCP containing a TC-End CCBS CANCEL after a

CCBS was successfully invoked, a NOTIFY request is sent containing a m parameter set to 'BS' in the Request line and a Subscription-State header set to 'terminated ' and the subexp-params reason set to 'noresource'.

TCAP Parameter values TC-End CCBS CANCEL

SIP Parameter values NOTIFY : <Request URI> Event:call-completion Subscription-State: terminated; reason=noresource


CCBS request successfully invoked NOTIFY � � DATA (SCCP (TC-End)) 200 OK NOTIFY �



TSS reference IMS-SS/CC/ Selection criteria PICS 6.3.1/2 AND PICS 6.3.2/24 Test Purpose name TC-End CCBS CANCEL received after CCNR was successfully invoked Test Purpose Ensure that on receipt of an M3UA SCCP containing a TC-End CCBS CANCEL after a

CCNR was successfully invoked, a NOTIFY request is sent containing a m parameter set to 'NR' in the Request line and a Subscription-State header set to 'terminated ' and the subexp-params reason set to 'noresource'.


SIP Parameter values NOTIFY : <Request URI> Event:call-completion Subscription-State: terminated; reason=noresource


CCNR request successfully invoked NOTIFY � � DATA (SCCP (TC-End)) 200 OK NOTIFY �


ETSI

ETSI TS 101 572-2 V1.2.1 (2014-07)330


TSS reference IMS-SS/CC/ Selection criteria PICS 6.3.1/2 AND PICS 6.3.2/24 Test Purpose name Interworking of Remote user free indication at the I-MGCF Test Purpose Ensure that on receipt of an M3UA UDT or XUDT containing a TC-Cont REMOTE USER

FREE invoke component in the Data field, a NOTIFY request is sent and a cc-state body is present set to 'ready'.

TCAP Parameter values TC-Cont CCBS REMOTE USER FREE

SIP Parameter values NOTIFY: Event: call-completion Content-Type: application/call-completion cc-state: ready


CCNR request successfully invoked NOTIFY � � DATA (SCCP (TC-Cont)) 200 OK (NOTIFY) �


TP number TP_408_029 Reference [1] 7.7.10 [2] 7.5.11.2, table 7.5.11.2.1

TSS reference IMS-SS/CC/ Selection criteria PICS 6.3.1/2 AND PICS 6.3.2/24 Test Purpose name Mapping of CCNR possible indication in a 180 into the CCNR possible indicator in the ACM Test Purpose Ensure that on receipt of a 180 Ringing provisional response and a Call-Info header is

present set to the URI of the terminating user and a purpose parameter set to 'call-completion' and m parameter ser to 'NR', a 180 Ringing with encapsulated ISUP ACM is sent and a CCNR possible indicator Parameter is present set to 'CCNR possible'.

ISUP Parameter values IAM: Called party number Number digits ACM: Called party status Subscriber free CCNR possible indicator CCNR possible

SIP Parameter values 180: Call-Info: <sip:Called party number digits>;purpose=call-completion Comments Message flows SIP-I MGCF SIP NNI

INVITE(IAM) � � INVITE 180 Ringing (ACM) � � 180 Ringing



TSS reference IMS-SS/CC/ Selection criteria PICS 6.3.1/2 AND PICS 6.3.2/24 Test Purpose name 486 with Call-Info header is mapped into REL cause 17 and CCBS possible Test Purpose Ensure that on receipt of a 486 Busy Here and a Call-Info header is present set to the URI

of the terminating user and a purpose parameter set to 'call-completion' and m parameter ser to 'BS', a 486 Busy Here with encapsulated ISUP REL message is sent and the Cause value is set to 17 or 34 the Diagnostics is set to 'CCBS possible'.

ISUP Parameter values REL: Cause indicator Cause=17 or 34 Diagnostics= CCBS possible

SIP Parameter values 486: Call-Info: <sip:Called party number digits>;purpose=call-completion Comments Message flows SIP-I MGCF SIP NNI

INVITE(IAM) � � INVITE 486 Busy Here (REL) � � 486 Busy Here ACK � � ACK


ETSI

ETSI TS 101 572-2 V1.2.1 (2014-07)331


TSS reference IMS-SS/CC/ Selection criteria PICS 6.3.1/2 AND PICS 6.3.2/24 Test Purpose name CCSS call indicator in IAM is mapped into the m parameter in the Request line in the sent

INVITE Test Purpose Ensure that on receipt of an INVITE request with encapsulated ISUP IAM and a CCSS call

indicator parameter is present set to 'CCSS call', an INVITE request is sent and the Request line contains a m parameter set to 'NR' or 'BS'.


