wireless access control system › wp-content › uploads › amii.pdfintroduction the am/ii is...
TRANSCRIPT
-
Wireless Access Control System
Installation & Programming Instructions
(760) 438-7000 • FAX (760) 438-7043USA & Canada (800) 421-1587 & (800) 392-0123
Toll Free FAX (800) 468-1340www.linearcorp.com
RADIO
RADIO
DECODE
ACCESS GRANTED
PERIPHERALS
READER KEYPAD
ACCESS OUT DATA
NETWORK DATA
ACCESS A
ACCESS B
ACCESS C
OBSTACLE
MAGIC WAND
ACCESS D
SYSTEM
POWER
RESET
DISPLAYCONTRAST
BO 1 O 1 O 1 BO 1 N.O. COM. N.C. N.O. COM. N.C. N.O. COM. N.C. N.O. COM. N.C.
EARTHGROUND
ACCESS OUT KEYPAD IN CHANNEL A CHANNEL B CHANNEL C CHANNEL DREADER IN14 - 24 VAC12 - 35 VDC
AC POWERINPUT
DC POWERINPUTNETWORK
OFF
ON
POWER
RS-232
MEMORY EXPANSION CARD
MEDIUM (64 K)
SMALL (16 K) LARGE (128 K)
X-LARGE (256 K)
WARNING
TURN THE POWER SWITCH OFF BEFORE INSTALLING ORREMOVING THIS MEMORY EXPANSION CARD
SEVEREELECTRICAL
DAMAGE
RELAYS
EXTERNAL CONTROL
For AM/IIVersion 5.0
*
5 6
7 8 9
0 #
1 2 3
4
-
TABLE OF CONTENTSFEATURES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Remote Access Software . . . . . . . . . . . . . . . . . . . . . . . . . . 3AM/II ACCESSORIES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4AM/II FEATURES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5SYSTEM HARDWARE BLOCK DIAGRAM . . . . . . . . . . . . . . . . . . . . 6
BUTTON SCHEDULE . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8DOOR SCHEDULES . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9TIME ZONES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10ANTI-PASSBACK & KEYPAD STRIKEOUT . . . . . . . . . . . . . . . 11VALIDATION GROUPS . . . . . . . . . . . . . . . . . . . . . . . . . . 12EVENT LOG . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13REMOTE DEVICES . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14ACCESS MEDIA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15RELAY OUTPUTS & SENSING INPUTS . . . . . . . . . . . . . . . . . 16RS-232 PORT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17ACCESS OUT & NETWORK TERMINALS . . . . . . . . . . . . . . . . 18MEMORY UTILITIES . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
PRE-INSTALLATION PLANNING . . . . . . . . . . . . . . . . . . . . . . . . 20INSTALLATION OUTLINE . . . . . . . . . . . . . . . . . . . . . . . . . . . 20WIRELESS INSTALLATION TIPS . . . . . . . . . . . . . . . . . . . . . . . 21
Signals Through Construction Materials . . . . . . . . . . . . . . . . . . 21Transmitters in Vehicles . . . . . . . . . . . . . . . . . . . . . . . . . . 21
PRE-INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21Unpacking the System . . . . . . . . . . . . . . . . . . . . . . . . . . . 21Installing the Memory Module . . . . . . . . . . . . . . . . . . . . . . . 21
MOUNT UNIT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22EARTH GROUND & POWER CONNECTIONS . . . . . . . . . . . . . . . . . 23
Earth Ground . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
REMOTE DEVICE WIRING REQUIREMENTS . . . . . . . . . . . . . . . . . 24Cable Type . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24Load Number . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
ANTENNA HOOK-UP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25REMOTE RADIO RECEIVER CONNECTIONS . . . . . . . . . . . . . . . . . 25REMOTE KEYPAD CONNECTIONS . . . . . . . . . . . . . . . . . . . . . . 26REMOTE PROXIMITY RECEIVER . . . . . . . . . . . . . . . . . . . . . . . 26CARD READER INTERFACE . . . . . . . . . . . . . . . . . . . . . . . . . . 27CONTROL INPUTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Open Request . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27Door Sense . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
RELAY OUTPUT CONNECTIONS . . . . . . . . . . . . . . . . . . . . . . . 28Relay Operation Options . . . . . . . . . . . . . . . . . . . . . . . . . . 28
RS-232 PORT CONNECTIONS . . . . . . . . . . . . . . . . . . . . . . . . . 30Printer Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30Personal Computer and Data Terminal Connections . . . . . . . . . . . 31Modem Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
ACCESS OUT CONNECTIONS . . . . . . . . . . . . . . . . . . . . . . . . . 32NETWORK CONNECTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . 33
SYSTEM POWER-UP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34First Time Power-up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34Internal Diagnostic Checks . . . . . . . . . . . . . . . . . . . . . . . . . 34Watchdog Monitor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
MEDIA ENCODING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34Transmitter Coding . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34Block Coded Transmitters . . . . . . . . . . . . . . . . . . . . . . . . . . 34Block Coded Cards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34Keypad Entry Codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
DISPLAYS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35Radio Indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35Decode Indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35Access Granted Indicator . . . . . . . . . . . . . . . . . . . . . . . . . . 35
