whitegoods 20 linear perimeter flush bezel · 2020. 4. 20. · m3 screws x1 x1 1.75" slot width...

3 -

1/8"

3 -

1/8"

M3 Screws

x1

x1

1.75"

slot width

6.0

"

2.0"

4", 6" or 8" Infill Panels

Frame

Fram

e

4.9

"

slot width

x Frame

Fram

e

Housing L-Angle Bracket

Illuminated surface

Square Joiner

Flat JoinerSquare Joiner

Housing

Endcap

Set Screw

Housing

Frame

Fram

e

5/8" Drywall Mudded taper

Frame

Fram

e


M4 Fastener

Frame

Fram

eGear Tray

Gear Tray Screw

3 -

7/8"

1 - 3/4"

5/1

6"

C

Mounting Clip

Mounting Clip (C)

3.0

8

1 - 3/4"

5/1

6" Drill 1/4" Feed Hole 2 -

1/4"

Drill 1/4" Feed Hole


C

A

C

Step 5; Install Housing: Ensure all Low voltage cables are pulled through the wall and accessible. Check that Housings (A) and Luminaires (B) have correct End caps and Joiners installed. Then push the Housing (A) up until it engages with the Mounting Clips (C). Then slide the joiners (example below) halfway in between each Housing (A) and tighten the set screws. Repeat until all Housings (A) are installed. Run Low voltage cable through Housing (A) feed hole. Finally, make electrical connections to Luminaire (B) cables with supplied connectors.

1 - 1/4"

A

FinishedCeiling

BC

B

A

Set Screw

FinishedCeiling

3 -

1/8"

1 - 1/4"

Step 4; Mounting Hardware: Install Endcaps on first and last Housing (A) and Luminaire (B) of each run. Install Joiners on each Housing (A), before putting in the ceiling. Install Snap-in Clips onto Luminaire (B) using providedscrews.

Luminaire Power Cable

YFill in Joiner Slot

Plaster up to "Knife Edge",no farther

Finished Ceiling

Step 2; Feed Holes: Determine which end the Luminaire (B) cables will start at on each Housing (A) and mark them on the shown location on the Housings (A), no less than 3 inches from the end. Then drill 1/4" holes where you marked. Finally look at where the Housings (A) will be installed and drill 1/4" holes above the line of the Mounting Clips, and close to where the holes in the Housings (A) will end up.

A

A


Lens

B

B

Luminarie Power Cable

B

B

B

Phillips Head #2 Screwdriver

Wire Connectors

Wire Strippers

M3 Hex head Allen Key

Mounting Screws

LOCATE AND REVIEW ANY CONSTRUCTION PLANS AND INTERLUX RECORD DRAWINGS FOR ALL FIXTURE RUNS. It is recommended to locate and lay out all components for each fixture "run". A fixture run typically consist of joiners, lengths of housings, lengths of inserts, and endcaps.

BE SURE TO IDENTIFY ALL CORRECT LENGTHS FOR EACH FIXTURE RUN.

Step 2: (If single housing skip this step) Insert joiners into next housing as seen below.Place next housing end to end with first housing, slide joiners across housing seam so they are joining both housings. Secure joiners by tightening set screws. Mount housing. Repeat until all housing are installed and mounted.

Joiner Kit

Step 6: Install Gear Trays making electric connections first then insert gear tray into housing (4" Blank Gear Trays go on ends of each run). Refer to pages 2&3 for wiring diagrams if needed. Refer to record drawings for gear tray placement. Secure gear tray to housing using screws in pre-drilled holes. Repeat this step until all gear trays are installed. Energize and test for proper operation.

Housing

Master Gear Tray with DiffuserSatellite Gear Tray with Diffuser

Infill Panel

L-Angle

Endcaps

Blank Gear Tray (4")

x= slot width + 1.75"

Mounting Screws

Step 4: Attach 5/8" drywall to the underside of the housing. Apply joint tape and mud to form a smooth taper. Apply multiple thin coats to ensure a smooth taper. Prime and paint.

Flat JoinerHousing

Housing (A)

Luminaire (B)

Wood Backing Drywall AnchorOption A

FinishedCeiling

FinishedCeiling


Step 4: Ensure all Low voltage cables are pulled through the wall and accessible. Then install ceiling, leaving a 1 - 3/4" gap for the Housings (A). Ensure Housings have correct End caps and Joiners installed, then run insert power cable through Housing (A) feed hole and make electrical connection to Low voltage wires with supplied connectors. Finally, push Housing (A) up into the slot until it locks into the Mounting Clips and the flange is flush with the bottom of the ceiling.

