upcycling children wooden building...
TRANSCRIPT
UPCYCLING children wooden building blocks
As a mum I often get surprised how fast our children grow and decide to exchange sim-
ple and basic toys for more complicated ones.
To keep at least a memento of a long gone period I decided to up cycle a some of my son
Lucas wooden building blocks, and I’ll think they’ll look lovely standing on the cupboards
in his room.
Because he’s a little engineer in spe, it wasn’t difficult to choose a theme to “dress up” the
blocks, you are free to use your imagination to make yours!
MAIN INGREDIENTS
RE-UTILIZANDO bloques de madera para niños
Siendo madre de dos niños muchas veces me quedo sorprendida de la
rapidez en que crecen y dejan sus juguetes simples y básicos para cambiar-
los por otros muchos más complicados.
Para guardar por lo menos un recuerdo de los períodos que han pasado he
decicido re-usar algunos de los bloques de madera de mi hijo Lucas para
luego ponerlos de adorno en su habitación.
Como ya tiene tendencias de ingeniero, no me ha sido difícil elegir un
tema para adornar los bloques, ustedes son libres de elegir tema propio, por
su puesto!
TOOLS
herramientas
DRESS UP INGREDIENTS
ingredientes
electric wire
cable eléctrico
all sorts of hardware
todo tipo utensillos
hemp cord
cuerda
“the block”
“el bloque”
You will have to be a bit patient with me, I am really not familiar with the names of all the
tools, I only know how to use them though!
I started with the front, making the eyes.
I used this drill piece to make them, they are not measured out, that will give more per-
sonality to the face!
Les pido un poco de paciencia ya que en realidad no sé los nombres
correctos de muchas herramientas, pero sé cómo utilizarlas....: )
He comenzado con el frente del bloque, hacienda los ojos. Los agujeros no
han sido medidos previamente, yo creo que así el bloque tendrá más
“carácter”.
For the arms I decided to use two
screws on this little fellow.
A fast way to be sure I drill the holes
correctly is by using masking tape, I
did this on the front and the sides of
the block, so I could be sure the arms
would be horizontal.
I drilled a 3mm hole into both sides of
the block and screw the screws into
them
Look! A cute little red robot is
appearing!
El pequeño robot ya
está apareciendo!
Para los brazos he usado
tornillos, una manera rápida
de asegurar que los agujeros
estén más o menos alineados es
usando cinta adhesiva
Con una mecha para madera
he hecho agujeros de 3mm. En
ambos lados del bloque. Ahora
se pueden poner los tornillos
I decided to give the block a punk
look by using some blue electrical
cable
Good quality pliers from my hus-
band’s tool box come in handy to cut
appropriate legths of “hair”.
I decide to cut 5x pieces of different
lengths each
He decidido que el cabello del
robot estará hecho con cables
de electricdad .
The tool you see on the left are great
to skim off some of the blue plastic
…… and leave some shiny copper
fore some more detail.
If your child is too small, though, I
wouldn’t recommend it, they have
sharp points.
He cortado 5x pedacitos de
diferentes tamaños y con la
herramienta de la izquierda he
sacado un poco del plástoco
azul cobertor del cabe, para
darle un poco más de sabor....
Decide where the cable pieces will go
and mark on top of the block before
you drill the holes
First I drilled holes of 2mm and then
of 4mm on the previous hole, this is
far better than drilling 4mm all at
once, the wood is quite hard (wood
grain side of the wood!) and I might
hurt myself , so be careful!
Antes de taladrar los agujeros,
he marcado los puntos en la
parte de arriba del blque para
guiarme mejor
Esta vez he comenzado por
hacer agujeros de 2mm y luego
de 4mm en los agujeros de
2mm, es mejor agrandar los
agujeros de a poco, la madera
es fuerte y uno se puede
lastimar!
I’ve used a hot gun to glue the wire to the
block and voilá, a punk robot is born!
He pegado el cable con una hot
gun y el punk robot ya está listo!