vs096f111-8 fv4.0 130608 1by1 · 2020. 12. 9. · ver fv4.0 2010.04.12 signature date led dot...
TRANSCRIPT
-
VISSEM ELECTRONICS CO., LTD
R&D DIVISION
395, Cheongdeok-dong, Giheung-gu, Yongin-city,
Gyeonggi-do, KOREA 446-915
TEL: +82-31-288-3427~29,20
FAX: +82-31-288-3490~1
HTTP://WWW.VISSEM.COM
VS096F111-8 1ⅹ1 Type
ISSUED DATE 2008.06.14 ITEM DESIGN CHECK APPROVAL
VER FV4.0 2010.04.12
SIGNATURE
DATE
LED DOT MATRIX MODULE
-
1.MODEL NAME : VS096F111-8
2. FEATURES
ITEM DESCRIPTION Display Color Full Color
Structure
Size(W X H X D) 96 X 96 X10.1(mm)
Dot Pitch 6(mm)
Number Of Dots 256(16×16) Dots
Leds Per Dot R:1, PG:1, B:1 (3-In-1 3528 SMD LED)
Weight Max.120(g)
Drive Mode 1/8 Duty Drive
Application Indoor
3. ABSOLUTE MAXIMUN RATINGS
ITEM SYMBOL VALUE UNIT REMARK
Supply Voltage VLED 0~+5.5
V VCC 0~+6.0
Signal Input Voltage Level VIH, VIL -0.3~ VCC+0.3 V
Operating Temperature TOP[1] -20 ~ +50 ℃ On Dots=100%
-20 ~ +60 ℃ On Dots=30%
Storage Temperature Tstg -25 ~ +80 ℃
NOTES : [1] Temperature of led surface’s should be remained below 70℃ in case of necessity, led system requires cooling fan. Maintained at less than 80% relative humidity, and no dew condensation shall
take place.
4. RECOMMENDABLE OPERATING CONDITIONS
ITEM SYMBOL MIN. TYP. MAX. UNIT REMARK
Supply Voltage LED VLED 4.75 5 5.25
V
Logic Circuit VCC 4.75 5 5.25
Signal Input Voltage Level VIH 0.8×VCC - VCC
VIL 0 - 0.3×VCC
Operating Temperature TOP -15 ~ +45 ℃
5. ELECTRICAL CHARATERISTICS (AT Ta = 25℃)
ITEM SYMBOL VALUE UNIT REMARK Clock Frequency F MAX.16 ㎒
Current Consumption For Module ILED MAX. 2.0
A ALL On ICC MAX.0.5
MODEL VERSION UP DATE PAGE
VS096F111-8 2010.04.12 1/14
-
6. OPTICAL CHARACTERISTICS( AT Ta = 25℃)
ITEM SYMBOL MIN. TYP. MAX. UNIT REMARK
Brightness
RED
LV
900 - -
cd/㎡ GREEN 2,300 - -
BLUE 350 - -
WHITE 3,500 - -
Wavelength
RED
λp
620 - 630
nm GREEN 523 - 532
BLUE 465 - 475
Viewing Angle HOR.
2θ1/2 - 120 -
deg(°) Half Value VER. - 120 -
[REFERENCE] These are just brightness of standard model. If you have any questions about higher brightness, Please contact us.
