user manual idm-1104hn-35xga1e(xga) -...
TRANSCRIPT
User Manual
IDM-1104HN-35XGA1E(XGA)
10.4” TFT Liquid Crystal Display Module
CopyrightThe documentation and the software included with this product are copyrighted 2016by Advantech Co., Ltd. All rights are reserved. Advantech Co., Ltd. reserves the rightto make improvements in the products described in this manual at any time withoutnotice. No part of this manual may be reproduced, copied, translated or transmittedin any form or by any means without the prior written permission of Advantech Co.,Ltd. Information provided in this manual is intended to be accurate and reliable. How-ever, Advantech Co., Ltd. assumes no responsibility for its use, nor for any infringe-ments of the rights of third parties, which may result from its use.
AcknowledgementsIntel and Pentium are trademarks of Intel Corporation.
Microsoft Windows and MS-DOS are registered trademarks of Microsoft Corp.
All other product names or trademarks are properties of their respective owners.
Product Warranty (2 years)Advantech warrants to you, the original purchaser, that each of its products will befree from defects in materials and workmanship for two years from the date of pur-chase.
This warranty does not apply to any products which have been repaired or altered bypersons other than repair personnel authorized by Advantech, or which have beensubject to misuse, abuse, accident or improper installation. Advantech assumes noliability under the terms of this warranty as a consequence of such events.
Because of Advantech’s high quality-control standards and rigorous testing, most ofour customers never need to use our repair service. If an Advantech product is defec-tive, it will be repaired or replaced at no charge during the warranty period. For out-of-warranty repairs, you will be billed according to the cost of replacement materials,service time and freight. Please consult your dealer for more details.
If you think you have a defective product, follow these steps:
1. Collect all the information about the problem encountered. (For example, CPU speed, Advantech products used, other hardware and software used, etc.) Note anything abnormal and list any onscreen messages you get when the problem occurs.
2. Call your dealer and describe the problem. Please have your manual, product, and any helpful information readily available.
3. If your product is diagnosed as defective, obtain an RMA (return merchandize authorization) number from your dealer. This allows us to process your return more quickly.
4. Carefully pack the defective product, a fully-completed Repair and Replacement Order Card and a photocopy proof of purchase date (such as your sales receipt) in a shippable container. A product returned without proof of the purchase date is not eligible for warranty service.
5. Write the RMA number visibly on the outside of the package and ship it prepaid to your dealer.
Part No. 2006110400 Edition 1
Printed in Taiwan February 2016
IDM-1104 User Manual ii
Technical Support and Assistance1. Visit the Advantech website at http://support.advantech.com where you can find
the latest information about the product.2. Contact your distributor, sales representative, or Advantech's customer service
center for technical support if you need additional assistance. Please have the following information ready before you call:– Product name and serial number– Description of your peripheral attachments– Description of your software (operating system, version, application software,
etc.)– A complete description of the problem– The exact wording of any error messages
Warnings, Cautions and Notes
Document FeedbackTo assist us in making improvements to this manual, we would welcome commentsand constructive criticism. Please send all such - in writing to: [email protected]
Packing ListBefore setting up the system, check that the items listed below are included and ingood condition. If any item does not accord with the table, please contact your dealerimmediately.
18pcs LCD modules / 1 Box Box dimensions: 465 (L) X 362 (W) X 314 (H) mm Weight: approximately 8.3Kg (18 modules per box)
Warning! Warnings indicate conditions, which if not observed, can cause personal injury!
Caution! Cautions are included to help you avoid damaging hardware or losing data. e.g.
There is a danger of a new battery exploding if it is incorrectly installed. Do not attempt to recharge, force open, or heat the battery. Replace the battery only with the same or equivalent type recommended by the man-ufacturer. Discard used batteries according to the manufacturer's instructions.
