· web viewansi/ul 10c - standard for safety for positive pressure fire tests of door assemblies....

SECTION 08 71 53DOOR HARDWARE

Display hidden notes to specifier. (Don't know how? Click Here)

Copyright 2008 - 2017 ARCAT, Inc. - All rights reserved

PART 1 GENERAL

1.1 SECTION INCLUDES

A. Door hardware of the following types:1. Mortise locksets.2. Cylindrical locksets - Grade 1.3. Cylindrical locksets - Grade 2.4. Cylindrical locksets - Grade 2, standard duty.5. Tubular locksets - Grade 2.6. Inter-connected locksets - Grade 2.7. Cylindrical locksets - Grade 3.8. Deadbolts.9. Door controls.10. Exit devices.

1.2 RELATED SECTIONS

A. Section 05 10 00 - Structural Metal Framing.

B. Section 06 10 00 - Rough Carpentry.

C. Section 07 84 13 - Penetration Firestopping Mortars.

D. Section 08 11 00 - Metal Doors and Frames.

E. Section 08 11 10 - Metal Doors and Frames.

F. Section 08 41 23 - Steel-Framed Entrances and Storefronts.

G. Section 08 71 70 - Weatherstripping and Seals*.

H. Section 16 00 00 - Electrical.

1.3 REFERENCES

A. ANSI/DHI A115.1 - Mortise Lock Preparation.

B. ICC/ANSI A117.1 - American National Standard for Accessible and Useable Buildings and Facilities.

C. ANSI/BHMA A156.2 - American National Standard for Bored and Preassembled Locks & Latches

D. ANSI/BHMA A156.3 - American National Standard for Exit Devices

08 71 00-1

E. ANSI/BHMA A156.4 - American National Standard for Door Controls - Closers.

F. ANSI/BHMA A156.13 - American National Standard for Mortise Locks and Latches, Series 1000.

G. NFPA 80 - Standard for Fire Doors, Fire Windows.

H. NFPA 252 - Standard Methods of Fire Tests of Door Assemblies.

I. ANSI A250.13 - Testing and Rating of Severe Windstorm Resistant Components for Swinging Door Assemblies.

J. ASTM E330 - Standard Test Method for Structural Performance of Exterior Windows, Doors, Skylights and Curtain Walls by Uniform Static Air Pressure Difference.

K. ASTM E1886 - Standard Test Method for Performance of Exterior Windows, Curtain Walls, Doors, and Impact Protective Systems Impacted by Missile(s) and Exposed to Cyclic Pressure Differentials.

L. FF-H-106 - Type 86: Builder's Hardware, General Specification for Locks and Door (Lock Bodies).

M. ANSI/UL 10C - Standard for Safety for Positive Pressure Fire Tests of Door Assemblies.

N. ANSI/UL 305 - Standard for Panic Hardware

O. Underwriters Laboratories (UL). - Fire Resistance Directory.

P. Unified Facilities Guide Specification 08 71 00 (August 2008)

1.4 SUBMITTALS

A. Submit under provisions of Section 01 30 00.

B. Product Data: Manufacturer's data sheets on each product to be used, including:1. Preparation instructions and recommendations.2. Storage and handling requirements and recommendations.3. Installation methods.

C. Shop Drawings: Manufacturer's approved shop drawings are required detailing the application of each product specified.

D. Schedule:1. Submit schedule indicating each type of hardware for each door.2. List manufacturer's name with each manufacturer's hardware number together with

finishes in US or ANSI standards.3. Show door number/location, handing, door and frame material, manufacture and

catalog numbers, all finishes and keying information. Explain fully all abbreviations.

E. Selection Samples: For each finish product specified, two complete sets of color chips representing manufacturer's full range of available colors and patterns.

F. Verification Samples:1. If required by the Architect, submit one sample of each type of typical hardware

required illustrating style, color, and finish.2. Approved samples may be incorporated into Work.

G. Closeout Submittals:

08 71 00-2

1. Project Record Documents: Schedule showing actual locations of installed cylinders and their master key code.

2. Parts lists and maintenance instructions including data on operating hardware, lubrication requirements, and inspection procedures related to preventative maintenance.

3. Keys: Deliver with identifying tags to Owner by security shipment direct from hardware supplier.

1.5 QUALITY ASSURANCE

A. Manufacturer Qualifications: Equipment specified in this Section shall be provided by a single manufacturer with a minimum of ten years experience manufacturing door hardware.

B. Supplier Qualifications: A supplier with a minimum of two years demonstrated experience in the sale and distribution of builders' hardware for commercial projects and who has successfully completed at least three projects of similar complexity to the project specified.

C. Hardware Supplier Personnel: Employ Architectural Hardware Consultant (AHC) or equally qualified person to supervise and prepare all schedules, details, and services required for the project.

D. Installer Qualifications: All products listed in this Section are to be installed by a single installer with a minimum of five years demonstrated experience in installing products of the same type and scope as specified.

E. Mock-Up: Provide a mock-up for evaluation of surface preparation techniques and application workmanship.1. Finish areas designated by Architect.2. Do not proceed with remaining work until workmanship and appearance are approved

by Architect.3. Refinish mock-up area as required to produce acceptable work.

1.6 DELIVERY, STORAGE, AND HANDLING

A. Store products in manufacturer's unopened packaging until ready for installation.

1.7 PROJECT CONDITIONS

A. Maintain environmental conditions (temperature, humidity, and ventilation) within limits recommended by manufacturer for optimum results. Do not install products under environmental conditions outside manufacturer's recommended limits.

1.8 WARRANTY

A. At project closeout, provide factory warranty against defects in material and workmanship as follows:1. Overhead surface closers, Grade 1, 25 Year Warranty.2. Mortise locks, Grade 1, Limited Lifetime Warranty.3. Cylindrical locks, XGT Series Grade 1, Limited Lifetime Warranty.4. Cylindrical locks, GT Series Grade 1, 25 Year Warranty.5. Exit devices, 6200 Series Grade 1, 10 Year Warranty.6. Exit devices, 4200 Series Commercial Grade, 5 Year Warranty.7. Electrified locks and exit devices, 1 year Warranty.

1.9 MAINTENANCE MATERIALS

A. Provide special wrenches and tools applicable to each different or special hardware component.

08 71 00-3

1.10 COORDINATION

A. Coordinate work with other directly affected components involving manufacture or fabrication of internal reinforcement for door hardware and recessed items.

