validation boot camp 3
TRANSCRIPT
![Page 1: Validation boot camp 3](https://reader034.vdocument.in/reader034/viewer/2022042613/554b8568b4c9056d5f8b4f26/html5/thumbnails/1.jpg)
1
VALIDATION BOOT CAMP #3
LIFECYCLE APPROACH TO PHARMACEUTICAL VALIDATION –
PRINCIPLES, IMPLEMENTATION, AND PRACTICE
LIFECYCLE APPROACH TO CLEANING VALIDATION
Paul L. Pluta, PhD
![Page 2: Validation boot camp 3](https://reader034.vdocument.in/reader034/viewer/2022042613/554b8568b4c9056d5f8b4f26/html5/thumbnails/2.jpg)
MANUAL CLEANING -- Do you really know what is happening?
Q to operator: “Why is there so much foam in the tub?” A: “I put in extra soap because the equipment was really dirty.”
Q to operator: “Why is there powder on the (clean) equipment?” A: “No problem -- We’ll get the residue when we set up.”
Q to operator: “Why don’t you follow the cleaning procedure?” A: “The cleaning procedure really doesn’t work.”
ABOVE NOT ACCEPTABLE – TRAINING NEEDED
2
![Page 3: Validation boot camp 3](https://reader034.vdocument.in/reader034/viewer/2022042613/554b8568b4c9056d5f8b4f26/html5/thumbnails/3.jpg)
MANUAL CLEANING -- Do you really know what is happening?
Q to operator: “Why is there powder on the clean equipment?” A: “It’s clean enough.” Q to QA (equipment inspection person): “Did you approve that the equipment
is clean?” A: “It’s clean enough.” Q to management: “Do you know that your equipment is not clean?” A: “It’s clean enough.”
Q to operator: “You cleaned the gasket with pure soap – this is not the procedure? Also it is dangerous – these are corrosive chemicals.”
A: “That is the only way to get it clean.” Q: “So why don’t you tell someone to change the procedure?” A: “We don’t have time.”
ABOVE NOT ACCEPTABLE – TRAINING NEEDED
3
![Page 4: Validation boot camp 3](https://reader034.vdocument.in/reader034/viewer/2022042613/554b8568b4c9056d5f8b4f26/html5/thumbnails/4.jpg)
MANUAL CLEANING -- Do you really know what is happening?
Q to management: “Did you finish cleaning the equipment? We are here to swab for cleaning validation.”
A (very proudly): “We cleaned the equipment three times so that we won’t have any problems.”
Q to validation person: “Did you know that the manufacturing people
always clean the equipment multiple times before it is swabbed?” A: “Sure, we knew. Q: “Why didn’t you stop this?” A: “These people are our friends. We have to work with these
people.”
ABOVE NOT ACCEPTABLE – TRAINING NEEDED
4
![Page 5: Validation boot camp 3](https://reader034.vdocument.in/reader034/viewer/2022042613/554b8568b4c9056d5f8b4f26/html5/thumbnails/5.jpg)
OUTLINE Lifecycle Approach Applied to Cleaning Validation Stage 1 Activities • Cleaning Method Development • Analytical Method Development • Site equipment Stage 2 Activities • Cleaning documentation • Validation conformance lots Stage 3 Activities • Maintaining Validation • Change Control • Management review
5
![Page 6: Validation boot camp 3](https://reader034.vdocument.in/reader034/viewer/2022042613/554b8568b4c9056d5f8b4f26/html5/thumbnails/6.jpg)
OBJECTIVES 1. Application of lifecycle approach to cleaning
validation 2. Cleaning lifecycle stage details
• Process development and understanding • Process qualification • Maintaining the validated state
3. Cleaning validation problems • Global experiences
6
![Page 7: Validation boot camp 3](https://reader034.vdocument.in/reader034/viewer/2022042613/554b8568b4c9056d5f8b4f26/html5/thumbnails/7.jpg)
Lifecycle Approach to Cleaning Validation – Value? Does this make sense?
• Cleaning is a process
• Validation lifecycle concepts being applied to equipment, facilities, utilities, computers, etc., by validation and technical experts
• Who can argue with understanding, performing, and maintaining the validated state?
