volume iii price bid/boq - engineering projectsusing hydraulic piling rig with power unit and...

AN ISO 9001 & 14001 COMPANY

TENDER DOCUMENT

TENDER No: DLI/CON/697/589

FOR

Construction of Mess Block, Girls Kitchen and Dining Hall at IIIT Campus, RGUKT, Basar, Adilabad Dist. Telangana.

VOLUME – III

PRICE BID/BOQ

NIT NO.:

1 2 3

In Figures In words In Figures In words

1

Construction of Mess Block-Girls Kitchen and Dining

Hall at IIIT Campus, RGUKT,Basar, Adilabad Dist.,

Telangana

99,672,827.0

99,672,827.0

Seal & Signature of Tenderer

NIT No.DLI/CON/697/589 dated 09.10.2017.

Note:

Rates to be quoted in this tender are inclusive of all taxes and duties etc. excluding GST (GST as per applicable shall be released on submission of documentary evidence of

payment made towards GST).

BIDDERS FINANCIAL OFFER:

(In Figures)___________________________________________________________________________________________________________In Figures__________

(In Words)___________________________________________________________________________________________________________In Figures__________

S.NO.Name of the Work

Estimated Cost

Put to Tender

BIDDER'S PRICE

% ABOVE / BELOW / AT PAR

4 5=(4 x 3)

AMOUNT IN Rs. AFTER ADDING % (-) BELOW AT

PAR/(+) ABOVE.

ENGINEERING PROJECTS (INDIA) LTD.(A GOVERNMENT OF INDIA ENTERPRISE)

Name of the work:Construction of Mess Block-Girls Kitchen and Dining Hall at IIIT Campus, RGUKT, Basar, Adilabad Dist.,

Telangana.

QUOTING SHEET FOR BIDDER

EPIL CONTRACTOR

Sl. No Description of Work

UOM Quantity Rate(Rs)

Amount (Rs.)

1 Bored cast-in-situ M 25 grade Design mix RCC pile 600mm diausing hydraulic piling rig with power unit and complete

accessories including shifting rig from from one bore location

to another ; hire and running charges of Bentonite pump , light

crane for lowering reinforcement cage ; loader 1 cum bucket

capacity ; tipper 5.50 cum capacity for disposal of muck from

pile bore hole to a distance of 1 KM ; cost of Bentonite solution

and temporary casing of appropriate length for setting and

removal of the same ; including filling the bore with M 25

Design Mix ( mixing concrete in Mechanical Weigh Batching

units up to 15 cum/hr capacity ) using 20mm size (SS5) hard

granite machine crushed graded metal (Coarse aggregate)

from approved quarry, using a minimum quantity of 380 kgs.

of cement per 1 cum of concrete including cost and

conveyance of all materials like cement, fine aggregate

(Sand), coarse aggregate, water etc., to site and cost of

seigniorage charges on all materials ,laying concrete, curing ,all

incidental charges : labour charges etc. complete but

excluding cost of reinforcement and fabrication charges as

per drawing and technical specifications as per IS - 2911 ( Part-

I Section II ) -1979 for finished item of work. ( Length of Pile

for payment shall be measured up to bottom of Pile cap )

RMT 12.00 4640.27 55683.24

2

Filling with Sand, including supply and delivery of goodgravel for filling, including cost of gravel, seinourage charges

and conveyance to site, filling charges, watering, tamping and

rammming and all labour charges and operational charges

complete as directed by the Departmental officers.

Cum 150.00 1140.96 171144.00

3

Clearing and grubbing of land including uprooting wildvegetation, grass, bushes, shrubs, saplings and trees of girth

upto 300mm, removal of stumps of such trees cut and disposal

of unserviceable materials and stacking of serviceable material

to be used or auctioned, upto a lead of 1000m including

removal and disposal of top organic soil not exceeding 150mm

in thickness as per technical specification Clause 201

MORD/MORTH

Sqm 5000.00 6.24 31200.00

4

Supply and placing of the Ready Mix (RMC) Design MixConcrete grade M20 as per IS 4926-2003 with minimum

cement content as per IS code 456-2000 using 20 mm graded

metal, from standard suppliers approved by the department

including pumping, laying concrete, vibrating, curing

,centring,shuttering etc. complete but excluding cots of steel

and its fabrication charges, for finished item of work.-Plinth

Beam

Cum 197.45 9481.47 1872096.39

5

Earth work excavation for foundations and depositing on bankfor all lifts with an initial lead of 10m including all operational

,incidental, labour charges such as shoring, sheeting ,planking

,strutting etc complete for finished item. Including seignorage

excluding dewatering charges etc.

Cum 1385.00 147.59 204412.15

6

Filling with Excavated Earth (Ordinary Soil) including cost andconveyance of all labour charges etc., complete for finished

item of work.Cum 1824.99 217.28 396533.83

BILL OF QUANTITIES

Name of the work:Construction of Mess Block-Girls Kitchen and Dining Hall at IIIT Campus, RGUKT, Basar Dist., Telangana

Page 1 of 11

7

Filling with Gravel, including supply and delivery of goodgravel for filling, including cost of gravel, seinourage charges

and conveyance to site, filling charges, watering, tamping and

rammming and all labour charges and operational charges

complete as directed by the Departmental officers.

Cum 785.98 480.53 377686.97

8

Removal of unsuitable / Unserviceable soil includingexcavation, loading and disposal upto 5000 m lead but

excluding compaction ground supporting embankment

subgrade replacement by suitable soil, which shall be paid

separately as per Clause 303.5.2 as per Technical Specification

Clause 302.3.11 MORD / 301 MORTH

Cum 150.00 84.00 12600.00

9

Dismantling of existing structures like culverts, bridges,retaining walls and other structure comprising of masonry,

cement concrete, wood work, steel work, including T&P and

scaffolding wherever necessary, sorting the dismantled

material, disposal of unserviceable material and stacking the

serviceable material with all lifts and lead of 1000 m as per

Technical Specification Clause 202 MORD / MORTH

Cum 25.00 1209.77 30244.25

10

Construction of RR Masonary in C.M (1:6) prop. Using hardgranite stone including cost and conveyance of all materials

like cement, sand, water, Granite stone etc. including cost of

seigniorage charges on all materials, all taxes including labour

for cutting stones to required size and shape, mixing of cement

mortar construction, Scaffolding charges etc. complete for

finished item of work.

Cum 43.00 4566.03 196339.29

11

Providing Antitermite treatment as per IS 6315 (Part - 2) 2001(Pre-constructional chemical treatment measures) along the

internal & external vertical faces of the columns, plinth beams,

basement and top surface of the basement filling below

flooring bed as per the specified procedure conforming to IS

6315 (Part-2) 2001 and other relevant approved specification

duly using Chlorpyriphos/ Lindane emulsifiable concentrate

20% with 1% concentration @ 7.5 Liters/ sqm of the vertical

surface & @ 5.0 Liters/ sqm of the horizontal surface of the

substructure to a depth of 500 mm around columns & 300 mm

deep around plinth beams, basements & floor filling area

including excavation channel along the wall & rodding etc &

cost & conveyance of all materials to the site, cost of labour for

spraying, rodding etc complete for finished item of work as per

the approval of the Engineer-in-Charge

Sqm 5088.00 303.42 1543800.96

12

Plain Cement concrete in (1:4:8) prop. Using 40 mm HBG metalincluding cost and conveyance of materials to site including

seignorage fee, Machine mixing, concrete laying tamping,

vibrating, watering curing and all labour charges, hire and

operational charges of machinery, water lead charges and

including bailing of water.etc. complete for finished item of

work.