B. Coordinate work with other directly affected components involving electrical wiring and components.

PART 2 PRODUCTS

2.1 MANUFACTURERS

A. Acceptable Manufacturer: PDQ Mfg., which is located at: P. O. Box 507 2754 Creek Hill Rd.; Leola, PA 17540; Toll Free Tel: 800-441-9692; Tel: 717-656-4281; Fax: 717-656-6892; Email:[email protected]; Web:www.pdqlocks.com

B. Substitutions: Not permitted.

C. Requests for substitutions will be considered in accordance with provisions of Section 01 60 00.

2.2 MORTISE LOCKSETS

A. Model: MR Series Mortise Lock, Heavy Duty by PDQ Mfg.1. Country of Origin: Meets requirements of Buy American Act2. Assembled in the USA.3. Certified to ANSI/BHMA A156.13, Operational Grade 1, Security Grade 1.4. UL/ULC Listed: A-label (3 hour) swing doors, 4 ft by 8 ft (1219 mm by 2433 mm)

maximum.5. Windstorm Resistant: ANSI A250.13, ASTM E330, ASTM E1886.6. Outswing: 350 ft-lbs.7. Design Load Rating: 2453 lbf for Functions with deadbolts.8. Backset: 2-3/4 inches (70 mm)9. Case: Zinc and clear or yellow chromate.

a. Construction: Heavy Gauge Steel.b. Finish: Zinc and clear.c. Finish: Yellow chromate.d. Finish: As indicated on the Drawings.e. Finish: As selected by Architect from manufacturer's standard options.

10. Front: 8 inches (203 mm) by 1-1/4 inches (32 mm); adjustable from flat to beveled; brass or stainless steel; ANSI Standard A115.1.

11. Stop Works: Stainless steel; rocker type.12. Hubs: Sintered copper infiltrated iron.13. Strike: 4-7/8 inches (124 mm) by 1-1/4 inches (32 mm) by 3/32 inch (2.4 mm)

a. Lip: Curved, LH/RHR.b. Lip: Curved, RH/LHR.c. Lip: Extended.d. Material: Brass.e. Material: Stainless steel.

14. Latchbolt: 1-5/8 inches (41 mm) by 3/4 inch (19 mm) throw, stainless steel; anti-friction; fully retracted with 35 degree lever rotation; field reversible.

15. Deadbolt: 1 inch (25 mm) throw, stainless steel.16. Guard Bolt: Stainless steel; non-handed.17. Cylinder: 6 pin brass mortise cylinder keyed to 5 pins.

a. Length: 1-1/8 inch (29 mm).b. Length: 1-1/4 inches (32 mm).c. Cap: Brass.

08 71 00-4

d. Cap: Bronze.e. Cap: Aluminum.

18. Keys: Two per cylinder.19. Keyway: SCC standard.20. Keyway: ________.21. Interchangeable Core: 6 pin.22. Interchangeable Core: 7 pin.23. Keying:

a. Zero Bitted (KO).b. Keyed Different (KD).c. Keyed Alike (KA).d. Master Keyed (MK).e. Construction Master Keyed (CMK).f. Grand Master Keyed (GMK).g. Match existing masterkey system.

24. Warranty: Lifetime.

B. Lockset Function:1. As noted on the Contract Drawings.2. Function: ________________________________.

C. Trim:1. Material: Forged brass.2. Material: Solid stainless steel.3. Lever trim meets ANSI A117.1 and ADA requirements4. F Series Sectional Trim: Boston Lever BFSF5. F Series Sectional Trim: Philadelphia Lever PFSF.6. F Series Sectional Trim: Miami Lever MFSF.7. F Series Escutcheon Trim: Boston Lever BFEF8. F Series Escutcheon Trim: Philadelphia Lever PFEF9. F Series Escutcheon Trim: Miami Lever MFEF.10. J Series Sectional Trim: Philadelphia Lever PJSJ11. J Series Sectional Trim: Chicago Lever CJSJ12. J Series Sectional Trim: Memphis Lever TJSJ13. J Series Sectional Trim: Dallas Lever DJSJ14. J Series Sectional Trim: Orlando Lever OJSJ.15. J Series Sectional Trim: Boston Lever BJSJ16. J Series Sectional Trim: Miami Lever MJSJ17. J Series Sectional Trim: Ball Knob KJSJ.18. J Series Escutcheon Trim: Philadelphia PJEJ19. J Series Escutcheon Trim: Chicago Lever CJEJ20. J Series Escutcheon Trim: Memphis Lever TJEJ21. J Series Escutcheon Trim: Dallas Lever DJEJ22. J Series Escutcheon Trim: Orlando Lever OJEJ23. J Series Escutcheon Trim: Boston Lever BJEJ24. J Series Escutcheon Trim: Miami Lever MJEJ25. J Series Escutcheon Trim: Ball Knob KJEJ.26. JW Wide Series Escutcheon Trim: Philadelphia Lever PJEW27. JW Wide Series Escutcheon Trim: Chicago Lever CJEW28. JW Wide Series Escutcheon Trim: Memphis Lever TJEW29. JW Wide Series Escutcheon Trim: Dallas Lever DJEW30. JW Wide Series Escutcheon Trim: Orlando Lever OJEW31. JW Wide Series Escutcheon Trim: Boston Lever BJEW32. JW Wide Series Escutcheon Trim: Miami Lever MJEW.33. JW Wide Series Escutcheon Trim: Ball Knob KJEW.

08 71 00-5

D. Trim:1. Finish: As specified in the Door Hardware Schedule.2. Brass: 605 (Bright).3. Brass: 606 (Satin).4. Bronze: 612 (Satin).5. Bronze: 613 (Dark).6. Chrome 625 (Bright)7. Chrome: 626 (Satin).8. Stainless: 630 (Satin).9. Antimicrobial: AM.

2.3 CYLINDRICAL LOCKSETS - GRADE 1

A. Model: XGT Spirit Series, Extremely Heavy Duty.

B. Model: GT Spirit Series, Extra Heavy Duty.

C. Model: SX Knob Lockset, Heavy Duty.

D. Lockset Characteristics:1. XGT/GT are Assembled in the USA from U.S. and foreign materials. Product meets

the requirements of the BAA.2. SX is manufactured in a WTO designated country and therefore meets the

requirements of the BAA.3. ANSI BHMA Certified: Grade 1 ANSI A156.2 Series 4000 ANSI A156.2, Series 4000,

Operational Grade 1.4. ANSI: Grade 1.5. UL/ULC Listed: A-label (3 hour) swing doors, 4 ft by 8 ft (1219 mm by 2433 mm)

maximum.6. Certification: UL 10C/UBC 7-2 Positive Pressure Rated.7. Certification: UL 10B neutral Pressure Rated.8. Backset: 2-3/4 inches (70 mm).9. Chassis: Heavy duty zinc diecast hubs; investment cast; chromated cold rolled steel;

stainless steel and Acuzinc mechanism; billet steel spindles for locking functions.10. Front: 2-1/4 inches (57 mm) by 1-1/8 inch (29 mm); beveled 1/8 inch (3.2 mm) on 2

inches (51 mm).a. Material: Wrought brass.b. Material: Stainless steel.

