wd speed dome - vitronic · dome to rotate smoothly, respond sensitively and aim precisely. the...

Speed Dome

MZC-81XX SERIES MZC-82XX SERIES MZC-91XX SERIES

WD Speed Dome

MZC-WD81XX SERIES MZC-WD82XX SERIES MZC-WD91XX SERIES

Installation / User’s Guide

1

INDEX

I. Notes on Safety 2

II. Introduction 3

III. Technical Data 3 1. Technical Parameters of the Intelligent High-speed Dome 3

2. Camera Parameter for High-speed Dome: (Built in Zoom Camera module). 4

IV. Installation 7 1. Installation Note 7

2. Wall mount installation guide 15

3. Ceiling mount installation guide 17

4. Surface mount installation guide 20

V. Settings 23 1. Dome Address, Transmission Speed, Protocol Setting 23

2. Speed Dome Camera Address Setting 24

3. Speed Dome Camera Communication Protocol Setting 25

4. Speed Dome Camera Transmission Speed Setting (Baud Rate Setting) 25

5. Restore the factory default 26

6. Daisy chain connection setting 26

7. RS-485 Bus Matching Resistance 27

8. AC/DC power supply 28

VI. User’s Operation 30 1. Locate a Speed Dome in a system 30

2. PTZ Operation & Control 30

3. PRESET Function 31

4. PATTERN Function 32

5. HOME function 32

6. SYSTEM MEMORY Function 32

7. SCANNING Function (between 2 positions) 32

8. Camera Menu (OSD Menu) Setting 33

9. 18x Camera Menu 34

10. 36x Camera Menu 36

Appendix 37


2

I. Notes on Safety

Please read the instructions thoroughly before installing or operating the unit.

Please do not mount the machine on an unstable surface or bracket.

Please prevent all liquids or other material from entering the dome housing.

When connecting the power source, please follow all electric safety standards and

only use the power supply designated for this device. The speed dome’s RS-485

and video signal uses TVS technology to protect it from strong electrical surges.

This technology prevents damage to the device resulting from impulse signals

such as lightning strikes or surges of power. Allow for enough distance between

the RS-485 and video signals and high-voltage equipment or cables during the

transmission process. Please do not power the unit until all connections are

secure and installation is complete.

Avoid shooting very bright objects directly into the camera’s CCD (such as the sun

or light fittings).

When the machine is not operating properly, please refer to the instructions for

information about how to service or repair your speed dome.

Please protect the unit against extremes of vibration, pressure or dampness while

transporting unit. Damage can occur from improperly packaging the unit while

shipping.

The outdoor dome camera system is designed to be installed in outdoor

environments only.


3

II. Introduction

Congratulations on purchasing the speed dome, an intelligent, high-speed dome with a

high-performance DSP camera and sophisticated zoom lens. It is an advanced surveillance

product combining an all-direction variable speed motor mechanism and digital decoder all

in one unit. It is aim to quickly scan continuously, as well as making omni-directional and

non-blind-spot monitoring into reality. The advanced stepping motor technologies enable the

dome to rotate smoothly, respond sensitively and aim precisely. The speed dome camera

has a memory function; when the power is back after blackout, it can auto restore to its

previous working status.

All of the features make the intelligent high-speed dome camera fit for a wide range of

applications such as intelligent building, bank, street of city, airport, station etc.

Use the high-performance speed dome “Where it Counts.”

