umodule spot p320-3 em umodule spot out phased€¦ · led p320-3 em 3000k 47x44 830/4x9 – 1,340...
TRANSCRIPT
www.tridonic.com 1Subject to change without notice.
Data sheet 07/12-LED057-2
U – LED modules, converters and systemsGENERAL ILLUMINATION
Product description
•Spotlights
•Downlights
•High-flux LED module
•Narrow colour temperature tolerance band
•Lifetime up to 50,000 hours
•Compact design
•Excellent thermal management1
•NTC for temperature control
•High-power LED in chip-on-board technololgy
•Beam characteristic: 140°
•Uniform distribution of light
•Fixing holes for M3 screws
•Connection: Cable 300 mm
•Built-in LED module
•Cooling required
Technical dataBeam characteristic 140°
Ambient temperature ta -30 ... +55 °C
Typ. tc point 65 °C
Weight 0.015 kg
Risk group (EN 62471:2008) 0
ÈStandards, page 3
Colour temperatures and tolerances, page 6
Umodule SPOT P320-3 EMumodule SPOT
1 Minimal reflector diameter2 Maximum reflector diameter
tc
1,652,00 typ.
NTC
Ø23
1Ø2
8,5
2Ø3,2
46,58,
5
23,5
38,5
04,58,5
35,539,5
44
0
NTCNTC
– LED+ LED
+ LED EM– LED EM
562134
Ordering dataColour temperature Type Article number
3,000 K LED P320-3 EM 3000K 47x44 89601433
4,000 K LED P320-3 EM 4000K 47x44 89601434Packaging: 20 pieces/packaging, 360 pieces/carton
Specific technical dataType Photometric
codeTyp. luminous flux at 350 mA2 3 4
Typ. luminous flux at 700 mA2 3 4
Typ. luminous flux at 1,050 mA2 3
Typ. forward voltage2 3 Power consumption module
Typ. Efficacy Colour rendering indexCRI
Normal operationLED P320-3 EM 3000K 47x44 830/4x9 – 1,340 lm 1,850 lm 28.8 V 20.2 W 67 lm/W > 80
LED P320-3 EM 4000K 47x44 840/4x9 – 1,480 lm 2,050 lm 28.8 V 20.2 W 74 lm/W > 80
Emergency operation – 350 mALED P320-3 EM 3000K 47x44 830/4x9 150 lm – – 6,2 V 2.2 W 67 lm/W > 80
LED P320-3 EM 4000K 47x44 840/4x9 160 lm – – 6,2 V 2.2 W 74 lm/W > 80All values for ta = 25 °C, tc = 65 °C.
1 If the maximum temperature limits are exceeded, the life of the module will be greatly reduced or the module may be damaged.The temperature of the umodule SPOT at the tc point in the thermally stable state by mean of a temperature sensor or temperature-sensitivesticker as per EN 60598-1. For the precise position of the tc point see the drawing above.
2 At tc = 65 °C.
3 Tolerance range for optical and electrical data: ±15 %.
4 Max. permissible surge current: 3 A, duration max. 10 µs.
PHASED
OUT
www.tridonic.com 2Subject to change without notice.
Data sheet 07/12-LED057-2
U – LED modules, converters and systemsGENERAL ILLUMINATION
Converter matrix – Umodule SPOT P320-3 EM in emergency operation
Converter for emergency operation
TypeEM powerLED
2 W BASICscrew-fix
EM powerLED2 W BASIC
clip-fix
EM powerLED2 W ST
screw-fix
EM powerLED2 W STclip-fix
EM powerLED2 W PRO EZ-3
screw-fix
EM powerLED2 W PRO EZ-3
clip-fix
Article number 89899859 89899866 89899861 89899868 89800030 89800032
Assignable converter
Type Min. Max. Min. Max. Min. Max. Min. Max. Min. Max. Min. Max.
Umodule SPOT P320-3 EM 1 1 1 1 1 1 1 1 1 1 1 1
Wiring diagram converter + Emergency device EM powerLED
562134
Uconverter
NTC
EM powerLED
Converter / controls matrix – Umodule SPOT P320-3 EM in normal operation
Converter REMOTE LCI Controls IN-BUILT
TypeLCAI 30 W700 mAone4all
LCI 30 W700 mA
LCI 50 W 1050mA
T020
LCAI 50 W 1050 mA
T020
LCI 50 W 1050 mA
R10
LCAI 50 W 1050 mA
R010C700 dim
Article number 86458900 24166314 86459218 86459247 86453216 86459245 86458945
Type Min. Max. Min. Max. Min. Max. Min. Max. Min. Max. Min. Max. Min. Max.
Umodule SPOT P320-3 EM 1 1 1 1 1 1 1 1 1 1 1 1 1 1
Product description
•Housing for LED module
•Diameter: 50 mm
TALEXXaccessory Cover Spot
ACCE
S-SO
RIES
Ordering dataTyp Article number
P 320-3 EM LED cover white D50 LES 23 mm 88167489Packaging: 20 pieces/packaging, 400 pieces/carton
WiringCable: AWG24; length 300 mm
pin 1 2 3 4 5 6function + (LED) - (LED) + (EM) - (EM) NTC (LED) NTC (LED)colour red black red black grey grey
PHASED
OUT
www.tridonic.com 3Subject to change without notice.