Joiners

End Caps

Step 5: Ensure all inserts are Repeat this step until all gear trays are installed. Energize and test for proper operation.

Driver Enclosure

1.5 lb/ft1.5 lb/ft

Step 3; Remote Drivers: Install the Remote drivers and run Low voltage cables to the wall. Then run the Low voltage cables through the feed holes drilled above the Mounting Clips (C).

Step 1; Mounting Clips: Turn off Power before Installing. Mark the wall at the intended height of the Mounting Clips (C), 3 - 1/8" above the bottom of the intended ceiling. Then screw Mounting Clips (C) into the wall, it is recommended you use appropriate backing or drywall anchors. The surrounding structure is required to support the weight of the fixture (1 - 1/2 lb per foot). Use at least one Clip every 16", for each Housing (A) Length. For shorter Housings (A), must use at least 2 Clips per Housing (A), 3 recommended. No Clip should be within 3" from the ends of any Housing (A).

Step 6; Install Luminaire: Push the Luminaires (B) up until they snap into the Housings (A). If possible, arrange Luminaire (B) lenses so that they overlap fixture joints. Next, power the Luminaires (B) to double check electrical connections. When the ceiling is installed, it will need to end 1 - 1/4" from the the wall to accomodate the Housings (A).

Snap-inClips

3 -

1/8"

3 -

1/8"

THE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF Inter-lux. ANY REPRODUCTION IN PART OR AS A WHOLE WITHOUT THE WRITTEN PERMISSION OF Inter-lux IS PROHIBITED.

PROPRIETARY AND CONFIDENTIAL

PART NO. WG-20LPF-RBT

Page 1 of 3DRAWING NOT TO SCALE

Whitegoods 20 Linear PerimeterFlush Bezel

INSTALLATION INSTRUCTIONS

REV 1

WARNING:FAILURE TO COMPLY WITH THE

INSTALLATION INSTRUCTIONS MAYRESULT IN DEATH OR SERIOUS INJURY

WARNING:INSTALL PRODUCT IN ACCORDANCE

WITH LOCAL AND NATIONAL ELECTRICALCODES BY A QUALIFIED ELECTRICIAN

OR ELECTRICAL CONTRACTOR.

CAUTION:INTER-LUX IS NOT RESPONSIBLE FOR THE

STRUCTURAL INTEGRITY OF THE BUILDING TOSUPPORT THE LUMINAIRE. ADDITIONAL BACKING

MAY BE REQUIRED.

*Inter-lux reserves the right to make changes to this product and related installation instructions at any time without prior notice.

ISOMETRIC VIEW

ITEMS NEEDED (SUPPLIED BY OTHERS):PACKAGE INCLUDES: (refer to package list to identify parts)


410-381-1497 inter-lux.com

CAUTION:THIS IS AN ELECTRONIC DEVICE. CARE MUST BE TAKEN

DURING STORAGE AND HANDLING. STORE IN A CLEAN, COOLAND DRY LOCATION. ELECTROSTATIC DISCHARGE (ESD) CAN

HARM THIS PRODUCT. AVOID STATIC DISCHARGE WHILEHANDLING THIS PRODUCT.

MOUNTING DIMENSIONS

WARNING:READ ALL SAFETY INSTRUCTIONS

INCLUDED WITH LUMINAIRE BEFOREINSTALLING LUMINAIRE.

940-20LPF-RBT

3 -

1/8"

M3 Screws

x1

x1

1.75"

slot width

6.0

"

2.0"


Frame

Fram

e

4.9

"

slot width

x Frame

Fram

e

Housing L-Angle Bracket

Illuminated surface

Square Joiner

Flat JoinerSquare Joiner

Housing

Endcap

Set Screw

Housing

Frame

Fram

e

5/8" Drywall Mudded taper

Frame

Fram

e


M4 Fastener

Frame

Fram

eGear Tray

Gear Tray Screw

3 -

7/8"

1 - 3/4"

5/1

6"

C

Mounting Clip

Mounting Clip (C)

3.0

8

1 - 3/4"

5/1

6"

3 -

1/8"

Drill 1/4" Feed Hole 2 -

1/4"


Drill 1/4"Feed Hole

C

A

C

Step 5; Install Housing: Ensure all Low voltage cables are pulled through the wall and accessible. Check that Housings (A) and Luminaires (B) have correct End caps and Joiners installed. Then push the Housing (A) up until it engages with the Mounting Clips (C). Then slide the joiners (example below) halfway in between each Housing (A) and tighten the set screws. Repeat until all Housings (A) are installed. Run Low voltage cable through Housing (A) feed hole. Finally, make electrical connections to Luminaire (B) cables with supplied connectors.