III. Technical Data

1. Technical Parameters of the Intelligent High-speed Dome

Model Speed Dome

Power Supply AC24V±15%

Operating temperature Outdoor : - 20~+50

Operating moisture ≤95%(at non-condensing)

Power consumption 25W ~ 45W(max)

Communication RS485 bus

Communication transmission speed 1200/2400/4800/9600bps

Horizontal rotation speed 1° - 240°(1-64 grade shift gears)

Horizontal rotation range 360° unlimited rotation

Tilt rotation range 90°

Auto flip Rotates 180° when camera tilts to the vertical position

Auto zoom speed control Control speed auto-adjusted according to zoom length changing

2 points scan Can set freely

Preset Positions 128 preset positions

Cruise Tour: Run Presets (1 ~ 10)

Cruise Points Qty group 10 preset positions

Heater ( option ) 24VAC


4

2. Camera Parameter for High-speed Dome: (Built in Zoom Camera module).

18x Camera

TV System PAL NTSC

Image Sensor 1/4”SONY Super-HAD CCD

Number of Total Pixels 470,000 Pixels 410,000 Pixels

Resolution Color:540TVL, B/W:560TVL

Minimum Illumination Color:[email protected] (30IRE) ;

B/W:[email protected] (30IRE)

Video Output CVBS 1.0Vp-p, 75Ω

Signal to Noise Ratio More than 50dB

Gamma Correction 0.45

Mechanical IR Cut Filter (ICR) ICR Removable, Lux Level Adjustable, 15 steps

Menu OSD

Language English, Traditional/Simplified Chinese, Japanese

Automatic Electronic Shutter 1/50~10000sec 9steps 1/60~10000sec 9steps

Automatic Gain Control Automatic

Automatic White Balance Automatic

Back Light Compensation ON / OFF

Flickerless ON / OFF

Automatic IRIS, Focus Automatic

Digital Zoom NA

Lens 36x zoom f=3.4~122.4mm/57.8 o

~1.7 o

Communication ; Controls RS-485 ; PAN / TILT, LENS

Auto Pan Yes

Tour Pattern 1 Group (accommodates preset #1~#10)

Home Function Yes

System Memory Yes

Panning Range ; Panning Speed

360 o

Continuous ; 0.2 o ~240

o /sec.

Tilt Range ; Tilt Speed 0 o

~90 o

; 0.2 o

~120 o

/sec.

Pan, Tilt Accuracy ±0.02o

Preset Positions 128 Positions

Alarm-In ; Alarm-Out 4 In, 1 Out

Water Resistance NA

Power Supply ; Consumption 24Vdc/24Vac ; 25W

Operation ; Storage Temp. 0 o

C~50 o

C ; -10 o

C~60 o

C

Operation ; Storage Humidity Maximum:RH80% ; RH90%

Dimensions 200(DIA)x134(H)mm

Net Weight 2,800g

Installation / User’s Guide 5

36x Camera

TV System PAL NTSC

Image Sensor 1/4”SONY Super-HAD CCD


Resolution Color:540TVL, B/W:560TVL

Minimum Illumination Color:[email protected] (30IRE) ;

B/W:[email protected] (30IRE)



Gamma Correction 0.45

Mechanical IR Cut Filter (ICR) ICR Removable, Lux Level Adjustable, 15 steps

Menu OSD

Language English, Traditional/Simplified Chinese, Japanese

Automatic Electronic Shutter 1/50~10000sec 9steps 1/60~10000sec 9steps


Automatic White Balance Automatic


Flickerless ON / OFF


Digital Zoom NA

Lens 36x zoom f=3.4~122.4mm/57.8 o

~1.7 o


Auto Pan Yes


Home Function Yes

System Memory Yes

Panning Range ; Panning Speed

360o Continuous ; 0.2

o ~240

o /sec.

Tilt Range ; Tilt Speed 0 o

~90 o

; 0.2 o

~120 o

/sec.

Pan, Tilt Accuracy ±0.02 o



Water Resistance IP66

Power Supply ; Consumption 24Vdc/24Vac ; 25W (45W, when the Optional Heater is on)

Operation ; Storage Temp. -10 o

C~50 o

C ; -20 o

C~60 o

C



Net Weight 4,050g


WD 36x Camera

TV System PAL NTSC

Image Sensor 1/4" Sony Exview-HAD CCD


Resolution 530TVL

Minimum Illumination [email protected], Slow Shutter Mode:[email protected],

B/W: 0.01 [email protected]


Wide Dynamic Range ON (128X) / OFF


Mechanical IR Cut Filter (ICR) IR Cut Filter Removable

Menu OSD

Language English

Automatic Electronic Shutter 1/3(4)~10000sec 20steps


Automatic White Balance Automatic / ATW / INDOOR / OUTDOOR / MANUAL


Flickerless N/A


Digital Zoom 12X

Lens 36x zoom f=3.4~122.4mm/57.8o~1.7o


Auto Pan Yes


Home Function Yes

System Memory Yes

Panning Range ; Panning

Speed

360o Continuous ; 0.2o~240o /sec.