• Consistent with QbD and ICH approaches
• Lifecycle approach (i.e., understanding, performing, maintaining) vs. traditional approach – Which would you rather present to an auditor?
7
![Page 8: Validation boot camp 3](https://reader034.vdocument.in/reader034/viewer/2022042613/554b8568b4c9056d5f8b4f26/html5/thumbnails/8.jpg)
WHAT IS THE CLEANING PROCESS? Cleaning Process Performance Qualification (PPQ)
Automated CIP System
Process steps Qualification 1. Residue on equipment Equipment 2. Water procedure Purified Water 3. Cleaning agent procedure Computer / software 4. Water procedure Compressed air 5. Purified Water procedure Conductivity analysis 6. Dry TOC analysis
Equipment is clean -- Process is validated
Process parameters à Quality attributes
8
![Page 9: Validation boot camp 3](https://reader034.vdocument.in/reader034/viewer/2022042613/554b8568b4c9056d5f8b4f26/html5/thumbnails/9.jpg)
WHAT IS THE CLEANING PROCESS? Cleaning Process Performance Qualification (PPQ)
Manual Cleaning Process steps Qualification 1. Residue on equipment Personnel 2. Water rinse Purified Water 3. Scrub with cleaning agent Compressed air 4. Water rinse 5. Scrub 6. Water rinse 7. Purified Water rinse 8. Dry
Equipment is clean -- Process is validated
Process parameters à Quality attributes 9
![Page 10: Validation boot camp 3](https://reader034.vdocument.in/reader034/viewer/2022042613/554b8568b4c9056d5f8b4f26/html5/thumbnails/10.jpg)
CLEANING VALIDATION OVERVIEW 1990s àpresent
1. Defined cleaning procedure (SOP) – basis? 2. Product A batch does not contaminate subsequent
Product B batch 3. Acceptance limit calculated 4. Assume uniform contamination of all equipment 5. Three conformance lots = Validated cleaning procedure 6. Validated analytical method (original API) 7. Worst-case matrix approach
One-time event
10
![Page 11: Validation boot camp 3](https://reader034.vdocument.in/reader034/viewer/2022042613/554b8568b4c9056d5f8b4f26/html5/thumbnails/11.jpg)
FDA PROCESS VALIDATION GUIDANCE LIFECYCLE APPROACH TRANSITION
APPPLICATION TO CLEANING VALIDATION
Pre Lifecycle
Cleaning development (?) à PQ à change control ________________________
Lifecycle Approach
Development à PQ à Maintenance
EXPANDED SCOPE OF VALIDATION INCREASED SPECIFIC STAGE REQUIREMENTS
11
![Page 12: Validation boot camp 3](https://reader034.vdocument.in/reader034/viewer/2022042613/554b8568b4c9056d5f8b4f26/html5/thumbnails/12.jpg)
LIFECYCLE APPROACH TO CLEANING VALIDATION
Scientific and technical approach Design and development
– Residue + cleaning agent + cleaning procedure à Clean equipment
Performance demonstration Monitoring and maintenance Rationale, responsibility, and accountability Future process improvements
Not the following: – Standard site method (no basis or rationale) – Personnel driven (no control) – “Do whatever it takes” (high variation) – SOP (no accountability) – Validation (?) – One-time event.
12
![Page 13: Validation boot camp 3](https://reader034.vdocument.in/reader034/viewer/2022042613/554b8568b4c9056d5f8b4f26/html5/thumbnails/13.jpg)
STAGE 1, PROCESS DESIGN (PROCESS UNDERSTANDING) APPLICATION TO CLEANING
FDA Guidance Topics 1. Building and capturing process knowledge and understanding. 2. Establishing a strategy for process control.
Application to Cleaning Understand residue chemistry (solubility, stability) Determine cleaning agent based on residue chemistry Determine cleaning process • Identify sources of variability • Establish methods to control variability
– Process Analytical Technology Rational analytical method and supporting work Characterization of equipment to be cleaned and supporting work Trained sampling personnel
DOCUMENT ALL OF THE ABOVE
13
![Page 14: Validation boot camp 3](https://reader034.vdocument.in/reader034/viewer/2022042613/554b8568b4c9056d5f8b4f26/html5/thumbnails/14.jpg)
DEVELOPMENT (STAGE 1) CLEANING PROCESS DEVELOPMENT
• Physical and chemical properties of the residue is basis for cleaning process
• Considerations for determination of most difficult-to-clean residue • Residue solubility and stability in determining worst-case soils • Residue chemistry critical for analytical method • Cleaning agent chemistry consistent with residue chemistry • Cleaning process chemistry and engineering and consistent with
residue and cleaning agent.