Data sheet 07/12-LED057-2
U – LED modules, converters and systemsGENERAL ILLUMINATION
Typical heat sink surface
NotesThe actual cooling surface can differ because of the material, the structural shape, outside influences and the installation situation. A thermal connection between umodule SPOT and heat sink with heat-conducting paste or heat conducting adhesive film is absolutely necessary.
Umodule SPOT P320-3 EM, 700 mAta tc Rth, hs-a
25 °C 65 °C 2.09 K/W30 °C 65 °C 1.81 K/W40 °C 65 °C 1.24 K/W50 °C 65 °C 0.68 K/W
For umodule SPOT P320-3 EM a tc temperature of 65 °C has to be complied in order to achieve an optimum between heat sink requirements, light output and life time.
Compliance with the maximum permissible reference temperature at the tc point must be checked under operating conditions in a thermally stable state. The maximum value must be determined under worst-case conditions for the relevant application.
Mounting instruction
umodule SPOT from Tridonic which have to be installed on a heat sink have to be connected with heat-conducting paste or heat conducting adhesive film and fixed with M3 screws with plastic washer.
The fixing/cooling surface must be cleaned before installing the u modules to remove all dirt, dust and grease.
None of the components of the umodule SPOT (substrate, LED, electronic components etc.) may be exposed to tensile or compressive stresses.
Thermal design and heat sinkThe rated life of u products depends to a large extent on the temperature. If the permissible temperature limits are exceeded, the life of the umodule SPOT will be greatly reduced or the umodule SPOT may be destroyed.
Therefore the umodule SPOT P320-3 EM needs to be mounted onto a heat sink.
Tridonic’s excellent thermal design for the umodule SPOT products provides the lowest thermal resistance and therefore allowing new compact designs without sacrificing quality, safety and life time.
tc point, ambient temperature and lifetimeThe temperature at tc reference point is crucial for the light output and life time of a u product.
Thermal behaviour
storage temperature -30 – 85 °Coperating temperature -30 – 55 °Ctc max. (at typ. current) 85 °C
StandardsEN 62031EN 62471
Umodule SPOT P320-3 EM, 1,050 mAta tc Rth, hs-a
25 °C 55 °C 0.96 K/W30 °C 55 °C 0.77 K/W40 °C 55 °C 0.40 K/W
0
200
400
600
800
1000
1200
1400
1600
0 10 20 30 40 50 60 70 80 90 100Tc [°C]
If [m
A]
0
20
40
60
80
100
120
140
160
180
200
30 40 45 55 70Temperature [°C]
Resi
stan
ce [k
Ω]25 656035 50 75
220
240
80 85
Normal operation Pin 1&2
Temperature controlAn NTC resistor is on the board of the umodule SPOT P320-3 EM to control the tc temperature during the operation.Exact position see drawing on page 1.The details of the 220 kΩ NTC (order number B57431V2223J062) you can find in the data sheet of the manufacturer AVX (Nr. NB12QØØ224).
EOS/ESD safety guidelines
The device / module contains components that are sensitive to electro-static discharge and may only be installed in the factory and on site if appropriate EOS/ESD protection measures have been taken. No special measures need be taken for devices/modules with enclosed casings (contact with the pc board not possible), just normal installation prac-tice. Please note the requirements set out in the document EOS / ESD guidelines (Guideline_EOS_ESD.pdf) at: http://www.tridonic.com/com/en/technical-docs.asp
1st digit 2nd + 3rd digit 4th digit 5th digit 6th digit
Code CRIColour temperature in
Kelvin x 100McAdams
initial
McAdams after 25% of the
lifetime (max.6000h)
Lumen maintanance after 25% of the lifetime (max.6000h)
Code Remaining lumen7 67 – 76 7 ≥ 70 %8 77 – 86 8 ≥ 80 %9 87 – ≥90 9 ≥ 90 %
Photometric code
Key for photometric code, e. g. 830 / 559
PHASED
OUT
www.tridonic.com 4Subject to change without notice.
Data sheet 07/12-LED057-2
U – LED modules, converters and systemsGENERAL ILLUMINATION
Lifetime
tc temperature in °C luminous flux in % lifetime in h
2580 60,00070 81,00050 132,000
4580 44,00070 64,00050 110,000
6580 32,00070 50,00050 91,000
7580 25,00070 41,00050 81,000
f(soldering time) for the modules
Temperature Max. timewithout heat sink
Max. timewith optimized heat sink
330 °C 15 s –340 °C 12 s –350 °C 10 s –360 °C 5 s 15 s370 °C 3 s 12 s380 °C 2 s 10 s390 °C 1 s 5 s
Matrix temperature
The values apply for soldering without heat sink. To reduce the duration of soldering it is recommended to pre-heat the module at ta max., e.g. on a plate.