Cum 545.00 4116.93 2243726.85

13




including pumping, laying concrete, vibrating, curing etc.

complete but excluding cots of steel and its fabrication

charges, centering, shuttering for finished item of work.

Pile cap Cum 800.00 7668.74 6134992.00

a Beams

1.Ground Floor: Cum 410.00 10045.29 4118568.90

Page 2 of 11

2.Terrace Floor: Cum 4.00 10249.04 40996.16

b Grade slab/ Plinth Protection slab (100mm thickness) Sqm 4830.00 641.64 3099121.20

c Slab :(150 mm Thick) (1 Sqm)

1.Ground Floor: Sqm 100.00 1357.45 135745.00

2.Terrace Floor: Sqm 40.00 1381.19 55247.60

d Slab :(175 mm Thick) (1 Sqm) Sqm 4686.81 1518.74 7118045.82

e Side wall of water tank (200mm Thickness) Sqm

1.Ground Floor: Sqm 200.00 4087.53 817506.00


f Stair Case Cum 2.85 10045.29 28629.08

14




including pumping, laying concrete, vibrating, curing etc.

complete but excluding cots of steel and its fabrication

charges, centering, shuttering for finished item of work.

a Columns :

1.Ground Floor: Cum 180.00 9064.43 1631597.40


b Lintels :

1.Ground Floor: Cum 11.00 9340.51 102745.61


c Chajja/Sunshade: 100mm thick

1.Ground Floor: Sqm 200.00 1087.13 217426.00


d Loft: 50mm thick Sqm 50.00 762.27 38113.50

e Precast slabs:40mm thick Sqm 160.00 702.75 112440.00

15

FLYASH Brick masonry 29x22.5x14 cm for panel walls insuperstructure with CM (1:6) prop: (Cement : Screened sand)

from approved source having minimum crushing strength of

50 Kg/Sqcm. including cost and conveyance of all materials

like cement, screened sand, bricks, water etc., to site, including

sales & other taxes on all materials and such as labour charges,

like mixing cement mortar, scaffolding charges, constructing

masonry, lift charges, curing, etc.,and overheads & contractors

profit complete for finished item of work. (APSS No. 501 &

504).

a.Ground Floor: Cum 550.00 5809.27 3195098.50

b.Terrace Floor: Cum 80.00 6130.61 490448.80

16

FLYASH Brick Masonry 29x10x14cm for partition walls (10.0cm thick) in CM (1:6) prop. (Cement : Screened sand) from

approved source having minimum crushing strength of 50

Kg/Sq.cm and placing 2 Nos. of 6mm M.S plain rods in every

third layer with free ends of the reinforcement pegged into

mortar joints of main brick walls where applicable including

cost and conveyance of all materials like cement, steel, sand,

bricks, water etc., to site, including sales & other taxes on all

materials, all operational, incidental charges such as labour

charges for mixing cement mortar, scaffolding charges,

constructing masonry, lift charges, curing, etc., and overheads

& contractors profit but excluding cost of steel and its

fabrication charges complete for finished item of work. (APSS

No. of 501 & 509)

Ten Sqm 223.60 6637.68 1484185.25

Page 3 of 11

17

Providing & fixing of Rabbit wire mesh & nominalreinforcement such as nails etc., as directed by Engineer-in-

charge with dubara sponge finishing, including cost &

conveyance of all materials to site, seigniorage charges, sales &

other taxes on all materials, operational & incidental, cost and

conveyance of cement, wire mesh, water to work site,

centering, scaffolding and form work, lift charges etc.,

complete for finished items of work , for finished item of work.

(APSS No.403 & 903)-25mm thick

Sqm 1000.00 460.82 460820.00

18

20mm thick plastering to masonry walls to external side with16mm in C.M(1:6)prop.as Ist coat and 4mm in C.M(1:4)prop.

as II nd coat with dubara sponge finishing and curing etc.,

seignourage and all operational incidental labour charges such

as scaffolding mixing mortar,curing etc.complete as per

specification and drawings for finished item of work.

a.Ground Floor: Sqm 2421.40 333.37 807222.12

b.Terrace Floor: Sqm 432.00 368.52 159200.64

19

Plastering 12mm thick inside in two coats with a base coat of8mm thick in CM(1:5) prop and top coat of 4mm thick in CM

(1:3) prop. with dubara sponge finish including cost and

conveyance of all materials and water to work site seigniorage

and all operational incidental, labour charges such as

scaffolding, mixing mortar lift charges curing etc., complete

for finished item of work.



20

plastering 12mm thick in two coats, first with 8mm thick incement mortar (1:5) prop and second with 4mm thick in

cement mortar (1:3) prop including cost and conveyance of all

materials to site seignorage fee , Screening and mixing, laying

finishing with sponge finish and watering, curing including all

labour charges ,hire and operational charges,scaffolding etc.,

complete for finished item of work. (for Ceiling)



21

Damp proof course 50mm thick with 1:2:4 cement concreteNominal mix, using 12mm hard broken stone aggregate

including cost of all materials, seigniorage charges, excluding

conveyance charges of materials including the cost of

machinery, labour charges, mixing, placing in position,

leveling, vibrating, curing etc. complete for finished item of

work. (I.P.S. Flooring)

Sqm 500.00 340.85 170425.00

22

Plain Cement concrete in (1:5:10) prop. Using 40 mm HBGmetal including cost and conveyance of materials to site

including seignorage fee, Machine mixing, concrete laying

tamping, vibrating, CENTRING,watering curing and all labour

charges, hire and operational charges of machinery, water lead

charges and including bailing of water.etc. complete for

finished item of work. For DUMMY COLUMNS

Cum 150.00 6569.01 985351.50

23

Plain Cement concrete in (1:2.5:5) prop. Using 20 to 12 mmHBG metal including cost and conveyance of materials to site

including seignorage fee, Machine mixing, concrete laying

tamping, vibrating, watering curing and all labour charges, hire

and operational charges of machinery, water lead charges and

including bailing of water.etc. complete for finished item of

work. For Terrace slab and corners of papapet walls.