KEYPAD FUNCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36Data Entry Keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36Numeric Keypad . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36[*] Key . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36[#] Key . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36Alphanumeric Data Entry . . . . . . . . . . . . . . . . . . . . . . . . . . 36
SYSTEM PROGRAMMING . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37Entering Program Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . 37Exiting Program Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
PROGRAMMING MENU TREES . . . . . . . . . . . . . . . . . . . . . . . . . 38PROGRAMMING OUTLINE . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40AREA 01SINGLE TRANSMITTER PROGRAMMING . . . . . . . . . . . . . . . . . . . 41
Learning Single Transmitters . . . . . . . . . . . . . . . . . . . . . . . . 41Suspending Single Transmitters . . . . . . . . . . . . . . . . . . . . . . 41Reactivating Single Transmitters . . . . . . . . . . . . . . . . . . . . . . 41Status of Single Transmitters . . . . . . . . . . . . . . . . . . . . . . . . 41Deleting One Single Transmitter . . . . . . . . . . . . . . . . . . . . . . 41Deleting All Single Transmitters . . . . . . . . . . . . . . . . . . . . . . . 41
AREA 02BLOCK TRANSMITTERS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
Entering Block Transmitters . . . . . . . . . . . . . . . . . . . . . . . . . 42Suspending Block Transmitters . . . . . . . . . . . . . . . . . . . . . . . 42Reactivating Block Transmitters . . . . . . . . . . . . . . . . . . . . . . . 42Status of Block Transmitters . . . . . . . . . . . . . . . . . . . . . . . . 42Deleting All Block Transmitters . . . . . . . . . . . . . . . . . . . . . . . 42
AREA 03OBSTACLE TRANSMITTERS . . . . . . . . . . . . . . . . . . . . . . . . . . 43
Naming Obstacle Transmitters . . . . . . . . . . . . . . . . . . . . . . . 43Learning Obstacle Transmitters . . . . . . . . . . . . . . . . . . . . . . . 43Deleting Obstacle Transmitters . . . . . . . . . . . . . . . . . . . . . . . 43
AREA 04MAGIC WAND TRANSMITTERS . . . . . . . . . . . . . . . . . . . . . . . . . 44
Naming Magic Wand Transmitters . . . . . . . . . . . . . . . . . . . . . 44Learning Magic Wand Transmitters . . . . . . . . . . . . . . . . . . . . . 44Deleting Magic Wand Transmitters . . . . . . . . . . . . . . . . . . . . . 44
-
AREA 05ENTRY CODES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
Entering Entry Codes . . . . . . . . . . . . . . . . . . . . . . . . . . . 45Suspending Entry Codes . . . . . . . . . . . . . . . . . . . . . . . . . 45Reactivating Entry Codes . . . . . . . . . . . . . . . . . . . . . . . . . 45Status of Entry Codes . . . . . . . . . . . . . . . . . . . . . . . . . . . 45Deleting One Single Entry Code . . . . . . . . . . . . . . . . . . . . . . 45Deleting All Entry Codes . . . . . . . . . . . . . . . . . . . . . . . . . . 45
AREA 06BLOCK CARD CODES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
Entering Block Card Codes . . . . . . . . . . . . . . . . . . . . . . . . 46Suspending Block Card Codes . . . . . . . . . . . . . . . . . . . . . . 46Reactivating Block Card Codes . . . . . . . . . . . . . . . . . . . . . . 46Status of Block Card Codes . . . . . . . . . . . . . . . . . . . . . . . . 46Deleting All Block Card Codes . . . . . . . . . . . . . . . . . . . . . . . 46
AREA 07TELEPHONE ENTRY NUMBERS . . . . . . . . . . . . . . . . . . . . . . . . 47
Entering Tenant Names & Numbers . . . . . . . . . . . . . . . . . . . . 47Deleting Directory Entries . . . . . . . . . . . . . . . . . . . . . . . . . 47
AREA 10VALIDATION GROUPS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
Configuring Validation Groups . . . . . . . . . . . . . . . . . . . . . . . 48AREA 11BUTTON SCHEDULES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
Setting the Channel “A” Button Schedule . . . . . . . . . . . . . . . . . 49Setting the Channel “B” Button Schedule . . . . . . . . . . . . . . . . . 49Setting the Channel “C” Button Schedule . . . . . . . . . . . . . . . . . 49Setting the Channel “D” Button Schedule . . . . . . . . . . . . . . . . . 49
AREA 12DOOR SCHEDULES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
Setting the Door Schedules . . . . . . . . . . . . . . . . . . . . . . . . 50AREA 13TIME ZONES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
Setting the Time Zones . . . . . . . . . . . . . . . . . . . . . . . . . . 51AREA 20TIME AND CALENDAR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
Setting the Time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52Setting the Date . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52Daylight Savings Option . . . . . . . . . . . . . . . . . . . . . . . . . . 52Setting Keypad Downlight Time . . . . . . . . . . . . . . . . . . . . . . 52Setting Holiday Dates . . . . . . . . . . . . . . . . . . . . . . . . . . . 52Setting Expiring Holiday Dates . . . . . . . . . . . . . . . . . . . . . . 52
AREA 21RELAY SETUP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
Relay Timing Options . . . . . . . . . . . . . . . . . . . . . . . . . . . 53Relay Programming . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
AREA 22SYSTEM SETUP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
