uponor radiant heating/cooling katalog ufh-c 2012 eng.pdf · 6 eei-int-rhc-01.12 radiant heating...
TRANSCRIPT
I N D O O R C L I M AT E S O LU T I O N S
P R O D U C T C ATA LO G 2 0 1 2
Uponor Radiant Heating/Cooling
Uponor Renovationsystem Minitec
Uponor Minitec - System components and accessories ·························································· 8
Uponor lightweight panel Siccus
Uponor Siccus - System components and accessories ···························································· 11
Uponor pipe positioning panel Tecto
Uponor Tecto - System components and accessories ······························································ 14
Uponor self attaching system
Uponor self attaching system - System components and accessories ····································· 19
Uponor stapler and clamp track
Uponor stapler and clamp track - System components and accessories ·································· 22
Uponor pipe positioning panel
Uponor pipe positioning panel - System components and accessories ··································· 27
Uponor steel mesh Classic
Uponor Classic - System components and accessories ···························································· 32
Uponor Plaster Ceiling Cooling
Uponor Plaster Wall/Ceiling H/C - System components and accessories ······························· 35
Uponor heat emission plate ······························································································· 38
Uponor Radiant Heating/Cooling > List of content
List of content
Abbreviations ······················································································································ 4
EEI-Int-RHC-01.12 3
Uponor underfloor heating accessories
Uponor underfloor heating accessories ·················································································· 39
Uponor underfloor heating manifolds
Uponor modular plastic manifolds ·························································································· 42
Uponor accessories for plastic manifolds ················································································ 43
Uponor stainless steel manifolds ···························································································· 45
Uponor manifold accessories ·································································································· 46
Uponor pipe bend support ····································································································· 48
Uponor manifold cabinets ······································································································ 48
A/F [mm] across flats
A [m²] square measure
c/c [mm] centre - centre distance
c/c1 [mm] centre - centre distance 1
colour [-] colour
Con. [l/m²] consumption
d [mm] diameter
d1 [mm] diameter 1
d2 [mm] diameter 2
d3 [mm] diameter 3
di [mm] diameter inside
DN [mm] diameter nominal
DT [d] drying time in days
EP/a [W] effective power per actuator
FT ["] female thread
FT m [-] female thread (metric)
G [kN/m²] load bearing capacity
h [mm] height
h1 [mm] height 1
h2 [mm] height 2
l [mm] length
l [m] length in meter
l1 [mm] length 1
MT ["] male thread
outlets [-] Number of outlets
OV [V] operating voltage
p [bar] pressure
P [W] effective power
Q [kW] nominal power
r [mm] radius
R-value [m²K/W] thermal resistance
s [mm] strength / wall thickness
sd [mm] side distance
stroke [mm] stroke
Type [-] Type
V [l/m] volume
w [mm] width
w [m] width in meter
w1 [mm] width 1
w2 [mm] width 2
z [mm] z-value
Δ Lw [dB] impact noise improvement
Uponor Radiant Heating/Cooling > Abbreviations
Abbreviations
EEI-Int-RHC-01.124
Shortcut unit Description
Uponor controls
Uponor Radio control ············································································································· 50
Uponor outdoor sensor ·········································································································· 54
Uponor wired control ············································································································· 55
Uponor control accessories 24 V ···························································································· 59
Uponor wired control 230 V ··································································································· 60
Uponor control accessories 230 V ·························································································· 61
Uponor climate controller ······································································································· 63
Uponor control stations ·········································································································· 67
Uponor industrial underfloor heating
Uponor industrial floor heating PE-Xa pipes ·········································································· 71
Uponor PE-Xa Q&E fittings ···································································································· 72
Uponor industrial floor heating fixation and accessories ························································ 73
Uponor industrial floor heating manifold and accessories ······················································ 75
Uponor snow and ice melting
Uponor snow and ice melting pipes························································································ 77
Uponor snow and ice melting manifold and accessories ························································· 78
Uponor sport floor heating
Uponor sport floor PE-Xa pipes ······························································································ 83
Uponor sport floor PE-Xa Q&E fittings ·················································································· 84
Uponor sport floor fixation and accessories ··········································································· 85
Uponor comfort panel
Uponor comfort panel ············································································································ 88
Uponor comfort panel - accessories ······················································································· 90
Uponor gypsum panel
Uponor gypsum panel ············································································································ 96
Uponor gypsum panel - accessories ······················································································· 97
Uponor tools
Uponor tools ·························································································································· 99
Uponor Radiant Heating/Cooling > List of content
List of content
EEI-Int-RHC-01.12 5
International sales and delivery terms ············································································· 105
Item search register ············································································································ 107
How to contact us ··············································································································· 111
6 EEI-Int-RHC-01.12
Radiant heating and cooling systems - for all areas of application the right system
Radiant heating and
cooling systems
Accessory systems
Floor – Renovation
Floor – new build, SFH, MFH, public
buildings
Wall/Ceiling - new build and
renovation
Minitec
Minimum height, maxi-
mum comfort
Fittings
For each pipe a save
connection
Siccus
The lightweight for
renovation
UFH accessories
To have the right
accessories is what
matters
Tecto
For fast and accurate
laying
Manifolds
Balanced distribution of
heat into the last corner
Self attaching system
Micro interlocking for
maximum holding force
Cabinets
For surface and fl ush
installation
Special Applications
Industrial UFH
Heating/Cooling of
productions halls,
warehouses or logistic
centers
Snow & ice melting
Keeping areas snow &
ice free
Sports fl oor heating
Sports fl oor heating for
surface elastic fl oors
Comfort panel
Ceiling cooling for
suspended ceilings
x
x
x
x
x x
x
x
x
x
x
x
x
x
7EEI-Int-RHC-01.12
Stapler and clamp track
Versatile through
fl exible pipe laying
Pipe positioning panel
14 – 16
For fast and accurate
laying
Classic
Proven for years, precise
laying
Controls
Wired or wireless
controlled, sensitive and
comfortable
20,5
Control stations
Energy effi cient supply
temperature control
Tools
which makes the work
easier
Plaster Wall/Ceiling
Multifunctional for wall
and ceiling
Ceiling cooling
systems
Gypsum panel
Ceiling cooling for
gypsum board ceilings
Contec
The storable concrete
core activation
Contec ON
The highly effi cient
surface close building
part activation
Stapler and clamp track
Versatile through
fl exible pipe laying
Pipe positioning panel
14 – 16
For fast and accurate
laying
Classic
Proven for years, precise
laying
Controls
Wired or wireless
controlled, sensitive and
comfortable
20,5
Control stations
Energy effi cient supply
temperature control
Tools
which makes the work
easier
Plaster Wall/Ceiling
Multifunctional for wall
and ceiling
Ceiling cooling
systems
Gypsum panel
Ceiling cooling for
gypsum board ceilings
Contec
The storable concrete
core activation
Contec ON
The highly effi cient
surface close building
part activation
x
x
x
x
x
x
x
x x
x
x
x
Uponor Radiant Heating/Cooling > Uponor Renovationsystem Minitec
EEI-Int-RHC-01.128
Fast installation, short heat-up
time: the Uponor renovation-
system Minitec off ers you a
range of advantages. The
Uponor minitec foil element for
the laying of the PE-Xa pipes
measures 9.9 x 1.1 mm and
can be installed on any existing
screed, timber of tiled fl oor. Thanks to this small element height of
around one centimetre, the system is particularly suitable for inte-
gration into existing buildings.
Your advantages Ideal for retrofi tting in existing buildings during renovations
Suitable for direct installation on screed or tiled fl oors
Elements height only 12 milimeter
Low-cost installation of foil elements and pipe
Foil elements can be walked over immediately aft er installa-
tion
Short heat-up times
Low heating water temperatures
Can be connected directly to existing radiant heating sys-
tems
System components
Uponor high performance panel
Room controls
Uponor radio controlUponor wired control 24 V230 V components
Control stations
Uponor control stations - overview
System pipe/fi ttings
Uponor PE-Xapipe 9,9 x 1,1
Additional components
Uponor Minitecedging strip
Manifold/Cabinets
Uponor PE-Xa Q&E coupling
Uponor Minitecjoint profi le
Uponor Minitecclamp track 9.9
Uponor PE-Xa conversion nipple
Uponor renovationsystem Minitec
Uponor Minitecjoint protection
Uponor pipe connection PE-Xa 9.9
Uponor PE-Xa Pipe 9.9x1.1 expander
20,5
Uponor cabinet
Uponor manifold connection valve set G 1/Rp 1
Uponor manifold
e.g. can be used with Knauf Levelling Screed 425
Uponor Radiant Heating/Cooling > Uponor Renovationsystem Minitec
Uponor Minitec - System components and accessories
Uponor Minitec high-performance panelDesigned as sturdy pipe fixing panel of minimum height, with integrated
pipe laying channels for correct pipe laying distances; designed for Uponor
Minitec PE-Xa pipes 9.9 x 1.1 mm; allowing for straight and diagonal
pipe laying; with undercut, deep pipe fixing studs; overlap on both sides
with triangular studs; perforated panel for installation between levelling
compound and substructure; with self-adhesive back for proper fixture to
screed and tiled floors
Material: Polystyrene
DIN 4102 building material class: B2
Pipe spacing: Vz 5, 10, 15
Colour: traffic black (near RAL 9017)
Item no. h [mm] l [mm] w [mm] A [m²] Description unit
1005261 12 1120 720 0.77Uponor Minitec high performance panelwith,self-adhesive layer for pipes 9.9mm 15.4 m²
Uponor PE-Xa pipesPE-Xa pipe with an oxygen diffusion barrier manufactured from peroxide
cross-linked polyethylene (PE-Xa) using the Engel method complying
with e.g. prENISO 15875 “Plastics piping systems for hot and cold water
installations - Cross-linked polyethylene” with an oxygen diffusion barrier
of EVOH (ethyl vinyl alcohol). Uponor pipes fulfil the requirements for
oxygen diffusion resistance as per DIN 4726. Malfunction temperature
95°C. Design pressure 8,8 bar (at 70°C).
Item no. d [mm] s [mm] l [m] V [l/m] Description unit
1033024 9.9 1.1 120 0.047Uponor eval PE-Xa pipe 9.9x1.1
120 m
1033025 9.9 1.1 480 0.047Uponor eval PE-Xa pipe 9.9x1.1
480 m
1033026 9.9 1.1 240 0.047Uponor eval PE-Xa pipe 9.9x1.1
240 m
Uponor PE-Xa Q&E coupling 9.9For Uponor PE-Xa pipe 9.9 x 1.1 mm, consisting of:
- 1 coupling
- 2 PEX Q&E rings for secure connection
Material: Coupling made in brass; PEX Q&E rings made in high-pressure
cross-linked polyethylene
Item no. d [mm] s [mm] l [mm] z [mm] Description unit
1005264 9.9 1.1 34 4Uponor PE-Xa Q&E coupling 9.9-9.9with two PEX rings 10 pcs
Uponor PE-X ring for PE-Xa pipesFor Uponor Minitec PE-Xa pipe 9.9 x 1.1 mm; to secure fixing to Minitec
fittings
Material: High-pressure cross-linked polyethylene (PE-Xa)
Item no. d [mm] Description unit
1005263 9.9Uponor PE-X ring for PE-Xa pipes9.9 x 1.1 10 pcs
Uponor PE-Xa conversion nippleFor Uponor PE-Xa pipes 9.9 x 1.1 mm, made of brass.
Item no. d [mm] MT ["] l [mm] z [mm] A/F [mm] Description unit
1005265 9.9 R 1/2 39 14 22Uponor PE-Xa conversion nipple9.9 - 1/2 with one PEX ring 10 pcs
EEI-Int-RHC-01.12 9
Uponor Radiant Heating/Cooling > Uponor Renovationsystem Minitec
Uponor Minitec - System components and accessories
Uponor edging strip, 80x8Edging strip for high performance panel conforming to DIN 18560, made
of polyethylene with self-adhesive backing, self-adhesive strip on outer
face provides tight seal between edging strip and insulation;
Length of roll: 20 m
Item no. h [mm] l1 [mm] s [mm] l [m] Description unit
1005267 80 70 8 20Uponor Minitec edging strip, 80 x 8in length of 20 m 200 m
Uponor joint profile 40x10Self-adhesive clamp-on profile element for high performance panel made
of hard PVC with polyethylene foam expansion strip, for the reliable
separation of screed sections (e.g. in doorways), and to absorb expansion
of screed. For expansion joints as per DIN 18560-2.
Height: 40 mm
Material thickness: 10 mm
Length: 1,8 m
Item no. l [mm] s [mm] w [mm] h [mm] Description unit
1005268 1800 10 50 40Uponor Minitec joint profile40 x 10, length 1.8 m 18 m
l
b
s
Uponor joint protection 9.9mmMade of PE-LD, with slit opening, for protection of pipes up to 9.9 mm in
areas of expansion joints.
Length: 300 mm
Item no. l [mm] s [mm] w [mm] Description unit
1005269 300 2 35Uponor joint protection tube forPE-Xa pipes 9.9 x 1.1, length 300 mm 30 pcs
ra
d
h
l b
Uponor clamp track 9.9Self-adhesive U-profile strip made of recycled material, with integrated
pipe holder for 9.9 x 1.1 mm Uponor PE-Xa pipes.
Length of track: 2.5 m
Width of track: 24 mm
Space between pipe holders: 20 mm c/c
Installation height with pipe: 13 mm
Item no. l [mm] w [mm] h [mm] d [mm] c/c [mm] Description unit
1005274 2500 24 13 10 20Uponor clamp track 9.9 mm
25 m
EEI-Int-RHC-01.1210
Uponor Radiant Heating/Cooling > Uponor lightweight panel Siccus
EEI-Int-RHC-01.12 11
e.g. can be used with Knauf Brio Pre-fab Floor Screed Elements
Uponor lightweight panel Siccus
The Uponor lightweight panel
Siccus has been specially
designed as a universal solu-
tion for the restoration of old
buildings where a low con-
struction height and low
weight are very important.
The panels are installed on the
fl oor below the load distribution layer consisting of dry screed
panels or heating screeds.
Your advantages Minimum fl oor construction height from 50 mm
Short installation time, immediately accessible if installed
with dry screed
Low static weight from 25 kg/m² Last with dry screed
panels
Specially devised installation panel for universal use
System components
Uponor Siccus lightweight panel
Uponor Siccusheat emission plate
Uponor PE Foil 0.2mmPE-type 200
Room controls
Uponor radio controlUponor wired control 24 V230 V components
Control stations
Uponor control stations - overview
20,5
Additional components
Uponor edging strip
Manifold/Cabinets
Uponor manifold
Uponor joint profi le 100x10
Uponor compression adapter PE-Xa and MLCP
Uponor joint protection 20mm
Uponor marking set
Uponor screed additive
Uponor PE foil 0.2 mm
Uponor cabinet
Uponor manifold connection valve set G 1/Rp 1
Systempipe/-Fittings
PE-Xa pipe 14x2
Uponor MLCP 14 pipe
MLC press coupling14x2
Uponor PE-Xa Q&E coupling
Uponor Radiant Heating/Cooling > Uponor lightweight panel Siccus
Uponor Siccus - System components and accessories
Uponor Siccus lightweight panel
Pipe fixing panel for butt joint installation; with pipe channels for the
installation of heat emission plates or Uponor PE-Xa pipes
14 x 2 mm and Uponor MLCP pipes 14 mm
Material: Expanded polystyrene rigid foam according to DIN EN 13163
DIN 4102 building material class: B1
Application type according to DIN 4108-10: DEO
Compressive strength: = 150 kPa
Technical data
Plate size: 1197 x 1050 mm
Plate thickness: 25 mm
Thermal resistance: 0.622 m2 K/W
Payload: 7.5 kN/m2
Pipe spacing: 15 cm, 22.5 cm or 30 cm
Item no. l [mm] w [mm] h [mm] A [m²] Description unit
1005485 1197 1050 25 1.25Uponor Siccus lightweight panel
12.5 m²
l
b
Uponor heat emission plate 14 mm
For installation on Uponor lightweight panel; ensures uniform heat
distribution and proper fixture of Uponor PE-Xa pipes 14 x 2 mm and
Uponor MLCP RED radiant heating pipes 14 x 1.6 mm; with double
perforations for easy cutting to size.
Material: Aluminium
Plate size: 120 x 1180 mm
Plate thickness: 0.45 mm
Material requirement:
Pipe spacing Va 15 = 5.6 plates/m2
Pipe spacing Va 22.5 = 3.7 plates/m2
Pipe spacing Va 30 = 2.8 plates/m2
Item no. l [mm] w [mm] Description unit
1005486 1180 120Uponor Siccus heat emission plate 14 mmfor lightweight panel, 1180 x 120 mm 48 pcs
Uponor PE foil 0.2mm
For installation on Uponor insulation or on standardised insulating material
approved for the intended purpose for areas without stud foil. Prevents
screed penetrating the underlying insulation.
Dimensions: 4 m x 2.5 m
Thickness: 0.2 mm
Item no. l [m] w [m] s [mm] Description unit
1005049 60 1.25 ~0.2Uponor PE foil 0.2 mm thickness60 x 1.25 m 75 m²
Uponor PE-Xa pipe
as coil, for use as radiant heating pipe, connected by Q&E, press or clamp
fittings.
Material: Uponor PE-Xa pipe made in high-pressure cross-linked
polyethylene (Engel method), conforming to DIN 16892 and DIN ISO
15875, oxygen-tight according to DIN 4726
Colour: white with black and red longitudinal stripes
Uponor PE-Xa pipe
Max. operating temperature: 90°C
Max. operating pressure: 6 bar at 70 °C
Application class: 4 / 6 bar
Item no. d [mm] s [mm] l [m] Description unit
1048290 14 2 240Uponor eval PE-Xa Q&E pipe 14x2.0240 m coil 240 m
1048291 14 2 640Uponor eval PE-Xa Q&E pipe 14x2.0640 m coil 640 m
EEI-Int-RHC-01.1212
Uponor Radiant Heating/Cooling > Uponor lightweight panel Siccus
Uponor Siccus - System components and accessories
Uponor MLCP white in coils
Diffusion-tight multi-layer composite pipe (PE-RT - adhesive -
longitudinally welded aluminium - adhesive - PE-RT) for distribution
conduits, rising mains and connection lines for plumbing, radiator
connection and fancoil connection. Fire classification E according to DIN
EN 13501-1. Pipe end caps as hygienic seal according EN 806.
Resistance of temperature:
Tap water: The maximum permanent operating temperature exists between
0°C and 70°C at a maximum permanent operating pressure of 10 bars. The
short-term malfunction temperature is 95°C of a maximum of 100 hours in
the operating lifetime.
Heating: The maximum permanent operating temperature is 80°C at
a maximum permanent operating pressure of 10 bars. The short-term
malfunction temperature is 95°C of a maximum of 150 hours in the
operating time per year.
Item no. d [mm] s [mm] l [m] Description unit
1013366 14 2.0 200Uponor MLCP 14x2white in coils 200m 200 m
Uponor Q&E Coupling
for Uponor PEXa pipe consisting of:
1 Coupling / Brass
2 PEX-Rings for secure connection / cross linked Polyethylene
Item no. d [mm] Description unit
1058659 14Uponor Q&E Coupling 14with two eval Rings, nature 10 pcs
Uponor Q&E Ring natural
Made of PE-X. Uponor rings natural intended for Uponor Q&E fittings.
Item no. d [mm] colour [-] Description unit
1058428 14 naturalUponor Q&E ring eval without stop edgenature 14 20 pcs
Uponor press coupling MLC up to 32
Made of tin-plated brass, with fixed press sleeve, stop ring, pressed
identification, colour code and test safety. Press without bevel.
Item no. d [mm] Description unit
1015154 14Uponor press coupling MLC 14-14
10 pcs
EEI-Int-RHC-01.12 13
Uponor Radiant Heating/Cooling > Uponor pipe positioning panel Tecto
EEI-Int-RHC-01.1214
Uponor pipe positioning panel Tecto
The Uponor Tecto pipe posi-
tioning panel has been spe-
cially developed for the instal-
lation of underfl oor heating/
cooling systems in residential
and non-residential buildings.
The panels are installed in the
fl oor below the cement or
anhydrite screed load distribution layer. Uponor Tecto panels are
available in two diff erent thicknesses (ND 30-2 and ND 11),
catering for various fl oor constructions and load-bearing require-
ments.
Your advantages
Cost-effi cient one-man installation
Easy laying thanks to large panels (1450 x 850 mm)
Compensation elements for doors, movements joints and
wall joints available
Double-sided strips for easy connection of element cut-off s
with minimum waste
Diagonal pipe fi xture for installation at 45° angles
Suitable pipe sizes from 14 to 17 mm
Ensures standardised pipe spacing due to forced pipe paths
Proper covering of the insulating layer thanks to integrated
sturdy deep-drawn foil
Suitable for a wide range of applications thanks to high
strength properties (ND 30-2: 500 kg/m²; ND 11: 3.0 t/
m²)
System components
Uponor Tecto pipe
positioning panel
ND 11 + 30-2
Uponor Tecto double sided
strips
Uponor Tecto pipe fi xation
element
Uponor Tecto PE foil for
compensation
element
Uponor Tecto PE foil for
compensation
element in 45°
14 — 1714 — 17
Room controls
Uponor radio control
Uponor wired control 24 V
230 V components
Control stations
Uponor control stations - overview
20,5
Additional components
Uponor edging strip
Manifold/Cabinets
Uponor manifold
Uponor joint profi le
100x10
Uponor compression adapter
PE-Xa and MLCP
Uponor joint protection
20mm
Uponor marking set
Uponor screed
additive
Uponor PE foil 0.2 mm
Uponor cabinet
Uponor manifold connection
valve set G 1/Rp 1
Systempipe/-Fittings
PE-Xa pipe
14 + 17
Uponor PE-Xa Q&E coupling
MLC press coupling
14x2 + 16x2
MLCP pipe
14 + 16
Uponor Radiant Heating/Cooling > Uponor pipe positioning panel Tecto
Uponor Tecto - System components and accessories
Uponor pipe positioning panel with insulation
ND 30-2
Pipe fixing panel ND 30-2 for pipes 14 - 17 mm with heat and sound
insulation. Made of expanded polystyrene insulation covered by a black
polystyrene foil acc. to DIN EN 13163. DIN EN 13501-1 fire classification:
class E. Building-material class B2 conforming to DIN 4102. Approved for
moving loads of up to 5.0 kN/m².
Thermal resistance: 0.75 m²K/W.
For pipe spacing in cm: 10, 15, 20, 25, 30.
Dimensions: 1.45 m x 0,85 m
Panel height: 52 mm
Item no. h1 [mm] h2 [mm] l [mm] w [mm] A [m²] Δ Lw [dB] Description unit
1005478 52/50 30-2 1450 850 1.12 28Uponor Tecto pipe positioning panel incl.Insulation for dim. 14-17, thickness 30mm 8.96 m²
Uponor pipe positioning panel with insulation ND 11
Pipe fixing panel ND 11 for pipes 14 - 17 mm with heat insulation. Made
of expanded polystyrene insulation covered by a black polystyrene foil acc.
to DIN EN 13163. DIN EN 13501-1 fire classification: class E. Building-
material class B2 conforming to DIN 4102. Approved for moving loads of
up to 30 kN/m². Thermal resistance: 0.275 m²K/W. For pipe spacing in
cm: 10, 15, 20, 25, 30.
Dimensions: 1.45 m x 0,85 m
Panel height: 33 mm
Item no. h1 [mm] h2 [mm] l [mm] w [mm] A [m²] Δ Lw [dB] Description unit
1005477 33 11 1450 850 1.12 0Uponor Tecto pipe positioning panel incl.Insulation for dim. 14-17, thickness 11mm 15.68 m²
> PS-E <b
l h
Uponor compensation insulation element ND 30-2
as heat-/sound insulation for use with the compensation element covering
foil in door or wall area.
Material: Expanded polystyrene hard foam acc. to DIN EN 13163
Building class according to DIN 4102: B2
Thermal resistance: 0.75 m²K/W.
Approved for moving loads of up to 5.0 kN/m².
Item no. h [mm] l [mm] w [mm] Δ Lw [dB] A [m²] Description unit
1005480 30-2 1400 150 28 0.21Uponor Tecto compensationinsulation element - thickness 30-2mm 8.4 m
l h
b
> PS
Uponor compensation insulation element ND 11
as heat-/sound insulation for use with the compensation element covering
foil in door or wall area.
Material: Expanded polystyrene hard foam acc. to DIN EN 13163
Building class according to DIN 4102: B2
Thermal resistance: 0.275 m²K/W.
Approved for moving loads of up to 30 kN/m².
Item no. h [mm] l [mm] w [mm] Δ Lw [dB] A [m²] Description unit
1005479 11 1400 150 0 0.21Uponor Tecto compensationinsulation element - thickness 11mm 22.4 m
EEI-Int-RHC-01.12 15
Uponor Radiant Heating/Cooling > Uponor pipe positioning panel Tecto
Uponor Tecto - System components and accessories
> PS <
bb
1
l
l1
Uponor PE-foil for compensation element
For use with compensation-insulation ND 11 or ND 30-2 in door or wall
area, consists of:
- covering foil with cutter raster, single overlapping, pipe fixing foil for
secure connection of compensation elements on the Tecto elements
Material: PS-foil
Building class according to DIN 4102: B2
Colour of leveling foil: black, approx. RAL 9017
Item no. l [mm] l1 [mm] w [mm] w1 [mm] A [m²] Description unit
1005481 1400 1450 200 150 0.21 Uponor Tecto PE-foil forcompensation insulation element 28 m
b
> PS <
Uponor pipe fixation element 45°
Consist of 2 pipe fixing naps connected with one pipe fixation element as
stripe with 3 fixations for diagonal installation of Uponor pipes on Uponor
Tecto pipe positioning panel. Each stripe is separable in 3 fixation elements.
Material: Black deep drawing PS foil. Building-material class B2 conforming
to DIN 4102.
