wavin and osma below ground & civils systems · the trigon pipe is kitemarked to wis 4-32-19...

www.wavin.co.uk

Trade Price List 1st March 2020

Wavin and OSMA Below Ground & Civils Systems

1

Contents

Introduction to Osma 2Introduction 2Acceptance 3

OsmaDrain 4-13Building drainage system 110-160mm 4

Osma UltraRib 14-16Foul and Surface Water drainage system150-300mm 14

Osma Inspection Chambers 17-24Shallow Inspection Chambers 17Multi-base Inspection Chambers 18-19Universal Inspection Chambers 20-22Non Man-entry Inspection Chambers 23-24

Wavin Inspection Chambers 25-33Non Man-entry Inspection Chambers:Range 200 25Non Man-entry Inspection Chambers:Range 315 26-27Non Man-entry Inspection Chambers:Range 450 28-30Non Man-entry Inspection Chambers:Range 600 31-32Inspection Chambers – Ancillaries 33

Osma Domestic Channels 34Domestic Channel Drainage 34

Wavin Civils Channel 35-37Channels, gratings and accessories 35-37

Wavin TwinWall 38-43Surface water drainage system100-600mm 38-43

WavinCoil 44Land Drainage 80-160mm 44

Wavin MDPE 45Potable water pressure pipe system20-63mm 45

Wavin Trigon 46-47Barrier pressure pipe potable water system25-63mm 46-47

Introduction to Wavin Stormwater Management Systems 48Wavin AquaGrid 49Plastic Pervious Paving system 49

Wavin Vortex Valves 50Vortex Flow Control Valves 50

Wavin AquaCell 51-52AquaCell system 51-52

Wavin Q-Bic Plus 53-54Inspectable & cleanable infiltration/attenuation system 53-54

Wavin Garastor 55Garastor system 55

Wavin Temporary Manhole Cover 56Temporary Manhole Cover 56

Osma Geotextile 57Geotextile products 57

Numerical Index 58-61Notes 62-63Important Notes 64

Page Page

Introduction to

Osma Below Ground Drainage systems, form part of a comprehensive range of plastic systems to provide intelligent solutions for all building, construction and utilities projects.

Key to abbreviations

P/E – Pipe and fittings with both ends plain or with one plain end and one special end.

S/S – Pipe and fittings with one or more ring-seal or push-fit sockets, but always

one plain or special end.

D/S – Fittings with ring-seal or push-fit sockets at all ends.

S/SW – Fittings with one or more ring-seal sockets but always one solvent socket.

Symbols

! British Standards Kitemark

Identifies pipe and fittings manufactured under the BSI Kitemark Certification Scheme.

$ British Board of Agrément

BBA logo identifies non-Kitemarked fittings covered by a British Board of Agrément Certificate.

Water Regulations Advisory Scheme

Identifies pipe and fittings that are WRAS approved.

WIS Water Industry Specification

WIS identifies products that conform to Water Industry Specifications.

CE Marking

CE identifies product manufactured in accordance with a harmonised European Norm (hEN) accompanied with a declaration of performance (DoP).

Important notes:

OsmaDrain fittings must be ordered in their pack multiples as illustrated in price

list.

Product photos are for example only and not representative of every fitting size.

Free delivery is subject to minimum order values as stated in your Wavin

agreement.

Email: [email protected] Web: www.wavin.co.uk @WavinUK

2

Introduction

Introduction to Osma

3

a) British Standards Institution

! Osma/Wavin below ground drainage systems comply where applicable with the requirements of the following British Standards:

BS EN 124:1994 Gully tops and manhole tops for vehicular and pedestrian areas.

BS EN 1401-1:2009 Plastics piping systems for non-pressure underground drainage and sewerage.

BS EN 1433:2002 Drainage channels for vehicular and pedestrian areas – Classification, design and testing requirements, marking and evaluation of conformity.

BS EN 13476 – 2 Plastics piping systems for non-pressure underground drainage and sewerage – PVC-U.

BS EN 13598 – Parts 1&2 Plastics piping systems for non-pressure underground drainage and sewerage.

BS 4660:1989/2000 Unplasticized polyvinyl chloride (PVC-U) pipes and plastics fittings of nominal size 110mm and 160mm for below ground

gravity drainage and sewerage.

BS 7158:2001 Plastics inspection chambers for drains and sewers – Specification.

BS 4962:1989 Plastic pipes for use as light duty sub-soil drains.

! WavinCoil pipe complies with BS4962 requirements and carries the BSI Kitemark.

! UltraRib pipes and fittings (where applicable) comply with the requirements of the following:

BS EN 13476 – 3 Plastics piping systems for non-pressure underground drainage and sewerage.

Water Industry Specifications (WIS): WIS 4-35-01 July 2000: Issue 1.

Specification for Thermoplastics Structured Wall Pipes, Joints and Couplers with a smooth bore for gravity sewers for the size range 150-900 inclusive.

Medium Density Polyethylene pipes up to nominal size 63mm. Kitemarked to

BS EN 12201-2:2003 (KM 80817).

The Trigon pipe is Kitemarked to WIS 4-32-19 (KM 533039).

The Trigon pipe is approved under Regulation 31 (England and Wales).

Regulation 27 (Scotland) and Regulation 30 (Northern Ireland) N.B. Formally Regulation 25.

Trigon fittings are WRc, DVGW and KIWA approved.

Trigon has full system approval under WRAS Certificate No. 0409106.

b) British Board of Agrément $ Agrément Certificates have been awarded to the following systems:

87/1835 OsmaDrain Underground Drainage System.

10/H151 UltraRib HAPAS Roads and Bridges Highway Drainage System – 150mm, 225mm and 300mm.

98/3472 UltraRib Gravity Sewerage System – 150mm, 225mm and 300mm.

14/H214 UltraRib and TwinWall Road Gullies.

02/3940 TwinWall Drainage System.

03/4018 AquaCell Stormwater Management System.

02/H070 HAPAS Wavin TwinWall Highway Drainage.

Acceptance

4

OsmaDrain

ODR

Building drainage system 110-160mm

Description Nom dia mm

Cat no

Pack qty

Price £ per piece

PipeP/E Pipe 3.0m a 110 4D073 50 53.833.0m a 160 6D073 25 123.48

P/E Pipe6.0m a 110 4D076 50 107.66

6.0m a 160 6D076 25 246.99

Slotted PipeP/E Pipe6.0m a 110 4D066 50 168.046.0m a 160 6D066 25 341.79

CouplersD/S Coupler 110 4D104 10 21.01– for jointing OsmaDrain slotted pipe 160 6D104 1 38.55

D/S Slip Coupler – for new branch entry connections and repairs

a 110 4D105 10 32.32 a 160 6D105 1 78.50D/S Pipe Coupler – for jointing OsmaDrain pipe

a 110 4D205 20 19.58 a 160 6D205 1 39.23

SocketS/S Settlement Socket– expansion joint, installed vertically to accommodate differential settlement

110 4D115 1 57.27

SleeveProtection Sleeve 110 4D131 5 128.73– for protection of pipe passing through walls

AdaptorsD/S Adaptor to Clay– for connecting 110mm OsmaDrain 110 4D127 10 72.44to HepSleve 160 6D127 5 157.40

D/S Adaptor 110 4D129 1 57.39– to BS EN 295 thinwall clay spigot 160 6D129 1 138.85

Rainwater Adaptor– for connecting 68mm round PVC–U RW pipe to OsmaDrain socket or spigot, external use only

110 4D149 5 15.21

5


Cat no

Pack qty

Price £ per piece

Universal Rainwater Adaptor– for connecting square/round rainwater downpipes up to 70mm, or waste pipe from 32mm up to 50mm, to 110mm OsmaDrain socket or spigot, external use only

110 4D159 10 16.20

D/S Adaptor to Waste Pipe – 32mm 110 4D287 10 16.23– 40mm 110 4D288 10 16.23– 50mm 110 4D286 10 18.19

Internal Drain Connector– for 32mm/40mm waste pipe 110 4D298 5 17.17

Internal Drain Connector – for 50mm waste pipe 110 4D299 5 19.77

Adaptor– to soil stacks 110 4D464 10 51.77

Temporary Site Cap– for blanking off a 110mm OsmaDrain socket or spigot

110 4D295 20 5.72

ReducersS/S Level Invert Reducer – to 82mm OsmaDrain 110 4D095 5 44.34S/S Level Invert Reducer – to 110mm OsmaDrain 160 6D099 1 64.41

Short Radius BendsSingle SocketS/S Short Radius Bend – 87.5°

a 110 4D161 10 47.19 a 160 6D161 1 120.46

S/S Short Radius Bend – 67.5° a 110 4D162 5 51.06

S/S Short Radius Bend – 45º a 110 4D163 10 47.19 a 160 6D163 1 120.46



S/S Short Radius Bend – 11.25º a 110 4D168 5 45.46

6

OsmaDrain

ODR



Cat no

Pack qty

Price £ per piece

Double SocketD/S Short Radius Bend – 87.5°

a 110 4D561 10 55.87 a 160 6D561 1 133.10

D/S Short Radius Bend – 67.5° a 110 4D562 5 60.44

D/S Short Radius Bend – 45º a 110 4D563 10 55.87 a 160 6D563 1 133.10



D/S Short Radius Bend – 11.25º a 110 4D568 5 54.09

Adjustable BendsS/S Bend – 0º to 30º– for variable angles up to 30º, rotate segments to achieve required angle $ 110 4D173 1 57.29

D/S Bend – 0º to 30º– for variable angles up to 30º, rotate segments to achieve required angle $ 110 4D573 1 66.84

Long Radius BendsPlain EndedP/E Bend – 90º 110 4D281 1 104.69

160 6D281 1 283.09P/E Bend – 45º

a 110 4D283 1 89.69 a 160 6D283 1 174.09

Single SocketS/S Bend – 87.5°– with spigot length 900mm effective

a 110 4D181 1 206.12S/S Bend – 45º– manufactured with cut out marks to convert bend to a channel bend for use with traditional manholes

a 110 4D183 1 105.81

7


Cat no

Pack qty

Price £ per piece

Double SocketD/S Bend – 87.5°– satisfies recommendations of BS EN 12056: 2000 for base of soil stack applications. Manufactured with cut out marks to convert to a channel bend for use within traditional manholes

a 110 4D581 5 90.45

D/S Bend – 45º– manufactured with cut out marks to convert bend to a channel bend for use within traditional manholes

a 110 4D583 1 118.00

Equal JunctionsS/S Junction – 87.5°

a 110 4D190 5 66.64 a 160 6D190 1 217.52

D/S Junction – 87.5° a 110 4D193 5 75.32 a 160 6D193 1 240.38

S/S Junction – 45º a 110 4D210 5 69.55 a 160 6D210 1 198.79

D/S Junction – 45º a 110 4D213 5 78.22 a 160 6D213 1 219.68

Unequal JunctionsS/S Junction – 87.5°– 160mm x 110mm

a 160 6D198 1 167.67

D/S Junction – 87.5° – 160mm x 110mm

a 160 6D199 1 185.29

S/S Junction – 45º – 160mm x 110mm

a 160 6D218 1 171.21

D/S Junction – 45º – 160mm x 110mm

a 160 6D219 1 189.19

8

OsmaDrain

ODR



Cat no

Pack qty

Price £ per piece

Anti–Flood ValvesFor surface and foul water applicationsS/S Anti-Flood Valve 110 4D921 1 280.13– single valve 160 6D921 1 337.90