Cum 5.00 5771.39 28856.95

Page 4 of 11

24

Painting to walls with 2 coats (all colours of acrylic exterioremulsion paint or other equal and approved water proof

cement paint all to give an even shade after thourughly

brushing the surface to remove all dirt and remains of loose

powdered materials, complete for finished item of work as per

SS 912 for external walls. for all floors

Sqm 2853.40 177.12 505394.21

25

Providing and applying Wall Putty to use surface (white / offwhite) - of average 1.5 to 2 mm thickness over plastered

surface to prepare the surface even and smooth after

thoroughly brushing the surface to remove all dirt and

remains of loose powdered materials, applying emery paper,

Sand the surface, clean & wipe off loose dust, applying knifing

paste filler by putty knife / muslin pad, air dry for 2 - 3 hrs,

sand with 180 and 320 No., emery paper for the surface

preparation and applying two coats of Interior Acrylic

emulsion over primer over putty including cost,scaffolding and

conveyance of all materials to work site and all operational,

incidental, labour charges, over heads and contractors profit

etc., complete for finished item of work in all floors for Internal

walls

Sqm 3752.98 307.08 1152465.10

26

White washing two coats with whiting of approved quality togive an even shade after thoroughly brushing the surface to

remove all dirt and remains of loose powdered materials

including cost and conveyance of all materials, labour charges

and incidental such as scaffolding, lift charges etc., complete

for finished item of work (to ceilling)

Sqm 3408.44 30.83 105082.21

27

Providing impervious coat to exposed RCC roof slab surfacewith CM(1:3), 20mm thick with 1kg of water proof compound

per bag of cement laid over roof when it is green including

cost of all materials, seigniorage charges, excluding

conveyance charges of materials and including all operational,

incidental and labour charges for mixing mortar, laying,

rendering smooth and thread lining, curing, rounding off

junctions of wall and slab etc,, complete for finished item of

work



28

Supplying and fixing of Unplasticised Poly Vinyl Chloride(UPVC) 3 track sliding windows with mesh shutter – (2-glass

shutters and 1-mesh shutter) duly manufactured using UPVC

reinforced profiles (Composition of profile shall consists a

minimum of 5.5 PHR of TiO2 and not more than 12 PHR of

CaCo3 for every 100 parts of PVC resin) of (94 mm x 45

mm)/(80 mm x 52 mm) x 2.20 mm for outer frames, (58 mm x

39 mm)/(54 mm x 38 mm) x 2.20mm for sliding shutter

frames capable of mounting single glazing system structurally

reinforced with hot dip galvanized up to 50 microns of

minimum thickness of 1.0/1.2 mm prefabricated & welded

through fusion welding. The window sash shall be fitted with 5

mm thick clear float glass of reputed make and mesh shutter

frame shall be (42 mm x 25mm)/(52 mm x 21.5 mm) x 2.0 mm

fitted with Vinyl Coated Fiber mesh- on rollers/ pulley duly

fixed with Grey colour TPV Gasket for sash & Glazing bead

shall be co-extruded with Grey colour soft PVC. System shall

have single point locking with Touch Lock and the system is to

be installed at the site using anchor fasteners, silicon rubber

sealant, easy glazing/ deglazing at site etc., including cost and

conveyance of all materials, accessories, labour charges for

transportation, erection at site complete for finished item of W1 Sqm 330.40 8340.48 2755694.59

Page 5 of 11

29

Providing, supplying & fixing of Fixed Louvered Ventilatormade out of multi chambered uPVC sections with Glazing bead

shall be co-extruded with Grey colour soft PVC. having isolated

drainage and reinforced with Galvanized Iron profiles

throughout the window. The outer frame having an overall

size of 60 mm x 55 mm x 2.40 with reinforcement of 1 mm

thickness and Mullion with overall size of 74 mm x 60 mm x

2.40 mm with reinforcement of 1 mm thickness. (Composition

of profile shall consists a minimum of 5.5 PHR of TiO2 and not

more than 12 PHR of CaCo3 for every 100 parts of PVC

resin).Ventilator shall be provided with 4.5 mm Pin Head glass,

standard hardware. Wall thickness of frame & Mullion shall be

2.4 mm.,including cost and conveyance of all materials,

accessories, labourcharges for transportation, erection at site

complete for finished item of work.

V1 Sqm 22.92 7505.41 172024.00

30

Flooring with Nano polished/Stain free soluble salt floortiles of size not less than 600mmx600mm x 8 mm

thickness regular finish and normal colours set over base

coat of CM (1:8) over already laid CC bed / RCC Roof Slab,

including neat cement slurry of honey like consistency spread

@ 3.3 kgs per sqm. & Jointed with neat cement to full depth

including cost of all materials like cement, sand, and water and

flooring stones etc., complete, including seigniorage charges,

labour charges for dressing of flooring stones etc., complete for

finished item of work, but excluding the cost of conveyance of

all materials.

Sqm 2995.00 1012.53 3032527.35

31

Flooring with high polished granite slabs 16 to 18mm thickother than black and regular colours set over base coat of

cement mortar (1:8), 20 mm thick over CC bed already laid or

RCC roof slab, including neat cement slurry of honey like

consistency spread @ 3.3.kgs per sqm & jointed neatly with

white cement paste mixed with pigment of matching shade to

full depth, including cost of all materials like cement, sand

water and tilesetc., complete, including seigniorage charges,

labour charges for dressing of tilesetc., complete for finished

item of work,

Sqm 100.00 4216.60 421660.00

32

Providing skirting to internal walls to 15 cm height/risersof steps with with Nano polished /stain free soluble salt

porcelain vitrified tiles screen printed of size 600 x600

mm and thickness between 8-10 mm 1st quality finish

colours special series set over base coat of CM (1:5) 12 mm

thick with cement slurry of honey like consistency spread at

the rate of 3.30 kgs per sqm and jointed with white cement

paste mixed with pigment of matching shade to full depth,

including cost of all materials like Shahabad stone, cement,

sand and water etc., complete including seigniorage charges,

etc., complete for finished item of work, but excluding the cost

of conveyance of all materials

Sqm 70.00 1021.68 71517.60

33

Flooring with polished shahabad stones 15 to 18 mm thick setover base coat of CM (1:8) over already laid CC bed / RCC Roof

Slab, including neat cement slurry of honey like consistency

spread @ 3.3 kgs per sqm. & Jointed with neat cement to full

depth including cost of all materials like cement, sand, and

water and flooring stones etc., complete, including seigniorage

charges, labour charges for dressing of flooring stones etc.,

complete for finished item of work

Sqm 500.00 523.43 261715.00

Page 6 of 11

34

Flooring with Edge cut Ceramic tiles 8-10mm thick-60x60cm1st quality of Non-skid red or white full body Ceramic floor

tiles of scratch free-stain free and scratch freenano finish,

set over base coat of cement mortar (1:8), 12 mm thick over

CC bed already laid or RCC roof slab, including neat cement

slurry of honey like consistency spread @ 3.3.kgs per sqm &

jointed neatly with white cement paste to full depth mixed

with pigment of matching shade, including cost and

conveyance of all materials like cement, sand water and tiles

etc., complete, including seigniorage charges, etc., complete for


Sqm 200.00 1108.77 221754.00

35

Flooring with Non-skid red or white full body Ceramicfloor tiles of size 300 x 300 mm and thickness

between 7-8 mm 1st quality conforming to IS:13711,

IS:13712, IS:13630 (Parts 1 to 15) of any colour and

finish in all shades and designs, set over base coat of cement

mortar (1:8), 12 mm thick over CC bed already laid or RCC roof

slab, including neat cement slurry of honey like consistency

spread @ 3.3.kgs per sqm & jointed neatly with white cement

paste to full depth mixed with pigment of matching shade,

including cost and conveyance of all materials like cement,

sand water and tiles etc., complete, including seigniorage

charges, etc., complete for finished item of work.

Sqm 417.00 891.89 371918.13

36

Providing and laying cinder concrete cinder mix (1; 15) prop.Using 12.5mm nominal size cinder laid in layers and

completed as directed for filling sunken floors including cost

and conveyance of all meterials, water to work site, complete

for finished item of work.