SIP Parameter values INVITE: <Request URI>;m=NR or ;m=BS Call-Info: <sip:Called party number digits>;purpose=call-completion; m=BS or NR


INVITE(IAM) � � INVITE � 100 Trying



TSS reference IMS-SS/CC/ Selection criteria PICS 6.3.1/2 AND PICS 6.3.2/24 Test Purpose name TC-Begin CCBS REQUEST (invoke) is mapped into SUBCRIBE request invokes CCBS Test Purpose Ensure that on receipt of an M3UA SCCP containing a TC-Begin CCBS REQUEST

(invoke) component, a SUBSCRIBE request is sent and the From and the P-Asserted-Identity header are derived from the CCBS REQUEST CallingPartyNumber the To header is derived from the CCBS REQUEST CalledPartyNumber the Event header field is set to 'call-completion' the Request line contains the m parameter set to 'BS'.

TCAP Parameter values TC-Begin CCBS REQUEST invoke CalledPartyNumber CallingPartyNumber retainSupported TRUE

SIP Parameter values SUBSCRIBE: <Request URI>, m=BS From: <derived from the CCBS REQUEST CallingPartyNumber > To: <derived from the CCBS REQUEST CalledPartyNumber > P-Asserted-Identity: <derived from the CCBS REQUEST CallingPartyNumber > Event: call-completion Expires: <any value>

Comments Message flows M3UA MGCF SIP NNI

DATA (SCCP (TC-Begin)) � � SUBSCRIBE � 202 Accepted


ETSI

ETSI TS 101 572-2 V1.2.1 (2014-07)332


TSS reference IMS-SS/CC/ Selection criteria PICS 6.3.1/2 AND PICS 6.3.2/24 Test Purpose name TC-Begin CCNR REQUEST (invoke) is mapped into SUBCRIBE request invokes CCNR Test Purpose Ensure that on receipt of an M3UA SCCP containing a TC-Begin CCNR REQUEST

(invoke) component, a SUBSCRIBE request is sent and the From and the P-Asserted-Identity header are derived from the CCNR REQUEST CallingPartyNumber the To header is derived from the CCNR REQUEST CalledPartyNumber the Event header field is set to 'call-completion' the Request line contains the m parameter set to 'NR'.

TCAP Parameter values TC-Begin CCNR REQUEST invoke CalledPartyNumber CallingPartyNumber retainSupported TRUE

SIP Parameter values SUBSCRIBE: <Request URI>, m=NR From: <derived from the CCNR REQUEST CallingPartyNumber > To: <derived from the CCNR REQUEST CalledPartyNumber > P-Asserted-Identity: <derived from the CCBS REQUEST CallingPartyNumber > Event: call-completion Expires: <any value>


DATA (SCCP (TC-Begin)) � � SUBSCRIBE � 202 Accepted



TSS reference IMS-SS/CC/ Selection criteria PICS 6.3.1/2 AND PICS 6.3.2/24 Test Purpose name TC-Cont CCBS SUSPEND is interworked into PUBLISH with m=BS and PIDF basic status

"closed" Test Purpose CCBS or CCNR is invoked and the remote user is free. Ensure that on receipt of an M3UA

SCCP TC-Cont CCBS SUSPEND invoke component, a PUBLISH request is sent containing the m parameter in the Request URI set to 'BS' or 'NR' the Event header set to 'presence' and a PIDF XML MIME body is present the presence status set to 'closed'.

TCAP Parameter values TC-Cont CCBS SUSPEND

SIP Parameter values PUBLISH: <Request URI>; m=BS or ;m=NR Event: presence Content-Type: application/pidf+xml <?xml version="1.0" encoding="UTF-8"?> <presence <status> <basic>closed</basic>

Comments Note the XML semantic is schematically the alias is not considered. Message flows M3UA MGCF SIP NNI

Invoke a successful CCBS/CCNR request and remote user is now free DATA (SCCP (TC-Cont)) � � PUBLISH � 200 OK (PUBLISH)


ETSI

ETSI TS 101 572-2 V1.2.1 (2014-07)333


TSS reference IMS-SS/CC/ Selection criteria PICS 6.3.1/2 AND PICS 6.3.2/24 Test Purpose name TC-Cont CCBS RESUME is interworked into PUBLISH with m=NR and PIDF basic status

"open" Test Purpose CCBS or CCNR is invoked and the remote user is free the originating user is suspended.

Ensure that on receipt of an M3UA SCCP TC-Cont CCBS SUSPEND invoke component, a PUBLISH request is sent containing the m parameter in the Request URI set to 'BS' or 'NR' the Event header set to 'presence' and a PIDF XML MIME body is present the presence status set to 'open'.

