tyco safety products ©, april, 2006 rev c sensormatic technical training 1 ultramax...

11Tyco Safety Products Tyco Safety Products ©, April, ©, April, 2006 Rev C2006 Rev C Sensormatic Technical TrainingSensormatic Technical Training

Ultra•Max Acousto-Magnetic TechnologyUltra•Max Acousto-Magnetic Technology

EElectronic lectronic AArticle rticle SSurveillanceurveillance

AMS-9040 AMS-9040 UUltra ltra CControllerontrollerAMS-9040 AMS-9040 UUltra ltra CControllerontroller

Revised April, 2006Rev. C

22Sensormatic Technical TrainingSensormatic Technical TrainingRevision C , April, 2006Revision C , April, 2006

Training OverviewTraining Overview

Goal

The Goal of this training is to provide the service technician with the necessary skills to install, configure, and adjust the AMS-9040 system so that it performs to a level expected by the customer.

Products

This training Includes the AMS-9040 controller, associated system detectors, and the Service Configurator program.


Training OverviewTraining Overview

Description

This course consists of a combination of lecture, demonstration, and follow on lab with an estimated length of 5-6 hours.

Prerequisite

Prior Ultra•Max EAS experience ADS-216 Controller or AMS-9030 Controller


Training Objectives (cont.)Training Objectives (cont.)

Upon completion of this training, using the service documentation, you should be able to:

1. Describe the major components that make up an AMS-9040 EAS System.

2. Identify and describe the various types of antennas and pedestals that can be used by the AMS-9040 controller.

3. Describe the capabilities and limitations of any supported system configuration.

4. Locate and describe the function of each connector in the AMS-9040 Controller.

5. Install the AMS-9040 controller and make all necessary connections to power source, antennas, and alarm units.


Training ObjectivesTraining Objectives

6. Using the ADS4 configurator, configure the 9040 controller to operate with any supported pedestal and antenna combinations.

7. Resonate transmitters and set adjustment for proper current.

8. Using the ADS4 configurator, monitor environment noise and configure and adjust receivers for best possible performance.

9. Download voice files to the antennas or to the Digital Remote alarm unit.

10. Using the ADS4 configurator, identify phasing issues and adjust phasing if necessary.

11. Using the ADS4 configurator, isolate a hardware malfunction to a replaceable component.

12. Update controller and antenna firmware when necessary.


IntroductionIntroduction

AMS-9040 Controller is the latest generation, 4-AMS-9040 Controller is the latest generation, 4-channel design. channel design.

1.1. New electronics will expand the number of digital New electronics will expand the number of digital antennas that can be connected to a single controller to antennas that can be connected to a single controller to four. four.

2.2. Worldwide compatible*Worldwide compatible*

3.3. Replaces today’s two-controller configurations with a Replaces today’s two-controller configurations with a single controller (at a comparable cost).single controller (at a comparable cost).

4.4. Move some antenna unique electronics from the controller Move some antenna unique electronics from the controller to the antenna capacitor boto the antenna capacitor boards (reduces controller cost). ards (reduces controller cost).

* Note - with some restrictions in certain countries* Note - with some restrictions in certain countries



Supported Antennas

Digital ProMax IV Digital FloorMax IV Digital DoorMax IV Digital Euro ProMax IV AMS-3000 Loop AMS-3003 Extended Loop AMS-3010 Wide Exit Loop

(9040 Loops are non European only)

Auxiliary Receivers Ranger SkyMax Mullion mount

Antennas Not Supported

EuroMax Plus ProMax Plus FloorMax (old) FloorMax Plus UltraPost Secondary


IntroductionIntroduction Design Features

Drive up to 4 XCVR Antennas Drive up to 4 Aux Receivers/Noise canceling antennas Drive up to two Remote Alarms Drive up to two Beacon Lamps Conduit Ready Single Printed Circuit Board (PCB) RS-485 interface RS-232 Service Port New antenna / peripheral architecture New Digital Signal Processor (DSP) chip (TI), higher integration

of DSP/receiver electronics Configurator Required for Installation (New Configurator) Similar in size and weight than the ADS-216 controller The four transmitter channels can be multiplexed to eight

antenna coils (typically four pedestals).