2 - 1/4"

FinishedCeiling

2 - 1/4"

BC

B

A

FinishedCeiling

3 -

1/4"

Luminaire Power Cable

YFill in Joiner Slot

Plaster up to "Knife Edge",no farther

Finished Ceiling

Step 2; Feed Holes: Determine which end the Luminaire (B) cables will start at on each Housing (A) and mark them on the shown location on the Housings (A), no less than 3 inches from the end. Then drill 1/4" holes where you marked. Finally look at where the Housings (A) will be installed and drill 1/4" holes above the line of the Mounting Clips, and close to where the holes in the Housings (A) will end up.

A

A


Snap-inClips

A

Lens

B

Luminarie Power Cable

B

Phillips Head #2 Screwdriver

Wire Connectors

Wire Strippers

M3 Hex head Allen Key

Mounting Screws

LOCATE AND REVIEW ANY CONSTRUCTION PLANS AND INTERLUX RECORD DRAWINGS FOR ALL FIXTURE RUNS. It is recommended to locate and lay out all components for each fixture "run". A fixture run typically consist of joiners, lengths of housings, lengths of inserts, and endcaps.

BE SURE TO IDENTIFY ALL CORRECT LENGTHS FOR EACH FIXTURE RUN.

Step 2: (If single housing skip this step) Insert joiners into next housing as seen below.Place next housing end to end with first housing, slide joiners across housing seam so they are joining both housings. Secure joiners by tightening set screws. Mount housing. Repeat until all housing are installed and mounted.

Joiner Kit

Step 6: Install Gear Trays making electric connections first then insert gear tray into housing (4" Blank Gear Trays go on ends of each run). Refer to pages 2&3 for wiring diagrams if needed. Refer to record drawings for gear tray placement. Secure gear tray to housing using screws in pre-drilled holes. Repeat this step until all gear trays are installed. Energize and test for proper operation.

Housing

Master Gear Tray with DiffuserSatellite Gear Tray with Diffuser

Infill Panel

L-Angle

Endcaps

Blank Gear Tray (4")

x= slot width + 1.75"

Mounting Screws


Flat JoinerHousing

Housing (A)

Luminaire (B)

Wood Backing Drywall AnchorOption A

FinishedCeiling


Step 4: Ensure all Low voltage cables are pulled through the wall and accessible. Then install ceiling, leaving a 1 - 3/4" gap for the Housings (A). Ensure Housings have correct End caps and Joiners installed, then run insert power cable through Housing (A) feed hole and make electrical connection to Low voltage wires with supplied connectors. Finally, push Housing (A) up into the slot until it locks into the Mounting Clips and the flange is flush with the bottom of the ceiling.

Joiners

End Caps

Step 5: Ensure all inserts are Repeat this step until all gear trays are installed. Energize and test for proper operation.

Driver Enclosure

1.5 lb/ft1.5 lb/ft

Step 4; Mounting Hardware: Install Endcaps on first and last Housing (A) of each run. Then install Joiners on each Housing (A), before putting in the ceiling. Install Snap-in Clips on Luminaire (B) using provided screws.

Step 3; Remote Drivers: Install the Remote drivers and run Low voltage cables to the wall. Then run the Low voltage cables through the feed holes drilled above the Mounting Clips (C).

Step 1; Mounting Clips: Turn off Power before Installing. Mark the wall at the intended height of the Mounting Clips (C), 3 - 1/8" above the bottom of the intended ceiling. Then screw Mounting Clips (C) into the wall, it is recommended you use appropriate backing or drywall anchors. The surrounding structure is required to support the weight of the fixture (1 - 1/2 lb per foot). Use at least one Clip every 16", for each Housing (A) Length. For shorter Housings (A), must use at least 2 Clips per Housing (A), 3 recommended. No Clip should be within 3" from the ends of any Housing (A).