Tilt Range ; Tilt Speed 0o~90o ; 0.2o~120o/sec.

Pan, Tilt Accuracy 0.02o



Water Resistance IP66

Power Supply ; Consumption 24Vdc/24Vac ; 25W (45W, when the Optional Heater is on)

Operation ; Storage Temp. -10oC~50oC ; -20oC~60oC



Net Weight 4,050g


IV. Installation

1. Installation Note

Power supply note

Wrong

Right

Note Must use the electric adapter that supply with the product to supply the power

to each speed dome. One adapter (AC 24V±3V current 3A) can not support

more than one dome camera to avoid image disturbance. Please check if

the voltage in your city is in the scope of supplied power adaptor.

Don’t use uncertified power supply.

Don’t use one adapter to supply

more than one speed dome in order

to avoiding signal disturbance.

One adapter for one speed dome only.

Input voltage should be in AC24±3V current 3A.


8

Maintenance note

Wrong

No submerged

No high-pressure-water

No installation in erosive place


Right

Note It is capable to water resistance, but no submerged. Don’t use

high-pressure-water upward to the dome. Installation place should avoid

erosive water (e.g. air-condition water) dropped to the dome.

Water resistance

Use soft waterish cloth to clean cover

No erosive objects in installation place


10

Don’t toward the CCD sensor face bright light directly and in long

duration Wrong(Don’t let the CCD sensor face to dazzling light directly.)

Right(Turn the CCD away from the bright light source in order to extend

the camera’s life.)

Note Avoid the CCD sensor face to dazzling light directly. Long time facing to bright

light source may cause the CCD sensor permanently damaged.


11

Don’t install unit when power “ON” Wrong Right

Note Don’t install unit when power ON. During the process of installation, the power

supply must be (unplug) at OFF status.

Don’t install unit power “ON”


12

Don’t forcibly turn camera by hand Wrong Right

Note When testing the speed dome with movements, the control equipments are

required. Don’t forcibly turn the camera by hands.

When testing speed dome camera, don’t forcibly turn camera by hand, as it will cause problems to the camera.

Control equipment (e.g. keyboard, DVR) is required to control the camera movement.


Distance at Video signal transmission and RS-485 control Wrong Right

RS-485 1200m control 32 domes≧ ≧

Video signal dis 300m≧

Image quality decrease, or Out of control

RS-485 dis＜1200m control less than 32 domes

Video signal dis＜300m

Image clear Control steadily


Notice

1. Video signal’s transmission distance is 300m by using coaxial-cable. Please

use video compensator or optical cable transmission facilities. When distance

is required conger than 300M.

2. Please use twisted-pair wire for RS-485 data transmission.

3. If RS-485 transmission distance is further than 1200m, please use signal

repeater or signal distributor.

4. One RS-485 line can only accommodates 32 speed domes at most. If the

number is more than 32, please use signal distributor to expand.

5. Cabling at RS-485 should use linear connection (daisy link). If for star linking,

please use signal distributor.

6. Cabling at RS-485 should be kept away from high-voltage wire, electromotor

etc. to avoid disturbance or interference.


15

2. Wall mount installation guide

Step 1

Please drill the installation holes site in M8 Bolt size.

Step 2

Assemble Sketch

Bolt(M5)

Housing

Inner housing

Camera Module

Transparent Dome Bolt(M3*3)

Mounting Bracket


16

Step 3

Take camera module out of package, set the switcher on mode. (Please refer to P.19.20.21 of the manual)

Hold the module, align the connection plate to the connection pins and insert the module (the power supply must be at OFF status), twist the module veerly to the end, to fix it on the base.

