webinar “abb-tacteo knx access control”€¦ · 25/09/2019 · typical application: hotel...

Webinar “ABB-tacteo KNX Access Control”Diego Carzaniga – Global Product Manager Access Control

SEPTEMBER 2019

Webinar “ABB-tacteo KNX Access Control”

September 25, 2019

Slide 2

Agenda

Overview

Tacteo Access Control Range

Software “MiniMAC”

System Architecture

Access Control References

1004

Webinar “ABB-tacteo KNX Access Control”Overview

Segmentation


September 25, 2019

Slide 4

Needs & trends in different market segments

• Hotels and hospitality

• Main need is guest management and comfort

• Energy Efficiency is an important trend, becoming more and more strategic

• Banks, factories, other tertiary

• Main need is security: the goal is granting centralized and controlled management of access to common and/or reserved areas

http://www.google.it/url?sa=i&rct=j&q=nerocubo+hotel&source=images&cd=&cad=rja&docid=ePtcccVcTrOuZM&tbnid=Yuwyp9_f3PtSbM:&ved=0CAUQjRw&url=http://www.travelblog.it/post/9206/nerocubo-il-nuovo-design-hotel-a-rovereto&ei=tRWCUaWNLsSVPYLTgbAE&bvm=bv.45921128,d.bGE&psig=AFQjCNFEkcLuSgR-t82mABIp7vWp2hRang&ust=1367566052242917

http://www.google.it/url?sa=i&rct=j&q=nerocubo+hotel&source=images&cd=&cad=rja&docid=ePtcccVcTrOuZM&tbnid=Yuwyp9_f3PtSbM:&ved=0CAUQjRw&url=http://www.travelblog.it/post/9206/nerocubo-il-nuovo-design-hotel-a-rovereto&ei=tRWCUaWNLsSVPYLTgbAE&bvm=bv.45921128,d.bGE&psig=AFQjCNFEkcLuSgR-t82mABIp7vWp2hRang&ust=1367566052242917

Energy Efficiency and cost savings


September 25, 2019

Slide 5

• Load activations (lighting, TV) only when guests are inside their rooms

• Smart and optimized management of room heating/cooling (comfort mode activation during check-in operation and when guests are in their rooms; standby/OFF mode activation during check-out and when guests are outsidetheir rooms)

• Access control to services provided by hotels, such as wellness or fitness center

• Access control to hotel common areas (conference rooms, car parking/garage, …)

Energy Efficiency and cost savings

Value-added services

September 25, 2019

Slide 6


The Access Control solution integrated with KNX


September 25, 2019

Slide 7

Access control solution completely integrated into KNX building automation installations

Every access control device installed into a KNX line and communicate with other KNX devices

Commissioning in 2-steps:

1) Programming devices by ETS

2) System configuration by MiniMAC software creating plant, devices configuration (White/black list, time range, extra accesses, …)

Card management, and installation supervision operated by MiniMACsoftware

System architecture


September 25, 2019

Slide 8

MIFARE technology


September 25, 2019

Slide 9

• Tacteo access control transponder reader is based on Mifaretechnology (13.56 MHz), which grants:

• a better security, if necessary, through encryption

• an higher speed when exchanging data

• multi-application, since contactless card used for 13.56 MHz standard (ISO/IEC 14443), typically MIFARE® smartcards, are available with 16 separate memory sectors, that can be used for different applications (not only access control but also payment for example). In this way access control solution can be more easily integrated, when and if necessary, with customer applications and solutions already implemented, or to be implemented

MIFARE technology


September 25, 2019

Slide 10

Access Control

Payment

Tacteo card reader and card holder support standard Mifarecards:

MIFARE Classic 1K EV1

MIFARE UltraLight

Card programmer/reader writes/read into/from the first free memory block of transponder card

Integration with other third-party services/application is easier (they use other memory block in the card for their application)