RESIDUE CHEMISTRY – BASIS FOR CLEANING PROGRAM – BASIS FOR ANALYICAL METHOD
14
![Page 15: Validation boot camp 3](https://reader034.vdocument.in/reader034/viewer/2022042613/554b8568b4c9056d5f8b4f26/html5/thumbnails/15.jpg)
RESIDUE PROPERTIES -- BASIS FOR CLEANING PROCESS Case study: Antibiotic suspension containing insoluble API (base)
Original cleaning method: Water, PurW, dry • No documented cleaning validation for many years • Unknown peaks on original cleaning validation attempts • API insoluble
Second method: Alkaline soap wash, water, PurW, dry • Unknown peaks again • API insoluble
Final method: Acid wash, alkaline soap wash, water, PurW, dry • No residues • Unknown peaks determined to be degradants and flavors. • API dissolves (acid-base neutralization)
Consider active drug and other residue chemistry in development of cleaning process
15
![Page 16: Validation boot camp 3](https://reader034.vdocument.in/reader034/viewer/2022042613/554b8568b4c9056d5f8b4f26/html5/thumbnails/16.jpg)
DETERMINATION OF MOST DIFFICULT TO CLEAN RESIDUE
BASIS FOR CLEANING PROGRAM
Water solubility – USP Tables • Is this adequate? NO! pH effect – API with ionizable groups? Solubility in cleaning agent? • Determine solubility at range pH 1-12 • Understand solubility at pH of cleaning liquid • Understand solubility in cleaning agent liquid
16
![Page 17: Validation boot camp 3](https://reader034.vdocument.in/reader034/viewer/2022042613/554b8568b4c9056d5f8b4f26/html5/thumbnails/17.jpg)
pH SOLUBILITY PROFILE, pH 1-12
Solubility mg/ml
Drug A Drug B
pH 1 7 12
17
![Page 18: Validation boot camp 3](https://reader034.vdocument.in/reader034/viewer/2022042613/554b8568b4c9056d5f8b4f26/html5/thumbnails/18.jpg)
RESIDUE SOLUBILITY AND STABILITY FOR DETERMINING WORST-CASE SOILS
Solubility considerations • Hydrophilic and hydrophobic molecules • Ionization – Effect of pH • Effect of temperature • Surface active molecules • Liquid and semisolid product vehicle polarity
Stability considerations • Hydrolysis, oxidation, photolysis, physical changes
What residue is really present? Consider chemistry of residues
18
![Page 19: Validation boot camp 3](https://reader034.vdocument.in/reader034/viewer/2022042613/554b8568b4c9056d5f8b4f26/html5/thumbnails/19.jpg)
CLEANING MATRIX Determine Worst-Case Soil
SOLUBILITY (mg / ml) pH 1 Water pH 12 Alkaline
Cleaning Agent Drug A 25 25 25 25
Drug B 15 15 15 15
Drug C 5 5 150 250
Drug D 150 10 10 50
Drug E 125 10 100 250
Consider acid cleaning agent for drugs D and E
19
![Page 20: Validation boot camp 3](https://reader034.vdocument.in/reader034/viewer/2022042613/554b8568b4c9056d5f8b4f26/html5/thumbnails/20.jpg)
WORST CASE CLEANING
Determination of worst-case cleaning based on API toxicity, worst-case dose, etc. – Standard calculation
Cleaning procedure may be based on excipients having greatest effect on cleaning – Hydrophilic polymers – Dyes – Hydrophobic vehicles
20
![Page 21: Validation boot camp 3](https://reader034.vdocument.in/reader034/viewer/2022042613/554b8568b4c9056d5f8b4f26/html5/thumbnails/21.jpg)
BIOTECH CLEANING CHEMISTRY -- API Protein molecules degrade in alkaline conditions Degradation rate is milder in acidic conditions Degradation rate increases with temperature API residues typically consist of protein fragments and
aggregates Analytical method: Non-specific analysis Reference: Kendrick, Canhuto, and Kreuze. Analysis of
Degradation Products of Biopharmaceutical API Caused by Cleaning Agents and Temperature. Journal of Validation Technology, V15, #3, Summer 2009.