Sealed Inspection PipeS/S Inspection Pipe– with removable rectangular cover and airtight sealing ring, for use within traditional manholes or suspended drainage installations

a 110 4D420 1 181.62

Sealed Inspection Junction – 45ºS/S Equal Double Inspection Junction– with removable rectangular cover and airtight sealing ring, for use within traditional manholes or suspended drainage installations

a 110 4D492 1 236.89

Sealed Rodding EyesP/E Rodding Eye– square, sealed access cover, suitable 110 4D360 5 114.19for use in situations requiring a loading up to 15kN (1.5 tonnes), where the frame of the cover is supported by a concrete plinth

160 6D360 1 155.93

Use in conjunction with D/S Bend

S/S Square Top Rodding Point– sealed, c/w coupling 110 4D361 1 170.06

Screwed Access FittingsP/E Screwed Access Cover– allows full bore access to the drainage system for cleaning, fits into a standard OsmaDrain ring seal socket

a 110 4D292 5 34.69 a 160 6D292 1 79.34S/S Screwed Access Cover– allows full bore access to the drainage system for cleaning, fits over a standard OsmaDrain spigot

a 110 4D290 5 59.02 a 160 6D290 1 103.72

S/S Short Radius Access Bend – 87.5°– allows access via screwed access cover to the drainage system for cleaning

a 110 4D169 5 136.33

9


Cat no

Pack qty

Price £ per piece

S/S Access Pipe– allows access via screwed access cover to the drainage system for cleaning

a 110 4D274 5 98.83 a 160 6D274 1 212.94

D/S Short Radius Access Bend – 87.5°– allows access via screwed access cover to the drainage system for cleaning

a 110 4D569 5 148.55

D/S Equal Access Junction – 87.5°– allows access via screwed access cover to the drainage system for cleaning

a 110 4D593 5 172.35

Socket PlugsSocket Plug– internal blanking plug, fits into standard OsmaDrain spigot

110 4D291 10 16.23

P/E Socket (Closed) Plug– incorporates one closed boss socket position, will form either a 32mm, 40mm or 50mm waste pipe connection when fitted with the appropriate boss socket adaptor

a 110 4D296 5 24.47

P/E Socket Plug– allows full bore access to the drainage system for cleaning, fits into a standard OsmaDrain ring seal socket

160 6D296 1 52.47

a

P/E Socket (Open) Plug– incorporates one open boss socket position, will form either a 32mm, 40mm or 50mm waste pipe connection when fitted with the appropriate boss socket adaptor

a 110 4D297 10 37.35

Universal Gully FittingsS/S Universal Gully Trap– to obtain ‘P’, ‘Q’ or ‘S’ trap add appropriate 45º or 87.5° OsmaDrain bend $ 110 4D500 5 47.38

P/E Plain Hopper – with 150mm long spigot $ 110 4D507 2 52.06

P/E Vertical Inlet Hopper – with 150mm long spigot $ 110 4D508 1 63.68

10

OsmaDrain

ODR



Cat no

Pack qty

Price £ per piece

P/E Sealed Access Hopper – with 150mm long spigot $ 110 4D527 5 149.71

SW/S Plain Hopper– with solvent socket $ 110 4D503 5 35.55

SW/S Vertical Inlet Hopper – with solvent socket $ 110 4D504 1 61.09

S/S Bossed Pipe – with four boss sockets $ 110 4D589 5 35.68

Sealed Access Cover– for Universal Plain Hoppers complete with sealing ring and screws $ – 4D526 1 76.25

Bottle GulliesP/E Access Gully– square with rotating top and grid 110 4D850 1 85.40

S/S Paved Area Gully– polypropylene 110 4D860 1 127.32

Sealed Cover Plate – for use with 4D860 Paved Area Gully only

– 4D862 1 70.75

Metal Grid Gully Cover – for use with 4D860 Paved Area Gully only

– 4D863 1 83.76

S/S Bottle Gully – 87.5° – provides access to the drainage system for cleaning, supplied with all bosses closed

110 4D900 1 99.84

S/SW Bottle Gully – 87.5° – provides access to the drainage system for cleaning, supplied with side bosses closed but with 110mm back boss open

110 4D901 1 126.40

Sealed Access Cover– for 4D900/901 Bottle Gully – complete with sealing ring and screws

– 4D915 1 98.25

Bottle Gully Riser – 325mm long, for use with 4D900/901 Bottle Gully Range

160 4D916 1 18.01

– 160mm spigot connection

11


Cat no

Pack qty

Price £ per piece

DI Grating – for 4D900/901 Bottle Gully complete with screws – suitable for installations requiring a loading up to 35kN (3.5 tonnes), where the frame of the gully is supported by a concrete plinth

– 4D919 1 75.75

Yard Gully – 300mm diameterP/E Trapped Yard Gully – 600mm overall depth, supplied complete with removable rubber bung for rodding access $ 110 4D800 1 262.33

Grating and Frame – straight bar, hinged – suitable for use in installations requiring a BS EN124– B125 Medium Duty, loading up to 125kN (12.5 Tonnes) where the frame is supported in a concrete plinth

a – 4D810 1 335.10

Perforated Galvanised Mild Steel Catchment Bucket $ – 4D815 1 186.91

Suspended Bracketing System(Not suitable for damp inaccessible voids)Adjustable Pipe Bracket Assembly(pack contains threaded rod, threaded bracket, bracket plate and pipe/socket bracket)

110 4D086 1 69.33

Adjustable Socket Bracket and Brace Assembly(pack contains threaded rod, threaded bracket, bracket plate, two adjustable braces and pipe/socket bracket

110 4D085 1 142.70

Testing EquipmentStopper for Testing

110 4D998 1 63.86160 6D998 1 99.85

Cleaners, Solvent Cements, LubricantsDegreasing Cleaner No. 1– 250ml can – 4D380 10 18.64

Solvent Cement No. 2– 125ml can a – 4D383 10 21.61

12

OsmaDrain

ODR



Cat no

Pack qty

Price £ per piece

Soluble Lubricant– 0.5kg tub – 4D391 1 30.61

Soluble Lubricant– 2.5kg tub – 4D395 1 88.32

Spares – GeneralSnap Cap 110 4D116 1 7.39– 4D116 is combined cap and seal 160 6D116 1 6.37

Ring Seal 110 4D130 5 5.02160 6D130 5 9.62

Spares – Rodding EyesGasket – oval style – 4D317 5 11.42

Screws – new style (pack of 4) – 4D318 1 4.43

Spares – Screwed Access FittingsAccess Liner– for 4D593 – 4D902 1 23.53

Access Liner– for bend – 4D909 1 23.53

Screwed Access Cap – 4D904 1 19.26

Access Cap Gasket – 4D992 1 6.37

Spares – Universal GullyVertical Inlet Cover – 4D505 10 21.12

Gully Grating $ – 4D506 1 10.39

Spares – 4D900/4D901 Bottle GulliesGully Plug – 4D993 1 7.94

Gully Grating – 4D906 1 12.91

13


Cat no

Pack qty

Price £ per piece

Cover and Frame – 4D908 1 37.98

Spares – 4D850/4D860 GulliesRotating Top and Grid– spare – 4D851 1 30.36

Spare Top– c/w grid – 4D861 1 76.51

Spares – 4D420/4D492 Inspection JunctionsSealed Inspection Junction Plug – 4D494 10 27.00

Inspection Junction Washers(pack of 4) – 4D418 1 8.67

Inspection Junction Gasket – 4D421 5 16.59

Inspection Junction Cover – 4D930 1 52.21

Estimator’s GuidePrice per metre 110 – 21.45– based on one coupler per 6.0m length

160 – 47.59

14

Osma UltraRib

OUR

Foul and Surface Water drainage system 150-300mm


Cat no

Pack qty

Price £ per piece

PipeP/E Pipe3.0m $ WIS a 150 6UR073 36 57.123.0m $ WIS a 225 9UR073 16 166.053.0m $ WIS a 300 12UR073 9 256.77S/S Pipe3.0m $ WIS a 150 6UR043 36 69.893.0m $ WIS a 225 9UR043 16 180.953.0m $ WIS a 300 12UR043 9 271.33S/S Pipe6.0m $ WIS a 150 6UR046 36 139.786.0m $ WIS a 225 9UR046 16 361.90

Rocker PipeS/S Rocker Pipe– 600mm effective length$ a 150 6UR869 1 56.65$ a 225 9UR869 1 132.40$ a 300 12UR869 1 224.44CouplersD/S Slip Coupler– for new branch entry connections and repairs$ a 150 6UR105 1 45.75$ a 225 9UR105 1 107.54$ a 300 12UR105 1 214.40D/S Pipe Coupler– for jointing UltraRib pipe $ WIS a 150 6UR205 1 42.89 $ WIS a 225 9UR205 1 93.37 $ WIS a 300 12UR205 1 188.11AdaptorsD/S Adaptor– connector to BS EN 295 thinwall clay spigot $ 150 6UR129 1 113.19S/S Adaptor– 6UR socket x 160mm BS EN 1401 spigot $ 150 6UR141 1 91.71D/S Adaptor– 6UR socket x 160mm BS EN 1401 socket $ 150 6UR142 1 109.14S/S Adaptor– 6UR spigot x 160mm BS EN 1401 socket $ 150 6UR143 1 95.53

ReducersS/S Level Invert Reducer– to 110mm OsmaDrain spigot $ 150 6UR099 1 33.69

S/S Level Invert Reducer– to 150mm UltraRib spigot $ 225 9UR095 1 56.43

15


Cat no

Pack qty

Price £ per piece

D/S Level Invert Reducer– to 225mm UltraRib spigot $ 300 12UR093 1 183.14

Short Radius BendsS/S Bend – 45° $ 150 6UR163 1 68.92

D/S Bend – 87.5°– 6UR socket x 160mm BS EN 1401 socket $ 150 6UR560 1 133.64

D/S Bend – 87.5º $ 150 6UR561 1 77.15 $ 225 9UR561 1 324.15 $ 300 12UR561 1 510.59

D/S Bend – 45º $ 150 6UR563 1 57.37 $ 225 9UR563 1 241.31 $ 300 12UR563 1 438.22

D/S Bend – 30º $ 150 6UR566 1 57.37 $ 225 9UR566 1 255.59 $ 300 12UR566 1 425.37

D/S Bend – 15º $ 150 6UR567 1 57.37 $ 225 9UR567 1 249.23 $ 300 12UR567 1 405.01JunctionsEqual Junction – 87.5ºD/S Junction to UltraRib spigot $ 150 6UR193 1 138.71

Equal Junctions – 45°D/S Junction to UltraRib spigot $ 150 6UR213 1 138.71 $ 225 9UR213 1 481.19 $ 300 12UR213 1 1111.83

Unequal Junction – 87.5°D/S Junction to BS EN1401 spigot– 150 x 110mm $ 150 6UR199 1 131.77

Unequal Junctions – 45°– to BS EN1401 spigotD/S Junction – 150 x 110mm $ 150 6UR219 1 118.09D/S Junction – 225 x 110mm 225 9UR224 1 336.15D/S Junction – 225 x 160mm 225 9UR226 1 346.29D/S Junction – 300 x 160mm 300 12UR236 1 744.35

16

Osma UltraRib

OUR

Foul and Surface Water drainage system 150-300mm


Cat no

Pack qty

Price £ per piece

Unequal Junctions – 45°– to UltraRib spigotD/S Junction – 225 x 150mm $ 225 9UR227 1 346.29D/S Junction – 300 x 150mm $ 300 12UR237 1 687.08D/S Junction – 300 x 225mm $ 300 12UR240 1 1058.37

Screwed Access FittingsP/E Screwed Access Cover– allows full bore access to the sewerage system for cleaning, fits in to a standard UltraRib socket $ 150 6UR292 1 61.26