Step 4

Step 5


17

3. Ceiling mount installation guide

Step 1

Use soft cloth to clean cover in order not to scratch the corer surface.

Please wear proactive glove to twist and fix the dome cover.

Step 2

Please make an installation hole site in M8 Bolt size.

BNC Video Output Port

AC 24V Power Input Port

RS485 Signal Control Port

Fix board

Housing

Module

Assemble Sketch


18

Step 3

Align the holes on board and ceiling, use spanner to lock the screws.

Step 4

Step 5

Take out module of carton, set the switcher.

Please place the safety lock into the hook on the dome.

Use tool to make breach Put housing on fix board, place

wire in the breach, twist cover clockwise to fix it on the board.


19

Step 6

Hold module with two hands, align arrow at unlocking label, insert terminal to the socket. (The power must be at OFF status)

Step 7

Then twist module clockwise

until arrow pointing at locking label in order to fix module on the board.


20

4. Surface mount installation guide

Step 1

(1) To mount the bracket to

the ceiling , the ceiling

needs to be excavated.

(2) The diameter for the

mount hardware should

be between 175mm~180mm.

(3) The thickness of the ceiling

should be between 5mm

~20mm.

Step 2

Driving-unit

Screw-base Installation configuration

Ceiling

Mount hardware


(1) Please release the screws attached under the mount hardware to it’s most flexibility.(In case of mounting on the 20mm ceiling).

(2) Push the hardware up to the most-upper-position of the excavated ceiling, and meanwhile ,the clips will be stuck on the ceiling. (3) Fasten the released screws and then the clip will fix on the ceiling.

Step 3

(1) Take the driving-unit from the package and set the related setting of the dip switch. (2) Connect the hook and safety-ring to avoid accidental falling. (3) Hold the driving-unit, connect the terminal to the socket, and then twist clockwise to

fix the board.

Hook

Safety-ring

Driving-unit Mount-bracket

Twist clockwise to fasten

Check the upper position


Step 4

Twist the screw-base clockwise to make it fix firmly.

Finalized installation diagram

Screw-base


23

V. Settings

1. Dome Address, Transmission Speed, Protocol Setting

Before the dome is installed, the communication protocol, baud rate and dome address,

should be confirmed. Set the Dip switches to keeping the setting consistent with the control

system. The relative code switch site and connecting wires are diagramed below for

reference.

Please set relative communication protocol, baud rate, matching resistance, etc.


24

2. Speed Dome Camera Address Setting The address code (Cam ID) for the speed dome must to be properly set before use to

ensure accurate addressing of the domes for control at center. The address code is made up

of SW201 (8-bits) dip switch on PCB board. The 8-bit switch uses the 8421 binary coded

decimal system; the largest value is 256. “1” means ON status and “0” means OFF status.

Each dome address code (Cam ID) that display at keyboard or control devices is response

to the settings shoeing in the chart below: (see the following figure and the address/digits in

following chart)

Note

1. When all switches at “OFF” the address code of speed dome is 1.

2. When you input 1 + Cam at control keyboard (MCU-PTZ091), the keyboard

(MCU-PTZ091) should communicate with the speed dome to control.

3. Other addresses , please refer to the table above for settling reference.

4. Please note the Cam ID address for PELCO-D and PELCO-P protocol modes are

different. Please check the system protocol type before making the Camera ID setting.

5. Cable pin out assignment

Color Function

Video Out

Red AC 24V / DC 24V

Blue AC 24V / DC GND

Yellow RX+

Orange RX-

Gray TX+

Green TX-


25

3. Speed Dome Camera Communication Protocol Setting

The 1st, 2nd and 3rd bits in SW202 are used to set communication protocol (see following

figure)

Note

After establishing the communication protocol, please restart the unit to save the

changes.