21
![Page 22: Validation boot camp 3](https://reader034.vdocument.in/reader034/viewer/2022042613/554b8568b4c9056d5f8b4f26/html5/thumbnails/22.jpg)
BIOTECH CLEANING CHEMISTRY – GROWTH MEDIUM
Medium Composition • Acids or bases • Monovalent salts • Polyvalent salts • Amino acids • Proteins (polypeptides) • Carbohydrates • Aqueous soluble organics • Non-aqueous soluble organics
Consider medium composition at end of cycle.
Reference: Azadan and Canhoto. A Scientific Approach to the Selection of Cleaning Validation Worst-Case Soils for Biopharmaceutical manufacturing. Cleaning and Cleaning Validation, Volume 1. 2011.
22
![Page 23: Validation boot camp 3](https://reader034.vdocument.in/reader034/viewer/2022042613/554b8568b4c9056d5f8b4f26/html5/thumbnails/23.jpg)
CLEANING CHEMISTRY MECHANISMS
• Wetting • Emulsification • Dispersion • Solubility • Chelation • Oxidation • Hydrolysis
23
![Page 24: Validation boot camp 3](https://reader034.vdocument.in/reader034/viewer/2022042613/554b8568b4c9056d5f8b4f26/html5/thumbnails/24.jpg)
CLEANING AGENT OPTIONS
• Water • Commodity alkalis and acids • Organic solvents • Surfactants
– Anionic – Cationic – Amphoteric – Nonionic
• Formulated detergents
24
![Page 25: Validation boot camp 3](https://reader034.vdocument.in/reader034/viewer/2022042613/554b8568b4c9056d5f8b4f26/html5/thumbnails/25.jpg)
COMPONENTS OF FORMULATED DETERGENTS
• Surfactants • Alkalis • Acids • Sequestrants / chelants • Dispersants / anti-redeposition agents • Corrosion inhibitors • Oxidizing agents • Enzymes • Buffers / builders • Preservatives
MUST HAVE CONTROL OF CLEANING AGENT HAVE CONFIDENTIALITY AGREEMENT WITH SUPPLIER
25
![Page 26: Validation boot camp 3](https://reader034.vdocument.in/reader034/viewer/2022042613/554b8568b4c9056d5f8b4f26/html5/thumbnails/26.jpg)
CLEANING ENGINEERING Factors affecting cleaning • Soil residue
– Soil levels, soil condition, hold times, soil mixing, water quality and residue,
• Cleaner and parameters (TACT) – Time, Action, Concentration, Temperature – Others
• Surface and equipment design
26
![Page 27: Validation boot camp 3](https://reader034.vdocument.in/reader034/viewer/2022042613/554b8568b4c9056d5f8b4f26/html5/thumbnails/27.jpg)
CLEANING PROCESS SOURCES OF VARIATION
• Cleaning agent preparation – must be exact • Automated cleaning vs. manual cleaning • Manual cleaning process variation • Human physical strength variation • “Cleaning” between same-product batches in
campaign – residue level build-up • Campaign length – residue level build-up • Time to initiate cleaning (dirty hold time) • Residue chemical and physical changes
27
![Page 28: Validation boot camp 3](https://reader034.vdocument.in/reader034/viewer/2022042613/554b8568b4c9056d5f8b4f26/html5/thumbnails/28.jpg)
EQUIPMENT TO BE CLEANED Cleaning-related qualification • Product-contact materials • Compatibility with cleaning agents • Surface areas – need for residue calculations • Equipment equivalence • Most-difficult-to-clean locations on equipment -- Highest
risk locations for sampling • Non-uniform contamination equipment • Non-uniform contamination sampling locations • Sampling methods (swab / rinse)
Part of IQ/OQ/PQ for manufacturing equipment
28
![Page 29: Validation boot camp 3](https://reader034.vdocument.in/reader034/viewer/2022042613/554b8568b4c9056d5f8b4f26/html5/thumbnails/29.jpg)
PROCEDURE TO DETERMINE SAMPLING LOCATIONS
Specific documented procedure recommended • Equipment technical evaluation • Observation of equipment after processing • Equipment disassembly review • Cleaning procedure review • Equipment evaluation review • Operator interviews
SOP describing above Documentation of above for equipment sampling
29
![Page 30: Validation boot camp 3](https://reader034.vdocument.in/reader034/viewer/2022042613/554b8568b4c9056d5f8b4f26/html5/thumbnails/30.jpg)
TIME TO INITIATE CLEANING “DIRTY HOLD TIME”
1. Make Product A 2. Clean 3. Make Product B How long between end of #1 and start #2? Is residue same? Does residue change? What can happen to the residue? • Wet and dry processes
• Chemical changes (hydrolysis, oxidation, etc.)
