wg's process engineers' codes & standards

7
5/13/2018 WG'sProcessEngineers'Codes&Standards-slidepdf.com http://slidepdf.com/reader/full/wgs-process-engineers-codes-standards-55a7543a81dd0 Process Engineers' Codes & Standards - Prelminary Publisher Code or Standard Comments ABSA Alberta Boilers Safety Association SI units used when provided for in AICHE ANSI K61.1 Safety Requirements for the Storage and Handling of Anhydrous Ammonia ABSA ANSI ANSI API A. @ Interpretations API B. @ Exploration & Production API C. @ Petroleum Measurement (Manual of Petroleum Measurement Standards) API C. Ch ap ter 1, Voc ab ul ar y API C. Chapter 10, Sediment and Water API C. Chapter 11, Physical Properties Data (Volume Correction Factors) API C. Chapter 12, Calculation of Petroleum Quantities API C. Chapter 13, Statistical Aspects of Measuring and Sampling API C. Chapter 14, Natural Gas Fluids Measurement API C. Chapter 15, Guidelines for Use of the International System of Units (SI) in the Petroleum and Allied Industries API C. Chapter 16, Measurement of Hydrocarbon Fluids by Weight or Mass API C. Chapter 17, Marine Measurement API C. Chapter 18, Custody Transfer API C. Chapter 19, Evaporation Loss Measurement API C. Chapter 2, Tank Calibration API C. Chapter 20, Allocation Measurement of Oil and Natural Gas API C. Chapter 21, Flow Measurement Using Electronic Metering Systems API C. Ch ap ter 3, Ta nk Ga ugi ng API C. Chapter 4, Proving Systems meter proving API C. Ch ap ter 5, Met er in g API C. Chapter 6, Metering Assemblies API C. Chapter 7, Temperature Determination API C. Ch ap ter 8, Sampl in g API C. Chapter 9, Density Determination API D. @ Marine Transportation API E. @ Marketing API E. Publ 1612, Guidance Document for Discharging of Petroleum Distribution Terminal Effluents to Publicly Owned Treatment Works API E. Publ 1638, Waste Management Practices for Petroleum Marketing Facilities API F. @ Refining API F.01 @ Inspection of Refining Equipment API F.01 API 510 Pressure Vessel Inspection Code: Maintenance Inspection, Rating, Repair & Alteration Rating and rerating qualificatins re API F.01 API 570 Piping Inspection Code: Inspection, Repair, Alteration & Rerating of In-Service Piping Systems API F.02 @ Mechanical Equipment Standards for Refinery Service API F.02 API 615, SoundControl of Mechanical Equipment for Refinery Services ??? old API610 referred to this-wg API F.02 RP 686, Machinery Installation and Installation Design API F.02 Std 610, Centrifugal Pumps for Petroleum, Heavy Duty Chemical and Gas Industry Services API F.02 Std 611, General Purpose Steam Turbines for Petroleum, Chemical, and Gas Industry Services API F.02 Std 612, Special Purpose Steam Turbines for Petroleum, Chemical, and Gas Industry Services, API F.02 Std 616, Gas Turbines for the Petroleum, Chemical and Gas Industry Services API F.02 Std 617, Centrifugal Compressors for Petroleum, Chemical and Gas Industry Services API F.02 Std 618, Reciprocating Compressors for Petroleum, Chemical and Gas Industry Services API F.02 API F.02 API F.02 Std 674, Positive Displacement Pumps—Reciprocating, API F.02 Std 675, Positive Displacement Pumps—Controlled Volume API F.02 Std 676, Positive Displacement Pumps—Rotary API F.02 Std 681, Liquid Ring Vacuum Pumps and Compressors API F.02 Std 682, Shaft Sealing Systems for Centrifugal and Rotary Pumps API F.02 Std 685, Sealless Centrifugal Pumps for Petroleum, Heavy Duty Chemical, and Gas Industry Services Mag drive and canned pumps API F.03 @ Storage Tanks API F.04 @ Pressure Relieving Systems for Refinery Service API F. 04 RP 520 - Si zin g, Sel ec ti on & I nst al la tio n o f Pr es sur e Rel iev ing De vic es in Re fi ner ies , Pa rt II (I ns ta ll at ion ) Part II, 1994 - Installatio API F.04 RP520 - Sizing, Selection & Installation of Pressure Relieving Devices in Refineries, Part II (Installation) Also, ASME Sec VIII, B &PV Co API F.04 RP521 - Guide for Pressure-Relieving & Depressuring Systems Flare Network dP Calcs? API F.04 RP576 - Inspection of Pressure Relieving Devices API F.04 Std 2000, Venting Atmospheric and Low-Pressure Storage Tanks: Nonrefrigerated and Refrigerated API F.04 Std 526, Flanged Steel Pressure Relief Valves API F.04 Std 527, Seat Tightness of Pressure Relief Valves API F.05 @ Piping Component Standards API F.05 API 574 Inspection Practices for Piping System Components API F.05 RP 578, Material Verification Program for New and Existing Alloy Piping Systems Also ASME B31.3 and API 570, no API F.05 RP 591, User Acceptance of Refinery Valves, API F.05 Std 589, Fire Test for Evaluation of Valve Stem Packing API F.05 Std 594, Check Valves: Wafer, Wafer-Lug and Double Flanged Type API F.05 Std 598, Valve Inspection and Testing API F.05 Std 599, Metal Plug Valves—Flanged and Welding Ends, API F.05 Std 600, Steel Gate Valves—Flanged and Butt-Welding Ends, Bolted and Pressure Seal Bonnets API F.05 Std 602, Compact Steel Gate Valves—Flanged, Threaded, Welding, and Extended Body Ends API F.05 Std 603, Class 150, Cast, Corrosion-Resistant, Flanged-End Gate Valves API F.05 Std 607, Fire Test for Soft-Seated Quarter-Turn Valves API F.05 Std 608, Metal Ball Valves—Flanged, Threaded and Butt-Welding Ends Std 619, Rotary-Type Positive Displacement Compressors for Petroleum, Chemical, and Gas Industry Services Std 672, Packaged, Integrally Geared Centrifugal Air Compressors for Petroleum, Chemical, and Gas Industry Services