TCAP Parameter values TC-Cont CCBS RESUME

SIP Parameter values PUBLISH: <Request URI>;m='BS' or ;m=NR Event: presence Content-Type: application/pidf+xml <?xml version="1.0" encoding="UTF-8"?> <presence <status> <basic>open</basic>

Comments Note the XML semantic is schematically the alias is not considered. Message flows M3UA MGCF SIP NNI

Successful CCBS/CCNR request and originating user suspended DATA (SCCP (TC-Cont)) � � PUBLISH � 200 OK (PUBLISH)



TSS reference IMS-SS/CC/ Selection criteria PICS 6.3.1/2 AND PICS 6.3.2/24 Test Purpose name TC-End CCBS CANCEL is interworked into SUBSCRIBE with m=BS or NR and Expires

header set to '0' Test Purpose A CCBS or CCNR is successfully invoked. Ensure that on receipt of a UDT or XUDT

containing an M3UA SCCP TC-End CCBS CANCEL Data field, a SUBSCRIBE request is sent and a m parameter is present in the Request URI set to 'BS' or 'NR the Event header field is set to 'call-completion' and the Expires header is set to '0'.

TCAP Parameter values TC-End: CCBS CANCEL SIP Parameter values SUBSCRIBE: <Request URI>; m=BS or ;m='NR'

Event:call-completion Call-Info: <sip:Calling party number digits>;purpose=call-completion; m=BS or m=NR Expires: 0


A CCBS or CCNR is successfully invoked DATA (SCCP (TC-End)) � � SUBSCRIBE � 202 Accepted


ETSI

ETSI TS 101 572-2 V1.2.1 (2014-07)334


TSS reference IMS-SS/CC/ Selection criteria PICS 6.3.1/2 AND PICS 6.3.2/24 Test Purpose name A NOTIFY cc-state 'queued' and cc-service-retention 'true' is mapped into a TC-Cont

CCBS REQUEST (return result) retain supported Test Purpose Ensure that on receipt of a NOTIFY request the Event header field is set to 'call-completion'

the cc-state body is set to 'queued' and the cc-service-retention body is set to 'true', an M3UA SCCP TC-Cont is sent and the CCBS REQUEST (return result) component is present the RetainSupported element is set to 'TRUE'.

TCAP Parameter values TC-Cont: CCBS REQUEST (return result) RetainSupported=TRUE



CCBS request already invoked DATA (SCCP (TC-Cont)) � � NOTIFY � 200 OK (NOTIFY)



TSS reference IMS-SS/CC/ Selection criteria PICS 6.3.1/2 AND PICS 6.3.2/24 Test Purpose name A NOTIFY cc-state 'queued' and no cc-service-retention body present is mapped into a

TC-Cont CCBS REQUEST (return result) retain not supported Test Purpose Ensure that on receipt of a NOTIFY request the Event header field is set to 'call-completion'

the cc-state body is set to 'queued' and the cc-service-retention body is not present, an M3UA SCCP TC-Cont is sent and the CCBS REQUEST (return result) component is present the RetainSupported element is set to 'FALSE'.

TCAP Parameter values TC-Cont: CCBS REQUEST (return result) RetainSupported=FALSE



CCBS request already invoked DATA (SCCP (TC-Cont)) � � NOTIFY � 200 OK (NOTIFY)


ETSI

ETSI TS 101 572-2 V1.2.1 (2014-07)335



CCNR REQUEST (return result) retain supported Test Purpose Ensure that on receipt of a NOTIFY request the Event header field is set to 'call-completion'

the cc-state body is set to 'queued' and the cc-service-retention body is set to 'true', an M3UA SCCP TC-Cont is sent and the CCNR REQUEST (return result) component is present the RetainSupported element is set to 'TRUE'.

TCAP Parameter values TC-Cont: CCNR REQUEST (return result) RetainSupported=TRUE



CCNR request already invoked DATA (SCCP (TC-Cont)) � � NOTIFY � 200 OK (NOTIFY)




CCNR REQUEST (return result) retain not supported Test Purpose Ensure that on receipt of a NOTIFY request the Event header field is set to 'call-completion'

the cc-state body is set to 'queued' and the cc-service-retention body is not present, an M3UA SCCP TC-Cont is sent and the CCNR REQUEST (return result) component is present the RetainSupported element is set to 'FALSE'.