Step 6; Install Luminaire: Push the Luminaires (B) up until they snap into the Housings (A). If possible, arrange Luminaire (B) lenses so that they overlap fixture joints. Next, power the Luminaires (B) to double check electrical connections. When the ceiling is installed, it will need to end 2 - 1/4" from the the wall to accomodate the Housings (A).

FinishedCeiling 3

- 1/

8"


PROPRIETARY AND CONFIDENTIAL

PART NO. WG-20LPFW-RBT

Page 2 of 3DRAWING NOT TO SCALE

Whitegoods 20 Linear PerimeterFlush Bezel with Spacer


REV 1


INSTALLATION INSTRUCTIONS MAYRESULT IN DEATH OR SERIOUS INJURY


WITH LOCAL AND NATIONAL ELECTRICALCODES BY A QUALIFIED ELECTRICIAN

OR ELECTRICAL CONTRACTOR.



MAY BE REQUIRED.


ISOMETRIC VIEW

ITEMS NEEDED (SUPPLIED BY OTHERS):PACKAGE INCLUDES: (refer to package list to identify parts)






MOUNTING DIMENSIONS


INCLUDED WITH LUMINAIRE BEFOREINSTALLING LUMINAIRE.

940-20LPFW-RBT

NOTE: ALL SHOWN DRIVERS ARE INTER-LUX PROVIDED. FOR NON INTER-LUX PROVIDED DRIVERS PLEASE REFER TO DRIVERMANUFACTURERS. THE USE OF NON INTER-LUX PROVIDED DRIVERS VOIDS PRODUCT WARRANTY.

3/31/2020

PART NO. WG-20LPF-RBT_20LPF-RBTW


PROPRIETARY AND CONFIDENTIAL Page 3 of 3DRAWING NOT TO SCALE

Driver Wiring Diagrams

SM


INSTALLATION INSTRUCTIONS MAYRESULT IN DEATH OR SERIOUS INJURY.


WITH LOCAL AND NATIONAL ELECTRICALCODES BY A QUALIFIED ELECTRICIAN.



MAY BE REQUIRED.






Maximum Wiring Distance*


INCLUDED WITH LUMINAIRE BEFOREINSTALLING LUMINAIRE. SAVE

INSTRUCTIONS FOR FUTURE USE.

*Actual Voltage drop to be calculated by installer

Wiring Key

Dimming - (Grey)

Switch/Dimmer(if applicable)

AC Power

Ground (Green) Power Supply

Switched Hot (Black)

Neutral (White)

LED lightengine

E1 (Purple)E2 (Purple)

Ground (Green) Power Supply

Line (Black)

Neutral (White)

Dimming + (Purple)

Dimming - (Grey)

LED lightengine

-VDC (Blue/Black) -VDC (Blue/Black)

+VDC (Red) +VDC (Red)

Luminaire

Dimming + (Purple)

Low Voltage - (Blue/Black)

Low Voltage + (Red)Ground (Green)

Line Voltage (Black)

Neutral (White)

LED lightengine

-VDC (Blue/Black)

+VDC (Red) Neutral (White)

Line (Black)

Power Supply

Whitegoods 20 Linear PerimeterFlush Bezel


L3DAE 1%/L3D0E 0.1% Dimming 0-10V Dimming

D3W 1% 3-Wire DimmingStandard Non-Dimming/DFPN Dimming

To E

cosy

stem

Dig

ital L

ink

To L

ine

Vol

tage

To 0

-10V

Dim

Con

trol

To L

ine

Vol

tage

To F

orw

ard

Pha

se C

ontro

l (D

FPN

)

To L

ine

Vol

tage

(Sta

ndar

d)

To F

orw

ard

Pha

se C

ontro

l (D

FPN

)

NeutralLine

Ground

+ Dimming- Dimming

Low Voltage -Low Voltage +

-VDC (Blue/Black)

+VDC (Red) Dimmed Hot (Orange)

LED lightengine

Neutral (White)

Switched Hot (Black)

Power Supply

Ground (Green)

Ground (Green)for DFPN Dimming

Red Blue/Black Green Black White

Positive Negative Ground Line Neutral

Purple Grey

Dimming + Dimming -

Osram

25'

101'

63'

39'

< 48W < 72W < 96W < 40W

25'

15'

40'

60'151'

18'

29'

47'

75'

95'

59'

37'