Integration, when required, is up to the system integrator

Webinar “ABB-tacteo KNX Access Control”The range

Overview and main functionalities

Card reader – TLM/U

September 25, 2019

Slide 12

1 “touch” push-button (+ integrated RGB LED for status icon) for controlling external door-bell

RGB LED for status icons (make-up-room, do-not-disturb)

RGB icon with signaling related to card validation: access allowed/denied

KNX certified device

MiniMAC software needed for programming

1 output channel with 4A@24V relay (for electric lock or courtesy light for example)

Available in 3 dimensions

Flush-mounting installation accordingto worldwide standard (VDE, Swiss, British Standard, NEMA, Italian)

Additional power supply required(12…24 V AC/DC, SELV)


Room Outside Sensor – TA/U

September 25, 2019

Slide 13

This device has the same functionalities of Card reader, but:

It has NOT card reader included (no access control capabilities)

MiniMAC software is NOT needed

Typical application: hotel where access control (or at least ABB Access Control) is not included in the installation but hotel owner/manager wants to have (integrate in one single device):

DND/MUR indication displayed outside room for hotel staff notification

bell capabilities (push-button) outside the room


Room Number + Card reader – TSM/U

September 25, 2019

Slide 14

1 “touch” push-button (+ integrated RGB LED for status icon) for controlling external door-bell

RGB LED for status icons (make-up-room, do-not-disturb)

RGB icon with signaling related to card validation: access allowed/denied




Available in 1 dimension

Flush-mounting installation according to worldwide standard (VDE, Swiss, BritishStandard, NEMA, Italian)


Room Number indication (can be controlled by KNX)


Room Number – TSN/U

September 25, 2019

Slide 15

This device has the same functionalities of Room Number + Card reader, but:

It hasn’t card reader included (no access control capabilities)


Typical application: hotel where access control (or at least ABB Access Control) is not included in the installation but hotel owner/manager wants to have (integrated in one single device):

display of room number outside room (and controlling room number ON/OFF by KNX)

DND/MUR indication displayed outside room for hotel staff notification

bell capabilities (push-button) outside the room

Access Control transponder reader

September 25, 2019

Slide 16

Output configuration

The output of transponder reader can be configured according to two different modalities:

– “Linked to card reader”, receiving in this case switching commands from the device itself (according to transponder card validation). It’s moreover possible to switch the relay according to a standard KNX telegram received from the bus by a KNX device

– Being a standard KNX Switch actuator output, able to be controlled by every KNX-standard devices


September 25, 2019

Slide 17

Output configuration: linked to card reader

Transponder reader output is configured for opening/leaving closed electronic door lock (or courtesy light) while guest card is valid/not valid for access

Transponder reader

(access control)Electric door lock

OUT

4A@24VAC/DC


September 25, 2019

Slide 18

Output configuration: Switch Actuator

Electronic door lock is controlled by an external KNX actuator (SA/S) which receive from access control transponder reader, via KNX bus, information for opening/leaving closed the door

More secure solution, since the relay which controls door can be hided inside the room and not be short-circuited from outside

Transponder reader

(access control) Output freely configurable via

ETS for controlling other load

(for example low voltage LED)

OUT

4A@24VAC/DC

KNX

Electric door lockSA/S

Access Control transponder readerKNX functionalities on card validation

Through 1 bit KNX communication object sent on the bus on card validation event, transponder reader is able to communicate with other KNX devices (for example SA/S) which grants access to room, and activates courtesy light (or moreover they could realize other functions/control other loads)

It’s possible to differentiate behavior between guest and services card validation (some loads activated when guest access the room, some others when staff access the room)

© ABB Group September 25, 2019 | Slide 19

Transponder reader

(access control)

KNX

Electric door lockSA/S

Courtesy light

Staircase light function

Customer (Service)

card valid

(1 bit)

Access Control transponder readerKNX functionalities on card validation

Through 1 byte KNX communication object sent on the bus on card validation event, standard KNX scene can be triggered, for example from one Room Master able to control different kinds of load inside or outside the room