Note! Notes provide optional additional information.
iii IDM-1104 User Manual
Safety Instructions1. Read these safety instructions carefully.2. Keep this User Manual for later reference.3. Disconnect this equipment from any AC outlet before cleaning. Use a damp
cloth. Do not use liquid or spray detergents for cleaning.4. For plug-in equipment, the power outlet socket must be located near the equip-
ment and must be easily accessible.5. Keep this equipment away from humidity.6. Put this equipment on a reliable surface during installation. Dropping it or letting
it fall may cause damage.7. The openings on the enclosure are for air convection. Protect the equipment
from overheating. DO NOT COVER THE OPENINGS.8. Make sure the voltage of the power source is correct before connecting the
equipment to the power outlet.9. Position the power cord so that people cannot step on it. Do not place anything
over the power cord.10. All cautions and warnings on the equipment should be noted.11. If the equipment is not used for a long time, disconnect it from the power source
to avoid damage by transient overvoltage.12. Never pour any liquid into an opening. This may cause fire or electrical shock.13. Never open the equipment. For safety reasons, the equipment should be
opened only by qualified service personnel.14. If one of the following situations arises, get the equipment checked by service
personnel:The power cord or plug is damaged.Liquid has penetrated into the equipment.The equipment has been exposed to moisture.The equipment does not work well, or you cannot get it to work according to
the user's manual.The equipment has been dropped and damaged.The equipment has obvious signs of breakage.
15. DO NOT LEAVE THIS EQUIPMENT IN AN ENVIRONMENT WHERE THE STORAGE TEMPERATURE MAY GO BELOW -20° C (-4° F) OR ABOVE 60° C (140° F). THIS COULD DAMAGE THE EQUIPMENT. THE EQUIPMENT SHOULD BE IN A CONTROLLED ENVIRONMENT.
16. CAUTION: DANGER OF EXPLOSION IF BATTERY IS INCORRECTLY REPLACED. REPLACE ONLY WITH THE SAME OR EQUIVALENT TYPE RECOMMENDED BY THE MANUFACTURER, DISCARD USED BATTERIES ACCORDING TO THE MANUFACTURER'S INSTRUCTIONS.
The sound pressure level at the operator's position according to IEC 704-1:1982 isno more than 70 dB (A).
DISCLAIMER: This set of instructions is given according to IEC 704-1. Advantechdisclaims all responsibility for the accuracy of any statements contained herein.
IDM-1104 User Manual iv
Safety Precaution - Static ElectricityFollow these simple precautions to protect yourself from harm and the products fromdamage.
To avoid electrical shock, always disconnect the power from your PC chassis before you work on it. Don't touch any components on the CPU card or other cards while the PC is on.
Disconnect power before making any configuration changes. The sudden rush of power as you connect a jumper or install a card may damage sensitive elec-tronic components.
PRECAUTIONS
ASSEMBLY AND HANDLING PRECAUTIONS
1. Do not apply rough force such as bending or twisting to the module during assembly.
2. It is recommended to assemble or to install a module into the user’s system in clean working areas.The dust and oil may cause electrical short or worsen the polarizer.
3. Do not apply pressure or impulse to the module to prevent the damage of LCD panel and Backlight.
4. Always follow the correct power-on sequence when the LCD module is turned on. This can prevent the damage and latch-up of the CMOS LSI chips.
5. Do not plug in or pull out the I/F connector while the module is in operation.6. Do not disassemble the module.7. Use a soft dry cloth without chemicals for cleaning, because the surface of
polarizer is very soft and easily scratched.8. Moisture can easily penetrate into LCD module and may cause the damage dur-
ing operation.9. High temperature or humidity may deteriorate the performance of LCD module.
Please store LCD modules in the specified storage conditions.10. When ambient temperature is lower than 10ºC, the display quality might be
reduced. For example, the response time will become slow, and the starting voltage of backlight will be higher than that of room temperature.
11. Do not keep same pattern in a long period of time. It may cause image sticking on LCD.
SAFETY PRECAUTIONS
1. The startup voltage of a Backlight is approximately 1000 Volts. It may cause an electrical shock while assembling with the inverter. Do not disassemble the module or insert anything into the Backlight unit.
2. If the liquid crystal material leaks from the panel, it should be kept away from the eyes or mouth. In case of contact with hands, skin or clothes, it has to be washed away thoroughly with soap.
