user manual artigo a630 - docid81hrs3j1.cloudfront.net · iv artigo a630 user manual bo contents 1...

USER MANUAL

ARTiGO A630 Cost Efficient ARM based

Fanless system

1.00-10022017-1728

Copyright

Copyright ©2017 VIA Technologies Incorporated. All rights reserved.

No part of this document may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language, in any form or by any means, electronic, mechanical, magnetic, optical, chemical, manual or otherwise without the prior written permission of VIA Technologies, Incorporated.

Trademarks

All trademarks are the property of their respective holders.

Disclaimer

No license is granted, implied or otherwise, under any patent or patent rights of VIA Technologies. VIA Technologies makes no warranties, implied or otherwise, in regard to this document and to the products described in this document. The information provided in this document is believed to be accurate and reliable as of the publication date of this document. However, VIA Technologies assumes no responsibility for the use or misuse of the information (including use or connection of extra device/equipment/add-on card) in this document and for any patent infringements that may arise from the use of this document. The information and product specifications within this document are subject to change at any time, without notice and without obligation to notify any person of such change.

VIA Technologies, Inc. reserves the right the make changes to the products described in this manual at any time without prior notice.

Regulatory Compliance

FCC-A Radio Frequency Interference Statement

This equipment has been tested and found to comply with the limits for a class A digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference, in which case the user will be required to correct the interference at his personal expense.

Notice 1

The changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

Notice 2

Shielded interface cables and A.C. power cord, if any, must be used in order to comply with the emission limits.

Notice 3

The product described in this document is designed for general use, VIA Technologies assumes no responsibility for the conflicts or damages arising from incompatibility of the product. Check compatibility issue with your local sales representatives before placing an order.

Battery Recycling and Disposal• Only use the appropriate battery specified for this product. • Do not re-use, recharge, or reheat an old battery. • Do not attempt to force open the battery.• Do not discard used batteries with regular trash.• Discard used batteries according to local regulations.

Safety Precautions• Always read the safety instructions carefully.• Keep this User’s Manual for future reference.• All cautions and warnings on the equipment should be noted.• Keep this equipment away from humidity.• Lay this equipment on a reliable flat surface before setting it up.• Make sure the voltage of the power source and adjust properly 110/220V before connecting the equipment to the power inlet.• Place the power cord in such away that people cannot step on it. • Always unplug the power cord before inserting any add-on card or module.• If any of the following situations arises, get the equipment checked by authorized service personnel: • The power cord or plug is damaged. • Liquid has penetrated into the equipment. • The equipment has been exposed to moisture. • The equipment has not worked well or you cannot get it work according to User’s Manual. • The equipment has dropped and damaged. • The equipment has obvious sign of breakage.• Do not leave this equipment in an environment unconditioned or in a storage temperature above 60°C (140°F). The equipment may be damaged.• Do not leave this equipment in direct sunlight.• Never pour any liquid into the opening. Liquid can cause damage or electrical shock.• Do not place anything over the power cord.• Do not cover the ventilation holes. The openings on the enclosure protect the equipment from overheating

ARTiGO A630 User Manual

Box Contents

• 1 x ARTiGO A630 system• 1 x AC-to-DC adapter• 1 x Power cord• 1 x Screw pack for miniPCIe module • 4 x Rubber feet pack

Ordering Information

Part Number Description

ATG-A630-1D10A1 Fanless embedded system with 1.0GHz VIA Cortex-A9 SoC, 1GB DDR3 RAM, 4GB eMMC, 2 x USB 2.0, 1 x Micro USB 2.0 OTG, 1 x HDMI, 1 x COM, 1 x DIO , 1 x 10/100Mpbs Ethernet, 1 x miniPCIe slot, 1 x Micro SD slot and 12V DC-in

Optional Accessories

Wireless Accessories

Part Number Description

EMIO-5531-00A1 VAB-820-W IEEE 802.11b/g/n USB Wi-Fi & Bluetooth module with assembly kit and antenna

EMIO-2531-00A1 VAB-820-W-M IEEE 802.11b/g/n miniPCIe Wi-Fi & Bluetooth module with assembly kit and antenna

EMIO-2550-01A1 3.75G HSPA/UMTS mobile broadband full size miniPCIe module with assembly kit and antenna.

iv


Table of Content

1. Product Overview .............................................................................................................. 11.1 Key Features ......................................................................................................................................... 1

