vme_guide.pdf

8/14/2019 vme_guide.pdf

1/30

VME Data Acquisition System:Fundamentals and Beyond

Abhinav Kumar

Bhabha Atomic Research Centre, Mumbai

March 2011


2/30

Chapter 1--------------------------------Introduction to VME

Chapter 2--------------------------------VME Architecture

Chapter 3--------------------------------Data Acquisition Setup under VME

Chapter 4

--------------------------------Data Acquisition with VME Modules using LAMPS

Presentation Outline


3/30

Introduction to VME

VME stands for VERSA-Module Euro card

introduced in 1981 for industrial, commercial and

military applications.

Electrical and mechanical specifications are definedby the standard.

VME bus is a master-slave computer architecture.

The signaling scheme is asynchronous, meaning that

the transfer is not tied to the timing of a bus clock.

VITA (VME International Trade Association) is the

organisation whose purpose is to promote and

develop the VME


4/30


5/30

VME Crate

smart fan units

VMEmaster VME slavepower supply

backplane

VME Components

Optical Link


6/30


7/30

As the VME is an asynchronous bus, the bandwidth indicated is atheoretical limit. For VME64, It works to around 80 MB/s ofTheoretical maximum bandwidth ; usually the actual transfer rate isless than 50% of the bandwidth

High Readout Speeds

High Density Modules can provide up to 640 Channels (1 controller+ 20 Digitizers) in a single VME crate with 21 slots.

Usage of high bandwidth optical interconnect link makes sure thatthe interconnect technology doesnt become a bottleneck whiletransferring data.

Advantages of VME over CAMAC Standard


8/30

Chapter 2--------------------------------

VME Architecture and

Protocols

/DS0, /DS1

/DTACK

DATA

ADDRESS

/AS


9/30

MASTER

LWO

RD*

D[31

..0]

BER

R*

DTACK*

WRITE*

DS

0*

DS

1*

AS

*

AM[5..0]

IAC

K*

BCLR*

SYS

RESET*

ACFAIL*

SLAVE

BACKPLANE INTERFACE LOGIC

LWO

RD*

A[31

..1]

D[31

..0]

BER

R*

DTA

CK*

WRITE*

DS

0*

DS

1*

AS

*

AM[5..0]

IAC

K*

SYSRESET*

DATA TRANSFER BUS (DTB)

DTB ARBITRATION BUS

PRIORITY INTERRUPT BUS

UTILITY BUS

IRQ[7..1]*

IRQ[7..1]*

A[31

..1]

BBSY*

BG[3..0]IN*

BR[3

..0]*

SYSCLK

BG[3..0

]OUT*

VME Architecture

Electrical Properties

All lines use TTL levels ; Low = 0 .. 0.6 V; High = 2.4 .. 5 V

Address, Address Modifier and data lines are active high; Protocol

lines are active low.

* Active low signals


10/30

Addressing modes - A16, A24, A32, A40, A64

The addressing mode and the access type are defined by the Address

Modifier bus AM[5:0]

AM Code Functions

0x3B A24 block transfer

0x39 A24 single cycle

0x2F CR/CSR space access


0x20 2eVME and 2eSST transfers (+ extended AM)

0x0B A32 block transfer (BLT)


0x08 A32 64-bit block transfer (MBLT)

VME Addressing Modes


11/30

Address=BaseAddress + Offset

The maximum VME address space is made of 264 bytes (although in most

cases only 232 are used, since the A64 mode is very infrequent)

Each slave occupies a portion of this space, depending on its internal

addressing capability

There are 3 ways to allocate the address space of the slaves:

1. by the Base Address of the slaves which is set at hardware level by

means of jumpers or rotary switches

2. by the position of the slave in the crate (Geographical Address)

3. by the content of some registers of the slave programmed by the software(Address Relocation)

modes 2 and 3 are available in the VME64x only

VME Address Space


12/30

Data readout is possible in following modes -

Single cycle

Reads a word from the slave FIFO

BLT/MBLT (Block Transfer/Multiplexed Block Transfer)

Reads a number of events limited to 256 words from any slave module

In MBLT two 32 bit words are multiplexed to read as a single 64-bit word in

VME64 standard

CBLT (Chained Block Transfer)

Most pertinent mode for nuclear physics applications allowing for event-

by-event data acquisition.

Reads the data belonging to the same physical event from several

contiguous boards in a crate limited to 256 words per CBLT cycle

VME Data Readout


13/30

The Chained Block Transfer has been introduced for sparse

data readout across multiple modules.

It consists in reading the data belonging to the same physical

event from several contiguous boards in a crate.

It uses the IACKIN-IACKOUT daisy chain line already

present in any VME backplane to propagate the readout

token.

No additional hardware nor external connections are

required.

The CBLT is handled by the slaves and is transparent to the

master

The use of the Bus Error to terminate the cycle is mandatory.

Chained Block Transfer


14/30

The Multi Cast Write (MCST) is a single write cycle that involves several

slaves in the crate.

The MCST uses the same propagation mechanism as the CBLT

The master initiates the cycle like a normal single write The slaves get the data in sequence and the last one asserts the DTACK

Multi Cast Write

Many VME acquisition boards use FIFO memories to store the data.

This is particularly suitable for physics applications in which the events occur

randomly in time and are readout sequentially

A read access to any address within that range causes the non repeatable

extraction of one word from the FIFO.

CAEN ADC modules are endowed with 32 Events Buffer.

