0 - 1VAUXHALL Astra GTCVAUXHALL Astra GTC

Owner’s ManualModel Year 2012Edition: October 2011TS 1708-B-12

Introduction .................................... 2In brief ............................................ 6Keys, doors and windows ............ 19Seats, restraints ........................... 33Storage ........................................ 51Instruments and controls ............. 62Lighting ........................................ 97Climate control ........................... 110Driving and operating ................. 118Vehicle care ............................... 154Service and maintenance .......... 194Technical data ........................... 197Customer information ................ 209Index .......................................... 212

Contents

2 Introduction

Introduction

Introduction 3

Vehicle specific dataPlease enter your vehicle's data onthe previous page to keep it easilyaccessible. This information isavailable in the sections "Service andmaintenance" and "Technical data"as well as on the identification plate.

IntroductionYour vehicle is a designedcombination of advanced technology,safety, environmental friendlinessand economy.This Owner's Manual provides youwith all the necessary information toenable you to drive your vehiclesafely and efficiently.Make sure your passengers areaware of the possible risk of accidentand injury which may result fromimproper use of the vehicle.You must always comply with thespecific laws and regulations of thecountry that you are in. These lawsmay differ from the information in thisOwner's Manual.

When this Owner's Manual refers toa workshop visit, we recommend yourVauxhall Authorised Repairer.All Vauxhall Authorised Repairersprovide first-class service atreasonable prices. Experiencedmechanics trained by Vauxhall workaccording to specific Vauxhallinstructions.The customer literature pack shouldalways be kept ready to hand in thevehicle.

Using this manual■ This manual describes all options

and features available for thismodel. Certain descriptions,including those for display andmenu functions, may not apply toyour vehicle due to model variant,country specifications, specialequipment or accessories.

■ The "In brief" section will give youan initial overview.

■ The table of contents at thebeginning of this manual and withineach section shows where theinformation is located.

■ The index will enable you to searchfor specific information.

■ This Owner's Manual depicts left-hand drive vehicles. Operation issimilar for right-hand drive vehicles.

■ The Owner's Manual uses thefactory engine designations. Thecorresponding sales designationscan be found in the section"Technical data".

■ Directional data, e.g. left or right, orfront or back, always relate to thedirection of travel.

■ The vehicle display screens maynot support your specific language.

■ Display messages and interiorlabelling are written in bold letters.

Danger, Warnings andCautions

9 Danger

Text marked 9 Danger providesinformation on risk of fatal injury.Disregarding this information mayendanger life.

4 Introduction

9 Warning

Text marked 9 Warning providesinformation on risk of accident orinjury. Disregarding thisinformation may lead to injury.

Caution

Text marked Caution providesinformation on possible damage tothe vehicle. Disregarding thisinformation may lead to vehicledamage.

SymbolsPage references are indicated with 3.3 means "see page".Thank you for choosing a Vauxhall.We wish you many hours ofpleasurable driving.Your Vauxhall Team

Introduction 5

6 In brief

In brief

Initial drive information

Vehicle unlocking

Press button c to unlock the doorsand load compartment. Open thedoors by pulling the handles.

To open the tailgate, push the brandemblem at the bottom half.Press button x to unlock and openthe tailgate while the doors remainlocked.Radio remote control 3 20, Centrallocking system 3 21, Loadcompartment 3 23.

In brief 7

Seat adjustmentSeat positioning

Pull handle, slide seat, releasehandle.Seat position 3 35, Seat adjustment3 35.

9 Danger

Do not sit nearer than 25 cm fromthe steering wheel, to permit safeairbag deployment.

Seat backrests

Pull lever, adjust inclination andrelease lever. Allow the seat toengage audibly.Seat position 3 35, Seat adjustment3 35, Seat folding 3 38.

Seat height

Lever pumping motionup = seat higherdown = seat lower

Seat position 3 35, Seat adjustment3 35.

8 In brief

Seat inclination

Lever pumping motionup = front end higherdown = front end lower

Seat position 3 35, Seat adjustment3 35.

Head restraint adjustment

Press the button, adjust height andengage.Head restraints 3 33.

Seat belt

Pull out the seat belt and engage inbelt buckle. The seat belt must not betwisted and must fit close against thebody. The backrest must not be tiltedback too far (maximum approx. 25 °).To release belt, press red button onbelt buckle.Seat position 3 35, Seat belts3 39, Airbag system 3 41.

In brief 9

Mirror adjustmentInterior mirror

To reduce dazzle, adjust the lever onthe underside of the mirror housing.Interior mirror 3 29, Automatic anti-dazzle interior mirror 3 29.

Exterior mirrors

Select the relevant exterior mirror andadjust it.Convex exterior mirrors 3 27,Electric adjustment 3 27, Foldingexterior mirrors 3 28, Heatedexterior mirrors 3 28.

Steering wheel adjustment

Unlock the lever, adjust the steeringwheel, then engage the lever andensure it is fully locked.Do not adjust the steering wheelunless the vehicle is stationary andthe steering wheel lock has beenreleased.Airbag system 3 41, Ignitionpositions 3 119.

10 In brief

Instrument panel overview

In brief 11

1 Power windows ..................... 302 Exterior mirrors ..................... 273 Cruise control ..................... 135

Speed limiter ....................... 1364 Side air vents ...................... 1165 Turn and lane-change

signals, headlight flash,low beam and high beam ... 104Exit lighting ......................... 108Parking lights ...................... 105Driver Information Centre ...... 80

6 Instruments .......................... 697 Steering wheel controls ....... 628 Driver Information Centre ...... 809 Windscreen wiper,

windscreen washersystem, headlight washersystem, rear wiper ................ 64

10 Central locking system .......... 21Hazard warning flashers .... 104Control indicator for airbagdeactivation .......................... 74Control indicator for frontpassenger seat belt ............. 74

11 Info-Display .......................... 83

12 Anti-theft alarm systemstatus LED ........................... 25

13 Centre air vents .................. 11614 Glovebox .............................. 5115 Sport mode ........................ 133

Tour mode .......................... 133Traction Control system ..... 132Electronic Stability Control . 132Parking assist ..................... 138Lane departure warning ..... 143Eco button ........................... 121

16 Climate control system ........ 11017 AUX input, USB input .......... 1018 Power outlet .......................... 6819 Selector lever, manual

transmission ....................... 128Automatic transmission ...... 125

20 Ignition switch withsteering wheel lock ............ 119

21 Horn ..................................... 63Driver airbag ........................ 42

22 Bonnet release lever .......... 15523 Storage compartment,

fuse box ............................. 17324 Steering wheel adjustment . . 62

25 Light switch .......................... 97Headlight rangeadjustment ........................... 99Front fog lights ................... 105Rear fog light ...................... 105Instrument illumination ....... 106

12 In brief

Exterior lighting

Turn light switch:7 = lights off8 = sidelights9 = headlights

Automatic light controlAUTO = automatic light control:

Headlights are switchedon and off automatically

m = activation or deactivationof the automatic lightcontrol

8 = sidelights9 = headlights

Fog lightsPress light switch:> = front fog lightsr = rear fog light

Lighting 3 97.

Headlight flash, high beam andlow beam

headlight flash = pull leverhigh beam = push leverlow beam = push or pull lever

Automatic light control 3 98, Highbeam 3 98, High beam assist3 98, Headlight flash 3 99,Adaptive forward lighting 3 100.

In brief 13

Turn and lane-change signals

lever up = right turn signallever down = left turn signal

Turn and lane-change signals3 104, Parking lights 3 105.

Hazard warning flashers

Operated with the ¨ button.Hazard warning flashers 3 104.

Horn

Press j.

14 In brief

Washer and wiper systemsWindscreen wiper

2 = fast1 = slowP = timed interval wiping or

automatic wiping with rainsensor

§ = off

For a single wipe when thewindscreen wiper is off, press thelever down.Windscreen wiper 3 64, Wiperblade replacement 3 161.

Windscreen and headlightwasher systems

Pull lever.Windscreen and headlight washersystem 3 64, Washer fluid 3 158.

Rear window wiper and washersystems

Press the rocker switch to activate therear window wiper:upperposition

= continuousoperation

lowerposition

= intermittentoperation

middleposition

= off

Rear window wiper/washer 3 66.

In brief 15

Push lever.Washer fluid is sprayed on the rearwindow and the wiper wipes a fewtimes.

Climate controlHeated rear window, heatedexterior mirrors

The heating is operated by pressingthe Ü button.Heated rear window 3 31.

Demisting and defrosting thewindows

Press button V.Set the temperature control to thehighest level.Cooling n on.Heated rear window Ü on.Climate control system 3 110.

16 In brief

TransmissionManual transmission

Reverse: with the vehicle stationary,wait 3 seconds after depressingclutch pedal and then press therelease button on the selector leverand engage the gear.If the gear does not engage, set thelever to neutral, release the clutchpedal and depress again; then repeatgear selection.Manual transmission 3 128.

Automatic transmission

P = parkR = reverseN = neutralD = drive

Manual mode: move selector leverfrom D to the left.< = higher gear] = lower gear

The selector lever can only be movedout of P when the ignition is on andthe brake pedal is applied. To engageP or R, press the release button.Automatic transmission 3 125.

Starting offCheck before starting off■ Tyre pressure and condition 3 177,3 206.

■ Engine oil level and fluid levels3 156.

■ All windows, mirrors, exteriorlighting and number plates are freefrom dirt, snow and ice and areoperational.

■ Proper position of mirrors, seats,and seat belts 3 27, 3 35,3 40.

■ Brake function at low speed,particularly if the brakes are wet.

In brief 17

Starting the engine

■ Turn key to position 1■ move the steering wheel slightly to

release the steering wheel lock■ operate clutch and brake■ automatic transmission in P or N■ do not operate accelerator pedal■ diesel engines: turn the key to

position 2 for preheating and waituntil control indicator !extinguishes

■ turn key to position 3 and releaseStarting the engine 3 119.

Stop-start system

If the vehicle is at a low speed or ata standstill and certain conditions arefulfilled, activate an Autostop asfollows:■ Depress the clutch pedal■ set the lever in neutral■ release the clutch pedalAn Autostop is indicated by theneedle at the AUTOSTOP position inthe tachometer.To restart the engine, depress theclutch pedal again.Stop-start system 3 121.

Parking■ Always apply the parking brake.

Activate the manual parking brakewithout pressing the release button.Apply as firmly as possible ona downhill slope or uphill slope.Depress foot brake at the sametime to reduce operating force.For vehicles with electrical parkingbrake, pull switch m.

■ Switch off the engine. Turn theignition key to position 0 andremove it. Turn the steering wheeluntil the steering wheel lock is feltto engage.For vehicles with automatictransmission, the key can only beremoved when the selector lever isin the P position.

■ If the vehicle is on a level surface oruphill slope, engage first gear or setthe selector lever to P beforeswitching off the ignition. On anuphill slope, turn the front wheelsaway from the kerb.If the vehicle is on a downhill slope,engage reverse gear or set the

18 In brief

selector lever to P before switchingoff the ignition. Turn the frontwheels towards the kerb.

■ Lock the vehicle with button e onthe radio remote control.Activate the anti-theft alarm system3 25.

■ Do not park the vehicle on an easilyignitable surface. The hightemperature of the exhaust systemcould ignite the surface.

■ Close the windows.■ The engine cooling fans may run

after the engine has been switchedoff 3 155.

■ After running at high engine speedsor with high engine loads, operatethe engine briefly at a low load orrun in neutral forapprox. 30 seconds beforeswitching off, in order to protect theturbocharger.

Keys, locks 3 19, Laying the vehicleup for a long period of time 3 154.

Keys, doors and windows 19

Keys, doors andwindows

Keys, locks ................................... 19Doors ........................................... 23Vehicle security ............................ 25Exterior mirrors ............................ 27Interior mirrors ............................. 29Windows ...................................... 29

Keys, locksKeysReplacement keysThe key number is specified in theCar Pass or on a detachable tag.The key number must be quotedwhen ordering replacement keys as itis a component of the immobilisersystem.Locks 3 191.

Lock cylindersDesigned to free-wheel if they areforcefully rotated without the correctkey or if the correct key is not fullyinserted. To reset, turn cylinder withthe correct key until its slot is vertical,remove key and then re-insert it. If thecylinder still free-wheels, turn the keythrough 180° and repeat operation.

Key with foldaway key section

Press button to extend. To fold thekey, first press the button.

Car PassThe Car Pass contains securityrelated vehicle data and shouldtherefore be kept in a safe place.When the vehicle is taken toa workshop, this vehicle data isneeded in order to perform certainoperations.

20 Keys, doors and windows

Radio remote control

Used to operate:■ Central locking system■ Anti-theft locking system■ Anti-theft alarm system■ Power windowsThe radio remote control has anapproximate range of up to20 metres. It can be restricted byexternal influences. The hazardwarning flashers confirm operation.Handle with care, protect frommoisture and high temperatures andavoid unnecessary operation.

FaultIf the central locking system cannotbe operated with the radio remotecontrol, it may be due to the following:■ Range exceeded■ Battery voltage too low■ Frequent, repeated operation of the

radio remote control while not inrange, which will require re-synchronisation

■ Overload of the central lockingsystem by operating at frequentintervals, the power supply isinterrupted for a short time

■ Interference from higher-powerradio waves from other sources

Unlocking 3 21.

Basic settingsSome settings can be changed in themenu Settings in the Info-Display.Vehicle personalisation 3 92.

Radio remote control batteryreplacementReplace the battery as soon as therange reduces.

Batteries do not belong in householdwaste. They must be disposed of atan appropriate recycling collectionpoint.

Key with foldaway key section

Keys, doors and windows 21

Extend the key and open the unit.Replace the battery (battery typeCR 2032), paying attention to theinstallation position. Close the unitand synchronise.

Radio remote controlsynchronisationAfter replacing the battery, unlock thedoor with the key in the driver's doorlock. The radio remote control will besynchronised when you switch on theignition.

Memorised settingsWhenever the key is removed fromthe ignition switch, the followingsettings are automatically memorisedby the key:■ Lighting■ Infotainment system■ Central locking system■ Sport mode settings■ Comfort settings

The saved settings are automaticallyused the next time the memorised keyis inserted into the ignition switch andturned to position 1 3 119.A precondition is that Personalizationby driver is activated in the personalsettings of the Graphic-Info-Display.This must be set for each key used.On vehicles equipped withColour-Info-Display, thepersonalisation is permanentlyactivated.Vehicle personalisation 3 92.

Central locking systemUnlocks and locks doors, loadcompartment and fuel filler flap.A pull on an interior door handleunlocks the respective door. Pullingthe handle once more opens the door.NoteIn the event of an accident in whichairbags or belt pretensioners aredeployed, the vehicle isautomatically unlocked.

NoteA short time after unlocking with theremote control the doors are lockedautomatically if no door has beenopened.

Unlocking

Press button c.Two settings are selectable:■ To unlock only the driver's door,

load compartment and fuel fillerflap, press button c once. To unlockboth doors, press button c twiceor

22 Keys, doors and windows

■ press button c once to unlock bothdoors, load compartment and fuelfiller flap

The setting can be changed in themenu Settings in the Info-Display.Vehicle personalisation 3 92.The setting can be saved for the keybeing used. Memorised settings3 21.Unlocking and opening the tailgate3 23.

LockingClose doors, load compartment andfuel filler flap.

Press button e.If the driver's door is not closedproperly, the central locking systemwill not work.

Central locking buttonsLocks or unlocks both doors, the loadcompartment and fuel filler flap fromthe passenger compartment.

Press the e button to lock.Press the c button to unlock.

Fault in radio remote controlsystem

Unlocking

Manually unlock the driver's door byturning the key in the lock. Switch onthe ignition and press the centrallocking button c to unlockpassenger's door, load compartmentand fuel filler flap. By switching on theignition, the anti-theft locking systemis deactivated.

LockingManually lock the driver's door byturning the key in the lock.

Keys, doors and windows 23

Fault in central locking system

UnlockingManually unlock the driver's door byturning the key in the lock. Thepassenger's door can be opened bypulling the interior handle twice. Theload compartment and fuel filler flapcannot be opened. To deactivate theanti-theft locking system, switch onthe ignition 3 25.

LockingPush inside locking knob ofpassenger's door. Then close thedriver's door and lock it from theoutside with the key. The fuel filler flapand tailgate cannot be locked.

Automatic lockingThis security feature can beconfigured to automatically lock thedoors, load compartment and fuelfiller flap as soon as a certain speedis exceeded.Additionally it is configurable tounlock the driver's door or all doorsafter the ignition is switched off and

the ignition key is removed (manualtransmission) or the selector lever ismoved to P position (automatictransmission).Settings can be changed in the menuSettings in the Info-Display. Vehiclepersonalisation 3 92.The settings can be saved for the keybeing used 3 21.

DoorsLoad compartmentTailgate

Opening

Press button x on radio remotecontrol or push the brand emblem atthe bottom half to unlock and open thetailgate.

24 Keys, doors and windows

Pressing button x opens thetailgate even if the doors are locked.Central locking system 3 21.

Closing

Use the interior handle.Do not touch the brand emblem whilstclosing as this could unlock thetailgate again.Central locking system 3 21.

General hints for operatingtailgate

9 Warning

Do not drive with the tailgate openor ajar, e.g. when transportingbulky objects, since toxic exhaustgases, which can not be seen orsmelled, could enter the vehicle.This can cause unconsciousnessand even death.

Caution

Before opening the tailgate checkoverhead obstructions, such asa garage door, to avoid damage tothe tailgate. Always check themoving area above and behind thetailgate.

NoteThe installation of certain heavyaccessories onto the tailgate mayaffect its ability to remain open.

Keys, doors and windows 25

Vehicle securityAnti-theft locking system

9 Warning

Do not use the system if there arepeople in the vehicle! The doorscannot be unlocked from theinside.

The system deadlocks the doors. Thedoors must be closed otherwise thesystem cannot be activated.If the ignition was on, the driver's doormust be opened and closed once sothat the vehicle can be secured.Unlocking the vehicle disables themechanical anti-theft locking system.This is not possible with the centrallocking button.

Activating

Press e on the radio remote controltwice within 15 seconds.

Anti-theft alarm systemThe anti-theft alarm system iscombined with the central lockingsystem.It monitors:■ Doors, tailgate, bonnet■ Passenger compartment including

adjoining load compartment■ Vehicle inclination, e.g. if it is raised■ Ignition

Activation■ Self-activated 30 seconds after

locking the vehicle (initialisation ofthe system)

■ Directly by pressing e on the radioremote control once more afterlocking

NoteChanges to the vehicle interior, suchas the use of seat covers and openwindows, could impair the functionof passenger compartmentmonitoring.

26 Keys, doors and windows

Activation without monitoring ofpassenger compartment andvehicle inclination

Switch off the monitoring ofpassenger compartment and vehicleinclination when animals are beingleft in the vehicle, because of highvolume ultrasonic signals ormovements triggering the alarm. Alsoswitch off when the vehicle is ona ferry or train.1. Close tailgate, bonnet, windows.2. Press button o. LED in the

button o illuminates fora maximum of 10 minutes.

3. Close doors.4. Activate the anti-theft alarm

system.Status message is displayed in theDriver Information Centre.

Status LED

Status LED is integrated in the sensoron top of the instrument panel.

Status during the first 30 seconds ofanti-theft alarm system activation:LEDilluminates

= test, arming delay.

LED flashesquickly

= doors, tailgate orbonnet notcompletely closed,or system fault.

Status after system is armed:LED flashesslowly

= system is armed.

Seek the assistance of a workshop inthe event of faults.

DeactivationUnlocking the vehicle deactivates theanti-theft alarm system.

AlarmWhen triggered, the alarm sounds viaa separate battery-backed powersounder, and the hazard warninglights flash simultaneously. Thenumber and duration of alarm signalsare stipulated by legislation.

Keys, doors and windows 27

The alarm can be silenced bypressing any button on the radioremote control or by switching on theignition.The anti-theft alarm system can bedeactivated only by pressing buttonc or by switching on the ignition.A triggered alarm, which has not beeninterrupted by the driver, will beindicated by the hazard warninglights. They will flash quickly threetimes when the vehicle is unlockednext time with the radio remotecontrol. Additionally a warningmessage or a warning code isdisplayed in the Driver InformationCentre after switching on the ignition.Vehicle messages 3 85.If the vehicle's battery is to bedisconnected (e.g. for maintenancework), the alarm siren must bedeactivated as follows: switch theignition on then off, then disconnectthe vehicle's battery within15 seconds.

ImmobiliserThe system is part of the ignitionswitch and checks whether thevehicle is allowed to be started withthe key being used.The immobiliser is activatedautomatically after the key has beenremoved from the ignition switch.If the control indicator d flashes whenthe ignition is on, there is a fault in thesystem; the engine cannot be started.Switch off the ignition and repeat thestart attempt.If the control indicator continuesflashing, attempt to start the engineusing the spare key and seek theassistance of a workshop.NoteThe immobiliser does not lock thedoors. You should always lock thevehicle after leaving it and switch onthe anti-theft alarm system 3 21,3 25.

Control indicator d 3 79.

Exterior mirrorsConvex shapeThe convex exterior mirror containsan aspherical area and reduces blindspots. The shape of the mirror makesobjects appear smaller, which willaffect the ability to estimatedistances.

Electric adjustment

Select the relevant exterior mirror byturning the control to left (L) or right(R). Then swivel the control to adjustthe mirror.

28 Keys, doors and windows

In position 0 no mirror is selected.

Folding

For pedestrian safety, the exteriormirrors will swing out of their normalmounting position if they are struckwith sufficient force. Reposition themirror by applying slight pressure tothe mirror housing.

Electric folding

Turn control to 0, then push thecontrol down. Both exterior mirrorswill fold.Push the control down again - bothexterior mirrors return to their originalposition.If an electrically folded mirror ismanually extended, pressing downthe control will only electrically extendthe other mirror.

Heated

Operated by pressing the Ü button.Heating works with the enginerunning and is switched offautomatically after a short time.

Keys, doors and windows 29

Interior mirrorsManual anti-dazzle

To reduce dazzle, adjust the lever onthe underside of the mirror housing.

Automatic anti-dazzle

Dazzle from following vehicles atnight is automatically reduced.

WindowsWindscreenHeat-reflecting windscreenThe heat-reflecting windscreen hasa coating which reflects solarradiation. Also data signals, e.g. fromtoll stations, might be reflected.

The marked areas of the windscreenbehind the interior mirror are notcovered with the coating. Devices forelectronic data recording and fee

30 Keys, doors and windows

payment must be attached in theseareas. Otherwise data recordingmalfunctions may occur.

Power windows

9 Warning

Take care when operating thepower windows. Risk of injury,particularly to children.Keep a close watch on thewindows when closing them.Ensure that nothing becomestrapped in them as they move.

Switch on ignition to operate powerwindows. Retained power off 3 119.

Operate the switch for the respectivewindow by pushing to open or pullingto close.Pushing or pulling gently to the firstdetent: window moves up or down aslong as the switch is operated.Pushing or pulling firmly to the seconddetent and then releasing: windowmoves up or down automatically withsafety function enabled. To stopmovement, operate the switch oncemore in the same direction.

Safety functionIf the window glass encountersresistance above the middle of thewindow during automatic closing, it isimmediately stopped and openedagain.

Override safety functionIn the event of closing difficulties dueto frost or the like, switch on theignition, then pull the switch to the firstdetent and hold. The window movesup without safety function enabled.To stop movement, release theswitch.

Operating windows from outsideThe windows can be operatedremotely from outside the vehicle.

Keys, doors and windows 31

Press and hold c button to openwindows.Press and hold e button to closewindows.Release button to stop windowmovement.If the windows are fully opened orclosed, the hazard warning lights willflash twice.

OverloadIf the windows are repeatedlyoperated within short intervals, thewindow operation is disabled forsome time.

Initialising the power windowsIf the windows cannot be closedautomatically (e.g. afterdisconnecting the vehicle battery),a warning message or a warning codeis displayed in the Driver InformationCentre.Vehicle messages 3 85.Activate the window electronics asfollows:1. Close doors.2. Switch on ignition.3. Pull switch until the window is

closed and keep pulling foradditional 2 seconds.

4. Repeat for each window.

Heated rear window

Operated by pressing the Ü button.Heating works with the enginerunning and is switched offautomatically after a short time.Depending on the engine type, theheated rear window comes onautomatically when the diesel particlefilter is being cleaned.

Sun visorsThe sun visors can be folded down orswivelled to the side to preventdazzling.

32 Keys, doors and windows

If the sun visors have integral mirrors,the mirror covers should be closedwhen driving.A ticket holder is located on thebackside of the sun visor.

Seats, restraints 33

Seats, restraints

Head restraints ............................ 33Front seats ................................... 35Rear seats ................................... 39Seat belts ..................................... 39Airbag system .............................. 41Child restraints ............................. 45

Head restraints

Position

9 Warning

Only drive with the head restraintset to the proper position.

The upper edge of the head restraintshould be at upper head level. If thisis not possible for extremely tallpeople, set to highest position, andset to lowest position for small people.

Adjustment

Head restraints on front seats

Height adjustmentPress the button, adjust height andengage.

34 Seats, restraints

Horizontal adjustment

To adjust horizontally, pull the headrestraint forwards. It engages inseveral positions.To return to its rearmost position, pullfully forwards and release.

Head restraints on rear seats

Height adjustmentPull the head restraint upwards orpress the catch to release and pushthe head restraint downwards.

RemovalPress both catches, pull the headrestraint upwards and remove.

Active head restraintsIn the event of a rear-end impact, thefront parts of the active headrestraints are moved slightly

forwards. Thus the head is supportedso that the risk of whiplash injury isreduced.NoteApproved accessories may only beattached if the seat is not in use.

Seats, restraints 35

Front seatsSeat position

9 Warning

Only drive with the seat correctlyadjusted.

■ Sit with buttocks as far back againstthe backrest as possible. Adjust thedistance between the seat and thepedals so that legs are slightlyangled when pressing the pedals.Slide the front passenger seat asfar back as possible.

■ Sit with shoulders as far backagainst the backrest as possible.Set the backrest rake so that it ispossible to easily reach thesteering wheel with arms slightlybent. Maintain contact betweenshoulders and the backrest whenturning the steering wheel. Do notangle the backrest too far back. Werecommend a maximum rake ofapprox. 25°.