Please ensure that the control device and the camera are using the same protocol.

4. Speed Dome Camera Transmission Speed Setting (Baud Rate Setting)

The 4th and 5th bits of SW202 on the PCB board are used to set the baud rate (see

following figure).

The default baud rate setting is 2400, D, type, addr 1. Baud Rate Options: 1200BIT/S 、

2400BIT/S 、4800BIT/s、9600BIT/s

Please refer to the controlling device and protocol for baud rate settings.

Note

After set the speed, please restart the unit to save the changes.

Restore

Daisy chain


5. Restore the factory default

Please keep the dip switch at the position” off” when using the speed dome.

The switch is designed to restore the factory default, and it is advised to be controlled by the

engineers of distributor locally. After operating this function, all the previous settings will be

removed.

Operating procedure:

1. Turn the dip switch to “on”

2. Then the speed dome will start initializing.

3. Turn the dip switch to “off”

6. Daisy chain connection setting

When multiple speed domes with 4 wire RS-485 are connected, please set the daisy chain

Dip Switch to “on” when using this function.


27

7. RS-485 Bus Matching Resistance

For better centralized control, a matching resistance should be set in parallel via RS-485

interface at the speed dome that is farthest from the center controller. By doing this, those

signal reflection and interference from the RS-485 signal and the like can be cleared up.

There is a switcher for controlling of the matching resistance at the end of SW202 on the

PCB board. And the matching resistance is connected to the RS-485 cable when the “No. 8”

switcher is set to “ON” status.

Note

When dome is out of control or doesn’t work under RS-485 BUS control status,

please set switch of matching resistance as ON status; so that it can clear up bad

phenomenon.

If dome address, baud rate and communication protocol is required to be reset after

finish installation, please ensure dome is at power off status.

Protocol

Baud Rate

Restore

Daisy Chain

Matching Resistance


28

8. AC/DC power supply

The default power supply is AC 24V, if you choose to power with DC24V, please shift the

power code AC 24 + (red colored) to DC 24V input on the drive board, and also shift the

power code AC24 – (blue colored) to the DC GND. Please refer to the configuration as

below.

AC 24V


DC 24V


VI. User’s Operation

The Speed Domes have been implemented and compatible to PELCO (D/P type) protocol that works with all devices such as DVR, Video Servers, PC, and keyboards that compatible to the same protocol for system integration and operation handy.

1. Locate a Speed Dome in a system

Set ID address of a speed dome：

The ID address of each Speed Dome has to be unique and only one in a system; it can be set by the on-board dip-switch that fore-mentioned on page 6. When the ID address set properly, by external controller and keyboard, the Speed dome will be operated and controlled. The speed domes can be programmed up to 128 of ID address. However, subjected to different control device and keyboard, the maximum number of speed dome in a system will be various. For example, if controlled by MCU-PTZ091, there are maximum 99 units of speed domes in a system at direct connection mode.

To call a speed dome：

If the protocol and ID address of a speed dome has been properly setup, the keyboard will be able to call and operate the speed dome. For say, if a speed dome set ID as #1 and controlled by MCU-PTZ091 keyboard, you can press “1” and “CAM” on the controller’s keypad, you will then configure to the speed dome by the keyboard and control/operate the speed dome (at ID #1). The users can do the same for other configured speed domes in the system by calling their proper ID number.

2. PTZ Operation & Control

PAN (360˚) movement The speed dome can move continuous 360 with controls. The speed dome features

64-step speed to correspond with the operation at the joystick—when user move the

joystick fast, the speed dome will move fast; and, vise versa. TILT (90˚) movement

With keyboard, the Speed dome can perform vertical movement (from 90 to 0 ) at

various speed, including Auto-flip function. Auto Flipping

When tilt down at 90 position, the speed dome will automatically flip over to track or

follow a moving object beneath and passing by.

Focusing With auto-focus feature, it will focus on the center of the view window automatically to ensure the image stays clear and sharp. Focus can also be adjusted manually to

suit users’ preferences.