1.1.1 ARM Based System ........................................................................................................................ 11.1.2 OptimizedIntegrationwithMultipleI/OAccess ........................................................................... 11.1.3 NetworkingSupport ...................................................................................................................... 11.1.4 EmbeddedOperatingSystemReady .............................................................................................. 11.1.5 StorageExpansion .......................................................................................................................... 1

1.2 ProductSpecifications ......................................................................................................................... 21.3 LayoutDiagram .................................................................................................................................... 51.4 Dimensions .......................................................................................................................................... 6

2. ExternalI/OPinDescriptionsandFunctionality ................................................................ 72.1 HDMI® Port ........................................................................................................................................... 72.2 USB 2.0 Port ......................................................................................................................................... 72.3 Micro USB 2.0 OTG Port ....................................................................................................................... 82.4 DIOPort ................................................................................................................................................ 82.5 10/100MbpsEthernetPort ................................................................................................................. 92.6 Audio Jack ........................................................................................................................................... 102.7 Micro SD Card Slot .............................................................................................................................. 102.8 PowerOn/OffButton .......................................................................................................................... 112.9 DC-InJack ........................................................................................................................................... 112.10 Power LED .......................................................................................................................................... 12

3. Onboard Connector ......................................................................................................... 133.1 USB 2.0 Connector ............................................................................................................................. 133.2 MiniPCIeSlot ...................................................................................................................................... 143.3 SIMCardSlot ...................................................................................................................................... 153.4 UART Connector ................................................................................................................................ 15

4. HardwareInstallation ...................................................................................................... 164.1 OpeningtheChassis .......................................................................................................................... 164.2 InstallingtheRubberfeet ................................................................................................................... 18

5. SoftwareandTechnicalSupport ...................................................................................... 195.1 Android Support ................................................................................................................................. 195.2 LinuxSupport ..................................................................................................................................... 195.3 TechnicalSupportsandAssistance ..................................................................................................... 19

AppendixA.InstallingWirelessAccessories ............................................................................ 20A.1. InstallingtheEMIO-5531USBWi-Fi&Bluetoothmodule ................................................................. 20A.2. InstallingtheEMIO-2531miniPCIeWi-Fimodule&Bluetoothmodule ............................................. 23A.3. InstallingtheEMIO-2550miniPCIeMobileBroadbandmodule ......................................................... 26

v


ListofFiguresFigure1: FrontpanelI/Olayout .......................................................................................................................... 5Figure2: BackpanelI/Olayout........................................................................................................................... 5Figure3: DimensionsofARTiGOA630(Frontview) ............................................................................................ 6Figure4: DimensionsofARTiGOA630(Rightview) ............................................................................................ 6Figure5: HDMIportdiagram .............................................................................................................................. 7Figure6: USB2.0portdiagram ........................................................................................................................... 7Figure7: MicroUSB2.0OTGportdiagram ......................................................................................................... 8Figure8: DIOportdiagram ................................................................................................................................. 8Figure9: 10/100MbpsEthernetportdiagram .................................................................................................... 9Figure10: Audiojacksdiagram ........................................................................................................................... 10Figure11: MicroSDcardslotdiagram ................................................................................................................ 10Figure12: Poweron/offbuttondiagram ............................................................................................................ 11Figure13: DC-injackdiagram ............................................................................................................................. 11Figure14: DC-injackspecificationdiagram ........................................................................................................ 11Figure15: PowerLEDdiagram ............................................................................................................................ 12Figure16: USB2.0connectordiagram ................................................................................................................ 13Figure17: MiniPCIeslotdiagram ........................................................................................................................ 14Figure18: SIMcardslotdiagram ........................................................................................................................ 15Figure19: UARTconnectordiagram ................................................................................................................... 15Figure20: Unscrewingthetopcover ................................................................................................................... 16Figure21: Removingthetopcover ..................................................................................................................... 17Figure22: Installingrubberfeet ......................................................................................................................... 18Figure23: InstallingtheEMIO-5531module ...................................................................................................... 20Figure24: ConnectingtheUSBWi-Ficableandremovingantennaholecover .................................................. 21Figure25: InstallingantennaandantennacableofEMIO-5531module ............................................................ 21Figure26: Connectingtheantennacabletothemicro-RFconnectoronEMIO-5531module ........................... 22Figure27: InsertingEMIO-2531module ............................................................................................................. 23Figure28: SecuringtheEMIO-2531moduleandremovingtheantennacover .................................................. 24Figure29: InstallingantennaandantennacableofEMIO-2531module ............................................................ 24Figure30: Connectingtheantennacabletothemicro-RFconnectoronEMIO-2531 ......................................... 25Figure31: InstallingtheSIMcard ........................................................................................................................ 26Figure32: InsertingEMIO-2550module ............................................................................................................. 27Figure33: SecuringtheEMIO-2550moduleandremovingantennaholecover ................................................. 27Figure34: InstallingantennaandantennacableofEMIO-2550module ............................................................ 28Figure35: Connectingtheantennacabletothemicro-RFconnectoronEMIO-2550module ........................... 28