Setting Installation and Unit Names . . . . . . . . . . . . . . . . . . . . 54Setting Event Log Limits . . . . . . . . . . . . . . . . . . . . . . . . . . 54Setting Anti-Passback Time . . . . . . . . . . . . . . . . . . . . . . . . 54Setting Intregral Radio Direction . . . . . . . . . . . . . . . . . . . . . . 54Setting Network Address . . . . . . . . . . . . . . . . . . . . . . . . . 54Setting Keypad Strike Outs . . . . . . . . . . . . . . . . . . . . . . . . 54Setting Door Ajar Time . . . . . . . . . . . . . . . . . . . . . . . . . . . 54Setting Local Password . . . . . . . . . . . . . . . . . . . . . . . . . . 54Setting Remote Password . . . . . . . . . . . . . . . . . . . . . . . . . 54Setting Priority Access Password . . . . . . . . . . . . . . . . . . . . . 54
AREA 23Facility/Site Codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
System Site Code . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55Transmitter Facility Code . . . . . . . . . . . . . . . . . . . . . . . . . 55Card Facility Codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
AREA 24RS-232 PORT SETUP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56
Setting RS-232 Device . . . . . . . . . . . . . . . . . . . . . . . . . . 56Changing Modem Initialization Strings . . . . . . . . . . . . . . . . . . . 56Setting Modem Termination String . . . . . . . . . . . . . . . . . . . . 56
AREA 25CONFIGURE REMOTE DEVICES . . . . . . . . . . . . . . . . . . . . . . . 57
Remote Device Programming . . . . . . . . . . . . . . . . . . . . . . . 57AREA 26CONFIGURE ACCESS OUT . . . . . . . . . . . . . . . . . . . . . . . . . . 58
Access Out Application Note . . . . . . . . . . . . . . . . . . . . . . . 58Access Out Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58
AREA 27TELEPHONE ENTRY SETUP . . . . . . . . . . . . . . . . . . . . . . . . . . 59
Configuring Directory . . . . . . . . . . . . . . . . . . . . . . . . . . . 59Setting PBX Dialing Digit . . . . . . . . . . . . . . . . . . . . . . . . . 59Setting Talk Time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59Editing Display Messages . . . . . . . . . . . . . . . . . . . . . . . . . 59Deleting All Telephone Entries . . . . . . . . . . . . . . . . . . . . . . 59Adjusting the Speaker/Microphone Balance . . . . . . . . . . . . . . . . 59Set Priority Access Function . . . . . . . . . . . . . . . . . . . . . . . . 59
AREA 29MEMORY MODULE UTILITIES . . . . . . . . . . . . . . . . . . . . . . . . . 60
Sending Memory Module . . . . . . . . . . . . . . . . . . . . . . . . . 60Receiving Memory Module . . . . . . . . . . . . . . . . . . . . . . . . 60Copying Memory Module . . . . . . . . . . . . . . . . . . . . . . . . . 60Printing Memory Module . . . . . . . . . . . . . . . . . . . . . . . . . . 60Initializing Memory Module . . . . . . . . . . . . . . . . . . . . . . . . 60
AREA 30SYSTEM REPORTS/UTILITIES . . . . . . . . . . . . . . . . . . . . . . . . . 61
Printing System Report . . . . . . . . . . . . . . . . . . . . . . . . . . 61Printing Single Transmitter Report . . . . . . . . . . . . . . . . . . . . . 61Printing Block Transmitter Report . . . . . . . . . . . . . . . . . . . . . 61Printing Entry Code Report . . . . . . . . . . . . . . . . . . . . . . . . 61Printing Block Card Report . . . . . . . . . . . . . . . . . . . . . . . . 61Printing Telephone Entry Report . . . . . . . . . . . . . . . . . . . . . 61Printing Event Log . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61
OPERATION OVERVIEW . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62Standard Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62Manual Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62Magic Wand Transmitters . . . . . . . . . . . . . . . . . . . . . . . . . 62Obstacle Transmitters . . . . . . . . . . . . . . . . . . . . . . . . . . . 62
SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63Outputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63Inputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63Hardware . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63Construction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63
INDEX . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64LINEAR LIMITED WARRANTY . . . . . . . . . . . . . . . . . . . . . . . . . 66
1
-
INTRODUCTIONThe AM/II is designed for a broad range of access controlapplications. Its wireless design with the proven MegaCoderadio format, the Wiegand and RS-232 interfaces, make iteasily adaptable for virtually any access control requirement.The AM/II contains a high-gain superheterodyne UHF receiver.When used with an external antenna, signals can be receivedfrom up to 200 feet away. Two lockable metal enclosures areavailable to house the AM/II.Four dry contact relay outputs are provided to activate fouraccess devices, such as door strikes, barrier gates, automaticsliding gates and automatic doors. The relay outputs can alsobe used for alarm contact shunting, operator obstacletriggering, and alarm activation. Two open request pushbuttoninputs are supplied for hardwire activation of the accessdevices. Two door sense inputs allow detection of proppedopen doors.The AM/II has an RS-232 interface (bi-directional). The systemcan be linked to a printer or personal computer. The event logfeature, for example, makes it possible to keep track of howmany employees are on premises, which employees arepresent, and when they clock in and out. With connection to apersonal computer, the AM/II can be programmed locally orremotely through the telephone system with standard Hayescompatible modems. System reports can be printed orcaptured from the RS-232 port.