3. After the module’s end of life, it is not harmful in case of normal operation and storage.
v IDM-1104 User Manual
IDM-1104 User Manual vi
Contents
Chapter 1 General Description ............................11.1 Overview ................................................................................................... 21.2 Features .................................................................................................... 21.3 Application................................................................................................. 21.4 General Specifications .............................................................................. 21.5 Mechanical Specifications......................................................................... 31.6 Dimensions ............................................................................................... 3
Chapter 2 Absolute Maximum Ratings ...............52.1 Absolute Ratings Of Environment ............................................................. 62.2 Electrical Absolute Ratings ....................................................................... 6
2.2.1 TFT LCD Module .......................................................................... 62.2.2 LED Converter .............................................................................. 7
Chapter 3 Electrical Characteristics....................93.1 TFT LCD Module..................................................................................... 103.2 LED Converter ........................................................................................ 12
Chapter 4 Block Diagram ...................................134.1 TFT LCD Module..................................................................................... 14
Chapter 5 Interface Pin Assignment .................155.1 TFT LCD Module..................................................................................... 165.2 Backlight Unit (Converter Connector Pin) ............................................... 175.3 Color Data Input Assignment .................................................................. 17
Chapter 6 Interface Timing.................................196.1 Input Signal Timing Specifications .......................................................... 206.2 Power ON/OFF Sequence ...................................................................... 216.3 The Input Data Format ............................................................................ 226.4 Scanning Direction .................................................................................. 23
Chapter 7 Optical Characteristics .....................257.1 Test Conditions ....................................................................................... 267.2 Optical Specifications.............................................................................. 26
Chapter 8 Reliability Test Criteria......................318.1 Reliability Test Criteria ............................................................................ 32
Chapter 9 Packaging...........................................33
vii IDM-1104 User Manual
9.1 Packing Method ...................................................................................... 34
IDM-1104 User Manual viii
Chapter 1
1 General Description1.1 OverviewIDM-1104HN-35XGA1E(XGA) is made by Innolux G104X1-L03 which is a 10.4" TFTLiquid Crystal Display module with LED backlight unit and 30-pin-and-1ch LVDSinterface. This product supports 1024 x 768 XGA format and can display true 16.2Mcolors (6-bits colors with FRC). The converter module for LED backlight is built-in.
1.2 Features Excellent brightness (350 nits) Ultra high contrast ratio (1000:1) Fast response time (Ton+Toff average 25 ms)
High color saturation NTSC 57% XGA (1024 x 768 pixels) resolution DE (Data Enable) only mode LVDS (Low Voltage Differential Signaling) interface Ultra wide viewing angle: 176(H)/ 176(V) (CR>10) Super MVA technology 180 degree rotation display option Color reproduction (Nature color) Wide operation and storage temperature range
1.3 Application TFT LCD monitor for Industrial applications Slim design display for portable applications Digitizer Applicable Design
1.4 General Specifications
Item Specification Unit Note
Active Area 210.4 (H) x 157.8 (V) (10.4” diagonal) mm (1)
Bezel Opening Area 215.4 (H) x 161.8 (V) mm
Driver Element a-si TFT active matrix - -
Pixel Number 1024 x R.G.B. x 768 pixel -
Pixel Pitch (Sub Pixel) 0.0685 (H) x 0.2055 (V) mm -
Pixel Arrangement RGB vertical stripe - -
Display Colors 16.2 M color -
Display Operation Mode Transmissive mode / Normally black - -
Surface Treatment Anti Glare - -
Total power consumption (typ)
5.1 W typ
Note1! Please refer to the attached drawings for more information of front and back outline dimensions.
IDM-1104 User Manual 2
Chapter 1
GeneralD
escription
1.5 Mechanical Specifications
1.6 Dimensions
Item Min. Typ. Max. Unit Note
Module Size
Horizontal (H) - 238.6 - mm(1)
Vertical (V) - 175.8 - mm
Depth (D) - 7.5 - mm -
Weight - 280 - g -
Note! Please refer to the attached drawings for more information of front and back outline dimensions.