Upload: sankara-narayanan

Post on 16-Jul-2015

192 views

Category:

Documents


0 download

TRANSCRIPT

Page 1: WG's Process Engineers' Codes & Standards

5/13/2018 WG's Process Engineers' Codes & Standards - slidepdf.com

http://slidepdf.com/reader/full/wgs-process-engineers-codes-standards-55a7543a81dd0

Process Engineers' Codes & Standards - Prelminary

Publisher Code or Standard CommentsABSA Alberta Boilers Safety Association SI units used when provided for in

AICHE

ANSI K61.1 Safety Requirements for the Storage and Handling of Anhydrous Ammonia ABSA

ANSI

ANSI

API A. @ Interpretations

API B. @ Exploration & Production

API C. @ Petroleum Measurement (Manual of Petroleum Measurement Standards)

API C. Chapter 1, Vocabulary

API C. Chapter 10, Sediment and Water 

API C. Chapter 11, Physical Properties Data (Volume Correction Factors)

API C. Chapter 12, Calculation of Petroleum Quantities

API C. Chapter 13, Statistical Aspects of Measuring and Sampling

API C. Chapter 14, Natural Gas Fluids Measurement

API C. Chapter 15, Guidelines for Use of the International System of Units (SI) in the Petroleum and Allied Industries

API C. Chapter 16, Measurement of Hydrocarbon Fluids by Weight or Mass

API C. Chapter 17, Marine Measurement

API C. Chapter 18, Custody Transfer 

API C. Chapter 19, Evaporation Loss Measurement

API C. Chapter 2, Tank Calibration

API C. Chapter 20, Allocation Measurement of Oil and Natural GasAPI C. Chapter 21, Flow Measurement Using Electronic Metering Systems

API C. Chapter 3, Tank Gauging

API C. Chapter 4, Proving Systems meter proving

API C. Chapter 5, Metering

API C. Chapter 6, Metering Assemblies

API C. Chapter 7, Temperature Determination

API C. Chapter 8, Sampling

API C. Chapter 9, Density Determination

API D. @ Marine Transportation

API E. @ Marketing

API E. Publ 1612, Guidance Document for Discharging of Petroleum Distribution Terminal Effluents to Publicly Owned Treatment Works

API E. Publ 1638, Waste Management Practices for Petroleum Marketing Facilities

API F. @ Refining

API F.01 @ Inspection of Refining Equipment

API F.01 API 510 Pressure Vessel Inspection Code: Maintenance Inspection, Rating, Repair & Alteration Rating and rerating qualificatins re

API F.01 API 570 Piping Inspection Code: Inspection, Repair, Alteration & Rerating of In-Service Piping Systems

API F.02 @ Mechanical Equipment Standards for Refinery Service

API F.02 API 615, SoundControl of Mechanical Equipment for Refinery Services ??? old API610 referred to this-wg

API F.02 RP 686, Machinery Installation and Installation Design

API F.02 Std 610, Centrifugal Pumps for Petroleum, Heavy Duty Chemical and Gas Industry Services

API F.02 Std 611, General Purpose Steam Turbines for Petroleum, Chemical, and Gas Industry Services

API F.02 Std 612, Special Purpose Steam Turbines for Petroleum, Chemical, and Gas Industry Services,

API F.02 Std 616, Gas Turbines for the Petroleum, Chemical and Gas Industry Services

API F.02 Std 617, Centrifugal Compressors for Petroleum, Chemical and Gas Industry Services

API F.02 Std 618, Reciprocating Compressors for Petroleum, Chemical and Gas Industry Services

API F.02

API F.02

API F.02 Std 674, Positive Displacement Pumps—Reciprocating,

API F.02 Std 675, Positive Displacement Pumps—Controlled VolumeAPI F.02 Std 676, Positive Displacement Pumps—Rotary

API F.02 Std 681, Liquid Ring Vacuum Pumps and Compressors

API F.02 Std 682, Shaft Sealing Systems for Centrifugal and Rotary Pumps

API F.02 Std 685, Sealless Centrifugal Pumps for Petroleum, Heavy Duty Chemical, and Gas Industry Services Mag drive and canned pumps

API F.03 @ Storage Tanks

API F.04 @ Pressure Relieving Systems for Refinery Service

API F.04 RP520 - Sizing, Selection & Instal lation of Pressure Relieving Devices in Refineries, Part II (Installation) Part II, 1994 - Instal latio

API F.04 RP520 - Sizing, Selection & Installation of Pressure Relieving Devices in Refineries, Part II (Installation) Also, ASME Sec VIII, B &PV Co

API F.04 RP521 - Guide for Pressure-Relieving & Depressuring Systems Flare Network dP Calcs?

