ultrasonic cleaners - joke · 3 safety instructions joke® instruction manual eco-clean ultrasonic...

Ultrasonic Cleaners Eco-Clean

Instruction Manual

1 List of contents

JOKE® Ins truct ion manua l Eco-Clean u l t rason ic c leaners

2

1 List of contents............................................................................................................... Page 02

2 Tips on using the manual.............................................................................................. Page 03

3 Safety instructions.......................................................................................................... Page 04

4 Warranty ......................................................................................................................... Page 06

5 Device overview ............................................................................................................ Page 07

6 Technical data................................................................................................................. Page 09

7 Operation........................................................................................................................ Page 11

8 Troubleshooting............................................................................................................. 0

9 Care and Maintenance .................................................................................................. Page 21

10 Cleaning products.......................................................................................................... Page 22

11 Telefax form.................................................................................................................... Page 23

2 Tips on using the manual


3

This manual has been written for the device user to ensure a problem-free op-eration, care and maintenance.

Important instructions and information concerning safety and operational reliabil-ity have been highlighted.

The symbols used in the manual have the following meanings:

Working and operating processes which must be observed to the let-ter to exclude any risk to persons.

CAUTION!

IMPORTANT! Working and operating processes which must be observed to the let-ter to avoid any damage to the device.

INFORMATION! Technical information to which the device operator must give special attention.

The illustrations and diagrams are numbered in sequence within each chapter. Some of these illustrations have keys. References to illustrations within the text e. g. (5.1/2) have the following meaning:

5.1 = Figure 5.1

2 = Position 2 in the key to the figure.

Please feel free to call our customer service department at any time should you encounter technical problems which are not dealt with in this manual:

Telephone +49 (0) 22 04 / 8 39 - 0

Telefax +49 (0) 22 04 / 8 39 - 86

INFORMATION! www.joke.de

Spare parts lists and operating manuals for our products are to be found at www.joke.de.

3 Safety Instructions


4

This device has been built according to the latest technical standards and generally ac-

cepted safety regulations. Nevertheless, it can constitute danger to life and limb for op-

erator or third parties and a hazard to the device itself or other equipment during use.

(1) Only use the device if in perfect working order and for its intended pur-

pose. You must always pay attention to the instruction manual and safety

instructions therein and be aware of the risks! Repair any faults which

could affect the device’s safety immediately by yourself or have these re-

paired.

IMPORTANT!

The unit is designed exclusively for cleaning workpieces using the cleaning liquids

recommended by the manufacturer. Any other use will be deemed to be contrary

to its intended purpose. The manufacturer cannot be held liable for any resulting

damages. The risk is borne solely by the user.

Correct use also includes compliance with the instruction manual and an observa-

tion of the care and maintenance conditions.

(2) Keep the instruction manual handy at the device’s place of use.

(3) Pay attention to and observe generally applicable statutory and otherwise binding

regulations relating to accident prevention and environmental protection in addition

to the information provided in the instruction manual!

CAUTION! (4) All personnel commissioned to work on or with the device must have

read this instruction manual, and particularly the safety instructions

chapter, before starting work. This applies especially for personnel who

only work with the device occasionally.

(5) Stop the device immediately should you notice changes to the device or its operat-

ing behaviour that are relevant to its safety. Have these remedied before restarting

work.

(6) Observe the safety instructions on the device and keep them legible.

(7) If changes in the device relevant to safety occur or the operating behaviour is modi-

fied, shut the device down immediately. Have the malfunctions remedied.

(8) Do not carry out any modifications, additions or conversions to the device! This

also applies to the installation and adjustment of safety equipment.

(9) Spare parts must meet the technical requirements specified by the manufacturer.

This can only be guaranteed with original JOKE® spare parts.

3 Safety Instructions


5

(10) Any work on/with the device may only be carried out by qualified, appropri-ately trained and authorised personnel. Pay attention to minimum statutory age limits!

(11) Personnel undergoing training or in a general apprenticeship should only be allowed

to work with the machine under the constant supervision of an experienced opera-

tor!

(12) Restrain from any type of work that could jeopardise your safety.

(13) The device may only be used if all protective and safety equipment is in place and in

proper working order.

(14) Do not leave the device unattended when switched on!

(15) Stop and secure the device immediately in the event of malfunctions! Faults must

remedied at once.

(16) Do not clean live creatures (animals and plants) in the device!

VORSICHT!CAUTION! (17) Do not reach into the ultrasonic bath during the ultrasonic clean-ing!

(18) Cavitation noises are generated during the ultrasonic cleaning.