Cum 2.00 2424.83 4849.66

37Providing and fixing of 16 to 18 mm thk high polished granite urinal partitions- Black

Sqm 14.00 1787.73 25028.22

38

Dadooing to walls with Supply of glazed red or white fullbody ceramic wall tiles of size 300 x 450 mm / 320 mm x

400 mm and thickness 6 mm 1st quality conforming to

IS:13711, IS:13712, IS:13630 (Parts 1 to 15) of any colour and

finish in all shades and designs set over base coat of

C.M(1:3)prop. 12mm thick and neat grey cement slurryof

honey like consistency spread at the rate of 3.3Kg of cement

per sqm and jointed with neat white cement paste at 0.20 kg

per sqm mixed with pigment of matching shade to match the

shade of tiles including cost and conveyance of all materials

labour charges,water to work site,seigniorage and all

operational .incidental ,mixing mortor ,fixing in position ,lift

charges,curing, VAT etc., complete as per SS or as directed by

the departmental authorities for finished item of work.

Sqm 681.00 1045.22 711794.82

39

Supplying and fixing of stainless steel railing of grade SS 304 ofone meter height consisting of vertical posts 50 mm dia

embedbed in treads and landing of staircase, hand rail 50 mm

dia pipe with 2 Nos intermidiate 20 mm dia pipes parallel to

railing including fixing, welding to balusters as per design with

hand brushing, including cost and coveyance of materials

labour charges etc complete for finished item of work.

RMT 18.40 3677.32 67662.69

Page 7 of 11

40

Providing Thermo Mechanically Treated (TMT) (Fe 500grade as per IS 1786-1979) of different diameters for RCC

works , including labour charges for straightening, cutting,

bending to required sizes and shapes, placing in position with

cover blocks of approved materials and size and tying and lap-

splicing with binding wire of 18 SWG, forming grills for

reinforcement work as per approved designs and drawings,

including cost and conveyance of steel bars, including all

wastages such as overlaps, couplings, chairs, spacer bars

including cost and conveyance of binding wire, cover blocks

and all incidental, operational, labour charges such as cutting,

bending, placing in position, tying including sales and other

taxes on all materials etc. ,and overheads & contractors profit

complete for finished item of work.( APSS

No.126)Make:TATA,SAIL,VSP,JINDAL

a.Ground Floor: MT 600.00 59126.38 35475828.00

b.Terrace Floor: MT 5.00 60165.96 300829.80

41

Providing Mild Steel structural steel Angles, Channels & ISections of all sizes as per IS-1161, Labour charges for

fabricating all heavy steel works including cost of welding

rods, power charges, etc including cost of fixing in position, for

fixing heavy iron grills etc., erecting in position and fixing by

using chain pulley blocks, Derek pole arrangements and cranes

etc., complete in position

MT 5.00 80317.77 401588.85

42

Supplying & fixing collapsible steel shutters with vertical,double channel of 20 x10x2 mm of 100 mm centre ,Bracers

with flat iron 40x40x6 mm with 38 mm Diameter steel pulleys,

the top, bottom and side vertical frames of the collapsible gate

with 65x65mmx8mm MS Angle and middle guide rail at site

height with 65mmx8mm MS flat for the pulleys to guide and

fixed with necessary hold fasts, bolts, nuts, rivets, locking

arrangements, stoppers, handles, all approved steel primer

etc., complete for finished item of work as per special Spec

1105

Sqm 15.00 3555.01 53325.15

43

Providing Mild Steel structural steel pipesTrusses, stanchionsetc of all sizes as per IS-1161, Labour charges for fabricating all

heavy steel works like Trusses, Stanchions, Heavy Beams and

Girders including cost of welding rods, power charges, etc

including cost of fixing in position, for fixing heavy iron grills,

Trusses, Stanchions, Heavy Beams and Girders erecting in

position and fixing by using chain pulley blocks, Derek pole

arrangements and cranes etc., complete in position

MT 2.00 121028.38 242056.76

44

Supplying precast terrazzo chequered tiles conforming to IS:13801 using marble aggregates of size 10 mm , sand, marble

powder, white cement etc., with terrazzo topping not less than

6mm of tiles overall size not less than 20 mm thick of any

coloured shades set over base coat of cement mortar (1:6) 12

mm thick over CC bed already laid or RCC roof slab, including

near cement slurry of honey like consistency spread @ 3.3.kgs

per sqm & jointed with neat cement to full depth mixed with

pigment of matching shade including cost of all materials like

cement, sand water and tiles etc., complete, including

seigniorage charges, complete for finished item of work.

Sqm 400.00 730.38 292152.00

45 Extra cost for flooring Premium colours Sqm 500.00 555.58 277790.00

Page 8 of 11

46

Painting Red oxide with two coats with synthetic enamel paintof approved quality colour and grade-I having VOC (Volatile

Organic Compound ) content less than 50 grams/ liter.over a

primary coat to new welded surface including cost of primary

coat and cost and conveyance of all materials ,labourcharges

etc.as per SS and directed by the departmental authorities for


Sqm 150.00 132.68 19902.00

47

Providing specialized polysulphide sealant treatment to theexpansion joints (Size : 25mm x 12mm) duly a] Chipping and

removing of existing covering on expansion joints b] Cleaning

of the surface from dirt, dust and other contaminations c]

Application of one coat of - High performance specially

designed SBR latex polymer based bonding agent d] Providing

and application of Acrylic Polymer modified reinstatement

concrete /mortar to the damaged edges of joint and making

the groove. e] Providing and fixing of masking tape on top of

the joint both sides f] Providing and fixing of Back up support

material of Backer rod to leave the depth of 12mm on the joint

g] Providing and application of one coat of polysulphide

primer on inner edges of Joint. h] Providing and application of

Two part Polysulphide sealant to a width of 25mm and 12mm

depth with putty knife and neat finish i] Removing of masking

tape and providing and application of two coats of Acrylic

elastomeric cementitious coating

RMT 159.00 738.50 117421.50

48

Supply of expansion joint filler board conforming to IS: 1838for buildings, columns, beams and slabs 25 mm THICK Sqm 242.00 457.87 110804.54

49

Supply of expansion joint filler board conforming to IS: 1838for buildings, columns, beams and slabs 50 mm THICK Sqm 200.00 913.46 182692.00

50

Providing and fixing of 24 gauge alluminium sheet overexpansion joint groove of width 15cm fixed to walls / columns

at one edge and resting over the other block walls/columns

concealing expansion joint with slotted holes for free edge of

aluminium sheet to facilitate free movement of aluminium

sheet over the finished surface of expansion joint and wall face

using sheet metal screws with nylon receiver complete

including cost and conveyance of all materials to site, all

incidental, operational, labour charges , overheads &

contractors profit etc., complete for finished item of work as

per approved drawing (for all floors for vertical joints and

bottom of slab)

RMT 442.00 120.00 53040.00

Page 9 of 11

51

Supply and fixing doors as per drawings with Medium teakwood frame of section 150mmx150mm and Flush door

shutters, solid bond wood block board type with teak veneer

on one face and commercial ply on another

face(lipping):35mm thick conforming to IS:2202 including cost

and conveyance to site of teak wood frame, flush shutter

including supply and full size 12mm toughend glass, MS Z hold

fasts of size 300mmx40mmx5mm- 6 No's ,Alluminium Hinges

of size 150mm long- 6 No's, Alluminium Aldrop of size 300mm

as per IS:2681- 1 No, Alluminium 200mmx10mm size tower

bolts-2 No's, Alluminium150mm long Handles-4 No's, door

stopper- 2 No's, including fixing the fixtures to door with

required number of screws , bolts and and nuts including

labour charges for fixing the frame in position, fixing the teak

wood shutter of 150x35mm with 12mm thick tougnend glass

fixing teak wood beading alround to the frame etc., applying of

bituminous paint and polish to the frame and shutters

including overheads & contractor profit complete for finished

item of work as per APSS 1001 & 1002 (The vertical frame of

door shall be embedded in flooring for a depth of not less than

10mm) (2400mmx2400mm) complete as per drawing etc.