Item no. w [mm] Description unit
1005482 75Uponor Tecto pipe fixation elementfor diagonal installation 10 pcs
Uponor PE-foil for compensation element in 45°
Covering foil in 45° version for use with compensation-insulation ND 11 or
ND 30-2 in door or wall area, consists of:
- covering foil with cutter raster, single overlapping, pipe fixing foil for
secure connection of compensation elements on the Tecto elements
Material: PS-foil
Building class according to DIN 4102: B2
Colour of leveling foil: black, aprox. RAL 9017
Item no. l [mm] l1 [mm] w [mm] w1 [mm] A [m²] Description unit
1005483 1343 1414 225 150 0.2Uponor Tecto PE-foil forcompensation insulation element in 45° 26.8 m
> PS <
l
h
b
l1
Uponor double-sided strip
Foil strips with pipe fixing studs in two rows for the proper connection of
Tecto elements ND 11 or ND 30-2 (butt joints)
Material: Deep drawn PS foil
DIN 4102 building material class: B2
Colour of cover foil: traffic black (near RAL 9017)
Item no. l [mm] l1 [mm] w [mm] h [mm] Description unit
1005484 1350 1400 100 22Uponor Tecto double sided stripsto connect panels 33.75 m
EEI-Int-RHC-01.1216
Uponor Radiant Heating/Cooling > Uponor pipe positioning panel Tecto
Uponor Tecto - System components and accessories
Uponor PE-Xa pipe
as coil, for use as radiant heating pipe, connected by Q&E, press or clamp
fittings.
Material: Uponor PE-Xa pipe made in high-pressure cross-linked
polyethylene (Engel method), conforming to DIN 16892 and DIN ISO
15875, oxygen-tight according to DIN 4726
Colour: white with black and red longitudinal stripes
Uponor PE-Xa pipe
Max. operating temperature: 90°C
Max. operating pressure: 6 bar at 70 °C
Application class: 4 / 6 bar
Item no. d [mm] s [mm] l [m] Description unit
1048290 14 2 240Uponor eval PE-Xa Q&E pipe 14x2.0240 m coil 240 m
1048291 14 2 640Uponor eval PE-Xa Q&E pipe 14x2.0640 m coil 640 m
Uponor eval PE-Xa Q&E pipe in coils
Pipes manufactured from peroxide cross-linked polyethylene (PE-Xa) using
the Engel method, complying with e.g. EN ISO 15875 ”Plastics piping
systems for hot and cold water installations - Cross-linked polyethylene”.
Includes an ethylene vinyl alcohol (EVOH) oxygen barrier layer, complying
with DIN 4726, to prevent corrosion of system components. This barrier
has been specially developed to work together with Uponor Q&E fitting
technology. Classification of service conditions (including typical field of
application): Application class 4 - Underfloor heating and low temperature
radiators, malfunction temperature 95 °C. Design pressure 6 bar.
Application class 5 - high temperature radiators, malfunction temperature
95 °C. Design pressure 6 bar.
Item no. d [mm] s [mm] l [m] p [bar] Description unit
1047610 16 2.0 120 6Uponor eval PE-Xa Q&E pipe16x2.0 mm in coils of 120 m 120 m
1047611 16 2.0 240 6Uponor eval PE-Xa Q&E pipe16x2.0 mm in coils of 240 m 240 m
1047612 16 2.0 640 6Uponor eval PE-Xa Q&E pipe16x2.0 mm in coils of 640 m 640 m
Uponor PE-Xa pipes
PE-Xa pipe with an oxygen diffusion barrier manufactured from peroxide
cross-linked polyethylene (PE-Xa) using the Engel method complying
with e.g. prENISO 15875 “Plastics piping systems for hot and cold water
installations - Cross-linked polyethylene” with an oxygen diffusion barrier
of EVOH (ethyl vinyl alcohol). Uponor pipes fulfil the requirements for
oxygen diffusion resistance as per DIN 4726. Malfunction temperature
95°C. Design pressure 8,8 bar (at 70°C).
Item no. d [mm] s [mm] l [m] V [l/m] Description unit
1034535 17 2.0 120 0.13Uponor pe PE-Xa Q&E pipe 17x2.0120 m coil 120 m
1009226 17 2.0 240 0.13Uponor pe PE-Xa Q&E pipe 17x2.0240 m coil 240 m
1009227 17 2.0 640 0.13Uponor pe PE-Xa Q&E pipe 17x2.0640 m coil 640 m
EEI-Int-RHC-01.12 17
Uponor Radiant Heating/Cooling > Uponor pipe positioning panel Tecto
Uponor Tecto - System components and accessories
Uponor MLCP white in coils
Diffusion-tight multi-layer composite pipe (PE-RT - adhesive -
longitudinally welded aluminium - adhesive - PE-RT) for distribution
conduits, rising mains and connection lines for plumbing, radiator
connection and fancoil connection. Fire classification E according to DIN
EN 13501-1. Pipe end caps as hygienic seal according EN 806.
Resistance of temperature:
Tap water: The maximum permanent operating temperature exists between
0°C and 70°C at a maximum permanent operating pressure of 10 bars. The
short-term malfunction temperature is 95°C of a maximum of 100 hours in
the operating lifetime.
Heating: The maximum permanent operating temperature is 80°C at
a maximum permanent operating pressure of 10 bars. The short-term
malfunction temperature is 95°C of a maximum of 150 hours in the
operating time per year.
Item no. d [mm] s [mm] l [m] Description unit
1013366 14 2.0 200Uponor MLCP 14x2white in coils 200m 200 m
1013378 16 2.0 100Uponor MLCP 16x2white in coils 100m 100 m
1013371 16 2.0 200Uponor MLCP 16x2white in coils 200m 200 m
1013380 16 2.0 500Uponor MLCP 16x2white in coils 500m 500 m
Uponor Q&E Coupling
for Uponor PEXa pipe consisting of:
1 Coupling / Brass
2 PEX-Rings for secure connection / cross linked Polyethylene
Item no. d [mm] Description unit
1058659 14Uponor Q&E Coupling 14with two eval Rings, nature 10 pcs
1058660 16Uponor Q&E Coupling 16with two eval Rings, nature 20 pcs
1058661 17Uponor Q&E Coupling 17with two eval Rings, nature 10 pcs
Uponor Q&E Ring natural
Made of PE-X. Uponor rings natural intended for Uponor Q&E fittings.
Item no. d [mm] colour [-] Description unit
1058428 14 naturalUponor Q&E ring eval without stop edgenature 14 20 pcs
1042389 16 naturalUponor Q&E Ring eval with stop edgenature 16 20 pcs
1058429 17 naturalUponor Q&E ring eval without stop edgenature 17 20 pcs
Uponor press coupling MLC up to 32
Made of tin-plated brass, with fixed press sleeve, stop ring, pressed
identification, colour code and test safety. Press without bevel.
Item no. d [mm] Description unit
1015154 14Uponor press coupling MLC 14-14
10 pcs
1015164 16Uponor press coupling MLC 16-16
10 pcs
EEI-Int-RHC-01.1218
Uponor Radiant Heating/Cooling > Uponor self attaching system
EEI-Int-RHC-01.12 19
Uponor self attaching system
With its self attaching system,
Uponor off ers installers an
innovating pipe laying system
for underfl oor heating pipes. At
the factory, hook fasting tape
is wound around the oxygen-
tight pipes conforming to
DIN 4726. The system insulat-
ing panel, which can also be used as a stapler panel, is completely
covered with the matching laminated loop foil. The pipe can be
reeled off and laid on the fl oor as usual and only needs to be
pressed at the correct position against the laminated insulating
panel. The hooks on the tape around the pipe catch the loops on
the foil and thus secure the pipe to the surface. Both the hook
take and the loop foil are designed to guarantee maximum fi xture.
Your advantages
Easy pipe laying without any special tools
For cost-effi cient one-man installation
Installed pipes can be repositioned at any time
System panels available in various thicknesses to suit indi-
vidual insulation needs
Roll-out insulation for fast installation
Ideal for fl exible pipe spacing in rooms of any shape
Thanks to the large number of fastening points, the pipe is
fi rmly placed against the surface along its entire length
System components
Uponor self attaching
insulation roll panel
Systempipe/-Fittings
Uponor PE-Xa
self attaching
pipe 16 x 1.8
Uponor MLCP
self attaching
pipe 16x2.0
Uponor self attaching
insulation fold panel
Uponor tape
Room controls
Uponor radio control
Uponor wired control 24 V
230 V components
Control stations
Uponor control stations - overview
20,5
Additional components
Uponor edging strip
Manifold/Cabinets
Uponor manifold
Uponor compression adapter
PE-Xa and MLCP
Uponor joint profi le
100x10
Uponor joint protection
20mm
Uponor marking set
Uponor screed
additive
Uponor PE foil 0.2 mm
Uponor cabinet
Uponor manifold connection
valve set G 1/Rp 1
MLC press coupling
16x2
Uponor PE-Xa Q&E coupling
Uponor Radiant Heating/Cooling > Uponor self attaching system
Uponor self attaching system - System components and accessories
Uponor self attaching insulation roll panel
Pipe fixing panel in roll form, for thermal and impact noise insulation
according to DIN EN 13163 and DIN 4108-10; made from EPS rigid foam
with laminated textile adhesive foil for overlap installation; foil extending
on one side to cover insulating layer according to DIN 18560.
Foil raster: 100 x 100 mm
DIN EN 13501-1 fire classification: class E
Item no. Description unit
1007226Uponor self attaching insulation roll panel 25-2EPS 045 DES SM 12 m²
1007228Uponor self attaching insulation roll panel 30-3EPS 045 DES SM 12 m²
Uponor self attaching insulation fold panel
Pipe fixing panel , for thermal and impact noise insulation according to DIN
EN 13163 and DIN 4108-10; made from EPS rigid foam with laminated
textile adhesive foil for overlap installation; foil extending on one side to
cover insulating layer according to DIN 18560.
Foil raster: 100 x 100 mm
DIN EN 13501-1 fire classification: class E
Item no. Description unit
1007232Uponor self attaching insulation fold panel 30-3
10 m²
Uponor self attaching insulation fold panel 15mm
Pipe fixing panel , for thermal insulation according to DIN EN 13163 and
DIN 4108-10; made from EPS rigid foam with laminated textile adhesive
foil for overlap installation; foil extending on one side to cover insulating
layer according to DIN 18560.
Foil raster: 100 x 100 mm
DIN EN 13501-1 fire classification: class E
Item no. Description unit
1007234Uponor self attaching insulation fold panel 15mmEPS 040 DEO 20 m²
Uponor tape
Tape for the sealed joining of Uponor insulation, applied with hand-held
roll device. Roll length 66m.
Item no. l [m] Description unit
1000012 66Uponor tape 50 mm
1 pcs
EEI-Int-RHC-01.1220
h [mm] l [mm] w [mm] G [kN/m²] R-value [m²K/W] Δ Lw [dB]
25-2 12000 1000 4 0.56 28
30-3 12000 1000 4 0.67 29
h [mm] l [mm] w [mm] G [kN/m²] R-value [m²K/W] Δ Lw [dB]
30-3 2000 1000 4 0.67 29
h [mm] l [mm] w [mm] G [kN/m²] R-value [m²K/W] Δ Lw [dB]
15 2000 1000 30 0.38 -
Uponor Radiant Heating/Cooling > Uponor self attaching system
Uponor self attaching system - System components and accessories
Uponor PE-Xa self attaching pipes
PE-Xa pipe with an oxygen diffusion barrier of EVOH manufactured from
peroxide cross-linked polyethylene (PE-Xa) using the Engel method
complying with DIN 16892 and DIN ISO 15875, oxygen tight according to
DIN 4726.
Max. operating temperature: 70°C
Application class 4 / 6 bar.
Item no. d [mm] s [mm] l [m] Description unit
1047624 16 1.8 240Uponor self attaching eval PE-Xa pipe 16x1.8240 m coil 240 m
1047625 16 1.8 640Uponor self attaching eval PE-Xa pipe 16x1.8640 m coil 640 m
Uponor MLCP UFH/C self attaching pipes
Diffusion-tight multi layer composite pipe (PE-RT - adhesive agent
- longitudinally welded aluminium - adhesive agent - PE-RT) for
radiant heating / cooling applications. Normally inflammable, materials
classification B2 according to DIN 4102. Max. continuous operation
pressure: 4 bar at continuous operating temperature 60°C.
Item no. d [mm] s [mm] l [m] Description unit
1048249 16 2 200Uponor MLCP self attaching red heating UFH/C 16x2.0200m pipe with oxygen barrier 200 m
1048395 16 2 500Uponor MLCP self attaching red heating UFH/C 16x2.0500m pipe with oxygen barrier 500 m
Uponor Q&E Coupling
for Uponor PEXa pipe consisting of:
1 Coupling / Brass
2 PEX-Rings for secure connection / cross linked Polyethylene
Item no. d [mm] Description unit
1058660 16Uponor Q&E Coupling 16with two eval Rings, nature 20 pcs
Uponor Q&E Ring natural
Made of PE-X. Uponor rings natural intended for Uponor Q&E fittings.
Item no. d [mm] colour [-] Description unit
1042389 16 naturalUponor Q&E Ring eval with stop edgenature 16 20 pcs
Uponor press coupling MLC up to 32
Made of tin-plated brass, with fixed press sleeve, stop ring, pressed
identification, colour code and test safety. Press without bevel.
Item no. d [mm] Description unit
1015164 16Uponor press coupling MLC 16-16
10 pcs
EEI-Int-RHC-01.12 21
Uponor Radiant Heating/Cooling > Uponor stapler and clamp track
EEI-Int-RHC-01.1222
Uponor stapler and clamp track system
All components of the Uponor
stapler and clamp track system
are designed to perfectly match
each other.
The panels with thermal and
impact noise insulation are
equipped with a tear-proof sur-
face and a printed installation
grid. They allow for easy installation of the system pipe. These and
all other components are designed to ensure optimum safety and
reliable operation of the system.
Your advantages
Flexible pipe laying
Available as composite panels or rolls with a range of diff er-
ent thermal and impact noise insulation layers
Suitable for all types of screeds
Large pipe coils reel for minimum cut-off s and twist-fee
installation
Fast to install thanks to the integrated insulation layer
cover
Universal staple nail for pipe thickness of 14 – 20 mm
Easy installation with ergonomically designed Uponor
system stapler
System components
Uponor insulation
roll
Systempipe/-Fittings
Uponor PE-Xa
pipe
Uponor MLCP
pipe
Uponor pipe staple nail
Uponor tape
Uponor clamp
track
Uponor fastening nail
Uponor stapler
Room controls
Uponor radio control
Uponor wired control 24 V
230 V components
Control stations
Uponor control stations - overview
20,5
Additional components
Uponor edging strip
Manifold/Cabinets
Uponor manifold
Uponor compression adapter
PE-Xa and MLCP
Uponor joint profi le
100x10
Uponor joint protection
20mm
Uponor marking set
Uponor screed
additive
Uponor PE foil 0.2 mm
Uponor cabinet
Uponor manifold connection
valve set G 1/Rp 1
Uponor PE-Xa Q&E coupling
MLC press coupling
14x2 + 16x2
+ 20x2,25
Uponor Radiant Heating/Cooling > Uponor stapler and clamp track
Uponor stapler and clamp track - System components and accessories
Uponor insulation roll panel with texture foil
Ready-to-lay heat/sound insulation roll, consisting of: tear-resistant
texture foil laminated onto 25-2 EPS 045 DES sm as per DIN EN 13163
and DIN V 4108-10 (WLG 045). DIN EN 13501-1 fire classification: class
E. Standard flammability, building-material class B2, conforming to DIN
4102. Suitable for use in area between floors, where rooms on either side
are heated to same level. With printed-on grid pattern for ease of cutting
and alignment. Approved for moving loads of up to 4.0 kN/m². Thermal
resistance: 0,56 (m² x K/W).
Item no. Description unit
1000002Uponor insulation roll panel with texture foiltyp 30-2 12 m²
1000003Uponor insulation roll panel with texture foiltyp 30-3 12 m²
Uponor PE pattern foil 0.25mm
0,25 mm-thick foil with printed on pattern 100 x 100 mm for laying over
existing heat/sound insulation and fixation of clamp tracks. Prevents
screed from flowing down into the insulating layer.
Dimensions: 100 m x 1.03 m
Item no. l [m] w [m] s [mm] Description unit
1000015 100 1.03 0.25Uponor PE pattern foil 0.25mm thicknessfor clamp track fixation 103 m²
Uponor pipe fixing foil
Multi-layer reflection and impact foil, designed to improve thermal
insulation and distribution; also serving as
damping course. With printed raster.
Load capacity: 15 kN/m2
Roll width: 1 m
Roll length: 60 m
Foil height: 4 mm
Item no. l [m] w [m] s [mm] G [kN/m²] Description unit
1000017 60 1 4 15Uponor pipe fixing foil 4 mm
60 m²
Uponor Pipe Clip standard
Pipe staple "Standard" in blue, loaded into magazine for securing heating-
system pipes onto insulation. For Uponor pipes 14 - 20 mm.
Item no. d [mm] Description unit
1002296 14-20Uponor Pipe Clip standardØ: 14-20 mm, H = 40 mm 1000 pcs
Uponor Pipe Clip long
Pipe staple "Long" in grey, loaded into magazine for securing heating-
system pipes onto insulation. For Uponor pipes 14 - 20 mm.
Item no. d [mm] Description unit
1002297 14-20Uponor Pipe Clip longØ: 14-20 mm, H = 55 mm 300 pcs
EEI-Int-RHC-01.12 23
h [mm] l [mm] w [mm] G [kN/m²] R-value [m²K/W] Δ Lw [dB]
30-2 12000 1000 5 0.75 28
30-3 12000 1000 4 0.67 29
Uponor Radiant Heating/Cooling > Uponor stapler and clamp track
Uponor stapler and clamp track - System components and accessories
ra
d
h
l b
Uponor clamp track 14
Self-adhesive U-profile strip made of recycled material, with integrated
pipe holder for 14 x 2 mm Uponor pipes. Rated break points are provided
every 100 mm for easy separation.
Length of track: 2.5 m
Width of track: 38 mm
Space between pipe holders: 50 mm c/c
Installation height with pipe: 17 mm
Item no. l [mm] w [mm] h [mm] d [mm] c/c [mm] Description unit
1005498 2500 38 17 14 50Uponor clamp track 14 mm
25 m
ra
d
h
l b
Uponor clamp track 16
Self-adhesive U-profile strip made of recycled material, with integrated
pipe holder for 16 x 2 mm Uponor pipes. Rated break points are provided
every 100 mm for easy separation.
Length of track: 2 m
Width of track: 40 mm
Space between pipe holders: 25 mm c/c
Installation height with pipe: 25 mm
Item no. l [mm] w [mm] h [mm] d [mm] c/c [mm] Description unit
1013127 2000 40 25 16 25Uponor clamp track 16 mm
100 m
Uponor clamp track 14-20
Self-adhesive U-profile strip made of recycled material, with integrated
pipe holder for Uponor pipes 14-20 mm.
Length of track: 1 m
Width of track: 50 mm
Space between pipe holders: 50 mm c/c
Installation height with pipe: 27 mm
Item no. l [mm] w [mm] h [mm] c/c [mm] Description unit
1000018 1000 50 27 50Uponor clamp track 14 - 20 mm
100 m
Uponor fastening nail
The purpose of the fastening nail is to fix the Uponor clamp track and
the fixing-foil or the pipe positioning panel to the underlaying layer of
insulation. Can also be used for additional manual fastening of Uponor
MLC and PE-Xa pipes.
Item no. Description unit
1000019Uponor fastening nail
500 pcs
EEI-Int-RHC-01.1224
Uponor Radiant Heating/Cooling > Uponor stapler and clamp track
Uponor stapler and clamp track - System components and accessories
Uponor PE-Xa pipe
as coil, for use as radiant heating pipe, connected by Q&E, press or clamp
fittings.
Material: Uponor PE-Xa pipe made in high-pressure cross-linked
polyethylene (Engel method), conforming to DIN 16892 and DIN ISO
15875, oxygen-tight according to DIN 4726
Colour: white with black and red longitudinal stripes
Uponor PE-Xa pipe
Max. operating temperature: 90°C
Max. operating pressure: 6 bar at 70 °C
Application class: 4 / 6 bar
Item no. d [mm] s [mm] l [m] Description unit
1048290 14 2 240Uponor eval PE-Xa Q&E pipe 14x2.0240 m coil 240 m
1048291 14 2 640Uponor eval PE-Xa Q&E pipe 14x2.0640 m coil 640 m
Uponor eval PE-Xa Q&E pipe in coils
Pipes manufactured from peroxide cross-linked polyethylene (PE-Xa) using
the Engel method, complying with e.g. EN ISO 15875 ”Plastics piping
systems for hot and cold water installations - Cross-linked polyethylene”.
Includes an ethylene vinyl alcohol (EVOH) oxygen barrier layer, complying
with DIN 4726, to prevent corrosion of system components. This barrier
has been specially developed to work together with Uponor Q&E fitting
technology. Classification of service conditions (including typical field of
application): Application class 4 - Underfloor heating and low temperature
radiators, malfunction temperature 95 °C. Design pressure 6 bar.
Application class 5 - high temperature radiators, malfunction temperature
95 °C. Design pressure 6 bar.
Item no. d [mm] s [mm] l [m] p [bar] Description unit
1047610 16 2.0 120 6Uponor eval PE-Xa Q&E pipe16x2.0 mm in coils of 120 m 120 m
1047611 16 2.0 240 6Uponor eval PE-Xa Q&E pipe16x2.0 mm in coils of 240 m 240 m
1047612 16 2.0 640 6Uponor eval PE-Xa Q&E pipe16x2.0 mm in coils of 640 m 640 m
Uponor PE-Xa pipes
PE-Xa pipe with an oxygen diffusion barrier manufactured from peroxide
cross-linked polyethylene (PE-Xa) using the Engel method complying
with e.g. prENISO 15875 “Plastics piping systems for hot and cold water
installations - Cross-linked polyethylene” with an oxygen diffusion barrier
of EVOH (ethyl vinyl alcohol). Uponor pipes fulfil the requirements for
oxygen diffusion resistance as per DIN 4726. Malfunction temperature
95°C. Design pressure 8,8 bar (at 70°C).
Item no. d [mm] s [mm] l [m] V [l/m] Description unit
1034535 17 2.0 120 0.13Uponor pe PE-Xa Q&E pipe 17x2.0120 m coil 120 m
1009226 17 2.0 240 0.13Uponor pe PE-Xa Q&E pipe 17x2.0240 m coil 240 m
1009227 17 2.0 640 0.13Uponor pe PE-Xa Q&E pipe 17x2.0640 m coil 640 m
1009228 20 2.0 120 0.2Uponor pe PE-Xa Q&E pipe 20x2.0120 m coil 120 m
1009230 20 2.0 240 0.2Uponor pe PE-Xa Q&E pipe 20x2.0240 m coil 240 m
1009231 20 2.0 480 0.2Uponor pe PE-Xa Q&E pipe 20x2.0480 m coil 480 m
EEI-Int-RHC-01.12 25
Uponor Radiant Heating/Cooling > Uponor stapler and clamp track
Uponor stapler and clamp track - System components and accessories
Uponor MLCP white in coils
Diffusion-tight multi-layer composite pipe (PE-RT - adhesive -
longitudinally welded aluminium - adhesive - PE-RT) for distribution
conduits, rising mains and connection lines for plumbing, radiator
connection and fancoil connection. Fire classification E according to DIN
EN 13501-1. Pipe end caps as hygienic seal according EN 806.
Resistance of temperature:
Tap water: The maximum permanent operating temperature exists between
0°C and 70°C at a maximum permanent operating pressure of 10 bars. The
short-term malfunction temperature is 95°C of a maximum of 100 hours in
the operating lifetime.
Heating: The maximum permanent operating temperature is 80°C at
a maximum permanent operating pressure of 10 bars. The short-term
malfunction temperature is 95°C of a maximum of 150 hours in the
operating time per year.
Item no. d [mm] s [mm] l [m] Description unit
1013366 14 2.0 200Uponor MLCP 14x2white in coils 200m 200 m
1013371 16 2.0 200Uponor MLCP 16x2white in coils 200m 200 m
1013378 16 2.0 100Uponor MLCP 16x2white in coils 100m 100 m
1013380 16 2.0 500Uponor MLCP 16x2white in coils 500m 500 m
1013392 20 2.25 200Uponor MLCP 20x2,25white in coils 200m 200 m
Uponor Q&E Coupling
for Uponor PEXa pipe consisting of:
1 Coupling / Brass
2 PEX-Rings for secure connection / cross linked Polyethylene
Item no. d [mm] Description unit
1058659 14Uponor Q&E Coupling 14with two eval Rings, nature 10 pcs
1058660 16Uponor Q&E Coupling 16with two eval Rings, nature 20 pcs
1058661 17Uponor Q&E Coupling 17with two eval Rings, nature 10 pcs
1058668 20Uponor Q&E Coupling 20with two eval Rings, nature 10 pcs
Uponor Q&E Ring natural
Made of PE-X. Uponor rings natural intended for Uponor Q&E fittings.
Item no. d [mm] colour [-] Description unit
1058428 14 naturalUponor Q&E ring eval without stop edgenature 14 20 pcs
1042389 16 naturalUponor Q&E Ring eval with stop edgenature 16 20 pcs
1058429 17 naturalUponor Q&E ring eval without stop edgenature 17 20 pcs
1042837 20 naturalUponor Q&E Ring eval with stop edgenature 20 20 pcs
Uponor press coupling MLC up to 32
Made of tin-plated brass, with fixed press sleeve, stop ring, pressed
identification, colour code and test safety. Press without bevel.
Item no. d [mm] Description unit
1015154 14Uponor press coupling MLC 14-14
10 pcs
1015164 16Uponor press coupling MLC 16-16
10 pcs
1015187 20Uponor press coupling MLC 20-20
10 pcs
EEI-Int-RHC-01.1226
Uponor Radiant Heating/Cooling > Uponor pipe positioning panel
EEI-Int-RHC-01.12 27
Uponor pipe positioning panel 14-16
The Uponor installation panel
has been specially developed
for the installation of under-
fl oor heating/cooling systems
in residential and non-residen-
tial buildings. The panels are
installed in the fl oor below the
cement or anhydrite screed
load distribution layer. Uponor installation panels are available in
two diff erent thicknesses with insulation (ND30-2) and without
insulation (ND11), catering for various fl oor constructions and
load-bearing requirements.
