wds technical support guide - netcom · wds (wireless distribution system) mode – the np731...
TRANSCRIPT
Technical Support Guide
Configuring NP731 in WDS mode
Configuring NP731 in WDS mode 1 of 18
© NetComm Wireless 2017
NP731 system overview
Designed to meet the needs of today’s most demanding wireless LAN deployments, the NP731 offers a solution to create a
reliable and scalable wireless network.
The NP731 is an outdoor device that will operate in access point, repeater and WDS bridge mode. Its rugged IP68-rated metal
housing is weather proof, pressure balancing, water-tight and rust-resistant, making it an ideal solution for deployments in
harsh conditions, such as outdoor or industrial environments.
With its multi-mode set up, the device can be used in many cases to increase and enhance wireless coverage.
The NP731 has four modes of operation:
Repeater mode (default) – the NP731 repeats the wireless signal of your existing network to provide an increased
area of coverage for your premises.
Access Point mode – the NP731 connects to an existing router via Ethernet and provides a wireless signal for wireless
devices. This is useful in situations where there is no existing wireless access point or where you wish to provide a
wireless signal to a remote area from where the router is located.
CPE (Customer Premises Equipment) mode – the NP731 connects wirelessly to a remote network and provides access
to that network to clients connected via Ethernet. Use of a switch is required for multiple clients.
WDS (Wireless Distribution System) mode – the NP731 connects to up to eight (8) other NP731 units to create a
wireless mesh network. This is like repeater mode but in WDS mode, the NP731 uses a single MAC address to provide
seamless roaming.
Purpose of the document
This document provides an in-depth explanation of how to set up multiple NP731 devices in the WDS (Wireless Distribution
System) mode, the fourth mode described in the above overview.
2 of 18 Technical Support Guide
© NetComm Wireless 2017
Contents
NP731 system overview....................................................................................................................................................................... 1
Purpose of the document ................................................................................................................................................................................................. 1
Configuring NP731s for WDS mode ...................................................................................................................................................... 3
WDS mode ........................................................................................................................................................................................................................ 3 1. Configure AP device Network settings ................................................................................................................................................................ 4 2. Configure Repeater devices Network settings (optional) ................................................................................................................................... 5 3. Configure AP and WDS Repeater devices ........................................................................................................................................................... 7 4.a Configure Repeater WDS Link settings for Access Point (AP) ............................................................................................................................ 10 4.b Configure AP WDS Link settings for each Repeater device ............................................................................................................................... 12 WDS diagram .................................................................................................................................................................................................................. 13
Notes on Checking a MAC Address .................................................................................................................................................... 14
Enter MAC Address ......................................................................................................................................................................................................... 14
Extending the WDS ............................................................................................................................................................................ 15
1 Changes to Configuration of Repeater Device 3 ............................................................................................................................................... 15 2 Changes to Configuration of Repeater Device 4 ............................................................................................................................................... 16 3. Changes to Access Point (AP) Device ................................................................................................................................................................ 17 Extended WDS diagram .................................................................................................................................................................................................. 18
Configuring NP731 in WDS mode 3 of 18 © NetComm Wireless 2017
Configuring NP731s for WDS mode
WDS mode
One NP731 connects to an existing router via Ethernet and provides a wireless signal for wireless devices. All other NP731
devices repeat the wireless signals of your existing network to provide coverage to a greater area of your premises. The
NP731 can connect with up to eight (8) other NP731 devices to create a wireless mesh network.
Example used in this Guide
In this guide, we will first configure the NP731 device connected as an access point (AP) to the Router, and then we will
configure the other four NP731 devices on the WDS system.
In the example used in this guide, the main router’s network address is: 192.168.20.0 mask 255.255.255.0
Settings not mentioned
If settings are not specifically mentioned in this document, it is assumed that the factory default settings will be used.
4 of 18 Technical Support Guide
© NetComm Wireless 2017
1. Configure AP device Network settings
The first NP731 is connected directly with the router as the Access Point (AP).
The router will be the only device that is ‘seen’ from the Internet, the AP or Repeater devices will ‘use’ an IP Address which
falls in the router’s network address range.
1 Navigate to System > Network Interface:
a Make the following Network settings only in the AP device:
Item Setting Notes
Mode Static Use same setting for AP and all Repeaters.
IP Address 192.168.20.254 Enter the same network address range as the main
router (192.168.20.0/24).
Netmask 255.255.255.0
Default Gateway 192.168.20.1 IP address of the main router.
Primary DNS Server 192.168.20.1 IP address of the main router.