API F.04 RP576 - Inspection of Pressure Relieving Devices

API F.04 Std 2000, Venting Atmospheric and Low-Pressure Storage Tanks: Nonrefrigerated and Refrigerated

API F.04 Std 526, Flanged Steel Pressure Relief Valves

API F.04 Std 527, Seat Tightness of Pressure Relief Valves

API F.05 @ Piping Component Standards

API F.05 API 574 Inspection Practices for Piping System ComponentsAPI F.05 RP 578, Material Verification Program for New and Existing Alloy Piping Systems Also ASME B31.3 and API 570, no

API F.05 RP 591, User Acceptance of Refinery Valves,

API F.05 Std 589, Fire Test for Evaluation of Valve Stem Packing

API F.05 Std 594, Check Valves: Wafer, Wafer-Lug and Double Flanged Type

API F.05 Std 598, Valve Inspection and Testing

API F.05 Std 599, Metal Plug Valves—Flanged and Welding Ends,

API F.05 Std 600, Steel Gate Valves—Flanged and Butt-Welding Ends, Bolted and Pressure Seal Bonnets

API F.05 Std 602, Compact Steel Gate Valves—Flanged, Threaded, Welding, and Extended Body Ends

API F.05 Std 603, Class 150, Cast, Corrosion-Resistant, Flanged-End Gate Valves

API F.05 Std 607, Fire Test for Soft-Seated Quarter-Turn Valves

API F.05 Std 608, Metal Ball Valves—Flanged, Threaded and Butt-Welding Ends

Std 619, Rotary-Type Positive Displacement Compressors for Petroleum, Chemical, and Gas Industry Services

Std 672, Packaged, Integrally Geared Centrifugal Air Compressors for Petroleum, Chemical, and Gas Industry Services

Page 2: WG's Process Engineers' Codes & Standards

5/13/2018 WG's Process Engineers' Codes & Standards - slidepdf.com

http://slidepdf.com/reader/full/wgs-process-engineers-codes-standards-55a7543a81dd0

Process Engineers' Codes & Standards - Prelminary

Publisher Code or Standard CommentsAPI F.05 Std 609, Butterfly Valves: Double Flanged, Lug- and Wafer-Type

API F.06 @ Electrical Installations and Equipment

API F.06

API F.06

API F.06 Std 541, Form-Wound Squirrel-Cage Induction Motors—250 Horsepower and Larger 

API F.07 @ Heat Transfer Equipment Standards for Refinery Service

API F.07 Publ 534, Heat Recovery Steam Generators

API F.07 Publ 535, Burners for Fired Heaters in General Refinery Services

API F.07 RP 531M, Measurement of Noise from Fired Process Heaters

API F.07 RP 536, Post Combustion NOx Control for Equipment in General Refinery Services

API F.07 RP 573, Inspection of Fired Boilers and Heaters

API F.07 Std 530, Calculation of Heater Tube Thickness in Petroleum Refineries

API F.07 Std 560, Fired Heaters for General Refinery Services

API F.07 Std 660, Shell-and-Tube Heat Exchangers for General Refinery Services particularly flating head andr U

API F.07 Std 661, Air-Cooled Heat Exchangers for General Refinery Service

API F.07

API F.07 Std 662, Plate Heat Exchangers for General Refinery Services

API F.08 @ Instrumentation and Control Manuals

API F.08 API 555, Process Analyzers

API F.08 RP 551, Process Measurement Instrumentation Installation procedures for comm

API F.08 RP 552, Transmission Systems Re electroinic and pneumatic c

API F.08 RP 553, Refinery Control Valves

API F.08 RP 554, Process Instrumentation and Control Not a procurment spec

API F.08 RP 556, Fired Heaters & Steam Generators

API F.08 RP 557, Guide to Advanced Control Systems Implementation & owenership, 2

API F.09 @ Technical Data Book Petroleum Refining Prpoerties data for simulati

API F.10 @ Characterization and Thermodynamics (of petroleum fractions)

API F.11 @ Material Engineering Publications

API F.11 Publ 935, Thermal Conductivity Measurement Study of Refractory Castables

API F.11 Publ 939, Research Report on Characterization and Monitoring of Cracking in Wet H2 S Service

API F.11 Publ 946, The Effect of Outgassing Cycles on the Hydrogen Content in Petrochemical Reactor-Vessel Steels

API F.11 Publ 950, Survey of Construction Materials and Corrosion in Sour Water Strippers

API F.11

API F.11 RP 936, Refractory Installation Quality Control Guidelines

API F.11API F.11 RP 945, Avoiding Environmental Cracking in Amine Units

API F.12 @ Petroleum Products and Petroleum Product Surveys

API F.12 Publ 4261, Alcohols and Ethers: A Technical Assessment of Their Application as Fuels and Fuel Components

API F.12 Std 1512, Petroleum Test Laboratory Accreditation Program

API F.13 @ Health, Environment and Safety

API F.13 Publ 421, Management of Water Discharges: Design and Operation of Oil-Water Separators