■ Adjust the steering wheel 3 62.■ Set seat height high enough to

have a clear field of vision on allsides and of all display instruments.There should be at least one handof clearance between head and theroof frame. Your thighs should restlightly on the seat without pressinginto it.

■ Adjust the head restraint 3 33.■ Adjust the thigh support so that

there is a space approx. two fingerswide between the edge of the seatand the hollow of the knee.

■ Adjust the lumbar support so that itsupports the natural shape of thespine.

Seat adjustment

9 Danger

Do not sit nearer than 25 cm fromthe steering wheel, to permit safeairbag deployment.

9 Warning

Never adjust seats while driving asthey could move uncontrollably.

36 Seats, restraints

9 Warning

Never store any subjects underthe seats.

■ Drive only with engaged seats andbackrests.

Seat positioning

Pull handle, slide seat, releasehandle.

Seat backrests

Pull lever, adjust inclination andrelease lever. Allow the backrest toengage audibly.

Seat height

Lever pumping motionup = seat higherdown = seat lower

Seats, restraints 37

Seat inclination

Lever pumping motionup = front end higherdown = front end lower

Lumbar support

Adjust lumbar support using the four-way switch to suit personalrequirements.Moving support up and down: pushswitch up or down.Increasing and decreasing support:push switch forwards or backwards.

Adjustable thigh support

Pull the lever and slide the thighsupport.

38 Seats, restraints

Seat folding

Lift release lever and fold backrestforwards. Slide seat forwards.To restore, slide the seat backwards.Move the backrest against theresistance to upright and engage.The memory function let the seatengage in its original position.Do not operate backrest inclinationlever while backrest tilted forward.

9 Danger

To avoid injury, fold backrest aspossible from upright position.

Armrest

The armrest can be slid forwards by10 cm. Under the armrest there isa storage compartment.Armrest storage 3 53.

Heating

Adjust heating to the desired settingby pressing the ß button for therespective seat one or more times.The control indicator in the buttonindicates the setting.Prolonged use of the highest settingfor people with sensitive skin is notrecommended.Seat heating is operational whenengine is running and during anAutostop.Stop-start system 3 121.

Seats, restraints 39

Rear seatsArmrest

Fold armrest down. The armrestcontains cupholders and a storagebox.

Seat belts

The seat belts are locked duringheavy acceleration or deceleration ofthe vehicle holding the occupants inthe sitting position. Therefore the riskof injury is considerably reduced.

9 Warning

Fasten seat belt before each trip.In the event of an accident, peoplenot wearing seat belts endangertheir fellow occupants andthemselves.

Seat belts are designed to be used byonly one person at a time. They arenot suitable for people smaller than150 cm. Child restraint system3 45.Periodically check all parts of the beltsystem for damage, pollution andproper functionality.Have damaged componentsreplaced. After an accident, have thebelts and triggered belt pretensionersreplaced by a workshop.NoteMake sure that the belts are notdamaged by shoes or sharp-edgedobjects or trapped. Prevent dirt fromgetting into the belt retractors.

Seat belt reminderFront seats are equipped with a seatbelt reminder, indicated for driver seatas control indicator X in thetachometer 3 74 and for passengerseat in the centre console 3 71.

40 Seats, restraints

Belt force limitersOn the front seats, stress on the bodyis reduced by the gradual release ofthe belt during a collision.

Belt pretensionersIn the event of a head-on or rear-endcollision of a certain severity, the frontseat belts are tightened.

9 Warning

Incorrect handling (e.g. removal orfitting of belts) can trigger the beltpretensioners.

Deployment of the belt pretensionersis indicated by continuous illuminationof control indicator v 3 74.Triggered belt pretensioners must bereplaced by a workshop. Beltpretensioners can only be triggeredonce.

NoteDo not affix or install accessories orother objects that may interfere withthe operation of the beltpretensioners. Do not make anymodifications to belt pretensionercomponents as this will invalidatethe vehicle type approval.

Three-point seat beltFastening

Withdraw the belt from the retractor,guide it untwisted across the bodyand insert the latch plate into the

buckle. Tighten the lap belt regularlywhilst driving by pulling the shoulderbelt.

Loose or bulky clothing prevents thebelt from fitting snugly. Do not placeobjects such as handbags or mobilephones between the belt and yourbody.

9 Warning

The belt must not rest against hardor fragile objects in the pockets ofyour clothing.

Seat belt reminder X 3 74.

Seats, restraints 41

Removing

To release belt, press red button onbelt buckle.

Seat belts on the rear seatsThe seat belt for the rear centre seatcan only be withdrawn from theretractor if the backrest is engaged inupright position.

Using the seat belt whilepregnant

9 Warning

The lap belt must be positioned aslow as possible across the pelvisto prevent pressure on theabdomen.

Airbag systemThe airbag system consists ofa number of individual systemsdepending on the scope ofequipment.When triggered the airbags inflatewithin milliseconds. They also deflateso quickly that it is often unnoticeableduring the collision.

9 Warning

If handled improperly the airbagsystems can be triggered in anexplosive manner.

42 Seats, restraints

NoteThe airbag systems and beltpretensioner control electronics arelocated in the centre console area.Do not put any magnetic objects inthis area.Do not stick anything on the airbagcovers and do not cover them withother materials.Each airbag is triggered only once.Have deployed airbags replaced bya workshop. Furthermore, it might benecessary to have the steeringwheel, the instrument panel, parts ofthe panelling, the door seals,handles and the seats replaced.Do not make any modifications tothe airbag system as this willinvalidate the vehicle type approval.

When the airbags inflate escaping hotgases may cause burns.Control indicator v for airbag systems3 74.

Front airbag systemThe front airbag system consists ofone airbag in the steering wheel andone in the instrument panel on thefront passenger side. These can beidentified by the word AIRBAG.

There are also warning labels on bothsides of the sunblind on the frontpassenger side.The front airbag system is triggered inthe event of a front-end impact ofa certain severity. The ignition mustbe switched on.

The inflated airbags cushion theimpact, thereby reducing the risk ofinjury to the upper body and head ofthe front seat occupantsconsiderably.

Seats, restraints 43

9 Warning

Optimum protection is onlyprovided when the seat is in theproper position 3 35.Keep the area in which the airbaginflates clear of obstructions.Fit the seat belt correctly andengage securely. Only then theairbag is able to protect.

Side airbag system

The side airbag system consists of anairbag in each front seat backrest.This can be identified by the wordAIRBAG.The side airbag system is triggered inthe event of a side impact of a certainseverity. The ignition must beswitched on.

The inflated airbags cushion theimpact, thereby reducing the risk ofinjury to the upper body and pelvis inthe event of a side-on collisionconsiderably.

9 Warning

Keep the area in which the airbaginflates clear of obstructions.

NoteOnly use protective seat covers thathave been approved for the vehicle.Be careful not to cover the airbags.

Curtain airbag systemThe curtain airbag system consists ofan airbag in the roof frame on eachside. This can be identified by theword AIRBAG on the roof pillars.The curtain airbag system is triggeredin the event of a side-on impact ofa certain severity. The ignition mustbe switched on.

44 Seats, restraints

The inflated airbags cushion theimpact, thereby reducing the risk ofinjury to the head in the event ofa side-on impact considerably.

9 Warning

Keep the area in which the airbaginflates clear of obstructions.The hooks on the handles in theroof frame are only suitable forhanging up light articles ofclothing, without coat hangers. Donot keep any items in theseclothes.

Airbag deactivationThe front passenger airbag systemhas to be deactivated if a childrestraint system is to be fitted on thisseat. The side airbag and curtainairbag systems, the beltpretensioners and all driver airbagsystems will remain active.

The front passenger airbag systemcan be deactivated via a key-operated switch on the right side ofthe instrument panel.

Use the ignition key to choose theposition:*OFF = front passenger airbag is

deactivated and will notinflate in the event ofa collision. Controlindicator *OFFilluminates continuously inthe centre console. A childrestraint system can beinstalled in accordancewith the chart Childrestraint installationlocations 3 47. No adultperson is allowed tooccupy the frontpassenger seat.

VON = front passenger airbag isactive. A child restraintsystem must not beinstalled.

Seats, restraints 45

9 Danger

Risk of fatal injury for a child usinga child restraint system on a seatwith activated front passengerairbag.Risk of fatal injury for an adultperson on a seat with deactivatedfront passenger airbag.

As long as the control indicator*OFF is not illuminated, the frontpassenger airbag system will inflatein the event of a collision.

If both control indicators areilluminated at the same time, there isa system failure. The status of thesystem is not discernible, thereforeno person is allowed to occupy thefront passenger seat. Contacta workshop immediately.Consult a workshop immediately ifneither of the two control indicators isilluminated.Change status only when the vehicleis stopped with the ignition off.Status remains until the next change.Control indicator for airbagdeactivation 3 74.

Child restraintsChild restraint systemsWe recommend the Vauxhall childrestraint system which is tailoredspecifically to the vehicle.When a child restraint system is beingused, pay attention to the followingusage and installation instructionsand also those supplied with the childrestraint system.Always comply with local or nationalregulations. In some countries, theuse of child restraint systems isforbidden on certain seats.

46 Seats, restraints

9 Warning

When using a child restraintsystem on the front passengerseat, the airbag systems for thefront passenger seat must bedeactivated; if not, the triggering ofthe airbags poses a risk of fatalinjury to the child.This is especially the case if rear-facing child restraint systems areused on the front passenger seat.

Selecting the right systemThe rear seats are the mostconvenient location to fasten a childrestraint system.Children should travel facingrearwards in the vehicle as long aspossible. This makes sure that thechild's backbone, which is still veryweak, is under less strain in the eventof an accident.Children under the age of 12 yearsthat are smaller than 150 cm are onlyallowed to travel in a restraint systemthat is suitable for the child. Suitable

are restraint systems that comply withECE 44-03 or ECE 44-04. Sincea proper position of the belt is rarelypossible with a child that is smallerthan 150 cm, we strongly advise theuse of an appropriate child restraintsystem, even though this might, dueto the age of the child, no longer belegally binding.Ensure that the child restraint systemto be installed is compatible with thevehicle type.Ensure that the mounting location ofthe child restraint system within thevehicle is correct.Allow children to enter and exit thevehicle only on the side facing awayfrom the traffic.When the child restraint system is notin use, secure the seat with a seat beltor remove it from the vehicle.NoteDo not stick anything on the childrestraint systems and do not coverthem with any other materials.

A child restraint system which hasbeen subjected to stress in anaccident must be replaced.

Seats, restraints 47

Child restraint installation locationsPermissible options for fitting a child restraint system

Weight and age classOn front passenger seat

On rear outboard seats On rear centre seatactivated airbag deactivated airbag

Group 0: up to 10 kgor approx. 10 months

X U1 U2 U

Group 0+: up to 13 kgor approx. 2 years

X U1 U2 U

Group I: 9 to 18 kgor approx. 8 months to 4 years

X U1 U2 U

Group II: 15 to 25 kgor approx. 3 to 7 years

X X U U

Group III: 22 to 36 kgor approx. 6 to 12 years

X X U U

1 = Only if front passenger seat airbag system is deactivated. If the child restraint system is being secured using a three-point seat belt, move seat height adjustment to uppermost position and ensure that vehicle safety belt runs forwardsfrom the upper anchorage point. Adjust seat backrest inclination as far as necessary to a vertical position to ensurethat the belt is tight on the buckle side.

2 = Seat available with ISOFIX and Top-Tether mounting brackets 3 50.U = Universal suitability in conjunction with three-point seat belt.X = No child restraint system permitted in this weight class.

48 Seats, restraints

Permissible options for fitting an ISOFIX child restraint systemWeight class Size class Fixture On front passenger seat On rear outboard seats On rear centre seat

Group 0: up to 10 kg E ISO/R1 X IL X

Group 0+: up to 13 kg E ISO/R1 X IL X

D ISO/R2 X IL X

C ISO/R3 X IL X

Group I: 9 to 18 kg D ISO/R2 X IL X

C ISO/R3 X IL X

B ISO/F2 X IL, IUF X

B1 ISO/F2X X IL, IUF X

A ISO/F3 X IL, IUF X

IL = Suitable for particular ISOFIX restraint systems of the 'specific-vehicle', 'restricted' or 'semi-universal' categories.The ISOFIX restraint system must be approved for the specific vehicle type.

IUF = Suitable for ISOFIX forward-facing child restraint systems of universal category approved for use in this weight class.X = No ISOFIX child restraint system approved in this weight class.

Seats, restraints 49

ISOFIX size class and seat deviceA – ISO/F3 = Forward-facing child restraint system for children of maximum size in the weight class 9 to 18 kg.B – ISO/F2 = Forward-facing child restraint system for smaller children in the weight class 9 to 18 kg.B1 – ISO/F2X = Forward-facing child restraint system for smaller children in the weight class 9 to 18 kg.C – ISO/R3 = Rear-facing child restraint system for children of maximum size in the weight class up to 13 kg.D – ISO/R2 = Rear-facing child restraint system for smaller children in the weight class up to 13 kg.E – ISO/R1 = Rear-facing child restraint system for young children in the weight class up to 13 kg.

50 Seats, restraints

ISOFIX child restraintsystems

Fasten vehicle-approved ISOFIXchild restraint systems to the ISOFIXmounting brackets. Specific vehicleISOFIX child restraint systempositions are marked in the table byIL.ISOFIX mounting brackets areindicated by a label on the backrest.

Top-tether fastening eyesTop-Tether fastening eyes aremarked with the symbol : for a childseat.

In addition to the ISOFIX mountingfasten the Top-Tether strap to theTop-Tether fastening eyes. The strapmust run between the two guide rodsof the head restraint.ISOFIX child restraint systems ofuniversal category positions aremarked in the table by IUF.

Storage 51

Storage

Storage compartments ................ 51Load compartment ....................... 54Roof rack system ......................... 60Loading information ..................... 60

Storage compartmentsGlovebox

The glovebox features a pen holder,a credit card holder and a coin holder.The intermediate shelf can beremoved.The glovebox should be closed whilstdriving.

Cupholders

Cupholders are located in the centreconsole.

52 Storage

Depending on the version,cupholders are located under a coverin the centre console. Slide coverbackwards. Bottles can be stowedafter folding up the intermediate shelf3 53.

Additional cupholders are located inthe rear armrest. Fold down thearmrest.

Front storage

A storage compartment is locatednext to the steering wheel.

Sunglasses storage

Fold down and open.Do not use for storing heavy objects.

Storage 53

Armrest storageStorage under the front armrest

Press button to fold up the armrest.The armrest must be in rearmostposition.

Storage in the rear armrest

Fold down armrest and open cover.Close cover before folding thearmrest up.

Centre console storageFront console

The storage container can be used tostore small items.Depending on the version, a storagecompartment is located undera cover.Slide cover backwards.

54 Storage

Press button to remove the frame ofthe cupholder. The frame can bestowed in the glovebox.

A further storage compartment islocated under the intermediate shelf.Fold up the intermediate shelf and fixit in the vertical position. The frame ofthe cupholder can be reintegrated tostow bottles.

Rear console

Pull out the drawer.

Caution

Do not use for ashes or for otherglowing items.

Load compartmentThe rear seat backrest is divided intotwo parts. Both parts can be foldeddown.

Load compartment extensionRemove the load compartment coverif necessary.Press and hold the catch, then pushthe head restraints down.Fold up the rear armrest.

Storage 55

Guide the seat belts through sidesupports to protect them againstdamage. When folding the backrests,pull the seat belts along with them.Pull the release lever on one or bothsides and fold down the backrestsonto the seat cushion.

Take the seat belt out of the seatbackrest guide and put it behind theretainer as shown in the illustration.To fold up, raise the backrests andguide them into an upright positionuntil they engage audibly.

Ensure that the seat belts of theoutboard seats are placed in thecorresponding belt guides.

The backrests are properly engagedwhen the red marks on both sidesnear the release lever are no longervisible.

9 Warning

When folding up, ensure thatbackrests are securely locked inposition before driving. Failure todo so may result in personal injuryor damage to load or vehicle in theevent of heavy braking or collision.

The seat belt of the centre seat couldbe blocked when the backrest isfolded up too quickly. To unlock theretractor, push in the seat belt or pullit out by approx. 20 mm and then letgo.

56 Storage

Open the pass-through in therear centre backrestFold down the rear armrest.

Pull the grip and open the cover.Suitable for loading long, narrowobjects.Ensure that the cover engages afterfolding up.

The closed cover can be securedfrom the side of the loadcompartment. Turn the knob 90°:knobhorizontal

= cover secured fromthe side of thepassengercompartment

knobvertical

= cover not secured

Rear storage

Press both buttons and fold downcover.Maximum load: 0.5 kg.

Load compartment coverDo not place any objects on the cover.

Storage 57

Removing

Unhook retaining straps from tailgate.

Lift cover at the rear and push itupwards at the front.Remove the cover.If the height adjustable cover ismounted in the middle or upperposition, the load compartment covercan be stowed below it.Height adjustable cover 3 57.

FittingEngage cover in side guides and folddownwards. Attach retaining straps totailgate.

Rear floor storage coverRear floor cover

The rear floor cover can be lifted.Hinge the loop into the hook on thelower side of the load compartmentcover.

Caution

Only use the hook for hanging upthe rear floor cover and the heightadjustable cover.

58 Storage

Height adjustable cover

The height adjustable cover can bemounted in three positions:■ directly above the rear floor cover

(1),■ in a middle position (2)■ in an upper position (3).

Caution

Ensure that the front and rear endof the height adjustable cover areattached to the same level.

Lifting

To lift the cover to a higher level, pullthe loop backwards and lift the rearedge of the cover onto thecorresponding supports.

Lowering

To lower the cover, pull the strapbackwards and push down the frontcentre of the cover at the same time.

Caution

Do not lower the height adjustablecover to position 1 in vehiclesequipped with subwoofer. Thesubwoofer could be damaged.

Storage 59

Note■ If mounted in position 2 or 3, the

space between the rear floorcover and the height adjustablecover can be used as a stowagecompartment.

■ The height adjustable cover canbe lifted and hooked in with thestrap when it is mounted inposition 1 or 2.

■ If mounted in position 2, an almostcompletely flat load bay is createdif the rear seat backrests arefolded forwards.

■ Opening the side covers (e.g.when exchanging the rear lightbulbs) is only possible with theheight adjustable cover mountedin position 1 or 2.

Caution

The height adjustable cover isable to withstand a load of no morethan 100 kg.

Lashing eyes

The lashing eyes are designed tosecure items against slippage, e.g.using lashing straps or luggage net.

Warning triangle

Stow the warning triangle in the spacebehind the strap on the right side ofthe load compartment.Depending on the equipment, thewarning triangle can be stored ina storage compartment below thefloor cover.

60 Storage

First aid kit

Stow the first aid kit in the stowagecompartment behind the warningtriangle.Use the recesses to fold down thecover.Depending on the equipment, the firstaid kit can be stored in the rearstorage 3 56.

Roof rack systemRoof rackFor safety reasons and to avoiddamage to the roof, the vehicleapproved roof rack system isrecommended. For furtherinformation contact your workshop.Follow the installation instructionsand remove the roof rack when not inuse.

Mounting roof rack

Detach the cover from each mountingpoint by using a coin.

Loading information

■ Heavy objects in the loadcompartment should be placedagainst the seat backrests. Ensurethat the backrests are securelyengaged. If objects can be stacked,heavier objects should be placed atthe bottom.

■ Secure objects with lashing strapsattached to the lashing eyes 3 59.Attach the height adjustable coverin the lowest position (1) 3 57.

Storage 61

■ Use the four hooks at the sidewallsof the load compartment forhanging up carrier bags. Maximumload: 5 kg per hook.

■ Secure loose objects in the loadcompartment to prevent them fromsliding.

■ When transporting objects in theload compartment, the backrests ofthe rear seats must not be angledforward.

■ Do not allow the load to protrudeabove the upper edge of thebackrests.

■ Do not place any objects on theload compartment cover or theinstrument panel, and do not coverthe sensor on top of the instrumentpanel.

■ The load must not obstruct theoperation of the pedals, parkingbrake and gear selector lever, orhinder the freedom of movement ofthe driver. Do not place anyunsecured objects in the interior.

■ Do not drive with an open loadcompartment.

9 Warning

Always make sure that the load inthe vehicle is securely stowed.Otherwise objects can be thrownaround inside the vehicle andcause personal injury or damageto the load or car.

■ The payload is the differencebetween the permitted grossvehicle weight (see identificationplate 3 197) and the EC kerbweight.To calculate the payload, enter thedata for your vehicle in the Weightstable at the front of this manual.The EC kerb weight includesweights for the driver (68 kg),luggage (7 kg) and all fluids (tank90 % full).Optional equipment andaccessories increase the kerbweight.

■ Driving with a roof load increasesthe sensitivity of the vehicle tocross-winds and has a detrimentaleffect on vehicle handling due to

the vehicle's higher centre ofgravity. Distribute the load evenlyand secure it properly with retainingstraps. Adjust the tyre pressure andvehicle speed according to the loadconditions. Check and retighten thestraps frequently.Do not drive faster than 75 mph.The permissible roof load is 75 kg.The roof load is the combinedweight of the roof rack and the load.

62 Instruments and controls

Instruments andcontrols

Controls ....................................... 62Warning lights, gauges andindicators ..................................... 69Information displays ..................... 80Vehicle messages ........................ 85Trip computer ............................... 89Vehicle personalisation ................ 92

ControlsSteering wheel adjustment

Unlock lever, adjust steering wheel,then engage lever and ensure it isfully locked.Do not adjust steering wheel unlessvehicle is stationary and steeringwheel lock has been released.

Steering wheel controls

The Infotainment system, the cruisecontrol and a connected mobilephone can be operated via thecontrols on the steering wheel.Further information is available in theInfotainment system manual.Cruise control 3 135.

Instruments and controls 63

Heated steering wheel

Activate heating by pressing *button. Activation is indicated by theLED in the button.

The recommended grip areas of thesteering wheel are heated quickerand to a higher temperature than theother areas.Heating is operational when theengine is running and during anAutostop.Stop-start system 3 121.

Horn

Press j.

64 Instruments and controls

Windscreen wiper/washerWindscreen wiper

2 = fast1 = slowP = interval wiping§ = off

For a single wipe when thewindscreen wiper is off, press thelever down.Do not use if the windscreen is frozen.Switch off in car washes.

Adjustable wiper interval

Wiper lever in position P.Turn the adjuster wheel to adjust thedesired wipe interval:shortinterval

= turn adjuster wheelupwards

longinterval

= turn adjuster wheeldownwards

Automatic wiping with rain sensor

P = automatic wiping with rainsensor

The rain sensor detects the amount ofwater on the windscreen andautomatically regulates the frequencyof the windscreen wiper.If the wiper frequency is above20 seconds the wiper arm movesslightly down to park position.

Instruments and controls 65

Adjustable sensitivity of the rainsensor

Turn the adjuster wheel to adjust thesensitivity:lowsensitivity

= turn adjuster wheeldownwards

highsensitivity

= turn adjuster wheelupwards

Keep the sensor free from dust, dirtand ice.

Windscreen and headlightwasher

Pull lever. Washer fluid is sprayedonto the windscreen and the wiperwipes a few times.If the headlights are on, washer fluidis also sprayed onto the headlights,provided that the lever is pulledsufficiently long. Afterwards theheadlight washer system isinoperable for 5 wash cycles or untilengine or headlights have beenswitched off and on again.

66 Instruments and controls

Rear window wiper/washer

Press the rocker switch to activate therear window wiper:upperposition

= continuousoperation

lowerposition

= intermittentoperation

middleposition

= off

Push lever. Washer fluid is sprayedonto the rear window and the wiperwipes a few times.Do not use if the rear window isfrozen.Switch off in car washes.The rear window wiper comes onautomatically when the windscreenwiper is switched on and reverse gearis engaged.Activation or deactivation of thisfunction can be changed in the menuSettings in the Info-Display.Vehicle personalisation 3 92.

The rear window washer system isdeactivated when the fluid level islow.

Outside temperature

A drop in temperature is indicatedimmediately and a rise in temperatureafter a time delay.

Instruments and controls 67

If outside temperature drops to 3 °C,a warning message is displayed in theDriver Information Centre withUplevel-Display or Uplevel-Combi-Display.

9 Warning

The road surface may already beicy even though the displayindicates a few degrees above0 °C.

ClockDate and time are shown in theInfo-Display.

Set date and timePress the CONFIG button. The menuSettings is displayed.Select Time & Date.

Selectable setting options:■ Set time: Changes the time shown

on the display.■ Set date: Changes the date shown

on the display.■ Set time format: Changes

indication of hours between 12hours and 24 hours.

■ Set date format: Changesindication of date between MM/DD/YYYY and DD.MM.YYYY.

■ Display digital clock: Switches on/off indication of time on the display.

■ RDS clock synchronization: TheRDS signal of most VHFtransmitters automatically sets thetime. RDS time synchronisationcan take a few minutes. Sometransmitters do not send a correcttime signal. In such cases, it isrecommended to switch offautomatic time synchronisation.

Vehicle personalisation 3 92.

68 Instruments and controls

Power outlets

A 12 Volt power outlet is located in thefront console.

A further 12 Volt power outlet islocated in the rear console. Fold thecover downwards.Do not exceed the maximum powerconsumption of 120 watts.With ignition off, the power outlets aredeactivated. Additionally the poweroutlets are deactivated in the event oflow battery voltage.Electrical accessories that areconnected must comply with theelectromagnetic compatibilityrequirements laid down inDIN VDE 40 839.Do not connect any current-deliveringaccessories, e.g. electrical chargingdevices or batteries.Do not damage the outlet by usingunsuitable plugs.Stop-start system 3 121.

Cigarette lighter

The cigarette lighter is located in thefront console.Press in cigarette lighter. It switchesoff automatically once the element isglowing. Pull out lighter.

Ashtrays

Caution

To be used only for ash and not forcombustible rubbish.

Instruments and controls 69

The portable ashtray can be placed inthe cupholders.