2 Click the SAVE button.
3 Restart the device.
Configuring NP731 in WDS mode 5 of 18 © NetComm Wireless 2017
2. Configure Repeater devices Network settings (optional)
Strictly speaking, this configuration is not required. The default network settings on the Repeaters will work, but each
Repeater will be on a different network.
We suggest including all devices on the same LAN network, so that any client connected to the LAN can access both the AP
and all the Repeaters in the WDS.
1 For each repeater, navigate to its System > Network Interface:
a Make the following Network settings on each numbered Repeater device:
Item Setting Notes
Mode Static Use same setting for AP and all Repeaters.
IP Address for
Repeater device 1
192.168.20.253 The AP is set to 192.168.20.254.
IP Address for
Repeater device 2
192.168.20.252 The AP is set to 192.168.20.254.
IP Address for
Repeater device 3
192.168.20.251 The AP is set to 192.168.20.254.
Extra Repeater devices:
Repeater device 4
Repeater device 5
Repeater device 6
Repeater device 7
192.168.20.250
192.168.20.249
192.168.20.248
192.168.20.247
If you add extra devices, use these IP Addresses.
6 of 18 Technical Support Guide
© NetComm Wireless 2017
Item Setting Notes
Repeater device 8 192.168.20.246 Note that the maximum number of devices on a
WDS system is eight (8) repeater devices.
Netmask 255.255.255.0 Same for AP and all Repeaters.
Default Gateway 192.168.20.1 Same for AP and all Repeaters.
Primary DNS Server 192.168.20.1 Same for AP and all Repeaters.
2 Click the SAVE button.
3 Restart each device.
Configuring NP731 in WDS mode 7 of 18 © NetComm Wireless 2017
3. Configure AP and WDS Repeater devices
In both the AP and all the other WDS mode Repeater devices:
1 Navigate to System > Operating mode:
a Select AP mode as the Operating Mode.
Important – This Operating Mode setting must be same in all the WDS devices in the network.
2 Navigate to AP > General and configure the Band, Protocol and Channel details.
8 of 18 Technical Support Guide
© NetComm Wireless 2017
a Make the following settings:
Item Setting Notes
Band Either 2.4GHz or 5GHz Use the same Band for AP and all Repeaters.
Protocol 802.11g+802.11n Do not check Pure 11n
Channel Width 40 MHz Use the same Channel Width for AP and all Repeaters.
Channel Range: 1 - 13 Use the same channel for AP and all Repeaters.
Important – These configuration settings must be the same in all the WDS devices in the network.
3 Navigate to AP > VAP config and configure the ESSID.
a Make the following settings:
Item Setting Notes
ESSID XxxxXxx 1234 Enter any alpha-numeric name, spaces are allowed.
Use same ESSID for AP and all Repeaters.
Important – These configuration settings must be same in all the WDS devices in the network.
Configuring NP731 in WDS mode 9 of 18 © NetComm Wireless 2017
4 Navigate to AP > Security and configure the Pre-Shared Key details.
a Make the following settings:
Item Setting Notes
Cipher Suite WPA2 We recommend WPA2.
Use the same Cipher Suite type for the AP and all
Repeaters.
Pre-shared Key Type Passphrase We recommend Passphrase.
Use the same Pre-Shared Key type for the AP and all
Repeaters.
Pre-shared Key Enter key (password)
For example:
N3tC0mmm
Must be 8 to 63 Alpha/numeric/special characters,
no spaces.
Key Type = Passphrase
Use the same Pre-Shared Key for the AP and all
Repeaters.
Important – These configuration settings must be same in all the WDS devices in the network.
10 of 18 Technical Support Guide
© NetComm Wireless 2017
5 Navigate to the AP > Repeater page:
Important – The AP > Repeater Settings are different for the AP (see section WDS Link settings for Access Point, below) and the Repeaters (see section Configure AP WDS Link settings, below).
4.a Configure Repeater WDS Link settings for Access Point (AP)
a For only the WDS Access Point, the MAC addresses
of the other Repeater NP731 devices must each be
referenced to a numbered WDS Link.
b This referencing is accomplished using the WDS
Profile drop-down selector in conjunction with the
Remote AP MAC Address field, see image on right.
Item Setting(s) Notes
Repeater Type WDS WES Use same settings for the AP and all Repeaters.