vi


List of TablesTable1: HDMIportpinouts ................................................................................................................................ 7Table2: USB2.0portpinouts ............................................................................................................................ 7Table3: MicroUSB2.0OTGportpinouts .......................................................................................................... 8Table4: DIOportpinouts ................................................................................................................................... 8Table5: 10/100MbpsEthernetportpinouts .................................................................................................... 9Table6: 10/100MbpsEthernetportLEDcolordefinitions ................................................................................ 9Table7: MicroSDcardslotpinouts .................................................................................................................. 10Table8: Powerbuttonbehaviordescriptions .................................................................................................. 11Table9: DC-injackpinouts .............................................................................................................................. 11Table10: DC-injackspecifications ..................................................................................................................... 11Table11: USB2.0connectorpinouts ................................................................................................................. 13Table12: MiniPCIeslotpinouts.......................................................................................................................... 14Table13: SIMcardslotpinouts .......................................................................................................................... 15Table14: UARTconnectorpinouts ..................................................................................................................... 15

vii


1

1. Product OverviewTheVIAARTiGOA630isanultra-compactandultra-slimfanlessembeddedsystemmeasuring154.40mm(H)x27mm(H)x106.68mm(D)thatprovidesaflexibleplatformwithI/Oconnectivityoptions,networkfeatures,andadvancedsoftwaredevelopmenttoolsforawiderangeofinteractivekiosks,signage,HMI,M2MapplicationsandotheradvancedIoT.

TheARTiGOA630systemisbasedontheVAB-630SBCmainboard,poweredby1.0GHzWM8880Cortex–A9dual-coreprocessorandcompletelycompatiblewithAndroidandLinuxoperatingsystem.TheARTiGOA630comeswithahighperformance3D/2DgraphicsandvideoenginethatsupportsOpenGL®ES2.0hardwareaccelerationforconditionalsupportMPEG-2andH.264videodecoding.

TheARTIGOA630systemfeaturesanimpressiveselectionofdualcoastlineI/OinacompactformfactorincludingoneHDMI®port,twoUSB2.0ports,oneMicroUSB2.0OTGport,oneCOM(TX/RX),one10/100MbpsEthernetport,oneMicroSDcardslot,audiojacksforLine-outandMic-in,12VDC-inandfourantennaholes.Inaddition,theARTiGOA630onboardI/OfeaturesincludeaUARTconnector,SIMcardslot,miniPCIeslotandUSB2.0connectorforaddingtheoptionalVIAEMIOmodulesforminiPCIe/USBWi-Fi&Bluetoothand3Gconnectivity.

1.1 Key Features

1.1.1 ARM Based SystemTheARMbasedARTiGOA630systemispoweredby1.0GHzWM8880Cortex–A9dual-coreprocessorthatprovidesafullrangeofrichfeaturesincludingsuperbmulti-taskingperformance.

1.1.2 OptimizedIntegrationwithMultipleI/OAccessWithfrontandbackpanelI/Oaccess,theVIAARTiGOA630canbeeasilyconfiguredtosupportawidevarietyofapplicationswitheasyintegrationandquicksetup.Itcomeswithanultra-slimandultra-compactchassisdesigntobeinstalledincriticalenvironmentsandtoensuremaximumreliability.

1.1.3 NetworkingSupportTheARTiGO-A630isequippedwithRJ-45portthatsupports10/100MbpsEthernet.WirelessconnectivitycanbeaddedthroughtheoptionalVIAEMIOmodulessuchasminiPCIe/USBWi-Fi&Bluetoothmoduleand3Gnetwork.