S/S Screwed Access Cover– allows full bore access to the sewerage system for cleaning, fits on to a standard UltraRib spigot $ 150 6UR290 1 77.32

Socket PlugsP/E Socket Plug– allows full bore access to the sewerage system for cleaning, fits in to a standard UltraRib socket $ 150 6UR296 1 22.79 $ 225 9UR296 1 111.96 $ 300 12UR296 1 149.19

Road GullyS/S Trapped Road Gully– 450mm diameter x 900mm deep $ 150 6UR600 1 217.34– 450mm diameter x 750mm deep $ 150 6UR590 1 262.67

LubricantSoluble Lubricant– 2.5kg tub – 6UR395 1 106.00

Soluble Lubricant– 5.0kg tub – 6UR396 1 175.63

Spares GeneralRing Seal 150 6UR117 5 6.77– UltraRib socket 225 9UR117 5 14.82

300 12UR117 1 27.73

Estimator’s GuidePrice per metre 150 – 23.30– based on S/S Pipe 3.0m length 225 – 60.32

300 – 90.44

17

Osma Shallow IC

ODR

Shallow Inspection Chambers


Cat no

Pack qty

Price £ per piece

Shallow Inspection Chamber (SIC)– 250mm diameter shaft for use with 110mm OsmaDrain to a maximum invert depth of 0.6 metres Osma Shallow Inspection Chamber is approved and Kitemarked to BS EN 7158:2001 and BS EN 13598-1:2010

Base OptionsD/S Equal Shallow Inspection Chamber– 110mm straight channel with one 110mm x 45° branch entry either side of the main channel, for use with 110mm OsmaDrain components.Supplied complete with 2 profiled, blank-off plugs for use in unused side entries

a 110 4D960 1 228.62

Cover and Frame OptionsRound Cover and Frame – A15 pedestrian – PVC-U– sealed, for use in situations requiring a loading up to 10kN (1.5 tonne) where the frame of the cover is supported by a concrete plinth.Can be used internally

a - 4D325 1 129.85Square Cover and Adjustable Frame – A15 pedestrian – PVC-U– sealed, for use in situations requiring a loading up to 10kN (1.5 tonne) where the frame of the cover is supported by a concrete plinthCan be used internally

a - 4D961 1 129.85

Spares Cover to Frame Seal– 250mm diameter for use with 4D325 and 4D961 covers and frames

- 4D314 5 14.27

Screws – 4D325/961– pack of 4 for use in securing 4D325/ 4D961 cover to its frame

- 4D318 1 4.43

Round Cover – PVC-U– 250mm diameter for use with 4D325 and 4D961 Frame

- 4D328 1 46.64

Blank-off Plugs– 110mm diameter for use 4D960 Inspection Chamber base

- 4D964 10 28.47

18

Osma Multi-Base IC

ODR

Multi-Base Inspection Chambers


Cat no

Pack qty

Price £ per piece

Multi-Base Shallow Inspection Chambers (MBIC)– 315mm dia shaft for use with 110mm OsmaDrain to a maximum invert depth of 0.6 metres(0.9m adopted areas only)Osma Multi-Base Shallow Inspection Chambers are approved and Kitemarked to BS EN 7158:2001 and BS EN 13598-1:2010 Base OptionsD/S Equal Inspection Chamber Base (WAJ 1)– 110mm straight channel for use with 110mm OsmaDrain components

a 110 4D910 1 115.91

D/S Equal Inspection Chamber Base (WAJ 3)– 110mm straight channel with one 110mm x 90° left hand branch entry for use with 110mm OsmaDrain components

a 110 4D911 1 118.64D/S Equal Inspection Chamber Base (WAJ 13)– 110mm straight channel with one 110mm x 90° right hand branch entry for use with 110mm OsmaDrain components

a 110 4D912 1 118.64

D/S Equal Inspection Chamber Base (WAJ 4)– 110mm straight channel with one 110mm x 45° left hand branch entry for use with 110mm OsmaDrain components

a 110 4D913 1 118.64D/S Equal Inspection Chamber Base (WAJ 12)– 110mm straight channel with one 110mm x 45° right hand branch entry for use with 110mm OsmaDrain components

a 110 4D914 1 118.64D/S Equal Inspection Chamber Base (WAJ 5)– 110mm straight channel with one 110mm x 45° branch entry either side of the main channel, for use with 110mm OsmaDrain components

a 110 4D917 1 119.23D/S Equal Inspection Chamber Base (WAJ 2)– 110mm bent 90° channel for use with 110mm OsmaDrain components

a 110 4D918 1 116.36

19


Cat no

Pack qty

Price £ per piece

D/S Equal Inspection Chamber Base (WAJ 16)– 110mm straight channel with one 110mm x 45° and one 110mm x 90° left hand branch entry, for use with 110mm OsmaDrain components

a 110 4D933 1 120.51D/S Equal Inspection Chamber Base (WAJ 7)– 110mm straight channel with one 110mm x 45° and one 110mm x 90° right hand branch entry, for use with 110mm OsmaDrain components

a 110 4D934 1 120.51D/S Equal Inspection Chamber Base (WAJ 18)– 110mm straight channel with two 110mm x 90° left/right hand branch entries, for use with 110mm OsmaDrain components

a 110 4D935 1 166.82

Shaft OptionsP/E Inspection Chamber Shaft– 315mm diameter x 150mm long for use with all types of multi-base 315mm basesSupplied with a pre-fitted elastomeric seal

a 315 4D937 1 95.85

Cover and Frame OptionsSquare Cover and Adjustable Frame – A15 pedestrian – PVC-U– for use in situations requiring a loading up to 15kN (1.5 tonne) where the frame of the cover is supported by a concrete plinthFor external use only

a - 4D969 1 151.41

Spares Shaft Seal– 315mm diameter for use with 4D937 shaft sections

- 4D957 1 7.84

Cover– spare cover for 4D969 - 4D970 1 50.25

Screws – 4D969– pack of 4 for use in securing 4D969 cover to its frame

- 4D971 1 6.30

20

Osma Universal IC

ODR

Universal Inspection Chambers


Cat no

Pack qty

Price £ per piece

Universal Inspection Chambers (UIC)– 450mm diameter shaft for use with 110mm or 160mm OsmaDrain or 150mm UltraRib to a maximum invert depth of 1.2 metresOsma Universal Inspection Chamber range is approved and Kitemarked to BS EN7158:2001 and BS EN 13598-1:2010

Base OptionsD/S Equal Inspection Chamber Base– 110mm straight channel with four 110mm (2 x 45° and 2 x 90°) left/right hand branch entries, for use with 110mm OsmaDrain componentsSupplied complete with 3 x 110mm blank-off plugs for use in unused side entries

a 110 4D922 1 330.48D/S Equal Inspection Chamber Base– 160mm straight channel with two 160mm x 90° left/right hand branch entries, for use with 160mm OsmaDrain componentsSupplied complete with 1 x 160mm blank-off plug for use in unused side entriesFor use with 160mm OsmaDrain components

a 160 6D928 1 361.65For use with 150mm UltraRib components

a 150 6UR928* 1 380.99

D/S UnEqual Inspection Chamber Base– 160mm straight channel with four 110mm (2 x 45° and 2 x 90°) left/right hand branch entries, for use with 110/160mm componentsSupplied with 3 x 110mm blank-off plug for use in unused side entriesFor use with 160mm OsmaDrain components


a 150 6UR929* 1 457.14

Shaft OptionsP/E Inspection Chamber Shaft– 450mm diameter x 305mm long for use with all types of Universal Inspection Chamber 450mm bases.Supplied with a pre-fitted elastomeric seal

a 450 4D975 1 111.75

* OUR discount applies

21


Cat no

Pack qty

Price £ per piece

Cover & Frame OptionsRound Cover & Frame – B125 - ductile iron– class BS EN 124-B125 medium duty, suitable for use in situations requiring a loading up to 125kN (12.5 tonnes), where the frame of the cover is supported by a concrete plinth

a - 4D942 1 287.08Square Cover and Frame – A15 – polypropylene– for use with the Osma 4D975 Inspecton Chamber Shaft in situations requiring a loading up to 15kN (1.5 tonnes)Comes complete with a 350mm restricted access for depths greater then 1.2 metresWhen surrounded by a concrete plinth the 4D920 can be used in situations with loadings up to 50kN (5 tonnes)

a - 4D920 1 220.56

Round Cover and Frame – A15 – polypropylene– for use with the Osma 4D975 Inspecton Chamber Shaft in situations requiring a loading up to 15kN (1.5 tonnes)Comes complete with a 350mm restricted access for depths greater then 1.2 metres

a - 4D924 1 185.44Round Cover and Frame – A15 – polypropylene– for use with the Osma 4D975 Inspecton Chamber Shaft in situations requiring a loading up to 15kN (1.5 tonnes)

a - 4D927 1 118.73Square Recessed Cover and Frame – steel cover, polypropylene frame– for use with the Osma 4D975 Inspecton Chamber Shaft in situations requiring a loading up to 25kN (2.5 tonnes), where the frame of the unit is supported by a concrete plinth

- 4D945 1 280.51

Square Recessed Cover and Frame – steel cover, polypropylene frame– sealed and suitable for internal use– for use with the Osma 4D975 Inspecton Chamber Shaft in situations requiring a loading up to 25kN (2.5 tonnes), where the frame of the cover is supported by a concrete plinth

- 4D946 1 347.20

Accessories Inspection Chamber Channel Cover– left hand, for use with 4D922 Inspection Chamber Base only to blank-off unused side entries

- 4D948 1 155.32

22

Osma Universal IC

ODR

Universal Inspection Chambers


Cat no

Pack qty

Price £ per piece

Inspection Chamber Channel Cover– right hand, for use with 4D922 Inspection Chamber Base only to blank-off unused side entries

- 4D949 1 155.32

Cover Sealing Ring– 450mm diameter, for sealing the cover of the 4D920/924/927 to its corresponding frame

- 4D994 1 20.52

Spares Inlet Blank-off Plugs– 110mm diameter for use with all 110mm chamber inlets

- 4D926 1 18.21

Screws - 4D920– pack of 4 for use in securing 4D920 cover to its frame

- 4D995 1 6.29

Screws - 4D927– pack of 4 for use in securing 4D927 cover to its frame

- 4D996 1 4.53

Eye Bolts - 4D920– pack of 3 for use in securing 4D920 frame to its shaft

- 4D997 1 2.96

23

Osma Non Man-Entry IC

ODR

Non Man-Entry Inspection Chambers


Cat no

Pack qty

Price £ per piece

Non Man-Entry Inspection Chamber (NIC)– 500mm diameter shaft for use with 110mm or 160mm OsmaDrain or 150mm UltraRib to a maximum invert depth of 3.0 metresOsma Non Man-Entry Inspection Chamber (NIC) range is approved and Kitemarked to BS EN7158:2001

