ultimate periscope & riser gujoymonkey.com/run/files/periscope-n-riser.pdf · periscope &...
TRANSCRIPT
PERISCOPE & RISER OVERVIEW
INTRODUCTION
PERISCOPE & RISER OVERVIEW
INTRODUCTION
Astromech Droids; they don’t float. Whether you’re broken down in a Dagobahswamp or relaxing on Mon Calamari, water hazards are everywhere. Beprepared for your droids inevitable submergence in liquids (or fine sand) withthe Periscope & Riser from IA Parts!
These finely crafted assemblies are an essential part for any R2 Unit looking tobe prepared for the toughest environments.
Star Wars, R2-D2 and related characters are property of Lucasfilm Ltd. Parts designers and manufacturers are not associated in any waywith Lucasfilm Ltd. Parts shown are supplied exclusively to R2 Builders Club members and are not to be resold or made available tooutside parties. Parts engineered & provided by Michael Wheeler. This document designed & written by Paul Murphy. September 2012.
R2-SERIESPERISCOPE& R I S E RASSEMBLY
R2-SERIESPERISCOPE& R I S E RASSEMBLY
PERISCOPE PARTSPERISCOPE PARTS
Main Housing
Top Insert Side Lenses Front Lens
Rear LED Gaskets
HARDWAREHARDWARE
1 inch Screw 3/4 inch Screw M1 Screws M2 Screws
M2 Washers
2 inch Screw
8mm Washers 3/8 inch Nut
riser PARTSriser PARTS
Cap Boot Shaft Collar
Boot
Boot Disk
Center Shaft Large Clip
Small Clip
Boot Shaft
Large Clip Insert
Shaft C Shaft C Collar Small Clip Insert
STEP 1STEP 1
Place Side Lenses in the round openings. The lenses are heldin position using the M2 Screws and M2 Washers.Then place the Front Lens, securing it in position with the M1Screws. Optionally notch or drill shallow holes into the top ofthe Front Lens to allow the screws a stronger hold.Place the two LED gaskets through the holes in the back ofthe periscope.
Fig.1
Fig.2
STEP 2
Fig.3
Fig.4
Assemble the Center Shaft, Large Clipand Large Clip Insert as shown in Figure 3.Attach the shaft to the periscope with a 1 inch Screw. Remember to rotate the clipso that the insert lines up with the adjacent hole in the periscope.
STEP 2
Find the hole in the periscope forShaft C and place a 1 inch Screwthrough it.Place the Shaft C Collar over thescrew, then the small clip. Thenscrew Shaft C into position asshown in Figure 5.
Fig.5
STEP 3STEP 3
R2-SERIESPERISCOPE& R I S E RASSEMBLY
THAT WAYTHAT WAYTHAT WAYTHAT WAY
R2-SERIESPERISCOPE& R I S E RASSEMBLY
Place the Boot Shaft Collar on thethreaded end of the Boot Shaft,
then screw the Boot Shaft intothe threaded hole of the
periscope (Figure 6).Then place the Boot Diskand Boot in place around
the Boot Shaft.
Fig.7
Fig.8
Fig.9 Fig.10
Fig.6
STEP 4STEP 4
STEP 5
Attach the Cap to Shaft C and Boot Shaftusing the 3/4” Screw and 3/8” Nut on thebottom of the Cap.
STEP 5
ARTOO...ARTOO...
Once the Periscope is installed in your dome and isoperational, you’ll want to attach your dome’s Pie Panelto the Top Insert. This is done by securing the Pie Panelto the Top Insert using some form of epoxy. The Top Insertis then fastened to the periscope using the 2 inch Screw.
Alternatively, disc magnetscan be placed in the holesshown in the Top Insert andMain Housing. This allowsthe pie panel to be attachedwithout the need to accessthe 2 inch Screw.Magnets are McMaster PN5902K44 and #5902K43(4 of each).
2 inch Screw holds the Insertto the periscope housing here
Optionalmagnet
locations
PIE PANEL ATTACHMENTPIE PANEL ATTACHMENT