Digital Antennas

Same antennas with new capacitor tuning boards

Each antenna now has an address selection switch which identifies its unique address

The alarm circuits are driven from the pedestal

Remaining Functions are the same as the D216 antennas

Assisted Transmitter Tuning

Service port at antennas

Antenna ID (Identifies Cap Board Type)

Key Switch to control the Alarms and the Tx



New Capacitor Board Advantages

Independent alarm control of antennas Zone Identification now possibleZone Identification now possible

Supports different message per pedestal

Software on antennas now flash upgradeable

Higher noise immunity & higher data rates

Longer alarm messages with higher dynamic range

Note - New pedestal is incompatible with existing digital antennas Capacitor Board.


AMS-9040 System and Peripheral Networks

NetworksNetworks

System Network

PeripheralNetwork

RS485 to RS232 converter to Modem(BB Electronics Model #485SD9TB)

OrRS485 to Ethernet converter for Networking

(Lantronix Model #UDS10 converter)

RS-485RS-485


Mechanical DescriptionMechanical Description

9040 Chassis Assembly

J2: RS232/ Laptop interface

J5: Sync Link

DS1: Status LED/Heartbeat

AC Power Switch

Rocker Switch orOptional Key Switch

Conduit openings for AC Power

Cable Housing / Mounting Bracket

Single Printed Circuit Board (PCB)


AC Input/EMI Filter

Tx Current Sense & Sequencer

DSP /ReceiverCircuits

Low Voltage Supply

Transmitter Power Ampsand High Voltage Supply

Mechanical DescriptionMechanical Description PCB: Major Functional Blocks


9040 Controller Connectors


4 Tx/Rx PortsAntenna Comm

Ports4 Receive-Only

Aux Ports

P1 P24 P4 P35 Aux A C P5 P25 P6 P36 Comm port connections should correspond to TX/RX connections (A-A, B-B etc).

PCB Connectors

A B C D A B C D

B D


Fan

P3: AC Input

P13: Fan Conn.

J2: RS232 (Laptop interface)

J5: Sync Link

DS1: Status LED/Heartbeat

P41 UltraLink Power (1) ….P7 Remote Alarms (2) P10 Beacon Lamps (2)

The 9040 can power no more than 2 remote alarms, 2 beacon lamps and 1 Ultra Link.

P8: RS485

P26: Pedestal Inhibit

P9: Relays 1 & 2

P12: Relays 3 & 4

P2: Wired Sync

PCB (cont.)




9040 Controller Description9040 Controller Description

9040 Transmitters

- Simultaneous Transmit of Two Antennas (4 Coils)

- Antennas A & C are multiplexed and Antennas B & D are multiplexed. (Similar to M4K)

- 2 AntennasAntennas A and B will

transmit simultaneously

- 4 AntennasAntennas A and B will

transmit simultaneously, then antennas C and D will transmit simultaneously

- 3 AntennasA and B transmit

simultaneously, thenB and C will transmitsimultaneously



9040 Receivers: The 9040 has eight Rx Channels

In normal Rx Configuration (phase flipping), one pedestal utilizes one Rx Channel.

If “nulling” or “coil 1-2” configuration is selected, the pedestal will utilize two Rx Channels.

Therefore, if you have Aux receivers or noise canceling coils associated with Pedestals A and B, you will want to connect the Rx-only antennas to Aux C and/or Aux D, rather than to Aux A and/or Aux B

If you use Aux A and B, It functions, but the system will be slowed down


InstallationInstallation

Installation Steps

1. Install Controller

2. Install Antennas

3. Install Alarm Units

4. Make Connections

5. Set Antenna Addresses (New Step)

6. Configure (Zone Mapping) (New Step)

7. Tuning and Testing



Installing Controller

Remove Top Cover and Cable Tray/Mounting Bracketfrom Controller

Cable Tray/mounting bracket Controller

Top Cover



Installing Controller (cont.)