API F.13

API F.13

API F.13 Publ 958, Pilot Studies on the Toxicity of Effluents from Conventional and Carbon Enhanced Treatment of Refinery Wastewater-Phase III

API F.13 RP 751, Safe Operation of Hydrofluoric Acid Alkylation Units

API F.14 @ Market Data and Statistics

API G. @ Safety and Fire Protection

API G.01 @ Publications

API G.01 Pub 2378, 1999 Summary of Occupational Injuries, Illnesses and Fatalities in the Petroleum Industry

API G.01 Publ 2009, Safe Welding and Cutting Practices in Refineries, Gasoline Plants, and Petrochemical Plants

API G.01 Publ 2028, Flame Arresters in Piping Systems

API G.01 Publ 2030, Application of Water Spray Systems for Fire Protection in the Petroleum Industry

API G.01 Publ 2201, Procedures for Welding or Hot Tapping on Equipment in Service

API G.01 Publ 2214, Spark Ignition Properties of Hand Tools

API G.01 Publ 2216, Ignition Risk of Hydrocarbon Vapors by Hot Surfaces in the Open Air 

API G.01 Publ 2217A, Guidelines for Work in Inert Confined Spaces in the Petroleum Industry

API G.01 Publ 2219, Safe Operation of Vacuum Trucks in Petroleum Service

API G.01

API G.01

API G.01

API G.01 RP 2001, Fire Protection in Refineries

API G.01 RP 2003, Protection Against Ignitions Arising Out of Static, Lightning, and Stray Currents

API G.01 RP 2210, Flame Arresters for Vents of Tanks Storing Petroleum Products

API G.01 RP 2220, Improving Owner and Contractor Safety PerformanceAPI G.01 RP 2221, Manager’s Guide to Implementing a Contractor Safety Program

API G.01 RP 750, Management of Process Hazards

API G.01

API G.02 @ Storage Tank Safety Standards

API G.02

API G.02 Publ 2021A, Interim Study—Prevention and Suppression of Fires in Large Aboveground Atmospheric Storage Tanks

API G.02 Publ 334, A Guide to Leak Detection for Aboveground Storage Tanks

API G.02 RP 2350, Overfill Protection for Storage Tanks in Petroleum Facilities

API G.02 Std 2015, Safe Entry and Cleaning of Petroleum Storage Tanks

API H. @ Storage Tanks

API H. Air Emissions from Aboveground Storage Tanks Manual

API H. Bull 2521, Use of Pressure-Vacuum Vent Valves for Atmospheric Loss

,

,

Std 662, Plate Heat Exchanger Specification Sheets in Electronic Format, Plate Heat Exchangers for General Refinery Services

, - - -

RP 941, Steels for Hydrogen Service at Elevated Temperatures and Pressures in Petroleum Refineries and Petrochemical Plants

Publ 422, Groundwater Protection Programs for Petroleum Refining and Storage Facilities: A Guidance Document

Publ 800, Literature Survey: Subsurface and Groundwater Protection Related to Petroleum Refinery Operations

Publ 2510A, Fire Protection Considerations for the Design and Operation of Liquefied Petroleum Gas (LPG) Storage Facilities, —

Publ 770, A Manager’s Guide to Reducing Human Errors; Improving Human Preformance in the Process Industries

RP 752, Management of Hazards Associated With Location of Process Plant Buildings, CMA Manager’s Guide

Publ 2021, Fighting Fires In and Around Flammable and Combustible Liquid Atmospheric Petroleum Storage Tanks

Page 3: WG's Process Engineers' Codes & Standards

5/13/2018 WG's Process Engineers' Codes & Standards - slidepdf.com

http://slidepdf.com/reader/full/wgs-process-engineers-codes-standards-55a7543a81dd0

Process Engineers' Codes & Standards - Prelminary

Publisher Code or Standard CommentsAPI H. Chapter 19.1, Evaporative Loss From Fixed Roof Tanks

API H. Chapter 19.1A, Evaporation Loss from Low-Pressure Tanks

API H. Chapter 19.4, Recommended Practice for Speciation of Evaporative Losses

API H.

API I. @ Valves

API I. RP 591, User Acceptance of Refinery Valves,

API I. Std 594, Check Valves: Wafer, Wafer-Lug and Double Flanged Type

API I. Std 598, Valve Inspection and Testing

API J. @ Industry Training

API J. Publ 1200E, Electronic Curriculums Manager for Federally Mandated Training and Information

API K. @ Health and Environmental Issues

API K.01 @ Air Research

API K.01 Publ 335, Refinery MACT Workshop Manual Maximum achievable control tech

API K.02 @ Environment and Safety Data

API K.03 @ Human Health Related Research

API K.04 @ Natural Resource Damage Assessment

API K.05 @ Pollution Prevention

API K.05

API K.05 Publ 302, Waste Minimization in the Petroleum Industry: A Compendium of Practices

API K.06 @ Soil and Groundwater Research

API K.07 @ Environmental Stewardship Program PublicationsAPI K.08 @ Storage Tank Research

API K.09 @ Surface Water Research

API K.09 DR 351, Proceedings: Workshop to Identify Promising Technologies for the Treatment of Produced Water Toxicity Offshore exploration

API K.09 Publ 4602, Minimization, Handling, Treatment and Disposal of Petroleum Products Terminal Wastewaters

