welcome to

WELCOME TO

A Company Selling Technology and not just a Product

DCV : DC Volt Meter ACV : AC Volt Meter DCA : DC Current Meter ACA : AC Current Meter DMM-10 : 3 ¾ Digital MultiMeter LAP-C-16032 : 16 Channel PC Based Logic Analyzer DDS-40 : 40MHz DDS Function Generator DSO-100C1G : 100MHz 1GS/s Color Digital Storage

Oscilloscope With FFT TR-1300-1 : 1.3GHz Vector Network Analyzer 304/1 : 3.2GHz Vector Network Analyzer

Products offered by Akademika


DCV

Digital Voltmeter : A voltmeter is an instrument used for measuring electrical potential difference between two points in an electric circuit.

Digital voltmeters give a numerical display of voltage by use of an analog to digital converter.

Digital meters can be made with high accuracy.

Voltmeter accuracy is affected by many factors, including temperature and supply voltage variations.

It measures DC Voltage.


ACV

It is same as the DCV only difference is this measures AC Voltage.


DCA

Digital Current meter: An ammeter is a measuring instrument used to measure the electric current in a circuit.

Instruments used to measure smaller currents, in the milliampere or microampere range, are designated as microammeters or milliammeters.

In much the same way as the analogue ammeter formed the basis for a wide variety of derived meters, including voltmeters, the basic mechanism for a digital meter is a digital voltmeter mechanism, and other types of meter are built around this.


ACA

It is same as the DCV only difference is this measures AC Voltage.


DIGITAL MULTIMETER: A multimeter also known as a VOM (Volt-Ohm meter), is an electronic measuring instrument that combines several measurement functions in one unit.

A typical multimeter would include basic features such as the ability to measure voltage, current and resistance.

Digital multimeters (DMM, DVOM) display the measured value in numerals.

A multimeter can be a hand-held device useful for basic fault finding and field service work, or a bench instrument which can measure to a very high degree of accuracy.

DMM-10


Over current protection Stable voltage and current, low ripple and noise, low drift Pre-setting current limit Selection of series and parallel mode by external switches In series mode, unit can be connected as positive and negative

power output Loop potentiometer makes voltage set easier Four LCD displays indicate voltage and current

PS-303D


LAP-C-16032


Logic based protocol analyzer supports 16 channel. It has portable logic analyzer which supports I2C, UART, SPI, 7-

Segment, arithmetic logic, digital logic, JK Flip flop, up down counter.

Hooks up with bench top tools like oscilloscope etc. Memory 512 Kbits.

FG-20 : Function Generator

• 6 Digit LED display• 30MHz frequency counter internal / external• Attenuator : -20dB, -40dB, -60dB and -20dB variable• DC offset, symmetry continuously adjustable


• Output frequency : 0.2Hz ~ 2MHz • Output waveforms : Sine, square, triangle, ramp pulse,

etc.• Output impedance : 50Ω ± 10%• Output amplitude : ≥ 20Vpp (1MΩ load); >10Vpp (50MΩ

load)• Output attenuation : 0dB / 20dB / 40dB/ 60dB • DC offset : 0 ~ ±10V (1MΩ load); 0 ~ ±5V

(50MΩ load)• Symmetry : 10% ~ 90%


DDS Function Generator

A function generator is usually a piece of electronic test equipment or software used to generate different types of electrical waveforms over a wide range of frequencies.


Some of the most common waveforms produced by the function generator are the sine, square and triangular. These waveforms can be either repetitive or single shot (which requires an internal or external trigger source). Function generators are used in the development, test and repair of electronic equipment.

Function generators cover both audio and RF frequencies, they are suitable for applications that need frequency

stability and high resolution.


DIGITAL STORAGE OSCILLOSCOPE : An oscilloscope is a type of electronic test instrument that allows observation of constantly varying signal voltages as a function of time.

DSO


A storage oscilloscope allows single events to be captured by the instrument and displayed for a relatively long time.

A digital storage oscilloscope is an oscilloscope which stores and analyses the signal digitally rather than using analogue techniques.

It is now the most common type of oscilloscope in use because of the advanced trigger, storage, display and measurement features which it typically provides.

The input analogue signal is sampled and then converted into a digital record of the amplitude of the signal at each sample time.


TR-1300-1

Measurement of S-parameters, impedance, admittance, Quality factor.

Result display format: Smith chart, magnitude and phase, polar diagram, real, imaginary, group delay, VSWR

Characterization of active, passive and lumped DUTS. Analysis capability in time domain and frequency domain Facility to import and export Touchstone files. Intuitive software user interface with direct print facility and post

processing on PC.


304/1


Measurement of S-parameters, impedance, admittance, Quality factor.

Result display format: Smith chart, magnitude and phase, polar diagram, real, imaginary, group delay, VSWR

Characterization of active, passive and lumped DUTS. Analysis capability in time domain and frequency domain Facility to import and export Touchstone files. Intuitive software user interface with direct print facility and post

processing on PC.

AKADEMIKA LAB SOLUTIONSEL-107, MIDC,T.T.C. Electronic Zone, Mahape, Navi Mumbai - 400710.

Tel. : +91 22 27670581/82/83 Fax : +91 22 27670583E-mail : [email protected], Website : www.akademika.in


welcome to

Documents

digital logic

dc voltage

digital voltmeters

digital meters

digital converter

measures ac voltage

digital voltmeter mechanism

electric current