1.1.4 EmbeddedOperatingSystemReadyTheARTiGOA630featuresacompletesignagesoftwareevaluationimagefeaturingAndroid5.0LinuxKernel3.4.5aswellastheVIASmartETKincludingGPIO,UARTandWatchdogtimeraccess.

1.1.5 StorageExpansionTheARTiGOA630hasanonboard4GBeMMCflashstorageandaMicroSDcardslotforamaximumexpandablestorageofupto32GB.


2

1.2 ProductSpecifications

Processor

• 1.0GHzVIACortex-A9dual-coreSoC

System Memory

• 1GB DDR3 SDRAM onboard

Storage

• 4GBeMMCFlashmemory• Micro SD Card

Boot Loader

• 512KBSPIFlashROM

Graphics

• Support Mali-400 SP GPU• Twoindependent,integrated3D/2Dandvideographicprocessingunits.• GraphicsenginesupportingOpenGL®ES2.0hardwareacceleration• SupportsMPEG-2andH.264videodecodingupto1080p

LAN

• ASICAX88772CLF

Audio

• VIAVT1603AI2CAudioCodec

HDMI

• IntegratedHDMI1.4transmitter

USB

• ASICUSB2514B-AEZCUSB2.0hi-speed4-porthubcontroller

Expansion I/O

• 1xminiPCleslot(foroptionalminiPCIeWi-Fi&Bluetoothand3Gmodule)• 1xUSB2.0connector(foroptionalUSBWi-Fi&Bluetoothmodule)


3

Front Panel I/O

• 1xMicroUSB2.0OTGport• 1xDIOportsupprots8GPIO(4GPI+4GPO)• 1xMicroSDcardslot• 2xAudiojacks:Line-outandMic-in• 1xPowerLED• 1xPowerbutton• 2xAntennaholesfor3G/Wi-Fi

Back Panel I/O

• 1xHDMIport• 2xUSB2.0ports• 1xCOMportforRS-232(TX/RX)• 1x10/100MbpsEthernetport• 1xDC-injack• 2xAntennaholesfor3G/Wi-Fi

Onboard Connector

• 1xUSB2.0connector• 1xUART(Debug)connector• 1xminiPCIeslot• 1xSIMcardslot

Power Supply

• 12VDC-in

Operating System

• Android5.0,LinuxKernel3.4.5

VIA Smart ETK

• GPIO,UART,Watchdogtimer

Operating Temperature

• 0°C ~ 50°C

Operating Humidity

• 0%~90%@45°C(non-condensing)

Storage Temperature

• -10°C~60°C@90%(non-condensing)


4

Vibration Loading During Operation

• WithonboardeMMC:5Grms,IEC60068-2-64,random,5~500Hz,1hr/axis

Shock During Operation

• WithonboardeMMC:50G,IEC60068-2-27,halfsize,11msduration

Mechanical Contruction

• Metal top cover• Metalchassishousing

Mounting

• VESAMount(75mmx75mm)(NooptionalmountingkitwillbeprovidedbyVIA)

Dimensions

• 154.40mm(W)x27mm(H)x106.68mm(D)(6.08”x1.06”x4.20”)

Weight

• 0.50kg(1.10lbs)

Compliance

• CE• FCC

Notes:1.AstheoperatingtemperatureprovidedinthespecificationsisaresultofthetestperformedinVIA’schamber,anumberofvariablescaninfluencethisresult.Pleasenotethattheworkingtemperaturemayvarydependingontheactualsituationandenvironment.Itishighlysuggestedtoexecuteasolidtestingandtakeallthevariablesintoconsiderationwhenbuildingthesystem.Pleaseensurethatthesystemrunswellundertheoperatingtemperatureintermsofapplication.

2.PleasenotethatthelifespanoftheonboardeMMCmemorychipmayvarydependingontheamountofaccess.MorefrequentandlargerdataaccessoneMMCmemorymakesitslifespanshorter.Therefore,itishighlyrecommendedtouseareplaceableexternalstorage(e.g.,MicroSDcard)forlargedataaccess.