Warning lights, gaugesand indicatorsInstrument clusterIn some versions, the needles of theinstruments briefly rotate to the endposition when the ignition is switchedon.

Speedometer

Indicates vehicle speed.

Odometer

The bottom line displays the recordeddistance in miles.

Trip odometerThe top line displays the recordeddistance since the last reset.To reset, hold the reset knobdepressed for a few seconds with theignition on.

70 Instruments and controls

Tachometer

Displays the engine speed.Drive in a low engine speed range foreach gear as much as possible.

Caution

If the needle is in the red warningzone, the maximum permittedengine speed is exceeded. Engineat risk.

Fuel gauge

Displays the fuel level in the tank.Control indicator i illuminates if thelevel in the tank is low. Refuelimmediately if it flashes.Never run the tank dry.Because of the fuel remaining in thetank, the top-up quantity may be lessthan the specified tank capacity.

Engine coolanttemperature gauge

Displays the coolant temperature.left area = engine operating

temperature not yetreached

centralarea

= normal operatingtemperature

right area = temperature too high

Instruments and controls 71

Caution

If engine coolant temperature istoo high, stop vehicle, switch offengine. Danger to engine. Checkcoolant level.

Service displayThe engine oil life system lets youknow when to change the engine oiland filter. Based on drivingconditions, the interval at which anengine oil and filter change will beindicated can vary considerably.

In the Uplevel-Display or Uplevel-Combi-Display, the remaining oil lifeduration is displayed in the VehicleInformation Menu.In the Midlevel-Display, the remainingengine oil life duration is displayed bythe control indicator I, therefore theignition must be switched on, with theengine not running.The menu and function can beselected via the buttons on the turnsignal lever.To display the remaining engine oillife duration:

Press the MENU button to select theVehicle Information Menu.Turn the adjuster wheel to selectRemaining Oil Life.The system must be reset every timethe engine oil is changed to allowproper functionality. Seek theassistance of a workshop.Press the SET/CLR button to reset.Therefore the ignition must beswitched on, with the engine notrunning.When the system has calculated thatengine oil life has been diminished,Change Engine Oil Soon or a warningcode appears in the DriverInformation Centre. Have engine oiland filter changed by a workshopwithin one week or 300 miles(whichever occurs first).Driver Information Centre 3 80.Service information 3 194.

Control indicatorsThe control indicators described arenot present in all vehicles. Thedescription applies to all instrument

72 Instruments and controls

versions. Depending on theequipment, the position of the controlindicators may vary. When theignition is switched on, most controlindicators will illuminate briefly asa functionality test.The control indicator colours mean:red = danger, important

reminderyellow = warning, information, faultgreen = confirmation of activationblue = confirmation of activationwhite = confirmation of activation

Instruments and controls 73

Control indicators in the instrument cluster

74 Instruments and controls

Control indicators in the centreconsole

Turn signalO illuminates or flashes green.

Illuminates brieflyThe parking lights are switched on.

FlashesA turn signal or the hazard warningflashers are activated.Rapid flashing: failure of a turn signallight or associated fuse, failure of turnsignal light on trailer.

Bulb replacement 3 162, Fuses3 170.Turn signals 3 104.

Seat belt reminderSeat belt reminder on frontseatsX for driver's seat illuminates orflashes red.k for front passenger seat illuminatesor flashes red, when seat is occupied.

IlluminatesAfter the ignition has been switchedon until the seat belt has beenfastened.

FlashesAfter having started the engine fora maximum of 100 seconds until theseat belt has been fastened.

Airbag and belt tensionersv illuminates red.

When the ignition is switched on, thecontrol indicator illuminates forapprox. 4 seconds. If it does notilluminate, does not extinguish after4 seconds or illuminates whilstdriving, there is a fault in the airbagsystem. Seek the assistance ofa workshop. The airbags and beltpretensioners may fail to trigger in theevent of an accident.Deployment of the belt pretensionersor airbags is indicated by continuousillumination of v.

9 Warning

Have the cause of the faultremedied immediately bya workshop.

Belt pretensioners, airbag system3 39, 3 41.

Airbag deactivationV illuminates yellow.The front passenger airbag isactivated.

Instruments and controls 75

* illuminates yellow.The front passenger airbag isdeactivated 3 44.

9 Danger

Risk of fatal injury for a child usinga child restraint system togetherwith activated front passengerairbag.Risk of fatal injury for an adultperson with deactivated frontpassenger airbag.

Charging systemp illuminates red.Illuminates when the ignition isswitched on and extinguishes shortlyafter the engine starts.

Illuminates when the engine isrunningStop, switch off engine. Battery is notcharging. Engine cooling may beinterrupted. The brake servo unit maycease to be effective. Seek theassistance of a workshop.

Malfunction indicator lightZ illuminates or flashes yellow.Illuminates when the ignition isswitched on and extinguishes shortlyafter the engine starts.

Illuminates when the engine isrunningFault in the emission control system.The permitted emission limits may beexceeded. Seek the assistance ofa workshop immediately.

Flashes when the engine isrunningFault that could lead to catalyticconverter damage. Ease up on theaccelerator until the flashing stops.Seek the assistance of a workshopimmediately.

Service vehicle soong illuminates yellow.Additionally a warning message ora warning code is displayed.The vehicle needs a service.

Seek the assistance of a workshop.Vehicle messages 3 85.

Brake and clutch systemBrake and clutch fluid level& illuminates red.The brake and clutch fluid level is toolow 3 158.

9 Warning

Stop. Do not continue yourjourney. Consult a workshop.

Illuminates after the ignition isswitched on if the manual parkingbrake is applied 3 130.

Operate pedal- illuminates or flashes yellow.Clutch pedal needs to be operated tostart the engine. Stop-start system3 121.

76 Instruments and controls

IlluminatesBrake pedal needs to be operated torelease the electrical parking brake3 130.

FlashesClutch pedal needs to be operated tostart the engine 3 119.

Electrical parking brakem illuminates or flashes red.

IlluminatesElectrical parking brake is applied3 130.

FlashesElectrical parking brake is not fullyapplied or released. Switch onignition, depress brake pedal andattempt to reset the system by firstreleasing and then applying theelectrical parking brake. If m remainsflashing, do not drive and seek theassistance of a workshop.

Electrical parking brakefaultj illuminates or flashes yellow.

IlluminatesElectrical parking brake is operatingwith degraded performance 3 130.

FlashesElectrical parking brake is in servicemode. Stop vehicle, apply andrelease the electrical parking brake toreset.

9 Warning

Have the cause of the faultremedied immediately bya workshop.

Antilock brake system(ABS)u illuminates yellow.Illuminates for a few seconds after theignition is switched on. The system isready for operation when the controlindicator extinguishes.

If the control indicator does notextinguish after a few seconds, or if itilluminates while driving, there isa fault in the ABS. The brake systemremains operational but without ABSregulation.Antilock brake system 3 129.

Upshift[ illuminates green, or is shown asa symbol in the Driver InformationCentre with Uplevel-Display orUplevel-Combi-Display.Upshifting is recommended for fuelsaving.

Power steeringc illuminates yellow.

Illuminates with power steeringreducedPower steering is reduced due tooverheating of the system. Controlindicator extinguishes when thesystem has cooled down.Stop-start system 3 121.

Instruments and controls 77

Illuminates with power steeringdisabledFailure in the power steering system.Consult a workshop.

Lane departure warning) illuminates green or yellow orflashes yellow.

Illuminates greenSystem is switched on and ready tooperate.

Illuminates yellowNo lane marking is detected.

Flashes yellowSystem recognizes an unintendedlane change.

Ultrasonic parking assistr illuminates yellow.Fault in systemorFault due to sensors that are dirty orcovered by ice or snow

orInterference due to external sourcesof ultrasound. Once the source ofinterference is removed, the systemwill operate normally.Have the cause of the fault in thesystem remedied by a workshop.Ultrasonic parking assist 3 138.

Electronic Stability Controloffn illuminates yellow.The system is deactivated.

Electronic Stability Controland Traction Controlsystemb illuminates or flashes yellow.

IlluminatesA fault in the system is present.Continued driving is possible. Drivingstability, however, may deterioratedepending on road surfaceconditions.

Have the cause of the fault remediedby a workshop.

FlashesThe system is actively engaged.Engine output may be reduced andthe vehicle may be brakedautomatically to a small degree.Electronic Stability Control 3 132,Traction Control system 3 132.

Traction Control system offk illuminates yellow.The system is deactivated.

Preheating! illuminates yellow.Preheating is activated. Onlyactivates when outside temperatureis low.

Diesel particle filter% illuminates or flashes yellow.The diesel particle filter requirescleaning.

78 Instruments and controls

Continue driving until %extinguishes. If possible, do not allowengine speed to drop below2000 rpm.

IlluminatesThe diesel particle filter is full. Startcleaning process as soon aspossible.

FlashesThe maximum filling level of the filteris reached. Start cleaning processimmediately to avoid damage to theengine.Diesel particle filter 3 123, Stop-startsystem 3 121.

Tyre pressure monitoringsystemw illuminates or flashes yellow.

IlluminatesTyre pressure loss. Stop immediatelyand check tyre pressure.

FlashesFault in system or tyre withoutpressure sensor mounted (e.g. sparewheel). After 60-90 seconds thecontrol indicator illuminatescontinuously. Consult a workshop.

Engine oil pressureI illuminates red.Illuminates when the ignition isswitched on and extinguishes shortlyafter the engine starts.

Illuminates when the engine isrunning

Caution

Engine lubrication may beinterrupted. This may result indamage to the engine and/orlocking of the drive wheels.

1. Depress clutch.2. Select neutral gear, set selector

lever to N.

3. Move out of the flow of traffic asquickly as possible withoutimpeding other vehicles.

4. Switch off ignition.

9 Warning

When the engine is off,considerably more force is neededto brake and steer. During anAutostop the brake servo unit willstill be operational.Do not remove key until vehicle isstationary, otherwise the steeringwheel lock could engageunexpectedly.

Check oil level before seeking theassistance of a workshop 3 156.

Low fueli illuminates or flashes yellow.

IlluminatesLevel in fuel tank is too low.

Instruments and controls 79

FlashesFuel used up. Refuel immediately.Never run the tank dry.Catalytic converter 3 124.Bleeding the diesel fuel system3 161.

Immobiliserd flashes yellow.Fault in the immobiliser system. Theengine cannot be started.

Reduced engine power# illuminates yellow.The engine power is limited. Consulta workshop.

Exterior light8 illuminates green.The exterior lights are on 3 97.

High beamC illuminates blue.

Illuminates when high beam is on,during headlight flash 3 98, or whenhigh beam is on with high beam assistor intelligent light range 3 100.

High beam assistl illuminates green.The high beam assist or intelligentlight range is activated 3 98,3 100.

Adaptive forward lightingf illuminates or flashes yellow.

IlluminatesFault in system.Seek the assistance of a workshop.

FlashesSystem switched to symmetrical lowbeam.Control indicator f flashes for approx.4 seconds after the ignition isswitched on as a reminder that thesystem has been activated 3 100.Automatic light control 3 98.

Fog light> illuminates green.The front fog lights are on 3 105.

Rear fog lightr illuminates yellow.The rear fog light is on 3 105.

Low washer fluidG illuminates yellow.The washer fluid level is low.Washer fluid 3 158.

Cruise controlm illuminates white or green.

Illuminates whiteThe system is on.

Illuminates greenA certain speed is stored.Cruise control 3 135.

80 Instruments and controls

Door openh illuminates red.A door or the tailgate is open.

Information displaysDriver Information Centre

The Driver Information Centre (DIC)is located in the instrument clusterbetween speedometer andtachometer. It is available asMidlevel-Display, Uplevel-Display orUplevel-Combi-Display.

In the Uplevel-Display the followingmain menus can be selected by theMenu button:■ Vehicle Information Menu■ Trip/Fuel Information Menu

Instruments and controls 81

In the Uplevel-Combi-Display, themenus can be selected by the Menubutton, indicated by symbols in thetop line of the display:X = Vehicle Information MenuW = Trip/Fuel Information Menu

Some of the displayed functions differbetween vehicle driving and standstilland some functions are only activewhen the vehicle is driving.Vehicle personalisation 3 92.Memorised settings 3 21.

Selecting menus and functionsThe menus and functions can beselected via the buttons on the turnsignal lever.

Press the MENU button to switchbetween the menus or to return froma submenu to the next higher menulevel.

Turn the adjuster wheel to highlighta menu option or to set a numericvalue.

82 Instruments and controls

Press the SET/CLR button to selecta function or to confirm a message.

Vehicle Information MenuPress the MENU button to select theVehicle Information Menu, or onUplevel-Combi-Display select X.Turn the adjuster wheel to select oneof the submenus. Press the SET/CLR button to confirm.

Follow the instructions given in thesubmenus.

Possible submenus for the followingfunctions:■ Unit: displayed units can be

changed■ Tyre Pressure: checks tyre

pressure of all wheels duringdriving 3 144

■ Remaining Oil Life: indicates whento change the engine oil andfilter3 71

■ Speed Warning: if exceeding thepreset speed, a warning chime willbe activated

■ Traffic Sign Assistant: displaysdetected traffic signs for the currentroute section 3 140

■ Following Distance Indication:displays the distance toa preceding moving vehicle3 137

Selection and indication can bedifferent between Midlevel-, Uplevel-,and Uplevel-Combi-Display.

Trip/Fuel Information MenuPress the MENU button to select theTrip/Fuel Information Menu, or selectW on Uplevel-Combi-Display.Turn the adjuster wheel to select oneof the submenus. Press the SET/CLR button to confirm.

Instruments and controls 83

■ Trip odometer 1 ■ Trip odometer 2 ■ Digital speedTrip odometer 2 and digital speed areonly available on vehicles withUplevel-Display or Uplevel-Combi-Display.On vehicles with trip computer moresubmenus are available.Trip/Fuel Information Menu, TripComputer 3 89.

Graphic-Info-Display,Colour-Info-DisplayDepending on the vehicleconfiguration the vehicle hasa Graphic- or Colour-Info-Display.The Info-Display is located in theinstrument panel above theInfotainment system.

Graphic-Info-Display

Depending on the Infotainmentsystem, the Graphic-Info-Display isavailable in two versions.

Graphic-Info-Display indicates:■ time 3 67■ outside temperature 3 66■ date 3 67■ Infotainment system, see

description in the Infotainmentsystem manual

■ settings for vehicle personalisation3 92

84 Instruments and controls

Colour-Info-Display

The Colour-Information-Displayindicates in colour:■ time 3 67■ outside temperature 3 66■ date 3 67■ Infotainment system, see

description in the Infotainmentsystem manual

■ navigation, see description in theInfotainment system manual

■ system settings

■ vehicle messages 3 85■ settings for vehicle personalisation3 92

The type of information and how it isdisplayed depends on the equipmentof the vehicle and the settings made.

Selecting menus and settingsMenus and settings are accessed viathe display.

Selections are made via:■ menus■ function buttons and multifunction

knob of the Infotainment system

Selecting with the Infotainmentsystem

Select a function via the Infotainmentsystem buttons. The menu of theselected function is displayed.The multifunction knob is used toselect an item and to confirm.

Multifunction knobThe multifunction knob is the centralcontrol element for the menus:Turn■ To mark a menu option■ To set a numeric value or to display

a menu option

Instruments and controls 85

Press (the outer ring)■ To select or activate the marked

option■ To confirm a set value■ To switch a system function on/offBACK buttonPress button to:■ exit a menu without changing

settings■ return from a submenu to a higher

menu level■ delete the last character in

a character sequencePress and hold the button for a fewseconds to delete the entire entry.Vehicle personalisation 3 92.Memorised settings 3 21.

Vehicle messagesMessages are indicated mainly in theDriver Information Centre (DIC), insome cases together with a warningand signal buzzer.

Press the SET/CLR button, theMENU button or turn the adjusterwheel to confirm a message.

Vehicle messages on theMidlevel-Display

The vehicle messages are displayedas code numbers.

No. Vehicle message

2 No radio remote controldetected, depress clutch pedalfor a restart

3 Engine coolant level low

4 Air conditioning off

5 Steering wheel is locked

86 Instruments and controls

No. Vehicle message

6 Depress brake pedal to releaseelectrical parking brake

7 Turn steering wheel, switchignition off and then on

9 Turn steering wheel, startengine again

12 Vehicle overloaded

13 Compressor overheated

15 Centre high-mounted brakelight failure

16 Brake light failure

17 Headlight levelling malfunction

18 Left low beam failure

19 Rear fog light failure

20 Right low beam failure

21 Left sidelight failure

22 Right sidelight failure

23 Reversing light failure

No. Vehicle message

24 Number plate light failure

25 Left front turn signal failure

26 Left rear turn signal failure

27 Right front turn signal failure

28 Right rear turn signal failure

29 Check trailer brake light

30 Check trailer reversing light

31 Check left trailer turn signal

32 Check right trailer turn signal

33 Check trailer rear fog light

34 Check trailer rear light

35 Replace battery in radio remotecontrol

48 Clean side blind zone alertsystem

49 Lane departure warningunavailable

No. Vehicle message

50 Activated pedestrian protectionsystem, reset bonnet

53 Tighten gas cap

54 Water in diesel fuel filter

55 Diesel particle filter is full3 123

56 Tyre pressure imbalance onfront axle

57 Tyre pressure imbalance onrear axle

58 Tyres without TPMS sensorsdetected

59 Open and then close driverwindow

60 Open and then close frontpassenger window

61 Open and then close rear leftwindow

62 Open and then close rear rightwindow

Instruments and controls 87

No. Vehicle message

65 Theft attempted

66 Service theft alarm system

67 Service steering wheel lock

68 Service power steering

69 Service suspension system

70 Service level control system

71 Service rear axle

74 Service AFL

75 Service air conditioning

76 Service side blind zone alertsystem

77 Service lane departure warning

78 Service pedestrian protectionsystem

79 Top up engine oil

81 Service transmission

82 Change engine oil soon

No. Vehicle message

83 Service adaptive cruise control

84 Engine power is reduced

94 Shift to park before exiting

95 Service airbag

128 Bonnet open

134 Park assist fault, clean bumper

136 Service parking assist

145 Check washer fluid level

174 Low battery

258 Park assist off

Vehicle messages on theUplevel-Display or Uplevel-Combi-Display

The vehicle messages are displayedas text. Follow the instructions givenin the messages.The system displays messagesregarding the following topics:■ Fluid levels■ Anti-theft alarm system■ Brakes■ Drive systems■ Ride control systems

88 Instruments and controls

■ Cruise control■ Object detection systems■ Lighting, bulb replacement■ Wiper/washer system■ Doors, windows■ Radio remote control■ Seat belts■ Airbag systems■ Engine and transmission■ Tyre pressure■ Diesel particle filter■ Battery

Vehicle messages on theColour-Info-DisplaySome important messages appearadditionally in theColour-Info-Display. Press themultifunction knob to confirma message. Some messages onlypop up for a few seconds.

Warning chimesWhen starting the engine orwhilst drivingOnly one warning chime will sound ata time.The warning chime regardingunfastened seat belts has priorityover any other warning chime.■ If seat belt is not fastened.■ If a door or the tailgate is not fully

closed when starting off.■ If a certain speed is exceeded with

parking brake applied.■ If a programmed speed or speed

limit is exceeded.■ If a warning message or a warning

code appears in the DriverInformation Centre.

■ If the parking assist detects anobject.

■ If unintended lane change occurs.■ If the reverse gear is engaged and

the rear end carrier extended.■ If the diesel particle filter has

reached the maximum filling level.

When the vehicle is parked and/or the driver's door is opened■ When the key is in the ignition

switch.■ With exterior lights on.

During an Autostop■ If the driver's door is opened.

Battery voltageWhen the battery voltage is runninglow, a warning message or warningcode 174 will appear in the DriverInformation Centre.1. Switch off immediately electrical

consumers which are not requiredfor a safe ride, such as seatheating, heated rear window orother main consumers.

2. Charge the battery by drivingcontinuously for a while or byusing a charging device.

The warning message or warningcode will disappear after the enginehas been started two timesconsecutively without voltage drop.

Instruments and controls 89

If the battery cannot be recharged,have the cause of the fault remediedby a workshop.

Trip computerThe menus and functions can beselected via the buttons on the turnsignal lever.

Press the MENU button to select theTrip/Fuel Information Menu, or selectW on the Uplevel-Combi-Display.

Trip/Fuel Information Menu onUplevel-DisplayTurn the adjuster wheel to select oneof the submenus:

90 Instruments and controls

■ Trip odometer 1■ Trip odometer 2■ Range■ Average consumption■ Instantaneous consumption■ Average speed■ Digital speedTrip/Fuel Information Menu onUplevel-Combi-DisplayTurn the adjuster wheel to select thesubmenus:

■ Trip odometer 1■ Average consumption■ Average speed

■ Trip odometer 2■ Average consumption■ Average speed

■ Digital speed■ Range■ Instantaneous consumption

Trip computer 1 and 2The information of the two tripcomputers can be reset separately ineach mode, making it possible todisplay different trip distances.To reset, press the reset knob orpress the SET/CLR button for a fewseconds.

Instruments and controls 91

Trip odometerTrip odometer displays the recordeddistance since a certain reset. Twotrip odometers which recordsseparately are selectable.

RangeRange is calculated from current fueltank content and currentconsumption. The display showsaverage values.After refuelling, the range is updatedautomatically after a brief delay.

When the fuel level in the tank is low,a message appears on vehicles withUplevel-Display or Uplevel-Combi-Display.When the tank has to be refuelledimmediately, a warning code orwarning message is displayed onvehicles with Midlevel- and Uplevel-Display or Uplevel-Combi-Display.Additionally the control indicator i inthe fuel gauge illuminates or flashes3 78.

Average consumptionDisplay of average consumption. Themeasurement can be reset at anytime and starts with a default value.To reset, press the SET/CLR buttonfor a few seconds.

Instantaneous consumptionDisplay of the instantaneousconsumption.

Average speedDisplay of average speed. Themeasurement can be reset at anytime.

To reset, press the SET/CLR buttonfor a few seconds.

Digital speedDigital display of the instantaneousspeed.

92 Instruments and controls

Vehicle personalisationThe vehicle's behaviour can bepersonalised via changing thesettings in the Info-Display.Some of the personal settings fordifferent drivers can be memorisedindividually for each vehicle key.Memorised settings 3 21.Depending on vehicle equipment andcountry-specific regulations some ofthe functions described below mightnot be available.Some functions are only displayed oractive when the engine is running.

Personal settings in theGraphic-Info-Display

Press the CONFIG button. The menuSettings is displayed.

The following settings can beselected by turning and pressing themultifunction knob:■ Sport mode settings■ Languages■ Time Date■ Radio settings■ Phone settings■ Vehicle settingsIn the corresponding submenus thefollowing settings can be changed:

Instruments and controls 93

Sport mode settingsThe driver can select the functionswhich will be activated in Sport mode3 133.■ Sport suspension: Damping

becomes harder.■ Sport powertrain performance:

Accelerator pedal and gear changecharacteristics become moreresponsive.

■ Sport steering: Steering support isreduced.

■ Swap backlight colour main instr.:Change of instrument illuminationcolour.

LanguagesSelection of the desired language.

Time DateSee Clock 3 67.

Radio settingsSee description for Infotainmentsystem in the Infotainment systemmanual.

Phone settingsSee description for Infotainmentsystem in the Infotainment systemmanual.

Vehicle settings

■ Climate and air qualityAuto fan speed: Modifies the fanregulation. Changed setting will beactive after switching the ignition offand on again.Climate control mode: Activates ordeactivates the cooling every timethe ignition is switched on or usesthe last chosen setting.

Auto demist: Supports windscreendehumidification by automaticallyselecting the necessary settingsand auto air conditioning mode.Auto rear demist: Activatesautomatically rear heated window.

■ Comfort settingsChime volume: Changes thevolume of warning chimes.Personalisation by driver: Activatesor deactivates the personalisationfunction.Rear auto wipe in reverse:Activates or deactivatesautomatically switching on of the

94 Instruments and controls

rear window wiper when reversegear is engaged.

■ Park assist / Collision detectionPark assist: Activates ordeactivates the ultrasonic parkingassist.

■ Exterior ambient lightingDuration upon exit of vehicle:Activates or deactivates andchange the duration of exit lighting.Exterior lighting by unlocking:Activates or deactivates thewelcome lighting.

■ Power door locksAuto door unlock: Activates ordeactivates the automatic doorunlocking function after switchingoff ignition.Auto door lock: Activates ordeactivates the automatic doorlocking function after driving off.Stop door lock if door open:Activates or deactivates theautomatic door locking functionwhile a door is open.

Delayed door lock: Activates ordeactivates the delayed doorlocking function.

■ Remote locking, unlocking, startingRemote unlock feedback: Activatesor deactivates the hazard warningflasher feedback whilst unlocking.Remote door unlock: Changes theconfiguration to unlock only thedriver's door or the whole vehiclewhilst unlocking.Auto relock doors: Activates ordeactivates the automatic relockfunction after unlocking withoutopening the vehicle.

■ Restore factory settingsRestore factory settings: Reset allsettings to the default settings.

Personal settings in theColour-Info-Display

Press the CONFIG button. The menuSettings is displayed.

Instruments and controls 95

The following settings can beselected by turning and pressing themultifunction knob:■ Sport mode settings■ Languages■ Time & Date■ Radio settings■ Phone settings■ Navigation settings■ Vehicle settings■ Display settingsIn the corresponding submenus thefollowing settings can be changed:

Sport mode settingsThe driver can select the functionswhich will be activated in Sport mode3 133.■ Sport suspension: Damping

becomes harder.■ Sport powertrain performance:

Accelerator pedal and gear changecharacteristics become moreresponsive.

■ Sport steering: Steering support isreduced.

■ Swap backlight colour main instr.:Change of instrument illuminationcolour.

LanguagesSelection of the desired language.

Time & DateSee Clock 3 67.

Radio settingsSee description for Infotainmentsystem in the Infotainment systemmanual.

Phone settingsSee description for Infotainmentsystem in the Infotainment systemmanual.

Navigation settingsSee description for Infotainmentsystem in the Infotainment systemmanual.

