tutorial of wrc 107 for trunnion
DESCRIPTION
wrc 107 trunnionTRANSCRIPT
PROCEDURE OF WRC-107 CALCULATIONS FOR TRUNNIONHorizontal lift
SKETCH
Step 1 Note values from output file of PVElite, as shown below.
Import data from PV elite
Step 2
Step 3 In PV Elite, Click this button -->(To start design of lifting lug)
Step 4
Open PVElite
A new window "COADE CALC" will open, Go to Step 4
Step 4As shown below in sketch
Step 5
Step 6box as indicated below:
Go to 'Analysis'→'Choose Analysis type'→'Legs and Lugs'
A new window will open. Click " +" new Item button
Fill in the data from Datasheet or PVElite output file and select trunnion in "Analysis Type"
Inputs requiredBy program
Step 7A Provide following values for calculating Axial Load, Normal Load, Tangential Load.
Weight of Empty Vessel (From Step 1 and convert it into Newtons) W = 15000 N
No. of Trunnions n = 2
Load Per Trunnion W / n = 7500 N
FOR HORIZONTAL LIFT ORIENTATIONAxial Load, 5% of (W / n) = 375 NNormal Load W / n = 7500 NTangential Load 5% of (W / n) = 375 N
Step 7B
calculation as indicated in the figure below:
Figure shown below helps selecting Dimension of trunnion
Now click ">>" button as indcated above. New window "Dialog" will open. Fill in the
specifications for trunnion (as calculated in Step 7A) and check in the box for WRC 107
Step 8
Step 9
Step 10
Step 11
Step 12
Click OK in dialog window, click Load and fill in the vessel empty weight (from Step 1) and occasional load factor.As shown below:
Now Save your program by clicking →
Analyze your program by clicking →
Read at the end of Report.
If the results are "Fail. Go to Step 7B & try with different geometrical dimensions.
Unless you get Passed message.
Page 6 of 10
File name:document.xls
PROCEDURE OF WRC-107 CALCULATIONS FOR TRUNNIONVertical lift
SKETCH
Step 1 Note values from output file of PVElite, as shown below.
Import data from PV elite
Step 2
Step 3 In PV Elite, Click this button -->(To start design of lifting lug)
Step 4
Open PVElite
A new window "COADE CALC" will open, Go to Step 4
Page 7 of 10
File name:document.xls
Step 4As shown below in sketch
Step 5
Step 6as indicated below:
Go to 'Analysis'→'Choose Analysis type'→'Legs and Lugs'
A new window will open. Click " +" new Item button
Fill in the data from Datasheet or PVElite output file and select trunnion in "Analysis Type" box
Page 8 of 10
File name:document.xls
Input required
By Program
Step 7A Provide following values for calculating Axial Load, Normal Load, Tangential Load.
Weight of Empty Vessel (From Step 1 and convert it into Newtons) W = 15000 N
No. of Trunnions n = 2
Load Per Trunnion W / n = 7500 N
FOR VERTICAL LIFT ORIENTATIONAxial Load, W / n = 7500 NNormal Load 5% of (W / n) = 375 NTangential Load 5% of (W / n) = 375 N
Step 7B
calculation as indicated in the figure below:
Figure shown below helps selecting Dimension of trunnion
Now click ">>" button as indcated above. New window "Dialog" will open. Fill in the
specifications for trunnion (as calculated in Step 7A) and check in the box for WRC 107
Page 9 of 10
File name:document.xls
Step 8
Step 9
Step 10
Click OK in dialog window, click Load and fill in the vessel empty weight (from Step 1) and occasional load factor as shown below:
Now Save your program by clicking →
Analyze your program by clicking →
Page 10 of 10
File name:document.xls
Step 11
STEP 12
Read at the end of Report.
If the results are Fail. Go to Step 7B & try with different geometric dimensions.Unless you get passed.