It’s possible to differentiate behavior between guest and services card validation (one scenario activated when guest access the room, one other when staff access the room)


Transponder reader

(access control)

KNX

Electric door lock

RM/S

Room Master

Shutters

Customer (Services)

card valid scene

(1 byte scene)

Courtesy light

Other loads

Access Control transponder readerETS Configuration


Enabling/disabling 8 bit scenes:

On guest card acknowledgment

On service card acknowledgment

Configuring number of Scene to be sent on specific event

Access Control transponder readerETS configuration

Configuring behavior of output (relay)

Normally open/Normally closed contact

Behaviour on bus voltage recovery

Sending status telegram related to switching



Configuring «Output» functionality

Switch Actuator

• the output can be configured as a standard KNX output, freely programmable via ETS with group addresses

• Output is not linked to access control functions (card validation)




Linked to card reader

• the output is linked to access control (relay reacts on transponder card validation)

• Additional functions staircase lighting (Electric lock delay) for courtesy light or electric door lock


Room number (TSN/U) -Card Reader with Room Number (TSM/U)

ETS configuration

In the “Function Block 4” it is possible to configure the behavior of LED related to Room Number signaling, in particular brightness intensity or completely ON/OFF when the devices receive 1-bit telegram (ON/OFF) on the correspondent group object



Card Holder programmable – TKM/U

September 25, 2019

Slide 26

1 “touch” push-button (+ integrated RGB LED for status icon) for setting DND condition

RGB icon with signaling related to card validation: card valid/not valid




Available in 2 dimensions

Flush-mounting installationaccording to worldwide standard (VDE, Swiss, British Standard, NEMA, Italian)


Slot for card insertion

1 “touch” push-button (+ integrated RGB LED for status icon) for setting MUR condition


Card holder “universal” – TKK/U

September 25, 2019

Slide 27

This card holder has the same functionalities of “programmable” Card Holder (KNX functionalities, 1 relay 4A@24V, RGB push-button)

The only difference is represented by card validation scheme/logic:

This “universal” card holder includes MIFARE antenna but without access control capabilities (card validation). This means that every MIFARE card (also not programmed by MiniMAC access control software) is able to activate the relay of the output channel included in the device


Typical application hotel in which Access Control solution (relying on MIFARE technology) is provided by other company (i.e. Vingcard, Salto, …), and ABB could nevertheless offer card holder for guest presence/absence scenes integrated on KNX

Access Control transponder holderOutput configuration

The output of transponder card-holder can be configured according to two different modalities:

– “Linked to card holder”, receiving in this case switching commands from the device itself (according to valid transponder card inserted/removed into/from the card holder)

– Being a standard KNX Switch actuator output, able to be controlled by every KNX-standard devices


Access Control transponder holderOutput configuration: Switch Actuator

Room loads (e.g lights) are controlled by an external KNX actuator (SA/S) which receive from access control transponder holder, via KNX bus, information about switching ON/OFF lights


Transponder holder

(access control) Output freely configurable via

ETS for controlling other load

(for example low voltage LED)

OUT

4A@24VAC/DC

KNX

SA/S

Room light

Access Control transponder holderOutput configuration: linked to card holder

Transponder holder output is configured in order to react on transponder card insertion/removal

Additional loads can be switched ON/OFF on card insertion/removal using proper communication object available


Transponder holder

(access control)

KNX

SA/S

Room lightOUT

4A@24VAC/DC

Socket Outlet

Access Control transponder holder (programmable – TKM/U)KNX functionalities on card insertion/removal

Through 1 bit KNX communication object sent on the bus on card insertion/removal event, transponder holder is able to communicate with other KNX devices (for example SA/S) which activate room loads (e.g. room light, socket outlet)

It’s possible to differentiate behavior between guest and services card validation (some loads activated when guest is inside/outside the room, some others when staff is inside/outside the room)