1. Remove knockouts closest to connectors they are associated with

- Class 2 Dry for Remote Alarms- Class 2 Dry for Remote Alarms

- Class 2 Wet for Alarm- Class 2 Wet for AlarmManagement deviceManagement device

- Class 3 for Antennas- Class 3 for Antennas

2. Attach Conduit and/or Cables

Cable Tray / Mounting Bracket




3. Mount Cable tray/mounting bracket to:

- Wall- Wall

- Ceiling- Ceiling

- Shelf- Shelf

Wall Ceiling Shelf




Wall Mounting

Warning - Mounting Bracket can only be mounted facing up or with cable entry to the left, as shown.

OK Not OK




4. Mount Controller partially onto the mounting bracket, route cables through rectangular opening in the controller housing, attach connectors, and plug connectors into board.




4. Hardwire AC Cable or attach Power Cord




4. Slide Controller completely onto the mounting bracket and secure the two 1/4 turn fasteners


Wiring DiagramWiring Diagram


Installing Digital 4 AntennasInstalling Digital 4 Antennas Connect Tx/Rx cables to Power Pack

Install Romex-Type connectors or conduit fittings in knockouts

Route each Tx/Rx cable through knockout (locations on bracket)

Plug into appropriate TXRX connector on controller board(This connection determines which antenna is which (A,B,C,D) and also sets the address requirements for each cap board. (0,1,2,3))

P1 P24 P4 P35TXRX A TXRX B TXRXC RXRX D

Antenna ACap Board

Antenna BCap Board

Antenna CCap Board

Antenna DCap Board

9040Controller Board


Connecting Conduit and CablesConnecting Conduit and Cables

Connect Com cables to Power Pack

Route each Com cable through knockout

Using a small screwdriver, attach Connectors 2109-0510-10 to each Com cable following the color coded label.

AMS-9040 Controller

COM A COM B COM C COM D

RS485

P2 P12 P9 P26

P5 P25 P6 P36 P8

Wired Sync Relay 3 & 4 Relay 1 & 2 PED Inh.



Antenna Addressing

The antenna addresses range from 0 to 7.

The antenna cap board address must be set to match the connector that its attached to.

Ex. The cap board that is attached TX/RX A, must be set to address 0

Duplicate address are not allowed

The 9040 can support up to eight addressable antennas

If more than four are used, two Comm Cables can be terminated to a single Comm port.


DoorMax and Euro ProMax Cap Board DoorMax and Euro ProMax Cap Board

Assisted Tuning is like D216, except only one coil is tuned at a time

If DS1 and DS2 are on, set JW1-5 to correspond to Tuning LEDs then Press Button

If DS1 and DS3 are on, set JW6-10 to correspond to Tuning LEDs then press button

Repeat until Tx Off LED remains off


FloorMax Cap Board FloorMax Cap Board

Assisted Tuning is like D216, except only one coil is tuned at a time

If DS1 and DS2 are on, set Left Bank jumpers to correspond to Tuning LEDs then Press Button

If DS1 and DS3 are on, set Right Bank jumpers to correspond to Tuning LEDs then press button

Repeat until Tx Off LED remains off


ProMax Cap Board DescriptionProMax Cap Board Description

Assisted Tuning is like D216, except only one coil is tuned at a time If DS1 and DS2 are on, set Bottom coil jumper to correspond to Tuning LEDs then Press

Button If DS1 and DS3 are on, set Top coil jumpers to correspond to Tuning LEDs then press button Repeat until Tx Off LED remains off


Installing Digital 4 PedestalsInstalling Digital 4 Pedestals For each pedestal, connect the Tx/Rx (4-conductor) and Com (9-conductor) cables to the capacitor board.