#12AWG

#14AWG

#16AWG

#18AWG

Wire Gauge LutronMaximum Lead Length

Installation InstructionsDrawing View66Drawing View75Drawing View76Drawing View80Drawing View112Drawing View113Drawing View114Drawing View125Drawing View126Drawing View130Drawing View131Drawing View132Drawing View133Drawing View135Drawing View136Drawing View137Drawing View138Drawing View139Drawing View140Drawing View142Drawing View143Drawing View144Drawing View145Drawing View146Drawing View147Drawing View148Drawing View149Drawing View152Drawing View153Drawing View154Drawing View155Drawing View156Drawing View157Drawing View159Drawing View160Drawing View161Drawing View162Drawing View163Drawing View165Drawing View166Drawing View167Drawing View168Drawing View170Drawing View171Drawing View174Drawing View175Drawing View176Drawing View180Drawing View182Drawing View183Drawing View184Drawing View185Drawing View186Drawing View187Drawing View188Drawing View189Drawing View190Drawing View191Drawing View192Drawing View193Drawing View194Drawing View195Drawing View196Drawing View197Drawing View198Drawing View199Drawing View200Drawing View201Drawing View208Drawing View209Drawing View210Drawing View211Drawing View212Drawing View213Drawing View214Drawing View215Drawing View216Drawing View217Drawing View218Drawing View219Drawing View220Drawing View221Drawing View223Drawing View227Drawing View231Drawing View232Detail View Y (1 : 1.5)Drawing View235Drawing View236Drawing View237Drawing View238Drawing View239Drawing View240Drawing View241Drawing View242Drawing View243Drawing View244Drawing View245Drawing View246Drawing View247Drawing View248Drawing View249Drawing View250Drawing View251Drawing View252Drawing View253Drawing View254Drawing View255Drawing View256Drawing View257Drawing View258Drawing View259Drawing View260Drawing View261Drawing View262Drawing View263Drawing View264Drawing View265Drawing View266Drawing View267Drawing View268Drawing View269Drawing View270Drawing View271Drawing View272Drawing View273Drawing View405Drawing View406Drawing View407Drawing View421Drawing View422Drawing View423Drawing View428Drawing View429Drawing View430

SpacerDrawing View274Drawing View275Drawing View276Drawing View280Drawing View281Drawing View282Drawing View283Drawing View285Drawing View286Drawing View287Drawing View288Drawing View289Drawing View290Drawing View291Drawing View292Drawing View293Drawing View294Drawing View295Drawing View296Drawing View297Drawing View298Drawing View299Drawing View300Drawing View302Drawing View303Drawing View304Drawing View305Drawing View306Drawing View307Drawing View308Drawing View309Drawing View310Drawing View311Drawing View312Drawing View313Drawing View314Drawing View315Drawing View316Drawing View317Drawing View318Drawing View319Drawing View320Drawing View321Drawing View322Drawing View323Drawing View324Drawing View325Drawing View326Drawing View327Drawing View328Drawing View329Drawing View330Drawing View331Drawing View332Drawing View333Drawing View334Drawing View335Drawing View336Drawing View337Drawing View338Drawing View339Drawing View340Drawing View341Drawing View342Drawing View343Drawing View344Drawing View345Drawing View346Drawing View347Drawing View348Drawing View349Drawing View350Drawing View351Drawing View352Drawing View353Drawing View354Drawing View355Drawing View356Drawing View357Drawing View358Drawing View359Drawing View360Drawing View361Drawing View362Drawing View363Drawing View364Detail View Y (1 : 1.5)Drawing View366Drawing View367Drawing View368Drawing View369Drawing View371Drawing View372Drawing View373Drawing View374Drawing View375Drawing View376Drawing View377Drawing View378Drawing View379Drawing View380Drawing View381Drawing View382Drawing View383Drawing View384Drawing View385Drawing View386Drawing View387Drawing View388Drawing View389Drawing View390Drawing View391Drawing View393Drawing View394Drawing View395Drawing View396Drawing View397Drawing View399Drawing View400Drawing View401Drawing View402Drawing View403Drawing View404Drawing View408Drawing View409Drawing View410Drawing View411Drawing View412Drawing View413Drawing View414Drawing View415Drawing View416Drawing View417Drawing View418Drawing View419Drawing View420Drawing View424Drawing View425Drawing View427

Wiring Instructions

whitegoods 20 linear perimeter flush bezel · 2020. 4. 20. · m3 screws x1 x1 1.75" slot width...

Documents