11. Strike:a. Type: ASA.b. Type: T-strike.c. Type: Full lip strike.d. Material: Wrought brass.e. Material: Stainless steel.

12. Torque Resistance: Exceeds 3000 inch lbs (339 Nm).13. Torque Resistance: Exceeds 2100 inch lbs (237 Nm).14. Latchbolt: 9/16 inch (14.3 mm) throw, Deadlocking. 9/16 Latchbolt available only on

XGT and GT Product.15. Keys: Two per cylinder.16. Keyway: SCC standard.17. Keyway: ________.18. Interchangeable Core: 6 pin.19. Interchangeable Core: 7 pin.20. LFIC Schlage format. LFIC lever required; not available with SX product.21. Cylinder: 6 pin brass insert cylinder keyed to 5 pins.22. Keying:

a. Zero Bitted (KO).

08 71 00-6

b. Keyed Different (KD).c. Keyed Alike (KA).d. Master Keyed (MK).e. Construction Master Keyed (CMK).f. Grand Master Keyed (GMK).g. Match existing masterkey system.h. Construction Keyed (CK).

23. Warranty: Five year.24. Warranty: Limited 25 year warranty.25. Warranty: Limited Lifetime.

E. Lockset Function:1. As noted on the Contract Drawings.2. Function: ________________________________.

F. Trim: Solid zinc diecast; 41 degree lever rotation.1. Lever: Boston BSN; meets ADA requirements.2. Lever: Miami MIA.3. Lever: Philadelphia PHL; meets ADA requirements.4. Knob: CQ Ball Knob.


A. Lockset: GP Spirit Series, Heavy Duty.

B. Lockset: SA Spirit Series, Medium Duty.

C. Lockset: SD Series, Medium Duty.

D. Lockset Characteristics:1. ANSI Conformance: ANSI A156.2, Series 4000, Operational Grade 2.2. Windstorm Resistant: ANSI A250.13, ASTM E330, ASTM E1886.3. Outswing: 350 ft-lbs.4. Design Load Rating: 685 lbf.5. Torque Resistance: Exceeds 1600 inch lbs (181 Nm).6. Country of Origin: Meets requirements of Buy American Act/Assembled in the USA.7. UL/ULC Listed: A-label (3 hour) swing doors, 4 ft by 8 ft (1219 mm by 2433 mm)

maximum.8. Certification: UL 10C/UBC 7-2 Positive Pressure Rated.9. Certification: UL 10B neutral Pressure Rated.10. SD Series is manufactured in Republic of S. Korea, a WTO Designated country and

therefore meets the requirements of the BAA.11. Certification: BHMA Certified. This applies to all three locks.12. Backset: 2-3/4 inches (70 mm)13. Backset: 2-3/8 inches (60 mm).14. Backset: 5 inches (127 mm).15. Chassis: Heavy duty zinc diecast; investment cast; stainless steel mechanism.16. Chassis: Heavy gauge dichromated cold rolled steel mechanism.17. Front: 2-1/4 inches (57 mm) by 1-1/8 inch (29 mm); beveled 1/8 inch (3.2 mm) on 2

inches (51 mm).18. Front: 2-1/4 inches (57 mm) by 1 inch (25 mm); beveled 1/8 inch (3.2 mm) on 2 inches

(51 mm).a. Material: Wrought brass.b. Material: Stainless steel.

19. Strike:a. Type: ASA.b. Type: T-strike.

08 71 00-7

c. Type: Full lip strike.d. Material: Wrought brass.e. Material: Stainless steel.

20. Latchbolt: 1/2 inch (13 mm) throw; adjustable front for flat or beveled doors.21. Keys: Two per cylinder.22. Keyway: SCC standard.23. Keyway: ________.24. Interchangeable Core: 6 pin.25. Interchangeable Core: 7 pin.26. LFIC Schlage(r) format. Requires LFIC lever; not available on SA.27. Cylinder: 6 pin brass insert cylinder keyed to 5 pins.28. Cylinder: 6 pin brass insert cylinder.29. Keying:

a. Zero Bitted (KO).b. Keyed Different (KD).c. Keyed Alike (KA).d. Master Keyed (MK).e. Construction Master Keyed (CMK).f. Grand Master Keyed (GMK).g. Construction Keyed (CK).h. Match existing masterkey system.

30. Warranty: Eight years.31. Warranty: Five years.

E. Lockset Function:1. As noted on the Contract Drawings.2. Function: ________________________________.

F. Trim:1. GP Series: Solid zinc diecast; 65 degree lever rotation.2. SA Series: Solid zinc diecast with plastic insert.3. SD Series: Solid zinc diecast.4. Rose: Wrought brass.5. Lever: GP Series Spirit, Boston BSN; meets ADA requirements.6. Lever: GP Series Spirit, Philadelphia PHL; meets ADA requirements.7. Lever: GP Series Spirit, Miami MIA.8. Lever: SA Series Spirit, Philadelphia PHL; meets ADA requirements.9. Lever: SD Series with through bolts, Philadelphia PHL; meets ADA requirements.10. Lever: SD Series with through bolts, Boston BSN; meets ADA requirements.11. Lever: SD Series with through bolts, Miami MIA.12. Lever: SD Series with through bolts removed, Boston BSN; meets ADA requirements.13. Lever: SD Series with through bolts removed, Miami MIA.14. Lever: SD Series with through bolts removed, Philadelphia PHL; meets ADA

requirements.15. Lever: SD Series with through bolts, Memphis Lever.16. Lever: SD Series with through bolts removed, Memphis Lever.

2.5 CYLINDRICAL LOCKSETS - GRADE 2, STANDARD DUTY

A. Lockset: SV Series, Standard Duty.

B. Lockset: SW Series, Standard Duty.

C. Lockset Characteristics:1. ANSI Conformance: ANSI A156.2, Series 4000, Operational Grade 2.2. UL/ULC Listed: A-label (3 hour) swing doors, 4 ft by 8 ft (1219 mm by 2433 mm)

maximum.