– Using a small screwdriver, attach the TX/Rx cable to connector 2109-0254-04 according to the following: Pin 1-Black Pin2-Red Pin 3-Green Pin 4-White Pin 5-Shield

– Insert connector 2109-0254-04 into pluggable terminal block P1 on the capacitor board

Tx/Rx

P1


Installing Digital 4 PedestalsInstalling Digital 4 Pedestals

Using a small screwdriver, attach the Com cable to connector 2109-0510-10 following the color-coded label:

Pin 1-Black Pin 2-Brown Pin 3-Red Pin 4-Orange Pin 5-Yellow Pin 6-Green Pin7-Blue Pin 8-Violet Pin 9-Gray Pin 10-Shield

Insert connector 2109-0510-01 into P6 on Cap board

P6Com Cable


Connecting Conduit and CablesConnecting Conduit and Cables

Set Antenna Addresses

Ped A Cap Board to 0

Ped B Cap Board to 1

Ped C Cap Board to 2

Ped D Cap Board to 3

Selectable from 0 to 7On Cap Board


Pedestal TuningPedestal Tuning

The antenna is shipped with the jumpers set to default settings that are acceptable for most installations. However, the antenna may require tuning to adjust for conditions at the installation site.

To tune the pedestal, do the following:

Turn off power pack

Make sure P10(in all Digital 4 antennas) is removed when the pedestal connected to AMS-9040 controller

Access the capacitor board in the enclosure

Make sure that the jumpers are set to defaults.



Turn On power pack

Beginning with Antenna A, check the green Tx Off LED on the capacitor board for each antenna.

If the green Tx Off LED is off, the antenna is tuned.

If the green Tx Off LED is on, the antenna needs tuning.

The antenna is tuned by changing jumper settings on the capacitor board. The controller assists tuning by lighting LED's to indicate the correct jumper settings.


Pedestal TuningPedestal Tuning Step 1

• When DS2 is on indicates the tuning setting is for the Bottom coil (left bank)

• Set the jumpers JW1-JW7 per the DS4-DS10 respectively

• Next, depress check tuning button


Pedestal TuningPedestal Tuning Step 2

• When DS3 is on indicates the tuning setting is for the Top coil (right bank)

• Set the jumpers JW8-JW14 per the DS4-DS10 respectively

• Next, depress check tuning button

Repeat Step 1 and 2 Until DS1 is off



Change the jumpers on the capacitor board to the settings indicated by the yellow LED's on the capacitor board.

If a yellow jumper LED is on, place the corresponding jumper in the “In” (1-2) position.

If a yellow jumper LED is off, place the corresponding jumper in the “Out” (2-3) position.

WARNING—RISK OF ELECTRIC SHOCK! The green Tx Off LED on the capacitor board must be ON before changing jumpers. It indicates there are no high voltages on the board.



Press the check tuning button on the capacitor board and return to previous step and change jumpers again to match LED's

After repeating these two steps several times, the antenna should be After repeating these two steps several times, the antenna should be tuned with all yellow LED's off except DS3 will be flashing one second on tuned with all yellow LED's off except DS3 will be flashing one second on and one second off to indicate normal operation. and one second off to indicate normal operation.

After repeating step 1 and 2 eight times the yellow LED's flash five times, this mean the pedestal did not tuned to the max current and pedestal cannot be tuned. Turn off the power pack and check cable connections and antenna coil connections

Repeat the above tuning procedures to all the antennas


Basic OperationBasic Operation

Detection Processing The detection processing consists of determining whether eight

criteria have passed:

1. Signal-to-noise ratio (diversity combined tag signals exceeds the threshold)

2. Frequency Mean

3. Frequency Range

4. Demod. Amp

5. Demod. Phase

6. Q Amp

7. Q Phase

8. SNR Noncoh.

If all of these conditions have been met, the alarm is activated.