• Physical changes
30
![Page 31: Validation boot camp 3](https://reader034.vdocument.in/reader034/viewer/2022042613/554b8568b4c9056d5f8b4f26/html5/thumbnails/31.jpg)
CAMPAIGN LENGTH
How many lots in manufacturing campaign before cleaning must be done?
What about “cleaning” between batches? • Equipment should be visually clean • Terminology: “Between lot procedure” • How much residue “build-up?”
DO NOT IDENTIFY AS “BETWEEN LOT CLEANING”
31
![Page 32: Validation boot camp 3](https://reader034.vdocument.in/reader034/viewer/2022042613/554b8568b4c9056d5f8b4f26/html5/thumbnails/32.jpg)
MANUAL CLEANING
• Manual cleaning procedures should be monitored and maintained with increased scrutiny compared to non-manual procedures
• More frequent training of cleaning personnel • Increased supervision • Periodic (annual?) revalidation batches
Manual cleaning is high risk
32
![Page 33: Validation boot camp 3](https://reader034.vdocument.in/reader034/viewer/2022042613/554b8568b4c9056d5f8b4f26/html5/thumbnails/33.jpg)
ANALYTICAL METHOD DEVELOPMENT
Early stage 1 (development) analysis – validation not required but must be sound
Validated method when used for Stage 2 cleaning validation and post-validation testing (change control)
All methods and data (including stage 1) subject to
regulatory audit
33
![Page 34: Validation boot camp 3](https://reader034.vdocument.in/reader034/viewer/2022042613/554b8568b4c9056d5f8b4f26/html5/thumbnails/34.jpg)
ANALYTICAL METHOD DEVELOPMENT
Analytical method must measure actual residue – what residue is actually present on equipment surfaces?
• Small molecules – API – API degraded – specific or non-specific method
• Biotech molecules – API degraded – non-specific method
UNDERSTAND RESIDUE CHEMISTRY
34
![Page 35: Validation boot camp 3](https://reader034.vdocument.in/reader034/viewer/2022042613/554b8568b4c9056d5f8b4f26/html5/thumbnails/35.jpg)
ANALYTICAL METHOD DEVELOPMENT
Cleaning agent residue • Analytical method to determine residual cleaning
agent. • Information from cleaning agent vendor
35
![Page 36: Validation boot camp 3](https://reader034.vdocument.in/reader034/viewer/2022042613/554b8568b4c9056d5f8b4f26/html5/thumbnails/36.jpg)
ANALYTICAL METHOD DEVELOPMENT Recovery studies Can sampling procedure adequately recover residue
from equipment surfaces? • Product contact materials • High % of total surface area • Obtain representative coupons from equipment
fabricators • High (e.g., >80%) acceptance criteria • Factor may be used in calculation
– Multiple approaches – Factor every calculation?