08 71 00-8

3. Backset: 2-3/4 inches (70 mm)4. Backset: 2-3/8 inches (60 mm).5. Backset: 5 inches (127 mm).6. Front: 2-1/4 inches (57 mm) by 1-1/8 inch (29 mm).7. Front: 2-1/4 inches (57 mm) by 1 inch (25 mm).

a. Material: Wrought brass.b. Material: Wrought bronze.c. Material: Stainless steel.

8. Strike:a. Type: ASA.b. Type: T-strike.c. Type: Full lip strike.d. Material: Wrought brass.e. Material: Wrought bronze.f. Material: Stainless steel.

9. Latchbolt: 1/2 inch (13 mm) throw.10. Cylinder: 6 pin brass insert cylinder keyed to 5 pins.11. Keys: Two per cylinder.12. Keyway: SCC standard.13. Keyway: ________.14. Keying:

a. Zero Bitted (KO).b. Keyed Different (KD).c. Keyed Alike (KA).d. Master Keyed (MK).e. Construction Master Keyed (CMK).f. Grand Master Keyed (GMK).g. Construction Keyed (CK).

15. Warranty: One year.

D. Lockset Function:1. As noted on the Contract Drawings.2. Function: ________________________________.

E. Trim:1. Material: Stainless steel knob and rose.2. Material: Wrought brass knob and rose.3. Material: Zinc diecast lever; wrought brass rose.4. Material: Zinc diecast lever; stainless steel rose.5. Knob: Ball Knob CQ; meets ADA requirements.6. Lever: Patriot PAT; meets ADA requirements.

2.6 TUBULAR LOCKSETS - GRADE 2

A. Lockset: SE Series, Standard Duty.1. ANSI Conformance: ANSI A156.2, Series 4000, Operational Grade 2.2. UL/ULC Listed: A-label (3 hour) swing doors, 4 ft by 8 ft (1219 mm by 2433 mm)

maximum.3. Backset: Adjustable.4. Front: 2-1/4 inches (57 mm) by 1-1/8 inch (29 mm) with filler provided.5. Front: 2-1/4 inches (57 mm) by 1 inch (25 mm).

a. Material: Wrought brass.b. Material: Stainless steel.

6. Strike:a. Type: ASA.b. Type: T-strike.

08 71 00-9

c. Type: Full lip strike.d. Material: Wrought brass.e. Material: Stainless steel.

7. Latchbolt: 1/2 inch (13 mm) throw.8. Interchangeable Core: 6 pin.9. Interchangeable Core: 7 pin.10. Cylinder: 6 pin brass insert cylinder keyed to 5 pins.11. Keys: Two per cylinder.12. Keyway: SCC standard.13. Keyway: ________.14. Keying:

a. Zero Bitted (KO).b. Keyed Different (KD).c. Keyed Alike (KA).d. Master Keyed (MK).e. Construction Master Keyed (CMK).f. Grand Master Keyed (GMK).g. Construction Keyed (CK).h. Match existing masterkey system.



C. Trim:1. Zinc diecast lever; wrought brass rose.2. Zinc diecast lever; stainless steel rose.3. Lever: Washington WSH, _____handed.4. Lever: Philadelphia PHL; meets ADA requirements.

2.7 INTER-CONNECTED LOCKSETS - GRADE 2

A. Lockset: CL Series, Light Commercial.1. ANSI Conformance: ANSI A156.2, Series 4000, Operational Grade 2.2. UL/ULC Listed: A-label (3 hour) swing doors, 4 ft by 8 ft (1219 mm by 2433 mm)

maximum.3. Backset, Latchbolt: 2-3/4 inches (70 mm)4. Backset, Latchbolt: 2-3/8 inches (60 mm).5. Backset, Deadbolt: 2-3/4 inches (70 mm); UL Listed.6. Backset, Deadbolt: 2-3/8 inches (60 mm).7. Chassis: Dichromated cold rolled steel.8. Front: 2-1/4 inches (57 mm) by 1-1/8 inch (29 mm); beveled 1/8 on 2 inches (51 mm).9. Front: 2-1/4 inches (57 mm) by 1 inch (25 mm); beveled 1/8 on 2 inches (51 mm).


10. Strike:a. Type: T-strike.b. Type: ASA.c. Type: Full lip strike.d. Material: Wrought brass.e. Material: Stainless steel.

11. Latchbolt: 1/2 inch (13 mm) throw.12. Deadbolt: 1 inch (25 mm) throw; brass bolt containing one concealed 1/4 inch (6.4

mm) case hardened steel roll pin.13. Interchangeable Core: 6 pin.

08 71 00-10

14. Interchangeable Core: 7 pin.15. Cylinder: 6 pin brass insert cylinder keyed to 5 pins.16. Keys: Two per cylinder.17. Keyway: SCC standard.18. Keyway: ________.19. Keying:


20. Warranty: Two year.


C. Trim:1. Material: Stainless steel knob and escutcheon and rose.2. Material: Wrought brass knob and escutcheon and rose.3. Material: Zinc diecast lever; wrought brass escutcheon and rose.4. Material: Zinc diecast lever; stainless steel escutcheon and rose.5. Lever: Philadelphia PHL; meets ADA requirements.


A. Lockset: SR Series, Ultralight Commercial.1. ANSI Conformance: ANSI A156.2, Series 4000, Operational Grade 3.2. Backset: 2-3/4 inches (70 mm) to 2-3/8 inches (60 mm), adjustable.3. Front: 2-1/4 inches (57 mm) by 1 inch (25 mm).


4. Strike:a. Type: Full lip strike.b. Type: T-strike.c. Type: ASA.d. Material: Wrought brass.e. Material: Stainless steel.

5. Latchbolt: 1/2 inch (13 mm) throw.6. Cylinder: 5 pin brass insert cylinder.7. Keys: Two per cylinder.8. Keyway: SCC standard.9. Keyway: ________.10. Keying:



B. Lockset Function:1. As noted on the Contract Drawings.

08 71 00-11

2. Function: ________________________________.

C. Trim:1. Material: Diecast knob; stainless steel knob and rose.2. Material: Diecast knob; wrought brass knob and rose.3. Material: Diecast lever; wrought brass lever and rose.4. Material: Diecast lever; stainless steel lever and rose.5. Knob: Ball knob CQ.6. Knob: Flat knob VR.7. Lever: Lever LV; meets ADA requirements.