TCAP Parameter values TC-Cont: CCNR REQUEST (return result) RetainSupported=FALSE



CCNR request already invoked DATA (SCCP (TC-Cont)) � � NOTIFY � 200 OK (NOTIFY)



TSS reference IMS-SS/CC/ Selection criteria PICS 6.3.1/2 AND PICS 6.3.2/24 Test Purpose name CCBS request unsuccessful 480 Temporarily Unavailable is received Test Purpose Ensure that on receipt of a 480 Temporarily Unavailable final response upon CCBS was

requested, an M3UA SCCP TC-End CCBS REQUEST (Return error) component containing the ShortTermDenial Element is sent.

TCAP Parameter values TC-End CCBS REQUEST (Return error) ShortTermDenial



DATA (SCCP (TC-Begin)) � � SUBCRIBE DATA (SCCP (TC-End)) � � 480 Temporarily Unavailable


ETSI

ETSI TS 101 572-2 V1.2.1 (2014-07)336


TSS reference IMS-SS/CC/ Selection criteria PICS 6.3.1/2 AND PICS 6.3.2/24 Test Purpose name CCNR request unsuccessful 480 Temporarily Unavailable is received Test Purpose Ensure that on receipt of a 480 Temporarily Unavailable final response upon CCNR was

requested, an M3UA SCCP TC-End CCNR REQUEST (Return error) component containing the ShortTermDenial Element is sent.

TCAP Parameter values TC-End CCNR REQUEST (Return error) ShortTermDenial



DATA (SCCP (TC-Begin)) � � SUBCRIBE DATA (SCCP (TC-End)) � � 480 Temporarily Unavailable



TSS reference IMS-SS/CC/ Selection criteria PICS 6.3.1/2 AND PICS 6.3.2/24 Test Purpose name CCBS request unsuccessful 403 Forbidden is received Test Purpose Ensure that on receipt of a 403 Forbidden final response upon CCBS was requested, an

M3UA SCCP TC-End CCBS REQUEST (Return error) component containing the LongTermDenial Element is sent.

TCAP Parameter values TC-End CCBS REQUEST (Return error) LongTermDenial



DATA (SCCP (TC-Begin)) � � SUBCRIBE DATA (SCCP (TC-End)) � � 403 Forbidden



TSS reference IMS-SS/CC/ Selection criteria PICS 6.3.1/2 AND PICS 6.3.2/24 Test Purpose name CCNR request unsuccessful 403 Forbidden is sent Test Purpose Ensure that on receipt of a 403 Forbidden final response upon CCNR was requested, an

M3UA SCCP TC-End CCNR REQUEST (Return error) component containing the LongTermDenial Element is sent.

TCAP Parameter values TC-End CCNR REQUEST (Return error) LongTermDenial



DATA (SCCP (TC-Begin)) � � SUBCRIBE DATA (SCCP (TC-End)) � � 403 Forbidden


ETSI

ETSI TS 101 572-2 V1.2.1 (2014-07)337


TSS reference IMS-SS/CC/ Selection criteria PICS 6.3.1/2 AND PICS 6.3.2/24 Test Purpose name CCBS invoked. NOTIFY with State header field set to "terminated" received TC-End is sent Test Purpose Ensure that on receipt of a NOTIFY request the Subscription-State header is set to

'terminated' and the subexp-params reason set to 'noresource' upon CCBS was successfully invoked, an M3UA SCCP TC-End message is sent containing the CCBS CANCEL component.


SIP Parameter values NOTIFY: <Request URI> Event:call-completion Subscription-State: terminated; reason=noresource


CCBS request successfully invoked DATA (SCCP (TC-End)) � � NOTIFY � 200 OK NOTIFY



TSS reference IMS-SS/CC/ Selection criteria PICS 6.3.1/2 AND PICS 6.3.2/24 Test Purpose name CCNR invoked at the O-MGCF NOTIFY with State header field set to "terminated" received

TC-End is sent Test Purpose Ensure that on receipt of a NOTIFY request the Subscription-State header is set to

'terminated' and the subexp-params reason set to 'noresource' upon CCNR was successfully invoked, an M3UA SCCP TC-End message is sent containing the CCBS CANCEL component.


SIP Parameter values NOTIFY: <Request URI> Event:call-completion Subscription-State: terminated; reason=noresource


CCNR request successfully invoked DATA (SCCP (TC-End)) � � NOTIFY � 200 OK NOTIFY



TSS reference IMS-SS/CC/ Selection criteria PICS 6.3.1/2 AND PICS 6.3.2/24 Test Purpose name Interworking of Remote user free indication at the O-MGCF Test Purpose Ensure that on receipt of a NOTIFY request the cc-state body is set to 'ready' upon Call

completion was successfully invoked, an M3UA SCCP TC-Cont message is sent containing the CCBS REMOTE USER FREE component.