WDS Profile
drop down list
WDS Link 1
(MAC address of 1St repeater device)
1. Select WDS Link 1 from the drop-down list,
2. Enter the MAC address* of the first Repeater device
into the Remote AP MAC Address field, see below,
3. Click the SAVE button
4. Repeat these steps for the other Repeater devices.
WDS Link 2
(MAC address of 2nd repeater device)
1. Then select WDS Link 2 from the drop-down list,
2. Enter the MAC address* of the second Repeater
device into the Remote AP MAC Address field, see
below,
Configuring NP731 in WDS mode 11 of 18
© NetComm Wireless 2017
Item Setting(s) Notes
3. Click the SAVE button
4. Repeat these steps for the other Repeater devices.
WDS Link 3
(MAC address of 3rd repeater device)
1. Then select WDS Link 3 from the drop-down list,
2. Enter the MAC address* of the third Repeater device
into the Remote AP MAC Address field, see below,
3. Click the SAVE button
WDS Select: Enable Select Enable from the drop-down list for the AP and
all Repeater devices in the WDS network.
WDS Link Address Un-editable system data. This is the current AP device’s MAC address.
Remote AP MAC Address Enter the MAC address* for each
of the linked repeater devices
here.
After selecting the WDS Link number for each repeater
device from the WDS Profile drop-down list, see above,
enter its unique MAC address* and click SAVE.
Then select the next WDS Link number and repeat the
process for each of the remaining repeater devices.
Security Type WPA-Personal Use same settings for the AP and all Repeaters.
Cipher State WPA2 Use same settings for the AP and all Repeaters.
Pre-shared Key Type Passphrase Use same settings for the AP and all Repeaters.
Pre-shared Key The 8 to 63 characters key/
password should appear here as
it was previously entered at the
AP > Security step, see step AP >
Security on page 9 [above].
Use same key/password for the AP and all Repeaters.
SAVE Button Click to save changes.
Note – You must individually SAVE the WDS Profile
and MAC address details for each repeater device one
at a time.
Clicking SAVE will not close the page.
CLEAR Button Click to clear changes and return to previous settings.
c Click SAVE.
d Restart the device.
* Each NP731 device’s MAC Address can be found on the System Overview page (Status > Overview) of its web interface,
refer to Notes on Checking a MAC Address on page 14.
12 of 18 Technical Support Guide
© NetComm Wireless 2017
4.b Configure AP WDS Link settings for each Repeater device
a For each WDS Repeater NP731 enter the following settings:
Item Setting(s) Notes
Repeater Type WDS WES Use same settings for the AP and all Repeaters.
WDS profile
drop down list
WDS Link 1 1. Select WDS Link 1 from the drop-down list,
2. Enter the MAC address* of the Access Point (AP)
device into the Remote AP MAC Address field, see
below.
3. Click the SAVE button.
WDS Links 2, 3, 4, 5, 6, 7 and 8 Do not make any changes.
WDS Select: Enable Select Enable from the drop-down list for the AP and
all Repeater devices in the WDS network.
WDS Link Address Un-editable system data. This is the current repeater device’s MAC Address*.
Remote AP MAC Address Enter the MAC address* of the
AP NP731 device.
All the Repeater NP731 devices have the MAC
address* of the Access Point (AP) device entered here.
Security Type WPA-Personal Use same settings for the AP and all Repeaters.
Cipher State WPA2 Use same settings for the AP and all Repeaters.
Pre-shared Key Type Passphrase Use same settings for the AP and all Repeaters.
Pre-shared Key The 8 to 63 characters key/
password should appear here as
it was previously entered at the
AP > Security step, see step AP >
Security on page 9 [above].
Use same key/password for the AP and all Repeaters.
SAVE Button Click to save changes.
CLEAR Button Click to clear changes and return to previous settings.
b Click SAVE.
c Restart the device.
* Each NP731 device’s MAC Address can be found on the System Overview page (Status > Overview) of its web interface,
refer to Notes on Checking a MAC Address on page 14.
Note – A maximum of eight (8) NP731 devices can be included in WDS (Wireless Distribution System) network.
Configuring NP731 in WDS mode 13 of 18
© NetComm Wireless 2017
WDS diagram
This diagram shows the network settings of the AP and Repeater devices in the WDS system set up using this guide.
14 of 18 Technical Support Guide
© NetComm Wireless 2017
Notes on Checking a MAC Address
The MAC address for each NP731 device (regardless of whether they are the Access Point or Repeaters) can be checked using
the following procedure.