All sampled surfaces must have recovery data
36
![Page 37: Validation boot camp 3](https://reader034.vdocument.in/reader034/viewer/2022042613/554b8568b4c9056d5f8b4f26/html5/thumbnails/37.jpg)
SAMPLING Sampling methods • Sampling (swab) critical activity • Training program • Trained sampling personnel
– Demonstrated acceptable performance
• Documented training and retraining • Worst case compounds / procedures in training
– Volatile solvents (importance of rapid technique)
• Worst case sampling equipment – Extension poles
• Retraining considerations – Who does sampling? Personnel skills
37
![Page 38: Validation boot camp 3](https://reader034.vdocument.in/reader034/viewer/2022042613/554b8568b4c9056d5f8b4f26/html5/thumbnails/38.jpg)
SAMPLING TRAINING
Sampling is extremely critical to cleaning validation program
Inadequate sampling = false negative – Insufficient pressure on surface – Swab solvent evaporation – Insufficient area sampled
Auditors routinely ask for sampling program training methods and training records
38
![Page 39: Validation boot camp 3](https://reader034.vdocument.in/reader034/viewer/2022042613/554b8568b4c9056d5f8b4f26/html5/thumbnails/39.jpg)
STAGE 2, PROCESS QUALIFICATION – (VALIDATION PERFORMANCE)
APPLICATION TO CLEANING 1. Design of a facility and qualification of utilities and equipment 2. Process performance qualification 3. PPQ protocol 4. PPQ protocol execution and report
Qualification of equipment, utilities, facilities • Cleaning equipment (CIP) Process Performance Qualification (PPQ) – commercial scale Conclusion that process consistently produces clean equipment Conformance batches • All support systems, documents, training, personnel, etc. in place • Target / nominal operating parameters within design space • Additional testing (swab / rinse) • Decision to “release cleaning process” for routine commercial use • Post validation monitoring plan – Based on risk
– Drug residue properties – Manual or CIP
39
![Page 40: Validation boot camp 3](https://reader034.vdocument.in/reader034/viewer/2022042613/554b8568b4c9056d5f8b4f26/html5/thumbnails/40.jpg)
CLEANING EQUIPMENT
CIP system must be qualified (IQ/OQ/PQ or ASTM E2500)
Riboflavin (or other) coverage testing Temperature controls Flow rates, etc. PAT inline systems
– Drug disappearance – spectrophotometry, other methods – Cleaning agent rinse -- conductivity
40
![Page 41: Validation boot camp 3](https://reader034.vdocument.in/reader034/viewer/2022042613/554b8568b4c9056d5f8b4f26/html5/thumbnails/41.jpg)
CLEANING PROCEDURE DOCUMENTATION (Cleaning Batch Record)
SOP • Fill tank half full • Add half scoop of soap • Scrub as needed • Rinse until clean • Re-scrub and re-rinse if needed
CLEANING PROCEDURE RECORD • Fill tank with 500 L water. Sign/date __________ • Add 20.0 kg cleaning agent. Sign/date __________ • Disassemble Part A. Steps 1,2,3,4,5 • Scrub for 20 minutes. Sign/date __________ • Disassemble Part B. Steps 1,2,3,4,5 • Soak Part B in cleaning liquid for 10 minutes. Sign/date __________ • Rinse Part A and Part B with 50 L water. Sign/date __________ • Rinse with 50 L Purified Water. Sign/date __________ • Dry with compressed air
41
![Page 42: Validation boot camp 3](https://reader034.vdocument.in/reader034/viewer/2022042613/554b8568b4c9056d5f8b4f26/html5/thumbnails/42.jpg)
CLEANING PROCEDURE RECORD • Fill tank with 500 L water. Sign/date __________ • Add 20.0 kg cleaning agent. Sign/date __________ • Disassemble Part A. Steps 1,2,3,4,5 • Scrub for 20 minutes. Sign/date __________ • Disassemble Part B. Steps 1,2,3,4,5 • Soak Part B in cleaning liquid for 10 minutes. Sign/date __________ • Rinse Part A and Part B with 50 L water. Sign/date __________ • Rinse with 50 L Purified Water. Sign/date __________ • Dry with compressed air
KEY POINTS Exact concentration of cleaning agent liquid Signature on quantitative steps Grouping non-quantitative steps (e.g., disassembly)
42
![Page 43: Validation boot camp 3](https://reader034.vdocument.in/reader034/viewer/2022042613/554b8568b4c9056d5f8b4f26/html5/thumbnails/43.jpg)
VALIDATION REQUEST / PLAN Initiates cleaning validation • New cleaning validation or change control process
improvements • Strategy and approach • Scientific and technical basis • Specify required protocols and other work to accomplish
validation • Risk-based • References: Stage 1 Design / development reports
43
![Page 44: Validation boot camp 3](https://reader034.vdocument.in/reader034/viewer/2022042613/554b8568b4c9056d5f8b4f26/html5/thumbnails/44.jpg)
VALIDATION PROTOCOL
Cleaning validation protocols and other work as specified in Validation Plan – Risk based
Include sampling pages indicating worst case sampling locations.