Base OptionsD/S Equal Inspection Chamber Base– 110mm straight channel with two 110mm x 45° and two 110mm x 90° left/right hand branch entries, for use with 110mm OsmaDrain componentsSupplied complete with a base to shaft sealing ring and 3 x 110mm blank-off plugs for use in unused side entries

a 110 4D923 1 419.00D/S Equal Inspection Chamber Base– 160mm straight channel with two 160mm x 90° left/right hand branch entries, for use with 160mm OsmaDrain componentsSupplied complete with a base to shaft sealing ring and 1 blank-off plugs for use in unused side entriesFor use with 160mm OsmaDrain components


a 150 6UR936* 1 458.24

D/S UnEqual Inspection Chamber Base– 160mm straight channel with two 110mm x 45° and two 110mm x 90° left/right hand branch entries, for use with 110/160mm components. Supplied complete with a base to shaft sealing ring and 3 blank-off plugs for use in unused side entriesFor use with 160mm OsmaDrain components


a 150 6UR937* 1 426.21

* OUR discount applies

24

Osma Non Man-Entry IC

ODR

Non Man-Entry Inspection Chambers


Cat no

Pack qty

Price £ per piece

Shaft OptionsP/E Inspection Chamber Shaft– 500mm diameter for use with all types of NIC Chamber BasesInspection Chamber Shaft 1.5 metre length

a 500 6D934 1 469.67Inspection Chamber Shaft 3.0 metre length

a 500 6D938 1 818.77

Restriction Access Cap– for use with 6D934/6D938 shaft sections, restricts access to 350mm Requires 500TW117 seal

500 6D930 1 147.69

Shaft to Restriction Access Cap Seal– 500mm diameter for use with 6D930 Restriction Access Cap

- 500TW117= 1 68.85

Spares Chamber Base to Shaft Seal– 500mm diameter for use with 6D934/6D938 shaft sections

- 6D917 1 92.43

NIC Telescopic Adaptor – suitable for us with 4D920 and 4D945 covers and frames. Allows height adjustment and accommodation of slopes. Restricted to 350mm internal diameter

- 6D940 1 168.23

= TWI discount applies

25

Wavin Range 200 IC

WCH

Non Man-Entry Inspection Chambers: Range 200


Cat no

Pack qty

Price £ per piece

Non Man-Entry Inspection Chambers: Range 200– 200mm diameter shaft for use with 110mm or 160mm OsmaDrain or 150mm UltraRib (via adaptor) to a maximum invert depth of 2.0 metresWavin Chamber Range 200 is approved and Kitemarked to BS EN 13598-1:2010

Base OptionsD/S Equal Inspection Chamber Base– 110mm or 160mm straight channel for use with 110mm or 160mm OsmaDrain components

a 110 24NE300 1 190.02 a 160 26NE300 1 201.99For connection to 150mm UltraRib use adaptor 6UR141

150 6UR141* 1 91.71

Shaft OptionsP/E Inspection Chamber Shaft– 200mm diameter x 2.0 metres long for use with 24/26NE300 bases

a 200 20NE002 1 146.63

Cover and Frame OptionsSquare Cover and Frame - A15 - polypropylene– sealed, for use in situations requiring a loading up to 15kN (1.5 tonnes) where the frame of the cover is supported by a concrete plinth

a - 20NE015 1 155.93

Spares Screws - 20NE015– pack of 4 for use in securing 20NE015 cover to its frame

- 4D318l 1 pack

4.43

Spare Cover - polypropylene– for use with 20NE015 frame - 20NE203 1 70.75

* OUR discount applies, l ODR discount applies

26

Wavin Range 315 IC

WCH



Cat no

Pack qty

Price £ per piece

Non Man-Entry Inspection Chambers: Range 315– 300mm diameter shaft for use with 110mm or 160mm OsmaDrain or 150mm UltraRib (via adaptor) to a maximum invert depth of 2.0 metresWavin Inspection Chamber Range 315 is approved and Kitemarked to BS EN 13598-2:2009

Base OptionsD/S Equal Inspection Chamber Base– 110mm or 160mm straight channel for use with 110mm or 160mm OsmaDrain or 150mm UltraRib componentsSupplied complete with a base to shaft sealing ring


D/S Equal Inspection Chamber Base– 110mm or 160mm straight channel with one 110mm or 160mm x 45°, left hand branch entry, for use with 110mm or 160mm OsmaDrain or 150mm UltraRib componentsSupplied complete with a base to shaft sealing ring


D/S Equal Inspection Chamber Base– 110mm or 160mm straight channel with one 110mm or 160mm x 45°, right hand branch entry, for use with 110mm or 160mm OsmaDrain or 150mm UltraRib componentsSupplied complete with a base to shaft sealing ring


D/S Equal Inspection Chamber Base– 110mm or 160mm straight channel with one 110mm or 160mm x 45°, branch entry either side of the main channel, for use with 110mm or 160mm OsmaDrain or 150mm UltraRib componentsSupplied complete with a base to shaft sealing ring


27


Cat no

Pack qty

Price £ per piece

Shaft OptionsP/E Inspection Chamber Shaft– 300mm diameter x 2.0 metres long for use with all types of range 315 bases

a 315 30NE002 1 187.03

Cover and Frame OptionsSquare Cover and Frame – A15 – polypropylene– sealed, for use in situations requiring a loading up to 15kN (1.5 tonnes) where the frame of the cover is supported by a concrete plinth

a - 30NE015 1 216.96Spares Chamber Base to Shaft seal – 315mm diameter for use with 30NE002

- 30NE200 1 15.56

Cover and Frame Seal to Shaft – 315mm diameter for use with 30NE002

- 12TW117= 1 16.38

Screws – 30NE015– pack of 4 for use in securing 30NE015 cover to its frame

- 30NE205 1 5.05

Spare Cover – polypropylene– for use with 30NE015 frame - 30NE203 1 127.19


28

Wavin Range 450 IC

WCH



Cat no

Pack qty

Price £ per piece

Non Man-Entry Inspection Chambers: Range 450– 450mm diameter shaft for use with 110mm or 160mm OsmaDrain or 150mm UltraRib (via adaptor) to a maximum invert depth of 3.0 metresWavin Inspection Chamber Range 450 is approved and Kitemarked to BS EN 13598-2:2009

Base OptionsD/S Equal Inspection Chamber Base– 110mm or 160mm straight channel for use with 110mm or 160mm OsmaDrain or 150mm UltraRib components. Supplied complete with a base-to-shaft sealing ring


D/S Equal Inspection Chamber Base– 110mm straight channel with one 110mm x 45° and one 110mm x 90° left hand branch entry, for use with 110mm OsmaDrain components

Supplied complete with a base to shaft sealing ring and one 110mm blank-off plug for use in unused side entry

a 110 44NE304 1 480.07

D/S Equal Inspection Chamber Base– 110mm straight channel with one 110mm x 45° and one 110mm x 90° right hand branch entry, for use with 110mm OsmaDrain components


a 110 44NE305 1 480.07

D/S Equal Inspection Chamber Base– 110mm straight channel with two 110mm x 45° and two 110mm x 90° left/right hand branch entries, for use with 110mm OsmaDrain components

Supplied complete with a base to shaft sealing ring and three 110mm blank-off plugs for use in unused side entry

a 110 44NE306 1 495.91

29


Cat no

Pack qty

Price £ per piece

D/S Equal Inspection Chamber Base– 160mm straight channel with one 110mm x 45° and one 160mm x 90° left hand branch entry, for use with 110/160mm OsmaDrain or 150mm UltraRib components


a 160 46NE307 1 653.54For connection to 150mm UltraRib use adaptor 6UR141

D/S UnEqual Inspection Chamber Base– 160mm straight channel with one 110mm x 45° and one 160mm x 90° right hand branch entry, for use with 110/160mm OsmaDrain or 150mm UltraRib components



D/S UnEqual Inspection Chamber Base– 160mm straight channel with two 110mm x 45° and two 160mm x 90° left/right hand entries, for use with 110mm or 160mm OsmaDrain or 150mm UltraRib components

Supplied complete with a base to shaft sealing ring and two 110mm and one 160mm blank-off plugs for use in unused side entry


Shaft OptionsP/E Inspection Chamber Shaft– 450mm diameter x 3.0 metres long for use with all types of range 450 bases

a 450 40NE300 1 387.33

Restriction Access Cap– for use with 40NE300 shaft sections, restricts access to 350mm, supplied with one 450mm sealing ring

450 40NE930 1 226.21

30

Wavin Range 450 IC

WCH



Cat no

Pack qty

Price £ per piece

Cover and Frame OptionsRound Cover and Frame – A15– polypropylene– for use in situations requiring a loading up to 15kN (1.5 tonnes)

a - 4D927l 1 118.73

Spares Chamber Base to Shaft Seal – 450mm diameter for use with 40NE300

- 450TW117= 1 40.90

l ODR discount applies, = TWI discount applies

31

Wavin Range 600 IC

WCH



Cat no

Pack qty

Price £ per piece

Non Man-Entry Inspection Chambers: Range 600– 600mm diameter shaft for use with 150/225/300mm UltraRib or 150/225/300mm TwinWall (via adaptor) to a maximum invert depth of 3.0 metresWavin Inspection Chamber Range 600 is approved and Kitemarked to BS EN 13598-2:2009

Base OptionsD/S Equal Inspection Chamber Base– straight channel for use with 150/225/300mm UltraRib componentsSupplied complete with a base to shaft sealing ring and two UltraRib seals as appropriateFor use with 150mm UltraRib components

a $ 150 66NE300 1 1626.99For use with 225mm UltraRib components


a $ 300 612NE300 1 1693.42For connection to TwinWall use the appropriate S/S Adaptor i.e. 6TW145, 9TW145 or 12TW145

D/S Equal Inspection Chamber Base– bent 90° channel for use with 150/225/300mm UltraRib componentsSupplied complete with a base to shaft sealing ring and two UltraRib seals as appropriateFor use with 150mm UltraRib components




32

Wavin Range 600 IC

WCH

Non Man-entry Inspection Chambers: Range 600


Cat no

Pack qty

Price £ per piece

D/S Equal Inspection Chamber Base– bent 30° channel for use with 150/225/300mm UltraRib componentsSupplied complete with a base to shaft sealing ring and two UltraRib seals as appropriateFor use with 150mm UltraRib components




D/S Equal Inspection Chamber Base– straight channel, with two equal 90° left/right hand branch entries, for use with 150/225/300 UltraRib componentsSupplied complete with a base to shaft sealing ring and four UltraRib seals as appropriateFor use with 150mm UltraRib components




Shaft OptionsP/E Inspection Chamber Shaft– 600mm diameter x 3.0 metres long for use with all types of range 600 bases $ 600 60NE003 1 711.50

Restriction Access Cap– for use with 60NE003 shaft sections, restricts access to 350mm, supplied with one 600mm sealing ring

600 60NE930 1 183.60

Spares Chamber Base to Shaft Seal – 600mm diameter for use with 60NE003

- 600TW117= 1 100.12


33

Wavin IC Ancillaries

WCH

Inspection Chambers – Ancillaries


Cat no

Pack qty

Price £ per piece

Non Man-Entry Inspection Chambers– for connecting 110/160mm OsmaDrain pipe to IC Ranges 315, 450 and 600 shaft sections

Connector Kit 110 NE950 1 51.34

160 NE960 1 78.40

34

Osma Channels

OCH

Domestic Channel Drainage

Description Weightkg

Cat no

Pack qty

Price £ per piece

Domestic Channel DrainageOsmaChannel (polymer concrete) – 1.0m length – 78mm overall depth, complete with galvanised gratingC

6.70 100OC210 45 59.73

OsmaChannel Start and End Plate 0.03 100OC260 10 19.49

OsmaChannel End Outlet Connector – DN 110mm

0.07 100OC270 10 22.80

OsmaChannel Vertical Outlet Connector – DN 110mm

0.17 100OC280 1 35.52

OsmaChannel Sump Unit with Galvanised Grating and Bucket

13.30 100OC230 4 265.53

OsmaChannel Galvanised Grating – 1.0m length (Spare)

1.39 100OC211 1 17.89

RainChannel (Polypropylene) – 1.0m length – 87mm overall depth, black polypropylene channel, complete with black polypropylene snap-in grating