Your advantages
Cost-effi cient one-man installation
Easy laying thanks to large panels (1447 x 900 mm)
Compensation elements for doors, movements joints and
wall joints available
Suitable pipe sizes from 14 to 16 mm
Ensures standardised pipe spacing due to forced pipe paths
Proper covering of the insulating layer thanks to integrated
sturdy deep-drawn foil
Suitable for a wide range of applications thanks to high
strength properties (ND 30-2: 5 kN/m²; ND 11: 30 kN/
m²)
System components Systempipe/-Fittings
Uponor PE-Xa
pipe
Room controls
Uponor radio control
Uponor wired control 24 V
230 V components
Control stations
Uponor control stations - overview
20,5
Additional components
Uponor edging strip
Manifold/Cabinets
Uponor manifold
Uponor compression adapter
PE-Xa and MLCP
Uponor joint profi le
100x10
Uponor joint protection
20mm
Uponor marking set
Uponor screed
additive
Uponor PE foil 0.2 mm
Uponor cabinet
Uponor manifold connection
valve set G 1/Rp 1
Uponor Q&E coupling
MLCP pipe
14 + 16
MLC press coupling
14x2 + 16x2
Uponor installation panel
14-16 ND11
Uponor installation panel
14-16 ND
Uponor pipe positioning
panel
Uponor Radiant Heating/Cooling > Uponor pipe positioning panel
Uponor pipe positioning panel - System components and accessories
Uponor installation foil 14-16
Foil element without foamed back panel. Vacuum-formed PS deep-drawn
foil made of impact-proof polystyrene with integrated pipe fixing studs for
proper pipe spacing and exact installation of the Uponor system pipes at
the required height. The deep-drawn foil overlaps on two sides; when laid
in a staggered pattern, the foil layer is thus continuous. For installation on
top of insulation layer.
Right-angled: RA 5.5 – 11 – 16,5 – 22 – 27.5 – 33 cm
Diagonal: RA 7.5 – 15 – 22.5 – 30 cm
Dimensions of element foil: 1447 x 900 m
Item no. h1 [mm] l [mm] w [mm] A [m²] Δ Lw [dB] Description unit
1016703 18 1447 900 1.2 0Uponor pipe positioning panel14 - 16 mm 10 m²
Uponor installation panel 14-16 / 30-2
For cement and self-levelling cement screeds; allows for right-angled or
diagonal pipe installation at 6 plus 4 different pipe distances; for optimised
heating pipe installation based on actual room geometry with minimum
cut-offs thanks to sophisticated system technology; allows for fast and
easy installation of the hard/soft PS rigid foam panels with overlapping
foil edges. Meets the requirements for standard impact noise insulation
(DIN 4109), thermal insulation (DIN EN1264), DIN EN 13501-1 fire
classification: class E, fire safety (DIN 4102) B2 and heat output (DIN EN
1264), irrespective of the pipe spacing; the height and distance of the
sturdy pipe holders (DIN EN 1264) are fixed to prevent shifting of the
pipes; the overlapping application foil acts as a damp-proofing course and
eliminates sound bridges (DIN 18560); protects the environment thanks to
use of environmentally friendly PS. Properties subject to continuous RAL
quality monitoring.
Pipe spacing with right-angle installation: RA 5.5 - 11 - 16.5 - 22 - 27.5
- 33 cm
Pipe spacing with diagonal installation: RA 7.5 - 15 - 22.5 - 30 cm
Type: 30-2 mm, for universal use in
residential and commercial buildings up to 5 kN/m2
EPS 040 DES sg
Dimensions: 1447 x 900 mm
Plate thickness: 48 mm
Impact noise insulation: 28 dB
Application range: up to 5 kN/m2
Thermal resistance: R� = 0.75 m2K/W
Item no. h1 [mm] h2 [mm] l [mm] w [mm] A [m²] Δ Lw [dB] Description unit
1016699 50/48 30-2 1447 900 1.2 28Uponor nap panel 14-16mm incl.Insulation, thickness 30mm 10 m²
EEI-Int-RHC-01.1228
Uponor Radiant Heating/Cooling > Uponor pipe positioning panel
Uponor pipe positioning panel - System components and accessories
Uponor installation panel 14-16 / 11
For cement and self-levelling cement screeds; allows for right-angled or
diagonal pipe installation at 6 plus 4 different pipe distances; for optimised
heating pipe installation based on actual room geometry with minimum
cut-offs thanks to sophisticated system technology; allows for fast and
easy installation of the hard/soft PS rigid foam panels with overlapping
foil edges. Meets the requirements for standard impact noise insulation
(DIN 4109), thermal insulation (DIN EN1264), DIN EN 13501-1 fire
classification: class E, fire safety (DIN 4102) B2 and heat output (DIN EN
1264), irrespective of the pipe spacing; the height and distance of the
sturdy pipe holders (DIN EN 1264) are fixed to prevent shifting of the
pipes; the overlapping application foil acts as a damp-proofing course and
eliminates sound bridges (DIN 18560); protects the environment thanks to
use of environmentally friendly PS. Properties subject to continuous RAL
quality monitoring.
Pipe spacing with right-angle installation: RA 5.5 - 11 - 16.5 - 22 - 27.5
- 33 cm
Pipe spacing with diagonal installation: RA 7.5 - 15 - 22.5 - 30 cm
Type: 11 mm, for universal use in
residential and commercial buildings up to 30 kN/m2
EPS 035 DE0 dm (100kPa)
Dimensions: 1447 x 900 mm
Plate thickness: 29 mm
Application range: up to 30 kN/m2
Item no. h1 [mm] h2 [mm] l [mm] w [mm] A [m²] Δ Lw [dB] Description unit
1016700 29 11 1447 900 1.2 0Uponor nap panel 14-16mm incl.Insulation, thickness 11mm 10 m²
Uponor installation panel 14-16 manifold/door kit
30-2
For universal use, facilitating pipe laying near manifolds thanks to special
manifold element. Stud overlap allows for easy integration into element
structure. Door element designed for straight door openings; can be cut
into customised door element strips. Per panel, you can cut 10 strips
catering for 5 doors. Universal use of element thanks to easy adjustment
to complex
room geometries including angled door openings.
Type: 30-2 VT
EPS 040 DES sg
Dimensions: 1447 x 900 mm
Application range: up to 5 kN/m2
consisting of:
2.5 m2 manifold element foil (2 panels)
2.5 m2 door element foil (2 panels)
5 m2 30-2 mm thermal and impact noise insulation (4 panels)
Item no. h1 [mm] h2 [mm] l [mm] w [mm] A [m²] Δ Lw [dB] Description unit
1016701 50/48 30-2 1420 900 1.2 28Uponor manifold-/door set for nap panel 14-16mmthickness 30mm 5 m²
EEI-Int-RHC-01.12 29
Uponor Radiant Heating/Cooling > Uponor pipe positioning panel
Uponor pipe positioning panel - System components and accessories
For universal use, facilitating pipe laying near manifolds thanks to special
manifold element. Stud overlap allows for easy integration into element
structure. Door element designed for straight door openings; can be cut
into customised door element strips. Per panel, you can cut 10 strips
catering for 5 doors. Universal use of element thanks to easy adjustment
to complex
room geometries including angled door openings.
Type: 11 VT
EPS 035 DEO dm (100 kPa)
Dimensions: 1447 x 900 mm
Application range: up to 30 kN/m2
consisting of:
2.5 m2 manifold element foil (2 panels)
2.5 m2 door element foil (2 panels)
5 m2 11mm thermal insulation (4 panels)
Item no. h1 [mm] h2 [mm] l [mm] w [mm] A [m²] Δ Lw [dB] Description unit
1016702 29 11 1420 900 1.2 0Uponor manifold-/door set for nap panel 14-16mmthickness 11mm 5 m²
Uponor PE-Xa pipe
as coil, for use as radiant heating pipe, connected by Q&E, press or clamp
fittings.
Material: Uponor PE-Xa pipe made in high-pressure cross-linked
polyethylene (Engel method), conforming to DIN 16892 and DIN ISO
15875, oxygen-tight according to DIN 4726
Colour: white with black and red longitudinal stripes
Uponor PE-Xa pipe
Max. operating temperature: 90°C
Max. operating pressure: 6 bar at 70 °C
Application class: 4 / 6 bar
Item no. d [mm] s [mm] l [m] Description unit
1048290 14 2 240Uponor eval PE-Xa Q&E pipe 14x2.0240 m coil 240 m
1048291 14 2 640Uponor eval PE-Xa Q&E pipe 14x2.0640 m coil 640 m
Uponor eval PE-Xa Q&E pipe in coils
Pipes manufactured from peroxide cross-linked polyethylene (PE-Xa) using
the Engel method, complying with e.g. EN ISO 15875 ”Plastics piping
systems for hot and cold water installations - Cross-linked polyethylene”.
Includes an ethylene vinyl alcohol (EVOH) oxygen barrier layer, complying
with DIN 4726, to prevent corrosion of system components. This barrier
has been specially developed to work together with Uponor Q&E fitting
technology. Classification of service conditions (including typical field of
application): Application class 4 - Underfloor heating and low temperature
radiators, malfunction temperature 95 °C. Design pressure 6 bar.
Application class 5 - high temperature radiators, malfunction temperature
95 °C. Design pressure 6 bar.
Item no. d [mm] s [mm] l [m] p [bar] Description unit
1047610 16 2.0 120 6Uponor eval PE-Xa Q&E pipe16x2.0 mm in coils of 120 m 120 m
1047611 16 2.0 240 6Uponor eval PE-Xa Q&E pipe16x2.0 mm in coils of 240 m 240 m
1047612 16 2.0 640 6Uponor eval PE-Xa Q&E pipe16x2.0 mm in coils of 640 m 640 m
EEI-Int-RHC-01.1230
Uponor installation panel 14-16 manifold/door kit
11
Uponor Radiant Heating/Cooling > Uponor pipe positioning panel
Uponor pipe positioning panel - System components and accessories
Uponor MLCP white in coils
Diffusion-tight multi-layer composite pipe (PE-RT - adhesive -
longitudinally welded aluminium - adhesive - PE-RT) for distribution
conduits, rising mains and connection lines for plumbing, radiator
connection and fancoil connection. Fire classification E according to DIN
EN 13501-1. Pipe end caps as hygienic seal according EN 806.
Resistance of temperature:
Tap water: The maximum permanent operating temperature exists between
0°C and 70°C at a maximum permanent operating pressure of 10 bars. The
short-term malfunction temperature is 95°C of a maximum of 100 hours in
the operating lifetime.
Heating: The maximum permanent operating temperature is 80°C at
a maximum permanent operating pressure of 10 bars. The short-term
malfunction temperature is 95°C of a maximum of 150 hours in the
operating time per year.
Item no. d [mm] s [mm] l [m] Description unit
1013366 14 2.0 200Uponor MLCP 14x2white in coils 200m 200 m
1013378 16 2.0 100Uponor MLCP 16x2white in coils 100m 100 m
1013371 16 2.0 200Uponor MLCP 16x2white in coils 200m 200 m
1013380 16 2.0 500Uponor MLCP 16x2white in coils 500m 500 m
Uponor Q&E Coupling
for Uponor PEXa pipe consisting of:
1 Coupling / Brass
2 PEX-Rings for secure connection / cross linked Polyethylene
Item no. d [mm] Description unit
1058659 14Uponor Q&E Coupling 14with two eval Rings, nature 10 pcs
1058660 16Uponor Q&E Coupling 16with two eval Rings, nature 20 pcs
Uponor Q&E Ring natural
Made of PE-X. Uponor rings natural intended for Uponor Q&E fittings.
Item no. d [mm] colour [-] Description unit
1058428 14 naturalUponor Q&E ring eval without stop edgenature 14 20 pcs
1042389 16 naturalUponor Q&E Ring eval with stop edgenature 16 20 pcs
Uponor press coupling MLC up to 32
Made of tin-plated brass, with fixed press sleeve, stop ring, pressed
identification, colour code and test safety. Press without bevel.
Item no. d [mm] Description unit
1015154 14Uponor press coupling MLC 14-14
10 pcs
1015164 16Uponor press coupling MLC 16-16
10 pcs
EEI-Int-RHC-01.12 31
Uponor Radiant Heating/Cooling > Uponor steel mesh Classic
EEI-Int-RHC-01.1232
Uponor steel mesh system Classic
The Uponor steel mesh system
Classic is the ideal solution for
underfl oor heating/cooling
systems on virtually all fl oors
in new residential and com-
mercial buildings.
Available in three raster sizes,
Uponor Classic allows you to
optimise the pipe spacing to meet the actual heating needs. As
the heating layer is separated from the insulation layer(s), the
system, in combination with high-payload insulation, is also ide-
ally suited for areas with high traffi c and payload, such as garage
showrooms, production halls, retail outlets, etc.
Your advantages
Exact pipe laying: the steel mesh and pipe holders ensure
standardized pipe distances – along both horizontal and
vertical.
Sturdy clamping: the pipe clips secure the pipe fi rmly on
the carrier element.
No damage to insulation covering
Free hand when choosing your insulating material.
Cost-effi cient one-man installation: fl exible, fast and easy
to install, saving you time and money.
System components
Uponor steel mesh
Systempipe/-Fittings
Uponor PE-Xa pipe
17x2,0 + 20x2,0
Uponor Q&E couplingUponor PE Foil 0.2mm
PE-type 200
Uponor calbe tie
Uponor tying wire
Uponor pipe holder clip
Room controls
Uponor radio control
Uponor wired control 24 V
230 V components
Control stations
Uponor control stations - overview
20,5
Additional components
Uponor edging strip
Manifold/Cabinets
Uponor manifold
Uponor joint profi le
100x10
Uponor compression adapter
PE-Xa and MLCP
Uponor joint protection
20mm
Uponor marking set
Uponor screed
additive
Uponor PE foil 0.2 mm
Uponor cabinet
Uponor manifold connection
valve set G 1/Rp 1
e.g. can be used with Knauf Floor Screed FE 80
Uponor Radiant Heating/Cooling > Uponor steel mesh Classic
Uponor Classic - System components and accessories
Uponor Classic steel mesh
For stable attachment of pipe fixations and standard installation of
underfloor heating pipes. Dim. 2100mm x 1200mm.
Material: corrosion protected steel.
Item no. l [mm] w [mm] d [mm] r [mm] A [m²] Description unit
1005084 2100 1200 3 100 2.5Uponor Classic element 10cmgrid 10 and 20, corrosion protected 25 m²
1005087 2100 1200 3 150 2.5Uponor Classic element 15cmgrid 15 and 30, corrosion protected 25 m²
Uponor PE foil 0.2mm
For installation on Uponor insulation or on standardised insulating material
approved for the intended purpose for areas without stud foil. Prevents
screed penetrating the underlying insulation.
Dimensions: 4 m x 2.5 m
Thickness: 0.2 mm
Item no. l [m] w [m] s [mm] Description unit
1005049 60 1.25 ~0.2Uponor PE foil 0.2 mm thickness60 x 1.25 m 75 m²
Uponor pipe fixing foil
Multi-layer reflection and impact foil, designed to improve thermal
insulation and distribution; also serving as
damping course. With printed raster.
Load capacity: 15 kN/m2
Roll width: 1 m
Roll length: 60 m
Foil height: 4 mm
Item no. l [m] w [m] s [mm] G [kN/m²] Description unit
1000017 60 1 4 15Uponor pipe fixing foil 4 mm
60 m²
Uponor pipe holder clip
Plastic clip for fixation of 15-20mm pipes on steel mesh below or equal
6mm.
Item no. Description
1044181Uponor pipe holder clip for pipes 15-20mmon steel mesh below or equal 6mm 100 pcs
Uponor tying wire
For fastening Uponor pipes on reinforcement steel meshes. Made of steel.
250 pcs per bag.
Item no. Description unit
1009222Uponor tying wire, 150 x 1.25
250 pcs
Uponor cable tie
For fastening Uponor pipes on reinforcement steel meshed.
Made of polyamide.
Item no. w [mm] l [mm] Description unit
1005287 5 200Uponor cable ties, length 200 mmfor the pipe assembly on support mats 100 pcs
EEI-Int-RHC-01.12 33
Uponor Radiant Heating/Cooling > Uponor steel mesh Classic
Uponor Classic - System components and accessories
Uponor PE-Xa pipes
PE-Xa pipe with an oxygen diffusion barrier manufactured from peroxide
cross-linked polyethylene (PE-Xa) using the Engel method complying
with e.g. prENISO 15875 “Plastics piping systems for hot and cold water
installations - Cross-linked polyethylene” with an oxygen diffusion barrier
of EVOH (ethyl vinyl alcohol). Uponor pipes fulfil the requirements for
oxygen diffusion resistance as per DIN 4726. Malfunction temperature
95°C. Design pressure 8,8 bar (at 70°C).
Item no. d [mm] s [mm] l [m] V [l/m] Description unit
1034535 17 2.0 120 0.13Uponor pe PE-Xa Q&E pipe 17x2.0120 m coil 120 m
1009226 17 2.0 240 0.13Uponor pe PE-Xa Q&E pipe 17x2.0240 m coil 240 m
1009227 17 2.0 640 0.13Uponor pe PE-Xa Q&E pipe 17x2.0640 m coil 640 m
1009228 20 2.0 120 0.2Uponor pe PE-Xa Q&E pipe 20x2.0120 m coil 120 m
1009230 20 2.0 240 0.2Uponor pe PE-Xa Q&E pipe 20x2.0240 m coil 240 m
1009231 20 2.0 480 0.2Uponor pe PE-Xa Q&E pipe 20x2.0480 m coil 480 m
Uponor Q&E Coupling
for Uponor PEXa pipe consisting of:
1 Coupling / Brass
2 PEX-Rings for secure connection / cross linked Polyethylene
Item no. d [mm] Description unit
1058661 17Uponor Q&E Coupling 17with two eval Rings, nature 10 pcs
1058668 20Uponor Q&E Coupling 20with two eval Rings, nature 10 pcs
Uponor Q&E Ring natural
Made of PE-X. Uponor rings natural intended for Uponor Q&E fittings.
Item no. d [mm] colour [-] Description unit
1058429 17 naturalUponor Q&E ring eval without stop edgenature 17 20 pcs
1042837 20 naturalUponor Q&E Ring eval with stop edgenature 20 20 pcs
EEI-Int-RHC-01.1234
Uponor Radiant Heating/Cooling > Uponor Plaster Ceiling Cooling
EEI-Int-RHC-01.12 35
When it comes to managing
room temperature with comfort
and cost in mind, the Uponor
plaster system is truly multital-
ented as it can be used in ceil-
ings or walls and for cooling as
well as heating.
Your advantages
Minimum installation height
A universal system for ceilings and walls mounting
Very few, optimally interacting system components
Choice of preference for decades Uponor PE-Xa pipe
9,9 x 1,1 mm
Q&E fi tting system for fast,economical installation
Quick reaction time thanks to slim plaster coverage
Saves energy thanks to optimum operating temperatures
Uponor
clamp track
Uponor
PE-Xa pipe
9,9 x 1,1
Uponor PE-Xa pipe
20x2
Uponor Q&E
T-reducer 20/9,9/20
Uponor Q&E
jointing reducer 9,9/20
Uponor plaster ceiling cooling system
Systempipe/-Fittings Additional componentsSystem components
Uponor Minitec
coupling 9,9
Uponor Minitec expander
tool
Room controls
Uponor radio control
Uponor wired control 24 V
230 V components
Control stations
Uponor control stations - overview
20,5
Manifold/Cabinets
Uponor manifold
Uponor compression adapter
PE-Xa and MLCP
Uponor cabinet
Uponor manifold connection
valve set G 1/Rp 1
e.g. can be used with Knauf MP 75 Projection Plaster
Uponor Radiant Heating/Cooling > Uponor Plaster Ceiling Cooling
Uponor Plaster Wall/Ceiling H/C - System components and accessories
ra
d
h
l b
Uponor clamp track 9.9
Self-adhesive U-profile strip made of recycled material, with integrated
pipe holder for 9.9 x 1.1 mm Uponor PE-Xa pipes.
Length of track: 2.5 m
Width of track: 24 mm
Space between pipe holders: 20 mm c/c
Installation height with pipe: 13 mm
Item no. l [mm] w [mm] h [mm] d [mm] c/c [mm] Description unit
1005274 2500 24 13 10 20Uponor clamp track 9.9 mm
25 m
Uponor PE-Xa pipes
PE-Xa pipe with an oxygen diffusion barrier manufactured from peroxide
cross-linked polyethylene (PE-Xa) using the Engel method complying
with e.g. prENISO 15875 “Plastics piping systems for hot and cold water
installations - Cross-linked polyethylene” with an oxygen diffusion barrier
of EVOH (ethyl vinyl alcohol). Uponor pipes fulfil the requirements for
oxygen diffusion resistance as per DIN 4726. Malfunction temperature
95°C. Design pressure 8,8 bar (at 70°C).
Item no. d [mm] s [mm] l [m] V [l/m] Description unit
1033024 9.9 1.1 120 0.047Uponor eval PE-Xa pipe 9.9x1.1
120 m
1033026 9.9 1.1 240 0.047Uponor eval PE-Xa pipe 9.9x1.1
240 m
1033025 9.9 1.1 480 0.047Uponor eval PE-Xa pipe 9.9x1.1
480 m
Uponor PE-Xa pipes
PE-Xa pipe with an oxygen diffusion barrier manufactured from peroxide
cross-linked polyethylene (PE-Xa) using the Engel method complying
with e.g. prENISO 15875 “Plastics piping systems for hot and cold water
installations - Cross-linked polyethylene” with an oxygen diffusion barrier
of EVOH (ethyl vinyl alcohol). Uponor pipes fulfil the requirements for
oxygen diffusion resistance as per DIN 4726. Malfunction temperature
95°C. Design pressure 8,8 bar (at 70°C).
Item no. d [mm] s [mm] l [m] V [l/m] Description unit
1009228 20 2.0 120 0.2Uponor pe PE-Xa Q&E pipe 20x2.0120 m coil 120 m
1009230 20 2.0 240 0.2Uponor pe PE-Xa Q&E pipe 20x2.0240 m coil 240 m
1009231 20 2.0 480 0.2Uponor pe PE-Xa Q&E pipe 20x2.0480 m coil 480 m
Uponor PE-Xa Q&E coupling 9.9
For Uponor PE-Xa pipe 9.9 x 1.1 mm, consisting of:
- 1 coupling
- 2 PEX Q&E rings for secure connection
Material: Coupling made in brass; PEX Q&E rings made in high-pressure
cross-linked polyethylene
Item no. d [mm] s [mm] l [mm] z [mm] Description unit
1005264 9.9 1.1 34 4Uponor PE-Xa Q&E coupling 9.9-9.9with two PEX rings 10 pcs
EEI-Int-RHC-01.1236
Uponor Radiant Heating/Cooling > Uponor Plaster Ceiling Cooling
Uponor Plaster Wall/Ceiling H/C - System components and accessories
Uponor PE-Xa Q&E jointing reducer 20x9.9
For connection of Uponor PE-Xa pipes, made of brass.
Item no. d [mm] d1 [mm] Description unit
1020518 9.9 20Uponor PE-Xa Q&E jointing reducer 20 x 9.9incl. 1 PEX ring 9.9 and 1 PEX ring 20 5 pcs
Uponor PE-Xa Q&E tee reducer 20x9.9x20
For connection of Uponor PE-Xa pipes, made of brass.
Item no. d [mm] d1 [mm] d2 [mm] Description unit
1020524 20 9.9 20Uponor PE-Xa Q&E tee reducer 20 X 9.9 X 9.9incl. 1 PEX ring 9.9 and 2 PEX rings 20 5 pcs
Uponor PE-Xa conversion nipple
For Uponor PE-Xa pipes 9.9 x 1.1 mm, made of brass.
Item no. d [mm] MT ["] l [mm] z [mm] A/F [mm] Description unit
1005265 9.9 R 1/2 39 14 22Uponor PE-Xa conversion nipple9.9 - 1/2 with one PEX ring 10 pcs
Uponor Q&E Ring natural
Made of PE-X. Uponor rings natural intended for Uponor Q&E fittings.
Item no. d [mm] colour [-] Description unit
1042837 20 naturalUponor Q&E Ring eval with stop edgenature 20 20 pcs
Uponor PE-X ring for PE-Xa pipes
For Uponor Minitec PE-Xa pipe 9.9 x 1.1 mm; to secure fixing to Minitec
fittings
Material: High-pressure cross-linked polyethylene (PE-Xa)
Item no. d [mm] Description unit
1005263 9.9Uponor PE-X ring for PE-Xa pipes9.9 x 1.1 10 pcs
EEI-Int-RHC-01.12 37
Uponor Radiant Heating/Cooling > Uponor heat emission plate
Uponor heat emission plate
Uponor heat emission plate 17mm
Made of aluminium for use with timber suspended floors, with joists at
200mm centres. For support of Uponor PE-Xa pipes 17x2mm.
Item no. l [mm] w [mm] Description unit
1009129 1150 190Uponor heat emission plate 17 mm1150 x 190 mm 60 pcs
Uponor heat emission plate 20mm
Made of aluminium for use with timber suspended floors, with joists at
300mm centres. For support of Uponor PE-Xa pipes 20x2mm. Each pack of
40 plates covers 16m² (based on 80% floor coverage).