API K.09 Publ 4606, Source Control and Treatment of Contaminants Found in Petroleum Product Terminal Tank Bottoms

API K.09 Publ 4610, Critical Review of Draft EPA Guidance on Assessment and Control of Bioconcentratable Contaminants in Surface Waters

API K.09 Publ 4633, Barium in Produced Water: Fate and Effects in the Marine Environment

API K.09 Publ 4663, Remediation of Salt-Affected Soils at Oil and Gas Production Facilities

API K.09 Publ 4666, The Toxicity of Common Ions to Freshwater and Marine Organisms

API K.09 Publ 4676, Arsenic: Chemistry, Fate, Toxicity, and Wastewater Treatment Options

API K.09 Publ 4688, Temporary Treatment Options for Petroleum Distribution Terminal Wastewaters

API K.09 Publ 4694, Laboratory Analysis of Petroleum Industry Wastewaters

API K.09 Publ 4695, Understanding and Preparing Applications for Petroleum Facility NPDES Discharge Permits National pllutant discharge elimination syste

API K.09

API K.10 @ Waste Research

API L. @ Subscriptions and Information Technology Products

API M. @ Policy and Economic Studies

API N. @ Public Affairs and Information

API O. @ Out of Print Publications

ASA

ASME A112 "Plumbing, flor and roof drains" etc

ASME A120.1 Safety Requirements for Powered Platforms for Buidling Maintenance

ASME A13.1 Scheme for the Identification of Piping Systems (Identifying piping contents & hazards therof, etc)

ASME A17 "Elevators & Escalators" etc

ASME A18 Safety Standard for Platform Lifts & Stairway Chairlifts

ASME A90 .1 Safety Standard for Belt Manlifts

ASME AG-1 Code on Nuclear Air & Gas Treatment

ASME B1 "Screw Threads" etc

ASME B107 "Hammers and other tools" etcASME B133 .4 Gas Turbine Control & Protection Systems

ASME

ASME B133.11 Procurement Standard for Gas Turbine Preparation for Shipping & Installation

ASME B133.16 Procurement Standard for Gas Turbine Marine Applications

ASME B133.2 Procurement Standard for Gas Turbine Maintenance & Safety

ASME B133.3 Procurement Standard for Gas Turbine Auxiliary Equipment

ASME B133.7M Gas Turbine Fuels

ASME B133.8 Gas Turbine Installation Sound Emissions

ASME B133.9 Measurement of Exhaust Emissions from Stationary Gas Turbine Engines

ASME B15 .1 Safety Standard for Mechanical Power Transmission Apparatus

ASME B16 Fittings, flanges and gas valves (eg: AMSE B16.34 - Control valves?)

ASME B17 Keys & Keyseats

ASME B18 Fasteners (Rivets, nuts, bolts, etc)

ASME B19 Safety Standard for Air Compressor Systems & Compressors for Process IndustriesASME B20 Safety Standard for Conveyors & Related Equipment

ASME B27 Retaining Rings

ASME B29 "Chains & Sprockets" etc

ASME B30 Lifting Devices

ASME B31 Codes for Pressure Piping Also adopted by CSA

ASME B31.1 Power Piping (Power Boilers & Auxiliaries >15 psig, or, water >160 psig or 250F)

ASME B31.11 Slurry Transportation Piping Systems

ASME B31.2 Fuel Gas Piping Steam & industrial buildings

ASME B31.3 Process Piping (was previously called Petroleum Refinery Piping)

ASME B31.4 Pipline Transportation Systems for Liquid Hydrocarbons & Other Liquids X country

ASME B31.5 Refrigeration Piping & Heat Transfer Components

Publ 2557, Vapor Collection and Control Operations for Storage and Transfer Operations in the Petroleum Industry

Publ 300, The Generation and Management of Waste and Secondary Materials in the Petroleum Refining Industry

,

B133.10 Procurement Standard for Gas Turbine Information to be Supplied by User and Manufacturer 

Page 4: WG's Process Engineers' Codes & Standards

5/13/2018 WG's Process Engineers' Codes & Standards - slidepdf.com

http://slidepdf.com/reader/full/wgs-process-engineers-codes-standards-55a7543a81dd0

Process Engineers' Codes & Standards - Prelminary

Publisher Code or Standard CommentsASME B31.6 Chemical Plant Al fluids in chemical plant

ASME B31.7 Nuclear  

ASME B31.8 Gas Tranmission & Distribution Piping Systems CSA Z184

ASME B31.9 Building Services

ASME B32 "Wire & Products Other than Pipe" etc

ASME B36.10M Welded & Seamless Wrought Steel Pipe

ASME B36.19M Stainless Steel Pipe

ASME B4 "Tolerances, Limits and Fits" etc

ASME B40 "Thermomoters, seals, snubbers, limiter valves" etc

ASME B46.1 Surface Texture

ASME B47.1 Gage Blanks

ASME B5 "Machine Tools" etc

ASME B56 "Industrial trucks, forklifts" etc

ASME B73.1M Specification for Horizontal End Suction Centrifugal Pumps for Chemical Process

ASME B73.2M Specification for Vertical In-Line Centrifugal Pumps for Chemical Process

ASME B73.3M Specification for Sealless Horizontal End Suction Centrifugal Pumps for Chemical Process

ASME

ASME B89 "General Dimensional Measurement" etc

ASME B89 Power Boilers Section (betz video tape)

ASME B94 "Dies & Cutting Tools" etc

ASME B96.1 Welded Aluminum-Alloy Storage Tanks

ASME BPE Bioprocessing Equipment

ASME BPVC Addenda Annual additions and revisions

ASME BPVC Code Cases Verifies code intent, provide urgent

ASME BPVC Interpretations

ASME BPVC Sec I Rules for Construction of Power Boilers 1998?