2.9 DEADBOLTS

A. Deadbolt: KT Series, Extra Heavy Duty Commercial Grade.1. Country of Origin: Meets requirements of Buy American Act.

B. Deadbolt: KM Series, Heavy Duty Commercial Grade.1. UL/ULC Listed: A-label (3 hour) swing doors, 4 ft by 8 ft (1219 mm by 2433 mm)

maximum.2. Certification: UL 10C/UBC 7-2 Positive Pressure Rated.3. Certification: UL 10B neutral Pressure Rated.

C. Deadbolt: KV Series, Standard Duty Commercial Grade.1. Certification: UL 10C/UBC 7-2 Positive Pressure Rated.2. Certification: UL 10B neutral Pressure Rated.

D. Deadbolt: KR Series, Ultra-Light Duty Commercial Grade.1. ANSI Conformance: ANSI A156.5, Grade 3 Deadbolt.

E. Deadbolt Characteristics:1. Faceplate, UL Listed: 2-1/4 inches (57 mm) by 1-1/8 inch (29 mm) with backset of 2-

3/4 inch (70 mm)2. Faceplate: 2-1/4 inches (57 mm) by 1 inch (25 mm) with backset of 2-3/8 inches (60

mm).3. Faceplate: 2-1/4 inches (57 mm) by 1 inch (25 mm) with adjustable backset of 2-3/4

inches (70 mm) to 2-3/8 inches (60 mm).a. Material: Wrought brass.b. Material: Stainless steel.

4. Strike: 2-3/4 inches (70 mm) by 1-1/8 inches (29 mm)a. Material: Wrought brass.b. Material: Stainless steel.

5. Deadbolt: 1 inch (25 mm) throw; brass bolt containing one concealed 1/4 inch (6.4 mm) case hardened steel roll pin.

6. Interchangeable Core: 6 pin.7. Interchangeable Core: 7 pin.8. Cylinder: 6 pin brass mortise cylinder keyed to 5 pins.9. Cylinder: 6 pin brass insert cylinder keyed to 5 pins.10. Cylinder: 5 pin brass rim cylinder.11. Keys: Two per cylinder.12. Keyway: SCC standard.13. Keyway: ________.14. Keying:

a. Zero Bitted (KO).b. Keyed Different (KD).c. Keyed Alike (KA).d. Master Keyed (MK).e. Construction Master Keyed (CMK).

08 71 00-12

f. Grand Master Keyed (GMK).g. Construction Keyed (CK).h. Match existing masterkey system.


F. Deadbolt Function:1. As noted on the Contract Drawings.2. Function: ________________________________.

G. Deadbolt Trim:1. Material: Wrought brass scalp with reinforced diecast rose.2. Material: Stainless steel scalp with reinforced diecast rose.3. KT Series.4. KT Series IC.5. KM Series.6. KM Series IC, _____ handed.7. KV Series.8. KV Series IC, _____ handed.9. KR Series.

2.10 LOCKSET OPTIONS

A. Options: Provide the following options where indicated on Hardware Schedule:1. Handicap Abrasive Coating: Inside and outside.

a. Inside and outside.b. Inside only.c. Outside only.

2. Lead lined rose.3. Dust box.4. Security head screws.5. Request to exit for electrified Function 199.6. Sectional single sided mounting assembly.7. Cylinder marking.8. Visual Key Control: Key marking.9. Visual Key Control: Key marking other than keyset.10. Visual Key Control: Cylinder marking.11. Dummy construction cores, plastic.

2.11 FINISH - LOCKSETS AND DEADBOLTS

A. Plated: Provide the following BHMA finish:1. 605: Bright Brass, Clear Coated.2. 606: Satin Brass, Clear Coated.3. 612: Satin Bronze, Clear Coated.4. 613: Oil Rubbed Bronze, Oxidized and Oil Rubbed, No Coating.5. 625: Bright Chrome Plated, No Coating.6. 626: Satin Chrome Plated, No Coating.7. 629: Bright Stainless Steel, No Coating.8. 630: Satin Stainless Steel, No Coating.9. Split Finish: _____ inside; _____ outside.10. Special Order: _____.

2.12 DOOR CONTROLS

A. Storefront Commercial Door Control: American Eagle 1100 Series.1. ANSI/BHMA Certified: ANSI A156.4 Grade 1.2. Certification: UL/ULC Listed.

08 71 00-13

3. Certification: UL 10C and UBC 7.2: Complies with positive pressure requirements.4. Manufactured in a WTO designated country therefore meets the requirements of the

BAA.5. Handing: Non-handed.6. Operation: Rack and pinion.7. Body: Cast aluminum.8. Backcheck: Adjustable hydraulic backcheck; separate sweep, latch and backcheck

intensity valves.9. Adjustable Spring Size: 3 through 6.10. Mounting: Tri-pack for regular, top jamb and parallel arm installations; 9-1/16 inch

(230 mm) by 3/4 inch (19 mm) mounting hole pattern; sex nuts and bolts.11. Arm: Regular Arm, RA; flat, stamped.12. Application: Tri-Pack, PA.13. Application: Hold Open, Tri-Pack, HO.14. Application: Door Saver Arm, DS.15. Application: Door Saver Hold Open Arm, DSHO.16. Finish: As specified in the Door Hardware Schedule.17. Finish, Painted: 689 - Aluminum.18. Finish, Painted: 695 - Duro Bronze.19. Finish, Painted: 696 - Gold.20. Accessories/Options: Provide the following:

a. Parallel Arm Bracket, PA.b. Parallel Arm Hold Open Bracket, PAHO.c. Back Plate, BP.d. Drop Plate, DP.e. Angle Bracket, AB.f. Narrow Frame Bracket, NFB.g. Streamline Cover, SV.