Note: When the followings occur, the speed dome may not be able to focus properly: When the object is not at the camera＇s viewing center;

With complicated front and background, the good focusing can not be ensured for all. The taken object is too bright—if it is lit by the laminator such as spotlight, neon-lamb, etc. Fast-moving object Objects stay behind glasses with water-drops or covered by a layer of dust A big plain object and dull in color or background—such as a plain wall

Objects stay in the dark or dim environments that can＇t be seen clearly.

Zoom In/Out

The motorized lens to Zoom-in and Zoom-out can be controlled by controller. There are normally two different zoom functions available in the built-in Zoom camera module-- Optical Zoom, and Digital Zoom. But the performance and the zooming rate are various and subjected to the core zoom module.

Micro movement at Zoom In When Speed Dome performs Zoom-In, the PAN/TILT movements will automatically tune in micro-step to make sure the close-up track on the object, and to avoid the not out of range or loss track problem.

IRIS control The factory default is set to be auto-IRIS. IRIS will be adjusted subject to the light change for optimum brightness on video. Users can adjust the IRIS to open or to close or other adjustments for suitable brightness.

3. PRESET Function

With the PRESET feature, it memorizes a position, including its PAN/TILT angle, Zoom & Focus. PRESET positions can be called by controller so that the object can be located quickly and handy. With MCU-PTZ091 control keyboard, each Speed Dome can set to maximum 128 PRESET positions.

‧ Note: some of the 128 PRESETs are defined as special functions, please refer to the “Special Function Table” (at the end of the manual) Call a PRESET position

Press the numeric key and the PRESET function key on the controller, And then this preset will be called and performing the memorized position.

EX: 1 + preset The preset #1 will be called to perform.

Save a PRESET position

Use the controller to operate the Speed Dome at the wanted position (including viewing angle and size of image). And, enter a number with the numeric keypad, then press the ADD function key to confirm and save. Thereafter, you can use the call-preset procedure as mentioned above to test the added preset point.

EX: 1 + add The preset at position #1 will be confirmed and saved.

Delete a PRESET position

Enter a number from the controller’s keypad and press the DEL function key to delete

the preset point.

EX: 1 + Del The preset #1 is now deleted.


4. PATTERN Function With the PATTERN feature, it can unite PRESET #1 ~ #10 to group a pattern and perform the presets in order continuously.

Execute PATTERN function Press the PATTERN function key on the controller to activate the PATTERN function.

Note:

(1) The PATTERN function is to group the PRESETs from #1 to #10 and perform all position orderly continuously. (2) To call, add, or delete a preset point as we mentioned before. (3) The maximum speed between every two presets is 280 /sec and each position will stop

for 5 seconds. (4) Press any key or use the joystick to stop the PATTERN function,.

5. HOME function This function is to perform the indicated preset position (HOME) when the Speed Dome is idle for more than 20 seconds.

Set up HOME position

Use the keyboard to set the position (including viewing angle and size of image) and press 53 + ADD keys to save the preset 53 as the HOME position .

Note: If the Home function is activated, when not being operated for around 20 seconds, the speed dome will automatically swing back to the Home position until the next command is made.

Activate the HOME function Press 54 + add to activate this function.

Note: The PATTERN is in higher priority than the HOME function. When both functions are enabled, the speed dome will choose to activate PATTERN function over HOME function. After the PATTERN function stopped for around 20 seconds, the speed dome will swing back to home position automatically.

To deactivate the HOME function

Press 55 + add to deactivate this function.

6. SYSTEM MEMORY Function With the System-Memory feature, it can memorize the system operations and setups before blackout. After the power back, the speed domes will restore the system same as before.

This function can save a lot of time on resetting up the speed domes after each system down.

7. SCANNING Function (between 2 positions) Have to set the Left Limit and Right Limit positions before activate the function.