ASME BPVC Sec II Materials, Parts A,B,C,D

ASME BPVC Sec III Subsection NCA, Div 1,2,3

ASME BPVC Sec IV Rules for Construction of Heating Boilers

ASME BPVC Sec IX Welding and Brazing Qualifications

ASME BPVC Sec V Nondestructive Examination

ASME BPVC Sec VI Recommended Rules for the Care & Operation of Heating Boilers

ASME BPVC Sec VII Recommended Rules for the Care & Operation of Power Boilers

ASME BPVC Sec VIII Rules for Construction of Pressure Vessels, Div 1,2,3

ASME BPVC Sec X Fiber-Reinforced Plastic Pressure VesselsASME CSD Manufacturer's Installing Contractor's Reports for ASME

ASME CSD-1 Control & Safety Devices for Automatically Fired Boilers

ASME FAP "QA Program … Fasteners" etc

ASME HPS High Pressure Systems Augments BPVC and B31.1

ASME HST Air Chain Hoists, etc

ASME MFC "Measurement of Fluid Flow in Pipes", etc (eg: ASME MFC-3M)

ASME MH1 "Pallets"

ASME N278 Self-Operated and Power-Operated Safety-Related Valves Functional Specificatoin Standard For application in nuclear power p

ASME N509 Nuclear Power Plant Air Cleaning Units & Components

ASME N510 Testing of Nuclear Air Treatment Systems

ASME N626 Qualifications & Duties of Specialized Professional Engineers Certifications for owner, etc

ASME NOG "Gantry Cranes"

ASME NQA "QA for nuclear facilities" etc

ASME NUM "Cranes, Monorails" etc

ASME OM "Standards, Guides and Code for the Operation & Maintenance of Nuclear Power Plants", etc

ASME PALD Safety Standard for Portable Automotive Lifting Devices

ASME PTC 1 General Instructions

ASME PTC 10 Test Code on Compressors & Exhausters

ASME PTC 11 Fans

ASME PTC 12.1 Closed Feedwater Heaters

ASME PTC 12.2 Steam Surface Condensers

ASME PTC 12.3 Deaerators

ASME PTC 18 Hydraulic Turbines

ASME PTC 18.1 Pumping Mode of Pump/Turbines

ASME PTC 19.1 Measurement Uncertainty

ASME PTC 19.10 Flue and Exhaust Gas Analysis

ASME PTC 19.11 Steam & Water Sampling, Conditioning and Analysis in the Power Cycle

ASME PTC 19.2 Pressure Measurement

ASME PTC 19.22 Digital Systems TechniquesASME PTC 19.23 Guidance Manual for Model Testing

ASME PTC 19.5 Application Part II of Fluid Meters: Interim Supplement to PTC 19.5 on Instruments and Apparatus

ASME PTC 19.5.1 Weighing Scales

ASME PTC 19.7 Measurement of Shaft Power 

ASME PTC 19.8 Measurement of Indicated Power 

ASME PTC 20.1 Speed and Load-Governing Systems for Steam turbine-Generator Units

ASME PTC 20.2 Overspeed Trip Systems of Steam Turbine-Generator Units

ASME PTC 20.3 Pressure Control Systems Used on Steam Turbine Generator Units

ASME PTC 21 Particulate Matter Collection Equipment

ASME PTC 22 Performance Test Code on Gas Turbines

B73.5M Thermoplastic/Thermoset Polymer Material Horizontal End Suction Centrifugal Pumps for Chemical Process

r en rep es o nqu res, yp ca yannual

Page 5: WG's Process Engineers' Codes & Standards

5/13/2018 WG's Process Engineers' Codes & Standards - slidepdf.com

http://slidepdf.com/reader/full/wgs-process-engineers-codes-standards-55a7543a81dd0

Process Engineers' Codes & Standards - Prelminary

Publisher Code or Standard CommentsASME PTC 23 Atmospheric Water Cooling Equipment Forced and natural draft cooling tow