1.79 100OC410 49 48.45

RainChannel End Plate 0.03 100OC460 10 6.57

RainChannel Garage Pack – 3 x 1.0m channels and 2 end plates – in a handy carry home pack

5.43 100OC461 1 225.85

Threshold Drain Channel (PVC-U) – 1.2m length – Complete with grating

1.64 100OC510 5 76.95

Threshold Drain End Plate (Pair) 0.03 100OC560 1 14.90

Threshold Drain Outlet Adaptor 0.02 100OC520 1 21.77

Threshold Drain Jointing Piece 0.02 100OC530 1 9.56

35

Wavin Civils Channel

POL

Channels, gratings and accessories


Cat no

Pack qty

Price £ per piece

Medium Duty – 100mm wide C250Channel – flat, 150mm deep, 1.0m long

14.0 100MDC100 1 109.17

C

Slimslot CLIPFIX® grating 500mm long – ductile iron, C250

3.6 100MDC110 1 46.05

C

Slimslot CLIPFIX® grating 500mm long – composite, C250

1.1 100MDC120 1 52.30

C

End plate – blank 1.3 100MDC130 1 26.30

End plate – outlet 0.8 100MDC140 1 52.91

Sump – complete with bucket (does not include grating)

26.5 100MDC150 1 248.23

Heavy Duty – 100mm wide D400/F900Channel – flat, 150mm deep, 1.0m long

16.4 100HDC100 1 176.51

C

PROFIX® grating 500mm long – ductile iron, D400

3.8 100HDC110 1 58.47

C

PROFIX® grating 500mm long – ductile iron, F900

5.0 100HDC120 1 74.19

C

End plate – blank 1.3 100HDC130 1 39.02

End plate – outlet 1.1 100HDC140 1 65.59

Sump – complete with bucket (does not include grating)

33.2 100HDC150 1 388.30


26.8 150HDC100 1 235.63

C


6.5 150HDC110 1 93.92

C

36

Wavin Civils Channel

POL

Channels, gratings and accessories


Cat no

Pack qty

Price £ per piece


8.8 150HDC120 1 119.24

C



Sump upper – (does not include grating)

25.0 150HDC150 1 488.81

Sump lower 24.0 150HDC160 1 223.94

Sump bucket 3.1 150HDC170 1 172.02


35.4 200HDC100 1 271.05

C


7.9 200HDC110 1 130.96

C


12.3 200HDC120 1 167.99

C




25.1 200HDC150 1 877.86

Sump lower 24.0 200HDC160 1 317.31

Sump bucket 3.5 200HDC170 1 255.12


61.0 300HDC100 1 339.09

C


18.5 300HDC110 1 262.16

C

37


Cat no

Pack qty

Price £ per piece


24.6 300HDC120 1 305.12

C




33.8 300HDC150 1 1388.24

Sump lower 24.0 300HDC160 1 420.21

Sump bucket 4.5 300HDC170 1 351.28

Loading Class Application Guide

• Roadways • Industrial areas

• Special surfaces such as air traffic areasn

• Pedestrians • Cyclists • Green areas

• Passenger car parking lots and parking decks

• Delivery vans

• Trucks • Hard shoulder • Verge

D400 E600 F900

A15 B125 C250

38

Wavin TwinWall

TWI

Surface water drainage system 100-600mm


Cat no

Pack qty

Price £ per piece

Please Note:1. * Indicates non-stocked item, lead time available on request.2. Fitting prices are exclusive of ring seals, order separately if required.

PipeP/E Pipe3.0m unperforated$ 600 600TW073 2 688.05

P/E Pipe6.0m unperforated$ 100 4TW076 102 57.42$ 150 6TW076 33 74.22$ 225 9TW076 14 190.15$ 300 12TW076 8 295.76$ 375 375TW076 4 679.31$ 450 450TW076 4 913.53$ 500 500TW076 4 1042.22$ 600 600TW076 1 1342.53P/E Pipe6.0m perforated$ 100 4TW176 102 60.67$ 150 6TW176 33 78.55$ 225 9TW176 14 200.33$ 300 12TW176 8 320.14$ * 375 375TW086 4 773.66$ * 450 450TW086 4 952.85$ * 500 500TW086 2 1146.39$ * 600 600TW086 1 1513.20P/E Pipe6.0m half perforated $ 150 6TW276 33 78.56$ 225 9TW276 14 200.33$ 300 12TW276 8 320.14$ * 375 375TW096 4 773.66$ * 450 450TW096 4 952.85$ * 500 500TW096 2 1146.39$ * 600 600TW096 1 1513.20

S/S Pipe6.0m unperforated $ 375 375TW046 4 713.07$ 450 450TW046 4 997.72$ 500 500TW046 4 1176.26$ 600 600TW046 1 1520.13S/S Pipe6.0m perforated $ * 375 375TW066 4 807.20$ * 450 450TW066 4 1037.32$ * 500 500TW066 4 1233.60$ * 600 600TW066 1 1623.09S/S Pipe6.0m half perforated $ * 375 375TW056 4 807.20$ * 450 450TW056 4 1037.32$ * 500 500TW056 4 1233.60$ * 600 600TW056 1 1623.09

39


Cat no

Pack qty

Price £ per piece

CouplersD/S Pipe Coupler– for joining TwinWall Pipe$ 100 4TW205 1 8.44$ 150 6TW205 10 9.53$ 225 9TW205 8 16.88$ 300 12TW205 3 27.78$ 375 375TW205 1 84.12$ 450 450TW205 1 104.02$ 500 500TW205 1 160.72$ 600 600TW205 1 211.94

AdaptorsD/S Adaptor– connector to BS EN 295 thinwall clay spigot $ 150 6TW129 1 113.07S/S Adaptor– 6TW socket x 160mm BS EN 1401 spigot $ 150 6TW141 1 31.28

D/S Adaptor– 6TW socket x 160mm BS EN 1401 socket $ 150 6TW142 1 31.28

S/S Adaptor– 6UR spigot x 6TW socket $ 150 6TW145 1 42.05S/S Adaptor– 9UR spigot x 9TW socket $ 225 9TW145 1 109.12S/S Adaptor– 12UR spigot x 12TW socket $ 300 12TW145 1 152.36

ReducersD/S Level Invert Reducer– 6TW socket x 4TW socket $ 150 6TW097 1 60.87

S/S Level Invert Reducer– 6TW spigot x 110mm BS EN 1401 socket, includes seal $ 150 6TW099S 1 64.79S/S Level Invert Reducer– 9TW spigot x 6TW socket, includes seal $ 225 9TW095S 1 84.43S/S Level Invert Reducer– 12TW spigot x 9TW socket, includes seal $ 300 12TW093S 1 126.07S/S Level Invert Reducer– 375TW spigot x 12TW socket $ 375 375TW099 1 326.08S/S Level Invert Reducer– 450TW spigot x 375TW socket $ 450 450TW099 1 492.91

40

Wavin TwinWall

TWI



Cat no

Pack qty

Price £ per piece

S/S Level Invert Reducer– 500TW spigot x 450TW socket $ 500 500TW099 1 670.81S/S Level Invert Reducer– 600TW spigot x 500TW socket $ 600 600TW099 1 682.50

Short Radius BendsD/S Bend– 87.5º$ 150 6TW561 1 56.29$ 225 9TW561 1 181.15$ 300 12TW561 1 310.53$ 375 375TW561 1 657.20$ 450 450TW561 1 784.52$ 500 500TW561 1 1076.17$ 600 600TW561 1 1240.46

D/S Bend– 45º $ 150 6TW563 1 56.29$ 225 9TW563 1 181.15$ 300 12TW563 1 310.53$ 375 375TW563 1 657.20$ 450 450TW563 1 784.52$ 500 500TW563 1 1076.17$ 600 600TW563 1 1240.46



Equal Junction – 45°D/S Junction to TwinWall spigot$ 150 6TW213 1 92.96$ 225 9TW213 1 362.32$ 300 12TW213 1 1034.97$ 375 375TW375x45 1 1679.60$ 450 450TW450x45 1 1971.57$ 500 500TW500x45 1 2793.05$ 600 600TW600x45 1 3039.44

41


Cat no

Pack qty

Price £ per piece

Equal Junction – 90°D/S Junction to TwinWall spigot$ 150 6TW193 1 102.52$ 225 9TW193 1 341.28$ 300 12TW193 1 919.69

S/S Junction to TwinWall spigot$ * 375 375TW375x90 1 1518.95$ * 450 450TW450x90 1 1971.57$ * 500 500TW500x90 1 2793.05$ * 600 600TW600x90 1 3039.46

Unequal Junction – 45° D/S Junction to TwinWall spigot– 225mm x 150mm $ 225 9TW227 1 238.13– 300mm x 150mm $ 300 12TW237 1 353.84– 300mm x 225mm $ 300 12TW240 1 631.33– 375mm x 150mm $ 375 375TW150x45 1 506.89– 450mm x 150mm $ 450 450TW150x45 1 549.81– 500mm x 150mm $ * 500 500TW150x45 1 739.35– 600mm x 150mm $ 600 600TW150x45 1 796.29

S/S Junction to TwinWall spigot – 45° – 375mm x 225mm $ * 375 375TW225x45 1 759.89– 375mm x 300mm $ * 375 375TW300x45 1 1224.01– 450mm x 225mm $ * 450 450TW225x45 1 985.74– 450mm x 300mm $ * 450 450TW300x45 1 1067.96– 450mm x 375mm $ * 450 450TW375x45 1 1971.57– 500mm x 225mm $ * 500 500TW225x45 1 1109.02– 500mm x 300mm $ * 500 500TW300x45 1 1211.71– 500mm x 375mm $ * 500 500TW375x45 1 2751.95– 500mm x 450mm $ * 500 500TW450x45 1 2751.95

42

Wavin TwinWall

TWI



Cat no

Pack qty

Price £ per piece

S/S Junction to TwinWall spigot – 45° – 600mm x 225mm $ * 600 600TW225x45 1 1271.72– 600mm x 300mm $ * 600 600TW300x45 1 3039.44– 600mm x 375mm $ * 600 600TW375x45 1 3039.44– 600mm x 450mm $ * 600 600TW450x45 1 3039.44– 600mm x 500mm $ * 600 600TW500x45 1 3039.44

Unequal Junction – 90°S/S Junction to TwinWall spigot– 375mm x 150mm $ * 375 375TW150x90 1 560.50– 375mm x 225mm $ * 375 375TW225x90 1 759.89– 450mm x 150mm $ * 450 450TW150x90 1 607.95– 450mm x 225mm $ * 450 450TW225x90 1 985.74– 500mm x 150mm $ * 500 500TW150x90 1 758.30– 600mm x 150mm $ * 600 600TW150x90 1 880.52

End CapsFor TwinWall spigot 150 6TW750 1 28.84

225 9TW750 1 54.54300 12TW750 1 67.18375 375TW750 1 82.18450 450TW750 1 113.59500 500TW750 1 143.13600 600TW750 1 165.80

Ring SealTwinWall socket$ 100 4TW117 1 3.83$ 150 6TW217 1 3.67$ 225 9TW217 1 8.86$ 300 12TW217 1 16.38$ 375 375TW117 1 36.13$ 450 450TW117 1 40.90$ 500 500TW117 1 68.85$ 600 600TW117 1 100.12

Road GulliesP/E Road Gully– 450mm diameter x 900mm deep $ 150 6TW650 1 118.54– 450mm diameter x 750mm deep $ 150 6TW651 1 107.20