Each 6.00 65613.43 393680.58

52






including MS Z hold fasts of size 300mmx40mmx5mm- 6 No's

,Alluminium Hinges of size 150mm long- 3 No's, Alluminium

Aldrop of size 300mm as per IS:2681- 1 No, Alluminium

200mmx10mm size tower bolts-1 No, Alluminium150mm long

Handles-2 No's, including fixing the fixtures to door with

required number of screws , bolts and and nuts including

labour charges for fixing the frame in position, fixing the teak

wood beading alround to the frame etc., applying of

bituminous paint and polish to the frame and shutters

including overheads & contractor profit complete for finished

item of work as per APSS 1001 & 1002 (The vertical frame of

door shall be embedded in flooring for a depth of not less than

10mm) (750mmx2100mm) complete as per drawing etc.

Each 24.00 11064.05 265537.20

Page 10 of 11

53










bolts-2 No's, Alluminium150mm long Handles including fixing

the fixtures to door with required number of screws , bolts and

and nuts including labour charges for fixing the frame in

position, fixing teak wood beading alround to the frame etc.,

applying of bituminous paint and polish to the frame and

shutters including overheads & contractor profit complete for

finished item of work as per APSS 1001 & 1002 (The vertical

frame of door shall be embedded in flooring for a depth of not

less than 10mm) (1500mmx2400mm) complete as per

drawing etc.

Each 10.00 23036.67 230366.70

54










bolts-2 No's, Alluminium150mm long Handles, door stopper- 2

No's, including fixing the fixtures to door with required

number of screws , bolts and and nuts including labour

charges for fixing the frame in position, fixing the teak wood

beading alround to the frame etc., applying of bituminous paint

and polish to the frame and shutters including overheads &

contractor profit complete for finished item of work as per

APSS 1001 & 1002 (The vertical frame of door shall be

embedded in flooring for a depth of not less than 10mm)

(1000mmx2400mm) complete as per drawing etc.

Each 10.00 15196.64 151966.40

918,34,095.83Civil Works Sub-total

Page 11 of 11

Sl. No Description of Work

UOM Quantity Rate(Rs)

Amount (Rs.)

1

Supply, Installation and commissioning approved makefloor mounted EWC (suit) CASCADE model 'P' or 'S' trap with

dual flush porcelain cistern fixed on EWC with all internal

parts of dual flush cistern, ultra solid seat cover of approved

make with rubber buffer and cap 15 mm angle stop cock 450

mm long PVC inter connection pipe wall flanges all of

approved make etc. complete for finished item of work in all

respects: White colour

Each 13.00 10007.21 130093.73

2

Supplying & Fixing Orissa Pan white glazed W.C 1st qualityISI marked conforming to IS:2556-Part-3-1981 with "P" or "S"

trap 580 mm x 440 mm including Brick masonry seat for

Orissa pan/ Indian W.C. using 2nd class bricks as per standard

practice, PVC low level system with internal components &

short bend: 10 Litres capacity Single Flush, 15 mm PVC

connection with brass union nut C.P coated and 15mm CP

finish brass stop valve. Complete for finished item of work.

Each 7.00 4006.06 28042.42

3

Supplying & Fixing Indian make Flat Back Wash HandBasin 1st quality conforming to IS:2556-Part-4:1972 with

waste fittings like rubber plug, chain, 32 mm nominal size C.P.

Fitting with parallel pipe thread conforming to IS:2963-1979

and fitted with 15 mm nominal bore Chromium Plated Pillar

Tap of 1st quality Indian make 400 grams complete with

standard CI brackets including wooden block:

a)550x400mm - Single C.P. Pillar cock Each 81.00 1840.56 149085.36

4

S&F of 15 mm brass body CP finish bib tap of not less than300 grams weight with quarter turn spindle with either

internal or external threaded conenction conforming to IS

8931 including cost & conveyance of all materials, labour

charges for finished item of work complete for all floors.

Each 24.00 680.55 16333.20

5

Manufacture, Supply and Delivery of Unplasticised PVCsPipes for potable water supplies conforming to IS :

4985/2000 (3rd revision) with bell ends (Socket) as per

specification in light Grey/Natural Ivory Grey/ Any other

Color (except White) inclusive of Excise duty,Sales Tax

,transportation etc

a)50 mm dia. @ 6 Kg/sq.cm Rmt 85.000 62.74 5332.90

b)75 mm dia. @ 6 Kg/sq.cm Rmt 85.000 137.50 11687.50

c)110 mm dia. @ 6 Kg/sq.cm Rmt 150.000 287.02 43053.00

d)160 mm dia. @ 6 Kg/sq.cm Rmt 125.000 612.75 76593.75

6

Supply & fixing SWG 150x100mm gully trap of 1st class asper IS -651 & 4127 with CI grating and constructing brick

masonry in CM 1:6 prop. Intermediate chamber and fitted

with 30.48x28.86cm CI frame and hinged coverfor finished

item of work

Each 16.00 677.15 10834.40

BILL OF QUANTITIES

Name of the work:Construction of Mess Block-Girls Kitchen and Dining Hall at IIIT Campus, RGUKT,Basar, Adilabad Dist., Telangana

SANITARY WORKS

Page 1 of 3

7

Constructing 904.0 mm (3’0”) dia solid block masonryinspection chamber as per IS - 4111: Part-1:1986 with

cement mortar (1:6) prop using fly-ash blocks of 225 mm thick

from approved source having a minimum crushing strength of

10 N/sq.mm including plastering with cement mortar 1:3

prop; ½” thick both inside and outside fitted with 20” dia RCC

manhole covers and frames including excavating pits up to a

depth of 904 mm (3'-0") in all sorts of soils (excluding rock)

and laying cement concrete (1:4:8) 150 mm thick using 40 mm

HBG Metal and P.C.C. 1:2:4 benching and channel 100 mm

thick as per Standard specification and including cost and

conveyance of all materials like cement, sand, bricks, water

etc., to site, cost of seigniorage charges on all materials and all

incidental and operational, labour charges like mixing cement

mortar, constructing masonry, lift charges, curing etc.,

complete for finished item of work as per Standard

specification with RCC cover 22" dia with nominal

reinforcement 3" thick and hooks for lifting etc., for finished

the item of work.