Item no. l [mm] w [mm] Description unit
1009132 1150 280Uponor heat emission plate 20 mm1150 x 280 mm 40 pcs
EEI-Int-RHC-01.1238
Uponor Radiant Heating/Cooling > Uponor underfloor heating accessories
Uponor under� oor heating accessories
Uponor edging strip 150x8
Edging strip conforming to DIN 18560, made of polyethylene with self-
adhesive strip on outer face provides tight seal between edging strip and
insulation. Length of roll: 50 m
Item no. h [mm] s [mm] l [m] Description unit
1000079 150 8 50Uponor edging strip 150x8in length of 50 m 200 m
Uponor edging strip 150x10
For installation between screed and adjacent building parts for floor
constructions according to DIN 18560 and DIN EN 1264; with multiple
tear perforation, laminated PE foil, self-adhesive sealing strips, particularly
suitable for self-levelling screeds; bottom side adhesive for attachment to
wall and exact installation in wall corners
Material: Closed-cell polyethylene PE-LD
Building material class: B2
Colour: blue
Item no. h [mm] s [mm] l [m] colour [-] Description unit
1000080 150 10 50 blueUponor edging strip 150x10in length of 50 m 200 m
Uponor joint profile 100x10
Self-adhesive clamp-on profile element made of hard PVC with
polyethylene foam expansion strip, 10 mm thick, for the reliable separation
of screed sections (e.g. in doorways), and to absorb expansion of screed.
For expansion joints as per DIN 18560-2.
Height: 100 mm
Material thickness: 10 mm
Length: 2 m
Item no. h [mm] s [mm] l [m] Description unit
1000081 100 10 2Uponor joint profile/self-adhesive striplength 2 m, height 100mm, thickness 10mm 30 m
Uponor joint protection 20mm
Made of PE-LD, with slit opening, for protection of pipes up to 20 mm in
areas of expansion joints.
Length: 300 mm
Item no. l [mm] w [mm] s [mm] Description unit
1000082 300 80 5Uponor joint protection tube for pipesup to 20 mm 30 pcs
EEI-Int-RHC-01.12 39
Uponor Radiant Heating/Cooling > Uponor underfloor heating accessories
Uponor under� oor heating accessories
l
b
s
Uponor joint protection 9.9mm
Made of PE-LD, with slit opening, for protection of pipes up to 9.9 mm in
areas of expansion joints.
Length: 300 mm
Item no. l [mm] s [mm] w [mm] Description unit
1005269 300 2 35Uponor joint protection tube forPE-Xa pipes 9.9 x 1.1, length 300 mm 30 pcs
Uponor PE foil 0.2mm
For installation on Uponor insulation or on standardised insulating material
approved for the intended purpose for areas without stud foil. Prevents
screed penetrating the underlying insulation.
Dimensions: 4 m x 2.5 m
Thickness: 0.2 mm
Item no. l [m] w [m] s [mm] Description unit
1005049 60 1.25 ~0.2Uponor PE foil 0.2 mm thickness60 x 1.25 m 75 m²
Uponor foil plug
For fixing the foil on insulation. Lenght: 25 mm
Item no. l [mm] Description unit
1000016 25Uponor foil plug l=25mm
100 pcs
Uponor marking kit
For the marking of a measuring point for dampness measurement in screed,
with red marker end. The marker is secured according to DIN 18560 with
adhesive tape to the cover layer. The cover layer is not destroyed by the
marker. A minimum distance from the measuring point to the nearest
heating pipe of 10 cm must be observed.
Material requirement: 1 marker per room; for areas larger than 50 m2, more
markers are required.
Material: Rubber round rod; base made in plastic, with adhesive strip
Item no. h [mm] Description unit
1000083 100Uponor marking setheight 100 mm 10 pcs
Uponor screed additive VD 450
For use as screed and mortar bed additive; improves screed quality thanks
to enhanced plasticization and better water retention.
Do not use in conjunction with levelling or anhydrite screed!
Use for 7 cm screed thickness: approx. 0.2 l/m2
Minimum screed covering: 30 mm at 2 kN/m2 or 45 mm at 5 kN/m2 in
conjunction with Uponor insulation/system board for 5 kN/m2
Curing time: 21 days
Item no. DT [d] Con. [l/m²] Description unit
1000084 21Uponor screed additive for betterheat conductivity, type VD 450 20 l
EEI-Int-RHC-01.1240
approx. 0.2
Uponor Radiant Heating/Cooling > Uponor underfloor heating accessories
Uponor under� oor heating accessories
Uponor screed additive VD 550
For use as screed and mortar bed additive; improves screed quality thanks
to enhanced plasticization and better water retention.
VD 550 N also ensures that the screed dries faster ((high early strength).
Do not use in conjunction with levelling or anhydrite screed!
Use for 7 cm screed thickness: approx. 0.2 l/m2
Minimum screed covering: 30 mm at 2 kN/m2 or 45 mm at 5 kN/m2 in
conjunction with Uponor insulation/system board for 5 kN/m2
Curing time: 8 days
Item no. DT [d] Con. [l/m²] Description unit
1000085 8Uponor screed additive for faster dryingVD 550 N 25 l
Uponor NF anti-freeze agent
Ethylene glycol-based anti-freeze agent, for use as additive in radiant
heating systems with Uponor pipes and standard heating system sealing
materials.
Vol. concentration to -20°C: 35%
Vol. concentration to -25°C: 40%
Vol. concentration to -30°C: 45%
Water volume in pipes (for calculation of mixing ratio):
14 x 2: 0.079 l/m
17 x 2: 0.13 l/m
20 x 2.3: 0.19 l/m
25 x 2.3: 0.33 l/m
Item no. Description unit
1005066Uponor antifreezer up to - 30°Ctype NF 20 l
EEI-Int-RHC-01.12 41
approx. 0.2
Uponor Radiant Heating/Cooling > Uponor underfloor heating manifolds
EEI-Int-RHC-01.1242
Uponor modular plastic manifold
1009214
1042420
1009215
1005233 14x2 100516816x2 100516917x2 100517020x2 1005171
1034524
1005100
1032702
1042471
1009217
1005605 (230 V)1000138 (24 V)
1006288
Number Item no. Item no. L
loops A B [mm]
3 1030580“ 1030583 150
4 1030581 1035084 200
6 1030582 1030585 300
A
With
balancing
screw
B
With
fl ow
meter
Manifold loops 2 3 4 5 6 7 8 9 10 11 12
1042420 Uponor plastic manifold single segment 2 1 1
1030580 Uponor plastic manifold 3 way 1 1 1
1030581 Uponor plastic manifold 4 way 1 1 1 2 1 1
1030582 Uponor plastic manifold 6 way 1 1 1 1 2
1009209 Uponor plastic manifold basic kit 1 1 1 1 1 1 1 1 1 1 1
1009209 (Uponor plastic manifold Basic Kit)
Uponor Radiant Heating/Cooling > Uponor underfloor heating manifolds
Uponor modular plastic manifolds
Uponor modular plastic manifold with balancing screw
Pack includes supply and return manifolds made of fibreglass reinforced
polyamid. Heating loop connections 3/4 MT euro-cone compatible with
Uponor compression adapters. Spacing of individual outlets 50 mm.
Manifolds can be joined to make the required number of ports. Uponor
actuators can be mounted on the return manifold. In each flow manifold
there are balancing valves for adjusting the supply in each loop.
Max. operating temperature: 60°C; Max. operating pressure: 6 bar.
Item no. outlets [-] l [mm] Description unit
1030580 3 150Uponor modular plastic manifoldwith balancing srew, 3 way 1 pcs
1030581 4 200Uponor modular plastic manifoldwith balancing srew, 4 way 1 pcs
1030582 6 300Uponor modular plastic manifoldwith balancing srew, 6 way 1 pcs
Uponor modular plastic manifold with flow meter
Pack includes supply and return manifolds made of fibreglass reinforced
polyamid. Heating loop connections 3/4 MT euro-cone compatible with
Uponor compression adapters. Spacing of individual outlets 50 mm.
Manifolds can be joined to make the required number of ports. Uponor
actuators can be mounted on the return manifold. Supply manifold with
adjustable and shut-off inserts (flow meter inspection window with scale of
0 – 4 l/min) for flow adjustment of individual heating loops.
Max. operating temperature: 60°C; Max. operating pressure: 6 bar.
Item no. outlets [-] l [mm] Description unit
1030583 3 150Uponor modular plastic manifoldwith flow meter, 3 way 1 pcs
1030584 4 200Uponor modular plastic manifoldwith flow meter, 4 way 1 pcs
1030585 6 300Uponor modular plastic manifoldwith flow meter, 6 way 1 pcs
Uponor accessories for plastic manifolds
Uponor plastic manifold single segment set
For Uponor plastic manifold with balancing screw for additional heating
loop extension. Supply segment with regulating valve, return segment
with thermostat upper section incl. cap for locking. Made of fibreglass
reinforced polyamid.
Max. operating temperature: 60°C; Max. operating pressure: 6 bar.
Item no. MT ["] Description unit
1042420 G 3/4Uponor plastic manifold single segmentset with balancing screw 1 set
Uponor plastic manifold single segment set with
topmeter
For Uponor modular plastic manifold with topmeter for additional heating
loop extension. Supply segment with adjustable and shut-off inserts
(topmeter inspection window with scale of 0 – 4 l/min) for flow adjustment
of individual heating loops. Return segment with thermostat upper section
incl. cap for locking. Made of fibre-glass reinforced polyamid. Max.
operating temperature: 60°C; Max. operating pressure: 6 bar.
Item no. MT ["] Description unit
1042471 G 3/4Uponor plastic manifold single segmentwith flow meter 1 set
EEI-Int-RHC-01.12 43
Uponor Radiant Heating/Cooling > Uponor underfloor heating manifolds
Uponor accessories for plastic manifolds
Uponor plastic manifold basic kit
For Uponor modular plastic manifold including brackets, flat sealing screw
connection pieces with swivel nut, thermometer and end pieces with air
vent, filling and draining tap and a by-pass.
Item no. l [mm] Description unit
1009209 150Uponor Plastic manifold Basic kitG1" 1 set
Uponor plastic manifold elbow connection set
For connection of supply/return pipes to Uponor modular plastic manifold
from the bottom. Made of fibreglass reinforced polyamid. Max. operating
temperature: 60°C; Max. operating pressure: 6 bar.
Item no. Description unit
1032702Uponor plastic manifold elbow connectionset for connection from below 1 set
Uponor hose connection for plastic manifold
For connection of refill/drainage hose 1/2" to Uponor plastic manifold.
Item no. Description unit
1009214Uponor hose connection for plasticmanifold to refill and drainage valve 1 set
Uponor plastic manifold retaining ring set
For connection of Uponor plastic manifold single segments to the manifold
in case of heating loop connection from top and bottom.
Item no. Description unit
1009215Uponor plastic manifold retaining ring set
1 set
Uponor flow meter for plastic manifold
For adjusting the water quantity of the individual heating loops in a range
of 0 -4 l/min. Water quantity is indicated in the inspection window. With
shut-off function. Made of fibre-glass reinforced polyamid.
Item no. Description unit
1009217Uponor flow meter 0-4l/minfor Uponor plastic manifolds 1 pcs
EEI-Int-RHC-01.1244
Uponor Radiant Heating/Cooling > Uponor underfloor heating manifolds
Uponor stainless steel manifolds
Uponor stainless steel manifold with flow meter
Manifold bar with flat-sealing screw connection and 1" FT with flat gasket,
one side with air vent, filling and drain tap, revolvable for pipe connection
and a 3/4" stop at the end. Heating loop connections 3/4" MT eurocone
according to DIN V 3838 compatible with all Uponor compression adapters
eurocone.
Spacing of individual outlets 50 mm.
Supply manifold with adjustable and shut-off inserts (flow meter inspection
window with scale of 0 – 4 l/min) for flow adjustment of individual heating
loops. Return manifold with valves incl. cap for locking. Uponor actuators
can be screwed directly on the return valves.
Fastener with sound-absorbing element included. Without ball valves and
Uponor compression adapters.
Made of stainless steel.
Max. operating temperature: 60°C
Max. operating pressure: 6 bar.
Item no. outlets [-] l [mm] Description unit
1013051 2 195Uponor stainless steel UFH-manifold 1"with flow meter, 2 way 1 pcs
1013052 3 245Uponor stainless steel UFH-manifold 1"with flow meter, 3 way 1 pcs
1013053 4 295Uponor stainless steel UFH-manifold 1"with flow meter, 4 way 1 pcs
1013054 5 345Uponor stainless steel UFH-manifold 1"with flow meter, 5 way 1 pcs
1013055 6 395Uponor stainless steel UFH-manifold 1"with flow meter, 6 way 1 pcs
1013056 7 445Uponor stainless steel UFH-manifold 1"with flow meter, 7 way 1 pcs
1013057 8 495Uponor stainless steel UFH-manifold 1"with flow meter, 8 way 1 pcs
1013058 9 545Uponor stainless steel UFH-manifold 1"with flow meter, 9 way 1 pcs
1013059 10 595Uponor stainless steel UFH-manifold 1"with flow meter, 10 way 1 pcs
1013060 11 645Uponor stainless steel UFH-manifold 1"with flow meter, 11 way 1 pcs
1013061 12 695Uponor stainless steel UFH-manifold 1"with flow meter, 12 way 1 pcs
Uponor stainless steel manifold with balancing screw
Manifold bar with flat-sealing screw connection and 1" FT with flat gasket,
one side with air vent, filling and drain tap, revolvable for pipe connection
and a 3/4" stop at the end. Heating loop connections 3/4" MT eurocone
according to DIN V 3838 compatible with all Uponor compression adapters
eurocone.
Spacing of individual outlets 50 mm.
Supply manifold with control valves, manual screws for preadjustment of
valves by an allen key.
Return manifold with valves incl. cap for locking. Uponor actuators can be
screwed directly on the return valves.
Fastener with sound-absorbing element included. Without ball valves and
Uponor compression adapters.
Made of stainless steel.
Max. operating temperature: 60°C
Max. operating pressure: 6 bar.
Item no. outlets [-] l [mm] Description unit
1013062 2 195Uponor stainless steel UFH-manifold 1"with balancing screw, 2 way 1 pcs
1013063 3 245Uponor stainless steel UFH-manifold 1"with balancing screw, 3 way 1 pcs
1013064 4 295Uponor stainless steel UFH-manifold 1"with balancing screw, 4 way 1 pcs
1013065 5 345Uponor stainless steel UFH-manifold 1"with balancing screw, 5 way 1 pcs
1013066 6 395Uponor stainless steel UFH-manifold 1"with balancing screw, 6 way 1 pcs
1013067 7 445Uponor stainless steel UFH-manifold 1"with balancing screw, 7 way 1 pcs
1013068 8 495Uponor stainless steel UFH-manifold 1"with balancing screw, 8 way 1 pcs
1013069 9 545Uponor stainless steel UFH-manifold 1"with balancing screw, 9 way 1 pcs
1013070 10 595Uponor stainless steel UFH-manifold 1"with balancing screw, 10 way 1 pcs
1013071 11 645Uponor stainless steel UFH-manifold 1"with balancing screw, 11 way 1 pcs
1013072 12 695Uponor stainless steel UFH-manifold 1"with balancing screw, 12 way 1 pcs
EEI-Int-RHC-01.12 45
Uponor Radiant Heating/Cooling > Uponor underfloor heating manifolds
Uponor manifold accessories
Uponor plastic manifold connection valve kit
For the hydraulic balancing and shut-off of the Uponor plastic manifold,
consisting of:
- G 1/Rp 1 inlet control valve for the hydraulic balancing and independent
shutt-off of the manifold, including hand wheel and display for settings/
closing
kvs value: 5.4 m3/h
- G 1/Rp 1 return valve for the shut-off of the manifold, including hand
wheel and display for closing; adaptable for Uponor plastic manifold
actuators.
kvs value: 6.4 m3/h
In conjunction with Uponor plastic manifold actuators, the
kvs value is 4.8 m3/h.
The connecting valve can be used to control individual zones.
Material: Housing made in brass, hand wheels made in polyamide
Max. testy pressure: 10 bar (water)
Item no. l [mm] h1 [mm] z [mm] MT ["] FT ["] A/F [mm] Description unit
1005100 80 50 45 G 1 Rp 1 38Uponor plastic manifold connection valveG-1/Rp 1 1 set
Uponor ball valve
Made of plated brass. With flat-sealing vertical screw connection 1 MT.
Length: 60 mm.
Item no. Description unit
1032701Uponor ball valve 1 MT x 1 FTflat sealing 1 set
Uponor coupling nipple
Made of tin-plated brass. Male thread acc.to DIN EN ISO 228-1.
Item no. MT ["] Description unit
1006641 3/4Uponor eurocone nipple MLC 3/4MT-3/4MT
10 pcs
l
d IG
SW
Uponor pipe connection PE-Xa 9.9
For connection of Uponor PE-Xa pipes 9.9 x 1.1 mm to Uponor manifolds
and Uponor connection box, made of brass.
Item no. d [mm] FT ["] l [mm] A/F [mm] Description unit
1005266 9.9 G 3/4 39 30Uponor PE-Xa pipe connection9.9 - 3/4 FT eurocone and one PE-X ring 10 pcs
EEI-Int-RHC-01.1246
Uponor Radiant Heating/Cooling > Uponor underfloor heating manifolds
Uponor manifold accessories
Uponor compression adapter
Compression adapter made of brass, for connection of Uponor PE-Xa pipes
to manifolds. Female thread 3/4"" eurocone acc. to DIN EN ISO 228-1.
Material: Brass
Item no. d [mm] s [mm] FT ["] A/F [mm] Description unit
1005168 14 2.0 G 3/4 30Uponor PE-Xa compression adapter witheurocone, 14x2.0 x 3/4 FT 10 pcs
1057368 16 1.8/2.0 G 3/4 30Uponor PE-Xa compression adapter witheurocone, 16x1.8/2.0 x 3/4 FT 10 pcs
1005170 17 2.0 G 3/4 30Uponor PE-Xa compression adapter witheurocone, 17x2.0 x 3/4 FT 10 pcs
1057370 20 1.9/2.0 G 3/4 30Uponor PE-Xa compression adapter witheurocone, 20x1.9/2.0x3/4 FT 10 pcs
SW
18
5
d
IG
Uponor plated compression adapter
Made of plated brass, for connection of Uponor PE-Xa pipes to manifolds.
Female thread 3/4" eurocone acc. to DIN EN ISO 228-1.
Item no. d [mm] FT ["] A/F [mm] p [bar] Description unit
1057441 16 G 3/4 30 6Uponor compression adapter S5.016x1.8/2.0x3/4 Eurocone plated 10 pcs
1057442 20 G 3/4 30 6Uponor compression adapter S5.020x1.9/2.0x3/4 Eurocone plated 10 pcs
Uponor compression adapter MLC 3/4" eurocone
Compression adapter made of brass, union nut and inner sleeve plated. For
connection of Uponor MLC pipes to manifolds (eg. Uponor manifold H).
Female thread 3/4" eurocone according to DIN EN ISO 228-1. Test safety
and no bevelling.
Item no. d [mm] FT ["] Description unit
1058089 14 3/4Uponor compression adapter MLC 14-3/4FTeurocone metal version 1 pcs
1058090 16 3/4Uponor compression adapter MLC 16-3/4FTeurocone metal version 1 pcs
1058091 18 3/4Uponor compression adapter MLC 18-3/4FTeurocone metal version 1 pcs
1058092 20 3/4Uponor compression adapter MLC 20-3/4FTeurocone metal version 1 pcs
Uponor manifold H cap
Made of coated brass, with eurocone sealing insert.
Item no. FT ["] Description unit
1014122 G 3/4Uponor manifold H cap 3/4FT eurocone
10 pcs
EEI-Int-RHC-01.12 47
Uponor Radiant Heating/Cooling > Uponor underfloor heating manifolds
Uponor pipe bend support
Uponor pipe bend support plastic
Made of impact resistant plastic to support 90° bends.
Item no. d [mm] Description unit
1047000 9.9Uponor pipe bend support plastic9.9 mm 50 pcs
Uponor pipe bend support
Made of galvanized steel as bend support for the pipes in the manifold
area.
Item no. d [mm] Description unit
1009004 16Uponor pipe bend support14-16 mm 50 pcs
1033975 17-18Uponor pipe bend support17-18 mm 50 pcs
1009233 20Uponor pipe bend support20 mm 50 pcs
Uponor manifold cabinets
Manifold cabinet concealed version
For attachment of Uponor manifolds, Uponor controller and Uponor
pump control stations on universal rail fixation incl. fixation set. Made of
galvanized steel. All visible parts are powder coated in white colour (RAL
9010).
Cabinet width (with frame): 555-950mm
Cabinet installation depth: 120-180mm
Cabinet installation high: 820-910mm
Item no. w [mm] h [mm] Description
1046991 555 820-910Uponor cabinet concealed version, UFH1width 555mm, colour white 1 pcs
1046992 710 820-910Uponor cabinet concealed version, UFH2width 710mm, colour white 1 pcs
1046993 785 820-910Uponor cabinet concealed version, UFH3width 785mm, colour white 1 pcs
1046994 950 820-910Uponor cabinet concealed version, UFH4width 950mm, colour white 1 pcs
EEI-Int-RHC-01.1248
Uponor Radiant Heating/Cooling > Uponor underfloor heating manifolds
Uponor manifold cabinets
Manifold cabinet on-wall version
For attachment of Uponor manifolds, Uponor controller and Uponor
pump control stations on universal rail fixation incl. fixation set. Made of
galvanized steel. All visible parts are powder coated in white colour (RAL
9010).
Cabinet width (with frame): 555-950mm
Cabinet installation depth: 160mm
Cabinet installation high: 820mm
Item no. w [mm] h [mm] Description
1046996 555 820Uponor cabinet on-wall version, UFH1width 555mm, colour white 1 pcs
1046997 710 820Uponor cabinet on-wall version, UFH2width 710mm, colour white 1 pcs
1046998 785 820Uponor cabinet on-wall version, UFH3width 785mm, colour white 1 pcs
1046999 950 820Uponor cabinet on-wall version, UFH4width 950mm, colour white 1 pcs
EEI-Int-RHC-01.12 49
Uponor Radiant Heating/Cooling > Uponor controls
EEI-Int-RHC-01.1250
Uponor individual radio room temperature control with Dynamic Energy Management (DEM)
The Uponor individual radio room
temperature control system with
DEM has been developed on the
basis of the existing individual radio
room temperature control. Apart
from the colour of the controller
(previously white, now grey), there
are many more diff erences between
the two versions. The advanced sys-
tem comes with a range of features
that make installation even easier.
Apart from the great energy effi -
ciency during operation, fast instal-
lation and user-friendly operation
that are standard features of all
Uponor systems, the new individual
room temperature control makes
heating and cooling even more
comfortable.
The automatic balancing function
does away with time-consuming
manual hydraulic balancing. In most
cases, there is no need for recalcu-
lation of the valve settings, which is
normally required aft er a change of
the room layout or the fl oor cover-
ing. The heat distribution in the
room is evaluated by a bespoke
soft ware solution. The relevant val-
ues are stored and the system is
automatically balanced at regular
intervals. This guarantees optimum
energy distribution!
The comfort setting prevents that
heating surfaces become too cool
when the room is heated with an
alternative source (e.g. open fi re-
place). The supply diagnosis moni-
tors the heat performance in all
rooms and signals any insuffi cient
or excess supply to the I-76 inter-
face. The room bypass function is
particularly suitable for systems
with specifi c minimum fl ow require-
ments. Incorrectly assigned thermo-
stats are automatically detected and
rectifi ed by the room check func-
tion.
Your benefi t
Energy savings up to 12 %
thanks to greater effi ciency
No need for manual hydrau-
lic balancing
High time saving during
installation
More accurate and faster
control, up to 25% faster
response time
Higher comfort through
improved heat distribution
Easy to operate
Reliable operation with
minimum support
No need for recalculation af-
ter change to heating circuit
layout/size
System not aff ected by
subsequent change of fl oor
covering
Easy troubleshooting
"Clean solution" for renova-
tion
Remote control via SMS con-
nection possible
Easy, well-tried handling
Optional automatic switch
over to heating-/ or cooling
mode with the Uponor heat-
ing/cooling controller C-46
Operation of up to three
controller C-56 from one
interface I-76
Uponor radio controller
(consisting of controller and interface)
Item no. 1045562
Uponor radio thermostat
T-75
Item no. 1000502 (white)
Item no. 1000504 (silver)
Item no. 1046114 (grey)
Uponor radio controller C-56
(for system extension)
Item no. 1045565
Uponor thermostat T-54
Item no. 1045572
Uponor SMS-module
R-56
Item no. 1045570
Uponor interface I-76
Item no. 1045568
20,5
20,5
Uponor Radiant Heating/Cooling > Uponor controls
Uponor Radio control
Uponor controller with interface C-56+I-76 radio
For receiving and transforming of radio signals from the thermostats,
with integrated DEM functions
consisting of:
Controller C-56 with
- Electronic control
- Reception of max. 12 room-thermostats
- Connection of max. 14 actuators 24 Volt
- Heating/Cooling function switched by external contact
- Pump relay
- Valve exercise, pump exercise
Interface I-76 with
- Display, back lighted, new look, blue full dot matrix
- Menu in English,
Integrated functions:
- Five temperature setback progams,
- Max/min temperature limitations,
- Holiday temperature
- Automatic summer/wintertime change
- Auto adapt function
- Room check function
- Room bypass function
- The Interface can control up to 3 controllers
Accessories
External Antenna, cables for connections, mounting material
Mark of conformity: CE
Operational voltage: 230 V / 50 Hz
Max. power input per actuator: 0,2 A
Protection class: IP 30 (EN 60 529)
Colour: grey (RAL 7015)
Item no. OV [V] P [W] EP/a [W] colour [-] Description unit
1045562 230 1 >2 greyUponor controller with interfaceC-56+I-76 radio, grey 1 set
316 60
110
50 20
24 V
Uponor controller C-56 radio
For receiving and transforming of radio signals from the thermostats,
to use the DEM function with the I-76.
consisting of:
Controller C-56 with
- Electronic control
- Reception of max. 12 room-thermostats
- Connection of max. 14 actuators 24 Volt
- Heating/Cooling function switched by external contact
- Pump relay
- Valve exercise, pump exercise
- Plastic color grey (RAL 7015)
- Protection rating IP 30
Accessories
External Antenna, cables for connections, mounting material
Item no. OV [V] P [W] EP/a [W] colour [-] Description unit
1045565 230 1 >2 greyUponor controller C-56 radiogrey 1 pcs
EEI-Int-RHC-01.12 51
Uponor Radiant Heating/Cooling > Uponor controls
Uponor Radio control
Uponor interface I-76
For combination with the controller C-56 to use the DEM function
Interface I-76 with
- Display, back lighted, new look, blue full dot matrix
- Menu in English,
Integrated functions:
- Five temperature setback progams,
- Max/min temperature limitations,
- Holiday modus
- Automatic summer/wintertime change
- Auto adapt function
- Room check function
- Room bypass function
- For controling of up to 3 controllers
Protection class: IP 30 (EN 60 529)
Colour: grey (RAL 7015)
Item no. l [mm] w [mm] h [mm] Description unit
1045568 110 110 30Uponor interface I-76grey 1 pcs
Uponor thermostat display T-75 radio
Designed as a wireless single room temperature sensor, measuring the
perceived room temperature and transmitting the values to the wireless
base unit or wireless control module, with display showing the set and
measured room temperature, consisting of:
Housing with
- Temperature programming buttons
- Control electronics
Signal range: max. 30 m
Signal frequency: 868 MHz
Power supply: Alkaline battery, service life approx. 5 years, size AAA
Transmission power: approx. 1 mW
Set temperature range: 5 - 30 °C
Colour: pure white (near RAL 9010) or silver (near RAL 9006)
Item no. l [mm] w [mm] h [mm] colour [-] Description unit
1000502 124 66 16 whiteUponor thermostat display T-75 radiowhite 1 pcs
1000504 124 66 16 silverUponor thermostat display T-75 radiosilver 1 pcs
1046114 124 66 16 greyUponor thermostat display T-75 radiogrey 1 pcs
Uponor thermostat mounting kit
Accessory for wireless room sensor; use this kit to position and/or secure
the room sensor anywhere in the room on the wall; with removal/child
safety device, consisting of:
- Mounting plate with clip
- Bracket
- Adhesive pads for fixture to smooth surfaces (tiles, etc.)