21. Warranty: Five years.

B. Commercial Door Control: American Eagle 3100 Series.1. ANSI/BHMA Certified: ANSI A156.4 Grade 1.2. Certification: UL/ULC Listed.3. Certification: UL 10C and UBC 7.2: Complies with positive pressure requirements.4. Manufactured in a WTO designated country therefore meets the requirements of the

BAA.5. Handing: Non-handed.6. Operation: Rack and pinion.7. Body: Cast aluminum.8. Backcheck: Adjustable hydraulic backcheck; separate sweep, latch and backcheck

intensity valves.9. Adjustable Spring Size: 1 through 4; meets ADA requirements.10. Adjustable Spring Size: 3 through 6.11. Mounting: Tri-pack for regular, top jamb and parallel arm installations; 9-1/16 inch

(230 mm) by 3/4 inch (19 mm) mounting hole pattern; sex nuts and bolts.12. Arm: Regular Arm, RA; flat, stamped.13. Application: Tri-Pack, PA.14. Application: Hold Open, Tri-Pack, HO.15. Application: Door Saver Arm, DS.16. Application: Door Saver Hold Open Arm, DSHO.17. Finish: As specified in the Door Hardware Schedule.18. Finish, Painted: 689 - Aluminum.19. Finish, Painted: 695 - Duro Bronze.20. Finish, Painted: 696 - Gold.21. Accessories/Options: Provide the following:

a. Parallel Arm Bracket, PA.

08 71 00-14

b. Parallel Arm Hold Open Bracket, PAHO.c. Back Plate, BP.d. Drop Plate, DP.e. Angle Bracket, AB.f. Narrow Frame Bracket, NFB.g. Streamline Cover, SV.


C. Architectural Style Commercial Door Control: American Eagle 5100 Series.1. ANSI Conformance: ANSI A156.4 Grade 1.2. Certification: UL/ULC Listed.3. Certification: UL 10C and UBC 7.2: Complies with positive pressure requirements.4. Manufactured in a WTO designated country therefore meets the requirements of the

BAA.5. Handing: Non-handed.6. Operation: Rack and pinion.7. Body: Heavy duty cast aluminum.8. Backcheck: Adjustable hydraulic backcheck; separate sweep, latch and backcheck

intensity valves.a. Provide adjustable delayed action from maximum opening to 70 degrees.

9. Adjustable Spring Size: 1 through 6; meets ANSI A117.1 and ADA requirements. Designed to provide adjustable opening force, can meet Barrier Free Opening Force Requirements.

10. Mounting: Tri-pack for regular, top jamb and parallel arm installations; 11-1/8 inch (282 mm) by 3/4 inch (19 mm) mounting hole pattern; sex nuts and bolts.

11. Arm: Regular Arm, RA; flat, stamped.12. Application: Tri-Pack, PA.13. Application: Hold Open, Tri-Pack, HO.14. Application: Door Saver Arm, DS.15. Application: Door Saver Hold Open Arm, DSHO.16. Finish: As specified in the Door Hardware Schedule.17. Finish, Painted: 689 - Aluminum.18. Finish, Painted: 695 - Duro Bronze.19. Finish, Painted: 696 - Gold.20. Finish, Plated: 605 - Polished Brass.21. Finish, Plated: 626 - Satin Chrome.22. Accessories/Options: Provide the following:

a. Parallel Arm Bracket, PA.b. Parallel Arm Hold Open Bracket, PAHO.c. Back Plate, BP.d. Top Jamb Drop Plate, DPTJ.e. Parallel Arm Drop Plate, DPPA.f. Narrow Frame Bracket, NFB.g. Full Plastic Cover, FC.

23. Warranty: Twenty-five years.

D. Architectural Style Commercial Door Control: American Eagle 5300 Series.1. ANSI/BHMA Certified: ANSI A156.4 Grade 1.2. UL/ULC Listed.3. UL 10C and UBC 7.2: Complies with positive pressure requirements.4. Handing: Non-handed.5. Manufactured in a WTO designated country therefore meets the requirements of the

BAA.6. Operation: Rack and pinion.7. Body: Heavy duty cast aluminum.8. Backcheck: Adjustable hydraulic backcheck; separate sweep, latch and backcheck

08 71 00-15



10. Mounting: Tri-pack for regular, top jamb and parallel arm installations; 12 inch (305 mm) by 3/4 inch (19 mm) mounting hole pattern; sex nuts and bolts.

11. Arm: Regular Arm, RA; flat, stamped.12. Application: Tri-Pack, PA.13. Application: Hold Open, Tri-Pack, HO.14. Application: Door Saver Arm, DS.15. Application: Door Saver Hold Open Arm, DSHO.16. Finish: As specified in the Door Hardware Schedule.17. Finish, Painted: 689 - Aluminum.18. Finish, Painted: 695 - Duro Bronze.19. Finish, Painted: 696 - Gold.20. Finish, Plated: 605 - Polished Brass.21. Finish, Plated: 625 - Polished Chrome.22. Accessories/Options: Provide the following:

a. Parallel Arm Bracket, PA.b. Parallel Arm Hold Open Bracket, PAHO.c. Back Plate, BP.d. Drop Plate, DP.e. Narrow Frame Bracket, NFB.f. Streamline Cover, SV.


E. Architectural Style Commercial Door Control: American Eagle 5500 Series.1. ANSI/BHMA Certified: ANSI A156.4 Grade 1.2. Certification: UL/ULC Listed.3. Certification: UL 10C and UBC 7.2: Complies with positive pressure requirements.4. Manufactured in a WTO designated country therefore meets the requirements of the

BAA.5. Handing: Non-handed.6. Operation: Rack and pinion.7. Body: Heavy duty cast aluminum.8. Backcheck: Adjustable hydraulic backcheck; separate sweep, latch and backcheck



10. Mounting: Tri-pack for regular, top jamb and parallel arm installations; 12 inch (305 mm) by 3/4 inch (19 mm) mounting hole pattern; sex nuts and bolts.

11. Arm: Regular Arm, RA; flat, stamped.12. Application: Tri-Pack, PA.13. Application: Hold Open, Tri-Pack, HO.14. Application: Door Saver Arm, DS.15. Application: Door Saver Hold Open Arm, DSHO.16. Finish: As specified in the Door Hardware Schedule.17. Finish, Painted: 689 - Aluminum.18. Finish, Painted: 695 - Duro Bronze.19. Finish, Painted: 696 - Gold.20. Finish, Plated: 605 - Polished Brass.21. Finish, Plated: 625 - Polished Chrome.22. Accessories/Options: Provide the following:

08 71 00-16

a. Parallel Arm Bracket, PA.b. Parallel Arm Hold Open Bracket, PAHO.c. Back Plate, BP.d. Top Jamb Drop Plate, DPTJ.e. Parallel Arm Drop Plate, DPPA.f. Narrow Frame Bracket, NFB.g. Full Plastic Cover, FC.