Vehicle settings

■ Climate and air qualityAuto fan speed: Modifies the fanregulation. Changed setting will beactive after switching the ignition offand on again.

96 Instruments and controls

Climate control mode: Activates ordeactivates cooling when switchingon the ignition or uses the lastchosen setting.Auto demist: Supports windscreendehumidification by automaticallyselecting the necessary settingsand auto air conditioning mode.Auto rear demist: Activatesautomatically the rear heatedwindow.

■ Comfort settingsChime volume: Changes thevolume of warning chimes.

Rear auto wipe in reverse:Activates or deactivatesautomatically switching on of therear window wiper when reversegear is engaged.

■ Park assist / Collision detectionPark assist: Activate or deactivatethe ultrasonic parking assist.

■ Exterior ambient lightingDuration upon exit of vehicle:Activates or deactivates andchanges the duration of exitlighting.Exterior lighting by unlocking:Activates or deactivates thewelcome lighting.

■ Power door locksAuto door unlock: Activates ordeactivates the automatic doorunlocking function after switchingoff ignition.Auto door lock: Activates ordeactivates the automatic doorlocking function after driving off.Prevent doorlock while door open:Activates or deactivates the

automatic door locking functionwhile a door is open.

■ Lock / Unlock / Start by remoteRemote unlock feedback: Activatesor deactivates the hazard warningflasher feedback whilst unlocking.Remote door unlock: Changes theconfiguration to unlock only thedriver's door or the whole vehiclewhilst unlocking.Auto relock doors: Activates ordeactivates the automatic relockfunction after unlocking withoutopening the vehicle.

■ Restore factory settingsRestore factory settings: Resets allsettings to the default settings.

Display settingsSelectable display settings:■ Day mode: Optimisation for

daylight conditions.■ Night mode: Optimisation for

darkness.■ Automatic mode: The display

changes mode when the vehiclelights are switched on/off.

Lighting 97

Lighting

Exterior lighting ............................ 97Interior lighting ........................... 106Lighting features ........................ 107

Exterior lightingLight switchTurn light switch:

7 = lights off8 = sidelights9 = headlights

Control indicator 8 3 79.

Light switch with Automatic lightcontrol

Turn light switch:AUTO = automatic light control:

Headlights are switchedon and off automaticallydepending on externallighting conditions.

m = activation or deactivationof the automatic lightcontrol. Switch turns backto AUTO.

8 = sidelights9 = headlights

98 Lighting

In the Driver Information Centre withUplevel-Display or Uplevel-Combi-Display, the current status of theautomatic light control is displayed.When switching on the ignition,automatic light control is active.When headlights are on, 8 lights up.Control indicator 8 3 79.

Tail lightsTail lights are illuminated togetherwith headlights and sidelights.

Automatic light control

When the automatic light controlfunction is switched on and theengine is running, the systemswitches between daytime runninglight and headlights automaticallydepending on the lighting conditionsand information given by the rainsensor system.

Daytime running lightDaytime running light increasesvisibility of the vehicle during daylight.

Automatic headlight activationDuring poor lighting conditions theheadlights are switched on.Furthermore the headlights areswitched on if the windscreen wipershave been activated for severalwipes.

Tunnel detectionWhen a tunnel is entered theheadlights are switched on withoutany delay.Adaptive forward lighting 3 100.

High beam

To switch from low to high beam,push lever.To switch to low beam, push leveragain or pull.

High beam assistThis feature allows high beam asmain driving light by night and whenvehicle speed is faster than 25 mph.

Lighting 99

It switches to low beam when:■ the camera in the windscreen

detects the lights of oncoming orpreceding vehicles

■ the vehicle speed is slower than12 mph

■ it is foggy or snowy■ driving in urban areasIf there are no restrictions detected,the system switches back to highbeam.

Activation

The high beam assist is activated bypushing the indicator lever twice witha speed above 25 mph.The green control indicator lilluminates continuously when theassist is activated, the blue one 7illuminates when high beam is on.Control indicator l 3 79.

DeactivationPush indicator lever once. It is alsodeactivated when front fog lights areswitched on.If a headlight flash is activated whenthe high beam is on, the high beamassist will be deactivated.If a headlight flash is activated whenthe high beam is off, the high beamassist will stay activated.The latest setting of the high beamassist will remain after the ignition isswitched on again.

Headlight flashTo activate the headlight flash, pulllever.

Headlight rangeadjustmentManual headlight rangeadjustment

To adapt headlight range to thevehicle load to prevent dazzling: turnthumb wheel ? to required position.0 = front seats occupied1 = all seats occupied2 = all seats occupied and load

compartment laden3 = driver's seat occupied and load

compartment laden.

100 Lighting

Dynamic automatic headlightlevelling 3 100.

Headlights when drivingabroadThe asymmetrical headlight beamextends visibility at the edge of theroad at the passenger side.However, when driving in countrieswhere traffic drives on the oppositeside of the road, adjust the headlightsto prevent dazzling of oncomingtraffic.

Vehicles with halogen headlightsystemThe headlights do not have to beadjusted.

Vehicles with Xenon headlightsystem

1. Key in ignition switch.2. Pull turn signal lever and hold

(headlight flash).3. Switch on ignition.4. After approx. 5 seconds the

control indicator f starts flashingand an acoustic signal sounds.

Control indicator f 3 79.Every time the ignition is switched on,f flashes as a reminder for approx.4 seconds.

For deactivation operate the sameprocedure as described above. f willnot flash when function isdeactivated.

Adaptive forward lightingThe Adaptive forward lightingfunctions are only available with Bi-Xenon headlights. Light range, lightdistribution and intensity of light arevariably triggered depending on thelight conditions, weather and roadtype.With the light switch in positionAUTO all lighting functions areavailable.The following functions are availablealso with light switch in position 9:■ Dynamic curve lighting■ Cornering light■ Reversing function■ Dynamic automatic headlight

levelling

Lighting 101

Playstreet lightingActivated automatically at low speedup to approx. 20 mph. The light beamis turned at an angle of 8° to theroadside.

Town lightingActivated automatically at a speedrange between approx. 25 and34 mph and when street lights aredetected by the light sensor. The lightrange is reduced by an extended lightdistribution.

Country lightingActivated automatically at a speedrange between approx. 34 and70 mph. The beam of light and thebrightness is different between theleft and the right side.

Motorway lightingActivated automatically at a speedabove approx. 70 mph and minimalsteering movements. It switches onafter a delay or directly when thevehicle is powerfully accelerated. Thelight beam is longer and brighter.

Adverse weather lightingActivated automatically up to a speedof approx. 43 mph, when the rainsensor recognises condensation orthe wiper operates continuously. Therange, distribution and light intensityis regulated variably depending onvisibility.

Dynamic curve lighting

The light beam pivots based onsteering wheel angle and speed,improving lighting in curves.Control indicator f 3 79.

Cornering light

On tight bends or when turning off,depending on the steering angle orthe turn signal light, an additional leftor right reflector is switched on whichilluminates the road at an right angleto the direction of travel. It is activatedup to a speed of 25 mph.Control indicator f 3 79.

Reversing functionIf the headlights are on and reversegear is engaged, both corner lightsare switched on. They remainilluminated for 20 seconds afterdisengaging reverse gear or untildriving faster than 10 mph ina forward gear.

102 Lighting

High beam assistThis feature allows high beam asmain driving light by night and whenvehicle speed is faster than 25 mph.It switches to low beam when:■ the camera in the windscreen

detects the lights of oncoming orpreceding vehicles

■ the vehicle speed is slower than12 mph

■ it is foggy or snowy■ driving in urban areasIf there are no restrictions detected,the system switches back to highbeam.

Activation

The high beam assist is activated bypushing the indicator lever twice witha speed above 25 mph.The green control indicator lilluminates continuously when theassist is activated, the blue one 7illuminates when high beam is on.Control indicator l 3 79.

DeactivationPush indicator lever once. It is alsodeactivated when front fog lights areswitched on.

If a headlight flash is activated whenthe high beam is on, the high beamassist will be deactivated.If a headlight flash is activated whenthe high beam is off, the high beamassist will stay activated.The latest setting of the high beamassist will remain after the ignition isswitched on again.

Intelligent light ranging withautomatic high beam activationIntelligent light ranging uses theproperties of Bi-Xenon headlights toextend the light range of the lowbeams up to 1312 ft and activatesadditionally automatic high beamwithout dazzling or disturbingoncoming as well as preceding traffic.High beam will be deactivated and thelow beam light range will be reducedto non dazzling when the followingrestrictions are detected by the frontcamera in the windscreen:■ a preceding vehicle is recognised,■ an oncoming vehicle is recognised,

Lighting 103

■ urban areas are entered,■ it is foggy or snowy.If there are no restrictions detected,the system switches back to highbeam.When the system is active, the frontcamera always monitors the areaahead of your vehicle and regulatespermanently an optimally light spreadfor a maximum driver vision undernearly all conditions.Thereby Intelligent light ranging withautomatic high beam activationreduces the difference betweenconventional low and high beamwithout drastic changes in light-range, distribution and intensity.

A special topographical evaluationfunction detects preceding vehicleson hills or slopes by recognising therear light moving ahead. The systemadjusts the height of the light range toensure optimal illumination on theroad ahead without dazzling.

Activation

Intelligent light ranging and automatichigh beam activation both areswitched on together by pushing theindicator lever twice. They can beswitched on with ignition on.Automatic high beam activationoperates at a speed above 25 mphand deactivates below 12 mph.Intelligent light ranging operatesabove 35 mph.

104 Lighting

The green control indicator lilluminates continuously when thefunction is activated, the blue one 7illuminates when high beam switcheson automatically.

DeactivationPush indicator lever once. It is alsodeactivated when front fog lights areswitched on.

Dynamic automatic headlightlevellingTo prevent oncoming traffic fromdazzle, headlight levelling isautomatically adjusted based oninclination information measured byfront and rear axle, acceleration ordeceleration and vehicle speed.

Fault in Adaptive forwardlighting systemWhen the system detects a failure inthe Adaptive forward lighting system,the system moves to a preset positionto avoid dazzling of oncoming traffic.If this is not possible the affectedheadlight will be automaticallyswitched off. In any case oneheadlight will stay on. A warning isdisplayed in the Driver InformationCentre.

Hazard warning flashers

Operated with the ¨ button.

In the event of an accident with airbagdeployment the hazard warningflashers are activated automatically.

Turn and lane-changesignals

lever up = right turn signallever down = left turn signal

If the lever is moved past theresistance point, the turn signal isswitched on constantly. When thesteering wheel moves back, the turnsignal is automatically deactivated.

Lighting 105

For three flashes, e.g. when changinglanes, press the lever until resistanceis felt and then release.When a trailer is connected, turnsignal flashes six times whenpressing the lever until resistance isfelt and then releasing.Move the lever to the resistance pointand hold for longer indication.Switch the turn signal off manually bymoving the lever to its originalposition.

Front fog lights

Operated with the > button.

Light switch in position AUTO:switching on front fog lights will switchheadlights on automatically.

Rear fog lights

Operated with the r button.Light switch in position AUTO:switching on rear fog light will switchheadlights on automatically.Light switch in position 8: rear foglight can only be switched on withfront fog lights.The vehicle rear fog light isdeactivated when towing.

Parking lights

When the vehicle is parked, theparking lights on one side can beactivated:1. Switch off ignition.2. Move turn signal lever all the way

up (right parking lights) or down(left parking lights).

Confirmed by a signal and thecorresponding turn signal controlindicator.

106 Lighting

Reversing lightsThe reversing light comes on whenthe ignition is on and reverse gear isselected.

Misted light coversThe inside of the light housing maymist up briefly in poor, wet and coldweather conditions, in heavy rain orafter washing. The mist disappearsquickly by itself; to help switch on theheadlights.

Interior lightingInstrument panelillumination control

Brightness of the following lights canbe adjusted when the exterior lightsare on:■ Instrument panel illumination■ Info-Display■ Illuminated switches and operation

elements.Turn thumb wheel A and hold untilthe desired brightness is obtained.

On vehicles with light sensor, thebrightness can only be adjusted whenthe exterior lights are on and the lightsensor detects night conditions.

Interior lightsDuring entry and exit of the vehicle,the front and rear courtesy lightsautomatically switch on and then offafter a delay.NoteIn the event of an accident withairbag deployment the courtesylights are turned on automatically.

Front courtesy light

Lighting 107

Operate rocker switch:w = automatic switching on

and off.press u = on.press v = off.

Rear courtesy lights

Illuminate in conjunction with the frontcourtesy light depending on rockerswitch position.

Reading lights

Operated with s and t buttons infront and rear courtesy lights.

Sunvisor lightsIlluminates when the cover is opened.

Lighting featuresCentre console lightingSpotlight incorporated in the interiorlighting comes on when headlightsare switched on.

Entry lightingWelcome lightingFollowing lights are switched on fora short time by unlocking the vehiclewith the radio remote control:■ headlights,■ tail lights,■ reversing lights,■ number plate lights,■ instrument panel light,■ interior lights,■ door and console lights,■ puddle lights.Some functions work only in the darkand facilitates locating the vehicle.

108 Lighting

The lighting switches off immediatelywhen the ignition key is turned toposition 1 3 119.Activation or deactivation of thisfunction can be changed in the menuSettings in the Info-Display. Vehiclepersonalisation 3 92.The settings can be saved for the keybeing used 3 21.The following lights will additionallyswitch on when the driver's door isopened:■ all switches,■ Driver Information Centre,■ door pocket lights,■ console lights.

Exit lightingThe following lights switch on if thekey is removed from the ignitionswitch:■ Interior lights■ Instrument panel light (only when it

is dark)

■ Door and console lights■ Puddle lightsThey will switch off automatically aftera delay and will be activated again ifthe driver's door is opened.Headlights, tail lights, reversing lightsand number plate lights illuminate thesurrounding area for an adjustabletime after leaving the vehicle.

Switching on

1. Switch off ignition.2. Remove ignition key.3. Open driver's door.

4. Pull turn signal lever.5. Close driver's door.

If the driver's door is not closed thelights switch off after two minutes.Exit lighting is switched offimmediately if the turn signal lever ispulled while the driver's door is open.Activation, deactivation and durationof this function can be changed in themenu Settings in the Info-Display.Vehicle personalisation 3 92.The settings can be saved for the keybeing used 3 21.

Battery dischargeprotectionBattery state of charge functionThe function guarantees longestbattery life via a generator withcontrollable power output andoptimised power distribution.To prevent discharge of the batterywhen driving, following systems arereduced automatically in two stagesand finally switched off:

Lighting 109

■ Auxiliary heater■ Heated rear window and mirrors■ Heated seats■ FanIn the second stage a message whichconfirms the activation of the batterydischarge protection will be displayedin the Driver Information Centre.

Switching off electric lightsTo prevent discharge of the batterywhen the ignition is switched off,some interior lights are switched offautomatically after some time.

110 Climate control

Climate control

Climate control systems ............. 110Air vents ..................................... 116Maintenance .............................. 117

Climate control systemsHeating and ventilationsystem

Controls for:■ Temperature■ Air distribution■ Fan speed■ Demisting and defrostingHeated rear window Ü 3 31.

Temperaturered = warmblue = cold

Heating will not be fully effective untilthe engine has reached normaloperating temperature.

Air distributions = to windscreen and front door

windowsM = to head area via adjustable air

ventsK = to foot well

All combinations are possible.

Fan speedAdjust the air flow by switching the fanto the desired speed.

Demisting and defrosting■ Press button V: fan automatically

switches to higher speed, the airdistribution is directed towards thewindscreen.

■ Set temperature control to warmestlevel.

■ Switch on heated rear window Ü.■ Open side air vents as required and

direct them towards the doorwindows.

Climate control 111

Air conditioning system

In addition to the heating andventilation system, the airconditioning system has controls for:n = cooling4 = air recirculation

Heated seats ß 3 38, Heatedsteering wheel * 3 63.

Cooling nOperated with the n button and isfunctional only when the engine andfan are running.

The air conditioning system cools anddehumidifies (dries) as soon as theoutside temperature is slightly abovethe freezing point. Thereforecondensation may form and drip fromunder the vehicle.If no cooling or drying is required,switch the cooling system off to savefuel. When the cooling system isswitched off, no engine restart will berequested by the climate controlsystem during an Autostop.

Air recirculation system 4Operated with the 4 button.

9 Warning

The exchange of fresh air isreduced in air recirculation mode.In operation without cooling the airhumidity increases, so thewindows may mist up from inside.The quality of the passengercompartment air deteriorates,which may cause the vehicleoccupants to feel drowsy.

In warm and very humid ambient airconditions, the windscreen might mistup from outside, when cold air isdirected to it. If windscreen mists upfrom outside, activate windscreenwiper and deactivate s.

Maximum coolingBriefly open the windows so that hotair can disperse quickly.■ Cooling n on.■ Air circulation system 4 on.■ Press air distribution switch M.■ Set temperature control to coldest

level.■ Set fan speed to highest level.■ Open all vents.

112 Climate control

Demisting and defrosting thewindows V

■ Press button V: fan automaticallyswitches to higher speed, the airdistribution is directed towards thewindscreen.

■ Switch cooling n on.■ Set temperature control to warmest

level.■ Switch on heated rear window Ü.■ Open side air vents as required and

direct them towards the doorwindows.

NoteIf the settings for demisting anddefrosting are selected, an Autostopwill be inhibited.If the settings for demisting anddefrosting are selected while theengine is in an Autostop, the enginewill restart automatically.

Electronic climate controlsystemThe dual zone climate control allowsdifferent climatisation temperaturesfor driver and front passenger side.

Controls for:■ Temperature on driver side■ Air distribution■ Fan speed■ Temperature on front passenger

siden = coolingAUTO = automatic mode4 = manual air recirculationV = demisting and defrosting

Heated rear window Ü 3 31, Heatedseats ß 3 38, Heated steering wheel* 3 63.The preselected temperature isautomatically regulated. In theautomatic mode the fan speed and airdistribution automatically regulate theair flow.The system can be manually adaptedvia the use of air distribution and airflow controls.

Climate control 113

Each change of settings is shown inthe Info-Display for a few seconds.The electronic climate control systemis only fully operational when theengine is running.

Automatic mode AUTO

Basic setting for maximum comfort:■ Press AUTO button, the air

distribution and fan speed areregulated automatically.

■ Open all air vents.■ Press n to switch on cooling. On

some versions cooling is activatedautomatically by pressing AUTObutton.

■ Set the preselected temperaturesfor driver and front passenger usingthe left and right rotary knob to22 °C.

The fan speed regulation in automaticmode can be changed in the menuSettings.Vehicle personalisation 3 92.All air vents are actuatedautomatically in automatic mode. Theair vents should therefore always beopen.

Temperature preselectionTemperatures can be set to thedesired value.

If the minimum temperature is set, theclimate control system runs atmaximum cooling.

114 Climate control

If the maximum temperature is set,the climate control system runs atmaximum heating.NoteIf the temperature is reduced 2 °C ormore while the engine is in anAutostop, the engine will restartautomatically.Stop-start system 3 121.

Demisting and defrosting thewindows V■ Press button V.■ Press cooling button n.■ Temperature and air distribution

are set automatically and the fanruns at high speed.

■ Switch on heated rear window Ü.■ To return to automatic mode: press

button V or AUTO.

NoteIf the V button is pressed while theengine is running, an Autostop willbe inhibited until the V button ispressed again.If the V button is pressed while theengine is in an Autostop, the enginewill restart automatically.

Manual settingsClimate control system settings canbe changed by activating the buttonsand rotary knobs as follows.Changing a setting will deactivate theautomatic mode.

Fan speed Z

Press lower button to decrease orupper button to increase fan speed asshown in the illustration. The fanspeed is indicated by the number ofsegments in the display.Pressing the lower button longer: fanand cooling are switched off.Pressing the upper button longer: thefan runs at maximum speed.To return to automatic mode: PressAUTO button.

Air distribution s, M, KPress accordant button for desiredadjustment. Activation is indicated bythe LED in the button.s = to windscreen and front door

windows.M = to head area via adjustable air

vents.K = to foot well.

All combinations are possible.Return to automatic air distribution:Deactivate corresponding setting orpress button AUTO.

Climate control 115

Cooling nActivate or deactivate with the nbutton.The air conditioning system cools anddehumidifies (dries) when outsidetemperature is above a specific level.Therefore condensation may formand drip from under the vehicle.If no cooling or drying is required,switch the cooling system off to savefuel. When the cooling system isswitched off, no engine restart will berequested by the climate controlsystem during an Autostop.The display will indicate ACON whencooling is activated or ACOFF whenthe cooling is deactivated.

Air recirculation mode 4

9 Warning

The exchange of fresh air isreduced in air recirculation mode.In operation without cooling the airhumidity increases, so thewindows may mist up from inside.The quality of the passengercompartment air deteriorates,which may cause the vehicleoccupants to feel drowsy.

In warm and very humid ambient airconditions, the windscreen might mistup from outside, when cold air isdirected to it. If windscreen mists upfrom outside, activate windscreenwiper and deactivate s.

Press button 4 once to activate themanual air recirculation mode.Activation is indicated by the LED inthe button.

Basic settingsSome settings can be changed in themenu Settings in the Info-Display.Vehicle personalisation 3 92.

116 Climate control

Auxiliary heaterAir heaterQuickheat is an electric auxiliary airheater which automatically warms upthe passenger compartment morequickly.

Air ventsAdjustable air ventsAt least one air vent must be openwhile the cooling is on.

To open the vent, turn the adjusterwheel towards the bigger W symbol.Adjust the air amount at the ventoutlet by turning the adjuster wheel.

Direct the flow of air by tilting andswivelling the slats.To close the vent, turn the adjusterwheel towards the smaller W symbol.

9 Warning

Do not attach any objects to theslats of the air vents. Risk ofdamage and injury in case of anaccident.

Fixed air ventsAdditional air vents are locatedbeneath the windscreen and doorwindows and in the foot wells.

Climate control 117

MaintenanceAir intake

The air intake in front of thewindscreen in the enginecompartment must be kept clear toallow air intake. Remove any leaves,dirt or snow.

Pollen filterThe pollen filter cleans dust, soot,pollen and spores from the airentering the vehicle through the airintake.

Air conditioning regularoperationIn order to ensure continuouslyefficient performance, cooling mustbe operated for a few minutes oncea month, irrespective of the weatherand time of year. Operation withcooling is not possible when theoutside temperature is too low.

ServiceFor optimal cooling performance, it isrecommended to annually check theclimate control system, startingthree years after initial vehicleregistration, including:■ Functionality and pressure test■ Heating functionality■ Leakage check■ Check of drive belts■ Cleaning of condenser and

evaporator drainage■ Performance check

118 Driving and operating

Driving and operating

Driving hints ............................... 118Starting and operating ............... 119Engine exhaust .......................... 123Automatic transmission .............. 125Manual transmission .................. 128Brakes ........................................ 129Ride control systems ................. 132Driver assistance systems ......... 135Fuel ............................................ 146Towing ....................................... 149

Driving hintsControl of the vehicleNever coast with engine notrunning (except duringAutostop)Many systems will not function in thissituation (e.g. brake servo unit, powersteering). Driving in this manner isa danger to yourself and others. Allsystems function during an Autostop,but there will be a controlled reductionin power steering assist and vehiclespeed is reduced.Stop-start system 3 121.

Idle boostIf charging of the battery is requireddue to battery condition, the poweroutput of the generator has to beincreased. This will be achieved by anidle boost which may be audible.On vehicles with Uplevel-Display orUplevel-Combi-Display, a messageappears in the Driver InformationCentre.

PedalsTo ensure the pedal travel isuninhibited, there must be no mats inthe area of the pedals.

Driving and operating 119

Starting and operatingNew vehicle running-inDo not brake unnecessarily hard forthe first few journeys.During the first drive, smoke mayoccur because of wax and oilevaporating off the exhaust system.Park the vehicle in the open fora while after the first drive and avoidinhaling the fumes.During the running-in period fuel andengine oil consumption may behigher and the cleaning process ofthe diesel particle filter may takeplace more often. Autostop may beinhibited to allow for charging thebattery.Diesel particle filter 3 123.

Ignition switch positions

0 = Ignition off1 = Steering wheel lock released,

ignition off2 = Ignition on, for diesel engine:

preheating3 = Starting

Retained power offThe following electronic systems canwork until the driver's door is openedor at the latest for 10 minutes after theignition is switched off:

■ Power windows■ Power outletsPower to the Infotainment system willcontinue to operate for 30 minutes oruntil the key is removed from theignition switch, regardless of whetherany door will be opened.

Starting the engine

Manual transmission: operate clutch.Automatic transmission: operatebrake and move the selector lever toP or N.Do not operate the accelerator pedal.

120 Driving and operating

Diesel engine: turn the key to position2 for preheating until controlindicator ! extinguishes.Turn the key briefly to position 3 andrelease: an automatic procedureoperates the starter with a short delayas long as the engine is running, seeAutomatic Starter Control.Before restarting or to switch off theengine, turn the key back to position0.During an Autostop, the engine canbe started by depressing the clutchpedal.

Starting the vehicle at lowtemperaturesThe start of the engine withoutadditional heaters is possible down to-25 °С for diesel engines and -30 °Cfor petrol engines. Required is anengine oil with the correct viscosity,the correct fuel, performed servicesand a sufficiently charged battery.With temperatures below -30 °C theautomatic transmission needa warming phase of approx.5 minutes. The selector lever must bein position P.

Automatic Starter ControlThis function controls the enginestarting procedure. The driver doesnot have to hold the key in position3. Once applied, the system will go onstarting automatically until the engineis running. Because of the checkingprocedure, the engine starts runningafter a short delay.

Possible reasons for a non-startingengine:■ Clutch pedal not operated (manual

transmission)■ Brake pedal not operated or

selector lever not in P or N(automatic transmission)

■ Timeout occurred

Turbo engine warm-upUpon start-up, engine availabletorque may be limited for a short time,especially when the enginetemperature is cold. The limitation isto allow the lubrication system to fullyprotect the engine.

Overrun cut-offThe fuel supply is automatically cut offduring overrun, i.e. when the vehicleis driven with a gear engaged butaccelerator is released.