Basic OperationBasic Operation

Transmitter / Receiver Sequence (1 time slot)


Basic Theory of OperationBasic Theory of Operation Decision Sequence - No more Validation state - Performs Continuous Validation

TX

TX

TX

TXOFF

TX

TX

TX

Receiver

Tag & Noise AmplitudesTag Frequency

Detector

Receiver Receiver Receiver Receiver Receiver Receiver

7 time slots = 1 frame

Rx Signal

(Random)

Alarm Signal


Installation ConsiderationsInstallation Considerations

EuropeanEuropean Applications, Applications,

Click here Click here

Non-EuropeanNon-European Applications, Applications,

Continue with next slideContinue with next slide


ConfigurationsConfigurations

The following configurations and restrictions The following configurations and restrictions are for are for Non-European applicationsNon-European applications only only


Application RequirementsApplication Requirements

Pedestals Transmitters operate at 16 amps, Phase Flipping

Pedestals A and B firing simultaneous-alternatingPedestals A and B firing simultaneous-alternating Pedestals C and D firing simultaneous-alternatingPedestals C and D firing simultaneous-alternating

FloorMax Antennas Transmitters operate at 16 amps, Phase Flipping

Antennas must be installed so that adjacent antennas do not fire simultaneously

The installed order of the antennas across the exit must be: A - C for two antennasA - C for two antennas A - C - B for three antennasA - C - B for three antennas A - C - B - D for four antennasA - C - B - D for four antennas


Application RequirementsApplication Requirements

Loop Antennas

Systems have transmitter current limitations.

Refer to the antenna installation guides.


Example ConfigurationsExample Configurations

Dual (1or 2 Zones)

Split (1, 2, or 3 Zones)

Tx/Rx A

Tx/Rx B

Zone 1

Door 1

Tx/Rx A

Tx/Rx BTx/Rx C

Zone 1

Zone 2

Door 1

Dual Split


Quad (1, 2, 3, or 4 Zones)


Tx/Rx ATx/Rx B

Tx/Rx CTx/Rx D

Zone 1Zone 2

Zone 3

Door 1


Twin Exit Dual


Tx/Rx ATx/Rx B

Tx/Rx CTx/Rx D

Zone 1

Zone 2

Door 1

Door 2


Single FloorMax


Tx/Rx A

Zone1

Door 1


Dual and Split FloorMax


Installed Order A - C Installed Order A - C - B


Quad - FloorMax Installed order: A - C - B - D



Split Combo (single floormax)


Zone 1

Door 1

Tx/Rx ATx/Rx B

Tx/Rx C


Dual Split Center pedestals are Receive-only

Aux C with Pedestals A and B Aux A with Pedestals C and D


Door 1

Door 2

Zone1 Zone2Zone3 Zone4


Click here Click here To skip over the To skip over the

European configurations slidesEuropean configurations slides


European ConfigurationsEuropean Configurations

The Following slides are forThe Following slides are for

European configurations onlyEuropean configurations only


European ConfigurationsEuropean ConfigurationsEuropean ConfigurationsEuropean Configurations

Pedestals

Transmitters are limited to 12Amps

Must Transmit in Fig-8 only.

ProMaxProMax

DoorMaxDoorMax

Euro ProMaxEuro ProMax

European use of the configurator will automatically set the transmitters to the European current and polarity settings.

“European Use”

Running configurator with computer having European version of any Windows operating system


European ConfigurationsEuropean ConfigurationsEuropean ConfigurationsEuropean Configurations

FloorMax Antennas Horizontal in-Floor use only

One to four Antennas (A, B, C, and D)

Transmitters Operate at 16Amps.

Adjacent Antennas that fire simultaneously must be wired with opposing polarities

Must swap wires at controller TXRX connector (Antennas B and D)Must swap wires at controller TXRX connector (Antennas B and D)– Red and Black– Green and White

European use of the configurator will set the transmitters to the European current and polarity settings.