Each 4.00 7778.08 31112.32

8

Providing & fixing Bronze Ball valve with SS ball an SSspindle as per IS Class - 1, Indian make heavy type including

cost & conveyance of all material to work spot and all labour

charges including fixing in position for finished item of work. 0.00

a)20 mm NB size Each 2.00 341.98 683.96

b)25 mm NB size Each 6.00 480.59 2883.54

c)40 mm NB size Each 10.00 1173.64 11736.40

d)50 mm NB size Each 4.00 1763.30 7053.20

9

Supplying, laying, jointing and testing SWG SP-1 pipes ofISI make conforming to ISI 651 & 4127 with airtight cement

joints in CM 1.5:1 prop. Including excavation of trenches and

socket pits in any soil (except rock requiring blasting) up to

1524 mm(3'0") depth and refilling with watering and tamping

for finished item of work

a)101.6mm Rmt 100.00 485.14 48514.00

b)152.4mm Rmt 250.00 722.59 180647.50

10

Providing and fixing Chlorinated Polyvinyl Chloride(CPVC) -SDR-13.5 pipes, having thermal stability for hot &

cold water supply, including all CPVC plain & brass threaded

fittings i/c fixing the pipe with clamps at 1.00 m spacing. This

includes jointing of pipes & fittings, with one step CPVC solvent

cement and the cost ofcutting chases and making good the

same including testing of joints complete as per direction

ofEngineer-in-Charge.Concealed work, including cutting

chases and making good the wall etc

a)15.90mm OD Rmt 10.00 211.44 2114.40

b)22.20mm OD Rmt 302.00 235.18 71024.36

c)28.60mm OD Rmt 102.00 300.17 30617.34

d)34.90mm OD Rmt 192.00 396.40 76108.80

11

Providing and fixing Chlorinated Polyvinyl Chloride(CPVC) pipes-SDR-13.5, having thermal stability for hot &

cold water supply, including all CPVC plain & brass threaded

fittings including fixing the pipe with clamps at1.00 m spacing.

This includes jointing of pipes & fittings with one step CPVC

solvent cement and testingof joints complete as per direction

of Engineer-in-Charge.Internal work - Exposed on wall

a)15.90mm OD RMT 20.00 176.22 3524.40

b)22.20mm OD RMT 20.00 199.96 3999.20

Page 2 of 3

c)28.60mm OD RMT 20.00 264.95 5299.00

d)34.90mm OD RMT 20.00 361.18 7223.60

e)41.30mm OD RMT 99.00 449.92 44542.08

f)54.00mm OD RMT 220.00 656.13 144348.60

12

Supply and fixing 4" (101.6mm) multi floor trap with Jali-PVC/SWR pipe fittings of standard make of ISI Brand inculding

fixing in CM1:3 prop and cost and conveyance of all materials

at site complete for finished item of work

Each 130.00 163.61 21269.30

13Supplying and fixing TV shape mirror with plastic frame size609.6 mm x 457 .2 mm for finished item of work

Each 85.00 582.84 49541.40

14

Manufacture, Supply, & Delivery of HDPE Pipes PE-100conforming to IS 4984 - 1995 including laying,jointing and

transportation to any where in T.G, including excise duty, sale

tax and specials etc., complete.(supply upto 90 mm diain coil &

above 90 mm diastraight length in 6 m.) 6.0 kg/Sqcm

a)110mm dia Rmt 100.00 469.89 46989.00

b)160mm dia Rmt 100.00 943.69 94369.00

15

Providing & Placing on Terrace (at all floor levels)polyethylene water storage tank with Double layer approved

brand & manufacture with cover and suitable locking

arrangement & making necessary holes for inlet & outlets and

over flow pipes but without fittings & base support for tanks

for finished item of work

Litre 2000.00 6.82 13640.00

16

Supply and fixing Bronze Gate/ Globe valve as per IS - 778Class - I, Indian make heavy type - 65 mm NB Size for finished

item of work.

a)65mm NB Size Each 2.00 6510.14 13020.28

b)80mm NB Size Each 2.00 9650.46 19300.92

17

Supply and fixing of Stainless steel 4" dia round Grating withframe for nahany or floor trap cover with holes including

fittings, etc. For complete the item of work. Each 30.00 71.58 2147.40

18

Supply and fixing CP finish brass bottle trap 250 mm long withwall connection pipe & wall Flange etc., complete the finished

item of work Each 45.00 1079.34 48570.30

19

Supplying & Fixing white glazed flat back half stall urinals 1stquality conforming to IS:2556-1995 with standard C.P.

Spreader of overall size 95 x 95 x 57 mm conforming to

IS:2556-Part6, Sec-6-1974 fixed with screws complete Indian

make (HSW/Parry/Neycer) : 590 x 375 x 390 mm

Each 11.00 3201.67 35218.37

14,86,554.93Sanitary Works Sub-total

Page 3 of 3

PVC Conduit-ISI mark, Make:Sudhakar/Modi

1

Supply and Fixing of 20mm outer dia heavy grade, FRLS withIS:9537 part 3 regid PVC pipe concealed in wall with all

required accessories including masonary work for light, fan ,

common and separate plug point including all labour charges

etc., complete.

RM 50.00 77.15 3,857.50

2

Supply and Fixing of 25mm outer dia Medium grade, FRLSwith IS:9537 part 3 regid PVC pipe concealed in Roof Slabs

with all required accessories including masonary work and

labour charges etc., complete.

RM 6000.00 63.51 3,81,060.00

3

Supply and Fixing of 25mm outer dia Medium grade, FRLSwith IS:9537 part 3 regid PVC pipe surface with all required

accessories fixing on chromium plated metallic base saddles

including masonary work and all labour charges etc., complete

RM 400.00 72.08 28,832.00

4

Supply and Fixing of 25mm outer dia Medium grade, FRLSwith IS:9537 part 3 regid PVC pipe concealed in wall with all

required accessories including masonary work for light, fan ,

common and separate plug point including all labour charges

etc., complete.

RM 1125.00 79.06 88,942.50

5

Supply and Fixing of ISI 32mm outer dia 2.10mm(Medium)thick,FRLS with IS:9537 part 3 rigid PVC pipe concealed in

Roof Slabs with all required accessories including junction box,

bends, dummy covers and labour charges etc., complete

RM 500.00 85.53 42,765.00

6

Supply and Laying of P.V.C casing and caping of makesSudhakar / Maco Plast / Avon Plast / Modi (ISI MARK) with

double locking arrangments with groover trunking of size not

below 12.5mm height 25mm size with all accessories, duly

sealed at points and erected on Wall / Ceiling including cost of

all materials and labour charges complete.

RM 450.00 57.32 25,794.00

Point Wiring: Copper Wire Make:Finolex/Rrkabel,Modular switch:Legrand Arteor/Schneider Zen celo,

Ceiling Rose Make:Gold Medal Olive/ Million Zoom

7

Wiring with 2 runs of 14/0.3mm (1.0 Sqmm) HFFR PVCinsulated 1100V grade as per IS:694/1990 specification for

Copper cable in existing pipe with 6A / 10A 1 Way 1 Module

Modular Switch control with 6 Module Hot Dip Galvanized

modular type Metal Box covered with 6 Modular Cover Frame,

3 Plate Jumbo Ceiling Rose including all labour charges etc.,

complete for light, bell, fan and exhaust fan points in Non-

Residential Buildings.

Point 1600.00 597.61 9,56,176.00

8

Wiring with 2 runs of 14/0.3mm (1.0 Sqmm) HFFR PVCinsulated 1100V grade as per IS:694/1990 specification for

Copper cable in existing pipe with 6A / 10A 1way/2way 1

Module Modular Switch control with three way Jumbo Ceiling

Rose including all labour charges etc., complete for above

5.0mtr height/length and staircase points.