Transponder holder

(access control)

KNX

SA/S

Delayed OFF

Guest (Service) card

insertion/removal

(1 bit) Socket Outlet

Room light

Delayed OFF

Access Control transponder holder (universal – TKK/U)KNX functionalities on card insertion/removal

Through 1 bit KNX communication object sent on the bus on card insertion/removal event, transponder holder is able to communicate with other KNX devices (for example SA/S) which activate room loads (e.g. room light, socket outlet)


Transponder holder

(access control)

KNX

SA/S

Delayed OFF

Guest (Service) Card

insertion/removal

(1 bit) Socket Outlet

Room light

Delayed OFF

Access Control transponder holder (programmable – TKM/U)KNX functionalities on card insertion/removal

Through 1 byte KNX communication object sent on the bus on card insertion/removal event, standard KNX scene can be triggered, for example from one Room Master able to control different kinds of load inside the room

It’s possible to differentiate behavior between guest and services cards insertion (one scene activated when guest insert/remove cards into/from the card-holder, one other when staff insert/remove cards into/from the card-holder)


Transponder holder

(access control)

KNX

RM/S

Room Master

Shutters

Guest (Services) Card

Removal scene

(1 byte scene)

Guest (Services) Card

Insertion scene

(1 byte scene)

Socket Outlet

Room light

KNX Thermostat Fan coil actuator

Fan-coil

Access Control transponder holder (universal – TKK/U)KNX functionalities on card insertion/removal

Through 1 byte KNX communication object sent on the bus on card insertion/removal event, standard KNX scene can be triggered, for example from one Room Master able to control different kinds of load inside the room


Transponder holder

(access control)

KNX

RM/S

Room Master

Shutters

Guest (Services)

Card Removal scene

(1 byte scene)

Guest (Services)

Card Insertion scene

(1 byte scene)

Socket Outlet

Room light

KNX Thermostat Fan coil actuator

Fan-coil

Access Control transponder holder (programmable – TKM/U)ETS Configuration



On guest card insertion

On service card insertion

On guest card removal

On service card removal


Access Control transponder holder (universal – TKK/U)ETS Configuration



On card insertion

On card removal


Access Control transponder holderETS configuration

Configuring behavior of output (relay)

Normally open/Normally closed contact

Behavior on bus voltage recovery

Sending telegram status for switching




Switch Actuator

• the output can be configured as a standard KNX output, freely programmable via ETS with group addresses

• Output is not linked to access control functions (card insertion/removal)




Linked to card holder

• the output is linked to access control (relay reacts on valid MIFARE transponder card insertion/removal)

• Additional functions delayed OFF (card removal delay)


Webinar “ABB-tacteo KNX Access Control”MiniMAC software

Access ControlNew software MiniMAC 4.1


• Commissioning and configuration of the system

• Simplified and centralized management of hotel functionalities:• Check-in/check-out• Program/delete cards on check-

in/check-out• Room status overview at reception

(dirty clean, minibar to fill, maintenance request, room not usable)

• Access and room occupation history• Interfacing with PMS software (such as

Oracle Fidelio, Protel)

MiniMAC FunctionsCheck-in/Check-out

Wizard for programming/deleting key-card automatically associated to a room number


MiniMAC FunctionsCheck-in/Check-out: creating key-card

It’s possible to specify the kind of card to be created (guest/staff)


MiniMAC FunctionsCheck-in/Check-out: creating key-card

To be filled form with guest/staff data

Customer/staff assigned to groups


MiniMAC FunctionsTransponder card details

Detailed list of transponder card created and their characteristics


MiniMAC FunctionsSpecial cards

It’s possible to create and manage:

– Special card for personnel, in order to notify room status

– Force open (not recommended)


MiniMAC FunctionsGuest and Staff list

Available detailed list of:

– Guests

– Staff


MiniMAC FunctionsRoom heating/cooling

Remote supervision and control (by reception) of room heating/cooling

Configuring heating/cooling supervision linking KNX group addresses (only for compatible thermostats)


MiniMAC FunctionsRoom heating/cooling

Configuring set-point and operating mode

Viewing room temperature

Showing thermostat status (only on models that support it)


MiniMAC FunctionsRoom details

Detailed list of rooms:

– Situation (empty/occupied, make-up-room, cleaned, …)

– Room type (number of rooms, floor, …)


MiniMAC FunctionsAccess history

List of transponder reader and historical data related to access to hotel rooms (which card/user, when)


MiniMAC FunctionsRoom history

List of rooms and historical data on occupation


MiniMAC FunctionsKey-card history

List of transponder card and historical data operations performed (creation, cancellation, …)


MiniMAC FunctionsEvent history

List of all events/operations performed in access control installations by every MiniMAC user


MiniMAC FunctionsEvent management

Visualization and control of events (1-bit) associated to alarms (for example bathroom alarm, technical alarm, fire alarm, …)


MiniMAC FunctionsLoad management

Visualization and control of loads (1-bit) into the installation (for example lighting of common areas, electrical loads, air conditioning, irrigation, …)


MiniMAC FunctionsUsers list

Available detailed list of all users of MiniMAC software

It’s possible to create different users (user/administrator/front office), according to requirements:




• User Administrator: it can access every menu:



• user users has access to the following menus:

Rooms and keys management (all the operations are allowed with the exception of master card (HW key) creation and card delete from database

Supervision (only visualization, no configuration)

Customers and staff (without the possibility to add new MiniMAC user)

History



• user Front Office has access only to the following menu:

Rooms and keys management (only check-in/check-out and solo check-in e check-out and keys list with allowed operation card reading and deleting)

MiniMAC FunctionsSystem Creation and Management

Creation of system architecture and configuration of devices

Available import from ETS function


MiniMAC FunctionsGroups and time-ranges

Access-control guests and staff are organized in groups (at least one existing in the plant)

Time-ranges can be created and associated to groups for every devices, in order to define and managed time-specific authorized access to some room/restricted areas


MiniMAC FunctionsGroup and Extra accesses

In the Extra-Accesses tab, you can specify the list of devices which, for people belonging for the specific group, can be accessed automatically without specifying it at check-in


MiniMAC-PMS InterfaceOverview


ABB PopupPMS ABB

Retrieves from Fidelio/Protel guest check-in data information and automatically fills up the MiniMAC check-in wizard

Check-in operations are performed by Fidelio/Protel which communicates with MiniMAC through a two-clicks Pop-up in the tray bar of the PC

MiniMAC software is necessary (installed in

background) but staff at reception can use only PMS

software (+ ABB Popup)

http://www.micros-fidelio.it/

http://www.micros-fidelio.it/

MiniMAC-PMS InterfaceABB Popup

The PopupClient is usually activated automatically by the service as soon as it detects one or more TAGs to be created.

This screen is only triggered by the service and cannot be recalled at user level. An example of customer TAG creation request is shown below


Webinar “ABB-tacteo KNX Access Control”System architecture

Access ControlMiniMAC

– Tacteo transponder programming devices is a USB Programmer connected only to the PC where MiniMAC is installed

This is a difference compared to Milleniumand Chiara-Mylos access control where the transponder programming device is a KNX device and therefore for programming transponder card, programming device must be connected to KNX bus. For Tacteothis does not happen: the programming device has only to be connected to the PC using USB cable


- Server/PC with MiniMAC installed has to be connected to access control installation

It’s necessary to use KNX IP interface to connect MiniMAC server installation to access control system through KNX bus

Access ControlChoosing transponder cards for Tacteo Access Control

Devices belonging to Tacteo Access Control range are based on MIFARE technology (13,56 MHz)

– Every MIFARE standard card availale on the market can be used with Tacteoaccess control devices. In particular supported cards are:

• MIFARE Classic 1K EV1

• MIFARE UltraLight

ABB includes in the catalogue some MIFARE cards (MIFARE Classic 1K EV1) that are tested specifically with ABB Access Control devices:

– TS/T 1: set of 10 MIFARE transponder cards (order code = 2CSY259412R2041)

– TS/T 1.1: set of 1000 MIFARE transponder cards (order code = 2CSY232175R2041)

– TS/T 1.X: set of MIFARE customized transponder cards (order code = 2CSY232185R2041)


Access ControlMiniMAC

MiniMAC 4.1 software is able to manage configuration and supervision of all access control devices for all ranges included in catalogue:

• Chiara-Mylos (125 KHz)

• Millenium (MIFARE)

• Tacteo (MIFARE)

But please remember that Chiara-Mylos, Millenium and Tacteo are based on different RFID technologies (125 kHZ vs Mifare) and therefore mixed installations are not allowed.

Even Millenium and Tacteo, although both based on MIFARE technology, have different encryption schemes and therefore they can’t coexist in the same installation


Access ControlAdditional Power supply

• All Tacteo access control devices belonging to the range require additional external power supply (12...24V AC/DC, SELV) which allow their working (for example unlocking of electric door lock) also when KNX bus voltage is down

• It’s recommended using a dedicated power supply for electric door lock (not the same used for devices belonging to access control range)

• IMPORTANT it’s forbidden to use for access control devices transformers for discontinuos loads (therefore for example TS and TM from ABB range are not ok since they are used for discontinuous loads, such as doorbell, ...)

• For external supply it’s recommended to use always stabilized SELV power supply

• For dimensioning access control installation in term of transformers/power supply (number and kind) you have to consider that every Tacteo device require 1W peak


ABB Access Control solution

– 1 card reader per room (TLM/U or TSM/U if Room Number variant is needed)

– 1 programmable card-holder per room (TKM/U)

Card reader and card-holder

Month DD, Year | Slide 83© ABB Group

N rooms in a hotel

N x

N x

K common areas in a hotel

– 1 card reader (TLM/U) per every common area required to be controlled with access control (parking,

gym, wellness center, conference room, main entrance, restaurant, …)

K x

ABB Access Control solution

1 USB Programmer (more

than one only if customer clearly request to have different seats for transponder card creation at check-in)

Common devices, accessories and software


1 x

1 MiniMAC 4.1 software license

1 x

> N/10 + K/10

(N = number of roomsK = common areas)

A number of set of 10 MIFARE transponder cards able at least to cover the total number of rooms plus common areas

Third-party Access Control solution

– 1 Room outside sensor per room (TA/U or TSN/U if Room Number variant is needed)

– 1 universal card-holder per room (TKK/U)

Room outside sensor and card-holder


N rooms in a hotel

N x

N x

Access Control Range list of material KNX devices and accessories


• Number of KNX power supply according to standard KNX rules every access control devices requires 10mA from KNX

KNX Power supply KNX Line coupler

• Number of KNX Line coupler (or IP Router) according to number of KNX lines and areas in hotel installation (obviously depending also by total number of other KNX devices installed)

Additional Power supply

(12...24 V AC/DC)

• One Power Supply can be shared among different devices, dimensioning in term of 1W peak absorption from every device

• One KNX IP interface for connecting MiniMAC PC to the KNX bus (needed only for ABB access control installation) KNX IP interface

Webinar “ABB-tacteo KNX Access Control”Overview ranges

Tacteo Access ControlRange overview


Device type Article number Order code Article name Shape

CARD READER (outside the room)

TLM/U.1.1-CG 2CKA006300A1550 Room outside sensor with card reader 86x86



OR

TSM/U.2.1-CG 2CKA006300A1555Room outside sensor with card reader and room number

86x157

CARD HOLDER (inside the room)