7. SIGNAL FUNTION
1) DATA SIGNAL CONNECTOR
PIN MAP (IN) PIN NUMBER PIN NAME FUNCTION DESCRIPTION
1,2 G1,G2 Data Input For Green Color 3,4 R1,R2 Data Input For Red Color 5,6 B1,B2 Data Input For Blue Color
7[MSB],8,9[LSB] A[2:0] 3Bits Line Address 10 GCLK-G Clock Input for Green Gray Scale 11 GCLK-R Clock Input for Red Gray Scale 12 GCLK-B Clock Input for Blue Gray Scale 13 LATCH Data Strobe 14 GND Ground Of The Module 15 SCLK Shift Clock For Input Data
16 DEN Line Decoder Enable Signal
PIN MAP (OUT) PIN NUMBER PIN NAME FUNCTION DESCRIPTION
1,2 G1,G2 Data Output For Green Color 3,4 R1,R2 Data Output For Red Color 5,6 B1,B2 Data Output For Blue Color
7[MSB],8,9[LSB] A[2:0] 3Bits Line Address 10 GCLK-G Clock Input for Green Gray Scale 11 GCLK-R Clock Input for Red Gray Scale 12 GCLK-B Clock Input for Blue Gray Scale 13 LATCH Data Strobe
14,16 GND Ground Of The Module 15 SCLK Shift Clock For Output Data 16 DEN Line Decoder Enable Signal
MODEL VERSION UP DATE PAGE
VS096F111-8 2010.04.12 2/14
◀NO.1 2
16 15
TOP VIEW
TOP VIEW
◀NO.1 2
16 15
-
2) POWER CONNECTOR
PIN MAP(POWER) PIN NUMBER PIN NAME FUNCTION DESCRIPTION
1 VCC Supply Voltage For IC
2,3 VLED Supply Voltage For LED
4,5,6 GND Ground Of The Module
3) CONNECTOR CABLE SPECIFICATION - DATA CABLE
- POWER CABLE
※ This connectors can be changed without a previous notice for quality improvement.
CONNECTOR VENDOR MODEL NO. SPECIFICATION HOUSING MODEL NO.IN,OUT DATA YENSEN CONNECTOR YSF51643B2R 16PIN, 1mm PITCH FPC-16-120MM
POWER YEONHO CONNECTOR SMW200-06G 6PIN, 2mm PITCH SMH200-06
MODEL VERSION UP DATE PAGE
VS096F111-8 2010.04.12 3/14
TOP VIEW
◀No.1
110mm 5mm5mm
200mm
-
8. SIGNAL & POWER CABLE CONNECTION
1) DIRECTION OF DATA
2)SIGNAL CABLE CONNECTION EXAMPLE
MODEL VERSION UP DATE PAGE
VS096F111-8 2010.04.12 4/14
GREEN1,GREEN2,RED1,RED2,BLUE1,BLUE2_DATA, SCLK,
GCLK-G, GCLK-R, GCLK-B, LATCH,LINE ADDRESS(A0~A2),GND
DEN
▶VS096F111-8 IS CONSIST OF 1PCS
96Ⅹ96mm(16Ⅹ16 Dots)
1 2 3 4 5 6 7 8 ‥‥‥ 13 14 15 16 1 2 3 4 5 6 7 8 ‥‥‥ 13 14 15 160
1
2
·
·
·
·
·
·
·
14
15
DIRECTION OF DATA SHIFT
MODULE(A) MODULE(B)
FRONT VIEW
REAR VIEW
MODULE
(1,1)
MODULE
(1,2)
MODULE
(1,3)
MODULE
(1,4)
MODULE
(2,1)
MODULE
(2,2)
MODULE
(2,3)
MODULE
(2,4)
INTERFACE
- CIRCUIT
CONNECTOR & CABLE
IN OUT
IN OUT
-
9. BLOCK DIAGRAM
MODEL VERSION UP DATE PAGE
VS096F111-8 2010.04.12 5/14
A0
16 CHANNEL
LED DRIVER
16 CHANNEL
LED DRIVER
16Ⅹ8 LED DOT MATRIX
16Ⅹ8 LED DOT MATRIX
3 TO 8
LINE DECORDER
&
DRIVER
16 CHANNEL
LED DRIVER
16 CHANNEL
LED DRIVER
GCLK B GCLK_B_OUT
LATCH_OUT
CLOCK_OUT
LATCH
CLOCK
A2
GCLK_G
GRN1
GRN2
BLUE1
BLUE2
A1
GRN1_OUT
GRN2_OUT
BLUE1_OUT
BLUE2_OUT
G_VR
B_VR
A0_OUT
A1_OUT
A2_OUT
GCLK_G_OUT
16 CHANNEL
LED DRIVER
16 CHANNEL
LED DRIVER
GCLK_R GCLK_R_OUT
R_VR
RED1
RED2
RED1_OUT
RED2_OUT
DEN DEN_OUT
-
10. TIMMING CHART
MODEL VERSION UP DATE PAGE
VS096F111-8 2010.04.12 6/14
-
◆Switching Characteristics
Characteristics Symbol condition Min. Typ. Max. Unit
Setup Time
SDI - DCLK↑ tSU0
VDD=5V
VIH=VDD
VIL=GND
REXT=700Ω
VDS=1V
RL=200Ω
CL=10pF
C1=100nF
C2=10uF
CSDO=10pF