Colour: pure white (near RAL 9010) or silver (near RAL 9006) or grey
Item no. colour [-] Description unit
1000503 whiteUponor thermostat mounting kitfor T-75 radio, white 1 pcs
1000505 silverUponor thermostat mounting kitfor T-75 radio, silver 1 pcs
1046115 greyUponor thermostat mounting kitfor T-75 radio, grey 1 pcs
EEI-Int-RHC-01.1252
Uponor Radiant Heating/Cooling > Uponor controls
Uponor Radio control
Uponor thermostat T-55 radio
Radio thermostat, including batteries and screws for mounting. Operating
distance: max. 30 m. Set point range 6 – 30°C.
Item no. l [mm] w [mm] h [mm] Description unit
1000527 72 72 21Uponor thermostatT-55 Radio 1 pcs
Uponor thermostat public T-54
Radio thermostat with inside setting, including batteries and screws for
mounting. Operating distance: max. 30 m. Set point range 6 – 30°C.
SMS module R-56 can be connected.
Floor sensor for min/max limitation of floor temperature can be connected.
Item no. l [mm] w [mm] h [mm] Description unit
1045572 72 72 21Thermostat PublicT-54 Radio 1 pcs
Uponor SMS module R-56
For connection with the thermostat T-54, to activate and control the
system settings and monitor the actual room temperature in a reference
room via SMS.
Item no. l [mm] w [mm] h [mm] Description unit
1045570 185 75 28Uponor SMS moduleR-56 1 pcs
Uponor floor sensor
Floor sensor for connection to the thermostats (radio and wired) with
external input with sensor attached to 4m cable.
Item no. d [mm] l [mm] l1 [mm] Description unit
1000538 5 4000 25Uponor floor sensorfor T-33, T-37 1 pcs
EEI-Int-RHC-01.12 53
Uponor Radiant Heating/Cooling > Uponor controls
Uponor outdoor sensor
Uponor outdoor sensor
Outdoor sensor
for connection to the Thermostats with external input
with Sensor box and seperate 5 m cable
Has to be connected to thermostat T-54 in a system with
Interface I-76 to display outdoor temperature.
- IP65
- Plastic color 7035
Item no. colour [-] Description unit
1000529Uponor outdoor sensorfor T-33, T-37, T-53 1 pcs
Uponor installation cable
Twisted pairs cable to connect:
- Interface to Controller
- Controller to Controller
- Extension for Antenna cable
Item no. l [m] Description unit
1000515 15Uponor installation cable15m 1 pcs
Uponor repeater
To solve problems with radio transmission, for on-wall mounting.
Item no. OV [V] P [W] l [mm] w [mm] h [mm] Description unit
1000518 230 < 1 160 75 26Uponor repeater230 V 1 pcs
Uponor KNX media coupler R-76
can connected the C-56 Radio to a standard KNX bus. This device will act
as a interface between the C-56 Radio and the KNX wired bus.
Conformity: CE
Protection Class: IP 30
Item no. l [mm] w [mm] h [mm] Description unit
1045571 203 75 26.5KNX Media CouplerR-76 1 pcs
EEI-Int-RHC-01.1254
light grey
Uponor Radiant Heating/Cooling > Uponor controls
EEI-Int-RHC-01.12 55
Uponor 24 V individual room climate control system
Wired individual room tempera-
ture control system with wide
range of components.
The Uponor 24 V individual room
climate control system consists of
electronic components that have
been specially devised for combina-
tion with each other (3 thermostat
models, 2 controllers and optional
timer). As soon as a thermostat
detects that heating or cooling in a
room must be adjusted, the con-
troller operates the 24 V thermo
drives accordingly. The three ther-
mostat models available for this
system can be freely combined with
each other and are connected to
the controllers through non-polari-
ty 2-core cables (6-12 V) that can-
not be confused.
Choose between two controller
types
Depending on the size of the heat-
ing system and the specifi c require-
ments, you can install a 6-channel
(C-33) or 12-channel (C-35) con-
troller.
The 12-channel controller caters for
maximum 12 thermostats and 14
thermal actuators plus an optional
timer I-36. The 12-channel C-35
controller also provides the option to
switch over between heating and
cooling.
The device is wired in such a way that
several thermal actuators can be com-
bined with a single thermostat with-
out the need for wired bridges. Ther-
mostats and thermal actuators are
connected to the controller through
easy-to-use plug-in wiring terminals.
Your benefi t
Low-cost and safe thermo-
stat wiring (6-12 V)
Choice of three thermostat
models
Connection of optional fl oor
sensors
Room temperature lowering
with Uponor timer and two
timer zones
Optional limitation of set
point temperature settings
Also suitable for surface
cooling systems with dew
point monitoring
Optional automatic switch-
ing over between heating/
cooling with Uponor heat-
ing/cooling controller C-46
Important:
The Uponor 24 V individual
room climate control system
is a stand-alone system of
tailor-made components that
cannot be replaced with
third-party devices.
Uponor Radiant Heating/Cooling > Uponor controls
Uponor wired control
Uponor controller C-33, 6 channels
Controller C-33 with electronic control, connection of max. 6 Thermostats,
connection of max. 8 actuators 24 Volt, pump relay, pump / valve exercise,
power LED, plastic color RAL 9010, protection rating IP 30, accessories,
mounting material.
Item no. OV [V] l [mm] w [mm] h [mm] Description unit
1000531 24 315 110 58Uponor controller, 6 channelsC-33 wired 1 pcs
Uponor controller C-35, 12 channels
For the power supply of max. 12 room sensors (models T-33,T-35, T-37)
and max. 14 thermo drives (models TA/TR),24 V. Preassembled unit,
consisting of:
- Housing including mounting accessories
- Control electronics with microprocessor
- Pump logics
- Valve interval
- Overload protection
- Connecting cable with Euro standard plug
- Floating heating/cooling switching by external signal
- Connection port for Uponor I-35 timer with 2 temperature lowering
programs and for Uponor dew point converter
Conformity: CE
Colour: pure white (near RAL 9010)
Protection class: IP 30 (EN 60529)
Max. power consumption per TA 24: 0.2 A (switching peak)
Effective power per TA 24: <2 W
Item no. OV [V] l [mm] w [mm] h [mm] Description unit
1000533 24 315 110 58Uponor controller, 12 channelsC-35 wired 1 pcs
Uponor Thermostat T-34
Wired flush mounted thermostat for room temperature control
Consisting of:
- Flush thermostat T34 with
- Dial for settings
- Sensor for air temperature
- LED for indication
- Two wires
- Plastic color RAL 9010
General functions
- Setpoint range 6-30°C
- Setting range can be limited mechanically by moving pins under the dial
Item no. l [mm] w [mm] h [mm] Description unit
1048010 81 81 14.7Uponor thermostat flush T-34 wired
1 pcs
EEI-Int-RHC-01.1256
Uponor Radiant Heating/Cooling > Uponor controls
Uponor wired control
Uponor thermostat T-35
For connection to Uponor controller C-33 or C-35 with:
- Dial for settings
- Sensor for air temperature
- LED for indication
- Two wires
- Plastic color RAL 9010
Functions
- Setpoint range 6-30°C, mark at 21°C
- Setting range can be limited mechanically by moving pins under the dial
Item no. l [mm] w [mm] h [mm] Description unit
1000535 72 72 21Uponor thermostatT-35 wired 1 pcs
Uponor thermostat T-37 for external sensor
For connection to Uponor controller C-33 or C-35 with:
- Dial for settings
- Sensor for air temperature
- LED for indication
- Terminal for Floor Sensor
- Two wires
- Plastic color RAL 9010
Functions
- Setpoint range 6-30°C, mark at 21°C
- Setting range can be limited mechanically by moving pins under the dial
- Internal setting for the Floor Senor, range print on circuit board
Item no. l [mm] w [mm] h [mm] Description unit
1000536 72 72 21Uponor thermostat f. external sensorT-37 wired 1 pcs
Uponor wall frame
Wall frame to cover standard wall boxes or in case of renovation shades of
old thermostats, size 90*90, plastic color RAL 9010
Item no. l [mm] w [mm] h [mm] Description unit
1000539 90 90 8Uponor wall framefor T-33, T-35, T-37 1 pcs
EEI-Int-RHC-01.12 57
Uponor Radiant Heating/Cooling > Uponor controls
Uponor wired control
Uponor digital thermostat T-36
Consisting of:
- Digital thermostat T36
Options:
- Floor sensor (1000538) (sold seperately)
General functions
- Room temperature regulation with internal sensor
- Room or remote temperature display
- Room temperature, Room and max/min floor temp (heating/cooling) ,
remote sensor regulation selectable. - Automatic or Manual balancing
- Comfort / ECO mode.
- Lock indication
- Standby/OFF mode
- Modes displayed on LCD: Heating, Cooling, ECO, Lock, Standby,
Comfort/ECO, Auto/Man balancing.
- Displayed temperature calibration
- Window open function
- 3 button keyboard +/-/OK
- Hidden reset
Item no. l [mm] w [mm] h [mm] Description unit
1048011 85 83 25Uponor digital thermostat T-36 wired
1 pcs
Uponor programmable digital thermostat T-38
Consisting of:
- Programmable digital thermostat T38
Options:
- Floor sensor (1000538) (sold seperately)
General functions
- Room or remote temperature display.
- Room temperature, Room and max/min floor temp (heating/cooling) ,
remote sensor regulation selectable.
- Automatic or Manual balancing
- Comfort / ECO mode.
- Lock indication.
- Standby/OFF mode
- 4 Pre pre-recorded modifiable programs for working days / week-end /
week
- Date and time, with summer/winter change, power failure proof
- Hidden reset
- Temporary or permanent override mode
- Modes displayed on LCD: Heating, Cooling, Lock, Standby, Holiday,
Comfort/ECO
- Displayed temperature calibration
- Window open function
- Powered by base unit (no batteries)
Item no. l [mm] w [mm] h [mm] Description unit
1048012 85 83 25Uponor programmable digital thermostat T-38 wired
1 pcs
EEI-Int-RHC-01.1258
Uponor Radiant Heating/Cooling > Uponor controls
Uponor wired control
Uponor thermostat Public T-33
For connection to Uponor controller C-33 or C-35 with:
- Plain cover
- Internal setting
- Sensor for air temperature
- Terminal for Floor Sensor
- Two wires
- Plastic color RAL 9010
Functions
- Setpoint range 6-30°C, mark at 21°C
- Internal setting for the Floor Senor
- Room sensor
- Max/min limitation with floor sensor
Item no. l [mm] w [mm] h [mm] Description unit
1000537 72 72 21Uponor thermostat publicT-33 wired 1 pcs
Uponor timer I-36
Consisting of:
- Programmable digital timer I36
General functions
- 2 zones programming comfort / ECO
- Display of zone status and time
- Pre-recorded modifiable programs for working days / week-end / week
- Date and time, with summer/winter change, power failure proof
- Lock mode, standby OFF mode
- Hidden reset
- Temporary or permanent override mode
- Dry contact input for forced ECO mode.
- Example: Signal from Uponor R-56 SMS module for remote control
- Powered by base unit (no batteries)
Item no. l [mm] w [mm] h [mm] Description unit
1048013 85 83 25Uponor timer I-36 for C-35
1 pcs
Uponor control accessories 24 V
Uponor actuator 24V
24 V, with open/closed indicator, suitable for use with Uponor plastic
manifolds in connection with Uponor radio or wired control system. Closes
when idle. With all-round shower protection (IP 54). Suitable for operation
at ambient temperature of up to 60°C.
Threaded connector M 30 x 1.5 mm MT.
Height: 54 mm.
Item no. MT [-] d [mm] h [mm] OV [V] P [W] Description unit
1000138 30x1.5 40 54 24 < 2Uponor actuator 24V for plasticmanifold, 30 x 1,5 MT 1 pcs
Uponor actuator 24V
24 V, with open/closed indicator, suitable for use with Uponor stainless
steel manifolds in connection with Uponor control system. Closes when
idle. With all-round shower protection (IP 54). Suitable for operation at
ambient temperature of up to 60°C.
Threaded connector M 30 x 1.5 mm FT.
Height: 56 mm
Item no. FT m [-] d [mm] h [mm] OV [V] P [W] Description unit
1013008 30x1.5 40 56 24 ~ 2Uponor actuator 24V for stainlesssteel manifold, 30 x 1,5 FT 1 pcs
EEI-Int-RHC-01.12 59
Uponor Radiant Heating/Cooling > Uponor controls
Uponor control accessories 24 V
Uponor return temperature limiter
For use in low-temperature range for combined underfloor/ radiator
heating systems respectively wall-radiator heating systems for the
regulation of the return temperature of small heating areas up to max. 15
m2. Consists of installation casing with cover, fast-action air vent valve,
thermostat for return temperature limiting set between 25 and 65 °C.
Factory-made limitation of return temperature approx. 50°C. Suitable for
Uponor compression adapter with 3/4" eurocone.
Dimensions: (H x W x D) 150 x 122 x 65 mm
D after installation: 5 mm
Item no. Description unit
1013005Uponor return temperature limiter
1 pcs
Uponor wired control 230 V
Uponor Controller C-23
Uponor Controller C-23 for wiring up to 6 room thermostats and max. 14
actuators. Up to 4 actuators per channel are possible.
Optional: pump relay. IP43.
Item no. l [mm] w [mm] h [mm] OV [V] Description unit
1058426 310 90 65 230Uponor Controller C-23230V, WIRED 1 pcs
Uponor Pump Relay for Controller C-23
Pump relay for C-23 6 room Controller
Item no. l [mm] w [mm] Description unit
1058427 310 90Uponor Pump Relay for Controller C-23230V, WIRED 1 pcs
Uponor Thermostat T-23
Standard Thermostat 230 V, with on/off contact
Item no. Description unit
1058422Uponor Thermostat T-23230V, WIRED 1 pcs
Uponor Thermostat Flush T-24
Flush Mounted Thermostat 230 V. On/off contact, insulated cover,
protective cap, frame (neutral), 50 x 50 mm cover, pure white , glossy
Item no. Description unit
1058423Uponor Thermostat Flush T-24230V, WIRED 1 pcs
EEI-Int-RHC-01.1260
Uponor Radiant Heating/Cooling > Uponor controls
Uponor wired control 230 V
Uponor Thermostat H/C T-25
Heating/Cooling Thermostat 230 V with a change over contact for
maximum 5 actuators and a heating / cooling switch. For 2 pipe
installation, specially for heatpump.
Item no. Description unit
1058424Uponor Thermostat H/C T-25230V, WIRED 1 pcs
Uponor Thermostat Prog. Digital T-26
Digital Programmable Thermostat 230V. Energy saving feature calculates
heat up time of system. Includes holiday mode, temporary over-ride and
specified duration, 5/2 or 7 day programme, floor temperature control,
lock facility, status display on current thermostat mode.
Item no. Description unit
1058425Uponor Thermostat Prog. Digital T-26230V, WIRED 1 pcs
Uponor control accessories 230 V
Uponor actuator 230 V
230 V, with open/closed indicator, suitable for use with Uponor plastic
manifolds. Closes when idle. With all-round shower protection (IP 54).
Suitable for operation at ambient temperature of up to 60°C.
Threaded connector M 30 x 1.5 mm MT.
Height: 54 mm.
Item no. MT [-] d [mm] h [mm] OV [V] P [W] Description unit
1005605 30x1.5 40 54 230 < 3Uponor actuator 230V for plasticmanifold, 30 x 1.5 MT 1 pcs
Uponor actuator 230 V
230 V, with open/closed indicator, suitable for use with Uponor stainless
steel manifolds. Closes when idle. With all-round shower protection (IP 54).
Suitable for operation at ambient temperature of up to 60°C.
Threaded connector M 30 x 1.5 mm FT.
Height: 56 mm
Item no. FT m [-] d [mm] h [mm] OV [V] P [W] Description unit
1013006 30x1.5 40 56 230 ~ 3Uponor actuator 230V for stainlesssteel manifold, 30 x 1,5 FT 1 pcs
EEI-Int-RHC-01.12 61
Uponor Radiant Heating/Cooling > Uponor controls
EEI-Int-RHC-01.1262
Uponor Controls
Heating-supply temperature control with radio individual room
temperature control
Functional description
The wireless room temperature sensor measures the
operative room temperature. Through the wireless con-
troller, the thermal actuators and manifold valves, it
controls the heat release from the respective room heat-
ing surface. The wireless basic control unit allows for
The diagram shows a simplifi ed illustration of the key control components. For detailed instruc-
tions regarding the installation and operation of the system, refer to the manuals shipped with the
components or download the relevant documents from www.uponor.com.
Components
1 Radio controller C-56 with interface I-76
2 Radio controller C-56
3 Antenna
4 Wireless thermostat
5 Climate controller C-46
6 Supply/return sensor
7 Outdoor sensor
8 Manifold
9 heating source
4
6 6 5
1
4
2 x 0,5 mm2
max. 20 m(je Verbindung)
4
2
2 x 0,4 mm2
max. 50 m
7
23 3
9
3
M
99
8
individual room temperature control. It is thus for exam-
ple possible to assign diff erent temperature lowering
times to diff erent rooms. Together with the remote con-
trol system, the C-46 heating controller adjusts the sup-
ply temperature depending on the actual weather con-
ditions and the programmed heating times.
Uponor Radiant Heating/Cooling > Uponor controls
EEI-Int-RHC-01.12 63
heating/cooling - supply temperature control with automatic H/C
switchover valve powerd by boiler and chiller
Functional description
Depending on the outdoor and room temperature, the
C-46 heating/cooling controller switches the switch-
over valve installed by the operator from the heating to
the cooling source. The H/C switching module switches
the C55/C56 wireless controller from heating to cooling
mode, as the manifold valves must be opened as the
room temperature increases (reverse operation of ther-
mal actuators). For cooling, the relative air humidity in
the room must also be measured, in addition to the
room temperature. This is done through the humidity
sensor H-56. It is important to prevent that the temper-
The diagram shows a simplifi ed illustration of the key control components. For detailed instruc-
tions regarding the installation and operation of the system, refer to the manuals shipped with the
components or download the relevant documents from www.uponor.com.
Components
1 Radio controller C-56 with interface I-76
2 Radio controller C-56
3 Antenna
4 Wireless thermostat
5 H/C relay
6 Climate controller C-46
7 Supply/return sensor
8 Outdoor sensor
9 Chiller
10 Switch-over valve
ature drops below the dew point, as this would lead to
condensation on cold system components. The C-46
heating/cooling controller regulates the cooling water
supply temperature through the control valve to keep it
above the dew point temperature. This ensures that the
system components from the control valve downwards
are protected against damage from condensation that
tends to occur when the actual temperature drops
below the dew point. Depending on the cooling water
temperature, the system components from the chiller to
the control valve must be insulated with diff usion-tight
material.
4
7
9
7 6
1
4
2 x 0,5 mm2
max. 20 m
2 x 0,5 mm2
max. 20 m(je Verbindung)
4
2
2 x 0,4 mm2
max. 50 m
8
23 3
10
3
M
100 m (vom Elektrofach-betrieb zu prüfen)
Uponor Radiant Heating/Cooling > Uponor controls
Uponor climate controller
Uponor climate controller C-46
Weather compensator controlling supply water in heating.
Can be integrated in the C-56 system via bus connection.
Consisting of:
- Climate Controller C-46
- Wired Outdoor sensor
- Wired Supply sensor
Options:
- Antenna Module for connection to wireless Thermostats
- Wired Indoor sensor
- Wired Return sensor.
General functions
- Installation wizard gives easy and fast installation & set-up
- Quick menu system gives easy access to basic settings
- Integration with C-56 system via bus gives CC access to zone data from
C-56.
- System information, H/C-state, ECO-mode etc are also shared on the
bus.
- Automatic summer/wintertime change
- ECO/Comfort timer in CC if no I-76 in the system.
- Clock backup 8 hours
- Alarm at disturbance
- Pumpmanagement with internal fuse
- Supports 24V Thermal Actuator
or 0-10V controlled rotating mixer motor,
or variable speed pump
- General purpose input for Heating+Cooling switch
or Snow detection
- General purpose output for Heating+Cooling command
or Dehumidification command
or Error signalling
- Input indoor sensor
- Input outdoor sensor
- Input Supply Sensor
- Input Return Sensor
Accessories
Outdoor sensor (5m cable), Supply sensor (4m cable), mounting material
Item no. l [mm] w [mm] h [mm] Description unit
1047844 174 106 80Uponor climate controller C-46
1 pcs
EEI-Int-RHC-01.1264
Uponor Radiant Heating/Cooling > Uponor controls
Uponor climate controller
Uponor climate controller C-46 extended
Weather compensator controlling supply water in heating + cooling
Can be integrated in the C-56 system via bus connection.
Consisting of:
- Climate Controller C-46
- Antenna
- Wireless Humidity Sensor H-56
- Wired Outdoor sensor
- Wired Supply sensor
Options:
- Wired Indoor sensor
- Wired Return sensor
- Additional 5 RH-sensors
General functions
- Installation wizard gives easy and fast installation & set-up
- Quick menu system gives easy access to basic settings
- Integration with C-56 system via bus gives CC access to zone data from
C-56.
- System information, H/C-state, ECO-mode etc are also shared on the
bus.
- Automatic summer/wintertime change
- ECO/Comfort timer in CC if no I-76 in the system.
- Clock backup 8 hours
- Alarm at disturbance
- Pumpmanagement with internal fuse
- Supports 24V Thermal Actuator
or 0-10V controlled rotating mixer motor,
or variable speed pump
- General purpose input for Heating+Cooling switch
or Snow detection
- General purpose output for Heating+Cooling command
or Dehumidification command
or Error signalling
- Input indoor sensor
- Input outdoor sensor
- Input supply sensor
- Input return sensor
Humidity Sensor H-56:
- Wireless RH sensor with battery alarm
- incl Batteries and mounting kit
- Connects to C-46 with antenna or via C-56
Accessories
Outdoor sensor (5m cable), Supply sensor (4m cable), mounting material ,
3m Antenna cable
Item no. l [mm] w [mm] h [mm] Description unit
1047845 174 106 80Uponor climate controller C-46 extended
1 pcs
Uponor humidity sensor H-56
- Wireless RH sensor with battery alarm
- incl Batteries and mounting kit
- Connects to C-46 with antenna or via C-56
Item no. l [mm] w [mm] h [mm] Description unit
1047846 72 72 21Uponor humidity sensor H-56
1 pcs
EEI-Int-RHC-01.12 65
Uponor Radiant Heating/Cooling > Uponor controls
Uponor climate controller
Uponor supply or return sensor for C-46
- For connection directly to C-46
- Sensor with 4m wire.
Note: Return sensor only needed for average temperature control
Item no. Description unit
1047847Uponor supply or return sensor for C-46
1 pcs
Uponor outdoor or indoor sensor for C-46
- For connection directly to C-46
- Additional connection wire needed.
Item no. Description unit
1047848Uponor outdoor or indoor sensor
1 pcs
Uponor relay H/C, 24 V
For automatic heating/cooling switchover on external signal.
Item no. OV [V] l [mm] w [mm] h [mm] Description unit
1000516 24 160 50 95Uponor relay H/C24 V 1 pcs
1000517 230 160 50 95Uponor relay H/C230 V 1 pcs
Uponor Mixer Motor
For mounting on a mixing valve and used in combination with the C-46.
Externally powerd.
Item no. Description unit
1002356Uponor Mixer motor 24Vwith 0-10V signal 1 pcs
1002357Uponor Mixer motor 230V / 3PT
1 pcs
Uponor Wall Power Supply
230V/24V Power supply with Euro-plug for 0-10V controlled mixer motor.