The Wiegand interface is for connect ion to othermanufacturer’s access control systems. The AM/II can act asa wireless receiver for an existing access control system. Wheninterconnected to a Sentex Infinity system, the AM/II cansimulate two Sentex card readers, receiving signals fromthousands of transmitters. The AM/II also supports the industrystandard Wiegand26 and Securakey31 data formats forconnecting to other access control panels.Up to eight AM/II’s can be networked together allowinginformation sharing between the units. A common event log isretained for all of the networked units.Four different size memory modules are available. The small,medium, large and x-large modules allow tailoring the systemto meet the requirements of the installation. The larger thememory module, the more transmitter ID codes and loggedevents can be stored.Additional remote accessory devices can be connected to theAM/II. A rugged, die cast, weatherproof keypad (AM-KP) formanual input of entry codes. A card reader interface (AM-CRI)can connect to one or two card readers. A proximity receiver(AM-RPR) provides ultra-short range radio reception fortransmitters. A remote radio receiver (AM-RRR) can be usedto extend the reception capabilities of the AM/II. Up to sixremote accessory devices can be used with each AM/II unit.
OKBACK NEXT
AM/II
Barrier Gate with ControlledDoor, Remote Receivers andRemote Keypads.Access is Controled with Time Zones.
Safety EdgeTransmitter
Modem for RemoteAccess & Programming
Barrier Gate
Controlled Door
Keypad &RemoteReceiver
User Tx
User Tx
ProximityReceiver
STANDARD 2-WIRE DOORSTRIKECONNECTION
6-WIRELOCAL BUS
Keypad
DoorStrike
6-WIRELOCAL BUS
STANDARD 2-WIRE SIGNALCONNECTION
2
-
FEATURES✶ Ideally suited for gated communities, condos, airports,
parking garages, municipal gated parking, office buildings,government buildings, hospitals, factories, utilitycompanies, computer facilities, museums, warehouses,dormitories, banks, libraries, retail stores, hotels/motels,educational facilities, small commercial buildings andrecreational facilities.
✶ Controls up to four access devices.✶ Supports thousands of transmitters, entry codes and card
codes (depends on memory module size).✶ MegaCode radio format features over one million possible
transmitter identification codes.✶ Remote activation from up to 200 feet away.✶ Integral 2 line by 24 character backlit LCD display.✶ Real-time print log (RS-232 output to a line printer).✶ Remote and local programming with a personal computer.✶ Sentex30, Securakey31, and Wiegand26 compatible output
to connect to other access control panels.✶ Block coding for transmitters and cards (just the first and last
number in a “block” needs to be programmed).✶ Magic wand support (special transmitter for maintenance
personnel).✶ Obstacle-sensing support with Linear’s MGT Safety Edge
transmitter.✶ Two door sensing inputs for propped open doors.
✶ Automatic door relock when door sense input is used.✶ Two request to exit inputs for pushbutton or knox box
activation.✶ Time scheduled relay activation, 15 time zones with 4
periods each.✶ Time zone access validation, 15 time zones with 4 periods
each.✶ Day of week and holiday access validation, up to 24 expiring
holidays and 24 non-expiring holidays.✶ Door access restriction for each validation group.✶ Timed anti-passback modes.
Remote Access SoftwareEither of the following two Windows based softwareprograms can be downloaded f rom our website(www.linearcorp.com)✶ Access Base - used in networks or single AM/II installations.✶ Account Manager - used in non-networked, single AM/II
installations.
0 7 : 0 0 A C C E S S U S E R 20 7 : 1 0 A C C E S S U S E R 1 70 7 : 1 4 A C C E S S U S E R 3 40 7 : 1 5 A C C E S S U S E R 4 50 7 : 1 9 A C C E S S U S E R 2 70 7 : 2 3 A C C E S S U S E R 5 60 7 : 2 4 A C C E S S U S E R 1 20 7 : 2 6 A C C E S S U S E R 1 30 7 : 2 6 A C C E S S U S E R 2 30 7 : 2 7 A C C E S S U S E R 8 70 7 : 2 8 A C C E S S U S E R 6 70 7 : 2 9 A C C E S S U S E R 9 8
L O B B Y
ACCOUNTING
S E R V I C E
S A L E S
P R E S I D E N T
V . P .V . P .