Unit: mm
238.6 ±0.5233.4227
113.5 1.43.3
6
41.5 1.5
1.5
5.86.61
3.57
4
1.53.57
7.47±0.5 (Max)
6.615.8
5.8
8.2
233.42.6
5.8XC
5.85.8
5.8
5.8
5.8
5.8
14.9
24.9
34.9
7.5
28.9
11.9
30
C
0.5
14.9
6.5
6.9
29.9
24.9
87.4
150
145
215.4 ±0.2 (Opening Area)
161.
8 ±
0.2
(Op
enin
g A
rea)
175.
8 ±
0.5
Active Area (210.432 x 157.824)
Active Area Center
4-Ø2.8 User Hole
3 IDM-1104 User Manual
IDM-1104 User Manual 4
Chapter 2
2 Absolute Maximum Ratings2.1 Absolute Ratings Of Environment
2.2 Electrical Absolute Ratings
2.2.1 TFT LCD Module
Item SymbolValue
Unit NoteMin. Max.
Operating Ambient Temperature
TOP -20 +70 ºC
Storage Temperature TST -20 +70 ºC
Note! 1. Temperature and relative humidity range is shown in the figure below.
90 %RH Max. (Ta ≤ 40 ºC). Wet-bulb temperature should be 39 ºC Max. (Ta > 40 ºC). No condensation
Relative Humidity (%RH)
Operating Range
Temperature (ºC)
100
80 60 -20 40 0 20 -40
90
70
40
60
2010 Storage Range
Item SymbolValue
Unit NoteMin. Max.
Power Supply Voltage VCC -0.3 7 V (1)
IDM-1104 User Manual 6
Chapter 2
Absolute
Maxim
umR
atings
2.2.2 LED Converter
Item SymbolValue
Unit NoteMin. Max.
Converter Voltage Vi -0.3 22 V (1), (2)
Enable Voltage EN - 5.5 V
Backlight Adjust ADJ - 5.5 V
Note1! Permanent damage to the device may occur if maximum values are exceeded. Function operation should be restricted to the conditions described under Normal Operating Conditions.
Note2! Specified values are for LED light bar (Refer to 3.2 for further informa-tion).
7 IDM-1104 User Manual
IDM-1104 User Manual 8
Chapter 3
3 Electrical Characteristics3.1 TFT LCD ModuleTa = 25 ± 2 ºC
Parameter SymbolValue
Unit NoteMin. Typ. Max.
Power Supply Voltage VCC 3.0 3.3 3.6 V (1)
Rush Current IRUSH - - 4.0 A (2)
Power Supply Cur-rent
White-
530 570 620 mA(3)
Black 380 420 460 mA
Power Consumption PL --- 1.9 --- W
LVDS differential input voltage |VID| 100 - 600 mV -
LVDS common input voltage VICM 0.7 - 1.6 V -
Note1! Permanent damage to the device may occur if maximum values are exceeded. Function operation should be restricted to the conditions described under Normal Operating Conditions.
Note2! Specified values are for LED light ba (Refer to 3.2 for further informa-tion).
R1
(High to Low)
(Control Signal)
+12V
SW
Q2
C1
1uF
Vcc
+3.3V
2SK1470
Q1 2SK1475
47K
R2
1K
VR147K C2
0.01uF
C3
1uF
FUSE(LCD Module Input)
IDM-1104 User Manual 10
Chapter 3
ElectricalC
haracteristics
Note! The specified power supply current is under the conditions at Vcc = 3.3 V, Ta = 25 ± 2 ºC, fv = 60Hz, whereas a power dissipation check pattern below is displayed.
VCC rising time is 470us
470μs
+3.3V
GND
0.9Vcc
0.1Vcc
Active Area
c. Vertical Stripe Pattern
R
R
R
R
R R
R
R
G
G
G
G
B
B
B
B
B
B
G
G
G
G
B
B
B
B
R
R
Active Area Active Area
a. White Pattern b. Black Pattern
11 IDM-1104 User Manual
3.2 LED ConverterTa = 25 ± 2 ºC
Parameter SymbolValue
Unit NoteMin. Typ. Max.