Point 500.00 896.42 4,48,210.00

Circuit Wiring: Make:Finolex/ RR kabel

9

Supply and run of 1 of 14/0.3mm (1.0 Sqmm) HFFR PVC insulated 1100V grade as per IS:694/1990 specification for

Copper cable in existing pipe for earth continuity including all

labour charges etc., complete.

RM

500.00 20.02 10,010.00

BILL OF QUANTITIES

Name of the work:Construction of Mess Block-Girls Kitchen and Dining Hall at IIIT Campus, RGUKT,Basar, Adilabad Dist., Telangana

ELECTRICAL WORKS

Page 1 of 5

10

Supply & run of main 2 of 1.5 sqmm HFFR PVC insulatedflexible copper wire in existing conduit pipe & in / on surface

pipe with 1 No. of 1.5 Sqmm earth continuity copper wire from

MCBDB to lighting switch boards point.

RM 1200.00 77.13 92,556.00

11

Supply and run of 2 of 36/0.3mm ( 2.5 sq mm ) HFFR PVCinsulated flexible copper cable and 1.5 sqmm wire for earthing

in existing pipe for power points including all labour charges

etc.,complete.

RM 2550.00 98.84 2,52,042.00

12

Supply and run of 2 of 56/0.3mm ( 4 sq mm ) HFFR PVCinsulated flexible copper cable and 2.5 sqmm wire for earthing


etc.,complete.

RM 1500.00 147.72 2,21,580.00

13

Supply and run of 2 of 140/0.3mm (10 sq mm ) HFFR PVCinsulated flexible copper cable and 4 sqmm wire for earthing


etc.,complete.

RM 100.00 307.45 30,745.00

14

Supply and run of 4 of 56/0.3mm ( 4 sq mm ) HFFR PVCinsulated flexible copper cable and 2.5 sqmm wire for earthing


etc.,complete.

RM 150.00 258.85 38,827.50

15

Supply and run of 4 of 85/0.3mm ( 6 sq mm ) HFFR PVCinsulated flexible copper cable and 4 sqmm wire for earthing


etc.,complete.

RM 500.00 368.48 1,84,240.00

16

Supply and run of 4 of 140/0.3mm ( 10 sq mm ) HFFR PVCinsulated flexible copper cable and 6sqmm wire for earthing in

existing pipe for power points including all labour charges

etc.,complete.

RM 500.00 536.67 2,68,335.00

Socket and switch make: Legrand Arteor/Schneider Zen celo

17

Supply and fixing of 6A / 10A 3/2 Pin 2 Module ModularSocket with shutter with 6A / 10A 1 Way 1 Module Modular

Switch control on a Common switch board with with 3

Module Hot Dip Galvanized Modular Metal Box covered with 3

Modular Cover Frame with earth continuity including wire

leads, earth connections along with all labour charges etc.,

complete.

Each 25.00 512.75 12,818.75

18

Supply and Fixing of 20A 2 Module Modular Socket withshutter and 16A / 20A 1 Way 1 Module Modular Switch duly

recessed in wall with 3 Module Hot Dip Galvanized Modular

Metal Box size covered with 3 Modular Cover Frame including

earth connections and all labour charges etc., complete.[

Power plug ]

Each 24.00 684.53 16,428.72

19

Supply and fixing of 6A / 10A 3/2 Pin 2 Module ModularSocket with shutter-2 Nos and 6A / 10A 1 Way 1 Module

Modular Switch controls-2Nos duly recessed in wall with 6

Module Hot Dip Galvanized Modular Metal Box size covered

with 6 Modular Cover Frame including earth connections and

all labour charges etc., complete.[ For computer switch board].

Each 60.00 974.25 58,455.00

Fixtures LED Make:Philips/CREE/NICHA/Osram,Luminaire Make : Phillips / Osram / GE

20

Supply and transportation of 20W, 2000 lumins, 1200mmlength LED retrofit T8 tube light, input voltage AC 165 - 260

Volts with >0.9 PF with inbuilt driver and frosted cover etc.,

complete with 3 years warranty

Nos 210.00 1590.61 3,34,028.10

Page 2 of 5

21

Supply and Transportation of 36W slim LED panel of 600mm x600mm made of alluminium body with acrylic diffuser,

Constant current out put of Driver operating voltage range of

150 to 265 Volts AC, Power factor > 0.9 high power LEDs

having efficacy of > 120 lumins/watt, junction temparature

less than 85 degrees centigrade and THD is less than 12% etc.,

complete with 3 years warranty

Nos 180.00 5021.78 9,03,920.40

22

Fixing of 20W/18W/36W/45W/70W led tube light luminaireon wall / Ceiling with / TW /PVC round blocks with all

accessories including giving connections and all labour

charges etc., complete.

Nos 390.00 119.86 46,745.40

23

Supply and fixing of batten holder / slanting holder with 7WLED lamp in lieu of ceiling rose of light point complete with all

connections and all labour charges without bulb (for new

installation).

Nos 53.00 562.11 29,791.83

Fan Makes : Crompton High Speed Decora / Havells Fusion50

24Supply of 48" (1200mm) Sweep 5 Star rated CeilingFan with Regulator.

Nos 128.00 3223.48 4,12,605.44

25

Labour charges for Fixing of Ceiling fan and regulatorincluding transportation and giving connections with twin

core wire etc., complete.Nos 128.00 153.12 19,599.36

26Supply and fixing of Fan hook box with dummy cover etc.complete for finished item of work

Each 128.00 118.16 15,124.48

Exhaust fan Makes : Crompton / Havells Ventil Air-DB /Orient hill air.

27Supply of 18" (450mm) ISI, 900 RPM Heavy duty exhaust fanwith wire guard etc complete etc., complete.

Nos 60.00 4704.80 2,82,288.00

28

Labour charges for fixing of Exhaust fan in wall with necessaryconnections and masonary work of making hole, finishing etc.,

completeNos 60.00 533.02 31,981.20

Distribution Board, Isolator and MCB Makes : Legrand /Schneider. MCCB make:L&T/Siemens/Legrand

29

Supply and fixing of 12 Way SPN DB with IP 43 Protection asper IS:13032 concealed in wall and suitable for singile phase

10 Nos S.P out goings and for 1No Incommer including internal

connection and labour charges for flush mounting etc.,

complete.

Incommer: 32A DP Isolator-1No.

Outgoing: 10kA-6-32A SP MCBs - 10 Nos

Nos 1.00 5900.74 5,900.74

30

Supply and fixing of 4 Way TPN DB Horizontal with IP 43Protection as per IS:13032 concealed in wall and suitable for

12 Nos S.P.out goings and for 1 No 4 pole Incommer including

internal connection and labour charges for flush mounting

etc., complete.Incommer: 40A FP Isolator-1No.