Specify acceptance criteria
44
![Page 45: Validation boot camp 3](https://reader034.vdocument.in/reader034/viewer/2022042613/554b8568b4c9056d5f8b4f26/html5/thumbnails/45.jpg)
VALIDATION RESULTS / REPORT
Test results as required in validation protocol. • Discussion. Consistency with Stage 1
development work. • Clear statement the cleaning process is (or is
not) validated. • Recommendations for Stage 3 monitoring and
maintenance. – Additional limited testing based on data and risk – Routine monitoring based on risk
45
![Page 46: Validation boot camp 3](https://reader034.vdocument.in/reader034/viewer/2022042613/554b8568b4c9056d5f8b4f26/html5/thumbnails/46.jpg)
46
STAGE 3, CONTINUED PROCESS VERIFICATION (VALIDATION MONITORING AND MAINTENANCE)
APPLICATION TO CLEANING Activities to assure process remains in validated state Change control -- evaluate impact of change and validate (test) as
necessary Trend and assess data
– PAT rinse times – Conductivity data
Study OOS and OOT (Out of Trend) data Improve process Improve control to detect and reduce variability Cleaning non-conformances and deviations Re-validation – definition: Actual batch or “paper” • Is re-testing necessary? • When should re-testing be considered? Periodic Management Review • Documentation reviewed by management • Documented review
![Page 47: Validation boot camp 3](https://reader034.vdocument.in/reader034/viewer/2022042613/554b8568b4c9056d5f8b4f26/html5/thumbnails/47.jpg)
POST-VALIDATION MONITORING AND MAINTENANCE
1. Stage 2 specific requirements – Additional testing based on actual data – Ex: One location has high (acceptable result)
2. Routine monitoring and maintenance – Risk based
3. Change control program
CHANGE CONTROL MOST IMPORTANT AND DIFFICULT TO ADMINISTER
PERSONNEL MUST RECOGNIZE “CHANGE” 47
![Page 48: Validation boot camp 3](https://reader034.vdocument.in/reader034/viewer/2022042613/554b8568b4c9056d5f8b4f26/html5/thumbnails/48.jpg)
POST-VALIDATION MONITORING AND MAINTENANCE
Residue toxicity risk • Residue that can be visually seen
– Room lighting must be adequate – Provide additional lighting if necessary
• Residue that cannot be visually seen – Swab after each batch?
CONSIDER PATIENT RISK AND COMPANY RISK
48
![Page 49: Validation boot camp 3](https://reader034.vdocument.in/reader034/viewer/2022042613/554b8568b4c9056d5f8b4f26/html5/thumbnails/49.jpg)
CHANGE CONTROL
• All associated personnel must be aware of change control
• Change control system developed • Process improvements expected based on
ongoing experience • Process improvements should be evaluated by
technical people (i.e., Stage 1) • Stage 2 PPQ conducted when appropriate
based on Stage 1 technical evaluation.
49
![Page 50: Validation boot camp 3](https://reader034.vdocument.in/reader034/viewer/2022042613/554b8568b4c9056d5f8b4f26/html5/thumbnails/50.jpg)
POST-VALIDATION MONITORING
Periodic review of cleaning performance • Deviations • Non-conformances (dirty equipment) • Re-cleaning • Change control • Other monitoring (CIP data) • Product APR data • Statistical Process Control data treatment • Management review -- documented
50
![Page 51: Validation boot camp 3](https://reader034.vdocument.in/reader034/viewer/2022042613/554b8568b4c9056d5f8b4f26/html5/thumbnails/51.jpg)
CLEANING DOCUMENTATION • High level documents • Specific cleaning validation documents
– Design/Development, performance, monitoring/maintenance
• Specific cleaning validation support documents (equipment qualifications)
• Cleaning validation approach documents (Worst case matrix, calculations, sampling locations, etc.)