TKM/U.1.1-CG 2CKA006300A1553 Card holder programmable 86x86

TKM/U.3.1-CG 2CKA006300A1589 Card holder programmable 115x86

Software, cards, USB

programmer

SW MiniMAC 4.1 2CSY258202R2051 MiniMAC Software -

TP/T 1 2CSY289621R3801 USB MIFARE Programmer -

TS/T 1 2CSY259412R2041 Set of 10 MIFARE transponder cards -

TS/T 1.1 2CSY232175R2041 Set of 1000 MIFARE transponder cards -

Anti-removaldevices

TZE/U.0.2.CK 2CSY245271S3601Anti-removal device for squared, horizontal and Room Number devices (86x86, 115x86, 86x157)

-

TZE/U.0.3.CK 2CSY233741S3611 Anti-removal device for vetical devices (86x115) -

ABB Access Control installation (MiniMAC software)

Tacteo Access ControlRange overview


Device type Article number Order code Article name Shape

Room outsidesensors

(outside the room)

TA/U 3.1.1-CG 2CKA006300A1549 Room outside sensor 86x86



ORTSN/U.2.1-CG 2CKA006300A1603 Room outside sensor with room number 86x157

CARD HOLDER (inside the room)

TKK/U.1.1-CG 2CKA006300A1552 Card holder universal 86x86

TKK/U.3.1-CG 2CKA006300A1588 Card holder universal 115x86

CardsTS/T 1 2CSY259412R2041 Set of 10 MIFARE transponder cards -

TS/T 1.1 2CSY232175R2041 Set of 1000 MIFARE transponder cards -

Anti-removaldevices

TZE/U.0.2.CK 2CSY245271S3601Anti-removal device for squared, horizontal and Room Number devices (86x86, 115x86, 86x157)

-

TZE/U.0.3.CK 2CSY233741S3611 Anti-removal device for vetical devices (86x115) -

TZE/U.0.1.CK 2CKA006300A1633 Anti-removal device for TA/U Room outside sensor

Third-party Access Control installation


September 25, 2019

Slide 105

Training & Qualification Database

In this database you can find the complete online training portfolio for ABB Home and Building Automation

The database includes the following types of training content:

– Application Manuals

– E-Learnings

– Presentations

– Video tutorials

– Webinar slides and videos

www.abb.com/knx or https://go.abb/ba-training

Training and Qualification

Training Database

http://www.abb.com/knx

https://go.abb/ba-training

In addition to the online modules and the traditional training programs offered by your local ABB sales team, we offer a variety of on-site trainings conducted by our specialists at different ABB training facilities

In this Training & Qualification Calendar you can find the educational events that are taking place during 2019

If you are interested in a training please click the training und you will be forwarded to register in “ABB MyLearning”


Training and Qualification

Training Calendar


September 25, 2019

Slide 106

Training & Qualification Calendar




September 25, 2019

Slide 107

KNX Certified Trainings 2019

Certified KNX Courses in Heidelberg

– Basic Course : 21st to 25th October

– Followed by two day application training

And many more training courses in the calendar “International Training Dates 2019”


Certified KNX Basic Course February 2019 in Heidelberg




September 25, 2019

Slide 108

Next Webinar

The topic will be announced …

Wednesday 16th October 2019

– Morning 09:00 am Europe Time (Berlin, UTC + 1h)

– Afternoon 03:00 pm Europe Time (Berlin, UTC + 1h)

Disclaimer

The information in this document is subject to change without notice and should not be construed as a commitment by ABB. ABB assumes no responsibility for any errors that may appear in this document.

In no event shall ABB be liable for direct, indirect, special, incidental or consequential damages of any nature or kind arising from the use of this document, nor shall ABB be liable for incidental or consequential damages arising from use of any software or hardware described in this document.

© Copyright [2019] ABB. All rights reserved.

webinar “abb-tacteo knx access control”€¦ · 25/09/2019 · typical application: hotel...

Documents