Electrical supply/choice of converterumodule SPOT from Tridonic are not protected against overvoltages, overcurrents, overloads or short-circuit currents. Safe and reliable operation can only be guaranteed in conjunction with a converter which complies with the relevant standards. The use of u converters from Tridonic in combination with umodule SPOT guarantees the necessary protection for safe and reliable operation.
If a converter other than Tridonic uconverter is used, it must provide the follow-ing protection:•Short-circuitprotection•Overloadprotection
•Overtemperatureprotection
umodule SPOT P320-3 EM must be supplied by a constant current converter.Operation with a constant voltage converter will lead to an irreversible damage of the module.
Wrong polarity can damage the umodule SPOT P320-3 EM.
0
200
400
600
800
1000
1200
1400
1600
0 10 20 30 40 50 60 70 80 90 100Tc [°C]
If [m
A]
1800Emergency operation Pin 3&4
PHASED
OUT
www.tridonic.com 5Subject to change without notice.
Data sheet 07/12-LED057-2
U – LED modules, converters and systemsGENERAL ILLUMINATION
Relative forward voltage and relative luminous flux in normal operation
0,97
0,98
0,99
1
1,01
1,02
1,03
1,04
1,05
20 30 40 50 60 70Tc [°C]
rel.
volta
ge [a
.u.]
80 85
0,92
0,94
0,96
0,98
1
1,02
1,04
1,06
1,08
1,1
1,12
1,14
30 40 50 60 85Tc [°C]
rel.
lum
inou
s flu
x [a
.u.]
20 80700,20
0,40
0,80
1,00
300 700current [mA]
rel.
lum
inou
s flu
x [a
. u.]
Relative luminous flux at tc = 65 °C
500200
1,40
900 11001000800600400
0,60
1,20
0,9
0,95
1,00
1,05
300 700current [mA]
rel.
volta
ge [a
. u.]
Relative forward voltage at tc = 65 °C
500200
1,10
900 11001000800600400
PHASED
OUT
www.tridonic.com 6Subject to change without notice.
Data sheet 07/12-LED057-2
U – LED modules, converters and systemsGENERAL ILLUMINATION
Optical characteristics Umodule SPOT P320-3 EM
The optical design of the umodule SPOT product line ensures optimumhomogenity for the light distribution.
0°
20
20
-20 40
40
60
60
80
100
80 100-40-60-80-100
10°-10° 20°-20°-30°
-40°
-50°
-60°
30°
40°
50°
60°
70°
80°
90°-90°0
rela
tive
inte
nsity
Iv/Iv
,max
Umodule SPOT P320-3 EM 140°: Light distribution
0,97
0,98
0,99
1
1,01
1,02
1,03
1,04
1,05
20 30 40 50 60 70Tc [°C]
rel.
volta
ge [a
.u.]
80 85
0,92
0,94
0,96
0,98
1
1,02
1,04
1,06
1,08
1,1
1,12
1,14
30 40 50 60 85Tc [°C]
rel.
lum
inou
s flu
x [a
.u.]
20 8070
Relative forward voltage and relative luminous flux in emergency operation
0,9
0,95
1,0
1,05
1,1
300200 700 800500current [mA]
rel.
volta
ge [a
. u.]
Relative forward voltage at tc = 65 °C
400 600100
1,15
0,20
0,40
0,80
1,00
1,20
1,40
1,60
1,80
100 200 300 400 500 600 700 800
current [mA]
rel.
lum
inou
s flu
x [a
.u.]
Relative luminous flux at tc = 65 °C
0,60
The diagrams based on statistic values.The real values can be different.
PHASED
OUT
www.tridonic.com 7Subject to change without notice.
Data sheet 07/12-LED057-2
U – LED modules, converters and systemsGENERAL ILLUMINATION
Coordinates and tolerances according to CIE 1964
The specified colour coordinates are measured by a current impulse of 700 mA and a duration of 100 ms.The ambient temperature of the measurement is ta = 25 °C.The measurement tolerance of the colour coordinates are ± 0.01.
MacAdam ellipse: 4SDCM
0,3800
0,3850
0,3900
0,3950
0,4000
0,4050
0,4100
0,4150
0,4200
0,42
50
0,43
00
0,43
50
0,44
00
0,44
50
0,45
00
0,45
50
0,46
00
0,46
50
3,000 Kx0 y0
Centre 0,4460 0,3990
380 420 460 500 540 580 620 660 700 740 780
wave length [nm]
norm
. int
ensi
ty [%
]
0
20
40
60
80
100
MacAdam ellipse: 4SDCM
0.3600
0.3650
0.3700
0.3750
0.3800
0.3850
0.3900
0.3950
0.4000
0.36
50
0.37
00
0.37
50
0.38
00
0.38
50
0.39
00
0.39
50
0.40
00
0.40
50
4,000 Kx0 y0
Centre 0,3860 0,3780
380 420 460 500 540 580 620 660 700 740 780
wave length [nm]
norm
. int
ensi
ty [%
]
0
20
40
60
80
100
PHASED
OUT