S A L E S P U R C H .
E N G I N E E R I N G
B A T H B A T H
COMPUTER
ROOM
S T O R .
C O P I E RA R E A
C H I E FE N G .
L A B
AM/II(Two Networked Units)
Small Commercial Installationwith Two Time Zones. FourDoors: Customer Entrance,Employee Entrance, ComputerRoom & President's Back Door
Printer forEvent Logging
Keypad
CardReader
EMPLOYEEENTRANCE
CUSTOMERENTRANCE
CRTEventLogging
RECEPTIONIST
DoorRelease
CardReader
COMPUTER ROOMSPECIAL ACCESS
Modem forRemoteProgramming
OKBACK NEXT
CardReader
PRESIDENT'S OFFICESPECIAL ACCESS
3
-
AM/II ACCESSORIES
*
5 6
7 8 9
0 #
1 2 3
4
M D T K
2 - B u t t o n M e g a C o d e T r a n s m i t t e r
T o p a n d f r o n t b u t t o n sf u n c t i o n t h e s a m e t oc o n t r o l a s i n g l er e l a y c h a n n e l .
3 - B u t t o n M e g a C o d e T r a n s m i t t e r
T w o f r o n t b u t t o n s a n d at o p b u t t o n c a n b e u s e dw i t h a n y r e l a y c h a n n e l .
2 - B u t t o n M e g a C o d eM i n i T r a n s m i t t e r
D e s i g n e d t o b e u s e d w i t ht h e k e y c h a i n p r o v i d e d . A c t i v a t e s t w o r e l a y c h a n n e l s .
1 - B u t t o n M e g a C o d eM i n i T r a n s m i t t e r
D e s i g n e d t o b e u s e d w i t ht h e k e y c h a i n p r o v i d e d . A c t i v a t e s o n e r e l a y c h a n n e l .
M e g a C o d e W i r e l e s s K e y p a d
U s e r c o d e i s e n t e r e d o n k e y p a d .K e y p a d h a s w e a t h e r - p r o o fc o n s t r u c t i o n , e a s y t o r e a d n u m b e r s a n d i s b a c k l i t f o ru s e a t n i g h t . C a n b e u s e d f o r u pt o 1 5 2 4 s i n g l e t r a n s m i t t t e r c o d e s .
M D T - 2
SINGLE & BLOCK CODEDTRANSMITTERS
REMOTE ACCESSORY DEVICES
5 - B u t t o n M e g a C o d e T r a n s m i t t e r
C a n c o n t r o l a l l r e l a yc h a n n e l s o r b e u s e d a sa m a g i c w a n d t r a n s m i t t e r .
M D T - 4M D T - 1
A C T - 2 2A C T - 2 1
M G TA M - K P
A M - R R R
A M - C R I A M - R P R
S u p e r v i s e d G a t e S a f e t yE d g e T r a n s m i t t e r
C o n n e c t s t o s a f e t y e d g es e n s o r . A c t i v a t e s o b s t a c l er e l a y c h a n n e l .
E n t r y K e y p a d
O u t d o o r h o u s i n g w i t hl i g h t e d k e y p a d a n d t w oi n d i c a t o r s . A c t i v a t e s o n er e l a y c h a n n e l .
E X A - 1 0 0 0
E X A - 2 0 0 0
R e m o t e A n t e n n a s
D i r e c t i o n a l a n d o m n i -d i r e c t i o n a l a n t e n n a s f o rr e m o t e p l a c e m e n t i n b e s tr e c e p t i o n a r e a s .
R e m o t e R a d i o R e c e i v e r
H i g h - g a i n r e m o t e r a d i or e c e i v e r w i t h o u t d o o rh o u s i n g .
C a r d R e a d e rI n t e r f a c e
C o n n e c t s t o o n e o rt w o 2 6 - b i t o r 3 1 - b i t c a r dr e a d e r s . F u n c t i o n s a st w o r e m o t e d e v i c e s .
R e m o t e P r o x i m i t yR e c e i v e r
R e c e i v e s t r a n s m i t t e rs i g n a l s f r o m i n c h e sa w a y . F o r t r a n s m i t t e ra c t i v a t i o n o f s p e c i f i ca c c e s s p o i n t .
4
-
AM/II FEATURES
1. MEMORY EXPANSION CARDPlug-in memory module. Four sizes available: small, medium, large andjumbo.
2. RESET BUTTONResets and restarts the microprocessor. Runs startup tests.
3. POWER LIGHTIndicates that DC or AC power is being applied to the unit and that thePOWER switch is turned on.
4. DISPLAY CONTRAST CONTROLAdjusts the contrast of the unit’s LCD display. Allows setting the displayfor maximum readability for different viewing angles.