ASME PTC 24 Ejectors

ASME PTC 25 Pressure Relief Devices

ASME PTC 28 Determining the Properties of Fine Particulate Matter 

ASME PTC 29 Speed Governing Systems for Hydraulic Turbine Generator Units

ASME PTC 3.1 Diesel & Burner Fuels

ASME PTC 3.2 Solid FuelsASME PTC 3.3 Gaseous Fuels

ASME PTC 30 Air Cooled Exchangers

ASME PTC 31 Ion Exchange Equipment

ASME PTC 32.1 Nuclear Steam Supply Systems

ASME PTC 33 Large Incinerators Code & Appendix Package

ASME PTC 33A Abbreviated Incinerator Efficiency Test

ASME PTC 36 Measurement of Industrial Sound

ASME PTC 38 Determining the Concentration of Particulate Matter in a Gas Stream

ASME PTC 39.1 Condensate Removal Devices for Steam Systems

ASME PTC 4 Fired Steam Generators

ASME PTC 4.2 Coal Pullverizers

ASME PTC 4.3 Air Heaters

ASME PTC 4.4 Gas Turbine heat Recovery Steam Generators

ASME PTC 40 Flue Gas Desulfurization UnitsASME PTC 46 Overall Plant Performance

ASME PTC 5 Reciprocating Steam Engines

ASME PTC 6 & 6A Test Code on Steam Turbines

ASME PTC 6S Procedures for Routine Performance Test of Steam Turbines

ASME PTC 7.1 Displacement Pumps

ASME PTC 8.2 Centrifugal Pumps

ASME PTC 9 Displacement Compressors, Vacuum Pumps & Blowers

ASME PTC PM Performance Monitoring Guidelines for Steam Power Plants

ASME PTC12.4 Moisture Separator Reheaters

ASME PVHO-1 Safety Standard for Pressure Vessels for Human Occupancy - eg: submersibles, air locks, etc

ASME QAI Qualifications for Authorized Inspection Nuclear 

ASME QEI Standard for the Qualification of Elevator Inspectors

ASME QHO Standard Qualification and Certification of Hazardous Waste Incinerator Operator 

ASME QME Qualification of Active Mechanical Equipment Nuclear 

ASME QMO Standard for the Qualification and Certification of Medical Waste Incinerator OperatorsASME QRO Standard for the Qualification & Certification of Resource Recovery Facility Operators

ASME QTC GT PowerPlant TestCode?

ASME RTP-1 Reinforced Thermoset Plastic Corrosion Resistant Equipment

ASME Sec XI Rules for Inservice Inspection of Nuclear Power BPVC Plant Components

ASME

ASME STS-1-2000 Steel Stacks

ASME Y14 Acronyms, Mechanical Engineering Drawing Practices, etc

ASME Y32 Graphic Symbols

ASME Y32.1 Graphic Symbols for Process Flow Diagrams in Petroleum and Chemical Industries

ASME Y32.10 Graphic Symbols For Fluid Power Diagrams

ASME

ASME Y32.2.4 Graphic Symbols for Heating, Ventilating and Air Conditioning

ASME Y32.2.6 Graphics Symbols for Heat-Power Apparatus

ASME Y32.4 Graphic Symbols for Plumbing Fixtures for Diagrams Used in Architecture & Building Construction

ASTM

CCME National Emission Guidelines for Stationary Combustion Turbines - Canadian Council of Ministers of the Environment (CCME)

CSA B51.95 Boiler, Pressure Vessel, and Pressure Piping Code ABSA

CSA B51.95 Part 1, Including Appendix I, Automotvie Propane Vessel Standards ABSA

CSA B51.95 Part 2, High Pressure Cylinders for the On-Board Storage of Natural Gas… ABSA

CSA B51.95 Part 3, Requirements for CNG Refuelding Stqation Presure Piping Systems and Ground Storage… ABSA

CSA B52.95 Mechanical Refrigeration Code ABSA

CSA Z662-1994 Oil and Gas Pipeline Systems ABSA

DOT Regulations … Governing the Transportation of Haaardous Materials in Tank Motor Vehicles ABSA

EPA

EPRI

HEI

ISA? S77.14.01 Fossill..ST By Pass Systems

MSS Std Practice SP-25 Standard Marking System for Valves, Fittings, Flanges and Unions ABSA

NACE @ NACE Book of Standards--Hard Copy

NACE RP0182-95 Initial Conditioning of Cooling Water Equipment

NACE RP0189-95 On-Line Monitoring of Cooling Waters

NACE

NACE

NACE

NACE 8/SSPC-SP 14 Industrial Blast Cleaning

NACE 7/SSPC VIS 4 Guide and Visual Reference Photographs for Steel Cleaned by Water Jetting

NACE

NACE NACE/SSPC Joint Standards Package (NACE No 1,2,3,4,5,6,8)

NACE RP0100-2000 Cathodic Protection of Prestressed Concrete Cylinder Pipelines

- -

. . ,

API RP 1632 Cathodic Protection of Underground Petroleum Storage Tanks and Piping Systems -- 1996 Edition

MR0175-2001 Sulfide Stress Cracking Resistant Metallic Materials for Oilfield Equipment

5/SSPC-SP 12 Surface Preparation of Steel and Other Hard Materials by High- and Ultrahigh-Pressure Water Jetting Prior to Recoating

9/SSPC VIS 5 Guide and Reference Photographs for Steel Surfaces Prepared by Wet Abrasive Blast Cleaning

Page 6: WG's Process Engineers' Codes & Standards

5/13/2018 WG's Process Engineers' Codes & Standards - slidepdf.com

http://slidepdf.com/reader/full/wgs-process-engineers-codes-standards-55a7543a81dd0

Process Engineers' Codes & Standards - Prelminary

Publisher Code or Standard CommentsNACE RP0169-96 Control of External Corrosion on Underground or Submerged Metallic Piping Systems

NACE

NACE RP0176-94 Corrosion Control of Steel Fixed Offshore Platforms Associated with Petroleum Production

NACE

NACE RP0181-94 Liquid-Applied Internal Protective Coatings for Oilfield Production Equipment

NACE RP0193-2001 External Cathodic Protection of On-Grade Carbon Steel Storage Tank Bottoms