3 Safety instructions


6

4 Warranty


7

Joisten & Kettenbaum warrant the correct manufacture of every Joisten & Ket-tenbaum product which is delivered in accordance with the terms of contract and delivery.

This warranty does not cover damages caused by normal wear and tear, incor-rect handling, negligent use, the fitting of non-original spare parts, inadequate care and/or a failure to comply with this technical manual.

The device may only be used by appropriately trained personnel. If it is not, all warranty claims will be forfeited according to the terms of de-livery.

IMPORTANT!

5 Device overview

Purpose

The JOKE® ultrasonic cleaners with frequency switching are exclusively intended for cleaning of workpieces with the cleaning liquids recommended by the manu-facturer. The device is particularly suitable for lapped/polished workpieces or ob-jects (devices in the medical, dental, laboratory and optical field, clocks and jewel-lery), in which the smallest cavities or undercuts exist and mechanical cleaning is not successful.

If all the instructions for handling are complied with, ultrasonic cleaning repre-sents an extremely gentle and thorough form of cleaning.

Fig. 5

1 2 3 4

1

2

3

4

5

6

.1 View of contro

5

Timer for ultraoperation (withpermanent sett

Ultrasound outtensive cleaningsoft: for gentle c

Heating switch

Controller for

Ultrasonic cont

Heating contro

JOKE® Ins tEco-Clean u l t

ls

6

sound operatio automatic swing ∞ (manual

put selection s and leaning of sen

heating thermo

rol light indica

l light indicates

ruct ion manua l rason ic c leaners

n. Adjustment oitch-off) switch-off)

witch for 2 clea

sitive parts

stat 20 – 80°C

tes ultrasound o

heating operati

8

ptions: 1-15 min. for short

ning settings. power: for in-

peration

on

5 Device overview


9

Cleaning principle

Ultrasonic transmitters are arranged under the base of the vibration trough, which convert electrical energy into mechanical vibrations.

The cleaning liquid in the trough is excited with 35 KHz and caused to vibrate. At the same time, tiny vacuum bubbles are formed which implode (cavitation) result-ing in pore-deep cleaning of the parts arranged in the cleaning liquid.

Select the desired output setting according to the cleaning intensity required: Soft Gentle cleaning to remove light soiling and for sensitive surfaces.

Power Intensive cleaning for stubborn soiling, in addition to rapid cleaning for robust surfaces.

Sweep

The working frequency is continuously modified within a defined range. As a re-sult, the minima and maxima of the sound field is spatially displaced in the trough. A more even load on the ultrasonic transmitter is also achieved. The cleaning ef-fect is more uniform than in normal operation.

6 Technical data


10

Eco-Clean 30 HA

Eco-Clean 50 HA

Eco-Clean 70 HA

Eco-Clean 140 HA

Max. trough filling volume (litres) 3.0 4.5 6.5 14.0

Trough working volume (litres) 2.0 3.5 5.0 10.0

Trough dimensions W x D x H (mm) 240x130x100 240x130x150 300x150x150 300x240x200

Device external dimensions W x D x H (mm) 360x205x250 360x205x300 360x225x300 425x315x350

Trough / housing material Stainless steel Stainless steel Stainless steel Stainless steel

Drain 3/8“ 3/8“ 3/8“ 1/2“

Weight (kg) 7,1 8,3 9,6 13,2

Basket internal dimensions W x D x H (mm) 216x106x52 216x106x80 276x126x80 276x216x140