5

1.3 LayoutDiagram

Figure1:FrontpanelI/Olayout

Figure2:BackpanelI/Olayout

DIO

Power LED

Line-out Power Bu�on

Micro USB 2.0 OTG

Micro SD Card Slot

Antenna Hole

Mic-in

Antenna Hole

COM

10/100Mbps Ethernet

HDMI USB 2.0

DC-in

Antenna Hole

Antenna Hole


6

1.4 Dimensions

Figure3:DimensionsofARTiGOA630(Frontview)

Figure4:DimensionsofARTiGOA630(Rightview)

154.40mm

27mm

106.68mm


7

2. ExternalI/OPinDescriptionsandFunctionalityThischapterprovidesinformationabouttheARTiGOA630’sexternalI/Oportsandtheirfunctionality.

2.1 HDMI® PortTheARTiGOA630comeswithanHDMIportonthebackpanelwhichfeaturesanHDMIportTypeAreceptacleconnectorthatisusedtoconnecthighdefinitionvideoanddigitalaudiousingasinglecable.ThepinoutoftheHDMIportisshownbelow.

Table1:HDMIportpinouts

2.2 USB 2.0 PortTheARTiGOA630comeswithtwoexternalUSB2.0portsonthebackpanelwhichprovidescompletePlugandPlayandhotswapcapabilityforexternaldevices.TheUSBinterfacecomplieswithUSBUHCI,Rev.2.0.ThepinoutofthetypicalUSB2.0portisshownbelow.

Table2:USB 2.0 port pinouts

Pin Signal Pin Signal1 HDMI2+ 2 GND3 HDMI2- 4 HDMI1+5 GND 6 HDMI1-7 HDMI0+ 8 GND9 HDMI0- 10 HDMICLK+

11 GND 12 HDMICLK-13 HDMICEC 14 NC15 HDMIDDCSCL 16 HDMIDDCSDA17 GND 18 5V_HDMI19 HDMIHPD

119

218

USB0Pin Signal1 VCC2 USB data -3 USBdata+4 GND

14

14

Figure5:HDMIportdiagram

Figure6:USB2.0portdiagram

USB1Pin Signal1 VCC2 USB data -3 USBdata+4 GND


8

2.3 Micro USB 2.0 OTG PortTheARTiGOA630comeswithaMicroUSB2.0typeBportlocatedonthefrontpanelwhichsupportsOTGanditoffersexpandablestorage.ThepinoutoftheMicroUSB2.0OTGportisshownbelow.

Table3:Micro USB 2.0 OTG port pinouts

2.4 DIOPortTheARTiGOA630comeswithafemaleDIOportfordigitalI/OcommunicationinterfacewhichfeaturesaD-sub15-pinconnector.ThepinoutoftheDIOportisshownbelow.

Table4:DIOportpinouts

Pin Signal1 USB_VBUS02 USB_HD0-3 USB_HD0+4 USBID05 GND

5 1

Pin Signal1 GPIO12 GPIO23 GPIO34 GPIO55 GPIO66 GPIO77 GPIO88 GND9 NC

10 GPIO1211 GPIO1312 GPIO1413 VO_3314 VO_3315 GND

5 14 3 2

678910

1112131415

Figure7:MicroUSB2.0OTGportdiagram

Figure8:DIOportdiagram


9

2.5 10/100MbpsEthernetPortTheARTiGOA630comeswitha10/100MbpsEthernetport.Theintegrated10/100MbpsEthernetportusesan8Position8Contact(8P8C)receptacleconnector(commonlyreferredtoasRJ-45).Thepinoutofthe10/100MbpsEthernetportisshownbelow.

Table5:10/100MbpsEthernetportpinouts

The10/100MbpsEthernetporthastwoLEDindicatorslocatedonthefrontsidetoshowitsActive/Linkstatusand Speed status.

Table6:10/100MbpsEthernetportLEDcolordefinitions

Active LED(LeftLEDonRJ-45port)

Link LED(RightLEDonRJ-45port)

Linkoff LEDisoff LEDisoffSpeed_10Mbit TheGreenLEDisoff YellowFlashSpeed_100Mbit TheGreenLEDison YellowFlash

Pin Signal1 TD+2 TD-3 RD+4 REGOUT5 REGOUT6 RD-7 GND8 GND

18

Figure9:10/100MbpsEthernetportdiagram


10

2.6 Audio JackTheARTiGOA630offersHighDefinitionAudiothrougha3.5mmTRSjackonthefrontpanelwhichfeaturesaLine-outandMic-in.TheLine-outjackisforconnectingtoexternalspeakersorheadphones.TheMic-injackisforconnectingtoamicrophone.