5. LCD DISPLAYBacklit, 24-character-per-line, 2-line LCD display. Displays systemoperation and programming information.
6. RADIO RANGE KNOBControls the gain of the radio receiver. Used to limit the maximumoperating range of transmitters. Turn clockwise for more gain,counterclockwise for less gain.
7. ANTENNA INPUTFor connection to the EXA-1000 omni-directional or EXA-2000 directionalremote antenna.
8. DATA ENTRY KEYSArrow keys are used to scroll through displayed menu trees. OK key isused as an enter key to accept data entered or selected.
9. RADIO INDICATORThe RADIO light indicates the presence of RF signal into the unit’sreceiver.
10. NUMERIC KEYPADUsed for entering data while programming the AM/II.
11. RS-232 PORTConnects to a serial line printer, PC or data terminal for logging accesstransactions. For local programming with a PC or remote programmingwith a PC and a modem. Also used to interconnect two AM/II units to copythe memory between systems.
12. POWER SWITCHControls the DC and AC power inputs. This is the master power switchfor the AM/II.
13. EARTH GROUND TERMINALFor connection to a good earth ground. For electrical safety and optimumlightning protection, this connection is mandatory.
14. POWER TERMINALSDC power input terminals for 12 to 35 VDC. AC power input terminals for14 to 24 VAC. Use either AC or DC power, DO NOT USE BOTH.
15. RELAY INDICATORS AND ACCESS BUTTONSIndicators will light when an output relay is activated. Outputs can beactivated (open) by a transmitter or locked open by pressing an ACCESSbutton.
16. EXTERNAL CONTROL INDICATORSMAGIC WAND indicator lights when the special “MAGIC WAND”transmitter is activated by a system administrator. OBSTACLE indicatorlights when a signal from a Model MGT safety edge transmitter isreceived.
17. RELAY TERMINALSConnects to the access device to be controlled (door strike, gate operator,etc.). Open request switch inputs are provided for relay channels A & B.
18. WIRING STRAIN RELIEF HOOKSStrain relief hooks are provided on the bottom of the AM/II case. Afterwiring is complete, wires can be zip-tied to the strain relief hooks.
19. PERIPHERALS INDICATORSThe DECODE light indicates that the data being received is a valid formatthat the unit recognizes. The ACCESS GRANTED indicator lights whena device that is allowed to have access is triggered. The ACCESS IN andACCESS OUT indicators light when data is being sent or received fromthe remote devices.
20. READER IN TERMINALSConnects to remote accessory devices.
21. KEYPAD IN TERMINALSConnects to remote accessory devices.
22. ACCESS OUT TERMINALSAccessNet Data Bus for connection to other access control units. Sentexaccess out format is programmable for connection to Sentex Infinitysystems. Wiegand26 and SecuraKey31 access out formats areprogrammable for connection to Wiegand inputs on other access controlunits.
23. NETWORK TERMINALSFor connection to other AM/II units. Up to 8 units can be networkedtogether.
EXPANSION MEMORY CARD RADIO
RADIO
DECODE
ACCESS GRANTED
PERIPHERALS
READER KEYPAD
ACCESS OUT DATA
ACCESS IN DATA
RELAYS
ACCESS A
ACCESS B
ACCESS C
EXTERNAL CONTROL
OBSTACLE
MAGIC WAND
ACCESS D
SYSTEM
POWER
RESET
DISPLAYCONTRAST
BO 1 O 1 O 1 BO 1 N.O. COM. N.C. N.O. COM. N.C. N.O. COM. N.C. N.O. COM. N.C.
EARTHGROUND
ACCESS OUT KEYPAD IN CHANNEL A CHANNEL B CHANNEL C CHANNEL DREADER IN14 - 24 VAC12 - 35 VDC
AC POWERINPUT
DC POWERINPUTNETWORK
O K
OFF
ON
POWER
RS-232
MEMORY EXPANSION CARD
MEDIUM (64 K)
SMALL (16 K) LARGE (128 K)
X-LARGE (256 K)
WARNING
TURN THE POWER SWITCH OFF BEFORE INSTALLING ORREMOVING THIS MEMORY EXPANSION CARD
SEVEREELECTRICAL
DAMAGE
1 41 51 61 71 81 92 02 1
1
2
3 45 6 7
8 9
1 01 1
1 2
2 2
1 3
2 3
5
-
SYSTEM HARDWARE BLOCK DIAGRAM
RADIO
MICROPROCESSOR
INDICATORS DISPLAY KEYBOARD
MEMORYMODULE
RS-232PORT
NETWORKTERMINALS
ACCESS OUTTERMINALS
KEYPADTERMINALS
READERTERMINALS
DOOR SENSE & OPEN REQ.
