The uplink port is a gigabit ethernet port (GE1) which is located in the card called as ICM-A Card==============================================CONFIGURE A MANAGEMENT VLAN AND ATTACH THE UPLINK TO THIS VLANNote: here uplink interface is GE 1 and management vlan id is taken as 127Step 1:  Let us  create a vlan with vlan id : 127DSLAM#slot icmDSLAM(ICM-A)#vlanDSLAM(ICM-A/vlan)# vid 127 name inbandStep 2:  Le us map this vlan 127 to the uplinkDSLAM#slot icmDSLAM(ICM-A)#vlanDSLAM(ICM-A/Vlan)#interface ge 1 vid 127 tag ==========================================CONFIGURE AN IP ADDRESS FOR THIS MANAGEMENT VLANDSLAM#accessDSLAM(access)#DSLAM(access)#in-band vid 127 address 192.168.1.1 netmask 255.255.255.252==================================================CONFIGURE ROUTING TABLE FOR THIS DSLAMStep 4: Let us create the routing tableDSLAM#ip route 0.0.0.0 netmask 0.0.0.0 gateway 192.168.1.2 interface inband=============================================CONFIGURATION FOR REDUNDANT CONTROL CARD We are now doing the configuration on the active ICM card. This configuration should be automaticallytransferred to the standby ICM card which is redunant card. DSLAM#redundancy===========================================SAVE THE CONFIGURATIONDSLAM#save config

=====================================================CONFIGURATION OF USER PORTSStep 1: Create vlan for each user port in icm cardCommand:DSLAM#slot icmDSLAM(ICM-A)#VlanDSLAM(ICM-A/Vlan)# vid 128 name vlan128 (like this do it for 128 to 559)

Step 2: Create such vlan in each ADSL Line Card (each  line card contains 48 VLANs)ADSL card in slot1 has 128 to 175 vlans, slot2 has 176 to 223 vlans128-175 in slot 1,176-223 in slot 2DSLAM#slot 1DSLAM(IPADSL8A-1)#vlanDSLAM(IPADSL8A-1/VLAN)# vid 128 name vlan128 (like this 128 to 175 for slot 1...upto slot9)DSLAM(IPADSL8A-1/VLAN)# vid 175 name vlan 175Step 3:  Let us map these ports to ICM card vlansMap the ICM card vlans to Internal ports in tag mode.Command:DSLAM#slot icmDSLAM(ICM-A)#vlanDSLAM(ICM-A/Vlan)#interface internal 1 vid 128 tag ( do it for 128 to 175 of slot1)DSLAM(ICM-A/Vlan)#interface internal 2 vid 176 tag ( do it for 176 to 223 of slot2)(do it upto 559)===================================================== CONFIGURE EACH ATM INTERFACE

DSLAM#slot 1 ( like this, there are 9 slots)DSLAM(IPADSL8A-1/PORT)#port

DSLAM(IPADSL8A-1/PORT)#interface atm 1:0.35 qos ubr encapsulation llcbridge(like this,do it for 1 to 48 ports)==========================================================CONFIGURING VLAN TO EACH PORT

DSLAM#slot 1DSLAM(IPADSL8A-1)#vlanDSLAM(IPADSL8A-1/VLAN)#interface atm 1:0.35 vid 128 untagNote:Like this, configure for 9 slots x  48 portsvlan 128 is for port 1 of slot 1,vlan 129 is  for port 2 of slot1vlan 175 is port 48 of slot1, vlan 559 is port 48 of slot 9

===============================================CREATE PROFILE FOR CUSTOMERSDSLAM#profile my-spectrum-profile spectrum ln-std 32 (this is spectrum profile)DSLAM#profile ln-adsl line dn0-max-rate 2048(this is service profile)DSLAM#profile ln-adsl  my-line-profile dn0-delay 1 (this is line profile)DSLAM#profile adsl my-adsl-profile  my-line-profile line sp-adsl spectrumNow attach this profile to the line ports.DSLAM#slot 1DSLAM(IPADSL8A-1)#portDSLAM(IPADSL8A-1/PORT)#disable dsl 1-48 (disable before attaching)DSLAM#slot 1DSLAM(IPADSL8A-1)#portDSLAM(IPADSL8A-1/PORT)#profile  my-line-profile port dsl 1(like this,do it for all the ports)DSLAM(IPADSL8A-1/PORT)#enable dsl 1-48 (now enable all the ports)==========================================ADD THE TRUNK PORT TO ALL VLANSDSLAM#slot icmDSLAM(ICM-A)#vlanDSLAM(ICM-A/Vlan)#interface ge 1 vid 128 tag (like this, do it for 128 to 559)===============================================