us navy plan black the great war at sea i & ii us navy plan black · 2013-12-12 · amc01...

AMC01 Lusitania 30 - - 2 AMC02 Mauretania 30 - - 2 AMC03 Aquitania 35 - - 1 AMC04 Carmania 12 - - 1s AMC05 Caronia 12 - - 1s AMC06 Olympic 35 - - 1 AMC07 Britannic 35 - - 1 AMC08 Laurentic 12 - - 1s AMC09 Otranto 8 - - 1s AMC10 Macedonia 8 - - 1s AMC11 Moldavia 8 - - 1s AMC12 Marmora 8 - - 1s AMC13 Mongolia 8 - - 1s AMC14 India 8 - - 1s Name primary secondary tertiary torp. move hull fuel AMC01 Prinz Eitel Friedrich 15 - - - 1s AMC02 Kaiser Wilhelm der Grosse 20 - - - 1 AMC03 Konprinz Wilhelm 20 - - - 1 AMC04 Cap Trafalgar 12 - - - 1 AMC05 Berlin 12 - - - 1s AMC06 Imperator 30 - - - 1 AMC07 Vaterland 30 - - - 1 Name primary secondary tertiary torp. move hull fuel v1.0 24 October, 1999 The bulk of the variant counters contained in this file are intended as replacements for the 1/2-inch counters provided in US Navy Plan Black. The remainder are for use with The Great War at Sea I & II, and the GWaS system at large. The Russian and Italian units are updates of earlier variant counters with more accurate deck plans. Also included are a number of German and British armed merchant cruisers that can be used in place of the more generic counters included in Avalanche Press Ltd.’s US Navy Plan Black. These are all examples of liners that either were actually armed as auxiliary cruisers, or which would likely have been armed, had circumstances been slightly different. To assemble, first mount front side of the counter sheet to a sheet of mat or chip board using a permanent spray adhesive. With a very sharp X-acto knife and a metal straight edge, trim the mounted counter sheet along any two adjoining edges using the marks at each corner at guides. Do the same for the corresponding two edges of the as yet unmounted back side (remember that the back side sheet is a mirror image of the front). Next mount the back sheet to the cardboard, aligning the freshly trimmed edges of the paper and cardboard together. The counter images on the front and back sides should now match up nicely. Last, trim the counters from the cardboard, two rows at a time. Leave the “dividing” areas between the double counter rows intact if possible, to prevent the counters from shifting while they are cut.

Upload: others

Post on 12-Apr-2020

0 views

Category:

Documents

0 download

Report

Download

Embed Size (px):

TRANSCRIPT

Page 1: US Navy Plan Black The Great War at Sea I & II US Navy Plan Black · 2013-12-12 · AMC01 Lusitania 30 - - 2 AMC02 Mauretania 30 - - 2 AMC03 Aquitania 35 - - 1 AMC04 Carmania 12 -

Name primary secondary tertiary torp. move hull fuel

AMC01 Prinz Eitel Friedrich 15 - - - 1sAMC02 Kaiser Wilhelm der Grosse 20 - - - 1AMC03 Konprinz Wilhelm 20 - - - 1AMC04 Cap Trafalgar 12 - - - 1AMC05 Berlin 12 - - - 1sAMC06 Imperator 30 - - - 1AMC07 Vaterland 30 - - - 1

Name primary secondary tertiary torp. move hull fuel

v1.0 24 October, 1999

The bulk of the variant counters contained in this file are intended as replacements for the 1/2-inch countersprovided in US Navy Plan Black. The remainder are for use with The Great War at Sea I & II, and the GWaSsystem at large. The Russian and Italian units are updates of earlier variant counters with more accurate deckplans. Also included are a number of German and British armed merchant cruisers that can be used in placeof the more generic counters included in Avalanche Press Ltd.’s US Navy Plan Black. These are all examplesof liners that either were actually armed as auxiliary cruisers, or which would likely have been armed, hadcircumstances been slightly different.

To assemble, first mount front side of the counter sheet to a sheet of mat or chip board using a permanentspray adhesive. With a very sharp X-acto knife and a metal straight edge, trim the mounted counter sheetalong any two adjoining edges using the marks at each corner at guides. Do the same for the correspondingtwo edges of the as yet unmounted back side (remember that the back side sheet is a mirror image of thefront). Next mount the back sheet to the cardboard, aligning the freshly trimmed edges of the paper andcardboard together. The counter images on the front and back sides should now match up nicely. Last, trimthe counters from the cardboard, two rows at a time. Leave the “dividing” areas between the double counterrows intact if possible, to prevent the counters from shifting while they are cut.