RELAYTERMINALS
USER'STRANSMITTERS
OBSTACLETRANSMITTERS
ANOTHERAM/II
ANOTHERAM/II
UP TO 8NETWORK
UNITS
EXTERNALACCESS
CONTROLPANEL
AM-KPKEYPAD
[DV4]
AM-KPKEYPAD
[DV5]
AM-KPKEYPAD
[DV6]
AM-RPRRECEIVER
[DV1]
AM-RRRRECEIVER
[DV2]
AM-CRIREADER
[DV3]
MAGNETICSWITCHES
& PUSHBUTTONS
ACCESS DEVICES(DOOR STRIKES,
OPERATORS)7
1
2 3
86
5
4
AM/II CONTROL
6
-
➀AM/II CONTROL
The AM/II is a microprocessor based, world class accesscontrol system with a built-in superheterodyne radio receiver.The microprocessor runs the entire system, granting access,performing system “housekeeping” functions, displayinginformation, reading inputs and controlling outputs.Programming information and event logs are stored in theremovable memory module. The soft touch silicone keypad andnumeric keys are used for data entry. The plug-in terminalblocks connect to access devices, power, remote devices andsensing inputs. The RS-232 port connects to external computerequipment for event logging and system programming.
➁RADIO TRANSMITTERS
Many models of transmitters can be used with the AM/II. Someare individually coded, others are coded in blocks of numbers.Both code types will appear to function the same to the endusers. The users will activate their transmitter to attempt to gainaccess. When the transmitted signal is detected by an AM/IIreceiver, the control decides if the user is currently allowedaccess. If the programming in the AM/II determines that theuser can have access at that time, the programmed outputrelay will activate. Model MGT gate obstacle transmitters canalso send signals to the AM/II.
➂EXTERNAL ANTENNA
The AM/II control has a type “F” antenna connector. Theexternal antenna is connected with co-ax cable to theconnector. A Model EXA-1000 (omni-directional), or ModelEXA-2000 (directional) antenna is used to receive signals fromthe user’s transmitters. The radio gain control knob can be usedto custom tailor the reception area to the installation.
➃ACCESS DEVICES
The access devices wired to the relay terminals control specificaccess portals. When a user is granted access by the AM/II theaccess device activates (usually for a timed period).
➄OPEN REQUEST AND DOOR SENSE
INPUTSThe open request inputs wire to pushbuttons or knox boxes sothat users can activate access devices without needing theircard code or transmitter. Open request pushbuttons are usuallynext to the controlled portal inside the controlled area. Doorsense inputs are wired to normally closed magnetic ormechanical switches attached to the door.
➅REMOTE DEVICES
The remote devices communicate with the AM/II through acommon electrical buss. Each device is set to a unique deviceaddress so the AM/II can recognize each unit as an individual.Currently available remote devices include entry keypads,remote radio receivers, radio proximity receivers and cardreader interfaces.
➆EXTERNAL ACCESS CONTROL
Access control panels from other manufacturers can beconnected to the AM/II. The AM/II can serve as a remote devicefor the external panel. The external panel can validate the datacoming from the AM/II and perform its own access functions.
➇NETWORKED UNITS
Up to eight AM/II’s can be networked together to function inunison. Each AM/II functions as an independent unit, butprogramming and event logging is shared between all units.Cards, codes and transmitters can be programmed to activatea specific AM/II unit.
7
-
BUTTON SCHEDULE
Select which transmitter buttonsactivate which relay channels
CONCEPTSThe following pages provide a foundation forlearning the access control concepts used in
the AM/II system.
BUTTON DEFAULTSCHANNEL "A" = LEFTCHANNEL "B" = RIGHTCHANNEL "C" = BOTTOM-LEFTCHANNEL "D" = BOTTOM-RIGHT
BOTHFUNCTIONAS LEFTBUTTON
LEFTBUTTON
RIGHTBUTTON
TOPBUTTON
TOPBUTTON
LEFTBUTTON
RIGHTBUTTON
BOTTOM-RIGHTBUTTONBOTTOM-LEFT
BUTTON
LEFTBUTTON
LEFTBUTTON
RIGHTBUTTON
ANY TRANSMITTERBUTTON CAN BE
PROGRAMMED TOACTIVATE ANY
RELAY CHANNEL
SPECIAL INFORMATIONThe button schedule must be set before programming any validation group.
Each validation group can have different button schedules.
To avoid confusion, using the same button schedule for all validation groups is recommended.
A
B
C
D
RELAYCHANNEL "A"
RELAYCHANNEL "B"
RELAYCHANNEL "C"
RELAYCHANNEL "D"
BOTH EQUALSTOP BUTTON
?
??
?
BUTTONSCHEDULE
8
-
DOOR SCHEDULES
Select which relay channels a validationgroup can access
CONCEPTS
SPECIAL INFORMATION
Program door schedules before programming validation groups.
Door schedule 0 [DS0] always allows access to all four door relay channels.
Up to 15 door schedules can be programmed.
UP TO 15 DIFFERENT DOOR SCHEDULES [DS1 - DS15] CAN BE SET
RELAYCHANNEL "A"
RELAYCHANNEL "B"
RELAYCHANNEL "C"
RELAYCHANNEL "D"
EACH DOOR SCHEDULE SETS WHICH RELAY CHANNEL(S) THAT THE SCHEDULE CAN ACTIVATE
DOOR SCHEDULE
A B C DDOOR SCHEDULE
9
-
TIME ZONES
Select the days of the week & whattimes that a validation group
will be active
CONCEPTSTIMEZONE
SPECIAL INFORMATIONTime zones also enables holiday schedules for a validation group.