FIFO Memories


15/30

The VME features a 7 level prioritized interrupt architecture; the request

lines IRQ[7:1] are shared between all the slots

The interrupt is initiated by the interrupter(this can be any board in any

slot) that asserts one IRQ.

The interrupt handlers (usually the board in slot 1) monitor the IRQ

lines and generate an interrupt acknowledge cycle in response to the

request

The interrupt handler reads the STATUS/ID of the interrupter from the

data bus

If more interrupters had asserted the same IRQ line, the IACKIN-

IACKOUT daisy chain allows the uppermost left to respond first (priority

given by the position)

Interrupts in VME


16/30

Chapter 3--------------------------------

Setting up a VME acquisition

system

C.A .E .N .


17/30

It makes possible to control the VME bus remotely from a standardPC through a high speed link

The acquisition program (DAQ) runs on the remote PC

The VME board is just hardware (no software runs on it)

Computing power (processors, memories, disks, etc) is on the PC

Unlike the ethernet port of a SBC, the communication link of the bus

adapter must be able to sustain high data transfer rates

VME-PCI/PCIe: usually communicates through an optical link,requires a card inside the PC

Bus Adapter Feature


18/30

HW and SW upgrade on PC side: you can buy a new one at any time

Easy getting started: just install a driver in the PC

Ready at power-up (no boot required)

Lower total cost of ownership Multi-crate interconnection and control

used for datatransfer

C . A . E . N .

Bus Adapter Slaves

USBOptical Link

computingpower ishere!

this is justhardware

access to thebus throughthe adapter

Advantages of Bus Adapter over SBC


19/30

Max throughput rate: 70MB/s

VME64/VME64X (no 2eSST)

PCI 32bit, 33MHz

Optical Link: 1.25 Gb/s Max distance: 300m

FPGA

RAM

buffer

Optical

Link

VMEbus

FPGAOptical

Link

RAM

buffer

PCI bus

A2818

V2718

PCI-int

CONET

~ 70 MB/s

max 300m

VME Controller V2718


20/30

BASE ADDRESS:

which board inside

the crate

OFFSET:

which register inside

the board

A32 mode

A24 mode

C 2 4 8

31 24 23 16 15 0

OFFSET

0 1

4

23

5

8

679

C

AB

DE

F 0 1

4

23

5

8

679

C

AB

DE

F 0 1

4

23

5

8

679

C

AB

DE

F 0 1

4

23

5

8

679

C

AB

DE

F

unused 4 8

31 24 23 16 15 0

OFFSET

0 1

4

23

5

8

679

C

AB

DE

F 0 1

4

23

5

8

679

C

AB

DE

F

Address Space: 16 Kbytesfrom 0xC2480000 to 0xC248FFFF

Address Space: 16 Kbytes

from 0x480000 to 0x48FFFF

VME Base Address ( Hardware Setting)


21/30

Operational Aspects

Controller should beinserted in slot 1 of the

VME Crate.

While setting up the

CBLT Chain, the

modules forming thechain should be

contiguous; last module

should be terminated

with a 50 Ohm

resistance.

Scalars can be inserted

in any empty slot.

MesyTec ADCs, if used

along with CAENModules, should be

inserted first in the

chain.


22/30

Chapter 4--------------------------------

Data Acquisition using VME

Modules through LAMPS software


23/30


24/30

Software Installation

Installation of A2818 (PCI CONET Controller) driver

- CAEN A2818 PCI CARD

- Linux kernel Rel. 2.4 or 2.6 with gnu C/C++ compiler

Installation of CAENVMELib Library

Set of functions for the control and the use of CAEN VME

Bridges. Typically, it provides function calls to

Open (Init) and Close the communication and the devices Make single Read/Write cycles

Make Block Transfer Read/Write cycles

Wait for an interrupt and make a IACK cycle

Installation of LAMPS

No changes in the LAMPS installation procedure.

PCICONET

Controller

PCI Slot


25/30

Checking for Basic Connectivity

Post hardware setup and software installation, basic connectivity with the Bus

Adapter can be checked using the Test Feature of the LAMPS software.

Indication of an error at this stage implies an incorrect hardware/software setup.


26/30

Setup Configuration under LAMPS

Bus Adapter needs no Base Address configuration. For other modules, setting

up of Base Address in software is compulsory.


27/30

Setting up Special Properties

Configuring SCALERS

under LAMPS

TDC special settings

QDC special

settings


28/30

Blue Rectangular region VME Controller ; Green Rectangular Region- CBLT

Chain ; Purple rectangular region - Scaler


29/30

Master Gate Blocking

Master Gate blocking is essential to have any meaningful acquisition with VME, failing

which a good number of events could be corrupt depending on the data rate.

Concept:

No master gate should reach VME modules until the current event has been completelydigitized and read out. This statement may look incomplete because it doesnt talk of the

32-event buffer in VME modules. But the solution (see below) is based on BUSY status of

VME modules, hence it covers this complication.

Solution:

Chain the BUSY output from all the modules in use using short Lemo cables and Lemo Tconnectors and veto the master gate of the experiment with this before input to VME

modules.

LAMPS automatically displays the dead time when the blocked and unblocked master

gates are provided on two inputs of CAEN V830 VME scaler module.


30/30

Conclusion

The VME DAQ in the current form provides us with a powerful system

because of the large number of parameters which can be acquired

simultaneously and high event rates.

The zero suppressed readout option along with the availability of variety of

digitizers with higher channel density presents a very good system in front of

users, before we eventually migrate to digital DAQ.

vme_guide.pdf

Documents