F. Heavy Duty Architectural Style Commercial Door Control: American Eagle 7100 Series.1. ANSI Conformance: ANSI A156.4 Grade 1.2. Certification: UL/ULC Listed.3. Certification: UL 10C and UBC 7.2: Complies with positive pressure requirements.4. Handing: Non-handed.5. Manufactured in a WTO designated country therefore meets the requirements of the

BAA.6. Operation: Rack and pinion.7. Body: Heavy duty cast iron.8. Backcheck: Adjustable separate hydraulic backcheck; backcheck positioning valve;

separate sweep, latch, backcheck intensity valve and backcheck positioning valves.9. Delayed Action: Adjustable; delayed action from maximum opening to 70 degrees.10. Adjustable Spring Size: 1 through 6; meets ANSI A117.1 and ADA requirements.

Designed to provide adjustable opening force, can meet Barrier Free Opening Force Requirements.

11. Mounting: Tri-pack for regular, top jamb and parallel arm installations; sex nuts and bolts.

12. Arm: Regular Arm, RA; Forged steel; flat.13. Application: Tri-Pack, PA.14. Application: Hold Open, Tri-Pack, HO.15. Application: Door Saver Arm, DS.16. Application: Door Saver Hold Open Arm, DSHO.17. Finish: As specified in the Door Hardware Schedule.18. Finish, Painted: 689 - Aluminum.19. Finish, Painted: 695 - Duro Bronze.20. Finish, Painted: 696 - Gold.21. Finish, Plated: 605 - Polished Brass.22. Finish, Plated: 625 - Polished Chrome.23. Accessories/Options: Provide the following:

a. Parallel Arm Bracket, PA.b. Back Plate, BP.c. Top Jamb Back Plate, BPTJ.d. Top Jamb Drop Plate, DPTJ.e. Parallel Arm Drop Plate, DPPA.f. Narrow Frame Bracket, NFB.g. Full Plastic Cover, FC.


2.13 EXIT DEVICES

A. Commercial Exit Device: American Eagle 4200 Series.1. Certification: UL/ULC Listed for Egress (Panic).2. Fire Label: UL/ULC Fire Labeled up to 1-1/2 hours for 3 ft by 7 ft maximum single or 6

ft by 7 ft maximum pairs.3. Certification: UL 10C and UBC 7.2: Complies with positive pressure requirements.4. Manufactured in a WTO designated country therefore meets the requirements of the

BAA.

08 71 00-17

5. Application: Rim.6. Application: Surface vertical rod with top and bottom Pullman latch bolts.

a. Latch Bolts: Deadlocking.7. Door Thickness: 1-3/4 inches (45 mm).8. Exit Device Size: A, for 39 inches to 48 inches dependent on device (991 to 1219 mm)

wide door.9. Exit Device Size: 3 ft unit standard (914 mm); 27 inches to 36 inches (686 to 914

mm) door dependant on device door width.10. Chassis: Cadmium plated steel with cover.11. Rail: Heavy gauge wrought steel.12. Rail: Stainless steel.13. Touch Pad: Heavy gauge wrought steel.14. Touch Pad: Stainless steel.15. Latch Bolt: Stainless steel dead locking.

a. Throw, Rim: 3/4 inch (19 mm).b. Throw, Surface Vertical Rod:5/8 inch (16 mm).

16. Projection: 2-5/8 inch (67 mm).17. Hand: Non-handed.18. Dogging: Hex key dogging.19. Dogging: None on fire labeled exit devices.20. Backset: 2-3/4 inch (70 mm).21. Stile Width: 4-1/4 inch (108 mm), minimum.22. Finish: As specified in the Door Hardware Schedule.23. Finish, Painted: 689 - Aluminum.24. Finish, Painted: 695 - Duro Bronze.25. Finish, Painted: 696 - Gold.26. Finish, Plated: 605 - Polished Brass.27. Finish, Plated: 626 - Satin Chrome.28. Finish, Plated: 630 - Satin Stainless Steel.29. Trim: Provide the following:

a. Blank Plate, 429 PTD.b. Pull Plate, 429 PUN.c. Pull Plate, 429 PUK.d. Narrow Escutcheon Trim, PHL Lever, 429 LPENX.e. Narrow Escutcheon Trim, PHL Lever, 429 LPEKF.f. Narrow Escutcheon Trim, PHL Lever, 429 LPEKX.g. Narrow Escutcheon Trim, PHL Lever, 429 LPENF.h. Heavy Duty Wide Escutcheon Trim, PHL Lever, 429 LPENXH.i. Heavy Duty Wide Escutcheon Trim, PHL Lever, 429 LPEKFH.j. Heavy Duty Wide Escutcheon Trim, PHL Lever, 429 LPEKXH.k. Heavy Duty Wide Escutcheon Trim, PHL Lever, 429 LPENFH.l. Keyed PHL Lever, Rose Trim, 429 LPS.m. Keyed PHL Lever, Rose Trim, 429 LPK.n. PHL Lever, Rose Trim, 429 LPN.o. Keyed Knob, Rose Trim, 429 CQK.p. Knob, Rose Trim, 429 CQN.q. Heavy Duty Keyed PHL Lever, Rose Trim, 429 LPSH.r. Heavy Duty Keyed PHL Lever, Rose Trim, 429 LPSH-IC.s. Heavy Duty Keyed PHL Lever, Rose Trim, 429 LPKH.t. Heavy Duty Keyed PHL Lever, Rose Trim, 429 LPKH-IC.u. Heavy Duty, PHL Lever, Rose Trim, 429 LPNH.v. Grip Pull, 429 GPH, _____ handed.w. Grip Pull, Keyed, 429 GPG, _____ handed.x. Grip Pull with Thumb Piece, Keyed, 429 GPK, _____ handed.y. Grip Pull/Thumb Piece, 429 GPN, _____ handed.

30. Accessories/Options: Provide the following:

08 71 00-18

a. Top Surface Vertical Rod, 1 ft (305 Mm) Extension for 8 ft (2438 fm) Door, 429021.

b. Top Surface Vertical Rod, 3 ft (914 Mm) Extension for up to 10 ft (3048 mm) Door, 429023.

c. Trim Back Plate, 2-1/2 inches (64 mm) by 8 inches (203 mm), 429014.d. Trim Back Plate, 3-1/2 inches (89 mm) by 8 inches (203 mm), 429017.e. Shim, End Cap, Glass Lite Shim 1/4 inch (6 mm), 429015 and Shim, Chassis,

Glass Lite Shim 1/4 inch (6 mm), 429016.f. Double Door Strike, 429019.