43


Cat no

Pack qty

Price £ per piece

SparesRing Seal – for old style TwinWall pipe$ 150 6TW117 1 3.67$ 225 9TW117 1 8.86$ 300 12TW117 1 16.38

Estimator’s GuidePrice per metre– based on P/E Pipe 6.0m 100 – 12.25unperforated, 1 coupler and 2 ring 150 – 15.18seals 225 – 37.46

300 – 59.38

– based on S/S Pipe 375 – 124.87unperforated and 1 ring seal 450 – 159.07

500 – 207.52600 – 270.04

– based on P/E Pipe 6.0m 100 – 11.52perforated/half perforated 150 – 14.68pipe and 1 coupler 225 – 36.2

300 – 57.99

– based on S/S perforated/ 375 – 134.53half perforated pipe 450 – 172.89

500 – 205.6600 – 270.52

44

WavinCoil

LDR

Land Drainage 80-160mm


Cat no

Pack qty

Price £ per piece

Corrugated Coiled Pipe – PerforatedS/S Coil – 100m

a 80 80D100 1 282.32S/S Coil – 50m

a 80 80D050 1 166.70S/S Coil – 25m

a 80 80D025 1 89.74S/S Coil – 100m

a 100 100D100 1 454.41S/S Coil – 50m

a 100 100D050 1 276.27S/S Coil – 25m

a 100 100D025 1 146.22S/S Coil – 50m

a 160 160D050 1 503.84S/S Coil – 25m

a 160 160D025 1 408.69

End CapS/S End Cap

a 80 80D297 1 5.19 a 100 100D297 1 5.90

CouplersD/S Pipe Coupler

a 80 80D104 1 4.45 a 100 100D104 1 4.94 a 160 160D104 1 6.65

Equal Junctions – 67.5°D/S Junction

a 80 80D200 1 12.64 a 100 100D200 1 14.12

Unequal Junction – 67.5°D/S Junction – 100mm x 80mm

a 100 100D208 1 13.47

Equal Junctions – 67.5°D/S Multi junction – with reducing bush to 80mm or 100mm pipe

a 100 100D215 1 10.24 a 160 160D215 1 33.63

45

Wavin MDPE

UTL

Potable water pressure pipe system 20-63mm


Cat no

Pack qty

Price £ per piece

20mm to 63mm MDPE PipeCoil - 25m

a 20 20PW025 9 35.30 a 25 25PW025 10 47.41 a 32 32PW025 8 75.50 a 50 50PW025 1 182.06 a 63 63PW025 1 277.50

Coil - 50m a 20 20PW050 9 70.59 a 25 25PW050 7 94.78 a 32 32PW050 8 151.01 a 50 50PW050 1 364.10 a 63 63PW050 1 554.99

Coil - 100m a 20 20PW100 9 141.20 a 25 25PW100 7 189.57 a 32 32PW100 4 302.01 a 50 50PW100 1 728.23 a 63 63PW100 1 1109.98Coil - 150m

a 25 25PW150 1 284.35 a 32 32PW150 1 453.01 a 50 50PW150 1 1092.33 a 63 63PW150 1 1664.96

46

Wavin Trigon

TRI

Barrier pressure pipe potable water system 25-63mm


Cat no

Pack qty

Price £ per piece

PE Barrier PipeCoil – 50m – WIS 25 71021050 5 1027.17 – WIS 32 71031050 1 1324.75

FittingsStraight Couplings – WIS 25 71902500 10 44.15 – WIS 32 71903500 10 63.74

Reducer32mm x 25mm – WIS 32 71903225 1 110.9350mm x 32mm – WIS 50 71905232 1 113.3763mm x 50mm

Transition Coupling to Copper25mm x 15mm – WIS 25 71902515 10 69.8125mm x 22mm – WIS 25 71902522 10 81.28

Transition Coupling to PE25mm x 25mm – WIS 25 71902525 10 38.1363mm x 63mm

Male Couplings25mm x ¾” – WIS 25 71902570 1 21.9732mm x 1” – WIS 32 71903570 10 34.9563mm x 2”

Female Couplings25mm x ¾” – WIS 25 71902580 10 21.9732mm x 1” – WIS 32 71903580 10 34.9563mm x 2”

Equal Tee – WIS 25 71902700 5 117.66 – WIS 32 71903700 1 181.53

Reduced Tee32mm x 25mm x 32mm – WIS 32 71903725 1 67.1663mm x 32mm x 63mm

Elbow – 90° – WIS 25 71902590 10 65.75 – WIS 32 71903590 5 136.38

Gate Valve – WIS 25 71902400 1 323.85 – WIS 32 71903400 1 404.80

47


Cat no

Pack qty

Price £ per piece

SparesSeal – Spare – WIS 25 71902460 1 3.04 – WIS 32 71903460 1 6.10

Blanking Plug – WIS 25 71902410 1 8.08 – WIS 32 71903410 1 12.16

Support Inserts – WIS 25 71902420 1 2.04 – WIS 32 71903420 1 3.04

48

Introduction to

Wavin’s specialist approach to responsible management of stormwater, including its efficient capture, transportation, cleansing, infiltration and attenuation and re-use. We’re ready to contribute at any stage in a project, with one central goal: to help achieve the optimum project outcome. Our in-depth expertise, design insight and proven system technology is applied wherever required to ensure each installed scheme achieves maximum efficiency of cost and integrated function, and full compliance to the latest regulatory criteria.

B Black

Gn Green

G Grey

W White

Email: [email protected] Web: www.wavin.co.uk

! British Standards Kitemark

Identifies pipe and fittings manufactured under the B.S.I. Certification Scheme.

$ British Board of Agrément

BBA Logo Identifies non-Kitemarked fittings covered by a British Board of Agrément Certificate.

a) British Board of Agrément

$ AquaCell Eco, Prime, Core and Plus have been awarded British Board of Agrément approval under BBA Agrément Certificate No.03/4018.

Key to abbreviations

Symbols

Acceptance

Wavin Stormwater Management systems

Introduction to Wavin Stormwater Management Systems

49

Wavin AquaGrid

INT

Plastic Pervious Paving system


Cat no

Pack qty

Price £ per piece

Plastic Pervious PavingAquaGrid 50 - 0AG550 92 15.50– 500mm x 500mm x 50mm, supplied complete with three pins

AquaGrid 75 - 0AG575 60 21.69– 500mm x 500mm x 75mm, supplied complete with three pins

Ancillary ItemsAquaGrid Pins - for use with both 50mm and 75mm units

- 0AG502 90 1.26

AquaGrid Demarcation Block – 50mm– for identification of car parking areas, for use with the 50mm deep systems

50 0AG504 1 6.21

AquaGrid Demarcation Block – 75mm– for identification of car parking areas, for use with the 75mm deep systems

75 0AG505 1 6.21

50

Wavin Vortex ValvesVortex Flow Control Valves


Cat no

Pack qty

Price £ per piece

Vortex Flow Control Valves – for the management of stormwater discharge

Tornado – Vortex Flow Control Valves *

– – – POA

– comes complete with an integral pivoting bypass door and stainless steel wire rope, facilitating emergency drain-down from ground level. Spigot or plate fixing options available.

Hurricane – Vortex Flow Control Valves *

– – – POA

– comes complete with lifting handle, which enables easy and convenient de-mounting/mounting of the valve from ground level. Spigot or plate fixing options available.

Typhoon – Vortex Flow Control Valves *

– – – POA

– comes complete with integral drain-down facility via a removable up-stand pipe from ground level. Spigot or plate fixing options available.

* The vortex valves are bespoke and custom built for any required discharge rate, contact Technical Design for more information.

51

Wavin AquaCell

AQA

AquaCell system


Cat no

Pack qty

Price £ per piece

AquaCell Modular UnitsAquaCell Eco (for landscaped/ non-trafficked sites)– for soakaway and storage applications - 1.0m x 0.5m x 0.4m 100% recycled polypropylene modular unit - 95% voidSupplied complete with three clips and two shear connectors (BBA No. 03/4018) $ 160 6LB025 15# 105.55

AquaCell Core-R (for both regular and heavy traffic loadings) – for soakaway and storage applications – 1.0m x 0.5m x 0.4m modular unit – 95% voidSupplied complete with three clips and two shear connectors $ 160 6LB150 15# 169.47AquaCell Plus-R (for deep and/or inspectable applications in landscaped and regular/heavily trafficked areas) – for soakaway and storage applications where inspectability is required – 1.0m x 0.5m x 0.4m modular unit – 95% void.Supplied complete with three clips, two shear connectors and one end cap $ 160 6LB250 15# 193.74

Silt TrapsSilt Trap500mm diameter x 1.25m depth– with 160mm OsmaDrain inlet 6LB600 1◊ 912.16– with 225mm TwinWall inlet 6LB622 1◊ 912.16– with 300mm TwinWall inlet 6LB630 1◊ 912.16

Domestic Silt Trap - for non loaded applications– 250mm diameter x 750mm depth 6LB300 1 216.71– with 110mm diameter inlet and outlet spigots (for use with the 4D961 cover and frame)

Extension Piece for 6LB300– 250mm diameter x 500mm depth (effective length = 335mm)

6LB301 1 120.35

Silt Trap Bucket for 6LB300– 200mm x 210mm depth 6LB302 1 129.02

◊ Non-stock item, lead time and terms and conditions available on request.# Site deliveries are 15 pieces. Merchant deliveries are 12 pieces.

52

Wavin AquaCell

AQA

AquaCell system


Cat no

Pack qty

Price £ per piece

Ancillary ItemsS/S Adaptor – 6UR socket x 160mm BS EN 1401 spigot for connection of UltraRib to infiltration unit

150 6UR141* 1 91.71

S/S Level Invert Reducer – to 110mm pipe 150 6UR099* 1 33.69

S/S Adaptor – 6TW socket x 160mm BS EN 1401 spigot

150 6TW141= 1 31.28

S/S Level Invert Reducer – to 110mm OsmaDrain 160 6D099l 1 64.41

PE Adaptor – 160mm spigot connection 150 4D916l 1 18.01

Flange Adaptor (150mm) – 6UR socket for connection of UltraRib to infiltration unit at positions other than preformed opening

150 6LB104 1 107.48

Flange Adaptor (225mm) – 9UR socket for connection of UltraRib to infiltration unit

225 6LB106 1 174.40

AquaCell Clip (spare) – for joining units 6LB105 1 2.14

AquaCell Shear Connector (spare) – for joining in multi-layer installations 6LB102 1 1.60

AquaCell Plus-R End Cap (spare)– for blocking off unused inlets/outlets 6LB202 1 3.34

l ODR discount applies, * OUR discount applies, = TWI discount applies

53

Wavin Q-Bic Plus

QBP

Inspectable & cleanable infiltration/attenuation system


Cat no

Pack qty

Price £ per piece

Q-Bic Plus SystemQ-Bic Plus Column UnitStructural component of Q-Bic Plus system

3059730 1 128.17

Q-Bic Plus Solid Base PlateSolid base plate for use in attenuation applications

3059731 1 42.08

Q-Bic Plus Perforated Base PlatePerforated base plate for use in infiltration applications

3059732 1 36.85

Q-Bic Plus Side Plate 3059733 1 30.68For use on external walls of Q-Bic Plus structure

Connection optionsQ-Bic Plus Connection Plate – 160mmFor use with 160mm pipe 160 3059735 1 24.67

Q-Bic Plus Connection Plate – 315mmFor use with 4062303, 4062358, 4062356, 4062357, 4066677 flange adaptors

315 3059736 1 22.72

Q-Bic Plus Side Flange Adaptor – 225mm UltraRibFor connecting 225mm UltraRib pipe. Can be used with 9TW145 for connections to 225mm TwinWall. Requires 3059736