2.7 Micro SD Card SlotTheARTiGOA630comeswithanMicroSDcardslotlocatedonthefrontpanelI/Owhichcansupportamaximumstoragecapacityof32GB.ThepinoutoftheMicroSDcardslotisshownbelow.

Table7:Micro SD card slot pinouts

Jack DescriptionMic-in TRSjack,3.5mmØ5P,90Degree,Female,shieldedLine-out TRSjack,3.5mmØ5P,90Degree,Female,shielded

Mic-in Line-out

Figure10:Audiojacksdiagram

9 1

Figure11:MicroSDcardslotdiagram

Pin Signal 1 SD0DATA22 SD0DATA33 SD0CMD4 VCC33_SDO5 SD0CLK6 GND7 SD0DATA08 SD0DATA19 SD0CD-


11

2.8 PowerOn/OffButtonTheARTiGOA630comeswithapowerbuttonwhichcansupportfourfunctions.Thetablebelowwillexplainhowthefunctionswork.

Table8:Powerbuttonbehaviordescriptions

2.9 DC-InJackTheARTiGOA630comeswithaDC-injackwhichcarriesa12VDCexternalpowerinput.ThespecificationandpinoutofpowerDC-injackisshownbelow.

Table9:DC-injackpinouts

Table10: DC-injackspecifications

Pin Signal 1 12VIN2 GND

Physical Specification Outer Diameter 6.0mmInnerDiameter 2.5mmBarrelDepth 8.20 mm

Electrical SpecificationInputVoltage +12V

Physical Specification Suspend/ResumeSystem Quicklypressthepowerbuttononcetosuspend.Whilein

suspendingmodequicklypressoncetoresume.Popup power control menu Occurswhenthepowerbuttonispressedforlongerthan3

seconds.Power On Whenthesystemisforcedtopoweroff,pressthepower

buttontopowerbackon.Reset mode Occurswhenthepowerbuttonispressedforlongerthan6

seconds.

2.5mm6.0mm

12

Figure12:Poweron/offbuttondiagram

Figure13:DC-injackdiagram

Figure14:DC-injackspecificationdiagram


12

2.10 Power LEDTheARTiGOA630isequippedwithaPowerLEDwhichislocatedonthefrontpanel.Itisgreenandindicatesthestatusofthesystem.

Figure15:PowerLEDdiagram


13

3. Onboard ConnectorThischapterprovidesinformationabouttheonboardconnectoroftheARTiGOA630system’smainboard.

3.1 USB 2.0 Connector TheARTiGOA630includesanonboardUSB2.0connectordesignedforconnectingtheEMIO-5531USBWi-Fi&Bluetoothmodule.TheUSB2.0connectorislabeledas“JUSB1”.ThepinoutoftheUSB2.0connectorisshownbelow.

Table11: USB 2.0 connector pinouts

Pin Signal1 NC2 -3 GND4 USBDt1+5 USBDT1-6 5VUSB1

LOCK

OPEN

JUSB1

1

1

Figure16:USB2.0connectordiagram


14

3.2 MiniPCIeSlotTheARTiGOA630isequippedwithminiPCIeslotforwirelessnetworkingoptionsuchasWi-Fi/Bluetooth/3GusingEMIO-2531andEMIO-2550modules.ThepinoutoftheminiPCIeslotisshownbelow.

Table12: MiniPCIeslotpinouts

Pin Signal Pin Signal1 NC 2 3.3V3 NC 4 GND5 NC 6 +1.5V7 3.3V 8 USIM_VCC9 GND 10 USIM_DATA

11 NC 12 USIM_CLK13 NC 14 USIM_RST15 GND 16 NC17 NC 18 GND19 NC 20 -W_DISABLE21 GND 22 SUSGP1O223 NC 24 3.3V25 NC 26 GND27 GND 28 +1.5V29 GND 30 12C4SCL31 NC 32 12C4SDA33 NC 34 GND35 GND 36 USBDT2-37 GND 38 USBDT2+39 3.3V 40 GND41 3.3V 42 NC43 GND 44 NC45 NC 46 NC47 NC 48 +1.5V49 NC 50 GND51 NC 52 3.3V

LOCK

OPEN

1

MINIPCIE1

Figure17:MiniPCIeslotdiagram


15

3.3 SIMCardSlotTheARTiGOA630isequippedwithaSIMcardslotthatcansupport3GSIMcard.UsingtheSIMcardslotontheARTiGOA630mainboardrequiresa3GmoduleinstalledintheminiPCIeslottoenablethe3Gfunction,otherwisetheSIMcardslotisdisabled.TheSIMcardslotisdesignedonlyfor3Gmodulewithoutbuilt-inSIMcardslotonit.TheSIMcardslotislabeledas“SIM1”.Thepinoutoftheslotisshownbelow.