1 Connect the NP731 device to the router using an ethernet cable.
2 Power on the NP731 device
3 Open a browser and type in the NP731 device’s URL.
4 Click the Status tab and select the Overview tabbed page.
5 The MAC Address appears in the Radio Status section of the System Overview page:
6 Make a note of the MAC Address
7 Repeat the process for each repeater device and the AP device.
Enter MAC Address
You enter the MAC Addresses at the following points in the WDS setup process:
Enter each repeater device’s MAC Address when you configure the WDS Profile for each of the repeater devices for
Access Point, see section WDS Link settings for Access Point, above, and
Enter the AP’s MAC Address when you configure the WDS Profile for the AP Device on each of the Repeater Devices,
see section Configure AP WDS Link settings, above.
Configuring NP731 in WDS mode 15 of 18
© NetComm Wireless 2017
Extending the WDS
It is possible to extend the WDS past its normal range by linking two Repeaters together while still using only one Access
Point (AP). In this case data will travel to/from the final Repeater via another repeater and not directly to/through only the
AP.
In the scenario illustrated in the diagram Repeater Device 4 is out of WiFi range from the AP and Device 4 will access it via
Repeater Device 2.
The following steps outline the changes that are required to configure this extension of the WDS system.
Refer to the first section of this Support Guide (Configuring NP731s for WDS mode) for more detailed descriptions of these
pages and settings.
1. Changes to Configuration of Repeater Device 3
The following parameters in Repeater Device 3 need to be changed and/or copied to Repeater Device 4:
Location Parameter New Value
Network Settings
System > Network Interface
IP Address
Netmask
Default Gateway
Primary DNS Server
No change
No change, copy to Repeater Device 4
No change, copy to Repeater Device 4
No change, copy to Repeater Device 4
Operating Mode
System > Operating Mode Operating Mode AP Mode
16 of 18 Technical Support Guide
© NetComm Wireless 2017
Location Parameter New Value
General Settings
AP > General
Band
Protocol
Channel Width
Channel
No change, copy to Repeater Device 4
No change, copy to Repeater Device 4
No change, copy to Repeater Device 4
No change, copy to Repeater Device 4
VAP Configuration
AP > VAP Config ESSID No change, copy to Repeater Device 4
Security Settings
AP > Security
Pre-shared Key Type
Pre-shared Key
Passphrase
No change, copy to Repeater Device 4
Repeater Settings
AP > Repeater
Repeater Type No change, copy to Repeater Device 4
WDS Profile* 1. Select WDS Link 2 from the drop-down list,
2. Enter the MAC address of Repeater Device 4
into the Remote AP MAC Address field, see
below.
WDS Enable
Remote AP MAC Address * Enter the MAC address of Repeater Device 4.
Security Type
Cipher Suite
Pre-shared Key Type
Pre-shared Key
No change, copy to Repeater Device 4
No change, copy to Repeater Device 4
No change, copy to Repeater Device 4
No change, copy to Repeater Device 4
* This will be the second WDS Profile for this device, WDS Link 1 will continue to be the AP’s MAC address.
2 . Changes to Configuration of Repeater Device 4
The following parameters in Repeater Device 4 need new values (many can be copied from Repeater Device 3):
Location Parameter New Value
Network Settings
System > Network Interface
IP Address
Netmask
Default Gateway
Primary DNS Server
192.168.20.250
255.255.255.0
192.168.20.1
192.168.20.1
Operating Mode
System > Operating Mode Operating Mode AP Mode
General Settings
AP > General
Band
Protocol
Channel Width
Channel
Must match the other devices in the WDS.
802.11g+802.111n Pure 11n
Must match the other devices in the WDS.
Must match the other devices in the WDS.
VAP Configuration
Configuring NP731 in WDS mode 17 of 18 © NetComm Wireless 2017
Location Parameter New Value
AP > VAP Config ESSID Must match the other devices in the WDS.
Security Settings
AP > Security
Pre-shared Key Type
Pre-shared Key
Passphrase
Must match the other devices in the WDS.
Repeater Settings
AP > Repeater
Repeater Type Must match the other devices in the WDS. (WES)
WDS Profile** 1. Select WDS Link 1 from the drop-down list,
2. Enter the MAC address of Repeater Device 2
into the Remote AP MAC Address field, see
below.
WDS Enable
Remote AP MAC Address
**
Enter the MAC address of Repeater Device 2.
Security Type
Cipher Suite
Pre-shared Key Type
Pre-shared Key
Must match the other devices in the WDS.
Must match the other devices in the WDS.
Must match the other devices in the WDS.
Must match the other devices in the WDS.
** The linking Repeater Device 2 is the only WDS Profile for this device: WDS Link 1
There is no need for the AP device to be added as a WDS Profile.
3. Changes to Access Point (AP) Device
No changes are required to the AP device’s settings.