Mesh size of basket (mm) 6 6 6 9

Mains voltage (Vac) 115 / 230 115 / 230 115 / 230 115 / 230

Mains frequency (Hz) 50 / 60 50 / 60 50 / 60 50 / 60

Mains connection 1 phase

earthing con-tact

1 phase earthing con-

tact


tact


tact

Power input (W) 540 580 600 1120

Ultrasonic frequency (kHz) 35 35 35 35

Effective ultrasonic output (W) 70 / 120 switchable

100 / 160 switchable



max. HF constant maximum output (W) 240 320 360 600

Heating output (W) 400 400 400 800

Thermostat control range 20-80°C 20-80°C 20-80°C 20-80°C

Permanent sweep function yes yes yes yes

Timer 15 min./constant operation yes yes yes Ja

Order no. 0 668 000 0 668 010 0 668 020 0 668 030

Optional accessories

Stainless steel lid (order no.) 0 668 001 0 668 001 0 668 021 0 668 031

Stainless steel basket (order no.) 0 668 003 0 668 013 0 668 023 0 668 033

6 Technical data

Accessories for the JOKE® Eco-Clean ultrasonic cleaners

1 Stainless steel lid 2 Basket insert, stainless steel mesh Controls of the JOKE® Eco-Clean ultrasonic cleaners


11

7 Operation

Fig. 7

1 2 3 4

1

2

3

4

5

6

.1 Overview of co

5

Timer for ultraoperation (withpermanent sett

Ultrasonic outpsive cleaning ansoft: for gentle c

Heating switch

Controller for

Ultrasonic cont

Heating contro

JOKE® Ins tEco-Clean u l t

ntrols

6

sound operatio automatic swing ∞ (manual

ut selection swd leaning of sen

heating thermo

rol light indica

l light indicates

ruct ion manua l rason ic c leaners

n. Adjustment oitch-off) switch-off)

itch for 2 clean

sitive parts

stat 20 – 80°C

tes ultrasound o

heating operati

12

ptions: 1-15 min. for short

ing settings. power: for inten-

peration

on

7 Operation

Operation for the first time

Before operation for the first time after removing the packaging, check the housing, controls/mains connection cable and the ultrasonic trough for any dam-age.

If damage is observed, the device must not be operated. In this case, inform JOKE® customer service.

1. Place the device on a firm, dry base.

IMPORTANT! It is essential to prevent penetration of moisture on the underside of the device.

Permitted ambient temperature: +5 - +40° C. Permitted relative humidity up to 30° C: 80 % Permitted relative humidity up to 40° C: 50 % Misting is not permitted!

2. Screw/install the elbow and the drainage hose on to the shut-off cock on the side of the device.

IMPORTANT! 3. Fill the vibration trough with cleaning liquid.

Only use cleaning liquid authorised by the manufacturer (JOKE®-Clean).

WARNING! Never fill the device with inflammable liquids or volatile solvents. This results

in a risk of fire and explosion.


13

7 Operation

wrong right

Bild 7.2

IMPORTANT! Fill the vibration trough up to the mark with liquid, but at least to 2/3 how-ever. An excessively low filling level will result in damage to the device.

4. Connect the device to the power source with the mains cable.

The rotary switch for temperature adjustment (7.1/5) must be set to “0” and the switch for the heating must be set to “OFF”.

INFORMATION!

Take care to ensure proper earthing of the socket. IMPORTANT!

5. Arrange the workpieces in the basket insert or in the vibration trough

During each cleaning operation, ensure that the workpiece is completely covered with cleaning liquid.

Cleaning is normally performed directly in the vibration trough.

Indirect cleaning in inserts or a suspension trough is to be performed when:

• Using chemically corrosive cleaning liquids (e.g. acids, etc.)

• Removing chemically corrosive soiling (e.g. cleaning of racks from continuous processors)

• Removing abrasive soiling (e.g. polishing compound, resin and sand).

Cleaning directly in the vibration trough

• Cleaning only with a basket insert or device container.

• The object to be cleaned must not stand on the floor of the trough.


14

7 Operation


15

Fig. 7.3 Indirect cleaning in inserts or in an unperforated suspension trough

• Fill the inserts or suspension trough with cleaning liquid (e.g. water + JOKE® Clean 225 dispensed).

• Suspend the inserts in the perforated lid. Do not stand them on the floor of the trough.

IMPORTANT! Inserts or the suspension trough must be immersed at least 2 cm deep in the cleaning liquid. In doing so, take care to fill the vibration trough 2/3 full. Several inserts with different cleaning liquids can be ultrasonicated simultane-ously.

INFORMATION!

Bild 7.4 Kontaktflüssigkeit = Contact liquid

7 Operation

Further instructions for the insertion of the goods to be cleaned

• Place the more heavily soiled side facing downwards.

• Do not stack parts on top of each other, ultrasound will be absorbed.

• Sensitive parts must not touch each other. Damage is avoided by using the plastic inserts, the plastic insert basket or the silicon nubbed mat in suspension troughs.

• Temperature control for heat-sensitive parts.

• No air bubbles must be present in cavities (e.g. blind holes).

Switching the ultrasonic cleaner on and off

The device is switched on and off by adjusting the timer.

Timer operation

1. Turn the rotary knob (fig. 7.1/1) clockwise to the desired cleaning time (max. 15 minutes).

2. The timer switches off automatically once the preset time is over.

3. The cleaning time can be shortened or the device switched off by turning in the opposite direction.

Constant operation

1. Turn the rotary knob (fig. 7.1/1) to the ∞ position.

2. The device does not switch off automatically; therefore turn the rotary knob back to “OFF” in order to switch off.

INFORMATION! In the switched off state, the device may remain connected to the mains. Disconnection from the mains is performed by pulling out the mains plug.


