user manual iusb-9041wg

8/8/2019 User Manual IUSB-9041WG

http://slidepdf.com/reader/full/user-manual-iusb-9041wg 1/37

Industrial USB Server User’s Manual

IUSB-9041WG

Version 1.1

July 2009.

ORing Industrial Networking Corp.

4F., NO.3, Lane235, Baociao Rd.Sindian City,

Taipei County 23145 Taiwan, R.O.C.

Tel: + 886 2 2918 3036

Fax: + 886 2 2918 3084

Website : www.oring-networking.com

E-mail : [email protected]

http://www.oring-networking.com/

mailto:[email protected]

mailto:[email protected]

http://www.oring-networking.com/



Table of ContentGETTING TO KNOW YOUR DEVICE SERVER............................................................................................... 1

1.1 About the IUSB-9041WG USB Server ........................................................... ................................... 1

1.2 Software Features ................................... .............................................................. ........................... 1

1.3 Hardware Features ........................................................ .............................................................. ..... 2

HARDWARE INSTALLATION ....................................................................................................................... 3

2.1 Installing IUSB-9041WG on DIN-Rail ...... .............................................................. ........................... 3

2.1.1 Mount IUSB-9041WG on DIN-Rail ............................................................................................................ 3

2.2 Wall Mounting Installation ........................................................ ......................................................... 4

2.2.1 Mount IUSB-9041WG on the wall .............................................................................................................. 5

HARDWARE OVERVIEW ............................................................................................................................ 8

3.1 Front Panel ................................................................... ............................................................... ..... 8

3.2 Bottom panel ....................................................... ................................................................. ............. 9

CABLES ................................................................................................................................................10

4.1 Ethernet Cables ....................................................................... ....................................................... 10

MANAGEMENT INTERFACE .....................................................................................................................12 5.1 USBIP Admin ...................................................................................... ............................................ 12

5.1.1 Install USBIP Admin ................................................................................................................................. 12

5.1.2 Using USBIP Admin .................... ...................... ...................... ...................... ..................... ...................... . 13

5.1.2.1 Mount USB Device ........................................................................................................................ 13

5.1.2.2 Search the IUSB-9041WG ............................................................................................................. 15

5.1.2.3 Device Mapping ............................................................................................................................. 18

5.1.2.4 Printer Auto-Connect ..................................................................................................................... 19

5.1.3 Server Manager.......................................................................................................................................... 20

5.1.3.2 Manage USB server ..................................................................................................................... 20

5.2 Configuration by Web Browser .................................................................................................... ... 23

5.2.1 Connect to the Web page ........................................................................................................................... 24

5.2.2 Date / Time ................................................................................................................................................ 25

5.2.3 Network Setting .................... ...................... ...................... ...................... ...................... ..................... ........ 25

5.2.4 Status ......................................................................................................................................................... 28



IUSB-9041WG User’s Manual

5.2.5 Upgrade Firmware .................... ...................... ...................... ..................... ...................... ..................... ..... 28

5.2.6 Notification ................................................................................................................................................ 30

5.2.7 LOG Page ................... ..................... ...................... ...................... ...................... ...................... .................. 31

TECHNICAL SPECIFICATIONS ..................................................................................................................32



IUSB-9041 User’s Manual

1 ORing Industrial Networking Corp.

Getting to Know Your Device Server

1.1 About the IUSB-9041WG USB Server

As far as we know, we can easily share a printer over a network. But

why can't we share all the rest of your USB devices just as easily?

IUSB-9041 is a revolutionary solution from Oring. You can easily

access any USB device connected to IUSB-9041WG from your

computer via a LAN or the Internet as if it was physically plugged into

your own PC USB. The USB server supports wide variety of USB

devices and can connect 4 USB2.0 devices at the same time.

User can conveniently manage IUSB-9041WG by USBIP Admin or web via LAN interface. It is

easy for you to install and configure USB server over the network by USBIP Admin.

1.2 Software Features

Allows working with remote USB device as with local ones.

Supports wide variety of USB devices.

Compatible with bulk, interrupt and isochronous type USB devices.

Supports printing to USB printer from Wired Interface.

Supports Printer Auto Connect while sharing the printer to different Client PC's.

Supports USB device safe removal.

User-Friendly Application interface.