• Production documents (Cleaning Procedure Records) – Production cleaning policies
• Management review documents • Associated documents
– Personnel training in direct and associated areas – HR records
51
![Page 52: Validation boot camp 3](https://reader034.vdocument.in/reader034/viewer/2022042613/554b8568b4c9056d5f8b4f26/html5/thumbnails/52.jpg)
CLEANING DOCUMENTATION High level documents • Corporate policy • VMP (Cleaning VMP) Stage 1 documents • Cleaning process development report • Analytical method development report • Supporting equipment documents (materials, surface areas, equivalent equipment,
sampling, etc.) Stage 2 documents • Validation PPQ request, protocol, results • Cleaning equipment qualification • Cleaning procedure record Stage 3 documents • Change control documents • Process monitoring • Management review
CONSISTENT LIFECYCLE STRATEGY AND APPROACH
52
![Page 53: Validation boot camp 3](https://reader034.vdocument.in/reader034/viewer/2022042613/554b8568b4c9056d5f8b4f26/html5/thumbnails/53.jpg)
SUMMARY STAGE 1 -- DESIGN AND DEVELOPMENT
INCLUDING COMMON PROBLEMS
Understanding cleaning process • Residue properties
– Residue degradation • Rational cleaning process based on residue • Scientific and technical cleaning matrix Understand and control sources of variation • Dirty hold time • Campaigns Rational analytical method based on residue properties Equipment to be cleaned characterized • Worst case sampling
53
![Page 54: Validation boot camp 3](https://reader034.vdocument.in/reader034/viewer/2022042613/554b8568b4c9056d5f8b4f26/html5/thumbnails/54.jpg)
SUMMARY – EQUIPMENT TO BE CLEANED INCLUDING COMMON PROBLEMS
• Equipment characterization • Residue calculations • Materials of product contact • Surface areas • Worst-case areas for sampling based on risk
– Non-uniform contamination
• Equivalent equipment
54
![Page 55: Validation boot camp 3](https://reader034.vdocument.in/reader034/viewer/2022042613/554b8568b4c9056d5f8b4f26/html5/thumbnails/55.jpg)
SUMMARY – ANALYTICAL INCLUDING COMMON PROBLEMS
Understand residue • Solubility and stability • Validated analytical method for actual residue
– Specific or non-specific analytical methods
• API and cleaning agent residue
Recovery studies from product contact materials • API and cleaning agent
Swab / rinse testing on equipment • Most difficult to clean sampling sites • Use of auxiliary sampling equipment (extension pole)
Swab / rinse training of sampling personnel
55
![Page 56: Validation boot camp 3](https://reader034.vdocument.in/reader034/viewer/2022042613/554b8568b4c9056d5f8b4f26/html5/thumbnails/56.jpg)
SUMMARY STAGE 2 – PERFORMANCE
INCLUDING COMMON PROBLEMS
Cleaning Process Conformance Lots Cleaning equipment qualified Cleaning procedure specified (Not SOP) Cleaning documentation
– Request – Protocol – Results / Report
Manual cleaning – high risk
56
![Page 57: Validation boot camp 3](https://reader034.vdocument.in/reader034/viewer/2022042613/554b8568b4c9056d5f8b4f26/html5/thumbnails/57.jpg)
SUMMARY STAGE 3 -- MAINTAINING VALIDATION
Change control -- evaluate impact of change and validate (test) as necessary
Improve process Improve control to detect and reduce
variability Cleaning non-conformances and deviations Periodic Management Review
57
![Page 58: Validation boot camp 3](https://reader034.vdocument.in/reader034/viewer/2022042613/554b8568b4c9056d5f8b4f26/html5/thumbnails/58.jpg)
PAUL L. PLUTA, PhD
Editor-in-Chief Journal of Validation Technology Journal of GXP Compliance Advanstar Communications
Adjunct Associate Professor University of Illinois at Chicago (UIC) College of Pharmacy Chicago, IL, USA
Pharmaceutical industry experience
Contact: [email protected]
58