Driving and operating 121

Stop-start systemThe stop-start system helps to savefuel and to reduce the exhaustemissions. When conditions allow, itswitches off the engine as soon as thevehicle is at a low speed or ata standstill, e.g. at a traffic light or ina traffic jam. It starts the engineautomatically as soon as the clutch isdepressed. A battery sensor ensuresthat an Autostop is only performed ifthe battery is sufficiently charged fora restart.

ActivationThe stop-start system is available assoon as the engine is started, thevehicle starts-off and the conditionsas stated below in this section arefulfilled.

Deactivation

Deactivate the stop-start systemmanually by pressing the eco button.The deactivation is indicated whenthe LED in the button extinguishes.

AutostopIf the vehicle is at a low speed or ata standstill, activate an Autostop asfollows:■ Depress the clutch pedal■ set the lever in neutral■ release the clutch pedalThe engine will be switched off whilethe ignition stays on.

An Autostop is indicated by theneedle at the AUTOSTOP position inthe tachometer.During an Autostop, the heating andbrake performance will bemaintained.

Caution

The steering assist can bereduced during an Autostop.

122 Driving and operating

Conditions for an AutostopThe stop-start system checks if eachof the following conditions is fulfilled.Otherwise an Autostop will beinhibited.■ The stop-start system is not

manually deactivated■ the bonnet is fully closed■ the driver's door is closed or the

driver's seat belt is fastened■ the battery is sufficiently charged

and in good condition■ the engine is warmed up■ the engine coolant temperature is

not too high■ the engine exhaust temperature is

not too high, e.g. after driving withhigh engine load

■ the ambient temperature is not toolow

■ the climate control system does notinhibit an Autostop

■ the brake vacuum is sufficient

■ the self-cleaning function of thediesel particle filter is not active

■ the vehicle has moved since thelast Autostop

Ambient temperature near to thefreezing point can inhibit an Autostop.Certain settings of the climate controlsystem may inhibit an Autostop. SeeClimate control chapter for moredetails.Immediately after motorway drivingan Autostop may be inhibited.New vehicle running-in 3 119.

Battery discharge protectionTo ensure reliable engine restarts,several battery discharge protectionfeatures are implemented as part ofthe stop-start system.

Power saving measuresDuring an Autostop, several electricalfeatures such as auxiliary electricheater or rear window heating aredisabled or switched into a powersaving mode. The fan speed of theclimate control system is reduced tosave power.

Restart of the engine by thedriverDepress the clutch pedal to restart theengine.The engine start is indicated by theneedle at the idle speed position inthe tachometer.If the selector lever is shifted out ofneutral before depressing the clutchfirst, control indicator - illuminatesor is shown as a symbol in the DriverInformation Centre.Control indicator - 3 75.

Restart of the engine by thestop-start systemThe selector lever has to be in neutralto enable an automatic restart.If one of the following conditionsoccurs during an Autostop, theengine will be restarted automaticallyby the stop-start system.■ The stop-start system is manually

deactivated■ the bonnet is opened

Driving and operating 123

■ the driver's seat belt is unfastenedand the driver's door is opened

■ the engine temperature is too low■ the battery is discharged■ the brake vacuum is not sufficient■ the vehicle starts to move■ the climate control system requests

an engine start■ the air conditioning is manually

switched onIf the bonnet is not fully closed,a warning message is displayed in theDriver Information Centre.If an electrical accessory, e.g.a portable CD player, is connected tothe power outlet, a brief power dropduring restart might be noticeable.

Parking■ Do not park the vehicle on an easily

ignitable surface. The hightemperature of the exhaust systemcould ignite the surface.

■ Always apply parking brake. Applymanual parking brake withoutpressing release button. Apply as

firmly as possible on downhill oruphill slopes. Depress the footbrake at the same time to reduceoperating force.

■ Switch off the engine and ignition.Turn the steering wheel until thesteering wheel lock engages.

■ If the vehicle is on a level surface oruphill slope, engage first gear or setthe selector lever to P beforeswitching off the ignition. On anuphill slope, turn the front wheelsaway from the kerb.If the vehicle is on a downhill slope,engage reverse gear or set theselector lever to P before switchingoff the ignition. Turn the frontwheels towards the kerb.

■ Lock the vehicle and activate theanti-theft alarm system.

NoteIn the event of an accident withairbag deployment, the engine isturned off automatically if the vehiclecomes to a standstill within a certaintime.

Engine exhaust

9 Danger

Engine exhaust gases containpoisonous carbon monoxide,which is colourless and odourlessand could be fatal if inhaled.If exhaust gases enter the interiorof the vehicle, open the windows.Have the cause of the faultrectified by a workshop.Avoid driving with an open loadcompartment, otherwise exhaustgases could enter the vehicle.

Diesel particle filterThe diesel particle filter system filtersharmful soot particles out of theexhaust gases. The system includesa self-cleaning function that runsautomatically during driving withoutany notification. The filter is cleanedby periodically burning off the sootparticles at high temperature. Thisprocess takes place automaticallyunder set driving conditions and may

124 Driving and operating

take up to 25 minutes. Typically itneeds between 7 and 12 minutes.Autostop is not available and fuelconsumption may be higher duringthis period. The emission of smellsand smoke during this process isnormal.

Under certain driving conditions, e.g.short distances, the system cannotclean itself automatically.If the cleaning of the filter is requiredand if previous driving conditions didnot enable automatic cleaning, it willbe indicated by control indicator %.Simultaneously Diesel partic. filter is

full continue driving or warningcode 55 appears in the DriverInformation Centre.% illuminates when diesel particlefilter is full. Start cleaning process assoon as possible.% flashes when diesel particle filterhas reached the maximum fillinglevel. Start cleaning processimmediately to avoid damage to theengine.

Cleaning processTo activate cleaning process,continue driving, keep engine speedabove 2000 revolutions per minute.Shift down if necessary. Dieselparticle filter cleaning is then started.If g illuminates additionally,cleaning is not possible, seek theassistance of a workshop.

Caution

If the cleaning process isinterrupted, there is a risk ofprovoking severe engine damage.

Cleaning takes place quickest at highengine speeds and loads.The control indicator % extinguishesas soon as the self-cleaningoperation is complete.

Catalytic converterThe catalytic converter reduces theamount of harmful substances in theexhaust gases.

Caution

Fuel grades other than those listedon pages 3 146, 3 202 coulddamage the catalytic converter orelectronic components.Unburnt petrol will overheat anddamage the catalytic converter.Therefore avoid excessive use ofthe starter, running the fuel tankdry and starting the engine bypushing or towing.

In the event of misfiring, unevenengine running, a reduction in engineperformance or other unusualproblems, have the cause of the fault

Driving and operating 125

rectified by a workshop as soon aspossible. In an emergency, drivingcan be continued for a short period,keeping vehicle speed and enginespeed low.

Automatic transmissionThe automatic transmission permitsautomatic gearshifting (automaticmode) or manual gearshifting(manual mode).

Transmission display

The mode or selected gear is shownin the transmission display.

Selector lever

P = park position, wheels arelocked, engage only when thevehicle is stationary and theparking brake is applied

R = reverse gear, engage onlywhen the vehicle is stationary

N = neutralD = automatic mode with all gears

The selector lever is locked in P andcan only be moved when the ignitionis on and the brake pedal is applied.

126 Driving and operating

Without brake pedal applied, thecontrol indicator j illuminates.If the selector lever is not in P whenthe ignition is switched off, the controlindicators j and P flash.To engage P or R, press the releasebutton.The engine can only be started withthe lever in position P or N. Whenposition N is selected, press the brakepedal or apply the parking brakebefore starting.

Do not accelerate while engaginga gear. Never depress the acceleratorpedal and brake pedal at the sametime.When a gear is engaged, the vehicleslowly begins to creep when thebrake is released.

Engine brakingTo utilise the engine braking effect,select a lower gear in good time whendriving downhill, see manual mode.

Rocking the vehicleRocking the vehicle is onlypermissible if the vehicle is stuck insand, mud or snow. Move the selectorlever between D and R in a repeatpattern. Do not race the engine andavoid sudden acceleration.

ParkingApply the parking brake and engageP.The ignition key can only be removedwhen the selector lever is in positionP.

Manual mode

Move selector lever out of position Dtowards the left and then forwards orbackwards.< = Shift to a higher gear.

] = Shift to a lower gear.

If a higher gear is selected whenvehicle speed is too low, or a lowergear when vehicle speed is too high,the shift is not executed. This cancause a message in theDriver-Info-Display.

Driving and operating 127

In manual mode no automatic shiftingto a higher gear takes place at highengine revolutions.

Electronic drivingprogrammes■ Following a cold start, the operating

temperature programme increasesengine speed to quickly bring thecatalytic converter to the requiredtemperature.

■ The automatic neutral shift functionautomatically shifts to idling whenthe vehicle is stopped witha forward gear engaged and thebrake pedal is pressed.

■ When Sport mode is engaged, thevehicle shifts at higher enginespeeds (unless cruise control ison). Sport mode 3 133.

■ Special programmes automaticallyadapt the shifting points whendriving up inclines or down hills.

KickdownIf the accelerator pedal is presseddown completely in automatic mode,the transmission shifts to a lower geardepending on engine speed.

FaultIn the event of a fault, g illuminates.Additionally a code number ora vehicle message is displayed in theDriver Information Centre. Vehiclemessages 3 85.The transmission no longer shiftsautomatically. Continued travel ispossible with manual shifting.Only the highest gear is available.Depending on the fault, 2nd gear mayalso be available in manual mode.Shift only when vehicle is ata standstill.Have the cause of the fault remediedby a workshop.

Interruption of powersupplyIn the event of an interruption ofpower supply, the selector levercannot be moved out of the Pposition. The ignition key cannot beremoved from the ignition switch.If the battery is discharged, start thevehicle using jump leads 3 187.If the battery is not the cause of thefault, release the selector lever.1. Apply the parking brake.

128 Driving and operating

2. Release the selector lever trimfrom the centre console at thefront, fold it upwards and rotate itto the left.

3. Insert a screwdriver into theopening as far as it will go andmove the selector lever out of P orN. If P or N is engaged again, theselector lever will be locked inposition again. Have the cause ofthe power supply interruptionremedied by a workshop.

4. Mount the selector lever trim ontothe centre console and refit.

Manual transmission

To engage reverse, with the vehiclestationary wait 3 seconds afterdepressing the clutch pedal and thenpress the release button on theselector lever and engage the gear.If the gear does not engage, set thelever to neutral, release the clutchpedal and depress again; then repeatgear selection.Do not grind the clutch unnecessarily.When operating, depress the clutchpedal completely. Do not use thepedal as a foot rest.

Caution

It is not advisable to drive with thehand resting on the selector lever.

Driving and operating 129

BrakesThe brake system comprises twoindependent brake circuits.If a brake circuit fails, the vehicle canstill be braked using the other brakecircuit. However, braking effect isachieved only when the brake pedalis depressed firmly. Considerablymore force is needed for this. Thebraking distance is extended. Seekthe assistance of a workshop beforecontinuing your journey.When the engine is not running, thesupport of the brake servo unitdisappears once the brake pedal hasbeen depressed once or twice.Braking effect is not reduced, butbraking requires significantly greaterforce. It is especially important to bearthis in mind when being towed.Control indicator & 3 75.

Antilock brake systemAntilock brake system (ABS)prevents the wheels from locking.

ABS starts to regulate brake pressureas soon as a wheel shows a tendencyto lock. The vehicle remainssteerable, even during hard braking.ABS control is made apparentthrough a pulse in the brake pedaland the noise of the regulationprocess.For optimum braking, keep the brakepedal fully depressed throughout thebraking process, despite the fact thatthe pedal is pulsating. Do not reducethe pressure on the pedal.After starting off the system performsa self-test which may be audible.Control indicator u 3 76.

Adaptive brake lightDuring full braking, all three brakelights flash for the duration of ABScontrol.

Fault

9 Warning

If there is a fault in the ABS, thewheels may be liable to lock dueto braking that is heavier thannormal. The advantages of ABSare no longer available. Duringhard braking, the vehicle can nolonger be steered and mayswerve.

Have the cause of the fault remediedby a workshop.

130 Driving and operating

Parking brakeManual parking brake

Always apply parking brake firmlywithout operating the release button,and apply as firmly as possible ona downhill or uphill slope.To release the parking brake, pull thelever up slightly, press the releasebutton and fully lower the lever.To reduce the operating forces of theparking brake, depress the foot brakeat the same time.Control indicator & 3 75.

Electrical parking brake

Applying when vehicle is stationaryPull switch m, the electrical parkingbrake operates automatically with anadequate force. For maximum force,e.g. parking with trailer or on inclines,pull switch m twice.The electrical parking brake is appliedwhen control indicator m lights up3 76.The electrical parking brake canalways be activated, even if theignition is off.

Do not operate electrical parkingbrake system too often withoutengine running because this willdischarge the battery.Before leaving the vehicle, check theelectrical parking brake status.Control indicator m 3 76.

ReleasingSwitch on ignition. Keep brake pedaldepressed and then push switch m.

Drive away functionDepressing clutch pedal (manualtransmission) or engaging drive gear(automatic transmission) and thendepressing the accelerator pedalreleases the electrical parking brakeautomatically. This is not possiblewhen the switch is pulled at the sametime.This function also helps driving awayon inclines.Aggressive drive away may reducelife time of wear parts.

Driving and operating 131

Dynamic braking when vehicle ismovingWhen the vehicle is moving and theswitch m is kept pulled, the electricalparking brake system will deceleratethe vehicle, but will not applystatically.As soon as the switch m is released,dynamic braking will be stopped.

FaultFailure mode of electrical parkingbrake is indicated by control indicatorj and by a code number or a vehiclemessage which is displayed in theDriver Information Centre. Vehiclemessages 3 85.Apply electrical parking brake: pulland hold the switch m for more than5 seconds. If control indicator milluminates, electrical parking brake isapplied.Release electrical parking brake:push and hold the switch m for morethan 2 seconds. If control indicatorm extinguishes, electrical parkingbrake is released.

Control indicator m flashes: electricalparking brake is not fully applied orreleased. When continuouslyflashing, release electrical parkingbrake and retry applying.

Brake assistIf the brake pedal is depressedquickly and forcefully, maximumbrake force is automatically applied(full braking).Maintain steady pressure on thebrake pedal for as long as full brakingis required. Maximum brake force isautomatically reduced when thebrake pedal is released.

Hill start assistThe system helps prevent unintendedmovement when driving away oninclines.When releasing the foot brake afterstopping on an incline, the brakesremain on for a further two seconds.The brakes release automatically assoon as the vehicle begins toaccelerate.

The hill start assist is not active duringan Autostop.

132 Driving and operating

Ride control systemsTraction Control systemThe Traction Control system (TC) isa component of the ElectronicStability Control.TC improves driving stability whennecessary, regardless of the type ofroad surface or tyre grip, bypreventing the drive wheels fromspinning.As soon as the drive wheels starts tospin, engine output is reduced andthe wheel spinning the most is brakedindividually. This considerablyimproves the driving stability of thevehicle on slippery road surfaces.TC is operational as soon as thecontrol indicator b extinguishes.When TC is active b flashes.

9 Warning

Do not let this special safetyfeature tempt you into taking riskswhen driving.Adapt speed to the roadconditions.

Control indicator b 3 77.

Deactivation

TC can be switched off when spinningof drive wheels is required: pressbutton b briefly.Control indicator k illuminates.

TC is reactivated by pressing the bbutton again.TC is also reactivated the next timethe ignition is switched on.

Electronic Stability ControlElectronic Stability Control (ESC)improves driving stability whennecessary, regardless of the type ofroad surface or tyre grip. It alsoprevents the drive wheels fromspinning.As soon as the vehicle starts toswerve (understeer/oversteer),engine output is reduced and thewheels are braked individually. Thisconsiderably improves the drivingstability of the vehicle on slippery roadsurfaces.ESC is operational as soon as thecontrol indicator b extinguishes.When ESC is active b flashes.

Driving and operating 133

9 Warning

Do not let this special safetyfeature tempt you into taking riskswhen driving.Adapt speed to the roadconditions.

Control indicator b 3 77.

Deactivation

For very high-performance drivingESC can be deactivated: hold buttonb depressed for approx. 7 seconds.Control indicator n illuminates.

ESC is reactivated by pressing theb button again. If the TC system waspreviously disabled, both TC andESC are reactivated.ESC is also reactivated the next timethe ignition is switched on.

Interactive driving systemFlex RideFlex Ride driving system allows thedriver to select between three drivingmodes:■ SPORT mode: press button

SPORT, LED illuminates.■ TOUR mode: press button TOUR,

LED illuminates.■ Normal mode: both buttons

SPORT and TOUR are notpressed, no LED illuminates.

Deactivate SPORT mode and TOURmode by pressing correspondingbutton once more.

In each driving mode Flex Ridenetworks the following electronicsystems:■ Continuous Damping Control.■ Accelerator Pedal Control.■ Steering Control.■ Automatic transmission.

134 Driving and operating

SPORT modeThe settings of the systems areadapted to a sportier driving style:■ Damping of shock absorbers reacts

more stiffly to provide better contactwith the road surface.

■ The engine reacts more quickly tothe accelerator pedal.

■ Steering support is reduced.■ Shift points of automatic

transmission occur later.■ With SPORT mode activated, the

illumination of main instrumentschanges from white to red.

TOUR modeThe settings of the systems areadapted to a comfort driving style:■ Damping of shock absorbers reacts

more softly.■ Accelerator pedal reacts with

standard settings.■ Steering support is in standard

mode.

■ Shift points of automatictransmission occur in a comfortmode.

■ Illumination of main instruments iswhite.

Normal modeAll settings of the systems areadapted to standard values.

Drive mode controlWithin each manually selected drivingmode (SPORT, TOUR or Normal),the Drive Mode Control (DMC)detects and analyses continuouslythe real driving characteristic,responses by the driver, and theactive dynamic state of the vehicle. Ifnecessary, the control unit of DMCautomatically changes the settingswithin the selected driving mode or,when recognising greater variations,the driving mode is changed for thelength of variation.If, for example, Normal mode isselected and DMC detects a sportydriving behaviour, DMC changesseveral settings of the Normal mode

into sporty settings. The DMCchanges to Sport mode in case ofvery sporty driving behaviour.If, for example, TOUR mode isselected and whilst driving ona winding road a sudden hard brakeis necessary, DMC will detect thedynamic vehicle condition andchanges the settings for suspensionto SPORT mode, to increase vehiclestability.When the driving characteristic or thedynamic vehicle state returns to theformer state, DMC will change thesettings to the preselected drivingmode.

Personalised settings in theSport modeThe driver can select the functions ofthe SPORT mode when SPORTbutton is pressed. These settings canbe changed in the menu Settings inthe Info-Display. Vehiclepersonalisation 3 92.

Driving and operating 135

Driver assistancesystems

9 Warning

Driver assistance systems aredeveloped to support the driverand not to replace his attention.The driver accepts fullyresponsibility when driving thevehicle.When using driver assistancesystems, take always care on thetraffic situation.

Cruise controlThe cruise control can store andmaintain speeds of approx. 20 to120 mph. Deviations from the storedspeeds may occur when driving uphillor downhill.For safety reasons the cruise controlcannot be activated until the footbrake has been operated once.Activating in first gear is not possible.

Do not use the cruise control if it is notadvisable to maintain a constantspeed.With automatic transmission, onlyactivate cruise control in automaticmode.Control indicator m 3 79.

Switching onPress button m, control indicator m ininstrument cluster illuminates white.

ActivationAccelerate to the desired speed andturn thumb wheel to SET/-, thecurrent speed is stored and

maintained. Control indicator m ininstrument cluster illuminates green.Accelerator pedal can be released.Vehicle speed can be increased bydepressing the accelerator pedal.When the accelerator pedal isreleased, the previously stored speedis resumed.Cruise control remains activatedwhile gear is changed.

Increase speedWith cruise control active, hold thumbwheel turned to RES/+ or briefly turnto RES/+ repeatedly: speedincreases continuously or in smallincrements.Alternatively accelerate to the desiredspeed and store by turning to SET/-.

Reduce speedWith cruise control active, hold thumbwheel turned to SET/- or briefly turnto SET/- repeatedly: speeddecreases continuously or in smallincrements.

136 Driving and operating

DeactivationPress button y, control indicator m ininstrument cluster illuminates white.Cruise control is deactivated. Lastused set speed is stored in memoryfor later speed resume.Automatic deactivation:■ vehicle speed below approx.

20 mph,■ vehicle speed above approx.

125 mph,■ the brake pedal is depressed,■ the clutch pedal is depressed for

a few seconds,■ selector lever in N,■ engine speed in a very low range,■ the Traction Control system or

Electronic Stability Control isoperating.

Resume stored speedTurn thumb wheel to RES/+ ata speed above 20 mph. The storedspeed will be obtained.

Switching offPress button m, control indicator m ininstrument cluster extinguishes. Thestored speed is deleted.Pressing button L for activatingspeed limiter or switching off theignition also switches off cruisecontrol and deletes the stored speed.

Speed limiterThe speed limiter prevents thevehicle exceeding a preset maximumspeed.The maximum speed can be set ata speed above 15 mph.The driver can only accelerate up tothe preset speed. Deviations from thelimited speed may occur when drivingdownhill.The preset speed limit is displayed inthe top line of the Driver InformationCentre when the system is active.

Activation

Press button L. If cruise control oradaptive cruise control has beenactivated before, it is switched offwhen speed limiter is activated andthe control indicator m extinguishes.

Set speed limitWith speed limiter active, hold thumbwheel turned to RES/+ or briefly turnto RES/+ repeatedly until the desiredmaximum speed is displayed in theDriver Information Centre.Alternatively accelerate to the desiredspeed and briefly turn thumb wheel toSET/-: the current speed is stored as

Driving and operating 137

maximum speed. Speed limit isdisplayed in the Driver InformationCentre.

Change speed limitWith speed limiter active, turn thumbwheel to RES/+ to increase or SET/-to decrease the desired maximumspeed.

Exceeding the speed limitIn the event of an emergency it ispossible to exceed the speed limit bydepressing the accelerator pedalfirmly beyond the point of resistance.

The limited speed will flash in theDriver Information Centre anda chime sounds during this period.Release the accelerator pedal andthe speed limiter function isreactivated once a speed lower thanthe limit speed is obtained.

DeactivationPress button y: speed limiter isdeactivated and the vehicle can bedriven without speed limit.The limited speed is stored anda corresponding message appears inthe Driver Information Centre.

Resume limit speedTurn thumb wheel to RES/+. Thestored speed limit will be obtained.

Switching offPress button L, the speed limitindication in the Driver InformationCentre extinguishes. The storedspeed is deleted.

By pressing button m to activatecruise control or adaptive cruisecontrol or by switching off the ignition,speed limiter is also deactivated andthe stored speed is deleted.

Following distanceindicationThe following distance indicationdisplays the distance to a precedingmoving vehicle. The front camera inthe windscreen is used to detect thedistance of a vehicle directly ahead inthe vehicle's path. It is active atspeeds above 25 mph.When a preceding vehicle is detectedahead, the distance is indicated inseconds, displayed on a page in theDriver Information Centre 3 80. Pressthe MENU button on the turn signallever to select Vehicle InformationMenu X and turn the adjusterwheel to choose following distanceindication page.

138 Driving and operating

The minimum indicated distance is0.5 seconds.If there is no vehicle ahead or thevehicle ahead is out of range, twodashes will be displayed: -.- s.

Parking assist

The parking assist makes parkingeasier by measuring the distancebetween the vehicle and obstacles,and giving acoustic signals.The warning chime regardingunfastened seat belts has priorityover any other acoustic signal 3 88.Even when using the parking assist,the driver remains fully responsiblefor the parking manoeuvre.The system consists of four ultrasonicparking sensors in the rear bumper. Ifthe vehicle is equipped with a front

parking assist the system consists offour additional ultrasonic parkingsensors in the front bumper.The system uses two differentfrequencies for the front and rearsensors, respectively, each witha different sound.Control indicator r 3 77.

Activation

When reverse gear is engaged, thesystem is activated automatically.The front parking assist can also beactivated at a low speed by pressingthe r button.

Driving and operating 139

An illuminated LED in the parkingassist button indicates that thesystem is ready to operate.Depending on which of the sensorsare closer to an obstacle, you will hearthe buzzing sound of the respectivesensors. The interval between thesounds becomes shorter as thevehicle gets closer to the obstacle.When the distance is less than30 cm, the buzzing is continuous.If the r button is pressed oncewithin an ignition cycle, the frontparking assist is always reactivatedwhen the vehicle speed goes belowa certain value.

DeactivationDeactivate the system by pressingthe r button.The LED in the button will extinguishand Park Assist Off will be displayedin the Driver Information Centre.The system is deactivatedautomatically at a certain speed.

FaultIn the event of a fault in the system,r illuminates or a vehicle messageis displayed in the Driver InformationCentre.Additionally, r illuminates ora vehicle message is displayed in theDriver Information Centre ifa malfunction of the system due totemporary conditions like snowcovered sensors is detected.Vehicle messages 3 85.

Important hints for using theparking assist

9 Warning

Under certain circumstances,various reflective surfaces onobjects or clothing as well asexternal noise sources may causethe system to fail to detectobstacles.

Special attention has to be paid tolow obstacles which can damagethe lower part of the bumper. Ifsuch obstacles leave the detectionarea of the sensors duringapproach of the vehicle,a continuous warning tone willsound.

140 Driving and operating

Caution

Performance of the sensor can bereduced when sensors arecovered, e.g. by ice or snow.Performance of the parking assistsystems can be reduced due toheavy loading.Special conditions apply if thereare taller vehicles involved (e.g.off-road vehicles, mini vans,vans). Object identification in theupper part of these vehiclescannot be guaranteed.Objects with a very small reflectioncross section, like objects ofnarrow size or soft materials, maynot be detected by the system.Parking assist will not avoida collision with objects which areout of the detection range of thesensors.

NoteThe parking assist systemautomatically detects factory-fittedtowing equipment. It is deactivatedwhen the connector is plugged in.The sensor may detect a non-existing object (echo disturbance)caused by external acoustical ormechanic disturbances.