TxRx B

TxRx A


Pedestals - Dual (1 or 2 Zones) - Split (1, 2, or 3 Zones)


Tx/Rx A

Tx/Rx B

Zone 1

Door 1

Tx/Rx A

Tx/Rx BTx/Rx C

Zone 1

Zone 2

Door 1

Dual Split


Pedestals – Quad (1, 2, 3, or 4 Zones)


Tx/Rx ATx/Rx B

Tx/Rx CTx/Rx D

Zone 1Zone 2

Zone 3

Door 1

Quad System with 3 Zones


Pedestals - Twin Exit Dual


Tx/Rx ATx/Rx B

Tx/Rx CTx/Rx D

Zone 1

Zone 2

Door 1

Door 2


Pedestals - Dual Split Center pedestal is Receive-only

Aux C with Pedestals A and B Aux A with Pedestals C and D


Door 1

Door 2

Zone1 Zone2Zone3 Zone4


FloorMax Antennas (1, 2, 3, or 4 antennas allowed)

If the controller sees an odd number of FloorMax antennas, it will fire the transmitter for the odd numbered antenna in Fig-8 configuration only.

Must be installed in sequence (A-D) across exit

To meet regulatory requirements, adjacent antennas must transmit To meet regulatory requirements, adjacent antennas must transmit simultaneously and with apposing polaritiessimultaneously and with apposing polarities

With two Antennas, A and B always fire simultaneously. With two Antennas, A and B always fire simultaneously. – Antennas B must be wired out of phase with A.

With three antennas, A and B fire simultaneously, then C will fire by With three antennas, A and B fire simultaneously, then C will fire by itself, but in Fig-8 onlyitself, but in Fig-8 only

– Antennas B must be wired out of phase with A.

With four antennas, A and B fire simultaneously, then C and D fire With four antennas, A and B fire simultaneously, then C and D fire simultaneously. simultaneously.

– Antenna B must be wired with opposing polarities to A – Antenna D must be wired with opposing polarities to C



Single – FloorMax

A single antenna will onlyfire in Figure-8 Configuration only.

It will not let you

change it.


Tx/Rx A

Zone1

Door 1

Zone1 = 2.1m maximum


Dual – FloorMax (Can be configured with 1or 2 zones)


Tx/Rx ATx/Rx B

Zone1

Door 1

Antenna B has the Red/Black and Green/White wires swapped at the controller TXRX port (P24)

Zone1 = 4.2m maximum

TxRx B

(P24)

TxRx A

(P1)

Controller PCB


Split – FloorMax (Can be configured with 1, 2, or 3 zones)

Antennas A and B will fire simultaneously

Then, antenna C will fire by itself, but only in Fig-8


Antenna B has the Red/Black and Green/White wires swapped at the controller TXRX port (P24)

TxRx C

(P4)

TxRx B

(P24)

TxRx A

(P1)

Controller PCB

Door 1

Zone 1Zone 2


Antennas B and D have the Red/Black and Green/White wires swapped at the controller TXRX ports

Tx/Rx ATx/Rx B

Zone1

Zone2

Door 1

Tx/Rx CTx/Rx D

Quad – FloorMax (Can be configured with 1, 2, 3, or 4 zones)


TxRx D

(P35)

TxRx C

(P4)

TxRx B

(P24)

TxRx A

(P1)

Controller PCB


The Following slides apply to all applicationsThe Following slides apply to all applications


ConfiguratorConfigurator

Digital Configurators

ADS - Digital Configurator

Operates:Operates:– Digital 216– AMS-1070 (Maxcalibur)– AMS-9030 Controller

ADS4 – Digital Configurator

OperatesOperates– AMS-9040 Controller– AMS-1080 (Ultra Lane)– AMS-9050

Shortcut ICONs

Digital PlatformCE Configurator

ADS4 CEConfigurator

2.03a



ADS4 CE Configurator

ADS4 Configurator Release 2.03a Help Shows:

Shown is ADS4 Configurator with 9040 Attached



Basic Settings Tabs

3 Tabs only

1. Setup

2. TX Configuration

3. Flash Downloads

No RX Configuration tab (ADS configurator only)

No Diagnostic tab (ADS configurator only)


Configurator ShortcutsConfigurator Shortcuts

Shortcut Icons (Compared to ADS Configurator)

SynchronizationTransmit CurrentZone Mapping

Sequence Table


Setup ScreenSetup Screen

Setup Tab Antenna Inventory

ProMax, DMProMax, DMFM, Aux, FM, Aux, Non IntelligentNon IntelligentAuto DetectionAuto DetectionEuropean SystemEuropean System