Table13: SIMcardslotpinouts

3.4 UART Connector TheARTiGOA630includesoneUARTconnectorwhichisfordebuggingpurposes.Itislabeledas“J1”andhas10-pin.TheUARTconnectorpinoutsareshownbelow.

Table14: UART connector pinouts

Pin Signal1 USIM_VCC2 USIM_RST3 USIM_CLK4 -5 GND6 USIM_VCC7 USIM_DATA LOC

KOPEN

1

SIM1

Pin Signal1 UART0TXD2 UART0RXD3 SFCLK4 GND5 SFDO6 SFDI7 SFCS0-8 VCC_SF

LOCK

OPEN

J11

Figure18:SIMcardslotdiagram

Figure19:UARTconnectordiagram


16

4. HardwareInstallationThischapterprovidesyouwithinformationonthehardwareinstallationprocedures.Itisrecommendedtouseagroundedwriststrapbeforehandlingcomputercomponents.Electrostaticdischarge(ESD)candamagesomecomponents.

4.1 OpeningtheChassisStep 1

First,removethetwoscrewsfromleft&rightsideofthechassisthenremovethescrewfromtopofthechassis.LastlymakesuretoremovetheHexStandoffscrewsfromtheDIOport.

Figure20:Unscrewingthetopcover


17

Step 2

Gentlyslidethetopcoverhorizontallytodisengageitfromthechassisandpulluptoremoveitcompletely.

Figure21:Removingthetopcover


18

4.2 InstallingtheRubberfeetStep 1

Locatethedesignatedareasfortherubberfeetatthebottomsideofthechassis.

Step 2

Attachedcarefullyeachrubberfootandfirmlypressitdowntoensurethattherubberfootisproperlyinplace.

Figure22:Installingrubberfeet


19

5. SoftwareandTechnicalSupport5.1 Android SupportTheARTiGOA630featuresacompletesignagesoftwareevaluationimagefeaturingAndroid5.1operatingsystem.

5.2 LinuxSupportTheARTiGOA630featuresacompletesignagesoftwareevaluationimagefeaturingLinuxKernel3.4.5operatingsystem.

5.3 TechnicalSupportsandAssistance•Forutilitiesdownloads,latestdocumentationandnewinformationabouttheARTiGOA630,pleasevisitourwesbiteatwww.viatech.com.

•Fortechnicalsupportandadditionalassistance,alwayscontactyourlocalsalesrepresentativeor boarddistributor,orgotohttps://www.viatech.com/en/support/driver-support-faq/technical-support/ for technicalsupport.

•ForOEMclientsandsystemintegratorsdevelopingaproductforlongtermproduction,other code and resources may also be made available. Please visit our webiste at https://www.viatech.com/en/ about/contact/tosubmitarequest.


20

AppendixA. InstallingWirelessAccessoriesThischapterprovidesyouwithinformationonhowtoinstalltheEMIOmodules(5531,2531,&2550)intheARTiGOA630system.Itisrecommendedtouseagroundedwriststrapbeforehandlingcomputercomponents.Electrostaticdischarge(ESD)candamagesomecomponents.

A.1. InstallingtheEMIO-5531USBWi-Fi&Bluetoothmodule

Step 1

Followtheinstructionsinsection4.1abovetoopenthechassis.

Step 2

Locatethepre-mountedstandoffsfortheEMIO-5531moduleontheboard.

Step 3

MounttheEMIO-5531moduleontheboard.AlignthetwomountingholesontheEMIO-5531modulewiththemountingholesonthestandoffs.AndthensecuretheEMIO-5531moduleinplacewithtwoscrews.

Figure23:InstallingtheEMIO-5531module

LOCK

OPEN

1

2


21

Step 4

AttachtheUSBWi-Ficable(P/N99G33-193126)totheonboardUSBWi-Ficonnector(JUSB1)andthenconnecttheotherendofthecabletotheEMIO-5531module.Nextremovetheantennaholecover.