Traffic sign assistantFunctionalityThe traffic sign assistant systemdetects designated traffic signs viaa front camera and displays them inthe Driver Information Centre.

Traffic signs, which will be detected,are:Limit- and no passing signs■ speed limit■ no passing■ end of speed limit■ end of no passingRoad signs■ beginning of motorway■ end of motorway■ A-roads■ playstreetsAdd on signs■ additional hints to traffic signs■ wet warning■ ice warning■ direction arrowsSpeed limit signs are displayed in theDriver Information Centre until thenext speed limit sign or end of speedlimit is detected or rather sign timeoutand after a defined time.

Driving and operating 141

Combinations of more signs in thedisplay are possible.

An exclamation mark in a frameindicates that there is an add on signdetected which cannot be recognisedby the system.The system is active at an indicatedspeed above 9 mph and is active upto a speed of 124 mph depending onthe lighting conditions. At night thesystem is active up to a speed of99 mph.As soon as the speed becomesslower than 34 mph the display will bereset and the content of the traffic signpage will be cleared. The nextrecognized speed indication will bedisplayed.

Display indication

Traffic signs are displayed on thepage Traffic sign detection in the Trip/Fuel Information Menu, chosen viathe adjuster wheel on the turn signallever 3 80.When another function on the DriverInformation Centre menu wasselected and then Traffic signdetection page is chosen again, thelast recognised traffic sign will bedisplayed.

142 Driving and operating

If the system is deactivated, thecontent of the traffic sign page iscleared, indicated by the followingsymbol:

The content of the traffic sign page isalso cleared during driving by pushingthe SET/CLR button on the turn signallever for a longer time.

Pop-up functionSpeed limits and no passing signs aredisplayed as pop-ups on each pageof the menu.

The pop-up function can bedeactivated on the traffic sign page bypressing the SET/CLR button on theturn signal lever.

Once setting page is displayed, selectOff to deactivate pop-up function.Reactivated by selecting On. Whenswitching on the ignition, pop-upfunction is deactivated.Pop-up indication is displayed forapprox. 8 seconds in the DriverInformation Centre.

Driving and operating 143

Traffic sign detection inconjunction with navigationsystemIf the vehicle is equipped witha navigation system, the followingfeatures can be available:■ recognition of city limits■ constant indication of actual speed

limits■ immediate indication of speed limits

after leaving main route

FaultThe traffic sign assistant system maynot operate correctly when:■ the area of the windscreen, where

the front camera is located, is notclean

■ traffic signs are completely orpartially covered or difficult todiscern

■ there are adverse environmentalconditions like heavy rain, snow,direct sunlight or shadows. In thiscase No Traffic Sign Detection dueto Weather is indicated on thedisplay

■ traffic signs are incorrectly mountedor damaged

■ traffic signs do not comply with theVienna Convention on traffic signs(Wiener Übereinkommen überStraßenverkehrszeichen)

Caution

The system is intended to help thedriver within a defined speedrange to discern certain trafficsigns. Do not ignore traffic signswhich are not displayed by thesystem.The system does not discern anyother than the conventional trafficsigns that might give or enda speed limit.Do not let this special featuretempt you into taking risks whendriving.Always adapt speed to the roadconditions.

The driver assistance systems donot relieve the driver from fullresponsibility for vehicleoperation.

Lane departure warningThe lane departure warning systemobserves the lane markings betweenwhich the vehicle is driving via a frontcamera. The system detects lanechanges and warns the driver in theevent of an unintended lane changevia visual and acoustic signals.Criteria for the detection of anunintended lane change are:■ no operation of turn signals■ no brake pedal operation■ no active accelerator operation or

speeding-up■ no active steeringIf the driver is active, no warning willbe issued.

144 Driving and operating

Activation

The lane departure warning system isactivated by pressing the ) button.The illuminated LED in the buttonindicates that the system is switchedon. When the control indicator ) inthe instrument cluster illuminatesgreen, the system is ready to operate.The system is only operable atvehicle speeds above 37 mph and iflane markings are available.

When the system recognizes anunintended lane change, the controlindicator ) changes to yellow andflashes. Simultaneously a chimesound is activated.

DeactivationThe system is deactivated bypressing ) button. Deactivation isindicated by a message in the DriverInformation Centre.At speeds below 37 mph the systemis inoperable.

FaultThe lane departure warning systemmay not operate properly when:■ the windscreen is not clean■ there are adverse environmental

conditions like heavy rain, snow,direct sunlight or shadows

■ no lane marking can be detectedIf the lane departure warning systemdetects one of these conditions, thecontrol indicator ) illuminates yellow.Additionally a warning code ora warning message is displayed in theDriver Information Centre.

Tyre pressure monitoringsystemThe tyre pressure monitoring systemchecks the pressure of all four wheelsonce a minute when vehicle speedexceeds a certain limit.All wheels must be equipped withpressure sensors and the tyres musthave the prescribed pressure.

Driving and operating 145

The current tyre pressures can beshown in the Vehicle InformationMenu in the Driver InformationCentre.The menu can be selected by thebuttons on the turn signal lever.

Press the MENU button to select theVehicle Information Menu X.

Turn the adjuster wheel to select thetyre pressure monitoring system.System status and small pressuredifferences are displayed bya warning message with thecorresponding tyre flashing in theDriver Information Centre.Furthermore considerable pressuredifferences between the tyres on oneaxle are displayed by a warningmessage in the Driver InformationCentre.Major pressure differences areindicated additionally by the controlindicator w.

Control indicator w 3 78.Vehicle messages 3 85.If the tyre pressure shall be reducedor increased, switch off ignition.If a complete set of wheels withoutsensors is mounted (e.g. four wintertyres), a message is displayed in theDriver Information Centre. The tyrepressure monitoring system is notoperational. Retrofitting of sensors ispossible.A spare wheel or temporary sparewheel is not equipped with pressuresensors. The tyre pressuremonitoring system is not operationalfor these wheels. Control indicator willuminates. For the further threewheels the system remainsoperational.The use of commercially availableliquid tyre repair kits can impair thefunction of the system. Factoryapproved repair kits can be used.External high-power radio equipmentcould disrupt the tyre pressuremonitoring system.

146 Driving and operating

The tyre pressure monitoring systemvalve cores and sealing rings must bereplaced each time the tyres arechanged.

Adaptive threshold functionThe tyre pressure monitoring systemautomatically detects if the vehicle isdriven with a tyre pressureappropriate for a load of up to3 people or for a full load.If the tyre pressure shall be reduced,switch off ignition before reducing.

Auto learn functionAfter changing wheels the vehicle hasto be stationary for approx.20 minutes, before the systemrecalculates. The following relearnprocess takes up to 10 minutes ofdriving with a minimum speed of12 mph. In this case $ can bedisplayed or pressure values canswap in the Driver Information Centre.If problems occur during the relearnprocess a warning message isdisplayed in the Driver InformationCentre.

Temperature compensationCold tyres decrease the tyrepressure, warm tyres increase thetyre pressure. The tyre pressuremonitoring system considers thiseffect for the warning messages.The tyre pressure value displayed inthe Driver Information Centre showsthe actual tyre pressure. Therefore itis important to check tyre pressurewith cold tyres.

FuelFuel for petrol enginesOnly use unleaded fuel that complieswith EN 228.Usage of fuel with quality, notcomplying to the TechnicalRegulations in effect (Decree № 118of 27.02.2008 with amendments of30.12.2008 № 1076) can lead toengine damage and loss of allwarranty obligations.Equivalent standardised fuels with anethanol content of max. 10 % byvolume may be used. In this case onlyuse fuel that complies withE DIN 51626-1.Use fuel with the recommendedoctane rating 3 202. Use of fuel withtoo low an octane rating can reduceengine power and torque and slightlyincreases fuel consumption.

Driving and operating 147

Caution

Use of fuel that does not comply toEN 228 or similar can lead todeposits or engine damage andloss of warranty.

Caution

Use of fuel with too low an octanerating could lead to uncontrolledcombustion and engine damage.

Fuel for diesel enginesOnly use diesel fuel that complieswith EN 590.Usage of fuel with quality, notcomplying to the TechnicalRegulations in effect (Decree № 118of 27.02.2008 with amendments of30.12.2008 № 1076) can lead toengine damage and loss of allwarranty obligations.In countries outside the EuropeanUnion use Euro-Diesel fuel witha sulphur concentration below 50ppm.

Caution

Use of fuel that does not comply toEN 590 or similar can lead toengine powerloss, increased wearor engine damage and loss ofwarranty.

Do not use marine diesel oils, heatingoils, Aquazole and similar diesel-water emulsions. Diesel fuels mustnot be diluted with fuels for petrolengines.

Refuelling

9 Danger

Before refuelling, switch off engineand any external heaters withcombustion chambers. Switch offany mobile phones.Follow the operating and safetyinstructions of the filling stationwhen refuelling.

9 Danger

Fuel is flammable and explosive.No smoking. No naked flames orsparks.If you can smell fuel in yourvehicle, have the cause of thisremedied immediately by anauthorized dealer.

Caution

In case of misfuelling, do notswitch on ignition.

Fuel filler flap is located at right rearside of vehicle.

148 Driving and operating

The fuel filler flap can only be openedif the vehicle is unlocked. Release thefuel filler flap by pushing the flap.To open, turn the cap slowly to theleft.

The fuel filler cap can be retained inthe bracket on the fuel filler flap.For refuelling, fully insert the pumpnozzle and switch it on.After automatic cut-off, it can betopped up with max. two doses of fuel.

Caution

Wipe off any overflowing fuelimmediately.

To close, turn the fuel filler cap to theright until it clicks.Close the flap and let engage.

Fuel filler capOnly use genuine fuel filler caps.Diesel-engined vehicles have specialfuel filler caps.

Fuel consumption - CO2-EmissionsTo convert l/100 km into mpg, divide282 by number of litres/100 km.

PetrolThe fuel consumption is withina range of■ urban: 5.8 to 9.2 l/100 km,■ extra urban: 4.4 to 5.8 l/100 km,■ total: 4.9 to 7.1 l/100 km.The CO2 emission is within a range of■ 129 to 166 g/km.

General informationFor the values specific for yourvehicle, refer to the EEC Certificate ofConformity provided with your vehicleor other national registrationdocuments.

Driving and operating 149

The determination of fuelconsumption is regulated by directiveR (EC) No. 715/2007 (in the newestversion respectively).The specification of CO2 emission isalso a constituent of the directive.The figures given must not be takenas a guarantee for the actual fuelconsumption of a particular vehicle.Furthermore, fuel consumption isdependent on personal driving styleas well as road and traffic conditions.All values are based on the EU basemodel with standard equipment.The calculation of fuel consumptiontakes into account the vehicle's kerbweight, ascertained in accordancewith the regulations. Optionalequipment may result in slightlyhigher fuel consumption andCO2 emission levels and a lowermaximum speed.

TowingGeneral informationOnly use towing equipment that hasbeen approved for your vehicle.Entrust retrofitting of towingequipment to a workshop. It may benecessary to make changes thataffect the cooling system, heatshields or other equipment.The bulb outage detection function fortrailer brake light cannot detecta partial bulb outage, e.g. in case of4 x 5 Watts it only detects lampoutage when only a 5 watt lampremains or no lamp remains.Fitting of towing equipment couldcover the opening of the towing eye.If this is the case use the coupling ballbar for towing. Always keep thecoupling ball bar in the vehicle.Installation dimensions of factory-fitted towing equipment 3 208.

Driving characteristics andtowing tipsBefore attaching a trailer, lubricatethe coupling ball. However, do not doso if a stabiliser, which acts on thecoupling ball, is being used to reducesnaking movements.For trailers with low driving stabilityand caravan trailers with a permittedgross vehicle weight of more than1400 kg the use of a stabiliser isstrongly recommended when drivingabove 50 mph.If the trailer starts snaking, drive moreslowly, do not attempt to correct thesteering and brake sharply ifnecessary.When driving downhill, drive in thesame gear as if driving uphill anddrive at a similar speed.Adjust tyre pressure to the valuespecified for full load 3 206.

150 Driving and operating

Trailer towingTrailer loadsThe permissible trailer loads arevehicle and engine-dependentmaximum values which must not beexceeded. The actual trailer load isthe difference between the actualgross weight of the trailer and theactual coupling socket load with thetrailer coupled.The permissible trailer loads arespecified in the vehicle documents. Ingeneral, they are valid for gradientsup to max. 12 %.The permitted trailer load applies upto the specified incline and up to analtitude of 1000 metres above sealevel. Since engine power decreasesas altitude increases due to the airbecoming thinner, therefore reducingclimbing ability, the permissible grosstrain weight also decreases by 10 %for every 1000 metres of additionalaltitude. The gross train weight doesnot have to be reduced when drivingon roads with slight inclines (less than8 %, e.g. motorways).

The permissible gross train weightmust not be exceeded. This weight isspecified on the identification plate3 197.

Vertical coupling loadThe vertical coupling load is the loadexerted by the trailer on the couplingball. It can be varied by changing theweight distribution when loading thetrailer.The maximum permissible verticalcoupling load (75 kg) is specified onthe towing equipment identificationplate and in the vehicle documents.Always aim for the maximum load,especially in the case of heavytrailers. The vertical coupling loadshould never fall below 25 kg.

Rear axle loadWhen the trailer is coupled and thetowing vehicle fully loaded, thepermissible rear axle load (seeidentification plate or vehicledocuments) may be exceeded by70 kg, the gross vehicle weight ratingmay be exceeded by 70 kg. If thepermissible rear axle load isexceeded, a maximum speed of60 mph applies.

Towing equipment

Caution

When operating without a trailer,remove the coupling ball bar.

Driving and operating 151

Stowage of coupling ball bar

The bag with the coupling ball bar isstowed in the rear stowagecompartment on the floor.Place the strap through the lashingeye, wrap around twice and tightenthe strap to secure the bag.

Fitting the coupling ball bar

Disengage and fold down the socket.Remove the sealing plug from theopening for the coupling ball bar andstow it.

Checking the tensioning of thecoupling ball bar

■ Red marking on rotary knob mustpoint towards green marking oncoupling ball bar.

■ The gap between the rotary knoband the coupling ball bar must beapprox. 6 mm.

■ The key must be in position c.Otherwise, the coupling ball bar mustbe tensioned before being inserted:■ Unlock coupling ball bar by turning

key to position c.

152 Driving and operating

■ Pull out rotary knob and turnclockwise as far as it will go.

Inserting the coupling ball bar

Insert the tensioned coupling ball barin the opening and push firmlyupwards until it audibly engages.The rotary handle snaps back into itsoriginal position resting against thecoupling ball bar without a gap.

9 Warning

Do not touch rotary handle duringinsertion.

Lock the coupling ball bar by turningthe key to position e. Remove the keyand close the protective flap.

Eye for break-away stopping cable

Attach breakaway stopping cable toeye.

Check that the coupling ball bar iscorrectly installed■ Green marking on rotary knob must

point towards green marking oncoupling ball bar.

■ There must be no gap between therotary handle and the coupling ballbar.

Driving and operating 153

■ The coupling ball bar must be firmlyengaged in the opening.

■ The coupling ball bar must belocked and the key removed.

9 Warning

Towing a trailer is permitted onlywhen a coupling ball bar is fittedcorrectly. If the coupling ball bardoes not engage correctly, seekthe assistance of a workshop.

Dismounting the coupling ballbar

Open the protective flap and turn thekey to position c to unlock thecoupling ball bar.Pull out rotary handle and turnclockwise as far as it will go. Pull outcoupling ball bar downwards.Insert sealing plug in opening. Foldaway socket.

Trailer stability assistIf the system detects snakingmovements, engine power is reducedand the vehicle/trailer combination isselectively braked until the snakingceases. While system is working keepsteering wheel as still as possible.Trailer stability assist (TSA) isa function of the Electronic StabilityControl 3 132.

154 Vehicle care

Vehicle care

General Information ................... 154Vehicle checks ........................... 155Bulb replacement ....................... 162Electrical system ........................ 170Vehicle tools .............................. 176Wheels and tyres ....................... 176Jump starting ............................. 187Towing ....................................... 189Appearance care ....................... 191

General InformationAccessories and vehiclemodificationsWe recommend the use of genuineparts and accessories and factoryapproved parts specific for yourvehicle type. We cannot assess orguarantee reliability of other products- even if they have a regulatory orotherwise granted approval.Do not make any modifications to theelectrical system, e.g. changes ofelectronic control units (chip tuning).

Caution

When transporting the vehicle ona train or on a recovery vehicle, themud flaps might be damaged.

Vehicle storageStorage for a long period of timeIf the vehicle is to be stored for severalmonths:■ Wash and wax the vehicle.■ Have the wax in the engine

compartment and underbodychecked.

■ Clean and preserve the rubberseals.

■ Fill up fuel tank completely.■ Change the engine oil.■ Drain the washer fluid reservoir.■ Check the coolant antifreeze and

corrosion protection.■ Adjust tyre pressure to the value

specified for full load.■ Park the vehicle in a dry, well

ventilated place. Engage first orreverse gear or set selector lever toP. Prevent the vehicle from rolling.

■ Do not apply the parking brake.■ Open the bonnet, close all doors

and lock the vehicle.

Vehicle care 155

■ Disconnect the clamp from thenegative terminal of the vehiclebattery. Beware that all systems arenot functional, e.g. anti-theft alarmsystem.

Putting back into operationWhen the vehicle is to be put back intooperation:■ Connect the clamp to the negative

terminal of the vehicle battery.Activate the electronics of thepower windows.

■ Check tyre pressure.■ Fill up the washer fluid reservoir.■ Check the engine oil level.■ Check the coolant level.■ Fit the number plate if necessary.

End-of-life vehiclerecoveryInformation on end-of-life vehiclerecovery centres and the recycling ofend-of-life vehicles is available on ourwebsite. Only entrust this work to anauthorised recycling centre.

Vehicle checksPerforming work

9 Warning

Only perform engine compartmentchecks when the ignition is off.The cooling fan may startoperating even if the ignition is off.

9 Danger

The ignition system and Xenonheadlights use extremely highvoltage. Do not touch.

BonnetOpening

Pull the release lever and return it toits original position.

156 Vehicle care

Push the safety catch to the right andopen the bonnet.

Secure the bonnet support.

If the bonnet is opened during anAutostop, the engine will be restartedautomatically for safety reasons.

ClosingBefore closing the bonnet, press thesupport into the holder.Lower the bonnet and allow it to dropinto the catch. Check that the bonnetis engaged.

Engine oilCheck the engine oil level manuallyon a regular basis to prevent damageto the engine. Ensure that the correctspecification of oil is used.Recommended fluids and lubricants3 195.Check with the vehicle on a levelsurface. The engine must be atoperating temperature and switchedoff for at least 5 minutes.Pull out the dipstick, wipe it clean,insert it to the stop on the handle, pullout and read the engine oil level.

Caution

It is the owner's responsibility tomaintain the proper level of anappropriate quality oil in theengine.

Insert dipstick to the stop on thehandle and make half a turn.

Different dipsticks are useddepending on engine variant.

Vehicle care 157

When the engine oil level hasdropped to the MIN mark, top upengine oil.

We recommend the use of the samegrade of engine oil that was used atlast change.The engine oil level must not exceedthe MAX mark on the dipstick.

Caution

Overfilled engine oil must bedrained or suctioned out.

Capacities 3 205.Fit the cap on straight and tighten it.

Engine coolantThe coolant provides freezeprotection down to approx. -28 °C. Innorthern countries with very lowtemperatures the factory filled coolantprovides frost protection down toapprox. -37°C.

Caution

Only use approved antifreeze.

Coolant level

Caution

Too low a coolant level can causeengine damage.

If the cooling system is cold, thecoolant level should be above thefilling line mark. Top up if the level islow.

158 Vehicle care

9 Warning

Allow the engine to cool beforeopening the cap. Carefully openthe cap, relieving the pressureslowly.

To top up use a 1:1 mixture ofreleased coolant concentrate mixedwith clean tap water. If no coolantconcentrate is available, use cleantap water. Install the cap tightly. Havethe coolant concentration checkedand have the cause of the coolantloss remedied by a workshop.

Washer fluid

Fill with clean water mixed witha suitable quantity of windscreenwasher fluid which containsantifreeze. For the correct mixing ratiorefer to the washer fluid container.

Caution

Only washer fluid with a sufficientantifreeze concentration providesprotection at low temperatures ora sudden drop in temperature.

BrakesIn the event of minimum thickness ofthe brake lining, a squealing noisesounds during braking.Continued driving is possible buthave the brake lining replaced assoon as possible.Once new brake linings are installed,do not brake unnecessarily hard forthe first few journeys.

Brake fluid

9 Warning

Brake fluid is poisonous andcorrosive. Avoid contact with eyes,skin, fabrics and painted surfaces.

Vehicle care 159

The brake fluid level must be betweenthe MIN and MAX marks.When topping up, ensure maximumcleanliness as contamination of thebrake fluid can lead to brake systemmalfunctions. Have the cause of theloss of brake fluid remedied bya workshop.Only use high-performance brakefluid approved for the vehicle. Brakeand clutch fluid 3 195.

BatteryThe vehicle battery is maintenance-free provided that the driving profileallows sufficient charging of thebattery. Short-distance-driving andfrequent engine starts can dischargethe battery. Avoid the use ofunnecessary electrical consumers.

Batteries do not belong in householdwaste. They must be disposed of atan appropriate recycling collectionpoint.Laying up the vehicle for more than4 weeks can lead to batterydischarge. Disconnect the clamp fromthe negative terminal of the vehiclebattery.Ensure the ignition is switched offbefore connecting or disconnectingthe vehicle battery.

The anti-theft alarm siren must bedeactivated as follows: Switch theignition on then off, disconnect thevehicle's battery within 15 seconds.Battery discharge protection 3 108.

Replacing the batteryNoteAny deviation from the instructionsgiven in this paragraph may lead toa temporary deactivation of the stop-start system.

When the battery is being replaced,please ensure that there are no openventilation holes in the vicinity of thepositive terminal. If a ventilation holeis open in this area, it must be closedoff with a dummy cap, and theventilation in the vicinity of thenegative terminal must be opened.Only use batteries that allow the fusebox to be mounted above the battery.In vehicles with stop-start system,ensure to have the AGM (AbsorptiveGlass Mat) battery replaced with anAGM battery again.

160 Vehicle care

An AGM battery can be identified bythe label on the battery. Werecommend the use of an originalVauxhall battery.NoteUsing an AGM battery different fromthe original Vauxhall battery mightresult in a lower performance of thestop-start system.

We recommend that you have thebattery replaced by a workshop.Stop-start system 3 121.

Charging the battery

9 Warning

On vehicles with stop-startsystem, ensure that the chargingpotential does not exceed14.6 volts when using a batterycharger. Otherwise the batterymight be damaged.

Jump starting 3 187.

Warning label

Meaning of symbols:■ No sparks, naked flames or

smoking.■ Always shield eyes. Explosive

gases can cause blindness orinjury.

■ Keep the battery out of reach ofchildren.

■ The battery contains sulfuric acidwhich could cause blindness orserious burn injuries.

■ See the Owner’s Manual for furtherinformation.

■ Explosive gas may be present inthe vicinity of the battery.

Vehicle care 161

Diesel fuel systembleedingIf the tank has been run dry, the dieselfuel system must be bled. Switch onthe ignition three times for15 seconds at a time. Then start theengine for a maximum of40 seconds. Repeat this process afterno less than 5 seconds. If the enginefails to start, seek the assistance ofa workshop.

Wiper blade replacement

Lift the wiper arm until it stays in theraised position, press button todisengage the wiper blade andremove.Attach the wiper blade slightly angledto the wiper arm and push until itengages.Lower wiper arm carefully.

Wiper blade on the rear window

Lift wiper arm. Disengage wiper bladeas shown in illustration and remove.Attach the wiper blade slightly angledto the wiper arm and push until itengages.

Lower wiper arm carefully.

162 Vehicle care

Bulb replacementSwitch off the ignition and switch offthe relevant switch or close the doors.Only hold a new bulb at the base! Donot touch the bulb glass with barehands.Use only the same bulb type forreplacement.Replace headlight bulbs from withinthe engine compartment.

Bulb checkAfter a bulb replacement switch onthe ignition, operate and check thelights.

Halogen headlights

Bi-Halogen Headlight (1) with onebulb for low and high beam.Front turn signal (2).Sidelight/Daytime running light (3).

Low/High beam (1)

1. Rotate the cap (1) anticlockwiseand remove it.

Vehicle care 163

2. Rotate the bulb holderanticlockwise to disengage.Withdraw the bulb holder from thereflector.

3. Disengage the bulb holder fromthe plug connector by pressingthe retaining lug.

4. Replace the bulb and connectbulb holder with the plugconnector.

5. Insert the bulb holder, engagingthe two lugs into the reflector androtate clockwise to secure.

6. Fit the cap and rotate clockwise.

Front turn signal (2)

1. Rotate cap (2) anticlockwise andremove it.

2. Rotate bulb holder anticlockwiseand remove.

3. Remove the bulb from the socketby turning anticlockwise.

4. Replace and insert new bulb intosocket by turning clockwise.

5. Insert the bulb holder into thereflector and turn clockwise.

6. Fit the cap and rotate clockwise.

164 Vehicle care

Sidelight/Daytime running light(3)

1. Rotate bulb socket (3)anticlockwise to disengage.Withdraw the bulb socket from thereflector.

2. Remove the bulb from the socketby pulling.

3. Replace and insert new bulb intosocket.

4. Insert the bulb socket into thereflector and turn clockwise.

Adaptive forward lighting

9 Danger

Adaptive forward lighting systemuses Xenon headlights.Xenon headlights work underextremely high electrical voltage.Do not touch. Have bulbs replacedby a workshop.Bulbs for front turn signal andcorner lighting can be changed.

Sidelight/Daytime running lights aredesigned as Light Emitting Diodes(LEDs) and cannot be changed.