1 - - ns
LE↑ -DCLK↑ tSU1 1 - - ns
LE↓ -DCLK↑ tSU2 5 - - ns
Hold Time DCLK↑ -SDI tH0 3 - - ns
DCLK↑ -LE↓ tHI 7 - - ns
Propagation Delay Time
DCLK - SDO tPD0 - 25 33 ns
GCLK - OUT4n* tPD1 - 50 - ns
LE - SDO tPD2** - 30 40 ns
Staggered Delay of Output
OUT4n+1* tDL1 - 2 - ns
OUT4n+2* tDL2 - 4 - ns
OUT4n+3* tDL3 - 6 - ns
Pulse Width
LE tW(L) 5 - - ns
DCLK tW(DCLK) 15 - - ns
GCLK tW(GCLK) 15 - - ns
Output Rise Time of Output Ports tOR 15 25 - ns
Output Fall Time of Output Ports tOF 10 15 - ns
Error Detection Minimum Duration tEDD 425 500 575 ns
Refer to the Timing Waveform, where n=0, 1, 2, 3
In timing of “Read Configuration” and “Read Error Status Code”, the next DCLK rising edge should be tPD2 after
the falling edge of LE.
MODEL VERSION UP DATE PAGE
VS096F111-8 2010.04.12 7/14
Vcc=5V, Ta=25℃
-
◆Principle of Operation
Control Command
Signals Combination Description
Command Name LE
Number of DCLK
Rising Edge when
LE is asseted
The Action after a Falling Edge of LE
Data Latch High 0 or 1 Serial data are transferred to the buffers
Global Latch High 2 or 3 Buffer data are transferred to the comparators
Read Configuration High 4 or 5 Move out "configuration register" to the shift registers
Enable "Error detection" High 6 or 7 Detect the status of each output's LED
Read "Error status code" High 8 or 9 Move out "error status code" of 16 outputs to the shift
registers
Write Configuration High 10 or11 Serial data are transferred to the "configuration register"
Reset PWM Counter High 12 or13 If bit "B" of the configuration register is set to "1", this
command will reset PWM counter.
MODEL VERSION UP DATE PAGE
VS096F111-8 2010.04.12 8/14
-
◆Definition of Configuration Register
F E D C B A 9 8 7 6 5 4 3 2 1 0
Ex) Default Value
F E D C B A 9 8 7 6 5 4 3 2 1 0 0 0 1 1 0 1 8’b10101011 0 0
Bit Attribute Definition Value Function
F Read/Write Data Loading 0(Default) 15 times of "data latch" +1 "global Latch"
1 16 times of "data latch" +1 "global Latch"
E Read Thermal error flag 0(Default) Safe(OK)
1 Over temperature(>150 typ.)℃
D Read X 1 Reserved bit
C Read/Write PWM counting mode selection
0 64times of MSB* 6bit PWM counting plus once of LSB 6bit PWM counting
1(Default) 12bit PWM direct counting
B Read/Write PWM counter reset
0(Default) Disable
1 Enable with 12 or 13 DCLKs(rising edge) when LE is asserted
A Read/Write PWM data synchronization mode
0 Auto-synchronization
1(Default) Manual synchronization
9~2 Read/Write current gain adjustment
00000000 ~ 11111111
8'b10101011(Default)
1 Read/Write Thermal protection 0(Default) Disable
1 Enable, 25% of setting output current if TTF>150℃
0 Read/Write Time-out alert of GCLK disconnection
0(Default) Enable
1 Disable
Please refer to “Setting the PWM Couting Mode” Section.(Next Page)
MODEL VERSION UP DATE PAGE
VS096F111-8 2010.04.12 9/14
MSB LSB
-
◆Setting the PWM Gray Scale Counter
LED MODULE Driver ic provides a 12bit color depth. The value of each 16bit serial data input will be valid only for 12bits and implemented according 12bit PWM counter.