Figure24:ConnectingtheUSBWi-Ficableandremovingantennaholecover

Step 5

InserttheWi-Fiantennacableintotheantennaholefrominsideofthebackpanelplate.Insertthetoothedwasher,fastenitwiththenutandinstalltheexternalantenna.

Figure25:InstallingantennaandantennacableofEMIO-5531module

LOCK

OPEN1

2

3

LOCK

OPEN

1

234


22

Step 6

ConnecttheotherendoftheWi-Fiantennacabletothemicro-RFconnectorlabeled“MH2”ontheEMIO-5531module.

Figure26:Connectingtheantennacabletothemicro-RFconnectoronEMIO-5531module

Step 7

Reinstallthetopcover.

LOCK

OPEN

CKOPEN

LOC


23

A.2. InstallingtheEMIO-2531miniPCIeWi-Fimodule& BluetoothmoduleStep 1

Followtheinstructionsinsection4.1abovetoopenthechassis.

Step 2

AlignthenotchontheEMIO-2531modulewiththecounterpartontheminiPCIeslottheninsertthemoduleat30°angle.

Figure27:InsertingEMIO-2531module

LOCK

OPEN

30


24

Step 3

Oncethemodulehasbeenfullyinserted,pushdownthemoduleuntilthescrewholesalignwiththemountingholeonthestandoffandthensecurethemodulewithascrewtothestandoff.Lastly,removetheantennaholecover.

Figure28:SecuringtheEMIO-2531moduleandremovingtheantennacover

Step 4

InserttheWi-Fiantennacableintotheantennaholefrominsideofthebackpanelplate.Insertthewasher,fastenitwiththenutandinstalltheexternalantenna.


LOCK

OPEN

1

2

LOCK

OPEN

1

234


25

Step 5

GentlyconnecttheotherendoftheWi-Fiantennacabletothemicro-RFconnectorlabeled“MH2”ontheEMIO-2531module.

Figure30:Connectingtheantennacabletothemicro-RFconnectoronEMIO-2531

Step 6


LOCK

OPEN


26

A.3. InstallingtheEMIO-2550miniPCIeMobileBroadband module

Step 1

Pleasefollowtheinstructionsinsection4.1abovetoopenthechassis.

Step 2

OpenandpulluptheslottheninsertanactiveSIMcardinsidetheslot.EnsuretheangledcorneroftheSIMcardisplacedinthecorrectwaybeforeclosingtheslot.

Figure31:InstallingtheSIMcard

LOCK

OPEN

1 2 3 4

Open

Lock


27

Step 3

AlignthenotchontheEMIO-2550miniPCIemodulewiththecounterpartontheminiPCIeslottheninsertthemoduleat30°angle.

Figure32:InsertingEMIO-2550module

Step 4

Oncethemodulehasbeenfullyinserted,pushdownthemoduleuntilthescrewholesalignwiththemountingholeonthestandoffandthensecurethemodulewithascrewtothestandoff.Lastly,removetheantennaholecover.

Figure33:SecuringtheEMIO-2550moduleandremovingantennaholecover

LOCK

OPEN

12

LOCK

OPEN


28

Step 5

Insertthe3Gantennacableintotheantennaholefrominsideofthebackpanelplate.Insertthewasher,fastenitwiththenutandinstalltheexternalantenna.


Step 6

Gentlyconnecttheotherendofthe3Gantennacabletothemicro-RFconnectorlabeled“MAN”ontheEMIO2550 module.

Figure35:Connectingtheantennacabletothemicro-RFconnectoronEMIO-2550module

Step 7


LOCK

OPEN

1

234

LOCK

OPEN

1F, 531 Zhong-zheng Road,Xindian Dist., New Taipei City 231Taiwan

Tel: 886-2-2218-5452Fax: 886-2-2218-9860Email: [email protected]

940 Mission CourtFremont, CA 94539,USA


Email: [email protected]

Taiwan Headquarters USA

Europe

Tsinghua Science Park Bldg. 7No. 1 Zongguancun East Road,Haidian Dist., Beijing, 100084China

Tel: 86-10-59852288Fax: 86-10-59852299Email: [email protected]

3-15-7 Ebisu MT Bldg. 6F,Higashi, Shibuya-kuTokyo 150-0011Japan


ChinaJapan

user manual artigo a630 - docid81hrs3j1.cloudfront.net · iv artigo a630 user manual bo contents 1...

Documents