4062303 1 72.14

Q-Bic Plus Side Flange Adaptor – 300mm TwinWallFor connections to 300mm TwinWall.Requires 3059736

4062358 1 72.14


4062356 1 72.14


4066677 1 67.58

Q-Bic Plus Side Flange Adaptor – 300mm UltraRibFor connections to 300mm UltraRib.Requires 3059736

4062357 1 72.14

Vertical Access OptionsQ-Bic Plus Vertical Shaft Adaptor – 300mmFor connection to 300mm vertical access shaft – 30NE002

4062305 1 72.14

54

Wavin Q-Bic Plus

QBP

Inspectable & cleanable infiltration/attenuation system


Cat no

Pack qty

Price £ per piece

Q-BicPlus Vertical Shaft Adaptor – 500mmFor connection to 500mm vertical access shaft – 6D934

4062304 1 72.14

Shaft OptionsP/E Inspection Shaft– 300mm diameter shaft 2 metre length

300 30NE002* 1 187.03

Ring SealFor sealing 300mm shaft (30NE002) to Q-Bic Plus Vertical Shaft Adaptor 300mm

300 12TW117* 1 16.38

P/E Inspection Shaft– 500mm diameter shaft 1.5 metre length

500 6D934• 1 469.67

Restriction Access CapFor use with 6D934 shaft, restricts access to 350mm

500 6D930• 1 147.69

Ring SealFor sealing 500mm shaft (6D934) to Q-Bic Plus Vertical Shaft Adaptor 500mm and 6D930 Cover and Frame

– 500TW117* 1 68.85

Cover and Frame OptionsSquare Cover and Frame – A15 – Polypropylene– sealed, for use in situations requiring a loading up to 15kN (1.5 tonnes) where the frame of the cover is supported by a concrete plinth

– 30NE015* 1 216.96

l ODR discount applies, * WCH discount applies

55

Wavin Garastor

INT

Garastor system


Cat no

Pack qty

Price £ per piece

Garastor Storm and Surface Water Control ChamberGarastorStorm and surface water control chamber– 500mm diameter x 1.0m deep unit 6SC500 1◊ 1620.51– 500mm diameter x 1.25m deep unit

6SC501 1◊ 1775.34

Ancillary ItemsGarastor Extension Kit 6SC205 1 347.51– 500mm diameter TwinWall coupler and two ring seals, shaft of TwinWall pipe also requiredGarastor Connection Kit 6SC200 1 74.61– Section of 150mm TwinWall pipe (220mm in length) and two ring seals

◊ Non-stock item, lead time and terms and conditions available on request.

56

PG11

Wavin Temporary Manhole CoverTemporary Manhole Cover

Description Nom Dia mm

Cat No

PackQty

Price Each £

Temporary Manhole CoverTo fit 600 x 600mm and 675 x 675mm square openings

600 TMC1 3 169.54

57

PG15

Osma GeotextileGeotextile products

Description Tensile stength

Roll size Cat no

Packqty

Price £ per piece

Standard Product RangeNonwoven 4.5m Roll 6x6

kN/m4.5x100 KNW6/6 1 367.37

Nonwoven 4.5m Roll 8.3x8.3 kN/m

4.5x100 KNW8 1 448.45

Woven 4.5m Roll 18x14 kN/m

4.5x100 KSG18/9 1 407.91

Woven Handy Pack 17x10 kN/m

50m2 KSG18/9HP 1 84.92

Nonwoven – FiltrationWhen used as a filtration layer, it will hold back soil particles from entering underground structures, such as AquaCell soakaways, and allow the free flow of water from them.

Woven – SeparationWhen used as a separation layer it prevents the intermixing of particles from two sub-surface layers with different properties, such as sub-soil and hardcore in driveways and roads.

58

Catno

Price £ per piece

Page no

Catno

Price £ per piece

Page no

Catno

Price £ per piece

Page no

Numerical index

0AG502 1.26 49 0AG504 6.21 49 0AG505 6.21 49 0AG550 15.50 49 0AG575 21.69 49 4D066 168.04 44D073 53.83 4 4D076 107.66 4 4D085 142.70 11 4D086 69.33 11 4D095 44.34 5 4D104 21.01 4 4D105 32.32 4 4D115 57.27 4 4D116 7.39 12 4D127 72.44 4 4D129 57.39 4 4D130 5.02 12 4D131 128.73 4 4D149 15.21 4 4D159 16.20 5 4D161 47.19 5 4D162 51.06 5 4D163 47.19 5 4D166 45.46 5 4D167 45.46 5 4D168 45.46 5 4D169 136.33 8 4D173 57.29 6 4D181 206.12 6 4D183 105.81 6 4D190 66.64 7 4D193 75.32 7 4D205 19.58 4 4D210 69.55 7 4D213 78.22 7 4D274 98.83 9 4D281 104.69 6 4D283 89.69 6 4D286 18.19 5 4D287 16.23 5 4D288 16.23 5 4D290 59.02 8 4D291 16.23 9 4D292 34.69 8 4D295 5.72 5 4D296 24.47 9 4D297 37.35 9 4D298 17.17 5 4D299 19.77 5 4D314 14.27 17 4D317 11.42 12 4D318 4.43 12 4D318 4.43 17 4D318l 4.43 25 4D325 129.85 17

4D328 46.64 17 4D360 114.19 8 4D361 170.06 8 4D380 18.64 11 4D383 21.61 11 4D391 30.61 12 4D395 88.32 12 4D418 8.67 13 4D420 181.62 8 4D421 16.59 13 4D464 51.77 5 4D492 236.89 8 4D494 27.00 13 4D500 47.38 9 4D503 35.55 10 4D504 61.09 10 4D505 21.12 12 4D506 10.39 12 4D507 52.06 9 4D508 63.68 9 4D526 76.25 10 4D527 149.71 10 4D561 55.87 6 4D562 60.44 6 4D563 55.87 6 4D566 54.09 6 4D567 54.09 6 4D568 54.09 6 4D569 148.55 9 4D573 66.84 6 4D581 90.45 7 4D583 118.00 7 4D589 35.68 10 4D593 172.35 9 4D800 262.33 11 4D810 335.10 11 4D815 186.91 11 4D850 85.40 10 4D851 30.36 13 4D860 127.32 10 4D861 76.51 13 4D862 70.75 10 4D863 83.76 10 4D900 99.84 10 4D901 126.40 10 4D902 23.53 12 4D904 19.26 12 4D906 12.91 12 4D908 37.98 13 4D909 23.53 12 4D910 115.91 18 4D911 118.64 18 4D912 118.64 18 4D913 118.64 18 4D914 118.64 18 4D915 98.25 10

4D916 18.01 10 4D916l 18.01 52 4D917 119.23 18 4D918 116.36 18 4D919 75.75 11 4D920 220.56 21 4D921 280.13 8 4D922 330.48 20 4D923 419.00 23 4D924 185.44 21 4D926 18.21 22 4D927 118.73 21 4D927l 118.73 30 4D930 52.21 13 4D933 120.51 19 4D934 120.51 19 4D935 166.82 19 4D937 95.85 19 4D942 287.08 21 4D945 280.51 21 4D946 347.20 21 4D948 155.32 21 4D949 155.32 22 4D957 7.84 19 4D960 228.62 17 4D961 129.85 17 4D964 28.47 17 4D969 151.41 19 4D970 50.25 19 4D971 6.30 19 4D975 111.75 20 4D992 6.37 12 4D993 7.94 12 4D994 20.52 22 4D995 6.29 22 4D996 4.53 22 4D997 2.96 22 4D998 63.86 11 4TW076 57.42 38 4TW117 3.83 42 4TW176 60.67 38 4TW205 8.44 39 6D066 341.79 4 6D073 123.48 4 6D076 246.99 4 6D099 64.41 5 6D099l 64.41 52 6D104 38.55 4 6D105 78.50 4 6D116 6.37 12 6D127 157.40 4 6D129 138.85 4 6D130 9.62 12 6D161 120.46 5 6D163 120.46 5 6D166 106.76 5

59

Catno

Price £ per piece

Page no

Catno

Price £ per piece

Page no

Catno

Price £ per piece

Page no

6D167 106.76 5 6D190 217.52 7 6D193 240.38 7 6D198 167.67 7 6D199 185.29 7 6D205 39.23 4 6D210 198.79 7 6D213 219.68 7 6D218 171.21 7 6D219 189.19 7 6D274 212.94 9 6D281 283.09 6 6D283 174.09 6 6D290 103.72 8 6D292 79.34 8 6D296 52.47 9 6D360 155.93 8 6D561 133.10 6 6D563 133.10 6 6D566 117.96 6 6D567 117.96 6 6D917 92.43 24 6D921 337.90 8 6D928 361.65 20 6D929 392.02 20 6D930 147.69 24 6D930• 147.69 54 6D934 469.67 24 6D934• 469.67 54 6D936 418.62 23 6D937 418.63 23 6D938 818.77 24 6D940 168.23 24 6D998 99.85 11 6LB025 105.55 51 6LB102 1.60 52 6LB104 107.48 52 6LB105 2.14 52 6LB106 174.40 52 6LB150 169.47 51 6LB202 3.34 52 6LB250 193.74 51 6LB300 216.71 51 6LB301 120.35 51 6LB302 129.02 51 6LB600 912.16 51 6LB622 912.16 51 6LB630 912.16 51 6SC200 74.61 55 6SC205 347.51 55 6SC500 1620.51 55 6SC501 1775.34 55 6TW076 74.22 38 6TW097 60.87 39 6TW099S 64.79 39 6TW117 3.67 43

6TW129 113.07 39 6TW141 31.28 39 6TW141= 31.28 52 6TW142 31.28 39 6TW145 42.05 39 6TW176 78.55 38 6TW193 102.52 41 6TW205 9.53 39 6TW213 92.96 40 6TW217 3.67 42 6TW276 78.56 38 6TW561 56.29 40 6TW563 56.29 40 6TW566 56.29 40 6TW567 56.29 40 6TW650 118.54 42 6TW651 107.20 42 6TW750 28.84 42 6UR043 69.89 14 6UR046 139.78 14 6UR073 57.12 14 6UR099 33.69 14 6UR099* 33.69 52 6UR105 45.75 14 6UR117 6.77 16 6UR129 113.19 14 6UR141 91.71 14 6UR141* 91.71 25 6UR141* 91.71 52 6UR142 109.14 14 6UR143 95.53 14 6UR163 68.92 15 6UR193 138.71 15 6UR199 131.77 15 6UR205 42.89 14 6UR213 138.71 15 6UR219 118.09 15 6UR290 77.32 16 6UR292 61.26 16 6UR296 22.79 16 6UR395 106.00 16 6UR396 175.63 16 6UR560 133.64 15 6UR561 77.15 15 6UR563 57.37 15 6UR566 57.37 15 6UR567 57.37 15 6UR590 262.67 16 6UR600 217.34 16 6UR869 56.65 14 6UR928* 380.99 20 6UR929* 457.14 20 6UR936* 458.24 23 6UR937* 426.21 23 9TW076 190.15 38 9TW095S 84.43 39