Temperature Ambient temperature Ambient temperature

in pack in pack Warnings when Warnings when

approaching yellow approaching yellow and red zonesand red zones

Alarm Controls LampsLamps AudioAudio RelaysRelays Jammer TriggerJammer Trigger Remote AlarmsRemote Alarms Beacon AlarmsBeacon Alarms

European System or Not European System


Configuring SystemConfiguring System

Setup Screen

Displays Inventory of Connected Antennas Initially comes up with “Auto Detection” on

Zone Mapping

Defines Doorways and Zones (configuration) System builds default “Zone Mapping” Screen (If Auto Detection on)

Zone Mapping Screen

This is a Drag-and-Drop screen (from inventory to doorway/zones

Configure Doorways and Zones as desired Save configuration to pack Changes unchecks “Auto Detection” on the setup screen


Zone MappingZone Mapping

Default Mapping for two ProMax pedestals

Inventory from Setup Tab is placed in Unassigned antennas

Controller powered up with “Auto Detection” checked

If a Tag is detected in Zone 1, only Zone 1 alarms will activate.

If a Tag is detected in Zone 2, only Zone 2 alarms will activate.


Zone MappingZone Mapping Re-Mapped for Doorway for One Zone

To change from default, drag Zone 2 back to unassigned area

Drag Ant B intoZone1

Or Clear map under

“settings”drop down.

Drag Door 1 over Drag Zone 1 over Drag Ant A to

Zone 1 Drag Ant B to

Zone 1 Drag Alarms

All alarms are activated for any detected tag

Detection at either Pedestal Activates All Alarms


Zone MappingZone Mapping

Write Configuration to Controller

This changes“Auto Detection”to Uncheckedstate onsetup screen

If auto detectionis checked and the power is cycled, the mapping will return to default

Your mapping will be lost


Zone PropertiesZone Properties

Double-Click on a “Zone” or “Alarm:”

Clear Alarm Count Zero Count in Zero Count in pedestal and herepedestal and here

Backfield Mode Changes Zone to Changes Zone to

Alternating Receive Alternating Receive and Transmitand Transmit

View change in View change in sequence screensequence screen

Alarm Counters Maps zone alarms Maps zone alarms

one antenna or one antenna or multiple antennasmultiple antennas

Don’t forget to Write to controller


Zone PropertiesZone Properties

Double-Click on a “Pedestal”

Reduces backfield

Manually set each antenna

Rx only Receive OnlyReceive Only

Tx only Transmit OnlyTransmit Only

XCVR Transceiver Transceiver


Tx Configuration ScreenTx Configuration Screen

Tx Controller Settings Current Amount Enable / Disable

Misc Tx Settings Frequency Control

Low High Nominal Hopping

Polarity Control Aiding Fig 8 Normal (both)

Tx Inhibit Assignments P26 Connector

TX Configuration Screen


Flash Downloads ScreenFlash Downloads Screen

Controller Application

Peripheral Device Application Voice Alarm

Progress

Controller Reset

Flash Downloads Screen



Resetting Controller and Forcing a Flash Download

Perform the following

1. Turn off power to controller

2. Connect a grounding wire from pin 1 of P18 to TP108 (Gnd).

3. Connect laptop and start configurator

3. Power on the controller. ( It will ask you to select file to download)

4. Remove grounding wire

5. Select file to down load. (Flash download starts automatically)

TP108 P18, Pin 1TP108 P18, Pin 1GroundGround

9040 Printed Circuit Board



Peripheral Devices None Ant A Ant B

Remote/Alarm 0 All Antenna

Flash Type

Application

Voice alarm

Play Voice Alarm

Peripheral Device Download


System Noise Average screenSystem Noise Average screen

Displays the tag window and noise average window data

One Screen for each Doorway

Avg. Noise Tag Threshold

Receiver Polarity Aiding Flipping Figure 8 Coil 1-2 Nulling


System Noise Average screenSystem Noise Average screen

(Continued)

