welcome everybody!
DESCRIPTION
WELCOME EVERYBODY!. How to make easier our weekdays?. Automatic recording Universal remote controlling Distant access Securty system control Controlling playing devices from PC. For example :. - PowerPoint PPT PresentationTRANSCRIPT
WELCOME WELCOME EVERYBODYEVERYBODY
!!
How to make easier our weekdays?
- Automatic recording- Universal remote controlling- Distant access- Securty system control- Controlling playing devices from PC
For example:For example:
This old woman likes to watching TV, video, she has air conditioner and so many device which need a remote control. But she always conflicting with them, because she has too many remote control.
What will help to her?
CF-MEDIACF-MEDIA
OrOr
TK-124 TK-124 Multimedia Multimedia
remote controlremote control
TK-124 Multimedia Remote control
3 way:
-Automatic mode
-Manual mode
-Learning mode
Connections
Connections Front
Connections Front
System port for appliance configuration: RS 232 Port for CFMC-1 configuration. This
port is used to configurate the CFMC-1 by a PC. The system port also can be used for a remote device which controls the CFMC-1 by RS232.
Ethernet port: This port is often used to connect the programming
PC with the CFMC-1. A TCP/IP device can also be connected to the CFMC-1 by this front port.
Connections Front
LEDS 1
TCP/IP Client status LED:
Status-bar indicators of the IP-Clients. If a red LED is on, the IP-Client is
registered at the CFMC-1. The registration of the TCP/IP port is done in CF
MEDIA Studio in the “Devices” section. For further details please see chapter
5.4. in the CF-MEDIA Studio manual.
+5V status LED:
Power supply status indicator of the CFMC-1.
RF with status LED:
Status indicator for the radio signal. The LED lits when a submitted
radio signal is received
Connections Front
Connections Front
Compact Flash Slot:
You can connect the CF card here.
Connections Front
LEDS 2
CF-Active status LED:
Access Indicator for the Compact Flash card. The blue LED lights on, if access to the data stored on the CF-card is taken.
IR-Learn with status LED:
LED indicator for the active Infra-red learning system. For further information how to learn a IR remote control please see chapter 5.2. in the CF-MEDIA Studio manual.
IRC-Output/Event-Input/RSC-Output status LED:
LED status indicator for the different type of ports. The LEDS lit on when- a command is transferred to an IRC- (red) or RSC- (green) Port - an Event Input is used (yellow LED)
Relay status LED:
Relay control status indicator. A red LED lits on, when a relay is set to “ON” status.
Connections Back
Connections Back
7x COM x (Tx):Up to 7 RSC-controled devices can be
connected to one CFMC-1.Only connect the following pins on the CFMC-1
RSC-port if you want to use a RS-422 connection:
- Pin 4 (TX+)- Pin 5 (GND)- Pin 9 (TX-)
Don’t use fully connected RSC-cables.
1
2
3
4
5
6
7
8
9
1
2
3
4
5
6
7
8
9
Pin configuration RS232
Pin configuration RS422
CFMC-1Device
Connection Feamal- Feamel Cable
Connection Feamel-Male Cable
Connections Back
Connections Back
RTS/CTS: Request To Send (RTS)/ Clear To Send (CTS)
short circuit switch for RS 232/422 Ports. Some RSC-devices use RTS/CTS for connection. RTS/CTS isn’t normally needed. If you put the dip switch to status on and you are using a fully connected cable a bridge between pin 7 (RTS) and 8 (CTS) is established. Dip switch 1 is the dip for the first RSC-port and dip switch 7 is the dip for the seventh RSC-port.
Connections Back
Connections Back
System Port:
The back system configuration port is working like the system port on the front panel. If you have a cable where pin2 and pin3 aren’t crossed you can cross the data lines by switching the dip switches.
Ground Bolt: Ground bolt to connect the CFMC.1 to earth
ground.
Connections Back
Connections Back
12x Relay:
Every CFMC-1 has 12 relay. The relay connection is executed by 2pole connectors. Every relay can hold up to 30 V with a maximum current of 1 A at resistive load.
Be careful to realize a external protection wiring for the relay contacts (flyback diode for DC, RC-combination for AC).
Connections Back
Connections Back
8x IRC-Output:
Every CFMC-1 can be connected with up to eight IR-devices. The infra-red connection is executed by 2pole connectors.
8x Event-Input: Every CFMC-1 has eight event-inputs. The
connection is executed with 2 pole connectors.
Connections Back
Connections Back
Connections Back
RF-Antenna:
Antenna port for KOMTECH 868 MHz radio control system.
DC IN +5V: Power supply for the CFMC-1. The power supply
is executed by an external power supply.
Connections Back
Connecitons Back
3x TCP/IP Ports: There are TCP/IP ports where you can connect - TCP/IP devices - another CF-MEDIA systems - a PC to program a CFMC-1 unit - a PC to transfer data from the PC to a CFMC-1 unit - a Panel which is used a remote for the CFMC-1 unit - a device who just wants to use the integrated network
switch for data transmission in a private network.
What is it good for
?
Or an another example:
How he can solve this
problem?
Only with Only with
CF-MEDIACF-MEDIA
PC
CF-MEDIA
The two things in one piece
UTPCable or RS-232
Thank you for listening us!