tvl 2 installation instructions (1)
TRANSCRIPT
-
7/25/2019 Tvl 2 Installation Instructions (1)
1/11
TVL-2 TV LIFT INSTUCTION MANUAL.
The Pop-up TV Co TV Lift system, is specifically designed for easy installation into
cabinetry, AV rooms, meeting rooms, or any type of application where automatic liftingof equipment is required.
The Lift Column, model TVL-2 is a telescoping type column madewith prefabricated, inter-fitting solid steel tubes, with an internal 24VDC motor-gear box.
The TVL-2 Lift has a maximum load capacity of 80kg,
which is sufficient to lift up to 70 inch LCD & Plasma TVs on the market today.
The new TVL-2 Lift is equally suitable to be inverted, and thus ideal for ceiling
drop down applications. The installation and set up of the system is extremely easy. Only four
screws are required to attach the lifting column to the cabinet wall panel/sub structure.
The electrical connections between all the main parts including Lift Column,Control Box, Switch Box and IR receiver are plug types, which promote
easy installation. Each TV Lift system is equipped
with an IR remote control, and corded handset. If the IR system fails, or is missing or lost, (IR handset)the corded handset provides a backup to maintain operation of the lift.
The control box, with a built in micro-processor, provides the basic
operational functions of Up/Down/Store/Recall. The self-protectionfeature continuously monitors the electrical current consumption of the
motor, and will abort the operation immediately if an abnormal rise in theelectrical current is detected.
The control box is CE and UL approved, and as such is compliant with all the necessary safetyrequirements.
The accessories used to attach the LCD or Plasma TV to the lifting column are included, andare very simple and easily adaptable so that most LCD & Plasma TVs can be used
with this TV Lift system. The bottom and top heights of the lifting column can be modified, then memorized
electronically using the corded handsets set button. The top height of the lift can also be memorizedusing the IR handset (M button)
-
7/25/2019 Tvl 2 Installation Instructions (1)
2/11
TV Lift Mechanism DimensionsModel Number Retracted
LengthStroke length Mounting hole
distanceLoad Speed full
stroke
TVL-2 (Large Stroke) 795 mm 914 mm 650mm 80kg 25sec
TV Lift M chanism Dim nsions
V Lift M chanism Dim nsions
Model number Retracted length Stroke length Mounting hole distance Speed full stroke
TVL-2 (Large stroke) 795mm 914mm 650mm 80kg 25sec
Model number Retracted length Stroke length Mounting hole distance Load Speed full stroke
TVL-2 (Large stroke) 795mm 914mm 650mm 80kg 25sec
TVL-2 (Medium stroke) 693mm 780mm 542mm 80kg 21sec
-
7/25/2019 Tvl 2 Installation Instructions (1)
3/11
Control Box
Hand controller box
IR Receiver
-
7/25/2019 Tvl 2 Installation Instructions (1)
4/11
Mounting Bracket
TV Mounting Bracket
BRACKET LENGTH B/L
TV-2 LARGE 30"
TV-2 MEDIUM 26"
-
7/25/2019 Tvl 2 Installation Instructions (1)
5/11
Parts List.
-
7/25/2019 Tvl 2 Installation Instructions (1)
6/11
Installation Instructions
Note: Most TVs come with their own Mounting screws already screwed into the back of the TV,
or loose in the TV Box. Use those screws instead where possible to ensure youm use the correct
screw size. The screws used in this Kit are M8 screws that may or may not fit your TV. In
addition you may need to open up the screw hole in part 8 using a drill to make the hole larger if
your TVs screws are larger than M8
-
7/25/2019 Tvl 2 Installation Instructions (1)
7/11
-
7/25/2019 Tvl 2 Installation Instructions (1)
8/11
Connecting the TV Lift
Caution:
1. Do not plug into the mains until all the parts are connected.
2.Do not open the control box, otherwise an electrical hazard may occur.
3.Before operating be sure that there are no objects in the path of the TV lift, both above the TVand below or damage to your TV and or the TV Lift may occur.
4.For safety reasons, before operation be sure there are not children or pets close to the TV lift.
-
7/25/2019 Tvl 2 Installation Instructions (1)
9/11
OPERATE BY CORDED HANDSET.
1. Before operating, be sure the "SET" switch stays at normal side, not
"SET" side.
2.Press and hold the "UP" switch, the Lifting column will go upward
continuously.
3.Press and hold the "DOWN" switch, the Lifting column will go
downward continuously.
4.When lifting column is moving, release the switch at any time to stop
movement of the TVL-2 lifting column.
5. Move the TV LIFT up to the position you want it to start (lower limit)
then press the "SET" button at the same time as the DOWN button for
at least 5 seconds, until the LED of the IR Receiver flashes 3 times, then
release the DOWN button and switch the SET button back to the
normal side, not SET side. The lower limit of the lift is now
memorized.
6. Move the TV LIFT up to the most upper position you , (upper limit)
then press the "SET" button at the same time as the UP button for at
least 5 seconds, until the LED of the IR Receiver flashes 3 times, then release the UP button
and switch the SET button back to the normal side, not SET side. The upper limit of the liftis now memorized.
To operate the TV lift once the lower and upper limits have been set, you simply press the up
button on the IR remote handset, and the TV LIFT will go the upper pre-set position. To make
the TV retract to the lower pre-set position simply press the down button on the IR remote
handset and the lift will retract, and automatically stop when it reaches the lower limit. You do
not need to hold the UP or DOWN (using the IR handset) buttons for normal movementonce the limits are set, just press the button once. (known as latch function)
-
7/25/2019 Tvl 2 Installation Instructions (1)
10/11
OPERATION BY INFRA RED REMOTE CONTROL.
1. When operating the IR remote control, it must be pointed to the IR
receiver, at a distance of up to 15 feet max.
2. Press "UP" button, the Lifting column will go upward continuously.
3. Press "DOWN" button, the Lifting column will go downward continuously.
4. When lifting column is moving, pressing any button to stop the movement.
TO SET THE UPPER LIMIT, USING THE IR HANDSET.
1. Move the TV LIFT upwards (upper limit) to the position you want it to stop at, then press the
"M" (on the IR handset) button for 5 seconds, until the LED of the IR Receiver flashes 3 timesThe height of the lifting column is now memorized.
2. After the memory has been set, use the M button to lift the TV LIFT to this memorized
position, note however that pressing the UP button on the IR handset will move the lifting
column to the pre-set upper limit recorded by the corded handset.
NOTE.
The TVL-2 TV lifting column is designed for 10% usage. In other words if the lift is used
continuously for one minute, it is advised for the longevity of the appliance to refrain for further
usage for at least nine minutes.
May we at The Pop Up Tv Co take this opportunity
to thank you for purchasing your new TVL-2 TV
Lift, and we wish you many years of use.
-
7/25/2019 Tvl 2 Installation Instructions (1)
11/11