Detector Active Tag

Ferrite Tag

Tag Too Close


Individual Noise AveragesIndividual Noise Averages

Detailed look at each antenna Noise Avg. Detection Criteria Polarity All Receivers Receiver Controls

Ringdown Canceller Min Threshold Sensitivity Adj Rx Gain

Enable AGC, Enable AGC, Low Gain,Low Gain,10,20, or 30dB10,20, or 30dB

Notch Sequence Before or afterBefore or after

Ringdown Ringdown CancellerCanceller


Individual Noise AveragesIndividual Noise Averages

Receiver Controls (Continued)

Ringdown Canceller Min Threshold Sensitivity Adj

Rx Gain Enable AGC,

Low Gain,10,20, or 30dB

Notch Sequence Before or after

Ringdown Canceller


Noise Canceling ScreenNoise Canceling Screen

Allows some cancellation of noise sources withthe use of noise coils

Screen will change based on system configuration

Will not work for all types of noise

Noise coils must be placed where they will not see the tag signal

Get screen shot for this


Noise Canceling ScreenNoise Canceling Screen

(cont.)

Antenna Noise Avg

Aux-to-antennaSelection Aux A1 Aux B1 Aux C1 Aux D1 None

Tone Parameters

Get screen shot for this


Frequency AnalyzerFrequency Analyzer

Shows the energy of the Rx signals in the frequency domain

Useful for deciding when to implement advanced techniques such as noise canceling and nulling

Notch Freq

Rx Selection

Controls Guard Band Max. Notch Notch Threshold

Periodic Recall


Time / Phase GraphTime / Phase Graph

Displays the Rx energy information in the time domain

Useful for identifying systems out of phase

Graph is adjusted to include zero crossing delay

First set of DotsRepresent Tag Window

Last set of dotsrepresent NoiseWindow

Dashed line are where remote transmitters should appear (Sync Window)


Error ReportError Report

Report Contains: System Info Runtime info System Errors First Error Log Last Error Log Fatal Error Log


Advanced SettingsAdvanced Settings

Screen can change with different versions of application code.

Clear NVM will reset all settings

back to factory default

Bypass Ped. Tuning

Criteria Relaxation

RDC Threshold

Jammer Sensitivity

Zero Crossing Quality

UltraLink Delay

Corona Sensitivity


Sequence TableSequence Table

Table Length Max of 2

Receiver Sequence Example shows:

All coils receive simultaneously

Transmitter Sequence Example Shows:

Transmitters for bothTransceivers fire Simultaneously (all Coils)


Sequence TableSequence Table

Sequence Example

Backfield Set in Zone Mapping


Diagnostic TestsDiagnostic Tests

Select tests to run by placing a check in the box, then click ongreen arrow

Pass/FailYellow - Yellow - Running Green -Green - Passed Red - Red - Failed


Tx CurrentTx Current

Shows Current for all Transmit Antennas

Used to determine if transmitters need tobe tuned

European System 12 amps Pedestals 16 amps FloorMax

Tx Frequency Low High

Tx Status Displays current

configured Polarity


SynchronizationSynchronization

Line PLL

Tx Sync Auto Sync Sync Link Wired Sync Input Power

Enable Sync Link Output

Wired Sync Output

Auto Sync State

Zero Crossing Delay in mSec

Threshold


Miscellaneous ShortcutsMiscellaneous Shortcuts

Provides Help Information

Refresh screen

Connect using a TCPIP Network

Reset and restart Communications

Displays Packet Monitor

Turns Off Sounds


Packet MonitorPacket Monitor

Displays CommunicationsBetween Laptop and Controller


Help ScreensHelp Screens

Example Info

Help for Setupscreen


HelpHelp

??Don’t forget to use itDon’t forget to use it


Lab ActivityLab Activity

Questions?

tyco safety products ©, april, 2006 rev c sensormatic technical training 1 ultramax...

Documents

controller slide

controller cost

training objectives

single controller

c slide

update controller

controller configurations

introduction ams