Hardware Installation

2.1 Installing IUSB-9041WG on DIN-RailEach IUSB-9041 has a DIN-Rail kit on rear panel. The DIN-Rail kit helps IUSB-9041 switch to

fix on the DIN-Rail. It is easy to install the IUSB-9041 on the DIN-Rail:

2.1.1 Mount IUSB-9041WG on DIN-RailStep 1: Slant the IUSB-9041 and mount the metal spring to DIN-Rail.

Figure 2-1

Metal Spring




ORing Industrial Networking Corp 4.

Step 2: Push the IUSB-9041WG toward the DIN-Rail until you heard a “click” sound.

Figure 2-2

2.2 Wall Mounting InstallationEach IUSB-9041WG has another installation method for users to fix the IUSB-9041WG. A

wall mount panel can be found in the package. The following steps show how to mount the

IUSB-9041WG on the wall.





2.2.1 Mount IUSB-9041WG on the wall

Step 1: Remove DIN-Rail kit.

Figure 2-3





Step 2: Use 6 screws that can be found in the package to combine the wall mount panel. Just like

the picture shows below:

Figure 2-4

The screws specification shows in the following two pictures. In order to prevent

IUSB-9041WG from any damage, the screws should not larger than the size that used in

IUSB-9041WG.

Pozidrive

Figure 2-5





Step 3: Mount the combined IUSB-9041WG on the wall.

Figure 2-6





Hardware Overview

3.1 Front Panel

Figure 3-1

1. Ready LED. Blinking when device is booting, and light on when device is ready to use.

2. LED for PWR1, PWR2 & PWR3. When the PWR is linked, the green led will be light on.

3. LED for USB. When USB device is connected, the green led will be light on.

4. LED for Ethernet ports status.

5. Reset Button. Press for 5 seconds for factory default.

6. LED for fault indicator. When fault occurred, this red LED will be light on.

7. USB port for USB device to connect.

1

2

3

4

5

6

7

8





8. 10/100Base-T(X) Ethernet port.

3.2 Bottom panel

The bottom panel components of IUSB-9041WG are shown as below:

1. Terminal block includes: PWR1 (12~48V DC).

2. Relay output (1A@24VDC).

3. Terminal block includes: PWR2 (12~48V DC).

4. Power Jack include: PWR2 (12 ~ 48V DC).

5. Frame ground.

Figure 3-2

1 32 4 5





Cables

4.1 Ethernet Cables

The IUSB-9041WG has standard Ethernet ports. According to the link type, the

IUSB-9041WG use CAT 3, 4, 5,5e UTP cables to connect to any other network device (PCs,

servers, switches, routers, or hubs). Please refer to the following table for cable

specifications.

Cable Type Max. Length Connector

10BASE-T Cat. 3, 4, 5 100-ohm UTP 100 m (328 ft) RJ-45

100BASE-TX Cat. 5 100-ohm UTP UTP 100 m (328 ft) RJ-45

Table 4-1 Cable Types and Specifications

100BASE-TX/10BASE-T Pin Assignments

With 100BASE-TX/10BASE-T cable, pins 1 and 2 are used for transmitting data, and pins 3

and 6 are used for receiving data.





Pin Number Assignment

1 TD+

2 TD-

3 RD+

4 Not used

5 Not used

6 RD-

7 Not used

8 Not used

Table 4-2 RJ-45 Pin Assignments

The IUSB-9041WG supports auto MDI/MDI-X operation. You can use a straight- through

cable to connect PC to IUSB-9041WG. The following table below shows the 10BASE-T/

100BASE-TX MDI and MDI-X port pin outs.

Pin Number MDI port MDI-X port

1 TD+(transmit) RD+(receive)

2 TD-(transmit) RD-(receive)

3 RD+(receive) TD+(transmit)

4 Not used Not used

5 Not used Not used

6 RD-(receive) TD-(transmit)

7 Not used Not used

8 Not used Not used

Table 4-2 MDI / MDI-X pins assignment

Note: “ + ” and “ - ” signs represent the polarity of the wires that make up each wire pair.





Management Interface

5.1 USBIP Admin

USBIP Admin is a powerful Windows utility for USB server. It supports server discovery, server

configuration and Device Mapping .it is easy for you to install and configure server over the

network.