16

7 Operation


17

Output adjustment

The ultrasonic output can be set to soft or power at the rocker switch (fig. 7.1/2).

The preselected setting is constantly maintained.

Adjustment of the heating

1. Set the rotary selector knob to the desired temperature.

2. Rocker switch in the “ON” position

The white control lamp goes out once the desired temperature is reached.

The heating functions independently from the ultrasound.

IMPORTANT!

INFORMATION! Do not switch on the heating without cleaning liquid. There is a risk of burning out. Warmed cleaning liquid intensifies the cleaning. Do not heat disinfection liquids. Ultarsonic energy also warms the cleaning liquid; consequently, simultaneous ultrasoni-cation reduces the heating time. By constant ultrasonication and covering the vibration trough, the liquid temperature may increase to above the preset value.

INFORMATION!

IMPORTANT!

INFORMATION!

INFORMATION!

7 Operation


18

Heating the cleaning liquid

Depending on the soiling, in addition to the assistance of the suitable cleaning medium, it is recommended to heat the cleaning liquid.

“heating” switch in the “on” position

Switch the heating switch on. The yellow control light “heating” illuminates.

Temp. adjustment at the control thermostat

Set the desired cleaning temperature. The trough must be at least half full. The optimum filling level is up to the trough mark.

In order to achieve uniform heating of the cleaning liquid, it is necessary to occa-sionally switch the ultrasound on or manually stir the liquid.

Without circulation of the liquid, the heat generated rises to the surface by the influence of physics. A steep temperature gradient results in the cleaning bath (the temperature differences between the surface of the liquid and the floor of the trough may be up to 40°C). Furthermore, increased calcareous deposits form in the heating area, since the resulting high temperature is not optimally dissipated into the liquid.

INFORMATION!

7 Operation


19

Duration of cleaning

In principle, the shortest possible duration of cleaning is to be set. Depending on the soiling and the cleaning liquid used (comply with the instructions on the re-spective labels of the cleaning liquids), the duration of cleaning amounts to approx. 1 to 15 minutes.

INFORMATION! Degassing the cleaning liquid increases the cleaning effect. Cleaning and contact liquids contain dissolved gases (e.g. oxygen). Ultrasonicate cleaning or contact liquids that have been freshly filled or have remained in the vibration trough for a long period for approx. 5 to 15 minutes before use. Degass vibration troughs of more than 10 l volume for approx. 30 min. During the degassing, the cavitation noise changes, loud degassing noises cease at the end of the degassing process and the device works noticeably more quietly. A lower noise level does not mean any decline in the ultrasonic output, but only the end of the degassing process.

Draining the vibration trough

Do not place the device in the sink!

Devices with a drainage hose

The trough is drained by opening the shut-off cock on the side. Before operating the device for the first time, install the elbow supplied and the drainage hose on the shut-off cock.

After draining the trough, it must be ensured by rinsing several times that there are no particles (> 300 µm) in the drain outlet.

IMPORTANT!

7 Operation


20

General guidelines for the use of cleaning products

• The maximum cleaning effect is achieved with media specially suited to ultrasonic use, e.g. JOKE®-Clean.

• Renew used cleaning and disinfection liquids; do not refresh by subse-quently adding more.

• Layers of dirt on the base of the trough or inserts (e.g. grinding and pol-ishing media and other deposits) impair performance; consequently, drain the vibration trough and clean the latter and renew cleaning liquid.

• Cleaning and contact liquid in the ultrasonic vibration bath must not ex-ceed a maximum operating temperature of 100°C.

• Distilled or deionised water is unsuitable for ultrasonic cleaning di-rectly in the vibration bath (in insert and suspension troughs, distilled or deionised water is usable both as a cleaning liquid and starting bath for other cleaning products).

• Only use cleaning preparations tested and developed for ultrasonic clean-ing, e.g. JOKE®-Clean.

CAUTION! During work with corrosive cleaning products in inserts or a suspen-sion trough, avoid projections in the contact liquid or on the stainless steel surfaces; if necessary, immediately renew the contact liquid, clean surfaces and rub dry.

No warranty is accepted for damage to the device and instruments caused by use of unsuitable cleaning or disinfection chemicals.