Converter Power Supply Voltage Vi 7 12.0 17 V (Duty 100%)
Converter Power Supply Current Ii --- 0.28 --- A @ Vi = 12V(Duty 100%)
LED Power Consumption PLED --- 3.1 --- W@ Vi = 12V(Duty 100%)
EN Control Level
Backlight on
2.0 --- 5 V
Backlight off
0 --- 0.8 V
PWM Control Level
PWM High Level
2.0 --- 5 V
PWM Low Level
0 --- 0.15 V
PWM Control Duty Ratio 2 100 %
PWM Control Frequency fPWM 190 200 20k Hz (2)
LED Life Time LL 30,000 Hrs (3)
Note1! LED current is measured by utilizing a high frequency current meter as shown below:
Note2! At 190 ~1KHz PWM control frequency, duty ratio range is restricted from 2% to 100%.
1K ~20KHz PWM control frequency, minimum duty on-time ≥ 20 us.
Note3! The lifetime of LED is defined as the time when it continues to operate under the conditions at Ta = 25 ±2 °C and ILED = 20mADC (LED forward
current) until the brightness becomes ≤ 50% of its original value. Operat-ing LED under high temperature environment will reduce life time and lead to color shift.
Power Supply Converter
LED
Backlight
Unit
Vi, Ii
GND
Vo, Io
Input Power
Pi
Output Power
Po
IDM-1104 User Manual 12
Chapter 4
4 Block Diagram4.1 TFT LCD Module
TFT LCD PANEL (1024x3x768)
DATA DRIVER IC SC
AN
DR
IVER IC
DC/DC CONVERTER &
REFERENCE VOLTAGE
INPU
T CO
NN
ECTO
R
(JAE,FI-XB
30SRL-H
F11)
RX0(+/-)
RX1(+/-)
RX2(+/-)
RX3(+/-)
RXCLK(+/-)
TIMING
CONTROLLER
VCC
SEL 6/8
RPFI
GND
Converter LED BACKLIGHT UNIT
CONVERTER CONNECTOR(Connector, 91208-01001, 1.0mm, WTB, 10pin, Aces) Vi
IDM-1104 User Manual 14
Chapter 5
5 Interface Pin Assignment5.1 TFT LCD ModuleCN1 Connector Pin Assignment
Pin No. Symbol Description Note
1 VCC - Power supply: +3.3V -
2 VCC Power supply: +3.3V -
3 VCC VCC Power supply: +3.3V -
4 GND Ground -
5 GND Ground -
6 GND Ground -
7 RPFI Reverse Panel Function (Display Rotation)
( 2 )
8 NC No Connection
9 NC No Connection
10 NC No Connection
11 SEL6/8LVDS 6/8 bit select function control, Low or NC -> 8 bit Input ModeHigh -> 6bit Input Mode
( 2 )
12 GND Ground -
13 NC No Connection -
14 GND Ground -
15 RX0- Negative transmission data of pixel 0 -
16 RX0+ Positive transmission data of pixel 0 -
17 GND Ground -
18 RX1- Negative transmission data of pixel 1 -
19 RX1+ Positive transmission data of pixel 1 -
20 GND Ground -
21 RX2- Negative transmission data of pixel 2 -
22 RX2+ Positive transmission data of pixel 2 -
23 GND Ground -
24 RXCLK- Negative of clock -
25 RXCLK+ Positive of clock -
26 GND Ground -
27 RX3- Negative transmission data of pixel 3 -
28 RX3+ Positive transmission data of pixel 3 -
29 GND Ground -
30 NC No Connection ( 2 )
Note1! Connector Part No.: JAE, FI-XB30SRL-HF11 or compatible connector
Note2! “Low” stands for 0V. “High” stands for 3.3V. “NC” stands for “No Con-nected”
IDM-1104 User Manual 16
Chapter 5
InterfaceP
inA
ssignment
5.2 Backlight Unit (Converter Connector Pin)
5.3 Color Data Input AssignmentThe brightness of each primary color (red, green and blue) is based on the 8-bit grayscale data input for the color. The higher the binary input, the brighter the color. Thetable below provides the assignment of color versus data input.