Vehicle care 165

Cornering light

1. Rotate the cap anticlockwise andremove it.

2. Rotate the bulb holderanticlockwise to disengage.Withdraw the bulb holder from thereflector.

3. Disengage the bulb from the plugconnector by pulling.

4. Replace the bulb and connectbulb holder with the plugconnector.

5. Insert the bulb holder, engagingthe two lugs into the reflector androtate clockwise to secure.

6. Fit the cap and rotate clockwise.

Front turn signal

1. Rotate the cap anticlockwise andremove it.

166 Vehicle care

2. Rotate bulb socket anticlockwiseto disengage. Withdraw the bulbsocket from the reflector.

3. Remove the bulb from the socketby turning anticlockwise.

4. Replace and insert new bulb intosocket by turning clockwise.

5. Insert the bulb socket into thereflector and turn clockwise.

6. Fit the cap and rotate clockwise.

Fog lights

1. Disengage the cover witha screwdriver in the recess andremove the cover.

2. Unscrew both screws and removelight assembly.

Vehicle care 167

3. Turn the bulb holder anti-clockwise and remove it from thereflector.

4. Disengage the bulb socket fromthe plug connector by pressingthe retaining lug.

5. Remove and replace the bulbsocket with bulb and attach theplug connector.

6. Insert the bulb socket into thereflector by turning clockwise andengage.

7. Mount the light assembly bytightening both screws.

8. Assemble and engage the cover.

Tail lights

1. Release the cover and remove it.

2. Unscrew both plastic securingnuts from the inside by hand.

3. Carefully withdraw the lightassembly from retaining pins andremove.

4. Detach the plug connector fromthe light assembly.

168 Vehicle care

5. Remove and replace the bulb byturning the bulb socket anti-clockwise.Tail light/Brake light (1)Turn signal light (2)Tail lights with Light EmittingDiode (LED) for tail and brake lightOnly turn signal light (2) can bechanged.

6. Insert and turn bulb holderclockwise into the tail lightassembly.

7. Connect the plug connector withthe light assembly.

8. Fit light assembly onto retainingpins and tighten the securing nuts.

9. Close the cover and engage.

Lights in the tailgate

1. Open the tailgate and remove thecovers.

2. Unscrew three screws.3. Remove the tail light assembly.

4. Turn bulb holder anti-clockwiseand remove it from the reflector.Replace the bulb:Tail light (1)Rear fog light (2) (only one side)Reverse light (2) (only one side)Tail lights with Light EmittingDiode (LED)Only rear fog light rsp. reverselight (2) can be changed.

5. Replace and insert new bulb intosocket.

6. Insert the bulb socket into thereflector and turn clockwise.

Vehicle care 169

7. Install the tail light assembly in thetailgate and tighten the screws.

8. Attach all covers.

Side turn signal lightsHave bulbs replaced by a workshop.

Number plate light

1. Insert screwdriver in recess of thecover, press to the side andrelease spring. Remove cover.

2. Remove the bulb holderdownwards, taking care not to pullon the cable.

3. Disengage the retaining lug andremove the bulb holder from thewiring plug.

4. Remove and replace the bulbholder with bulb.

5. Connect the wiring plug to thebulb holder.

6. Push the bulb holder into thehousing and close the cover.

Interior lightsCourtesy light, reading lightsHave bulbs replaced by a workshop.

Load compartment lightHave bulbs replaced by a workshop.

Instrument panelilluminationHave bulbs replaced by a workshop.

170 Vehicle care

Electrical systemFusesData on the replacement fuse mustmatch the data on the defective fuse.There are three fuse boxes in thevehicle:■ in the front left of the engine

compartment,■ in left-hand drive vehicles, in the

interior behind the storagecompartment, or, in right-handdrive vehicles, behind theglovebox,

■ behind a cover on the left side of theload compartment.

Before replacing a fuse, turn off therespective switch and the ignition.A blown fuse can be recognized by itsmelted wire. Do not replace the fuseuntil the cause of the fault has beenremedied.Some functions are protected byseveral fuses.Fuses may also be inserted withoutexistence of a function.

Fuse extractorA fuse extractor may be located in thefuse box in the engine compartment.

Vehicle care 171

Place the fuse extractor on thevarious types of fuse from the top orside, and withdraw fuse.

Engine compartment fusebox

The fuse box is in the front left of theengine compartment.Disengage the cover, lift it upwardsand remove.

172 Vehicle care

No. Circuit

1 Engine control module

2 Lambda probe

3 Fuel injection, ignition system

4 Fuel injection, ignition system

5 –

6 Mirror heating

7 Fan control

8 Lambda probe, engine

9 Rear window sensor

10 Battery sensor

11 Trunk release

12 Adaptive forward lightingmodule

13 –

14 Rear window wiper

15 Engine control module

16 Starter

No. Circuit

17 Transmission control module

18 Heated rear window

19 Front power windows

20 Rear power windows

21 ABS

22 Left high beam (Halogen)

23 Headlamp washer system

24 Right low beam (Xenon)

25 Left low beam (Xenon)

26 Fog lights

27 Diesel fuel heating

28 –

29 Electrical parking brake

30 ABS

31 –

32 Airbag

33 Adaptive forward lighting

No. Circuit

34 –

35 Power windows

36 –

37 Canister vent solenoid

38 Vacuum pump

39 Fuel system control module

40 Windscreen washer, Rearwindow washer system

41 Right high beam (Halogen)

42 Radiator fan

43 Windscreen wiper

44 –

45 Radiator fan

46 –

47 Horn

48 Radiator fan

49 Fuel pump

Vehicle care 173

No. Circuit

50 Headlamp levelling

51 Air shutter

52 Auxiliary heater, diesel engine

53 Transmission control module,Engine control module

54 Wiring monitoring

After having changed defective fusesclose the fuse box cover and pressuntil it engages.If the fuse box cover is not closedcorrectly, malfunction may occur.

Instrument panel fuse box

In left-hand drive vehicles, the fusebox is behind the storagecompartment in the instrument panel.Open the compartment and push it tothe left to unlock. Fold thecompartment down and remove it.

In right-hand drive vehicles, the fusebox is located behind a cover in theglovebox. Open the glovebox, thenopen the cover and fold it down.

174 Vehicle care

No. Circuit

1 Displays

2 Exterior lights

3 Exterior lights

4 Radio

5 Infotainment system,instrument

6 Power outlet front

7 Power outlet rear seat

8 Left low beam

9 Right low beam

10 Door locks

11 Interior fan

12 –

13 –

14 Diagnostic connector

15 Airbag

16 –

No. Circuit

17 Air conditioning system

18 Prefuse: radio, Infotainment,displays

19 Brake lights, tail lights, interiorlights

20 –

21 –

22 Ignition switch

23 Body control unit

24 Body control unit

25 –

26 Power outlet load compartment

Load compartment fuseboxThe fuse box is on the left side of theload compartment behind a cover.

Remove the cover.

Vehicle care 175

Fuse assignments No. Circuit

1 Trailer module

2 Trailer outlet

3 Parking assist

4 –

5 –

6 –

7 –

8 Anti-theft alarm system

9 –

10 –

11 Trailer module, Trailer socket

12 –

13 Trailer outlet

14 –

15 –

16 –

17 –

No. Circuit

18 –

19 Steering wheel heating

20 –

21 Seat heating

22 –

23 –

24 –

25 –

26 –

27 –

28 –

29 –

30 –

31 Amplifier, Subwoofer

32 Active damping system, Lanedeparture warning

176 Vehicle care

When assembling press the blind intothe rubber grommets to reach fullretention force.

Vehicle toolsToolsVehicles with tyre repair kit

The tools and tyre repair kit are ina storage compartment below thefloor cover in the load compartment.

Vehicles with spare wheelThe jack, the tools and a strap forsecuring a damaged wheel are ina storage compartment below thespare wheel in the load compartment.Spare wheel 3 184.

Wheels and tyres

Tyre condition, wheel conditionDrive over edges slowly and at rightangles if possible. Driving over sharpedges can cause tyre and wheeldamage. Do not trap tyres on the kerbwhen parking.Regularly check the wheels fordamage. Seek the assistance ofa workshop in the event of damage orunusual wear.

Winter tyresWinter tyres improve driving safety attemperatures below 7 °C and shouldtherefore be fitted on all wheels.In accordance with country-specificregulations, affix the speed sticker inthe driver's field of view.

Vehicle care 177

Tyre designationsE.g. 215/60 R 16 95 H215 = Tyre width, mm60 = Cross-section ratio (tyre

height to tyre width), %R = Belt type: RadialRF = Type: RunFlat16 = Wheel diameter, inches95 = Load index e.g. 95 is

equivalent to 690 kgH = Speed code letter

Speed code letter:Q = up to 100 mphS = up to 112 mphT = up to 118 mphH = up to 130 mphV = up to 150 mphW = up to 168 mph

Tyre pressureCheck the pressure of cold tyres atleast every 14 days and before anylong journey. Do not forget the sparewheel. This also applies to vehicleswith tyre pressure monitoring system.Unscrew the valve cap.

Tyre pressure 3 206 and on the labelon the front left door frame.The tyre pressure data refers to coldtyres. It applies to summer and wintertyres.Always inflate the spare tyre to thepressure specified for full load.The ECO tyre pressure serves toachieve the smallest amount of fuelconsumption possible.Incorrect tyre pressures will impairsafety, vehicle handling, comfort andfuel economy and will increase tyrewear.

9 Warning

If the pressure is too low, this canresult in considerable tyre warm-up and internal damage, leading totread separation and even to tyreblow-out at high speeds.

If the tyre pressure shall be reducedor increased on a vehicle with tyrepressure monitoring system, switchoff ignition.

Tread depthCheck tread depth at regularintervals.Tyres should be replaced for safetyreasons at a tread depth of 2-3 mm(4 mm for winter tyres).

178 Vehicle care

The legally permissible minimumtread depth (1.6 mm) has beenreached when the tread has worndown as far as one of the tread wearindicators (TWI). Their position isindicated by markings on thesidewall.If there is more wear at the front thanthe rear, swap round front wheels andrear wheels periodically. Ensure thatthe direction of rotation of the wheelsis the same as before.Tyres age, even if they are not used.We recommend tyre replacementevery 6 years.

Changing tyre and wheelsizeIf tyres of a different size than thosefitted at the factory are used, it may benecessary to reprogramme thespeedometer as well as the nominaltyre pressure and make other vehiclemodifications.After converting to a different tyresize, have the label with tyrepressures replaced.

9 Warning

Use of unsuitable tyres or wheelsmay lead to accidents and willinvalidate the vehicle typeapproval.

Wheel coversWheel covers and tyres that arefactory approved for the respectivevehicle and comply with all of therelevant wheel and tyre combinationrequirements must be used.

If the wheel covers and tyres used arenot factory approved, the tyres mustnot have a rim protection ridge.Wheel covers must not impair brakecooling.

9 Warning

Use of unsuitable tyres or wheelcovers could lead to suddenpressure loss and therebyaccidents.

Tyre chains

Use tyre chains only on front wheels.

Vehicle care 179

Tyre chains are permitted on tyres ofsize 225/55 R 17. Always use finemesh chains that add no more than10 mm to the tyre tread and theinboard sides (including chain lock).

9 Warning

Damage may lead to tyre blowout.

On tyres of size 245/45 R 18, specialsnow chains are only permitted whenthey are designed with a rotatingchain belt on the tyre tread, no chainlinks on the wheel inboard sides andthe chains add no more than 12 mmto the tyre tread. For furtherinformation of right snow chain usagefor this tyre size, contact a specializedvehicle parts dealer or snow chainmanufacturer.Tyre chains are not permitted on tyresof size 235/55 R 17, 235/50 R 18,235/45 R 19, 245/40 R 20.The use of tyre chains is not permittedon the temporary spare wheel.

Tyre repair kitMinor damage to the tyre tread can berepaired with the tyre repair kit.Do not remove foreign bodies fromthe tyres.Tyre damage exceeding 4 mm or thatis at tyre's sidewall cannot be repairedwith the tyre repair kit.

9 Warning

Do not drive faster than 50 mph.Do not use for a lengthy period.Steering and handling may beaffected.

If you have a flat tyre:Apply the parking brake and engagefirst gear, reverse gear or P.

The tyre repair kit is in a compartmentunder the floor cover in the loadcompartment.1. Take the tyre repair kit from the

compartment.2. Remove the compressor.

180 Vehicle care

3. Remove the electrical connectioncable and air hose from thestowage compartments on theunderside of the compressor.

4. Screw the compressor air hose tothe connection on the sealantbottle.

5. Fit the sealant bottle into theretainer on the compressor.Set the compressor near the tyrein such a way that the sealantbottle is upright.

6. Unscrew valve cap from defectivetyre.

7. Screw the filler hose to the tyrevalve.

8. The switch on the compressormust be set to J.

9. Connect the compressor plug tothe power outlet or cigarettelighter socket.To avoid discharging the battery,we recommend running theengine.

10. Set the rocker switch on thecompressor to I. The tyre is filledwith sealant.

11. The compressor pressure gaugebriefly indicates up to 6 bar whilstthe sealant bottle is emptying(approx. 30 seconds). Then thepressure starts to drop.

Vehicle care 181

12. All of the sealant is pumped intothe tyre. Then the tyre is inflated.

13. The prescribed tyre pressureshould be obtained within10 minutes. Tyre pressure3 206. When the correct pressureis obtained, switch off thecompressor.

If the prescribed tyre pressure isnot obtained within 10 minutes,remove the tyre repair kit. Movethe vehicle one tyre rotation.Reattach the tyre repair kit andcontinue the filling procedure for10 minutes. If the prescribed tyrepressure is still not obtained, the

tyre is too badly damaged. Seekthe assistance of a workshop.Drain excess tyre pressure withthe button over the pressureindicator.Do not run the compressor longerthan 10 minutes.

14. Detach the tyre repair kit. Pushcatch on bracket to removesealant bottle from bracket. Screwthe tyre inflation hose to the freeconnection of the sealant bottle.This prevents sealant fromescaping. Stow tyre repair kit inload compartment.

15. Remove any excess sealantusing a cloth.

16. Take the label indicatingmaximum permitted speed fromthe sealant bottle and affix in thedriver's field of view.

17. Continue driving immediately sothat sealant is evenly distributedin the tyre. After driving approx.6 miles (but no more than10 minutes), stop and check tyrepressure. Screw compressor air

hose directly onto tyre valve andcompressor when doing this.

If tyre pressure is more than1.3 bar, set it to the correct value.Repeat the procedure until thereis no more loss of pressure.If the tyre pressure has fallenbelow 1.3 bar, the vehicle mustnot be used. Seek the assistanceof a workshop.

18. Stow away tyre repair kit in loadcompartment.

182 Vehicle care

NoteThe driving characteristics of therepaired tyre are severely affected,therefore have this tyre replaced.If unusual noise is heard or thecompressor becomes hot, turncompressor off for at least30 minutes.The built-in safety valve opens ata pressure of 102 psi.Note the expiry date of the kit. Afterthis date its sealing capability is nolonger guaranteed. Pay attention tostorage information on sealantbottle.Replace the used sealant bottle.Dispose of the bottle as prescribedby applicable laws.The compressor and sealant can beused from approx. -30 °C.The adapters supplied can be usedto pump up other items e.g.footballs, air mattresses, inflatabledinghies etc. They are located on theunderside of the compressor. Toremove, screw on compressor airhose and withdraw adapter.

Wheel changingSome vehicles are equipped witha tyre repair kit instead of a sparewheel 3 179.Make the following preparations andobserve the following information:■ Park the vehicle on a level, firm and

non-skid surface. The front wheelsmust be in the straight-aheadposition.

■ Apply the parking brake andengage first gear, reverse gear orP.

■ Remove the spare wheel 3 184.■ Never change more than one wheel

at once.■ Use the jack only to change wheels

in case of puncture, not forseasonal winter or summer tyrechange.

■ If the ground on which the vehicleis standing is soft, a solid board(max. 1 cm thick) should be placedunder the jack.

■ No people or animals may be in thevehicle when it is jacked-up.

■ Never crawl under a jacked-upvehicle.

■ Do not start the vehicle when it israised on the jack.

■ Clean wheel nuts and thread witha clean cloth before mounting thewheel.

9 Warning

Do not grease wheel bolt, wheelnut and wheel nut cone.

1. Disengage wheel nut caps witha screwdriver and remove. Pull off

Vehicle care 183

the wheel cover with the hook.Vehicle tools 3 176.Alloy wheels: Disengage wheelnut caps with a screwdriver andremove. To protect the wheel,place a soft cloth between thescrewdriver and the alloy wheel.

Alloy wheels with centre wheelbolt cap: Disengage centre cap byinserting and pulling the extractor3 176 in the recess of the brandemblem.

2. Install the wheel wrench ensuringthat it locates securely and looseneach wheel nut by half a turn.

3. Ensure the jack is correctlypositioned under the relevantvehicle jacking point.

4. Set the jack to the necessaryheight. Position it directly belowthe jacking point in a manner thatprevents it from slipping.

184 Vehicle care

Attach jack handle and with thejack correctly aligned rotatehandle until wheel is clear of theground.

5. Unscrew the wheel nuts.6. Change the wheel. Spare wheel

3 184.7. Screw on the wheel nuts.8. Lower vehicle.9. Install the wheel wrench ensuring

that it locates securely and tighteneach nut in a crosswisesequence. Tightening torque is140 Nm.

10. Align the valve hole in the wheelcover with the tyre valve beforeinstalling.Install wheel nut caps.Install centre cap on alloy wheels.

11. Stow the replaced wheel 3 184and the vehicle tools 3 176.

12. Check the tyre pressure of theinstalled tyre and the wheel nuttorque as soon as possible.

Have the defective tyre renewed orrepaired as soon as possible.

Jacking position for liftingplatform

Rear arm position of the liftingplatform centrically under the recessof the sill.

Front arm position of the liftingplatform at the underbody.

Spare wheelSome vehicles are equipped witha tyre repair kit instead of a sparewheel.The spare wheel can be classified asa temporary spare wheel dependingon the size compared to the othermounted wheels and countryregulations.

Vehicle care 185

The spare wheel has a steel rim.

Caution

The use of a spare wheel that issmaller than the other wheels or incombination with winter tyrescould affect driveability. Have thedefective tyre replaced as soon aspossible.

The spare wheel is located in thespare wheel well beneath the floorcovering.To remove:1. Open the floor cover.

2. Remove rear storage: press bothbuttons and fold down cover.Extract storage upwards.

3. The spare wheel is secured witha wing nut. Untwist nut, removeconus and take out the sparewheel.Under the spare wheel there is thebox with vehicle tools.

4. Change the damaged wheel3 182.

5. Secure the tool box by turningright back the conus and the wingnut, close floor cover and insertrear storage.

The spare wheel well is not designedfor other tyre sizes than spare wheel.

Stowing a damaged wheel in theload compartmentA damaged wheel must be stowed inthe load compartment and securedwith a strap. Vehicle tools 3 176.1. Position the wheel close to one

sidewall of the load compartment.

2. Place the loop end of the strapthrough the front lashing eye onthe appropriate side.

186 Vehicle care

3. Place the hook end of the strapthrough the loop and pull it untilthe strap is fastened securely tothe lashing eye.

4. Insert the strap through thespokes of the wheel as shown inthe illustration.

5. Mount the hook to the rear lashingeye.

6. Tighten the strap and secure itusing the buckle.

Stowing the spare wheel back inthe well after replacing thedamaged wheel1. Open floor cover, remove rear

storage, untwist and remove wingnut and conus.

2. Place spare wheel with outsideupwards in the wheel well.

3. Position the excentric conus in therecess of the spare wheel andsecure by turning the wing nutright back.

4. Close floor cover and insert rearstorage.

9 Warning

Storing a jack, a wheel or otherequipment in the loadcompartment could cause injury ifthey are not fixed properly. Duringa sudden stop or a collision, looseequipment could strike someone.Store jack and tools always in therespective storage compartmentsand secure them by fixing.Damaged wheel placed in the loadcompartment must always besecured by the strap.

Temporary spare wheel

Caution

The use of a spare wheel that issmaller than the other wheels or incombination with winter tyrescould affect driveability. Have thedefective tyre replaced as soon aspossible.

Vehicle care 187

Only mount one temporary sparewheel. Do not drive faster than50 mph. Take curves slowly. Do notuse for a long period of time.If your vehicle gets a flat tyre on therear while towing another vehicle,mount the temporary spare wheel inthe front and the full tyre in the rear.Tyre chains 3 178.

Directional tyresFit directional tyres such that they rollin the direction of travel. The rollingdirection is indicated by a symbol(e.g. an arrow) on the sidewall.The following applies to tyres fittedopposing the rolling direction:■ Driveability may be affected. Have

the defective tyre renewed orrepaired as soon as possible.

■ Drive particularly carefully on wetand snow-covered road surfaces.

Jump startingDo not start with quick charger.A vehicle with a discharged batterycan be started using jump leads andthe battery of another vehicle.

9 Warning

Be extremely careful when startingwith jump leads. Any deviationfrom the following instructions canlead to injuries or damage causedby battery explosion or damage tothe electrical systems of bothvehicles.

9 Warning

Avoid contact of the battery witheyes, skin, fabrics and paintedsurfaces. The fluid containssulphuric acid which can causeinjuries and damage in the eventof direct contact.

■ Never expose the battery to nakedflames or sparks.

■ A discharged battery can alreadyfreeze at a temperature of 0 °C.Defrost the frozen battery beforeconnecting jump leads.

■ Wear eye protection and protectiveclothing when handling a battery.

■ Use a booster battery with thesame voltage (12 Volts). Itscapacity (Ah) must not be muchless than that of the dischargedbattery.

■ Use jump leads with insulatedterminals and a cross section of atleast 16 mm2 (25 mm2 for dieselengines).

■ Do not disconnect the dischargedbattery from the vehicle.

■ Switch off all unnecessary electricalconsumers.

■ Do not lean over the battery duringjump starting.

■ Do not allow the terminals of onelead to touch those of the otherlead.

188 Vehicle care

■ The vehicles must not come intocontact with each other during thejump starting process.

■ Apply the parking brake,transmission in neutral, automatictransmission in P.

Lead connection order:1. Connect the red lead to the

positive terminal of the boosterbattery.

2. Connect the other end of the redlead to the positive terminal of thedischarged battery.

3. Connect the black lead to thenegative terminal of the boosterbattery.

4. Connect the other end of the blacklead to a vehicle grounding point,such as the engine block or anengine mounting bolt. Connect asfar away from the dischargedbattery as possible, however atleast 60 cm.

Route the leads so that they cannotcatch on rotating parts in the enginecompartment.To start the engine:1. Start the engine of the vehicle

providing the jump.2. After 5 minutes, start the other

engine. Start attempts should bemade for no longer than15 seconds at an interval of1 minute.

3. Allow both engines to idle forapprox. 3 minutes with the leadsconnected.

4. Switch on electrical consumers(e.g. headlights, heated rearwindow) of the vehicle receivingthe jump start.

5. Reverse above sequence exactlywhen removing leads.

Vehicle care 189

TowingTowing the vehicle

Insert a screwdriver in the slot at thelower bend of the cap. Release thecap by carefully moving thescrewdriver downwards.The towing eye is stowed with thevehicle tools 3 176.

Screw in the towing eye as far as it willgo until it stops in a horizontalposition.Attach a tow rope – or better still a towrod – to the towing eye.The towing eye must only be used fortowing and not for recovering thevehicle.Switch on ignition to release steeringwheel lock and to permit operation ofbrake lights, horn and windscreenwiper.Transmission in neutral.Switch on the hazard warningflashers on both vehicles.

Caution

Drive slowly. Do not drive jerkily.Excessive tractive force candamage the vehicle.

When the engine is not running,considerably more force is needed tobrake and steer.To prevent the entry of exhaust gasesfrom the towing vehicle, switch on theair recirculation and close thewindows.Vehicles with automatic transmission:The vehicle must be towed facingforwards, not faster than 50 mph norfurther than 60 miles. In all othercases and when the transmission isdefective, the front axle must beraised off the ground.Seek the assistance of a workshop.After towing, unscrew the towing eye.Insert cap at the top and engagedownwards.

190 Vehicle care

Towing another vehicle

Insert a screwdriver in the slot at thelower bend of the cap. Release thecap by carefully moving thescrewdriver downwards.The towing eye is stowed with thevehicle tools 3 176.

Screw in the towing eye as far as it willgo until it stops in a horizontalposition.The lashing eye at the rearunderneath the vehicle must never beused as a towing eye.Attach a tow rope – or even bettera tow bar – to the towing eye.The towing eye must only be used fortowing and not for recoveringa vehicle.

Caution

Drive slowly. Do not drive jerkily.Excessive tractive force candamage the vehicle.

After towing, unscrew the towing eye.Insert cap at the top and engagedownwards.

Vehicle care 191

Appearance careExterior careLocksThe locks are lubricated at the factoryusing a high quality lock cylindergrease. Use de-icing agent only whenabsolutely necessary, as this hasa degreasing effect and impairs lockfunction. After using de-icing agent,have the locks regreased bya workshop.

WashingThe paintwork of your vehicle isexposed to environmental influences.Wash and wax your vehicle regularly.When using automatic vehiclewashes, select a programme thatincludes waxing.Bird droppings, dead insects, resin,pollen and the like should be cleanedoff immediately, as they containaggressive constituents which cancause paint damage.

If using a vehicle wash, comply withthe vehicle wash manufacturer'sinstructions. The windscreen wiperand rear window wiper must beswitched off. Remove antenna andexternal accessories such as roofracks etc.If you wash your vehicle by hand,make sure that the insides of thewheel housings are also thoroughlyrinsed out.Clean edges and folds on openeddoors and the bonnet as well as theareas they cover.Have the door hinges of all doorsgreased by a workshop.Do not clean the engine compartmentwith a steam-jet or high-pressure jetcleaner.On vehicles emblem touchpad: whencleaning with a high-pressure jetcleaner ensure a minimum distanceof 12 inches when working around thetailgate to prevent unintendedunlocking.

Thoroughly rinse and leather-off thevehicle. Rinse leather frequently. Useseparate leathers for painted andglass surfaces: remnants of wax onthe windows will impair vision.

Exterior lightsHeadlight and other light covers aremade of plastic. Do not use anyabrasive or caustic agents, do not usean ice scraper, and do not clean themdry.