Item no. Description unit
1048763Uponor Power supply 230V/24Vfor C-46 mixer motor 1 pcs
EEI-Int-RHC-01.1266
Uponor Radiant Heating/Cooling > Uponor controls
EEI-Int-RHC-01.12 67
Uponor control stations for heating/cooling
UFH systems
RS2
Uponor room control
station
RS 2 up to 2 kW
Unit set 6
Uponor constant tempera-
ture control unit set 6
up to 6 kW
Push 23
Uponor pump group
up to 10 kW
MPG 10
Uponor pump group
3 to 10 kW
with controller
Unit set type 1
Uponor pump group
up to 12 kW
CPG 15
Uponor central pump group
3 to 15 kW
with controller
Control stations
Minitec
Siccus
Tecto
Self attach-
ing system
Tacker &
Clamp track
Pipe positi-
oning panel
Classic
Uponor Radiant Heating/Cooling > Uponor controls
Uponor control stations
Uponor room control station RS 2
Pumpgroup for control of UFH in single rooms, with
brass-housing, bracket for front-or backside installation, integrated pump
grundfos UP15-14B, venting screw, secondary max.- limiter 25-55°C,
balancing valve, actuator 230V,
1-3 kW
max. 90° primary, max. 55° secondary, max. 10 bar
valve kvs 1,25 m³/h
Pump 15-40 for 0,1-0,45 ³/h 1,2-03, m, 230V, 30W,
connection:
secondary loop 3/4"" eurocone
primary valves with clampconnection for CU-Pipe 15mm
Pump needs 230V pump power supply with external switch.
connectible to electrical thermostats no. 1000132
calculation example for Rl,B 0,05m²K/W (tiles)
pipe 9,9x1,1 100mm 2 loops a' 60m, =2x 6m² 0,96kW
pipe 14x2 150mm 2loops a' 60m = 2x 9m² 1,8 kW
pipe 17x2 150mm 2loops a' 90m = 2x14m² 2,8 kW
pipe 20x2,0 150mm 2loops a' 105m = 2x16m² 3,2 kW
Item no. Q [kW] l [mm] w [mm] h [mm] c/c [mm] c/c1 [mm] Description unit
1005576 2 360 145 80 60 40Uponor Room control unit RS 2up to 2 kW with actuator 230V FT 1 pcs
G 3/4
G 3/4 G 3/4
ra
l
Uponor branch connection
For extension of RS 2 room control station to 2 heating circuits; direct
connection of heating circuit G 3/4 fitting with Euro cone
Each kit includes 2 fittings.
Material: Brass
Item no. l [mm] c/c [mm] Description unit
1005675 50 40Uponor branch connection for connectionof two loops to Uponor RS 2 1 set
Uponor Push 23
Pumpgroup with thermostat and pump energy efficiency class A,
Thermostat with capillary sensor 20-55°C for supply temp.,
Pump Grundfos Alpha2L 15-60 0,1-2,4 m³/h, H: 4-0,9 m
supply thermostat valve kvs 0,9 m³/h
return balancing valve kvs 2,0 m³/h
secondary connections G1A for connection to uponor UFHC manifolds,
10 kW
max. 90° primary, max. 55° secondary, max. 10 bar
Item no. Description unit
1046870Uponor push 23 A, pump and mixing groupfor constant temperature control 1 pcs
EEI-Int-RHC-01.1268
Uponor Radiant Heating/Cooling > Uponor controls
Uponor control stations
Uponor Manifold Pump Group MPG 10
Pumpgroup for connection to Uponor UFHC-manifolds,
installation with manifolds on-wall or in cabinets,
pre-mounted with supply temperature control C-46 with integrated
interface to uponor single room control C-56
3-way-mixing valve, motor drive
kvs 4,0
pump energy efficiency class A (Grundfos alpha2L 25-60)
0,1 - 2,5 m³/h H: 6,0-1 m
proportional pressure control
primary ballvalves, connection Rp1 (FT)
secondary connection G1A (MT)
supplytemperature sensor
outdoor temperature sensor (install. on buildingsite)
3-10 kW
max. 90° primary, max. 60° secondary, max. 10 bar
Item no. Description unit
1048780Uponor Manifold Pump Group MPG 10with controller 1 pcs
Uponor Manifold Pump Group MPG 10 without
controller
to connect to uponor UFHC-manifolds,
installation with manifolds on-wall or in cabinets,
without actuator, without control ,
for connection to external boiler control or connection to Uponor climate
controller C-46 heating/cooling,
requires Motor 1002356 or 1002357
3-way-valve mixing
kvs 4,3
pump energy efficiency class A (Grundfos alpha2L 15-60)
Q: 0,1-2,5 m³/h, H: 6-2,4 m
proportional pressure control
connection G1A secondary
ball valve+balancing valve primary
for installation left or right of manifold
3-10 kW
max. 90° primary, max. 60° secondary
Item no. Description unit
1048781Uponor Manifold Pumpgroup MPG 10without controller 1 pcs
EEI-Int-RHC-01.12 69
Uponor Radiant Heating/Cooling > Uponor controls
Uponor control stations
Uponor Central Pump group CPG 15
Pumpgroup for installation in boiler rooms or on-wall with Uponor UFHC-
manifolds, pre-mounted with supply temperature control C-46 with
integrated interface to Uponor single room control C-56
3-way-mixing valve, motor drive
kvs 6,3
pump energy efficiency class A (Grundfos alpha2L 25-60)
0,1 - 2,5 m³/h H: 6,0-1 m
proportional pressure control
primary ball valves, connection Rp1 (FT)
secondary connection G1A (MT)
supply temperature sensor
outdoor temperature sensor (install. on buildingsite)
3-15 kW
max. 90° primary, max. 60° secondary, max. 10 bar
Item no. Description unit
1048782Uponor Central Pump group CPG 15with controller 1 pcs
Uponor Central Pump group CPG 15 without
controller
installation in boiler rooms ,
without actuator, without control ,
for connection to external boiler control or connection to Uponor climate
controller C-46 heating/cooling,
requires Motor 1002356 or 1002357
3-way-mixing valve, for motor drive 1002356 or 1002357
kvs 6,3
pump energy efficiency class A (Grundfos alpha2L 15-60)
Q: 0,1-2,5 m³/h, H: 6-2,4 m
proportional pressure control
primary connection Rp1 (FT)
secondary ballvalves, connection Rp1 (FT)
3-15 kW
max. 90° primary, max. 60° secondary, max. 10 bar
Item no. Description unit
1048783Uponor Central Pumpgroup CPG 15without controller 1 pcs
EEI-Int-RHC-01.1270
Uponor Radiant Heating/Cooling > Uponor industrial underfloor heating
EEI-Int-RHC-01.12 71
Uponor Industrial Under� oor Heating
Uponor industrial underfl oor
heating is a low-temperature
heat distribution system for
heating industrial spaces. The
system is built directly into the
concrete fl oor slab. It is even
possible to make use of the
standard steel reinforcement
for the concrete slab as a support structure for the heating pipes.
Heat can be supplied by any conventional warm water heating
system designed for use in the type of building being in question.
Your advantages
Rapid return on investment
Total design space freedom
Optimal building space utilisation
Uniform temperature profi le
Low air speeds
No dust circulation
Stimulating working environment
No maintenance costs
Proven technology
Extensive declaration of liability
System components
Uponor industrial
clamp track
Systempipe / -Fittings Additional components Manifold / Cabinets
Uponor industrial
manifold 25-G 11/2
Uponor cable tie Uponor Q&E PPSU coupling
Uponor pipe clips Uponor Q&E brass
connection with male thread
Uponor PE-Xa pipe 25x2.3
or 20x2.0
150
/2
D
Uponor tying wire
Uponor pipe bend suport
Uponor conduit
Uponor Radiant Heating/Cooling > Uponor industrial underfloor heating
Uponor industrial � oor heating PE-Xa pipes
Uponor PE-Xa pipes
PE-Xa pipe with an oxygen diffusion barrier manufactured from peroxide
cross-linked polyethylene (PE-Xa) using the Engel method complying
with e.g. prENISO 15875 “Plastics piping systems for hot and cold water
installations - Cross-linked polyethylene” with an oxygen diffusion barrier
of EVOH (ethyl vinyl alcohol). Uponor pipes fulfil the requirements for
oxygen diffusion resistance as per DIN 4726. Malfunction temperature
95°C. Design pressure 8,8 bar (at 70°C).
Item no. d [mm] s [mm] l [m] V [l/m] Description unit
1009230 20 2.0 240 0.2Uponor pe PE-Xa Q&E pipe 20x2.0240 m coil 240 m
1009231 20 2.0 480 0.2Uponor pe PE-Xa Q&E pipe 20x2.0480 m coil 480 m
Uponor eval PE-Xa Q&E pipe in coils
Pipes manufactured from peroxide cross-linked polyethylene (PE-Xa) using
the Engel method, complying with e.g. EN ISO 15875 ”Plastics piping
systems for hot and cold water installations - Cross-linked polyethylene”.
Includes an ethylene vinyl alcohol (EVOH) oxygen barrier layer, complying
with DIN 4726, to prevent corrosion of system components. This barrier
has been specially developed to work together with Uponor Q&E fitting
technology. Classification of service conditions (including typical field of
application): Application class 4 - Underfloor heating and low temperature
radiators, malfunction temperature 95 °C. Design pressure 6 bar.
Application class 5 - high temperature radiators, malfunction temperature
95 °C. Design pressure 6 bar.
Item no. d [mm] s [mm] l [m] p [bar] Description unit
1023448 25 2.3 205 6Uponor eval PE-Xa Q&E pipe 25x2.3coil lengths 205 m 205 m
1047615 25 2.3 303 6Uponor eval PE-Xa Q&E pipe 25x2.3coil lengths 303 m 303 m
1047618 25 2.3 640 6Uponor eval PE-Xa Q&E pipe 25x2.3coil lengths 640 m 640 m
Uponor PE-Xa Q&E � ttings
Uponor Q&E PPSU coupling equal
Made of PPSU.
Note: Uponor Q&E Ring must be ordered separately!
Item no. d [mm] p [bar] Description unit
1008932 20 6+10Uponor Q&E PPSU coupling 20-20
5 pcs
1008671 25 6+10Uponor Q&E PPSU coupling 25-25
5 pcs
l
d
SWSW1
z
IG
l
d
SWSW1
z
AG
Uponor compression adapter
Compression adapter made of brass, for connection of Uponor PE-X pipes
with 3/4" female thread.
Item no. d [mm] MT ["] FT ["] l [mm] A/F [mm] z [mm] Description unit
1005295 25 R 3/4 50 37/27 15Uponor compression adapter 25x2.3-3/4"MT
10 pcs
1005296 25 Rp 1 40 37/38 8Uponor compression adapter 25x2.3-1" FT
10 pcs
1005297 25 Rp 3/4 35 37/31 8Uponor compression adapter 25x2.3-3/4 FT
10 pcs
1005298 25 R 1 53 37/34 20Uponor compression adapter 25x2.3-1" MT
10 pcs
EEI-Int-RHC-01.1272
Uponor Radiant Heating/Cooling > Uponor industrial underfloor heating
Uponor PE-Xa Q&E � ttings
Uponor Q&E brass connection with male thread
Made of DR brass. Male thread acc.to DIN EN 10226-1 for sealing in.
Note: Uponor Q&E Ring must be ordered separately!
Item no. d [mm] MT ["] p [bar] Description unit
1023006 20 R 3/4 6+10Uponor Q&E connection with male threadtaper, 20-3/4 5 pcs
1023007 25 R 3/4 6+10Uponor Q&E connection with male threadtaper, 25-3/4 5 pcs
1023008 25 R1 6+10Uponor Q&E connection with male threadtaper, 25-1 5 pcs
Uponor Q&E brass connection with female thread
Made of DR brass. Female thread acc. to DIN EN 10226-1.
Note: Uponor Q&E Ring must be ordered separately!
Item no. d [mm] FT ["] p [bar] Description unit
1023011 20 Rp 3/4 6+10Uponor Q&E connection with female thread20-3/4 5 pcs
1023012 25 Rp 3/4 6+10Uponor Q&E connection with female thread25-3/4 5 pcs
1023013 25 Rp 1 6+10Uponor Q&E connection with female thread25-1 5 pcs
Uponor Q&E ring natural
Made of PE-X. Uponor Q&E rings natural intended for Uponor Q&E
fittings. For PE-Xa pipe dimensions 16, 20, 25, 32, 40, 50 and 63 mm.
Item no. d [mm] colour [-] p [bar] Description unit
1042836 20 natural 6+10Uponor Q&E ring natural with stop edgeUponor PE-Xa dim 20 mm 20 pcs
1042840 25 natural 6+10Uponor Q&E ring natural with stop edgefor Uponor PE-Xa dim 25 mm 20 pcs
Uponor industrial � oor heating � xation and accessories
ra
d
h
l b
Uponor industrial clamp track
Uponor clamp track for fixation of Uponor PEX pipes.
Item no. w [mm] h [mm] d [mm] c/c [mm] l [mm] Description unit
1005290 50 34 25 50 3000Uponor clamp track for 25 mm pipes
30 m
1005358 40 26 20 50 3000Uponor clamp track for 20 mm pipes
30 m
Uponor fastening nail
For fastening the Uponor clamp track 25
Item no. w [mm] h [mm] Description unit
1005291 36 50Uponor fastening nail forindustrial floor heating clamp track 500 pcs
EEI-Int-RHC-01.12 73
Uponor Radiant Heating/Cooling > Uponor industrial underfloor heating
Uponor industrial � oor heating � xation and accessories
Uponor pipe clips
For fastening Uponor pipes on reinforcement steel meshes.
Item no. h [mm] h1 [mm] w [mm] d [mm] d1 [mm] Description unit
1005289 57 27 38 25 3-8Uponor pipe clipsfor PE-Xa pipe 25x2.3 250 pcs
Uponor cable tie
For fastening Uponor pipes on reinforcement steel meshed.
Made of polyamide.
Item no. w [mm] l [mm] Description unit
1005287 5 200Uponor cable ties, length 200 mmfor the pipe assembly on support mats 100 pcs
1005372 7 280Uponor cable ties, length 280 mmfor the pipe assembly on support mats 100 pcs
Uponor tying wire
For fastening Uponor pipes on reinforcement steel meshes. Made of steel.
250 pcs per bag.
Item no. Description unit
1009222Uponor tying wire, 150 x 1.25
250 pcs
Uponor pipe bend support
Made of galvanized steel as bend support for the pipes in the manifold
area.
Item no. d [mm] Description unit
1009233 20Uponor pipe bend support20 mm 50 pcs
1009006 25Uponor pipe bend support22-25 mm 20 pcs
Uponor conduit
Corrugated, fire classification E conforming to DIN EN 13501-1. Supplied
in coils.
Item no. d [mm] d1 [mm] d2 [mm] colour [-] Description unit
1012869 35/29 25 blackUponor conduit black 35/29 MLC 25
50 m
EEI-Int-RHC-01.1274
Uponor Radiant Heating/Cooling > Uponor industrial underfloor heating
Uponor industrial � oor heating manifold and accessories
Uponor industrial manifold 25-G 11/2
Uponor Industrial Manifold 25-G 11/2
as supply / return for Industrialheating, made of:
- supply-segment, with control valves for preadjustment, heating loop
connection for PE-Xa Pipe 25x2,3 with compression adapter.
- return-segment with thermostat upper section incl. cap for locking,
Uponor actuator can be mounted directly on the return manifold , heating
loop connection for PE-Xa Pipe 25x2,3 with compression adapter
Spacing of outlet: 100 mm
Material: fibreglass reinforced Polyamid
max. operating temperatur: 60 °C
max. operating pressure 6 bar
induvidual combination up to 20 loops max.
Number of needed brackets
loops 2-5 6-9 10-14 15-19 20
bracket 2 3 4 5 6
Item no. Description unit
1045813Uponor industrial manifold 25-G 1 1/2"
1 set
Uponor industrial manifold G3/4 Eurcone
as supply / return for Industrialheating, made of:
- supply-segment, with control valves for preadjustment, heating loop
connection for G3/4 eurocone.
- return-segment with thermostat upper section incl. cap for locking,
Uponor actuator can be mouinted directly on the return manifold , heating
loop connection for G3/4 eurocone.
Spacing of outlet: 100 mm
Material: fibreglass reinforced Polyamid
max. operating temperatur: 60 °C
max. operating pressure: 6 bar
induvidual combination up to 20 loops max.
Quantity necesary bracket
loops 2-5 6-9 10-14 15-19 20
bracket 2 3 4 5 6
Item no. Description unit
1045814Uponor industrial manifold G3/4 eurocone
1 set
Uponor industrial manifold basic kit
Uponor Industrial Manifold Basic Kit
for mounting the industrial manifold, made of:
- 2 St. brackets short
- 2 St. brackets long
- 2 St. filling valve brass
- 2 St. thermometer 0 - 60°C
- 1 St. manometer
- 2 St. endcap
- 2 St. flat sealing screw connection piece with swivel nut
- 1 St. mounting material: 8x screws 6x60mm
8x plastic anchor 8x40mm
2x flat sealing 44x32x2
Item no. Description unit
1045815Uponor industrial manifold basic kit
1 set
EEI-Int-RHC-01.12 75
Uponor Radiant Heating/Cooling > Uponor industrial underfloor heating
Uponor industrial � oor heating manifold and accessories
Uponor industrial manifold bracket kit
Uponor Industrial Manifold Bracket Kit
for mounting the Industrial manifold, made of:
- 2 St. brackets short
- 2 St. brackets long
- 1 St. mounting material: 8x screws 6x60mm
8x plastic anchor 8x40mm
Item no. Description unit
1045816Uponor industrial manifold bracket kit
1 set
Uponor industrial flowmeter
Uponor Industrial Flowmeter
For adjusting the water quantity of the individual heating loops in a range
of 4 -20 l/min. Water quantity is indicated in the inspection window. With
shut-off function. Made of fibre-glass reinforced polyamid.
Material: fibreglass reinforced Polyamid
Item no. Description unit
1030134Uponor industial flowmeter
1 pcs
Uponor industrial ball valve G 11/2
Uponor Industrial Ball Valve G 11/2
for use with the Uponor Industrial manifold G 11/2
connection:
- G 11/2 FT
- G 11/2 MT
Material: brass
Item no. Description unit
1030135Uponor industrial ball valve G 1 1/2"
1 set
EEI-Int-RHC-01.1276
Uponor Radiant Heating/Cooling > Uponor snow and ice melting
EEI-Int-RHC-01.12 77
Uponor snow and ice melting
Uponor snow and ice melting
system is best suitable for all
outside surfaces which are
provided with a solid covering.
It will be especially used for
driveways, ramps, fi re
department or hospital
approach roads, helicopter
landing zones, sidewalks, football pitches, etc..
Your advantages
System ensures a maximum of security - round the clock
Automatically deicing, no more shoveling of snow
Avoids environmental stress and damage through de-icing
salt
Usage of industrial waste heat possible
Fast and easy installation with robust Uponor PE-X pipes
Complete system with all components available
Reduces slip and fall liability
System components Systempipe / -Fittings Additional components Manifold / Cabinets
Uponor compression
adapter
PE-X
Uponor industrial clamp
track
Uponor Manifolds
Uponor fastening nail
Uponor Supply pipes
Uponor tying wire
Uponor supply accessories
Uponor electrofusion
fi tting
Uponor snow and ice melting
pipe 25x2.3
D
Uponor cable tie Uponor pipe bend suport
Uponor conduit
Uponor Radiant Heating/Cooling > Uponor snow and ice melting
Uponor snow and ice melting pipes
Uponor snow and ice melting pipe
Uponor snow and ice melting pipes manufactured from cross-linked
polyethylene, complying with e.g. EN ISO 15875 ”Plastics piping
systems for hot and cold water installations - Cross-linked polyethylene”.
Application for underfloor heating up to 50 °C water temperature
Design pressure 4 bar.
Item no. Description unit
1022341Uponor Meltaway PE-X pipe 25x2.3920 m 920 m
1033625Uponor Meltaway PE-X pipe 25x2.31020 m 1020 m
1033626Uponor Meltaway PE-X pipe 25x2.3other lengths <1000m 1 m
Uponor snow and ice melting manifold and accessories
Uponor manifolds
Uponor snow and ice melting single manifold made of high density
polyethylene (HDPE) pipe and equipped with compact-welded couplings.
Couplings between centres are 500mm.
Item no. Description unit
1033637Uponor Meltaway manifold 10 waysingle outlet, C/C 600 75 6m 1 pcs
1033638Uponor Meltaway manifold 10 waysingle outlet, C/C 600 110 6m 1 pcs
1033639Uponor Meltaway manifold 10 waysingle outlet, C/C 600 160 6m 1 pcs
1033640Uponor Meltaway manifold 40 waysingle outlet, C/C 150 75 6m 1 pcs
1033641Uponor Meltaway manifold 30 waysingle outlet, C/C 200 75 6m 1 pcs
1033642Uponor Meltaway manifold 30 waysingle outlet, C/C 200 110 6m 1 pcs
1033643Uponor Meltaway manifold 30 waysingle outlet, C/C 200 160 6m 1 pcs
1033645Uponor Meltaway manifold 40 waysingle outlet, C/C 150 110 6m 1 pcs
1033647Uponor Meltaway manifold 40 waysingle outlet, C/C 150 160 6m 1 pcs
Uponor manifolds
Uponor snow and ice melting single manifold made of high density
polyethylene (HDPE) pipe and equipped with compact-welded couplings.
Couplings between centres are 500mm.
Item no. Description unit
1033631Uponor Meltaway manifold 12 waysingle outlet, C/C 500 75 6m 1 pcs
1033632Uponor Meltaway manifold 12 waysingle outlet, C/C 500 110 6m 1 pcs
1033633Uponor Meltaway manifold 12 waysingle outlet, C/C 500 160 6m 1 pcs
EEI-Int-RHC-01.1278
Uponor Radiant Heating/Cooling > Uponor snow and ice melting
Uponor snow and ice melting manifold and accessories
Uponor manifolds
Uponor snow and ice melting double manifold made of high density
polyethylene (HDPE) pipe and equipped with compact-welded couplings
oriented in two directions with an angle of 120° between them.
Item no. Description unit
1033634Uponor Meltaway manifold 12 waydouble outlet, C/C 500 75 6m 1 pcs
1033635Uponor Meltaway manifold 12 waydouble outlet, C/C 500 110 6m 1 pcs
1033636Uponor Meltaway manifold 12 waydouble outlet, C/C 500 160 6m 1 pcs
1033646Uponor Meltaway manifold 40 waydouble outlet, C/C 150 110 6m 1 pcs
1033644Uponor Meltaway manifold 40 waydouble outlet, C/C 150 75 6m 1 pcs
Uponor coupling
Uponor straight couplings for snow and ice melting PE-X pipes 25x2.3
Made of HDPE.
Item no. Description unit
1033672Uponor Meltaway coupling 25x2.3 mmshort, 145 mm 1 pcs
1033678Uponor Meltaway coupling 25x2.3 mmlong, 290 mm 1 pcs
Uponor supply pipes
Uponor snow and ice melting supply pipes made of HDPE.
Item no. Description unit
1033628Uponor HDPE supply pipe 75x6.8 mmL=6000 mm 1 m
1033629Uponor HDPE supply pipe 110x6.6 mmL=6000 mm 1 m
1033630Uponor HDPE supply pipe 160x9.5 mmL=6000 mm 1 m
Uponor supply pipes tees
Uponor snow and ice melting tees made of HDPE.
Item no. Description unit
1033648Uponor tee 75
1 pcs
1033649Uponor tee 110
1 pcs
1033650Uponor tee 160
1 pcs
EEI-Int-RHC-01.12 79
Uponor Radiant Heating/Cooling > Uponor snow and ice melting
Uponor snow and ice melting manifold and accessories
Uponor supply pipes elbows
Uponor snow and ice melting elbows made of HDPE.
Item no. Description unit
1033652Uponor elbow 75 x 90°
1 pcs
1033653Uponor elbow 110 x 90°
1 pcs
1033654Uponor elbow 160 x 90°
1 pcs
Uponor supply pipes reducer
Uponor snow and ice melting reducer made of HDPE.
Item no. Description unit
1056656Uponor reducer 110-75
1 pcs
1033657Uponor reducer 160 - 110
1 pcs
Uponor supply pipes end cap
Uponor snow and ice melting end cap made of HDPE.
Item no. Description unit
1033659Uponor end cap 75
1 pcs
1033660Uponor end cap 110
1 pcs
1033661Uponor end cap 160
1 pcs
Uponor flange support
Uponor snow and ice melting flange support for connection of Uponor
flange to supply/return pipes. Made of HDPE.
Item no. Description unit
1033662Uponor flange support 75
1 pcs
1033663Uponor flange support 110
1 pcs
1052123Uponor flange support 160
1 pcs
EEI-Int-RHC-01.1280
Uponor Radiant Heating/Cooling > Uponor snow and ice melting
Uponor snow and ice melting manifold and accessories
Uponor flange
Uponor snow and ice melting flange made of HDPE.
Item no. Description unit
1033666Uponor flange 75x6.8 mm
1 pcs
1033667Uponor flange 110x6.6 mm
1 pcs
1033668Uponor flange 160x9.5 mm
1 pcs
Uponor electrofusion fitting
Uponor snow and ice melting electrofusion fittings made of HDPE.
Item no. Description unit
1033673Uponor electrofusion fittingfor pipe 75x6.8 mm 1 pcs
1033675Uponor electrofusion fittingfor pipe 110x6.6 mm 1 pcs
1033676Uponor electrofusion fittingfor pipe 160x9.5 mm 1 pcs
ra
d
h
l b
Uponor industrial clamp track
Uponor clamp track for fixation of Uponor PEX pipes.
Item no. w [mm] h [mm] d [mm] c/c [mm] l [mm] Description unit
1005290 50 34 25 50 3000Uponor clamp track for 25 mm pipes
30 m
Uponor fastening nail
For fastening the Uponor clamp track 25
Item no. w [mm] h [mm] Description unit
1005291 36 50Uponor fastening nail forindustrial floor heating clamp track 500 pcs
Uponor cable tie
For fastening Uponor pipes on reinforcement steel meshed.
Made of polyamide.
Item no. w [mm] l [mm] Description unit
1005287 5 200Uponor cable ties, length 200 mmfor the pipe assembly on support mats 100 pcs
1005372 7 280Uponor cable ties, length 280 mmfor the pipe assembly on support mats 100 pcs
EEI-Int-RHC-01.12 81
Uponor Radiant Heating/Cooling > Uponor snow and ice melting
Uponor snow and ice melting manifold and accessories
Uponor tying wire
For fastening Uponor pipes on reinforcement steel meshes. Made of steel.
250 pcs per bag.
Item no. Description unit
1009222Uponor tying wire, 150 x 1.25
250 pcs
Uponor pipe bend support
Made of galvanized steel as bend support for the pipes in the manifold
area.