Pin Symbol Description Remark
1 Vi Converter input voltage 12V
2 Vi Converter input voltage 12V
3 Vi Converter input voltage 12V
4 Vi Converter input voltage 12V
5 VGND Converter ground Ground
6 VGND Converter ground Ground
7 VGND Converter ground Ground
8 VGND Converter ground Ground
9 EN Enable pin 3.3V
10 ADJ Backlight Adjust PWM Dimming
Color
Data Signal
Red Green Blue
R7 R6 R5 R4 R3 R2 R1 R0 G7 G6 G5 G4 G3 G2 G1 G0 B7 B6 B5 B4 B3 B2 B1 B0
BasicColors
Black Red Green Blue Cyan Magenta YellowWhite
01000111
01000111
01000111
01000111
01000111
01000111
01000111
01000111
00101011
00101011
00101011
00101011
00101011
00101011
00101011
00101011
00011101
00011101
00011101
00011101
00011101
00011101
00011101
00011101
Gray Scale Of Red
Red(0) / DarkRed(1) Red(2):: Red(253) Red(254)Red(255)
000::111
000::111
000::111
000::111
000::111
000::111
001::011
010::101
000::000
000::000
000::000
000::000
000::000
000::000
000::000
000::000
000::000
000::000
000::000
000::000
000::000
000::000
000::000
000::000
Gray Scale Of Green
Green(0) / Dark Green(1) Green(2):: Green(253) Green(254)Green(255)
000::000
000::000
000::000
000::000
000::000
000::000
000::000
000::000
000::111
000::111
000::111
000::111
000::111
000::111
001::011
010::101
000::000
000::000
000::000
000::000
000::000
000::000
000::000
000::000
17 IDM-1104 User Manual
Gray Scale Of Blue
Blue(0) / Dark Blue(1) Blue(2):: Blue(253) Blue(254)Blue(255)
000::000
000::000
000::000
000::000
000::000
000::000
000::000
000::000
000::000
000::000
000::000
000::000
000::000
000::000
000::000
000::000
000::111
000::111
000::111
000::111
000::111
000::111
001::011
010::101
Note! 0: Low Level Voltage, 1: High Level Voltage
IDM-1104 User Manual 18
Chapter 6
6 Interface Timing6.1 Input Signal Timing SpecificationsThe input signal timing specifications are shown as in the following table and timingdiagram.
Signal ItemSymbol
Min. Typ. Max. Unit Note
DCLK Frequency Fc 55 65 75 MHZ
Vertical Active Display Term
Total Tv 770 806 950 ThTv=Tvd+Tvb
Display Tvd 768 768 768 Th -
Blank Tvb 2 38 182 Th -
Horizontal Active Display Term
Total Th 1104 1344 1800 TcTh=Thd+Thb
Display Thd 1024 1024 1024 Tc -
Blank Thb 76 320 776 Tc -
Note1! Since this assembly is operated in DE only mode, Hsync and Vsync input signals should be set to low logic level. Otherwise, this assembly would operate abnormally.
Note2! Frame rate is 60Hz
TvdTvb
Tv
Th
INPUT SIGNAL TIMING DIAGRAM
DE
Thb
Valid display data
Tc
DCLK
Thd
DE
DATA
IDM-1104 User Manual 20
Chapter 6
InterfaceT
iming
6.2 Power ON/OFF SequenceTo prevent a latch-up or DC operation of LCD assembly, the power on/off sequenceshould be as in the diagram below.
Note1! Please avoid floating state of interface signal at invalid period.
Note2! When the interface signal is invalid, be sure to pull down the power sup-ply of LCD VCC to 0 V.
Note3! The Backlight converter power must be turned on after the power supply for the logic and the interface signal is valid. The Backlight converter power must be turned off before the power supply for the logic and the interface signal is invalid.