B. Architectural Commercial Exit Device: American Eagle 6200 Series.1. Certification: UL/ULC Listed for Egress (Panic).2. Fire Label: UL/ULC Fire Labeled up to 3 hours for 4 ft by 8 ft (1219 mm by 2438 mm)

maximum single or 8 ft by 8 ft (2438 mm by 2438 mm) maximum pairs.3. Certified: ANSI/BHMA Grade 1 A156.3-2001.4. Certification: UL 10C and UBC 7.2: Complies with positive pressure requirements.5. Manufactured in a WTO Designated country therefore meets the requirements of the

BAA.6. Application: Rim.7. Application: Surface vertical rod with top and bottom Pullman latch bolts.8. Application: LBR Surface vertical rod with top Pullman latch bolt and bottom auxiliary

latch bolt for fire labeled openings.9. Door Thickness: 1-3/4 inches (45 mm).10. Exit Device Size: A, for 33 inches to 48 inches dependant on device (838 to 1219 mm)

wide door.11. Exit Device Size: 3 ft unit standard (914 mm); 27 inches to 36 inches (686 to 914

mm) door dependant on device door width.12. Chassis: Cadmium plated steel with cover.13. Rail: Extruded aluminum.14. Touch Pad: Stainless steel.15. Latch Bolt: Stainless steel dead locking.

a. Throw, Rim: 3/4 inch (19 mm).b. Throw, Surface Vertical Rod: 5/8 inch (16 mm).

16. Strike: Low profile strike.17. Projection: 3-1/8 inch (79 mm); 1-5/8 inch (41 mm), dogged.18. Hand: Non-handed.19. Dogging: Hex key dogging (non-labeled doors).20. Dogging: Cylinder dogging (non-labeled doors).21. Dogging: None on fire labeled exit devices.22. Backset: Determined from face of strike.23. Stile Width: 4-1/4 inch (108 mm), minimum.24. Finish: As specified in the Door Hardware Schedule.25. Finish, Plated: 605 - Polished Brass.26. Finish, Plated: 606 - Satin Brass.27. Finish, Plated: 613 - Oil Rubbed Bronze.28. Finish, Plated: 626 - Satin Chrome.29. Finish, Plated: 630 - Satin Stainless Steel.30. Trim: Provide the following:

a. Heavy Duty Wide Escutcheon Trim, PHL Lever, 629 LPENXH.b. Heavy Duty Wide Escutcheon Trim, PHL Lever, 629 LPEKFH.c. Heavy Duty Wide Escutcheon Trim, PHL Lever, 629 LPEKXH.d. Heavy Duty Wide Escutcheon Trim, PHL Lever, 629 LPENFH.e. Heavy Duty Keyed PHL Lever, Rose Trim, 629 LPSH.f. Heavy Duty Keyed PHL Lever, Rose Trim, 629 LPSH-IC.g. Heavy Duty Keyed PHL Lever, Rose Trim, 629 LPKH.

08 71 00-19

h. Heavy Duty Keyed PHL Lever, Rose Trim, 629 LPKH-IC.i. Heavy Duty, PHL Lever, Rose Trim, 629 LPNH.j. Heavy Duty Keyed BSN Lever, Rose Trim, 629 LBSH.k. Heavy Duty Keyed BSN Lever, Rose Trim, 629 LBSH-IC.l. Heavy Duty Keyed BSN Lever, Rose Trim, 629 LBKH.m. Heavy Duty Keyed BSN Lever, Rose Trim, 629 LBKH-IC.n. Heavy Duty, BSN Lever, Rose Trim, 629 LBNH.o. Heavy Duty Keyed BSN Lever, Rose Trim, 629 LMSH.p. Heavy Duty Keyed BSN Lever, Rose Trim, 629 LMSH-IC.q. Heavy Duty Keyed BSN Lever, Rose Trim, 629 LMKH.r. Heavy Duty Keyed BSN Lever, Rose Trim, 629 LMKH-IC.s. Heavy Duty, BSN Lever, Rose Trim, 629 LMNH.t. Heavy Duty, Keyed Thumb Latch Pull, 629 GPK.u. Heavy Duty, Keyed Pull, 629 GPG.v. Heavy Duty, Push Plate, 629 PTD.w. Heavy Duty, Hospital Pull, 629 PUN.x. Heavy Duty, Keyed Hospital Pull, 629 PUK.

31. Accessories/Options: Provide the following:a. Top Surface Vertical Rod, 2 ft (914 Mm) Extension for up to 10 ft (3048 mm)

Door, 429023.b. Shim, End Cap, Glass Lite Shim 1/4 inch (6 mm), 429015 and Shim, Chassis,

Glass Lite Shim 1/4 inch (6 mm), 429016.c. Double Door Strike, 429019.

32. Warranty: Ten years.33. Exit Device Electrical Options.

a. Alarm (AL).b. Electric Dogging (ED).c. Electrical Latch Retraction (EL).d. Signal Switch (SS).e. Power Supply ED.f. Power Supply EL.g. Key Switch with Lights Maintained.h. Key Switch with Lights Momentary.i. Key Switch Narrow Maintained.j. Key Switch Narrow Momentary.k. Push Button Maintained.l. Push Button Momentary.m. Push Button Narrow Maintained.n. Push Button Narrow Momentary.o. Push Button Mushroom Maintained.p. Push Button Mushroom Momentary.q. Push Button Narrow Maintained.r. Push Button Narrow Momentary.s. Digital Interior Key Pad.t. Digital Exterior Key Pad.u. Electric Hinge 4.5 - 26D.v. Electric Hinge 4.5 - 10B.w. Electric Hinge 4.5 - US4.x. Electric Hinge 4.5 - US3.y. Electric Hinge 4.5 - 32D.

PART 3 EXECUTION

3.1 EXAMINATION

A. Do not begin installation until substrates have been properly prepared.

08 71 00-20

B. If substrate preparation is the responsibility of another installer, notify Architect of unsatisfactory preparation before proceeding.

3.2 PREPARATION

A. Clean surfaces thoroughly prior to installation.

B. Prepare surfaces using the methods recommended by the manufacturer for achieving the best result for the substrate under the project conditions.

3.3 INSTALLATION

A. Install in accordance with manufacturer's instructions. Test for proper operation and adjust until satisfactory results are obtained. Replace hardware if proper operation is not achieved.

3.4 PROTECTION

A. Protect installed products until completion of project.

B. Touch-up, repair or replace damaged products before Substantial Completion.

END OF SECTION

08 71 00-21