8 Troubleshooting


21

Finding Possible cause Remedy

Housing or mains cable damaged

Outside influence, transport damage

Send device to JOKE® service

No function; control lights not illumi-nated

Mains plug not connected

Socket devoid of current

Mains cable damaged / cut

Insert mains plug

Check socket/fuse


No ultrasonic function; Ultrasonic control light not illuminated, heating OK

Timer not activated

Timer faulty

Set timer to “on”


No ultrasonic function; Ultrasonic control light illuminated, heating OK

Electronics faulty Send device to JOKE® service

Cleaning result not sat-isfactory

No cleaner or unsuitable clean-ing medium used

Cleaning time too short

Use suitable cleaning medium

Repeat cleaning interval

Device does not heat up; Heating control light not illuminated; US can be activated

Heating switch faulty

Control thermostat faulty (no switch click audible)


Heat-up time not satis-factory

Thermal energy escapes

No circulating of the cleaning liquid

Use lid (optional accessory)

Circulate cleaning liquid

e.g. additionally switch on ultrasound (refer to page 17)

Device generates boil-ing noises when heating

No circulation of the cleaning liquid

e.g. additionally switch on ultrasound (refer to page 17)

Circulate cleaning liquid

Set temperature is ex-ceeded

Temperature sensor does not record the average temperature (no circulating)

Preselected temperature too low

Ultrasonic energy heats the liquid (physical process)

Circulate liquid manually or by ultrasound

At low set-point temperatures, omit heating

Only switch on ultrasound for a short period.

8 Care and maintenance


22

JOKE® ultrasonic cleaning devices are maintenance-free. In order to prolong the service life of the vibration trough and always achieve perfect cleaning results, regular cleaning and care of the device is necessary.

Observe the following points for cleaning:

INFORMATION! • Pull out the mains plug before any cleaning of the device.

• Do not spray down the devices or immerse the latter in water, but wet wipe the interior and exterior.

• Thoroughly rinse out and rub dry the stainless steel trough more frequently.

• Do not use any steel wool and avoid using scrapers.

• If after more prolonged use, tide-marks remain on the stainless steel surface of the vibration trough, these should be removed with a common commercially available stainless steel care product without any scouring additives.

• Remains of metal parts on the stainless steel surface in addition to rust parti-cles from the water supply system may penetrate the passive protective surface of the stainless steel, “activate” the stainless steel and cause it to begin to rust. This foreign rust causes crevice corrosion on the stainless steel. Consequently, remove any metal parts remaining behind, such as screws and metal filings, etc. and remove small rust marks immediately using a soft cloth and common commercially available stainless steel care products.

Note on repair

All the functions of every device are extensively checked before delivery. If mal-functions occur after prolonged operation, JOKE® Service should be contacted.

10 Cleaning products


23

Cleaning products

In the choice of the right cleaning product, it is essential to pay attention to suit-ability for ultrasonic troughs, since otherwise damage to the vibration trough may occur. Inflammable products are generally not allowed (refer to warnings). The products must not contain any halogenide ions or table salt, since these result in tension cracks in the trough. Acids, such as hydrochloric acid, sulphuric acid or nitric acid will very rapidly destroy the device. Particularly in the case of acid cleaners (e.g. for derusting or removing mineral contamination such as calcareous deposits) only specially formulated cleaners should be used.

We offer a comprehensive range of cleaning preparations, which guarantee a long service life for the device. Refer to our current JOKE catalogue in this connection (page 399). If products from other manufacturers are used, please observe the in-structions included, specifically concerning use in ultrasonic baths.

11 Telefax form


24

To the

JOKE service department

+49 (0) 22 04 / 8 39 - 86

Sender:

Company

Name

Street

Postcode/town or city

Please send us the spares drawing and parts

list for the following equipment:

0 as a printout (see above for address)

0 by fax, ____________________________

0 as a pdf file to my email address _____________________________

Ultrasonic cleaner Eco-Clean 30HA Ord. No. 0 668 000 0

Ultrasonic cleaner Eco-Clean 50HA Ord. No. 0 668 010 0 Ultrasonic cleaner Eco-Clean 70HA Ord. No. 0 668 020 0 Ultrasonic cleaner Eco-Clean 140HA Ord. No. 0 668 030 0

Date Signature

JOISTEN & KETTENBAUM GmbH & Co. KG Asselborner Weg 14 - 16 D-51429 Bergisch Gladbach Telefon: 0 22 04 / 8 39-0 Telefax: 0 22 04 / 8 39-60

Änderungen aufgrund technischen

Fortschrittes vorbehalten

Internet: www.joke.de E-Mail: [email protected] © JOKE® 07/04

ultrasonic cleaners - joke · 3 safety instructions joke® instruction manual eco-clean ultrasonic...

Documents