9TW117 8.86 43 9TW145 109.12 39 9TW176 200.33 38 9TW193 341.28 41 9TW205 16.88 39 9TW213 362.32 40 9TW217 8.86 42 9TW227 238.13 41 9TW276 200.33 38 9TW561 181.15 40 9TW563 181.15 40 9TW566 181.15 40 9TW567 181.15 40 9TW750 54.54 42 9UR043 180.95 14 9UR046 361.90 14 9UR073 166.05 14 9UR095 56.43 14 9UR105 107.54 14 9UR117 14.82 16 9UR205 93.37 14 9UR213 481.19 15 9UR224 336.15 15 9UR226 346.29 15 9UR227 346.29 16 9UR296 111.96 16 9UR561 324.15 15 9UR563 241.31 15 9UR566 255.59 15 9UR567 249.23 15 9UR869 132.40 14 12TW076 295.76 38 12TW093S 126.07 39 12TW117 16.38 43 12TW117* 16.38 54 12TW117= 16.38 27 12TW145 152.36 39 12TW176 320.14 38 12TW193 919.69 41 12TW205 27.78 39 12TW213 1034.97 40 12TW217 16.38 42 12TW237 353.84 41 12TW240 631.33 41 12TW276 320.14 38 12TW561 310.53 40 12TW563 310.53 40 12TW566 310.53 40 12TW567 310.53 40 12TW750 67.18 42 12UR043 271.33 14 12UR073 256.77 14 12UR093 183.14 15 12UR105 214.40 14 12UR117 27.73 16 12UR205 188.11 14

60

Numerical index

Catno

Price £ per piece

Page no

Catno

Price £ per piece

Page no

Catno

Price £ per piece

Page no

12UR213 1111.83 15 12UR236 744.35 15 12UR237 687.08 16 12UR240 1058.37 16 12UR296 149.19 16 12UR561 510.59 15 12UR563 438.22 15 12UR566 425.37 15 12UR567 405.01 15 12UR869 224.44 14 20NE002 146.63 25 20NE015 155.93 25 20NE203 70.75 25 20PW025 35.30 45 20PW050 70.59 45 20PW100 141.20 45 24NE300 190.02 25 25PW025 47.41 45 25PW050 94.78 45 25PW100 189.57 45 25PW150 284.35 45 26NE300 201.99 25 30NE002 187.03 27 30NE002* 187.03 54 30NE015 216.96 27 30NE015* 216.96 54 30NE200 15.56 27 30NE203 127.19 27 30NE205 5.05 27 32PW025 75.50 45 32PW050 151.01 45 32PW100 302.01 45 32PW150 453.01 45 34NE300 299.24 26 34NE301 314.20 26 34NE302 314.20 26 34NE303 329.91 26 36NE300 516.19 26 36NE301 542.02 26 36NE302 542.02 26 36NE303 569.11 26 40NE300 387.33 29 40NE930 226.21 29 44NE300 474.22 28 44NE304 480.07 28 44NE305 480.07 28 44NE306 495.91 28 46NE300 604.71 28 46NE307 653.54 29 46NE308 653.54 29 46NE309 705.54 29 50PW025 182.06 45 50PW050 364.10 45 50PW100 728.23 45 50PW150 1092.33 45 60NE003 711.50 32

60NE930 183.60 32 63PW025 277.50 45 63PW050 554.99 45 63PW100 1109.98 45 63PW150 1664.96 45 66NE300 1626.99 31 66NE314 1626.99 31 66NE315 1626.99 32 66NE316 1626.99 32 69NE300 1660.26 31 69NE314 1660.26 31 69NE315 1660.26 32 69NE316 1660.26 32 80D025 89.74 44 80D050 166.70 44 80D100 282.32 44 80D104 4.45 44 80D200 12.64 44 80D297 5.19 44 100D025 146.22 44 100D050 276.27 44 100D100 454.41 44 100D104 4.94 44 100D200 14.12 44 100D208 13.47 44 100D215 10.24 44 100D297 5.90 44 100HDC100 176.51 35 100HDC110 58.47 35 100HDC120 74.19 35 100HDC130 39.02 35 100HDC140 65.59 35 100HDC150 388.30 35 100MDC100 109.17 35 100MDC110 46.05 35 100MDC120 52.30 35 100MDC130 26.30 35 100MDC140 52.91 35 100MDC150 248.23 35 100OC210 59.73 34 100OC211 17.89 34 100OC230 265.53 34 100OC260 19.49 34 100OC270 22.80 34 100OC280 35.52 34 100OC410 48.45 34 100OC460 6.57 34 100OC461 225.85 34 100OC510 76.95 34 100OC520 21.77 34 100OC530 9.56 34 100OC560 14.90 34 150HDC100 235.63 35 150HDC110 93.92 35 150HDC120 119.24 36 150HDC130 112.39 36

150HDC140 153.15 36 150HDC150 488.81 36 150HDC160 223.94 36 150HDC170 172.02 36 160D025 408.69 44 160D050 503.84 44 160D104 6.65 44 160D215 33.63 44 200HDC100 271.05 36 200HDC110 130.96 36 200HDC120 167.99 36 200HDC130 136.14 36 200HDC140 168.06 36 200HDC150 877.86 36 200HDC160 317.31 36 200HDC170 255.12 36 300HDC100 339.09 36 300HDC110 262.16 36 300HDC120 305.12 37 300HDC130 170.18 37 300HDC140 198.18 37 300HDC150 1388.24 37 300HDC160 420.21 37 300HDC170 351.28 37 375TW046 713.07 38 375TW056 807.20 38 375TW066 807.20 38 375TW076 679.31 38 375TW086 773.66 38 375TW096 773.66 38 375TW099 326.08 39 375TW117 36.13 42 375TW150x45 506.89 41 375TW150x90 560.50 42 375TW205 84.12 39 375TW225x45 759.89 41 375TW225x90 759.89 42 375TW300x45 1224.01 41 375TW375x45 1679.60 40 375TW375x90 1518.95 41 375TW561 657.20 40 375TW563 657.20 40 375TW566 657.20 40 375TW567 657.20 40 375TW750 82.18 42 450TW046 997.72 38 450TW056 1037.32 38 450TW066 1037.32 38 450TW076 913.53 38 450TW086 952.85 38 450TW096 952.85 38 450TW099 492.91 39 450TW117 40.90 42 450TW117= 40.90 30 450TW150x45 549.81 41 450TW150x90 607.95 42

61

Catno

Price £ per piece

Page no

Catno

Price £ per piece

Page no

450TW205 104.02 39 450TW225x45 985.74 41 450TW225x90 985.74 42 450TW300x45 1067.96 41 450TW375x45 1971.57 41 450TW450x45 1971.57 40 450TW450x90 1971.57 41 450TW561 784.52 40 450TW563 784.52 40 450TW566 784.52 40 450TW567 784.52 40 450TW750 113.59 42 500TW046 1176.26 38 500TW056 1233.60 38 500TW066 1233.60 38 500TW076 1042.22 38 500TW086 1146.39 38 500TW096 1146.39 38 500TW099 670.81 40 500TW117 68.85 42 500TW117* 68.85 54 500TW117= 68.85 24 500TW150x45 739.35 41 500TW150x90 758.30 42 500TW205 160.72 39 500TW225x45 1109.02 41 500TW300x45 1211.71 41 500TW375x45 2751.95 41 500TW450x45 2751.95 41 500TW500x45 2793.05 40 500TW500x90 2793.05 41 500TW561 1076.17 40 500TW563 1076.17 40 500TW566 1076.17 40 500TW567 1076.17 40 500TW750 143.13 42 600TW046 1520.13 38 600TW056 1623.09 38 600TW066 1623.09 38 600TW073 688.05 38 600TW076 1342.53 38 600TW086 1513.20 38 600TW096 1513.20 38 600TW099 682.50 40 600TW117 100.12 42 600TW117= 100.12 32 600TW150x45 796.29 41 600TW150x90 880.52 42 600TW205 211.94 39 600TW225x45 1271.72 42 600TW300x45 3039.44 42 600TW375x45 3039.44 42 600TW450x45 3039.44 42 600TW500x45 3039.44 42 600TW561 1240.46 40 600TW563 1240.46 40

600TW566 1240.46 40 600TW567 1240.46 40 600TW600x45 3039.44 40 600TW600x90 3039.46 41 600TW750 165.80 42 612NE300 1693.42 31 612NE314 1693.42 31 612NE315 1693.42 32 612NE316 1693.42 32 3059730 128.17 53 3059731 42.08 53 3059732 36.85 53 3059733 30.68 53 3059735 24.67 53 3059736 22.72 53 4062303 72.14 53 4062304 72.14 54 4062305 72.14 53 4062356 72.14 53 4062357 72.14 53 4062358 72.14 53 4066677 67.58 53 71021050 1027.17 46 71031050 1324.75 46 71902400 323.85 46 71902410 8.08 47 71902420 2.04 47 71902460 3.04 47 71902500 44.15 46 71902515 69.81 46 71902522 81.28 46 71902525 38.13 46 71902570 21.97 46 71902580 21.97 46 71902590 65.75 46 71902700 117.66 46 71903225 110.93 46 71903400 404.80 46 71903410 12.16 47 71903420 3.04 47 71903460 6.10 47 71903500 63.74 46 71903570 34.95 46 71903580 34.95 46 71903590 136.38 46 71903700 181.53 46 71903725 67.16 46 71905232 113.37 46 KNW6/6 367.37 57 KNW8 448.45 57 KSG18/9 407.91 57 KSG18/9HP 84.92 57 NE950 51.34 33 NE960 78.40 33 TMC1 169.54 56

62

Notes

63

Notes

64

Important notes

All purchases are subject to our standard terms and conditions of sale, available at wavin.co.uk or call for a copy.

Prices are subject to VAT at the current rate.

Wavin operates a programme of continuous product development, and therefore reserves the right to modify or amend the specification of their products without notice. All information in this publication is given in good faith, and believed to be correct at the time of going to press. However, no responsibility can be accepted for any errors, omissions or incorrect assumptions. Users should satisfy themselves that products are suitable for the purpose and application intended.

Quality assurance

Wavin manufacturing sites operate Environmental Management Systems which comply with the requirements of and are certified to EN ISO 14001:2015, Certificate No. 42231.

All Wavin products are manufactured under a quality management system which is approved to BS EN ISO 9001: 2015.

Orders and enquiries

Tel: 0844 856 5152

For further information on our product ranges, see the following:

Wavin website

wavin.co.uk is the place to find overview of our ranges, individual item information (such as photo, dimensions, etc), literature via our download centre, news and events, blogs, online calculation tools, links to ‘How to Videos’ and more.

Download centre on wavin.co.uk

Visit our website download centre for electronic copies of:

Product, Design and Installation Guides

Price list

Safety sheets

Quality certificates

CAD files, etc.

‘How to’ Videos

To support the Osma and Wavin brands, there are a series of ‘How to’ videos to show how you can make light work of installation problems. They can be viewed at youtube.com/WavinUK

Wavin Knowledge Centre

Keep ahead of breaking news with a fresh and insightful look into the construction industry. Our aim is to keep you informed and up to date with the latest how-to guides, regulations, innovation and more. Visit blog.wavin.co.uk

Technical Tools

Register on myportal.wavin.co.uk for access to great tools to help you get the job done faster and with assured accuracy. Includes AquaCell Configurator, a Pipe Deformation tool and Inspection Chamber Selector.

Twitter Accounts

Join the conversation: @WavinUK @OsmaUK Contact

Orders and enquiries: 0844 856 5152 Complex technical queries: [email protected] literature requests: [email protected] enquires: [email protected]

Wavin LimitedRegistered OfficeEdlington LaneDoncaster | DN12 1BYTel. 0844 856 5152www.wavin.co.uk | [email protected]

OS102 – March 2020

Discover our broad portfolio at www.wavin.co.uk

Water management

Plumbing and heating

Waste water drainage

Water and gas distribution

Datacom

wavin and osma below ground & civils systems · the trigon pipe is kitemarked to wis 4-32-19...

Documents