Left Limit/Right Limit position setup

(1) Left Limit position: Press 92 + preset keys to save the start point of

the scanning function


(2) Right Limit position: Press 93 + preset keys to save the finish point of

the scanning function

Execute the Scanning function: with the following options (1) At Middle speed: Press 99 + preset keys or Auto Scan key , the speed

dome will move in between of the start and the finish point at middle speed.

8. Camera Menu (OSD Menu) Setting Joystick up/down to select item from setup menu. Joystick move to the right to increase value (or on/off mode change). Joystick move to the left to decrease value (or on/off mode change).

OSD Menu

(1) Press 95 + preset to call out the OSD Menu for system settings.

(2) Use the keypads or the joystick to change the settings (3) Use left and right buttons or joystick to adjust the values


9. 18x Camera Menu

(1) NEGATIVE：OFF

Status OFF ON

(2) DZOOM：OFF (Digital zoom switch)

Status OFF ON

(3) FOCUS：AUTO (Auto Focus)

Status AUTO (auto) MAN (Manual)

(4) MIRROR：OFF (Right-Left shift)

Status OFF ON

(5) SLOWSHUTTER：ON

Status OFF ON

(6) ICR：AUTO (B/W – color auto shift)

Mode AUTO OFF

(7) COLOR：OFF (Color display)

Status OFF ON

(8) FREEZE：ON (Picture Freeze)

Status OFF ON (9) DISPAY：OFF (Screen display)

Status OFF ON

(10) BACKLIGHT：ON

Status OFF ON

(11) WBC MODE： AUTO (white balance)

Status AUTO INDOOR OUTDOOR MAN ATW

(12) RGAIN：(Red gain) (WBC mode → MAN)

Move right to increase the value. Move Left to decrease the value.

(13) BGAIN：(Blue gain) (WBC mode → MAN)


(14) EXPOSURE：(Exposure Select)

Status AUTO PRIORITY MAN IRIS-PRIORITY BRIGHT

(15) BRIGHT：(Brightness Adjustment)



(16) GAIN：


(17) SHUTTER：


(18) IRIS：(Iris adjustment)


(19) SET PRIVACY ZONE：

No function.

(20) EXPOSURE COMPENSATION：(Exposure compensation ON/OFF)

Status OFF ON

(21) EXPOSURE COMPENSATION：(Exposure compensation adjustment)


(22) STABILIZER：OFF

Status OFF ON (23) WDR:OFF Status OFF ON (24) FLIP:OFF Status OFF ON

(25) SAVE SETTING (Set saving) Move right and save current set.

(26) DEFAULT

(27) EXIT MENU (Exit menu) Move right and exit the menu.


10. 36x Camera Menu

MAIN MENU

SYSTEM

DISPLAY

PRESET

CAMERA

ALARM

REBOOT

EXIT

LANGUAGE CAMERA TITLE

BAUD RATE

PROTOCOL

FIRMWARE

RESTORE

CAMERA ID

CARMERA ID

CAMERA TITLE

PRESET TITLE

DATE/TIME

ALARM MESSAG

ZOOM RATIO

PRESET NO.

POSI

SAVE

DELETE

TITLE

PAUSE TIME

LENS IMAGE

FOCUS

IRIS

BRIGHTNESS

ZOOM SPD

FOCUS SPD

DAY/NIGHT

NIGHT LIGHT SOURCE SET

EXPOSURE MODE

WHITE BALANCE

SHARPNESS

BACKLIGHT

FLC

AGC

SYNC

MIRROR

POS./NEG.

PRIVACY MASK

IN SWITCH

IN MODE OUT SWITCH OUT TIME

ALARM MESSAGE


Appendix

SPECIAL FUNCTIONS SETUP – Reference Table

preset key add key

33 FLIP

34 Move to HOME

53 Set Home position

54 Activate Home function

55 Disable Home function

61 to exit option in MENU

90 PAN : 360∘

92 SET Left Limit

93 SET Right Limit

95 go to OSD MENU

99 Scanning at middle speed

wd speed dome - vitronic · dome to rotate smoothly, respond sensitively and aim precisely. the...

Documents