TCAP Parameter values TC-Cont CCBS REMOTE USER FREE

SIP Parameter values NOTIFY: Event: call-completion Content-Type: application/call-completion cc-state: ready


CCBS or CCNR request successfully invoked DATA (SCCP (TC-Cont)) � � NOTIFY � 200 OK (NOTIFY)


ETSI

ETSI TS 101 572-2 V1.2.1 (2014-07)338

6.3.9 Communication Waiting (CW)


TSS reference IMS-SS/CW/ Selection criteria PICS 6.3.1/2 AND PICS 6.3.2/8 Test Purpose name Mapping of Generic notification 'call waiting' in a 180 Ringing with encapsulated ACM into

Alert-Info header Test Purpose Ensure that on receipt of a 180 Ringing with encapsulated ACM the Called party status

indicator is set to 'subscriber free' and a Generic notification indicator parameter is present set to ''Call is a waiting call', a 180 Ringing is sent. An Alert-Info header is present and the urn is set to 'urn:alert:service:call-waiting'

ISUP Parameter values ACM: Backward call indicator Called party status indicator Subscriber free Generic notification Call is a waiting call

SIP Parameter values 180: Alert-Info urn:alert:service:call-waiting 180 (ACM): ern not present


INVITE � � INVITE (IAM) 180 Ringing � � 180 Ringing (ACM)



TSS reference IMS-SS/CW/ Selection criteria PICS 6.3.1/2 AND PICS 6.3.2/8 Test Purpose name Mapping of Generic notification 'call waiting' in a 180 Ringing with encapsulated CPG into

Alert-Info header Test Purpose Ensure that on receipt of a 180 Ringing with encapsulated CPG the Event indicator is set

to 'Alerting' and a Generic notification indicator parameter is present set to ''Call is a waiting call', a 180 Ringing is sent. An Alert-Info header is present and the urn is set to 'urn:alert:service:call-waiting'

ISUP Parameter values CPG: Event indicator Alerting Generic notification Call is a waiting call




(ACM) 180 Ringing � � 180 Ringing (CPG)


ETSI

ETSI TS 101 572-2 V1.2.1 (2014-07)339


TSS reference IMS-SS/CW/ Selection criteria PICS 6.3.1/2 AND PICS 6.3.2/8 Test Purpose name Interworking of the Alert-Info header in a 180 into Generic notification 'Call waiting' in a 180

Ringing with encapsulated ACM Test Purpose Ensure that on receipt of a 180 Ringing and an Alert Info header is present the value is set

to 'urn:alert:service:call-waiting', an180 Ringing with encapsulated ACM is sent containing a Generic notification indication parameter set to 'Call is a waiting call'

ISUP Parameter values ACM: Backward call indicator Called party status indicator Subscriber free Generic notification Call is a waiting call






TSS reference IMS-SS/CW/ Selection criteria PICS 6.3.1/2 AND PICS 6.3.2/8 Test Purpose name Interworking of the Alert-Info header in a 180 into Generic notification 'Call waiting' in a 180

Ringing with encapsulated CPG Test Purpose Ensure that on receipt of a 180 Ringing and an Alert Info header is present the value is set

to 'urn:alert:service:call-waiting', a 180 Ringing with encapsulated CPG is sent containing a Generic notification indication parameter set to 'Call is a waiting call'. The Event indicator is set to 'Alerting'

ISUP Parameter values CPG: Event indicator Alerting Generic notification Call is a waiting call



INVITE (IAM) � � INVITE � 100 Trying 180 Ringing (ACM) T i/w2 expired CPG � � 180 Ringing Apply post test routine

ETSI

ETSI TS 101 572-2 V1.2.1 (2014-07)340

Annex A (informative): Bibliography

• ETSI TS 102 710-1: "IMS Network Testing (INT); Interworking between the IP Multimedia (IM) Core Network (CN) subsystem and Circuit Switched (CS) networks (Release 8); Part 1: Protocol Implementation Conformance Statement (PICS)".

• Recommendation ITU-T Q.850: "Usage of cause and location in the Digital Subscriber Signalling System No. 1 and the Signalling System No. 7 ISDN user part".

ETSI

ETSI TS 101 572-2 V1.2.1 (2014-07)341

History

Document history

V1.1.1 October 2013 Publication

V1.2.1 July 2014 Publication

ts 101 572-2 - v1.2.1 - core network and interoperability ... · etsi 6 etsi ts 101 572-2 v1.2.1...

Documents