weldfit push-in fittings. for use with weldtube to protect against damage from weld spatter. easy...
TRANSCRIPT
WeldFit Push-in Fittings
WeldFit Push-in Fittings
For use with WeldTube to protect against damage from weld spatter.
Easy tube insertion and removal Tube support for retention under high loads Recessed collet to prevent exposure of inner
tube under side loads Corrosion resistant nickel plated Sizes G1/8, G1/4, G3/8, G1/2
Inner tube 6, 8, 10, 12mm o/d For compressed air or water
WeldFit component parts
Recessed collet Multiple teeth ‘O’ Ring Tube support Body Sealing washer Temperature range
-300C to 700C Materials
Corrosion resistant nickel plated brass componentsNitrile ‘O’ RingPolyamide washer
Tube preparation
WeldFit push-in fittings
Tube preparation
Using a standard tube cutter, cut the complete tube end square at one of the markers.
Ensure that the tube end is clean and free from surface damage
900
Tube preparation
To prevent damage to the inner tube. Use the special stripping tool to cut the outer cover at the next marker
Tube preparation
Push open the tube grip Insert the cut to length tube and line up the next marker
with the blade Close the tube grip and rotate the stripper around the
circumference of the tube
Tube preparation
Push open the tube grip Insert the cut to length tube and line up the next marker
with the blade Close the tube grip and rotate the stripper around the
circumference of the tube
Tube preparation
Push open the tube grip Insert the cut to length tube and line up the next marker
with the blade Close the tube grip and rotate the stripper around the
circumference of the tube
Tube preparation
Next push the blade twist button, this turns the blade 900
Hold the button down and pull the stripper sideways to score the tube to the end
Peal off the outer covering
Tube preparation
Next push the blade twist button, this turns the blade 900
Hold the button down and pull the stripper sideways to score the tube to the end
Peal off the outer covering
Tube preparation
Next push the blade twist button, this turns the blade 900
Hold the button down and pull the stripper sideways to score the tube to the end
Peal off the outer covering
Tube preparation
Next push the blade twist button, this turns the blade 900
Hold the button down and pull the stripper sideways to score the tube to the end
Peal off the outer covering
Tube and fitting assembly
WeldFit push-in fittings
Tube assembly
Push the tube firmly into the collet over the tube support, through the ‘O’ ring and down to the tube stop.
Pull back on the tube to reinforce the collet teeth gripping action
The pressure can then be applied
Tube assembly
Push the tube firmly into the collet over the tube support, through the ‘O’ ring and down to the tube stop.
Pull back on the tube to reinforce the collet teeth gripping action
The pressure can then be applied
Tube assembly
Push the tube firmly into the collet over the tube support, through the ‘O’ ring and down to the tube stop.
Pull back on the tube to reinforce the collet teeth gripping action
The pressure can then be applied
Tube assembly
Push the tube firmly into the collet over the tube support, through the ‘O’ ring and down to the tube stop.
Pull back on the tube to reinforce the collet teeth gripping action
The pressure can then be applied
Tube assembly
Push the tube firmly into the collet over the tube support, through the ‘O’ ring and down to the tube stop.
Pull back on the tube to reinforce the collet teeth gripping action
The pressure can then be applied
Tube removal
WeldFit push-in fittings
Tube removal
Turn off and exhaust the pressure To remove the tube, push the collet in firmly and hold it
there. Pull the tube out and release the collet
Tube removal
Turn off and exhaust the pressure To remove the tube, push the collet in firmly and hold it
there. Pull the tube out and release the collet
Tube removal
Turn off and exhaust the pressure To remove the tube, push the collet in firmly and hold it
there. Pull the tube out and release the collet
Tube removal
Turn off and exhaust the pressure To remove the tube, push the collet in firmly and hold it
there. Pull the tube out and release the collet
The range
WeldFit push-in fittings
WeldFit Push-in Fittings
Included in the range: Straight adaptors Straight connectors Elbow connectors Tee connectors 900 Swivel adaptors 450 Swivel adaptors Banjo assembly range
WeldTube range
Tube range
Four tube sizes each with outer tube colours in a choice of black, blue, green or red.
Inner tube o/d 6,8,10 and 12 mm (4,6,7,9 mm id) Outer tube o/d 8,10,12.5,14.5 mm
Tube range
Minimum recommended bend radius 40, 50, 65 and 75 mm
End