◆Setting the PWM Counting Mode
MODEL VERSION UP DATE PAGE
VS096F111-8 2010.04.12 10/14
-
11. DIMENSION
MODEL VERSION UP DATE PAGE
VS096F111-8 2010.04.12 11/14
주의
1. M
3*8(
샘스
볼트
:스프
링,
평와
샤 붙
이 볼
트)
2. M3*6(일반볼트)
볼트
기장
이 위
에 정
해놓
은 수
치보
다 긴
볼트
는 사
용하
지 말
것.
(타공
판 철
판 두
께 1
.2~1
.6T
기준
)
-
** Hole for assemble between unit case and module.
MODEL VERSION UP DATE PAGE
VS096F111-8 2010.04.12 12/14
Plate Work
-
12. SAFETY
● Precautions in installing LED Module 1. Please escape the place where electromagnetic wave and noise is, which might cause
malfunction to LED module, when install LED Display Board. 2. Since over voltage and reverse voltage might cause the problem in internal circuit and LED,
please make sure and check the input voltage range, before operation. 3. Please escape the high humidity and leakage place which cause the LED module to be
broken. 4. The temperature of the surface of LED module shall be under 70 during operation.℃ 5. Heating from LED might cause damage in LED module or/and malfunction in LED display
board, user shall prepare suitable ventilation and cooling facility. 6. Even though the brightness become lower and lower, after long time use, it's prohibited to
input over voltage in order to increase the brightness, which might cause severe damage to LED Module. For the best operation, user shall operate LED module according to data sheet.
7. Please turn off the power supply, when display data are not charged. 8. Please be careful not to exposure LED Module to the dust, dirt, base, gas and other noxious
gas, when install LED Display. 9. User shall consider the weight of LED module enough, when prepare steel structure and
install LED Display Board.
MODEL VERSION UP DATE PAGE
VS096F111-8 2010.04.12 13/14
-
● Precautions in installing LED Module
1. Any jumper and switch is set up properly before delivery, please do not modify or/and
change setting without consulting with manufacturer. 2. The circuit part of LED Module include CMOS components, please treat carefully with
consideration of static electricity 3. Impact and vibration to LED Module might be the reason of disconnection and dot off, please
escape those factors. 4. It's highly recommended to escape the high temperature & humidity and be careful not to
exposure LED module to dust, dirt, base and SO2 Gas and other noxious Gas in order to escape the potential problem.
5. Please be careful not to be scratched and hurt on the surface of LED module. 6. It's prohibited to clean up LED module with solvent. In order to clean up LED module, it's highly recommended to use a piece of dried cloth and
smooth brush. 7. Stacking LED modules without anti-impact material and wearing out the surface or/and edge
of LED modules might cause fatal problem. 8. It's highly recommended to use twisted cable or shielded wire in order to remove the noise
from high frequency. 9. When user use and store LED module, please pack LED module with anti-static material.
WWW.VISSEM.COM
MODEL VERSION UP DATE PAGE
VS096F111-8 2010.04.12 14/14