Outgoing: 10kA-6-32A SP MCBs - 12 Nos

Nos 5.00 8245.75 41,228.75

31

Supply and fixing of 4 Way VTPN DB suitable for accomodating 63A4 Pole Isolator as incomer 6-32A SP MCB - 10KA - 12No's asoutgoing and with IP 43 Protection including internal connectionand labour charges for surface / flush mounting etc., complete. Incommer: 63A FP Isolator-1No.. Outgoing: 32A SP MCB - 10KA - 12 Nos

Nos 4.00 12608.29 50,433.16

Page 3 of 5

32

Supply and fixing of 4 Way VTPN DB suitable for accomodating125A 4 Pole MCCB as incomer and 40/63A,10KA, TP MCBs-4

Nos as outgoing and with IP 43 Protection including internal

connection and labour charges for surface / flush mounting

etc., complete.

Incommer: 125A 4 Pole MCCB, Adjustable, Confirms to

IS/IEC 60947-2 having Breaking Capacity 25 KA with

thermal magnetic release Panel Mounted-1No.

Outgoing: 32A SP MCB - 10KA - 12 Nos

Nos 5.00 26709.18 1,33,545.90

33

Supply and fixing Distribution board with 20A SP Plug andSocket with SS enclosure concealed in wall with 20A 10KA SP

MCB, C/D Curve ISI Mark including internal connection and

labour charges for surface / flush mounting etc., complete .Nos 5.00 2159.54 10,797.70

34

Supply and fixing of 32A DP MCB with metal encloser includingwire leads, earth connections along with all labour charges

etc., complete. For power pointsNos 5.00 1195.80 5,979.00

35

Supply and fixing of 32A FP MCB with metal encloser includingwire leads, earth connections along with all labour charges

etc., complete. For power pointsNos 5.00 2131.13 10,655.65

LT PANELS -

36

Main LT Panel Board:Fabrication ,Transportation , Supply, Installation, Testing and

Commissioning of suitable size , plinth mounting indoor type

LT Distribution panel of 14 guage CRCA sheet with the

following incorporated in the panel for Distributing the power

supply .(The working drawings for panel board should be got

approved by the Department before fabrication of Panel).

Main incoming:400A 4 Pole MCCB / Confirms to

IS/IEC 60947-2 having Breaking Capacity

50 KA with thermal magnetic release Panel

Mounted of makes L&T / Schneider / Hager -1No.

300A Alluminium Bus bar

(40mmx10mmxSuitable lenght) - 4nos -Main

Sleaves tape for bus bar R Y B N-required length

Insulators for busbar fixing (panel type)-8 Nos

Phase indicator lamps - 1set (L&T make)

Extended earth terminals - 2nos with 40X6 mm G.I Strip - 1.3

Mtrs

Current Transformer- 230/5A - 3 NosKAPPA make

Voltmeter(0-500V) - Digital type ( conzerv/HPL Make)

Ammeter (0-500A) - Digital type ( conzerv/HPL Make)

supply of HRC Fuse links 2A - 3 Nos

SET 1.00 138335.02 1,38,335.02

Outgoing :1)125A, FP MCCB Adjustable, Confirms to IS/IEC60947-2 having Breaking Capacity 25 KA with thermal

magnetic release Panel Mounted-4 No's. 2)63A TP 10kA MCB-2

No's The panel Size approx:1.5X1.8X0.40 mtrs The above Panel

shall be cleaned with 7 tank process and painting with one

coat of red oxide and two coats of powder coated light grey

as per IS 631 of (5) etc complete and provided suitable base

channel of 75X40mm size etc., complete as directed by the

Engineer- in - Charge.

-

Cables: Makes : Torrent / Universal/KEI -

37

Supply of 70 Sqmm 3.5 Core XLPE insulated, 1100Vgrade armoured alluminium cable as per specification

confirming to IS:7098 (Part - I).RMT 50.00 478.32 23,916.00

Page 4 of 5

38



39



40

Supply of 300 Sqmm3.5 Core XLPE insulated, 1100Vgrade armoured alluminium cable as per specification

confirming to IS:7098 (Part - I).RMT 300.00 1646.28 4,93,884.00

-

Glands

41

Supply and Fixing of Single compression brass cable glands for3.5 core XLPE armoured cable for 70 Sqmm with brass

washers and crimping type aluminium lugs confirming to I.S

specifications for cable of 70 Sq.mm including nuts and bolts

with connections.

SET 8.00 517.62 4,140.96

42




with connections.

SET 2.00 868.87 1,737.74

43




with connections.

SET 2.00 1080.42 2,160.84

44




with connections.

SET 2.00 1292.37 2,584.74

45

supply and installation of 450MMX50mmX2mm thick GIperforated cable tray with cover along with required angle

supports with coupler plates, anchor bolts and nuts etc.,

complete. And the tray should be fitted on wall/ceiling/

coridor etc., complete.

RM 10.00 960.05 9,600.50

46

Providing independent earthing for Important equipment with40mm dia 'B' class 2.5m long G.I pipe and 19mm dia 'B' class

G.I pipe of 0.3mtr. long connected with reducer providing G.I

funnel with mesh enclosed in brick masonry (CM 1:3)

Chamber of 400mmx 400m x 400mm with suitable cast iron

cover duly providing staggered holes filling with salt and

charcoal from the bottom of the pipe giving earth connection

from electrode through G.I strip of 25 x 6mm x 200mm length

with all accessories and labour charges complete, as per IS

specifications 732/1982 (Part II)

Each 2.00 5160.49 10,320.98

47Supply and Run of 25mm x 6mm G.I Strip including cost of allaccessories and labour charges etc., complete. RM 190.00 111.96 21,272.40

48Supply and Run of No.8 SWG G.I wire including cost of allaccessories and labour charges etc., complete.

RM 100.00 17.87 1,787.00

49

Earth work excavation of Trench in hard ground soil, laying ofU.G cables from 70 sqmm to 400 Sq,mm on sand cushion

covering the cable with bricks and back filling of Trench duly

providing route indicator embedded in C.C including cost and

conveyance of materials and labour charges etc., complete.

RM 300.00 406.87 1,22,061.00

63,52,176.26Electrical works Sub-Total

Page 5 of 5

mailto:VAT@%204%25

mailto:VAT@%204%25

mailto:VAT@%204%25

mailto:VAT@%204%25

mailto:VAT@%204%25

mailto:VAT@%204%25

mailto:VAT@%204%25

mailto:VAT@%204%25

mailto:VAT@%204%25

mailto:VAT@%204%25

mailto:VAT@%204%25

mailto:VAT@%204%25

mailto:VAT@%204%25

mailto:VAT@%204%25

mailto:VAT@%204%25

mailto:VAT@%204%25

mailto:VAT@%204%25

mailto:VAT@%204%25

mailto:VAT@%204%25

mailto:VAT@%204%25

mailto:VAT@%204%25

mailto:VAT@%204%25

mailto:VAT@%204%25

mailto:VAT@%204%25

mailto:VAT@%204%25

mailto:VAT@%204%25

mailto:VAT@%204%25

mailto:VAT@%204%25

mailto:VAT@%204%25

mailto:VAT@%204%25

mailto:VAT@%204%25

mailto:VAT@%204%25

mailto:VAT@%204%25

mailto:VAT@%204%25

mailto:VAT@%204%25

mailto:VAT@%204%25

mailto:VAT@%204%25

mailto:VAT@%204%25

mailto:VAT@%204%25

mailto:VAT@%204%25

mailto:VAT@%204%25

mailto:VAT@%204%25

mailto:VAT@%204%25

volume iii price bid/boq - engineering projectsusing hydraulic piling rig with power unit and...

Documents