5.1.1 Install USBIP Admin

Please run the setup program, Follow the instructions on screen to install the USB-Tool.exe.

After finishing Installing, Running USB-Tool.exe, it will be shown as below.

USBIP

Admin





5.1.2 Using USBIP Admin

5.1.2.1 Mount USB Device

In this section, you will learn how to use your USB devices via the USB Server.

Step 1 Connecting Your USB Device to the USB Server

Figure 5-1

Before using USB Server, connect your USB device to any of the USB port on the

USB Server.

Step 2 Mount your USB device to the USB server.

Right-click the USB device, choose “connect”, the USB device will be mounted to the

local PC, then you can access this device freely as if it was physically plugged into

your own PC USB

Plug in USB devices





Figure 5-2 Note : Any device is to be disconnected or unplugged only after proper closure of related Applications.

Connect Disconnect





5.1.2.2 Search the IUSB-9041WG

Step 1 Search servers over Network. You can scan all server or scan specify server.

The list will show all the USB server devices over the Network. (Default IP:

192.168.10.2)

Figure 5-3





It also allows user to search the device by enter the MAC of the

IUSB-9041WG.After the tool gets the device, go to the next step to set the IP

of IUSB-9041WG.

Figure 5-4





Step 3 After the device is set & updated, it will be added into the list.

Figure 5-5

Figure 5-6





5.1.2.3 Device Mapping

To start mapping/unmapping the device on IUSB-9041WG, please go to “Device

Mapping” and click on the “Start Mapping device” or “Stop Mapping Device”

Figure 5-7





5.1.2.4 Printer Auto-Connect

USBIP Admin Utility enables Printers be shared between multiple clients making it a

bidirectional Print Server.

In order to share the printer between multiple clients, user may need to connect the

printer at least once to install the driver for the Printer.

Once the printer is enumerated, disconnect the Printer form the Device Mapping

Window; Select the Printer Auto Connect button on the menu bar to open

the Printer Auto-Connect Window. This can also be done from “Device Mapping”

window.

Figure 5-8





Basic setting

You can set any name that you like for USB server. USB server Default Name is

“IUSB-9041WG”.

Figure 5-10

IP setting

You must assign a valid IP address for USB Server before attached in your network

environment. You can configure the Static IP manually or set DHCP mode to

automatically obtain an IP address from DHCP server. The Factory Default IP

address is “192.168.10.2”





Figure 5-10

Password

You can set up the password to prevent unauthorized access from your

server. Factory default is “admin”

Figure 5-11





Restore Factory Default

Right- click on the USB Server in the list and select the” Restore Factory

Defaults” function to Restore all the USB server configuration to Default

settings.

Figure 5-12

5.2 Configuration by Web Browser

Users can easily manage USB Server by Sever WEB Page. The web interface has a home

page and four configuration pages, include Home page, Network Page, Status Page, Upgrade

Firmware Page and LOG Page.





5.2.1 CONNECT TO THE WEB PAGE

Input the IP address of USB server with “https://192.168.10.2” in the URL of the browser,

then home page will be shown as below. The home page main displays the current network

settings, Server name, Firmware version and the USB server Feature.

Figure 5-13





5.2.2 DATE / TIME

Date and Time can be set from this page. By enabling the NTP allow the

device to get the date / time from NTP server when the IUSB-9041WG started

up.

Figure 5-14

5.2.3 NETWORK

SETTING

You must assign a valid IP address for USB Server before attached in your network

environment. You can configure the Static IP manually or set DHCP mode to

automatically obtain an IP address from DHCP server. The Factory Default IP

address is “192.168.10.2”





Figure 5-15

Wireless setting

Wireless Network type includes two modes: INFRA and ADHOC. The INFRA

type connects the network by wireless access point, but the ADHOC is formed

by the association of wireless and mobile devices capable of communicating

among themselves even when there is no networking INFRA structure

available.





Figure 5-16

The following table describes the labels in this screen.

Label Description

Network Type Type includes INFRA and ADHOC.

SSID

Service Set Identifier Default is the default setting. The SSID is a unique name that

identifies a network. All devices on a network must share the same SSID name in order to

communicate on the network.

ChannelAll devices on the network must be set to the same channel to communicate on the network.

You can select the Auto.