Parameter Value
UnitsMin Typ Max
T1 0.5 - 10 ms
T2 0 - 50 ms
T3 0 - 50 ms
T4 500 - - ms
T5 200 - - ms
T6 20 - - ms
T7 5 - 300 ms
T8 10 - - ms
T9 10 - - ms
LVDS
VCC
Vi
10%
90%
T2T1
T3
0.1VCC
0.9VCC 0.9VCC
0.1VCC
T4VALID
T7
0.9Vi 0.9Vi
0.1Vi 0.1Vi
PWM DIMMING
T9
10%
90%
T8
BL ON/OFF
T5
10%
90%
T6
Power ON/OFF sequence
21 IDM-1104 User Manual
6.3 The Input Data Format
Note1! R/G/B data 7: MSB, R/G/B data 0: LSB
Note2! Please follow PSWG
Signal Nme Description Remark
R7R6R5R4R3R2R1R0
Red Data7(MSB)Red Data6Red Data5Red Data4Red Data3Red Data2Red Data1Red Data0(LSB)
Red-pixel DataEach red pixel data consists of these 8 bits pixel data.
G7G6G5G4G3G2G1G0
Green Data7(MSB)Green Data6Green Data5Green Data4Green Data3Green Data2Green Data1Green Data0(LSB)
Green-pixel DataEach green pixel data consists of these 8 bits pixel data.
IDM-1104 User Manual 22
Chapter 6
InterfaceT
iming
6.4 Scanning DirectionThe following figures show the image see from the front view. The arrow indicates thedirection of scan.
B7B6B5B4B3B2B1B0
Blue Data7(MSB)Blue Data6Blue Data5Blue Data4Blue Data3Blue Data2Blue Data1Blue Data0(LSB)
Blue-pixel DataEach blue pixel data consists of these 8 bits pixel data.
RXCLKIN+LVDS Clock Input
RXCLKIN-
DE Display Enable
VS Vertical Sync
HS Horizontal Sync
Note3! Output signals from any system shall be low or Hi-Z state when VCC is off
RPFI = Low/floating; normal display (default) RPFI = high: display with 180degree rotation
23 IDM-1104 User Manual
IDM-1104 User Manual 24
Chapter 7
7 Optical Characteristics7.1 Test Conditions
7.2 Optical SpecificationsThe relative measurement methods of optical characteristics are shown in 7.2. Thefollowing items should be measured under the test conditions described in 7.1 andstable environment shown in Note (6).
Item Symbol Value Unit
Ambient Temperature Ta 25±2 oC
Ambient Humidity Ha 50±10 %RH
Supply Voltage Vcc 5 V
Input SignalAccording to typical value in "3. ELECTRICAL CHARACTERIS-TICS"
Converter Current IL 20±1mA mA
Item Symbol Condition Min. Typ. Max. Unit Note
Contrast Ratio CR
θx=0°, θY =0°
Viewing angle at normal direction
700 1000 - (2)
Response TimeTR - 14 19 ms
(3)TF - 11 16 ms
Center Luminance of White LC 300 350 - 2 cd/m2 (4)
White Variation δW - - 1.4 - (7)
Cross Talk CT - - 4 % (5)
Chromaticity
RedRx
Typ.-0.05
0.610
Typ.+0.05
-
(6)
Ry 0.365 -
GreenGx 0.341 -
Gy 0.564 -
BlueBx 0.147 -
By 0.087 -
WhiteWx 0.313 -
Wy 0.329 -
ViewingAngle
Horizontalθx+
CR≥10
80 88 -
Deg. (1)θx- 80 88 -
VerticalθY+ 80 88 -
θY- 80 88 -
IDM-1104 User Manual 26
Chapter 7
OpticalC
haracteristics
Note1! Definition of Viewing Angle (θx, θy):
Viewing angles are measured by BM5A
Note2! Definition of Contrast Ratio (CR):
The contrast ratio can be calculated by the following expression.
Contrast Ratio (CR) = L255 / L0
L255: Luminance of gray level 255
L 0: Luminance of gray level 0
CR = CR (5), where CR (X) is corresponding to the Contrast Ratio of the point X at the figure in Note (7).
Note3! Definition of Response Time (TR, TF):
12 o’clock direction
θy+ = 90º
6 o’clock
θy- = 90º
θx− θx+
θy- θy+
x- y+
y- x+
Normal
θx = θy = 0º
θX+ = 90º
θX- = 90º
Optical
Response
100%
90%
10%
0%
Gray Level 255
Gray Level 0
Gray Level 255
TimeTF TR
27 IDM-1104 User Manual
Note4! Definition of Luminance of White (LC):
Measure the luminance of gray level 255 at center point and 5 points
LC = L (5), where L (X) is corresponding to the luminance of the point X at the figure in Note (7).