Item no. d [mm] Description unit
1009006 25Uponor pipe bend support22-25 mm 20 pcs
Uponor conduit
Corrugated, fire classification E conforming to DIN EN 13501-1. Supplied
in coils.
Item no. d [mm] d1 [mm] d2 [mm] colour [-] Description unit
1012869 35/29 25 blackUponor conduit black 35/29 MLC 25
50 m
l
d
SWSW1
z
IG
l
d
SWSW1
z
AG
Uponor compression adapter
Compression adapter made of brass, for connection of Uponor PE-X pipes
with 3/4" female thread.
Item no. d [mm] MT ["] FT ["] l [mm] A/F [mm] z [mm] Description unit
1005297 25 Rp 3/4 35 37/31 8Uponor compression adapter 25x2.3-3/4 FT
10 pcs
1005296 25 Rp 1 40 37/38 8Uponor compression adapter 25x2.3-1" FT
10 pcs
1005295 25 R 3/4 50 37/27 15Uponor compression adapter 25x2.3-3/4"MT
10 pcs
1005298 25 R 1 53 37/34 20Uponor compression adapter 25x2.3-1" MT
10 pcs
Uponor chamfering tool
For de-studding the Uponor snow and ice melting pipe.
Item no. Description unit
1033689Uponor Meltaway chamfering toolfor Uponor Meltaway 25 mm pipe 1 pcs
EEI-Int-RHC-01.1282
Uponor Radiant Heating/Cooling > Uponor sport floor heating
EEI-Int-RHC-01.12 83
Uponor sports � oor heating
Uponor radiant heating system
for surface elastic fl oors. These
fl oors are a synthesis of woo-
den swing fl oors with elastic
layer made of PVC or linoleum.
The heating registers runs in
pipe holders (Patent Uponor)
directly under the blind fl oor.
The pipes are to be connected to distribute- /collector pipes.
Uponor sports fl oor heating systems are quick installed. First due
to the fl exible and at the same time robust PE-Xa pipe material.
Secondly due to the patented mounting principle for swing fl oor
constructions.
Your advantages
Sports fl oor heating systems off er high thermal comfort
Provides mild radiant heat and an even temperature
distribution with low air speed
Gives athletes and architectures all freedom, because the
system is invisible
Takes all hygienic and physiologic requirements of sports
halls into consideration
Energy saving due to operation with low heating water
temperatures
System components
Uponor pipe fi xation
Systempipe / -Fittings
Uponor eval PE-Xa pipe in
coils
Additional components Manifold / Cabinets
Uponor Q&E tichelmann
manifold for sportsfl oor UFH
Uponor pipe fi xation
double
sprung fl oors
Uponor pipe bend suport
Uponor conduit
Uponor Radiant Heating/Cooling > Uponor sport floor heating
Uponor sport � oor PE-Xa pipes
Uponor eval PE-Xa Q&E pipe in coils
Pipes manufactured from peroxide cross-linked polyethylene (PE-Xa) using
the Engel method, complying with e.g. EN ISO 15875 ”Plastics piping
systems for hot and cold water installations - Cross-linked polyethylene”.
Includes an ethylene vinyl alcohol (EVOH) oxygen barrier layer, complying
with DIN 4726, to prevent corrosion of system components. This barrier
has been specially developed to work together with Uponor Q&E fitting
technology. Classification of service conditions (including typical field of
application): Application class 4 - Underfloor heating and low temperature
radiators, malfunction temperature 95 °C. Design pressure 6 bar.
Application class 5 - high temperature radiators, malfunction temperature
95 °C. Design pressure 6 bar.
Item no. d [mm] s [mm] l [m] p [bar] Description unit
1023448 25 2.3 205 6Uponor eval PE-Xa Q&E pipe 25x2.3coil lengths 205 m 205 m
1047615 25 2.3 303 6Uponor eval PE-Xa Q&E pipe 25x2.3coil lengths 303 m 303 m
1047618 25 2.3 640 6Uponor eval PE-Xa Q&E pipe 25x2.3coil lengths 640 m 640 m
Uponor sport � oor PE-Xa Q&E � ttings
Uponor Q&E PPSU coupling equal
Made of PPSU.
Note: Uponor Q&E Ring must be ordered separately!
Item no. d [mm] p [bar] Description unit
1008671 25 6+10Uponor Q&E PPSU coupling 25-25
5 pcs
Uponor Q&E brass connection with male thread
Made of DR brass. Male thread acc.to DIN EN 10226-1 for sealing in.
Note: Uponor Q&E Ring must be ordered separately!
Item no. d [mm] MT ["] p [bar] Description unit
1023007 25 R 3/4 6+10Uponor Q&E connection with male threadtaper, 25-3/4 5 pcs
1023008 25 R1 6+10Uponor Q&E connection with male threadtaper, 25-1 5 pcs
Uponor Q&E brass connection with female thread
Made of DR brass. Female thread acc. to DIN EN 10226-1.
Note: Uponor Q&E Ring must be ordered separately!
Item no. d [mm] FT ["] p [bar] Description unit
1023012 25 Rp 3/4 6+10Uponor Q&E connection with female thread25-3/4 5 pcs
1023013 25 Rp 1 6+10Uponor Q&E connection with female thread25-1 5 pcs
Uponor Q&E ring natural
Made of PE-X. Uponor Q&E rings natural intended for Uponor Q&E
fittings. For PE-Xa pipe dimensions 16, 20, 25, 32, 40, 50 and 63 mm.
Item no. d [mm] colour [-] p [bar] Description unit
1042840 25 natural 6+10Uponor Q&E ring natural with stop edgefor Uponor PE-Xa dim 25 mm 20 pcs
EEI-Int-RHC-01.1284
Uponor Radiant Heating/Cooling > Uponor sport floor heating
Uponor sport � oor � xation and accessories
Uponor pipe fixation
For exact leading of pipes inside the channels of sport floor
Material: Polyamid
Item no. l [mm] sd [mm] c/c [mm] l1 [mm] h [mm] Description unit
1005286 290 45 100 145 50Uponor pipe clip trackfor floors in gyms. Polyamid 25 pcs
Uponor pipe fixation double
For exact leading of pipes in the bending zone of chanels of sport floor
Material: galvanised steel
Item no. l1 [mm] c/c [mm] l [mm] Description unit
1005284 105 100 975Uponor double pipe clip track for floorsin gyms. galvanised steel 1 pcs
Q&E tichelmann manifold 2 circuits for sportsfloor
UFH
as manifold for the use in sportsfl oor UFH systems according to
theTichelmann principle. For connection of Uponor PE-Xa pipes
25x2.3mmwith Uponor Q&E connection technology consisting of:-
1 manifold (distributor & collector)- 4 Q&E rings 25- 2 Q&E rings
40Material: Uponor eval PE-Xa pipes + Uponor PPSU fittings.
Item no. d [mm] l [mm] c/c [mm] Description unit
1046747 40 2084 150Uponor Q&E tichelmann manifold2 circuits for sportsfloor UFH 1 set
Q&E tichelmann manifold for sportsfloor UFH
as manifold for the use in sportsfloor UFH systems according to the
Tichelmann principle. For connection of Uponor PE-Xa pipes 25x2.3mm
with Uponor Q&E connection technology consisting of:
- 1 manifold (distributor & collector)
- 6 Q&E rings 25
- 2 Q&E rings 40
Material: Uponor eval PE-Xa pipes + Uponor PPSU fittings
Item no. d [mm] l [mm] c/c [mm] Description unit
1046748 40 2084 150Q&E tichelmann manifold for sportsfloor UFH
1 set
Q&E tichelmann manifold end segment for
sportsfloor UFH
as manifold for the use in sportsfloor UFH systems according to the
Tichelmann principle. For connection of Uponor PE-Xa pipes 25x2.3mm
with Uponor Q&E connection technology consisting of:
- 1 manifold (distributor & collector)
- 6 Q&E rings 25
Material: Uponor eval PE-Xa pipes + Uponor PPSU fittings
Item no. d [mm] l [mm] c/c [mm] Description unit
1046749 40 2036 150Q&E tichelmann manifold end segmentfor sportsfloor UFH 1 set
EEI-Int-RHC-01.12 85
Uponor Radiant Heating/Cooling > Uponor sport floor heating
Uponor sport � oor � xation and accessories
Uponor eval PE-Xa pipes in straight lengths
Pipes manufactured from peroxide cross-linked polyethylene (PE-Xa) using
the Engel method, complying with e.g. EN ISO 15875 ”Plastics piping
systems for hot and cold water installations - Cross-linked polyethylene”.
Includes an ethylene vinyl alcohol (EVOH) oxygen barrier layer, complying
with DIN 4726, to prevent corrosion of system components. This barrier
has been specially developed to work together with Q&E fitting technology.
Classification of service conditions (including typical field of application):
Application class 4 - Underfloor heating and low temperature radiators,
malfunction temperature 95 °C. Design pressure 6 bar. Application class
5 - High temperature radiators, malfunction temperature 95 °C. Design
pressure 6 bar.
Item no. d [mm] s [mm] l [m] p [bar] Description unit
1008939 40 3.7 6 6Uponor eval PE-Xa Q&E pipe40x3.7 mm in straight lengths of 6 m 6 m
Uponor Q&E PPSU coupling equal
Made of PPSU.
Note: Uponor Q&E Ring must be ordered separately!
Item no. d [mm] p [bar] Description unit
1008673 40 6Uponor Q&E PPSU coupling 40-40
1 pcs
Uponor Q&E PPSU elbow 90°
Made of PPSU.
Note: Uponor Q&E Ring must be ordered separately!
Item no. d [mm] p [bar] Description unit
1008683 40 6Uponor Q&E PPSU elbow 90° 40-40
1 pcs
Uponor Q&E ring natural
Made of PE-X. Uponor Q&E rings natural intended for Uponor Q&E
fittings. For PE-Xa pipe dimensions 16, 20, 25, 32, 40, 50 and 63 mm.
Item no. d [mm] colour [-] p [bar] Description unit
1045464 40 natural 6Uponor Q&E ring natural with stop edgefor Uponor PE-Xa dim 40 mm 5 pcs
Uponor Q&E brass connection with female thread
Made of DR brass. Female thread acc. to DIN EN 10226-1.
Note: Uponor Q&E Ring must be ordered separately!
Item no. d [mm] FT ["] p [bar] Description unit
1047867 40 Rp 1 1/4 6Uponor Q&E connection with female thread40-1 1/4 1 pcs
EEI-Int-RHC-01.1286
Uponor Radiant Heating/Cooling > Uponor sport floor heating
Uponor sport � oor � xation and accessories
Uponor pipe bend support
Made of galvanized steel as bend support for the pipes in the manifold
area.
Item no. d [mm] Description unit
1009006 25Uponor pipe bend support22-25 mm 20 pcs
Uponor conduit
Corrugated, fire classification E conforming to DIN EN 13501-1. Supplied
in coils.
Item no. d [mm] d1 [mm] d2 [mm] colour [-] Description unit
1012869 35/29 25 blackUponor conduit black 35/29 MLC 25
50 m
EEI-Int-RHC-01.12 87
Uponor Radiant Heating/Cooling > Uponor comfort panel
EEI-Int-RHC-01.1288
Uponor Comfort Panel
Your advantages
cooling power up to 92.5 W/m² with 10K under
temperature
Heating power up to 82.5 W/m² with 15 K under
temperature
Compatible with existing metal rail constructions
easy to install
quick installation
concealed installation/integrated in the ceiling structure
easily retrofi tted into existing ceiling structure
excellent for both new buildings and refurbishment
easy to operate
maintenance-free.
System components
Uponor Comfort Panel
Systempipe / -Fittings
Uponor PE-X Pipe 10x1.5
Additional components
Uponor Dynamic volume fl ow
controller
Manifold / Cabinets
Uponor Slip ConnectorUponor blind panel
Uponor connection MLC
Uponor connection with
female threat
The Uponor comfort panel is a
suspended ceiling system which
can be used for heating and
cooling. The system consist of
thermally activated ceiling
panels which can be installed
fast and easy into conventional
suspended ceiling grids.
Uponor Radiant Heating/Cooling > Uponor comfort panel
Uponor comfort panel
b
l h
Uponor comfort panel
For cooling and heating of buildings with suspended raster frame ceiling.
For already existing or new raster frames under the ceiling. With optically
sophisticated surface from fleece coated steel sheet. High performance due
to optimised thermal conductivity between surface and integrated pipes,
made of PE-X, with thermal insulation made of mineral fibres.
Cooling capacity 74 W/m² by 8 K temperature difference complies with
EN 14240
Heating capacity 103 W/m² by 15 K temperature difference complies with
EN 14037
Item no. l [mm] w [mm] h [mm] Description unit
1045315 1240 615 23Uponor comfort panel 1250 x 625
1 pcs
1045316 1190 590 23Uponor comfort panel 1200 x 600
1 pcs
b
l h
Uponor comfort panel
For cooling and heating of buildings with suspended raster frame ceiling.
For already existing or new raster frames under the ceiling. With optically
sophisticated surface from fleece coated steel sheet. High performance due
to optimised thermal conductivity between surface and integrated pipes,
made of PE-X, with thermal insulation made of mineral fibres.
Cooling capacity 74 W/m² by 8 K temperature difference complies with
EN 14240
Heating capacity 103 W/m² by 15 K temperature difference complies with
EN 14037
Item no. l [mm] w [mm] h [mm] Description unit
1045317 615 615 23Uponor comfort panel 625 x 625
1 pcs
1045318 590 590 23Uponor comfort panel 600 x 600
1 pcs
EEI-Int-RHC-01.12 89
Uponor Radiant Heating/Cooling > Uponor comfort panel
Uponor comfort panel - accessories
b
l h
Uponor blind panel
For use in on-site installed suspended raster ceilings. With optically
sophisticated surface from fleece coated mineral faser board, optically fits
exactly to comfort panel.
Colour from below: white
Acoustical absorption (alpha w): 1,00
Acoustical absorption (NRC): 0,95
Building material class according to DIN 4102: A1
Item no. l [mm] w [mm] h [mm] A [m²] Weight [kg] Description unit
1022983 1242 617 18 0.76 2.08Uponor Blind Panel 625dimension 617 x 1242 x 18 16 pcs
1022984 1195 595 18 0.71 1.93Uponor Blind Panel 600dimension 595 x 1195 x 18 16 pcs
b
l h
Uponor blind panel
For use in on-site installed suspended raster ceilings. With optically
sophisticated surface from fleece coated mineral faser board, optically fits
exactly to comfort panel.
Colour from below: white
Acoustical absorption (alpha w): 1,00
Acoustical absorption (NRC): 0,95
Building material class according to DIN 4102: A1
Item no. l [mm] w [mm] h [mm] Description unit
1045319 615 615 18Uponor Blind Panel 625 x 625
32 pcs
1045320 590 590 20Uponor Blind Panel 600 x 600
32 pcs
l
b Uponor blind frame
For use in existing suspended ceiling constructions for optical devision into
a quadratic raster.
Item no. l [mm] w [mm] colour [-] Description unit
1045323 625 24 whiteUponor blind frame 625, white
1 pcs
1045324 600 24 whiteUponor blind frame 600, white
1 pcs
EEI-Int-RHC-01.1290
Uponor Radiant Heating/Cooling > Uponor comfort panel
Uponor comfort panel - accessories
Uponor PE-X pipe 10 x 1,5 mm
As pipe in coils for connection or extension between 2 comfort panels.
Material: Uponor PEX pipe from high pressure cross-linked polyethylene
Medium: heating/cooling water acc. to VDI 2035 or water-glycol up to
50%
Temperature range: 0 to 60°C
Pressure range: 0 to 6 bar by max. 65 °C
0 to 12 bar by max. 20 °C
Surrounding humidity: up to 90%
Material: plastic
Item no. d [mm] s [mm] l [m] Description unit
1045327 10 1.5 100Uponor PE-X pipe 10 x 1,5 mm, in coilsbarrier, 10x1,5 coil 100m, 6bar 100 m
b
d
Uponor pipe insert, for 10x1,5 PE-X pipe
Pipe sleeve made of plastic, for plug in PE-X pipe ends,
dimension 10 x 1,5 mm, for stiffening of a pipe in connection area with
Uponor slip-connector.
Item no. w [mm] d [mm] Description unit
1045328 5 7Uponor support sleeve, 10 x 1,5 mm
10 pcs
l
d
Uponor slip-connector
Push-in fitting for connection of more comfort panels together into one
control circuit or to one ceiling panel area.
Medium: heating/cooling water acc. to VDI 2035 or water-glycol up to
50%
Temperature range: 0 to 60 °C
Pressure range: 0 to 6 bar by max. 65 °C
Surrounding humidity: up to 90%
Material: plastic
Item no. l [mm] d [mm] Description unit
1045325 45 22Uponor slip-connector equal 10 mm
100 pcs
1022987 60 15Uponor slip connector equal 15 mm
10 pcs
l
d3 d2d1
Uponor slip-connector reduced 15-10 mm
Push-in fitting for connection of more comfort panels together into one
control circuit or to one ceiling panel area.
Medium: heating/cooling water acc. to VDI 2035 or water-glycol up to
50%
Temperature range: 0 to 60 °C
Pressure range: 0 to 6 bar by max. 65 °C
Surrounding humidity: up to 90%
Material: plastic
Item no. l [mm] d1 [mm] d2 [mm] d3 [mm] Description unit
1045326 56 32 10 15Uponor slip-connector reduced 15-10 mm
100 pcs
l
d
Uponor Stop plug 15
as end plug 15 mm, for closing of capillary mats ends
Material: nickel-plated brass
Item no. d [mm] l [mm] Description unit
1000296 15 35Uponor stop plug 15
10 pcs
EEI-Int-RHC-01.12 91
Uponor Radiant Heating/Cooling > Uponor comfort panel
Uponor comfort panel - accessories
63,9
ø 51
,4
Uponor Diversion Fitting Dim Cu 22 – 4x Dim 10
push-in (CPII Manifold)
Uponor Diversion Fitting Dim Cu 22 – 4x Dim 10 push-in allows the
connection of four series of panels to a MLC 20 mm pipe using an Uponor
Press Adapter MLC 20-22CU (item number 1014558).
Temperature range: 0 – 60°C
Pressure range: 0-6 bar
Material: plastic
Item no. Description unit
1048684Uponor Diversion Fitting Dim. Cu 224x Dim 10 push-in 1 pcs
35
18
ø 10
ø 10
± 0
,1
Uponor Endplug Dim 10 push-in
Uponor Endplug Dim 10 push-in to close an open distribution line from the
Uponor diversion fitting Cu 22 – 4x 10 mm push-in (1048684)
Temperature range: 1 – 60°C
Pressure range: 0-6 bar
Material: plastic
Item no. Description unit
1048685Uponor Endplug Dim 10 push-in
1 pcs
l
d d1
Uponor connection MLC
For connection of 15 mm push-in system to Uponor MLC pipe.
Material: nickel-plated brass, press sleeve
Item no. d [mm] d1 [mm] l [mm] Description unit
1000297 15 16x2.0 70Uponor connectionto MLCP 15-16x2 6 pcs
1000298 15 20x2.25 70Uponor connectionto MLCP 15-20x2.25 6 pcs
d
l
AG
Uponor connection with male threat
for connection of 15 mm push-in system to male threat.
Material: nickel-plated brass
Item no. d [mm] MT ["] l [mm] Description unit
1000299 15 R 1/2 57Uponor connectionwith male threat 15-1/2 MT 6 pcs
1000300 15 R 3/4 57Uponor connectionwith male threat 15-3/4 MT 6 pcs
AG
l
d
Uponor push-in compression adapter
for connection of 15 mm push-in system to female threat.
Material: nickel-plated brass
Item no. d [mm] MT ["] l [mm] Description unit
1000301 15 R 1/2 41Uponor push-in compressionadapter15-1/2 FT 6 pcs
d
l
l1
d1
Uponor connection elbow
for connection of 15 mm push-in system to Uponor MLC pipe, in 90°
version.
Material: nickel-plated brass, press sleeve
Item no. d [mm] d1 [mm] l [mm] l1 [mm] Description unit
1000303 15 16x2 45 48Uponor connection elbow to UponorMLC pipes, 15-16x2 6 pcs
1000304 15 20x2.25 45 48Uponor connection elbow to UponorMLC pipes, 15-20x2,25 6 pcs
EEI-Int-RHC-01.1292
Uponor Radiant Heating/Cooling > Uponor comfort panel
Uponor comfort panel - accessories
Uponor locking ring 15
for capillary pipe 15 mm push-in fitting. Ensures the coupling against
unintended (unbeabsichtigtes) solutions of push-in connection.
Material: polypropylene
Item no. d [mm] Description unit
1000310 15Uponor locking ring 15
10 pcs
Uponor ball valve
For closing of cooling and heating areas and supply pipes.
Medium: heating/cooling water acc. to VDI 2035 or water-glycol up to
50%
Temperature range: -10 to + 110 °C
Pressure range: 0 to 10 bar
Surrounding humidity: up to 95%
Material: nickel-plated brass
Item no. l [mm] FT ["] Description unit
1022985 50 G 1Uponor ball valvedimension 1 FT - 1 FT 1 pcs
1022986 50 G 3/4Uponor ball valvedimension 3/4 FT - 3/4 FT 1 pcs
Uponor reduction
Reducer from 3/4 MT to 1/2 FT by use of tees for supply and return MLC
pipes from dimension 40 x 4 mm
Material: brass
Item no. FT ["] MT ["] Description unit
1022988 Rp 1/2 G 3/4Uponor reductiondimension 1/2 FT - 3/4 MT 10 pcs
Dynamic volume flow controller
For hydraulic control of heating and cooling loops, or zones and indvidual
control over integrated valve insert in combination with thermla actuator.
Item no. DN [mm] Description unit
1042942 15Dynamic volume flow controllerAB-QM DN 15, flow rate 55 - 275 L/H 1 pcs
1042943 20Dynamic volume flow controllerAB-QM DN 20, flow rate 180 - 900 L/H 1 pcs
1042944 25Dynamic volume flow controllerAB-QM DN 25, flow rate 340 - 1700L/H 1 pcs
1042945 32Dynamic volume flow controllerAB-QM DN 32, flow rate 640 - 3200L/H 1 pcs
Screw connection for AB-QM
Screw connection Inclusively flat sealing
Item no. Type [-] Description unit
1044809 15Screw connection for AB-QM 3/4 MT
1 pcs
1044810 20Screw connection for AB-QM 1 MT
1 pcs
1044811 25Screw connection for AB-QM 1 1/4 MT
1 pcs
1044812 32Screw connection for AB-QM 1 1/2 MT
1 pcs
EEI-Int-RHC-01.12 93
[l/h] stroke [mm] [-]
90-450 2.25 G 3/4" A
180-900 2.25 G 1" A
340-1700 2.25 G 1 1/4" A
640-3200 2.25 G 1 1/2" A
FT ["] MT ["]
Rp 3/4" R 1/2"
Rp 1" R 3/4"
Rp 1 1/4" R 1"
Rp 1 1/2" R 1 1/4"
Uponor Radiant Heating/Cooling > Uponor comfort panel
Uponor comfort panel - accessories
Thermal actuator TWA -Z NO
For control of pressure indipendent volume flow controller - openes when
idle.
Item no. Type [-] [-] Description unit
1042946 TWA-Z NOThermal actuator TWA -Z NO
1 pcs
Thermal actuator TWA -Z NC
For control of pressure indipendent volume flow controller - closes when
idle.
Item no. Type [-] [-] Description unit
1042947 TWA-Z NCThermal actuator TWA -Z NC
1 pcs
l
l1
h
Uponor room temperature controller H/C
Concealed device, protects cooling surface from condensation. The TR
2/3 (concealed device) can both to control one valve (heating or cooling)
and also be switched over internally to control thus 2 valves (heating
and cooling). With an option of external setpoint remove access will it
be introduced in two-line (heating and cooling) and three-line systems
(heating and cooling). The actual operation status (heating/cooling/
dew point warning) will be show on device by means of light diods. For
simplification of wiring and installation of room temperature are switch
boxes shall be provided.
Operational voltage: 24 V / 50-60 Hz
Control range: 5-30 °C
Switching hysteresis: 1 K
Temperature sensor: NTC
Switch outlet: Triac, 24 V/1 A, short-term up to 2,5 A
Functions:
Heating or cooling
Heating or cooling with switchover
Heating and/or cooling with setpoint remot access
Installation site: concealed under plaster, fits into UP-Doses acc. to
DIN 49073
Installation depth: 28 mm
Colour: RAL 9010, pure white
Item no. l [mm] l1 [mm] h [mm] Description unit
1000311 71 70 28Uponor room thermostatTR 2/3 1 pcs
EEI-Int-RHC-01.1294
Uponor Radiant Heating/Cooling > Uponor comfort panel
Uponor comfort panel - accessories
Uponor dew point sensor
For plastered ceilings or walls / pipe installation, detects a potential
condensation arising on the pipe or in the immediate vicinity by changing
its electrical resistance. This change of resistance in the sensor is detected
by room thermostat TR 2/3, which closes control valve and effectively
protects the cooling surface from condense damage.
The dew point sensor TF 3 PR is designed for installation in plastered
ceilings (P) and for cold-water pipe conduits (R).
Installation site: plastered ceilings/walls or pipe installations
Item no. l [mm] w [mm] h [mm] Description unit
1000312 70 20 7Uponor dew point sensorTF 3 PR 1 pcs
Uponor dew point sensor
For gypsum plasterboard ceilings / suspended metal ceilings, detects a
potential condensation arising on the pipe or in the immediate vicinity by
changing its electrical resistance. This change of resistance in the sensor
is detected by room thermostat TR2/3, which closes control valve and
effectively protects the cooling surface from condense damage.
The dew point sensor TF 3 GM is designed for installation in gypsum
plasterboard ceilings/walls (G) and for suspended metal ceilings (M).
Installation site: gypsum plasterboard ceilings/walls or suspended metal
ceiling
Item no. l [mm] w [mm] h [mm] Description unit
1000313 70 20 7Uponor dew point sensorTF 3 GM 1 pcs
l
b h Uponor dew point converter
Evaluates the information received from the corresponding dew point
sensor. The integrated contact is activated when the dew point is reached.