Polishing and waxingWax the vehicle regularly (at thelatest when water no longer beads).Otherwise, the paintwork will dry out.Polishing is necessary only if the painthas become dull or if solid depositshave become attached to it.Paintwork polish with silicone formsa protective film, making waxingunnecessary.Plastic body parts must not be treatedwith wax or polishing agents.

192 Vehicle care

Windows and windscreen wiperbladesUse a soft lint-free cloth or chamoisleather together with window cleanerand insect remover.When cleaning the rear window,make sure the heating element insideis not damaged.For mechanical removal of ice, usea sharp-edged ice scraper. Press thescraper firmly against the glass sothat no dirt can get under it andscratch the glass.Clean smearing wiper blades witha soft cloth and window cleaner.

Glass panelNever clean with solvents or abrasiveagents, fuels, aggressive media (e.g.paint cleaner, acetone-containingsolutions etc.), acidic or highlyalkaline media or abrasive pads. Donot apply wax or polishing agents tothe glass panel.

Wheels and tyresDo not use high-pressure jetcleaners.

Clean rims with a pH-neutral wheelcleaner.Rims are painted and can be treatedwith the same agents as the body.

Paintwork damageRectify minor paintwork damage witha touch-up pen before rust forms.Have more extensive damage or rustareas repaired by a workshop.

UnderbodySome areas of the vehicle underbodyhave a PVC undercoating while othercritical areas have a durableprotective wax coating.After the underbody is washed, checkthe underbody and have it waxed ifnecessary.Bitumen/rubber materials coulddamage the PVC coating. Haveunderbody work carried out bya workshop.Before and after winter, wash theunderbody and have the protectivewax coating checked.

Towing equipmentDo not clean the coupling ball bar witha steam-jet or high-pressure jetcleaner.

Rear carrier systemClean the rear carrier system witha steam-jet or high-pressure jetcleaner at least once a year.Operate the rear carrier systemperiodically if not in regular use, inparticular during winter.

Air shutterClean the shutter system in the frontbumper to maintain correctfunctionality.

Interior careInterior and upholsteryOnly clean the vehicle interior,including the instrument panel fasciaand panelling, with a dry cloth orinterior cleaner.Clean the leather upholstery withclear water and a soft cloth. In case ofheavy soiling, use leather care.

Vehicle care 193

The instrument panel should only becleaned using a soft damp cloth.Clean fabric upholstery witha vacuum cleaner and brush.Remove stains with an upholsterycleaner.Clean seat belts with lukewarm wateror interior cleaner.

Caution

Close Velcro fasteners as openVelcro fasteners on clothing coulddamage seat upholstery.The same applies to clothing withsharp-edged objects, like zips orbelts or studded jeans.

Plastic and rubber partsPlastic and rubber parts can becleaned with the same cleaner asused to clean the body. Use interiorcleaner if necessary. Do not use anyother agent. Avoid solvents and petrolin particular. Do not use high-pressure jet cleaners.

194 Service and maintenance

Service andmaintenance

General information ................... 194Recommended fluids, lubricantsand parts .................................... 195

General informationService informationIn order to ensure economical andsafe vehicle operation and tomaintain the value of your vehicle, itis of vital importance that allmaintenance work is carried out at theproper intervals as specified.The detailed, up-to-date serviceschedule for your vehicle is availableat the workshop.Service display 3 71.

European service intervalsMaintenance of your vehicle isrequired every 20,000 miles or after1 year, whichever occurs first, unlessotherwise indicated in the servicedisplay.The European service intervals arevalid for the following countries:Andorra, Austria, Belgium, Bosnia-Herzegovina, Bulgaria, Croatia,Cyprus, Czech Republic, Denmark,Estonia, Finland, France, Germany,Greece, Greenland, Hungary,

Iceland, Ireland, Israel, Italy, Latvia,Lithuania, Luxembourg, Macedonia,Malta, Montenegro, Netherlands,Norway, Poland, Portugal, Romania,Slovakia, Slovenia, Spain, Sweden,Switzerland, United Kingdom.Service display 3 71.

International service intervalsMaintenance of your vehicle isrequired every 10,000 miles or after1 year, whichever occurs first, unlessotherwise indicated in the servicedisplay.The international service intervals arevalid for the countries which are notlisted in the European serviceintervals.Service display 3 71.

ConfirmationsConfirmation of service is recorded inthe Service and Warranty Booklet.The date and mileage is completedwith the stamp and signature of theservicing workshop.

Service and maintenance 195

Make sure that the Service andWarranty Booklet is completedcorrectly as continuous proof ofservice is essential if any warranty orgoodwill claims are to be met, and isalso a benefit when selling thevehicle.

Service interval with remainingengine oil life durationThe service interval is based onseveral parameters depending onusage.The service display lets you knowwhen to change the engine oil.Service display 3 71.

Recommended fluids,lubricants and partsRecommended fluids andlubricantsOnly use products that meet therecommended specifications.Damage resulting from the use ofproducts not in line with thesespecifications will not be covered bythe warranty.

9 Warning

Operating materials arehazardous and could bepoisonous. Handle with care. Payattention to information given onthe containers.

Engine oilEngine oil is identified by its qualityand its viscosity. Quality is moreimportant than viscosity whenselecting which engine oil to use. Theoil quality ensures e.g. enginecleanliness, wear protection and oil

aging control, whereas viscositygrade gives information on the oil'sthickness over a temperature range.Dexos is the newest engine oil qualitythat provides optimum protection forgasoline and diesel engines. If it isunavailable, engine oils of other listedqualities have to be used.Recommendations for gasolineengines are also valid forCompressed Natural Gas (CNG),Liquified Petroleum Gas (LPG) andEthanol (E85) fuelled engines.Select the appropriate engine oilbased on its quality and on theminimum ambient temperature3 199.

Topping up engine oilEngine oils of different manufacturersand brands can be mixed as long asthey comply with the required engineoil quality and viscosity.Use of engine oil with onlyACEA A1/B1 or only A5/B5 quality isprohibited, since it can cause long-term engine damage under certainoperating conditions.

196 Service and maintenance

Select the appropriate engine oilbased on its quality and on theminimum ambient temperature3 199.

Additional engine oil additivesThe use of additional engine oiladditives could cause damage andinvalidate the warranty.

Engine oil viscosity gradesThe SAE viscosity grade givesinformation of the thickness of the oil.Multigrade oil is indicated by twofigures, e.g. SAE 5W-30. The firstfigure, followed by a W, indicates thelow temperature viscosity and thesecond figure the high temperatureviscosity.Select the appropriate viscosity gradedepending on the minimum ambienttemperature 3 199.All of the recommended viscositygrades are suitable for high ambienttemperatures.

Coolant and antifreezeUse only organic acid type-long lifecoolant (LLC) antifreeze approved forthe vehicle. Consult a workshop.The system is factory filled withcoolant designed for excellentcorrosion protection and frostprotection down to approx. -28 °C. Innorthern countries with very lowtemperatures the factory filled coolantprovides frost protection down toapprox. -37°C. This concentrationshould be maintained all year round.The use of additional coolantadditives that intend to give additionalcorrosion protection or seal againstminor leaks can cause functionproblems. Liability for consequencesresulting from the use of additionalcoolant additives will be rejected.

Brake and clutch fluidOnly use high-performance brakefluid approved for the vehicle, consulta workshop.

Over time, brake fluid absorbsmoisture which will reduce brakingeffectiveness. The brake fluid shouldtherefore be replaced at the specifiedinterval.Brake fluid should be stored ina sealed container to avoid waterabsorption.Ensure brake fluid does not becomecontaminated.

Technical data 197

Technical data

Vehicle identification .................. 197Vehicle data ............................... 199

Vehicle identificationVehicle IdentificationNumber

The Vehicle Identification Number isvisible through the windscreen.

Identification plate

The identification plate is located onthe front left door frame.

198 Technical data

Information on identification label:1 = Manufacturer2 = Type approval number3 = Vehicle Identification Number4 = Permissible gross vehicle

weight rating in kg5 = Permissible gross train weight

in kg6 = Maximum permissible front axle

load in kg7 = Maximum permissible rear axle

load in kg8 = Vehicle-specific or country-

specific data

The combined total of front and rearaxle loads must not exceed thepermissible gross vehicle weight. Forexample, if the front axle is bearing itsmaximum permissible load, the rearaxle can only bear a load that is equalto the gross vehicle weight minus thefront axle load.The technical data is determined inaccordance with EuropeanCommunity standards. We reservethe right to make modifications.

Specifications in the vehicledocuments always have priority overthose given in this manual.

Technical data 199

Vehicle dataRecommended fluids and lubricantsEuropean service schedule

Required engine oil qualityAll European countries

(except Belarus, Moldova, Russia, Serbia, Turkey) Only Israel

Engine oil quality Petrol engines(including CNG, LPG, E85)

Diesel engines Petrol engines(including CNG, LPG, E85)

Diesel engines

dexos 1 – – ✔ –

dexos 2 ✔ ✔ – ✔

In case dexos quality is unavailable you may use max. 1 litre engine oil quality ACEA C3 once between each oil change.

Engine oil viscosity gradesAll European countries and Israel(except Belarus, Moldova, Russia, Serbia, Turkey)

Ambient temperature Petrol and diesel engines

down to -25 °C SAE 5W-30 or SAE 5W-40

below -25 °C SAE 0W-30 or SAE 0W-40

200 Technical data

International service schedule

Required engine oil qualityAll countries outside Europe

except Israel Only Belarus, Moldova, Russia, Serbia, Turkey

Engine oil quality Petrol engines(including CNG, LPG, E85)

Diesel engines Petrol engines(including CNG, LPG, E85)

Diesel engines

dexos 1 ✔ – – –

dexos 2 – ✔ ✔ ✔

In case dexos quality is unavailable you may use the oil qualities listed below:

All countries outside Europeexcept Israel Only Belarus, Moldova, Russia, Serbia, Turkey

Engine oil quality Petrol engines(including CNG, LPG, E85)

Diesel engines Petrol engines(including CNG, LPG, E85)

Diesel engines

GM-LL-A-025 ✔ – ✔ –

GM-LL-B-025 – ✔ – ✔

Technical data 201

All countries outside Europeexcept Israel Only Belarus, Moldova, Russia, Serbia, Turkey

Engine oil quality Petrol engines(including CNG, LPG, E85)

Diesel engines Petrol engines(including CNG, LPG, E85)

Diesel engines

ACEA A3/B3 ✔ – ✔ –

ACEA A3/B4 ✔ ✔ ✔ ✔

ACEA C3 ✔ ✔ ✔ ✔

API SM ✔ – ✔ –

API SN resource conserving ✔ – ✔ –

Engine oil viscosity gradesAll countries outside Europe (except Israel),including Belarus, Moldova, Russia, Serbia, Turkey

Ambient temperature Petrol and diesel engines

down to -25 °C SAE 5W-30 or SAE 5W-40

below -25 °C SAE 0W-30 or SAE 0W-40

down to -20 °C SAE 10W-301) or SAE 10W-401)

1) Permitted, but usage of SAE 5W-30 or SAE 5W-40 with dexos quality is recommended.

202 Technical data

Engine dataSales designation 1.4 1.4 1.4 1.6 2.0 TurboEngine identifier code A14XER A14NEL A14NET A16LET A20DTH

Number of cylinders 4 4 4 4 4

Piston displacement [cm3] 1398 1364 1364 1598 1956

Engine power [kW] 74 88 103 132 121

at rpm 6000 4200-6000 4900-6000 5500 4000

Torque [Nm] 130 200 200 230 350

at rpm 4000 1850-4200 1850-4900 2200- 5400 1750-2500

Fuel type Petrol Petrol Petrol Petrol Diesel

Octane rating RON

recommended 95 95 95 95 –

possible 98 98 98 98 –

possible 91 91 91 91 –

Oil consumption [l/1000 km] 0.6 0.6 0.6 0.6 0.6

Technical data 203

PerformanceEngine A14XER A14NEL A14NET A16LET A20DTH

Maximum speed2) [mph]

Manual transmission 111 119 125 137 131

Automatic transmission – – 124 – 129

Vehicle weightKerb weight, basic model without any optional equipment

Engine Manual transmission Automatic transmission

with air conditioning[kg]

A14XER 1437 –

A14NEL 1437 –

A14NET 1437 –

A16LET 1471 –

A20DTH 1550 –

2) The maximum speed indicated is achievable at kerb weight (without driver) plus 200 kg payload. Optional equipmentcould reduce the specified maximum speed of the vehicle.

204 Technical data

Kerb weight, basic model with all optional equipmentEngine Manual transmission Automatic transmission

with air conditioning[kg]

A14XER 1571 –

A14NEL 1571 –

A14NET 1571 –

A16LET 1613 –

A20DTH 1701 –

Vehicle dimensions

Length [mm] 4466

Width without exterior mirrors [mm] 1840

Width with two exterior mirrors [mm] 2020

Height (without antenna) [mm] 1482

Length of load compartment floor [mm] 855

Length of load compartment with folded rear seats [mm] 1617

Load compartment width [mm] 980

Load compartment height [mm] 512

Technical data 205

Wheelbase [mm] 2695

Turning circle diameter [m] 11.4

CapacitiesEngine oilEngine A14XER A14NEL,

A14NETA16LET A20DTH

including Filter [l] 4.0 4.0 4.5 4.5

between MIN and MAX [l] 1.0 1.0 1.0 1.0

Fuel tankPetrol/diesel, nominal capacity [l] 56

206 Technical data

Tyre pressuresComfort with up to 3 people ECO with up to 3 people With full load

Engine Tyres front rear front rear front rear[kPa/bar]([psi])

[kPa/bar]([psi])

[kPa/bar]([psi])

[kPa/bar]([psi])

[kPa/bar]([psi])

[kPa/bar]([psi])

A14XER 225/55 R17, 210/2.1 (30) 210/2.1 (30) 250/2.5 (36) 250/2.5 (36) 220/2.2 (32) 260/2.6 (38)

235/50 R18,

235/55 R17,

245/45 R18

A14NEL,A14NET

225/55 R17, 210/2.1 (30) 210/2.1 (30) 270/2.7 (39) 270/2.7 (39) 220/2.2 (32) 270/2.7 (39)

235/45 R19,

235/50 R18,

235/55 R17,

245/40 R20,

245/45 R18

Technical data 207

Comfort with up to 3 people ECO with up to 3 people With full loadEngine Tyres front rear front rear front rear

[kPa/bar]([psi])

[kPa/bar]([psi])

[kPa/bar]([psi])

[kPa/bar]([psi])

[kPa/bar]([psi])

[kPa/bar]([psi])

A16LET 225/55 R17, 210/2.1 (30) 210/2.1 (30) 250/2.5 (36) 250/2.5 (36) 220/2.2 (32) 260/2.6 (38)

235/45 R19,

235/50 R18,

235/55 R17,

245/40 R20,

245/45 R18

A20DTH 225/55 R17, 230/2.3 (33) 230/2.3 (33) 270/2.7 (39) 270/2.7 (39) 240/2.4 (35) 280/2.8 (41)

235/45 R19,

235/50 R18,

235/55 R17,

245/40 R20,

245/45 R18

All Temporary spare wheel 420/4.2 (61) 420/4.2 (61) – – 420/4.2 (61) 420/4.2 (61)

208 Technical data

Towing hitch installation dimensions

Customer information 209

Customer information

Vehicle data recording andprivacy ....................................... 209

Vehicle data recordingand privacyEvent data recordersThe vehicle has a number ofsophisticated systems that monitorand control several vehicle data.Some data may be stored duringregular operation to facilitate repair ofdetected malfunctions, other data isstored only in a crash or near crashevent by modules in your vehiclesystems that have an event datarecording function such as the airbagcontrol module.The systems may record diagnosticdata about the condition of the vehicle(e.g. oil level or vehicle mileage) andinformation how it was operated (e.g.engine speed, brake application andseat belt usage).To read this data, special equipmentand access to the vehicle is required.Some diagnostic data is electronicallyfed into Vauxhall global systemswhen the vehicle is serviced ina workshop, in order to document the

service history of the vehicle. Thisenables the workshop to offer youefficient maintenance and repair,tailored to your individual vehicle,each time you bring it back to theworkshop.The manufacturer will not accessdriver's behaviour related informationabout a crash event or share it withothers except:■ with the consent of the vehicle

owner or, if the vehicle is leased, ofthe lessee

■ in response to an official request ofpolice or similar government office

■ as part of the manufacturer'sdefense in case of legalproceedings

■ as required by law

210 Customer information

In addition, the manufacturer may usethe collected or received diagnosticdata:■ for the manufacturer's research

needs■ to make it available for research

needs where appropriateconfidentiality is maintained andneed is shown

■ to share summary data which is nottied to a specific vehicle with otherorganisations for researchpurposes

Radio FrequencyIdentification (RFID)RFID technology is used in somevehicles for functions such as tyrepressure monitoring and ignitionsystem security. It is also used inconnection with conveniences suchas radio remote controls for doorlocking/unlocking and starting, and in-vehicle transmitters for garage dooropeners. RFID technology inVauxhall vehicles does not use orrecord personal information or linkwith any other Vauxhall systemcontaining personal information.

Customer information 211

212

Index AAccessories and vehicle

modifications .......................... 154Active head restraints................... 34Adaptive forward lighting ..........

.................................. 79, 100, 164Adjustable air vents ................... 116Airbag and belt tensioners ........... 74Airbag deactivation ................ 44, 74Airbag system .............................. 41Air conditioning regular

operation ................................ 117Air conditioning system .............. 111Air intake .................................... 117Air vents...................................... 116Antilock brake system ................ 129Antilock brake system (ABS) ....... 76Anti-theft alarm system ................ 25Anti-theft locking system .............. 25Appearance care........................ 191Armrest................................... 38, 39Armrest storage ........................... 53Ashtrays ....................................... 68Automatic anti-dazzle .................. 29Automatic light control ................. 98Automatic locking ........................ 23Automatic transmission ............. 125Auxiliary heater........................... 116

BBattery ....................................... 159Battery discharge protection ...... 108Battery voltage ............................. 88Bonnet ....................................... 155Brake and clutch fluid................. 195Brake and clutch system ............. 75Brake assist ............................... 131Brake fluid .................................. 158Brakes ............................... 129, 158Breakdown.................................. 189Bulb replacement ....................... 162

CCapacities .................................. 205Car Pass ...................................... 19Catalytic converter ..................... 124Central locking system ................ 21Centre console lighting .............. 107Centre console storage ............... 53Changing tyre and wheel size . . . 178Charging system .......................... 75Child restraint installation

locations ................................... 47Child restraint systems ................ 45Cigarette lighter ........................... 68Climate control ............................. 15Climate control systems............. 110Clock............................................. 67

213

Code............................................. 85Control indicators.......................... 71Control of the vehicle ................. 118Controls........................................ 62Convex shape .............................. 27Coolant and antifreeze............... 195Cruise control ...................... 79, 135Cupholders .................................. 51Curtain airbag system .................. 43Curve lighting.............................. 100

DDanger, Warnings and Cautions . . . 3Diesel fuel system bleeding ....... 161Diesel particle filter............... 77, 123Door open .................................... 80Doors............................................ 23Driver assistance systems.......... 135Driver Information Centre............. 80Driving characteristics and

towing tips .............................. 149Driving hints................................ 118

EElectric adjustment ...................... 27Electrical parking brake................ 76Electrical parking brake fault........ 76Electrical system......................... 170Electronic climate control

system .................................... 112

Electronic driving programmes . . 127Electronic Stability Control.......... 132Electronic Stability Control and

Traction Control system............ 77Electronic Stability Control off....... 77End-of-life vehicle recovery ....... 155Engine compartment fuse box ... 171Engine coolant ........................... 157Engine coolant temperature

gauge ....................................... 70Engine data ............................... 202Engine exhaust .......................... 123Engine oil ................... 156, 195, 199Engine oil pressure ...................... 78Entry lighting .............................. 107Event data recorders.................. 209Exit lighting ................................ 108Exterior care .............................. 191Exterior light ................................. 79Exterior lighting ...................... 12, 97Exterior mirrors............................. 27

FFault ........................................... 127First aid......................................... 60First aid kit ................................... 60Fixed air vents ........................... 116Fog light ....................................... 79Fog lights ................................... 166Folding ......................................... 28

Following distance indication...... 137Front airbag system ..................... 42Front fog lights ........................... 105Front seats.................................... 35Front storage................................ 52Fuel............................................. 146Fuel consumption - CO2-

Emissions ............................... 148Fuel for diesel engines .............. 147Fuel for petrol engines ............... 146Fuel gauge ................................... 70Fuses ......................................... 170

GGauges......................................... 69General information ................... 149Glovebox ..................................... 51Graphic-Info-Display, Colour-

Info-Display .............................. 83

HHalogen headlights .................... 162Hand brake......................... 129, 130Hazard warning flashers ............ 104Headlight flash ............................. 99Headlight range adjustment ........ 99Headlights..................................... 97Headlights when driving abroad 100Head restraint adjustment ............. 8Head restraints ............................ 33

214

Heated ......................................... 28Heated rear window ..................... 31Heated steering wheel ................. 63Heating ........................................ 38Heating and ventilation system . 110Height adjustable rear floor cover 57High beam ............................. 79, 98High beam assist.................... 79, 98Hill start assist ........................... 131Horn ....................................... 13, 63

IIdentification plate ..................... 197Ignition switch positions ............. 119Immobiliser ............................ 27, 79Indicators...................................... 69Information displays...................... 80Instrument cluster ........................ 69Instrument panel fuse box ......... 173Instrument panel illumination ..... 169Instrument panel illumination

control .................................... 106Instrument panel overview ........... 10Interactive driving system........... 133Interior care ............................... 192Interior lighting............................ 106Interior lights ...................... 106, 169Interior mirrors.............................. 29Interruption of power supply ...... 127

Introduction .................................... 3ISOFIX child restraint systems .... 50

JJump starting ............................. 187

KKey, memorised settings.............. 21Keys ............................................. 19Keys, locks................................... 19

LLane departure warning....... 77, 143Lashing eyes ............................... 59Lighting features......................... 107Light switch .................................. 97Load compartment ................ 23, 54Load compartment cover ............. 56Load compartment fuse box ...... 174Loading information ..................... 60Low fuel ....................................... 78Low washer fluid .......................... 79

MMalfunction indicator light ............ 75Manual anti-dazzle ...................... 29Manual mode ............................. 126Manual transmission .................. 128Memorised settings...................... 21

Mirror adjustment ........................... 9Misted light covers ..................... 106

NNew vehicle running-in .............. 119Number plate light ..................... 169

OObject detection systems........... 138Odometer ..................................... 69Oil, engine.......................... 195, 199Outside temperature .................... 66Overrun cut-off ........................... 120

PParking ................................ 17, 123Parking assist ............................ 138Parking brake ............................ 130Parking lights ............................. 105Particulate filter........................... 123Performance .............................. 203Performing work ........................ 155Pollen filter ................................. 117Power outlets ............................... 68Power steering.............................. 76Power windows ............................ 30Preheating ................................... 77Puncture..................................... 182

215

QQuickheat................................... 116

RRadio Frequency Identification

(RFID)..................................... 210Radio remote control ................... 20Reading lights ............................ 107Rear floor storage cover .............. 57Rear fog light ............................... 79Rear fog lights ........................... 105Rear seats.................................... 39Rear storage................................. 56Rear window wiper/washer .......... 66Recommended fluids and

lubricants ........................ 195, 199Reduced engine power................ 79Refuelling ................................... 147Retained power off..................... 119Reversing lights ......................... 106Ride control systems.................. 132Roof rack ..................................... 60

SSeat adjustment ....................... 7, 35Seat belt ........................................ 8Seat belt reminder ....................... 74Seat belts ..................................... 39Seat folding .................................. 38Seat position ................................ 35

Selector lever ............................. 125Service ............................... 117, 194Service display ............................ 71Service information .................... 194Service vehicle soon .................... 75Side airbag system ...................... 43Sidelights...................................... 97Side turn signal lights ................ 169Spare wheel ............................... 184Speed limiter............................... 136Speedometer ............................... 69Starting and operating................ 119Starting off ................................... 16Starting the engine .................... 119Steering wheel adjustment ...... 9, 62Steering wheel controls ............... 62Stop-start system........................ 121Storage......................................... 51Storage compartments................. 51Sunglasses storage ..................... 52Sunvisor lights ........................... 107Sun visors .................................... 31Symbols ......................................... 4

TTachometer ................................. 70Tail lights ................................... 167Three-point seat belt .................... 40Tools .......................................... 176Top-tether fastening eyes ............ 50

Towing................................ 149, 189Towing another vehicle ............. 190Towing equipment ..................... 150Towing hitch installation

dimensions ............................. 208Towing the vehicle ..................... 189Traction Control system ............. 132Traction Control system off........... 77Traffic sign assistant................... 140Trailer coupling........................... 149Trailer stability assist ................. 153Trailer towing ............................. 150Transmission ............................... 16Transmission display ................. 125Tread depth ............................... 177Trip computer .............................. 89Trip odometer .............................. 69Turn and lane-change signals ... 104Turn signal ................................... 74Tyre chains ................................ 178Tyre designations ...................... 177Tyre pressure ............................ 177Tyre pressure monitoring

system............................... 78, 144Tyre pressures ........................... 206Tyre repair kit ............................. 179

216

UUltrasonic parking assist .............. 77Upshift.......................................... 76Using this manual .......................... 3

VVehicle checks............................ 155Vehicle data................................ 199Vehicle data recording and

privacy..................................... 209Vehicle dimensions .................... 204Vehicle Identification Number .... 197Vehicle jack................................ 176Vehicle messages ....................... 85Vehicle personalisation ............... 92Vehicle security............................ 25Vehicle specific data ...................... 3Vehicle storage........................... 154Vehicle tools............................... 176Vehicle unlocking ........................... 6Vehicle weight ........................... 203Ventilation................................... 110

WWarning chimes ........................... 88Warning lights............................... 69Warning triangle .......................... 59Washer and wiper systems ......... 14Washer fluid ............................... 158Wheel changing ......................... 182

Wheel covers ............................. 178Wheels and tyres ....................... 176Windows....................................... 29Windscreen................................... 29Windscreen wiper/washer ........... 64Winter tyres ............................... 176Wiper blade replacement .......... 161