Note5! Definition of Cross Talk (CT):
CT = | YB – YA | / YA × 100 (%)
Where:
YA = Luminance of measured location without gray level 0 pattern (cd/
m2)
YB = Luminance of measured location with gray level 0 pattern (cd/m2)
Note6! Measurement Setup:
The LCD assembly should be stabilized at given temperature for 30 min-utes to avoid abrupt temperature change during measuring. In order to stabilize the luminance, the measurement should be executed after lighting Backlight for 30 minutes in a windless room.
Active Area
YA, U (D/2,W/8)
YA, R (7D/8,W/2)
YA, D (D/2,7W/8)
YA, L (D/8,W/2)
(0, 0)
(D,W)
Gray 128
Active Area
Gray 0
(D/4,W/4)
(3D/4,3W/4)
(0, 0)
YB, U (D/2,W/8)
YB, R (7D/8,W/2)
YB, D (D/2,7W/8)
YB, L (D/8,W/2)
(D,W)
Gray 128
Gray 0
CS-1000T
500 mm
LCD Module
LCD Panel
Center of the Screen
Light Shield Room
(Ambient Luminance < 2 lux)
USB2000
IDM-1104 User Manual 28
Chapter 7
OpticalC
haracteristics
Note7! Definition of White Variation (ᴽW):
Measure the luminance of gray level 255 at 5 points
ᴽW = Maximum [L (1), L (2), L (3), L (4), L (5)] / Minimum [L (1), L (2), L (3), L (4), L (5)]
D
W
Active Area
Ve
rtic
al L
ine
Horizontal Line
: Test Point
X=1 to 5
5
2 1
4 3
D/4 D/2 3D/4
W/4
W/2
3W/4
X
29 IDM-1104 User Manual
IDM-1104 User Manual 30
Chapter 8
8 Reliability Test Criteria8.1 Reliability Test Criteria
Test Item Test Condition Note
High Temperature Storage Test 70ºC, 240 hours
(1) (2)
Low Temperature Storage Test -20ºC, 240 hours
Thermal Shock Storage Test -20ºC, 0.5hour ←→ 70 ℃ , 0.5hour; 100cycles, 1hour/cycle
High Temperature Operation Test
70ºC, 240 hours
Low Temperature Operation Test
-20ºC, 240 hours
High Temperature & High HumidityOperation Test
60ºC, 90%RH, 240hours
Shock (Non-Operating) 200G, 2ms, half sine wave, 1 time for ± X, ± Y, ± Z. (3)
Vibration (Non-Operating)1.5G, 10 ~ 300 Hz, 10min/cycle, 3 cycles each X, Y, Z
(3)
Note1! There should be no condensation on the surface of panel during test.
Note2! Temperature of panel display surface area should be 70 ºC Max.
Note3! During testing vibration and shock, the fixture in holding the module has to be hard and rigid enough so that the module would not be twisted or bent by the fixture.
IDM-1104 User Manual 32
Chapter 9
9 Packaging9.1 Packing Method(1) Carton Packing suffered no failure in the following reliability tests.
Test Item Test Conditions Note
Vibration
ISTA STANDARDRandom, Frequency Range: 2 – 200 HzTop & Bottom: 30 minutes (+Z), 10 min (-Z), Right & Left: 10 minutes (X)Back & Forth 10 minutes (Y)
Non Opera-tion
Dropping Test 1 Angle, 3 Edge, 6 Face, 61 cmNon Opera-tion
IDM-1104 User Manual 34
Chapter 9
Packaging
35 IDM-1104 User Manual
www.advantech.comPlease verify specifications before quoting. This guide is intended for referencepurposes only.All product specifications are subject to change without notice.No part of this publication may be reproduced in any form or by any means,electronic, photocopying, recording or otherwise, without prior written permis-sion of the publisher.All brand and product names are trademarks or registered trademarks of theirrespective companies.© Advantech Co., Ltd. 2016