NACE RP0196-96 Galvanic Anode Cathodic Protection of Internal Submerged Surfaces of Steel Water Storage TanksNACE RP0198-98 The Control of Corrosion Under Thermal Insulation and Fireproofing Materials--A Systems Approach

NACE RP0273-2001 Handling and Proper Usage of Inhibited Oilfield Acids

NACE RP0288-94 Inspection of Linings on Steel and Concrete

NACE RP0292-98 Installation of Thin Metallic Wallpaper Lining in Air Pollution Control and Other Process Equipment

NACE

NACE

NACE RP0298-98 Sheet Rubber Linings for Abrasion and Corrosion Service

NACE RP0387-99 Metallurgical and Inspection Requirements for Cast Sacrificial Anodes for Offshore Applications

NACE RP0375-99 Wax Coating Systems for Underground Piping Systems

NACE RP0388-95 Impressed Current Cathodic Protection of Internal Submerged Surfaces of Steel Water Storage Tanks

NACE

NACE RP0392-2001 Recovery and Repassivation After Low pH Excursions in Open Recirculating Cooling Water Systems

NACE

NACE

NACENACE

NACE

NACE RP0497-97 Field Corrosion Evaluation Using Metallic Test Specimens

NACE RP0575-01 Internal Cathodic Protection Systems in Oil-Treating Vessels

NACE RP0572-2001 Design, Installation, Operation, and Maintenance of Impressed Current Deep Groundbeds

NACE RP0590-96 Recommended Practice for Prevention, Detection, and Correction of Deaerator Cracking

NACE RP0775-99 Preparation and Installation of Corrosion Coupons and Interpretation of Test Data in Oilfield Operations

NACE SPECIALTY PACKAGE: Sulfide Stress Cracking in Oilfield Equipment

NACE SPECIALTY PACKAGE: Cathodic Protection of Pipelines/Tanks

NACE SPECIALTY PACKAGE: Corrosion Control of Equipment Used in Offshore Operations

NACE TM0172-2001 Determining Corrosive Properties of Cargoes in Petroleum Product Pipelines

NACE TM0173-99 Methods for Determining Water Quality for Subsurface Injection Using Membrane Filters

NACE TM0194-94 Field Monitoring of Bacterial Growth in Oilfield Systems

NACE

NACE

NACE

NACE TM0286-2001 Cooling Water Test Unit Incorporating Heat Transfer Surfaces

NACE

NACE TM0397-97 Screening Tests for Evaluating the Effectiveness of Gypsum Scale Removers

NACE TM0399-99 Test Method for Phosphonate in Brine

NACE TM0498-98 Standard Test Method for Measuring the Carburization of Alloys for Ethylene Cracking Furnace Tubes

NEMA

NFPA NFPA 11 Standard on Foam Extinguishing Systems

NFPA NFPA 12 Standard for Carbon Dioxide Extinguishing Systems

NFPA NFPA 13 Standard for the Installation of Sprinkler Systems

NFPA NFPA 14 Standard for the Installtionof Standpipe and Hose Systems

NFPA NFPA 17 Standard for Dry Chemical Extinguishing Systems

NFPA NFPA 20 Standard for the Installation of Centrifugal Fire Pumps

NFPA NFPA 22 Standard for the Installatin of Water Tanks for Private Fire Protection

NFPA NFPA 24 Standard for Outside Protection

NFPA NFPA 58 Standard for the Storage and Handling of Liquefied Petroleum Gases ABSA

OSHA

TEMA Standards of Tubular Exchanger Manufacturers Association ABSA

Standard References and HandbooksISA Handbook of Control Valves

Dow Chemical Gas Conditioning Fact Book

NFPA Handbook of Fire Protection

Handbook of Industrial Loss Prevention, Factory Mutual Engineering Corp

ASME Handbook on Water Technology for Thermal Power systems, 1989

Standard Handbook of Power Plant Engineering, 1989

-

-

- , ,

- , ,

-

- , , - , -

- - , , ,

- -- -

-

-

- --

- -

-

Page 7: WG's Process Engineers' Codes & Standards

5/13/2018 WG's Process Engineers' Codes & Standards - slidepdf.com

http://slidepdf.com/reader/full/wgs-process-engineers-codes-standards-55a7543a81dd0

Process Engineers' Codes & Standards - Prelminary

Publisher Code or Standard Comments

Abbreviations:

ASME = American Society of Mechanical Engineers

ASTM = American Standard Testing Materials?

HEI = Heat Exchange Institute

TEMA = Thermal Exchanger Manufacturers Association?

API = American Petroleum Institute

NACE International = National Association of Corrosion Engineers International

ISA = Instrument Society of America? International Society for Measurement and Control?

CSA = Canadian Standards Association

PTC = Performance Test Code

OSHA = Occupational Safety and Health Administration

ASME "Codes and Standards by Designator Code"

BPVC = AMSE Boiler & Pressure Vessel Code

ASA = American Standards Association (fittings, plumbing etc)

AWWA

AWS (American Welding Society)

ABSA = Alberta Boilers Safety Association

API 610, 1984 said there exists API 5L specification for line pipe ??? Find out about that...

ANSI = American National Standards Institute (works with over 175 organizations to approve their standards) (eg: ANSI has approved many API standards)