WIRED REMOTE CONTROLLED CAR

PROJECT

ASSEMBLED RC CAR

PROCEDURE TO

ASSEMBLE

RC CAR

Get the required components for the

project:

COMPONENTS QUANTITY

BATTERY 1

DPDT SIWTCH 2

RIBBON WIRE STRIP 3+Metre

DC GEARED MOTOR 4

CHASIS 1

DPDT SWITCH BOX 1

CAR WHEELS 4

SOLDERING SET 1

CONNECTING WIRE IF NEEDED

STEP 1

COMPONENTS OF PROJECT

Solder the ribbon wire strip with the each motors.

Do it for all the four motors.

Place the motors in the chasis.

Tighten the motors with the required spanner.

STEP 2

MOTOR IS PLACED IN THE CHASIS

Now, attach each wheels with the motors.

Tighten the wheels with the motor using the

screw given with the wheels.

Place the wire as given in the diagram.

STEP 3

MOTORS TIGHTEN WITH THE CHASIS

NOW CHECK WHETHER THE ALL THE

SOLDERED WIRES WITH THE MOTORS ARE

WORKING.

ALL THE FOUR MOTORS SHOULD WORK

PROPERLY.

IF NOT CHECK FOR THE CONNECTIONS.

STEP 4

WIRES SOLDERED WITH THE

MOTORS

DECIDE WHICH TWO MOTORS SHOULD GO

FRONT DIRECTION.

AND DECIDE WHICH TWO MOTORS SHOULD

GO IN BACKWARD DIRECTION.

STEP 5

NOW GIVE THE CONNECTIONS FOR THE DPDT SWITCH.

TWO DPDT SWITCHES ARE ENOUGH FOR THE WIRED RC CAR PROJECT.

IN CASE IF YOU WANT THE CAR TO BE SO GRIPPER YOU CAN USE THE FOUR DPDT SWITCHES.

HERE I USED TWO DPDT SWICHES.

STEP 6

CONNECTIONS FOR DPDT

SWITCHES

CONNECTIONS FOR THE TWO DPDT SWITCHES ARE

SHOWN IN THE DIAGRAM

GIVE THE CONNECTIONS AS PER THE CONNECTIONS IN

THE DIAGRAM.

THE CONNECTION IS THAT THE LEFT SIDE TWO MOTORS

ARE FOR ONE SWITCH.

AND THE RIGHT SIDE TWO MOTORS IN THE CAR ARE FOR

ANOTHER SWITCHES.

THIS IS HOW THE CONNECTIONS ARE THERE IN THE

DIAGRAM.

STEP 7

CONNECTIONS FOR EACH

SWITCHES

AND CONNECT THE TWO POSITIVE ENDS OF

THE DPDT SWITCHES.

AND ALSO CONNECT TWO NEGATIVE ENDS

OF THE DPDT SWITCHES.

AND GIVE THESE ENDS TO THE BATTERY.

THE MIDDLE TWO PINS IN BOTH THE DPDT

SWITCH ARE FOR THE BATTERY

CONNECTIONS.

STEP 8

GIVE THE WIRE CONNECTIONS AS SHOWN IN THE

DIAGRAM FOR THE BOX.

PLACE THE WIRES IN THE BOX THROUGH THE

SPECIFIED HOLE.

NOW CONNECT THE WIRES WITH BATTERY.

NOW CHECK THE WIRED REMOTE CONTROLLED

CAR IS WORKING ACCORDING TO THE

FOLLOWING INSTRUCTIONS.

STEP 9

WIRES FROM BOX

CONNECTION OF WIRES WITH THE

BATTERY

ASSEMBLED RC CAR

WORKING OF THE DPDT SWITCHES :

STEP 10

LEFT BUTTON RIGHT BUTTON

UP UP

DOWN DOWN

UP -----------

----------- UP

UP DOWN

DOWN UP

NIL NIL

INSTRUCTIONS OF WORKING OF DPDT SWITCHES:

1.THE RC CAR WILL GO IN THE FRONT DIRECTION.

2.THE RC CAR WILL GO IN THE BACKWARD DIRECTION.

3.THE RC CAR WILL TURN TOWRADS RIGHT.

4.THE RC CAR WILL TURN TOWARDS LEFT.

5.THE RC CAR WILL ROTATE 360 DEGREE TOWARDS RIGHT.

6.THE RC CAR WILL ROTATE 360 DEGREE TOWARDS LEFT.

7.THE RC CAR WILL STOP RUNNING.

STEP 11

IF YOUR WIRED REMOTE CONTROLLED CAR

FOLLOWS THIS INSTRUCTIONS THEN YOU

GOT YOU PERFECT WIRED RC CAR.

STEP 12

CHECK THE CONNECTIONS AND THE

PLACEMENT OF THE MOTORS IN THE

CHASIS AS SHOWN IN THE DIAGRAM.

STEP 13