NO Encryption You can set no encryption mode, but this mode is insecurity and don’t suggest use.

WEP You can set four encryption 5characters (WEP64), 13 characters (WEP128), 10 digits(WEP64), 26digits (WEP128).

TKIP TKIP (Temporal Key Integrity Protocol) is a key management protocol.

AESAES (Advanced Encryption System) is a variable bit length symmetric digital encryption

algorithm.

Table 5-3 Wireless Network setting

*Simply unplug the RJ-45 to change into wireless connection





5.2.4 STATUS

The status page displays the current status of the USB devices attached.

The Device Status table shows the Vendor Id, Product Id, Product Name, and

Manufacturer name, USB Speed, client IP, client PC name, Duration.

Figure 5-17

5.2.5 UPGRADE FIRMWARE

You can upgrade Firmware by http ,click “Browse” and Choose the firmware path,

then click ”Http Upgrade” .





Figure 5-18





Important Note: It will take about 6 to 7 minutes to upgrade the Firmware. Please don’t power-off

the Power or remove the network cable during the Firmware Upgrade. The USB server will auto reboot

after the firmware grade is completed.

5.2.6 NOTIFICATION Specify the events that should be notified to the administrator. The events can be

alarmed by E-mail, system log or LED / Relay.

Figure 5-19





5.2.7 LOG PAGE This Page will show the Event Log Information in detail after Event Happen.

The Log table shows the time, Event, USB device, client IP, client PC, Name.

Figure 5-20





Technical Specifications

Network Interface

Ethernet 10/100Base-T(X)

Protocols IP, TCP, UDP, DHCP, BOOTP, ARP/RARP, DNS, SNMP, HTTP

WLAN Feature

Operating Mode Client mode

Antenna Connector Reverse SMA

Radio Frequency Type DSSS, OFDM

ModulationIEEE802.11b: CCK, DQPSK, DBPSK

IEEE802.11g: OFDM with BPSK, QPSK, 16QAM, 64QAM

Frequency Band

America/FCC: 2.412~2.462 GHz (11 channels)

Europe CE/ETSI: 2.412~2.472 GHz (13 channels)

Transmission RateIEEE802.11b: 1/ 2/ 5.5/ 11 Mbps

IEEE802.11g: 6/ 9/ 12/ 18/ 24/ 36/ 48/ 54 Mbps

Transmit Power IEEE802.11b/g: 16dBm

Encryption

Security

WEP: (64-bit ,128-bit key supported)

WPA/WPA2 :802.11i(WEP and AES encryption)

PSK (256-bit key pre-shared key supported) 802.1X and Radius

supported TKIP encryption

Wireless Security SSID broadcast disable

LED Indicators

LED Indicators

PWR1, PWR 2 , PWR 3

1) Green On: Power is on and functioning normally.

Ready

1) Green On: Device is ready to use.

USB Port LED:

1) Green On: USB device connected.





Fault Relay

1) Amber On: Fault Alarm

Power Requirements

Power InputPWR1, 2: 12 ~ 48VDC 3-pin in Terminal Block

PWR3: 12 ~ 48VDC in power jack

Reverse Polarity Protection Present at terminal block

Power Consumption 4 Watts MAX

Software Utility

Utility

USB-Tool for Windows NT/2000/XP/ 2003/VISTA/Windows

7(32/64 bit) which include

Device discovery

ConfigurationWeb HTTP, USB-Tool for Windows NT/2000/XP/VISTA/Windows

7(32/64 bit)

Environmental

Operating Temperature -10 to 60°C (14 to 140°F)

Operating Humidity 5% to 95%(Non-condensing)

Storage Temperature -40 to 85°C (-40 to 185°F)

Mechanical

Dimensions(W x D x H) 26mm(W)x95mm(D)x144mm(H)

Casing IP-30 protection

Regulatory Approvals

Shock IEC 60068-2-27

Free Fall IEC 60068-2-32

Vibration IEC 60068-2-6

EMI FCC Part 15, CISPR (EN55022) class A

EMS

EN61000-4-2 (ESD), EN61000-4-3 (RS)

EN61000-4-4 (EFT)

EN61000-4-5 (Surge)




ORing Industrial Networking Corp 34

EN61000-4-6 (CS)

Warranty 5 years

user manual iusb-9041wg

Documents