This information can be used, for example, for remote communications with
an onsite central building control system or similar device. Up to five dew
point sensors can be assigned to each converter.
Operating voltage: 24 V / 50-60 Hz
Switch outlet: potential free switch over contact max. load capacity of the
outlet: 48 V~/60 V DC
Installation site: automation cabinet or electric manifold installation
Item no. l [mm] w [mm] h [mm] Description unit
1000314 85 36 60Uponor dew-point converterTK 1 PF 1 pcs
EEI-Int-RHC-01.12 95
Uponor Radiant Heating/Cooling > Uponor gypsum panel
EEI-Int-RHC-01.1296
Uponor Gypsum Panel is the
ideal system for heating and
cooling. The moderate temper-
ature of the water feeds the
radiant system makes it partic-
ularly suitable to be combined
with condensing boilers, heat
pumps, solar panels and other
alternative sources of energy.
Your advantages
quick and easy to install
for new buildings and renovation
high comfort
fast response time
completely silent (no fan noise).
System components
Uponor Gypsum Panel
Systempipe / -Fittings
Uponor PE-Xa
pipe
9,9 x 1,1
Additional components
Uponor PE-Xa pipe
20x2
Manifold / Cabinets
Uponor compression
Adapter
Uponor PE-Xa Q&E
Coupling
Uponor PE-Xa Q&E tee
reducer 20x9.9x20
Uponor PE-Xa Pipe 9.9x1.1
expander
Uponor PE-Xa Q&E jointing
reducer 20x9.9
Uponor Gypsum Panel
Uponor Gypsum panel
passive
velta P�-�
a
Uponor Radiant Heating/Cooling > Uponor gypsum panel
Uponor gypsum panel
Uponor gypsum panel
Radiant panel for heating and cooling applications. Consisting of a gypsum
board (15mm), Uponor eval PE-Xa pipe 9.9x1.1 mm and 27mm of EPS
200 (30 kg/m³).
Uponor gypsum passive panel has the same layout as the active panels but
consists no pipes.
Sizes: 2000x1200mm, 1000x1200mm, 500x1200mm.
Item no. h [mm] l [mm] w [mm] A [m²] Description unit
1047319 42 2000 1200 2.40Uponor gypsum panel 2000x1200 Type 2
1 pcs
1047320 42 1000 1200 1.20Uponor gypsum panel 1000x1200 Type 2
1 pcs
1047321 42 500 1200 0.60Uponor gypsum panel 500x1200 Type 2
1 pcs
Uponor gypsum panel passive
Uponor gypsum panel passive has the same layout as the active gypsum
panels (item no. 1047319-21) but contains no pipes.
Size: 2000x1200mm
Item no. h [mm] l [mm] w [mm] A [m²] Description unit
1020506 42 2000 1200 2.40Uponor gypsum panel passive 2000x1200
1 pcs
Uponor gypsum panel - accessories
Uponor PE-Xa pipes
PE-Xa pipe with an oxygen diffusion barrier manufactured from peroxide
cross-linked polyethylene (PE-Xa) using the Engel method complying
with e.g. prENISO 15875 “Plastics piping systems for hot and cold water
installations - Cross-linked polyethylene” with an oxygen diffusion barrier
of EVOH (ethyl vinyl alcohol). Uponor pipes fulfil the requirements for
oxygen diffusion resistance as per DIN 4726. Malfunction temperature
95°C. Design pressure 8,8 bar (at 70°C).
Item no. d [mm] s [mm] l [m] V [l/m] Description unit
1009230 20 2.0 240 0.2Uponor pe PE-Xa Q&E pipe 20x2.0240 m coil 240 m
1009231 20 2.0 480 0.2Uponor pe PE-Xa Q&E pipe 20x2.0480 m coil 480 m
Uponor PE-Xa Q&E coupling 9.9
For Uponor PE-Xa pipe 9.9 x 1.1 mm, consisting of:
- 1 coupling
- 2 PEX Q&E rings for secure connection
Material: Coupling made in brass; PEX Q&E rings made in high-pressure
cross-linked polyethylene
Item no. d [mm] s [mm] l [mm] z [mm] Description unit
1005264 9.9 1.1 34 4Uponor PE-Xa Q&E coupling 9.9-9.9with two PEX rings 10 pcs
Uponor PE-Xa conversion nipple
For Uponor PE-Xa pipes 9.9 x 1.1 mm, made of brass.
Item no. d [mm] MT ["] l [mm] z [mm] A/F [mm] Description unit
1005265 9.9 R 1/2 39 14 22Uponor PE-Xa conversion nipple9.9 - 1/2 with one PEX ring 10 pcs
EEI-Int-RHC-01.12 97
Uponor Radiant Heating/Cooling > Uponor gypsum panel
Uponor gypsum panel - accessories
Uponor PE-Xa Q&E jointing reducer 20x9.9
For connection of Uponor PE-Xa pipes, made of brass.
Item no. d [mm] d1 [mm] Description unit
1020518 9.9 20Uponor PE-Xa Q&E jointing reducer 20 x 9.9incl. 1 PEX ring 9.9 and 1 PEX ring 20 5 pcs
Uponor PE-Xa Q&E tee reducer 20x9.9x20
For connection of Uponor PE-Xa pipes, made of brass.
Item no. d [mm] d1 [mm] d2 [mm] Description unit
1020524 20 9.9 20Uponor PE-Xa Q&E tee reducer 20 X 9.9 X 9.9incl. 1 PEX ring 9.9 and 2 PEX rings 20 5 pcs
Uponor Q&E ring natural
Made of PE-X. Uponor Q&E rings natural intended for Uponor Q&E
fittings. For PE-Xa pipe dimensions 16, 20, 25, 32, 40, 50 and 63 mm.
Item no. d [mm] colour [-] p [bar] Description unit
1042836 20 natural 6+10Uponor Q&E ring natural with stop edgeUponor PE-Xa dim 20 mm 20 pcs
Uponor PE-X ring for PE-Xa pipes
For Uponor Minitec PE-Xa pipe 9.9 x 1.1 mm; to secure fixing to Minitec
fittings
Material: High-pressure cross-linked polyethylene (PE-Xa)
Item no. d [mm] Description unit
1005263 9.9Uponor PE-X ring for PE-Xa pipes9.9 x 1.1 10 pcs
EEI-Int-RHC-01.1298
Uponor Radiant Heating/Cooling > Uponor tools
Uponor tools
Uponor pipe cutter up to 25 mm
For Uponor pipes, outside diameter up to 25 mm.
Item no. d [mm] Description unit
1001369 - 25Uponor pipe cutter for PEX14-25mm 1 pcs
Uponor pipe cutter up to 20
For Uponor pipes, outside diameter up to 20 mm with corrugated pipe
cutting device.
Item no. d [mm] Description unit
1006636 - 20Uponor pipe cutter 14-20 mm
1 pcs
1006637Uponor spare bladefor pipe cutter 1006636 1 pcs
Uponor cutting aid
For the easy cutting of Uponor pipe fixing system panels.
Item no. Description unit
1016724Uponor cutting tool for pipe positioning panel 14-16mmwith insulation 1 pcs
Uponor polystyrene cutter tool for lightweight system
For cutting of individual pipe curves and guides. And also for the smooth
cutting to size of polystyrene items. 230 V connection.
Item no. OV [V] Description unit
1006290 230Uponor polystyrene cutting toolfor lightweight system 1 pcs
Uponor outside bending spring MLC
Special bending spring for Uponor MLC pipe.
Item no. d [mm] Description unit
1006639 14Uponor bending spring outside MLC 14
1 pcs
1006640 16Uponor bending spring outside MLC 16
1 pcs
EEI-Int-RHC-01.12 99
Uponor Radiant Heating/Cooling > Uponor tools
Uponor tools
Uponor manual pressing tool MLC
For pressing of Uponor press fittings MLC 14-20 mm in conjunction with
exchangeable inserts. Supplied in case without exchangeable inserts.
Item no. d [mm] Description unit
1015764 14-20Uponor manual press tool MLC 14-20incl. case without pressing inserts 1 pcs
Uponor manual pressing tool inserts MLC
For inserting into the manual pressing tool for pressing the Uponor press
fittings MLCP 14/16/18/20 mm.
Item no. d [mm] Description unit
1015776 14Uponor manual press tool insert MLC 14
1 set
1015777 16Uponor manual press tool insert MLC 16
1 set
1015780 20Uponor manual press tool insert MLC 20
1 set
Uponor press tool electric UP 75
Supplied in plastic case for the 230 V mains connection, without pressing
jaws. Range of application up to 110 mm.
Technical Specifications:
Weight of the pressing tool: 3.30 kg
Nominal voltage: 230 V DC / 50 Hz
Nominal capacity: 200 Watt
For dimensions: up to 110 mm
Press power: ca. 32 kN
Press duration: ca. 7 sec.
Item no. d [mm] OV [V] Description unit
1007082 - 110 230Uponor electric pressing tool UP 75 ELwithout pressing jaws 1 pcs
Uponor PE-Xa pipe 9.9x1.1 expander
Hand tool for the easy expansion of Uponor PE-Xa pipes 9.9 x 1.1 mm,
consisting of:
- 1 hand expander
- 1 expander head for PE-Xa pipe 9.9 x 1.1 mm
- 1 tube of lubricant
- 1 case
Item no. Description unit
1006247Uponor PE-Xa pipe 9.9 x 1.1 expandertool 1 set
EEI-Int-RHC-01.12100
Uponor Radiant Heating/Cooling > Uponor tools
Uponor tools
Uponor Q&E battery tool M12
Battery powered expander tool for 6 bar pipes up to dimension 32mm and
for 10 bar pipes up to 28 mm.
Auto-rotating with M12 expander heads.
< 10seconds full expansion onto a joint
< 2.2kg with head and battery
Steel gear and integrated metal frame
LED work light, fuel gauge, Tool free head change
incl. 2 Li-ion 1.5 Ah batteries, charger 220-240V/50-60Hz and grease
(Mo)
Item no. Description unit
1057166Uponor Q&E M12 expanderwith 6 bar heads 16-20-25 1 set
Uponor Q&E battery tool M18
Battery powered expander tool for 6 bar pipes up to dimension 40mm and
for 10 bar pipes up to 32 mm.
Auto-rotating with M18 expander heads.
< 10seconds full expansion onto a joint.
< 2.2kg with head and battery
Steel gear and integrated metal frame
LED work light, fuel gauge, Tool free head change
incl. 2 Li-ion 1.5 Ah batteries, charger 220-240V/50-60Hz and grease
(Mo)
Item no. Description unit
1057169Uponor Q&E M18 expanderwith 6 bar heads H20-H25-H32 1 set
Uponor Q&E M12 expander heads
Q&E head for NKB fittings, for M12 and M18 tools.
Expander head packed screw pack
Item no. d [mm] stroke [mm] p [bar] Description unit
1057184 15 14 10Uponor Q&E M12 expander head14/15x2.5 mm 1 pcs
1057185 18 14 10Uponor Q&E M12 expander head17/18x2.5 mm 1 pcs
Uponor Q&E M12 expander heads
Q&E head for S5 fittings, for M12 and M18 tools.
Expander head packed screw pack
Item no. d [mm] stroke [mm] p [bar] Description unit
1057172 16 14 6+10Uponor Q&E M12 expander head16x1.8/2.0/2.2 mm 1 pcs
1057173 20 14 6Uponor Q&E M12 expander head20x1.9/2.0 mm 1 pcs
1057175 25 14 6Uponor Q&E M12 expander head25x2.3 mm 1 pcs
EEI-Int-RHC-01.12 101
stroke [mm] p [bar]
14 6
stroke [mm] p [bar]
25 6
Uponor Radiant Heating/Cooling > Uponor tools
Uponor tools
Uponor Q&E M18 expander heads
Q&E head for S5 fittings, for M18 tools.
Expander head packed screw pack
Item no. d [mm] stroke [mm] p [bar] Description unit
1057178 20 25 6Uponor Q&E M18 expander headH20x1.9/2.0 mm 1 pcs
1057180 25 25 6Uponor Q&E M18 expander headH25x2.3 mm 1 pcs
1057183 40 25 6Uponor Q&E M18 expander headH40x3.7 mm 1 pcs
Uponor Q&E M12 battery
Q&E M12 rechargeable Li-ion battery for M12 tool.
Battery 1.5 AH
Item no. Description unit
1057409Uponor Q&E battery M121.5 AH 1 pcs
Uponor Q&E M12 charger
Q&E M12 charger for M12 tool
Charger 220-240V / 50-60Hz
Item no. OV [V] Description unit
1057410 230Uponor Q&E charger M12220-240V 1 pcs
Uponor Clip Stapler
High-precision, wear-proof tool for pinning with staples in magazines, with
curved magazine.
Item no. Description unit
1002295Uponor Clip stapler
1 pcs
EEI-Int-RHC-01.12102
Uponor Radiant Heating/Cooling > Uponor tools
Uponor tools
Uponor manual roller
For sticking down of insulation sections and edges, takes a roll of tape.
Item no. Description unit
1000142Uponor manual roller
1 pcs
Uponor Q&E head graphite paste
Colloidal graphite paste. For Uponor Q&E Tools.
Item no. Description unit
1008334Uponor graphite paste for Uponor plierscolloidal graphite paste, 30 g/tube 20 pcs
Uponor Twisting tool
For twisting of the tying wires while fixing the pipe on steel meshes.
Item no. Description unit
1006243Twisting tool for tying wire
1 pcs
Uponor cutter knife
Cutter knife for polystyrene insulation.
Item no. Description unit
1006263Uponor polystyrene cutter knife
1 pcs
Uponor ring spanner wrench
For swivel nut of the Uponor compression adapters
Item no. A/F [mm] Description unit
1006265 30Uponor ring spanner wrenchfor wrench size 30 mm 1 pcs
Uponor door pipe duct
Expansion rod with pipe laying mount
Item no. Description unit
1007179Uponor door pipe guide
1 pcs
EEI-Int-RHC-01.12 103
Uponor Radiant Heating/Cooling > Uponor tools
Uponor tools
Uponor plastic manifold valve tool
For mounting and de-mounting the valves of the plastic manifold.
Item no. Description
1009216Uponor plastic manifold valve tool
1 pcs
Uponor Tying tool
Item no. Description
1034533Twisting tool for tying wire
1 pcs
Uponor pipe uncoiler with pipe guide
For laying of all Uponor pipes up to dimension 25 mm. Suits different pipe
coils with 300 mm and 600 mm internal diameter.
Item no. Description unit
1035807Uponor pipe uncoiler with pipe guide
1 pcs
Uponor snow and ice decoiler
Uponor snow and ice melting, pipe decoiler.
Item no. Description unit
1033691Uponor Meltaway decoilerfor 25 x 2,3 mm pipe 1 pcs
EEI-Int-RHC-01.12104
International sales and delivery terms
Uponor Radiant Heating/Cooling > International sales and delivery terms
1 Interpretation
2 Basis of the sale
3 Orders and specifications
4 Price of Goods
5 Terms of payment
6 Delivery and Performance
EEI-Int-RHC-01.12 105
International sales and delivery terms
Uponor Radiant Heating/Cooling > International sales and delivery terms
7 Risk and property
8 Liability
9 Insolvency of Buyer
10 Packing
11 General
EEI-Int-RHC-01.12106
Uponor Radiant Heating/Cooling > Item search register
Item search register
Item no. unit Page
1000002 m² 23
1000003 m² 23
1000012 pcs 20
1000015 m² 23
1000016 pcs 40
1000017 m² 23, 33
1000018 m 24
1000019 pcs 24
1000079 m 39
1000080 m 39
1000081 m 39
1000082 pcs 39
1000083 pcs 40
1000084 l 40
1000085 l 41
1000138 pcs 59
1000142 pcs 103
1000296 pcs 91
1000297 pcs 92
1000298 pcs 92
1000299 pcs 92
1000300 pcs 92
1000301 pcs 92
1000303 pcs 92
1000304 pcs 92
1000310 pcs 93
1000311 pcs 94
1000312 pcs 95
1000313 pcs 95
1000314 pcs 95
1000502 pcs 52
1000503 pcs 52
1000504 pcs 52
1000505 pcs 52
1000515 pcs 54
1000516 pcs 66
1000517 pcs 66
1000518 pcs 54
1000527 pcs 53
1000529 pcs 54
1000531 pcs 56
1000533 pcs 56
1000535 pcs 57
1000536 pcs 57
1000537 pcs 59
1000538 pcs 53
1000539 pcs 57
1001369 pcs 99
1002295 pcs 102
1002296 pcs 23
1002297 pcs 23
1002356 pcs 66
1002357 pcs 66
1005049 m² 12, 33, 40
1005066 l 41
Item no. unit Page
1005084 m² 33
1005087 m² 33
1005100 set 46
1005168 pcs 47
1005170 pcs 47
1005261 m² 9
1005263 pcs 9, 37, 98
1005264 pcs 9, 36, 97
1005265 pcs 9, 37, 97
1005266 pcs 46
1005267 m 10
1005268 m 10
1005269 pcs 10, 40
1005274 m 10, 36
1005284 pcs 85
1005286 pcs 85
1005287 pcs 33, 74, 81
1005289 pcs 74
1005290 m 73, 81
1005291 pcs 73, 81
1005295 pcs 72, 82
1005296 pcs 72, 82
1005297 pcs 72, 82
1005298 pcs 72, 82
1005358 m 73
1005372 pcs 74, 81
1005477 m² 15
1005478 m² 15
1005479 m 15
1005480 m 15
1005481 m 16
1005482 pcs 16
1005483 m 16
1005484 m 16
1005485 m² 12
1005486 pcs 12
1005498 m 24
1005576 pcs 68
1005605 pcs 61
1005675 set 68
1006243 pcs 103
1006247 set 100
1006263 pcs 103
1006265 pcs 103
1006290 pcs 99
1006636 pcs 99
1006637 pcs 99
1006639 pcs 99
1006640 pcs 99
1006641 pcs 46
1007082 pcs 100
1007179 pcs 103
1007226 m² 20
1007228 m² 20
1007232 m² 20
Item no. unit Page
1007234 m² 20
1008334 pcs 103
1008671 pcs 72, 84
1008673 pcs 86
1008683 pcs 86
1008932 pcs 72
1008939 m 86
1009004 pcs 48
1009006 pcs 74, 82, 87
1009129 pcs 38
1009132 pcs 38
1009209 set 44
1009214 set 44
1009215 set 44
1009216 pcs 104
1009217 pcs 44
1009222 pcs 33, 74, 82
1009226 m 17, 25, 34
1009227 m 17, 25, 34
1009228 m 25, 34, 36
1009230 m 25,34,36,72,97
1009231 m 25,34,36,72,97
1009233 pcs 48, 74
1012869 m 74, 82, 87
1013005 pcs 60
1013006 pcs 61
1013008 pcs 59
1013051 pcs 45
1013052 pcs 45
1013053 pcs 45
1013054 pcs 45
1013055 pcs 45
1013056 pcs 45
1013057 pcs 45
1013058 pcs 45
1013059 pcs 45
1013060 pcs 45
1013061 pcs 45
1013062 pcs 45
1013063 pcs 45
1013064 pcs 45
1013065 pcs 45
1013066 pcs 45
1013067 pcs 45
1013068 pcs 45
1013069 pcs 45
1013070 pcs 45
1013071 pcs 45
1013072 pcs 45
1013127 m 24
1013366 m 13, 18, 26, 31
1013371 m 18, 26, 31
1013378 m 18, 26, 31
1013380 m 18, 26, 31
1013392 m 26
EEI-Int-RHC-01.12 107
Uponor Radiant Heating/Cooling > Item search register
Item search register
Item no. unit Page
1014122 pcs 47
1015154 pcs 13, 18, 26, 31
1015164 pcs 18, 21, 26, 31
1015187 pcs 26
1015764 pcs 100
1015776 set 100
1015777 set 100
1015780 set 100
1016699 m² 28
1016700 m² 29
1016701 m² 29
1016702 m² 30
1016703 m² 28
1016724 pcs 99
1020506 pcs 97
1020518 pcs 37, 98
1020524 pcs 37, 98
1022341 m 78
1022983 pcs 90
1022984 pcs 90
1022985 pcs 93
1022986 pcs 93
1022987 pcs 91
1022988 pcs 93
1023006 pcs 73
1023007 pcs 73, 84
1023008 pcs 73, 84
1023011 pcs 73
1023012 pcs 73, 84
1023013 pcs 73, 84
1023448 m 72, 84
1030134 pcs 76
1030135 set 76
1030580 pcs 43
1030581 pcs 43
1030582 pcs 43
1030583 pcs 43
1030584 pcs 43
1030585 pcs 43
1032701 set 46
1032702 set 44
1033024 m 9, 36
1033025 m 9, 36
1033026 m 9, 36
1033625 m 78
1033626 m 78
1033628 m 79
1033629 m 79
1033630 m 79
1033631 pcs 78
1033632 pcs 78
1033633 pcs 78
1033634 pcs 79
1033635 pcs 79
1033636 pcs 79
Item no. unit Page
1033637 pcs 78
1033638 pcs 78
1033639 pcs 78
1033640 pcs 78
1033641 pcs 78
1033642 pcs 78
1033643 pcs 78
1033644 pcs 79
1033645 pcs 78
1033646 pcs 79
1033647 pcs 78
1033648 pcs 79
1033649 pcs 79
1033650 pcs 79
1033652 pcs 80
1033653 pcs 80
1033654 pcs 80
1033657 pcs 80
1033659 pcs 80
1033660 pcs 80
1033661 pcs 80
1033662 pcs 80
1033663 pcs 80
1033666 pcs 81
1033667 pcs 81
1033668 pcs 81
1033672 pcs 79
1033673 pcs 81
1033675 pcs 81
1033676 pcs 81
1033678 pcs 79
1033689 pcs 82
1033691 pcs 104
1033975 pcs 48
1034533 pcs 104
1034535 m 17, 25, 34
1035807 pcs 104
1042389 pcs 18, 21, 26, 31
1042420 set 43
1042471 set 43
1042836 pcs 79, 98
1042837 pcs 26, 34, 37
1042840 pcs 73, 84
1042942 pcs 93
1042943 pcs 93
1042944 pcs 93
1042945 pcs 93
1042946 pcs 94
1042947 pcs 94
1044181 pcs 33
1044809 pcs 93
1044810 pcs 93
1044811 pcs 93
1044812 pcs 93
1045315 pcs 89
Item no. unit Page
1045316 pcs 89
1045317 pcs 89
1045318 pcs 89
1045319 pcs 90
1045320 pcs 90
1045323 pcs 90
1045324 pcs 90
1045325 pcs 91
1045326 pcs 91
1045327 m 91
1045328 pcs 91
1045464 pcs 86
1045562 set 51
1045565 pcs 51
1045568 pcs 52
1045570 pcs 53
1045571 pcs 54
1045572 pcs 53
1045813 set 75
1045814 set 75
1045815 set 75
1045816 set 76
1046114 pcs 52
1046115 pcs 52
1046747 set 85
1046748 set 85
1046749 set 85
1046870 pcs 68
1046991 pcs 48
1046992 pcs 48
1046993 pcs 48
1046994 pcs 48
1046996 pcs 49
1046997 pcs 49
1046998 pcs 49
1046999 pcs 49
1047000 pcs 48
1047319 pcs 97
1047320 pcs 97
1047321 pcs 97
1047610 m 17, 25, 30
1047611 m 17, 25, 30
1047612 m 17, 25, 30
1047615 m 72, 84
1047618 m 72, 84
1047624 m 21
1047625 m 21
1047844 pcs 64
1047845 pcs 65
1047846 pcs 65
1047847 pcs 66
1047848 pcs 66
1047867 pcs 86
1048010 pcs 56
1048011 pcs 58
EEI-Int-RHC-01.12108
Uponor Radiant Heating/Cooling > Item search register
Item search register
Item no. unit Page
1048012 pcs 58
1048013 pcs 59
1048249 m 21
1048290 m 12, 17, 25, 30
1048291 m 12, 17, 25, 30
1048395 m 21
1048684 pcs 92
1048685 pcs 92
1048763 pcs 66
1048780 pcs 69
1048781 pcs 69
1048782 pcs 70
1048783 pcs 70
1052123 pcs 80
1056656 pcs 80
1057166 set 101
1057169 set 101
1057172 pcs 101
1057173 pcs 101
1057175 pcs 101
1057178 pcs 102
1057180 pcs 102
1057183 pcs 102
1057184 pcs 101
1057185 pcs 101
1057368 pcs 47
1057370 pcs 47
1057409 pcs 102
1057410 pcs 102
1057441 pcs 47
1057442 pcs 47
1058089 pcs 47
1058090 pcs 47
1058091 pcs 47
1058092 pcs 47
1058422 pcs 60
1058423 pcs 60
1058424 pcs 61
1058425 pcs 61
1058426 pcs 60
1058427 pcs 60
1058428 pcs 13, 18, 26, 31
1058429 pcs 18, 26, 34
1058659 pcs 13, 18, 26, 31
1058660 pcs 18, 21, 26, 31
1058661 pcs 18, 26, 34
1058668 pcs 26, 34
EEI-Int-RHC-01.12 109
EEI-Int-RHC-01.12110
Notes
How to contact us
EEI-Int-RHC-01.12 111
Customer Service Center T + 49 (0)9521-690-370
F + 49 (0)9521-690-750
Technical assistance T +49 (0)9521-690-739 or 834
F +49 (0)9521-690-750
Export Department T +49 (0)9521-690-370
F +49 (0)9521-690-750
We reserve the right to make technical amendments and carry out updates.
Uponor – partnering with professionals
Uponor is a leading supplier of plumbing and heating systems for the
residential and commercial building markets across Europe and North
America, and a market leader in municipal infrastructure pipe systems in
the Nordic countries. Uponor's key applications include indoor climate
and plumbing systems.
Uponor International Sales takes care of all business activities in the
Balkans, Western, Central and East Asia, Africa and Latin America.
Uponor. Simply more.
01/
20
12
– S
ub
ject
to
mo
difi c
ati
on
s
Uponor GmbH
P.O. Box 1641
97433 Hassfurt
Germany
T +49-(0)9521 690 0
F +49-(0)9521 690 750
W www.uponor.com/international