Up to 15 time zones can be programmed.
Note: 00:00 settings for all time periods in a time zone allows 24-hour access.
Time zone 0 [TZ0] always allows 24-hour access.
VALID DAYS SET WHICH DAY(S) THE TIME ZONE IS ACTIVE. HOLIDAY OPTION ALLOWS ACCESS ON PROGRAMMED HOLIDAY DAYS.
UP TO 15 DIFFERENT TIME ZONES [TZ1 - TZ15] CAN BE SET
UP TO FOUR SEPARATE TIME PERIODS CAN BE SET FOR EACH TIME ZONE. ACCESS WILL ONLY BE GRANTED DURING A TIME PERIOD.
VALID DAYS❍ SUN❍ MON❍ TUES❍ WED
❍ THURS❍ FRI❍ SAT❍ HOLIDY
TIME PERIOD 1
BEGIN TIME: 00:00
END TIME: 00:00
TIME PERIOD 2
BEGIN TIME: 00:00
END TIME: 00:00
TIME PERIOD 3
BEGIN TIME: 00:00
END TIME: 00:00
TIME PERIOD 4
BEGIN TIME: 00:00
END TIME: 00:00
TIME
ZONE
10
-
ANTI-PASSBACK & KEYPAD STRIKEOUT
Timed anti-passback prevents“tailgating” by unauthorized users,
keypad strikeout discourageskeycode “guessing”
CONCEPTS
ANTI-PASSBACK
& STRIKEOUT
SPECIAL INFORMATIONAnti-passback time can be programmed to 1, 2, 3 or 4 minutes.
Intregral radio direction must be set to IN for anti-passback to function.
Keypad strikeout can be set from one to seven failed attempts.
*
5 6
7 8 9
0 #
1 2 3
4
*
5 6
7 8 9
0 #
1 2 3
4
YELLOW LIGHT SHOWSLOCKED OUT CONDITION
WHEN ANTI-PASSBACKOPTION IS ENABLED ANDTRANSMITTER IS ACTIVATED...
THE TRANSMITTER WILL NOT HAVEACCESS AGAIN UNTIL ANTI-PASSBACKTIME EXPIRES
WHEN KEYPAD STRIKEOUTS ARE SET, AFTER THE SET NUMBER OF WRONG CODE ATTEMPTS THE KEYPAD WILL "LOCKOUT" IGNORING FURTHER ATTEMPTS UNTIL ONE MINUTE PASSES
11
-
VALIDATION GROUPS
Control who gets access to which areasand at what times
CONCEPTS
VALIDATION GROUP
DOOR SCHEDULE
ANTI-PASSBACK
& STRIKEOUT
TIMEZONE
SPECIAL INFORMATIONSet door schedules, time zones, button schedules and anti-passback timer before programming validation groups.
Up to 15 validation groups can be programmed. Each selects a door schedule, time zone, button schedule and anti-passback option.
Validation group "0" has full access at all times.
?
??
?
BUTTONSCHEDULE
UP TO 15 VALIDATION GROUPS[VG1 - VG15] CAN BE SET
EACH VALIDATION GROUP SELECTSA DOOR SCHEDULE, BUTTON SCHEDULE, TIME ZONE AND ANTI-PASSBACK OPTION
VALIDATION GROUP
12
-
EVENT LOG
Keeps a record of all accesstransactions and supervisory conditions
CONCEPTS10:52:42 06/20/95 0:0 sTx[00001] ->{A} Sherie Price AM/II Unit #110:52:42 06/20/95 0:2 Crd[01470] ->{D} Tony Lobianco Front Door Card Reader10:54:14 06/20/95 0:0 sTx[00003] ->{A} John Phillips AM/II Unit #110:54:21 06/20/95 0:1 Kpd[2003] ->{C} Moe Howard Front Gate Keypad10:54:28 06/20/95 0:0 sTx[00002] ->{A} Jack Hess AM/II Unit #1
EVENT LOG
SPECIAL INFORMATIONThe number of possible stored events depends on the size of memory installed and the amoumt of other data stored.
The stored event log can be set to retain up to 500, 1000, 2000, 5000, maximum or no events.
Stored event log can be printed in total, from the last report or from a selected date.
SAMPLE REAL-TIME EVENT PRINTOUT
Event Log Report Jun 22, 1995 09:56:39 Page 001Installation: South Hills Apartments AM/II Unit #1
08:55:35 06/22/95 0:0 sTx[00003] ->{B} Unit #1
08:51:21 06/22/95 0:2 Crd[01470] ->{B} Front Door Card Reader
08:45:49 06/22/95 0:0 sTx[00001] ->{A} Unit #1
12:28:42 06/20/95 0:0 Obs[1] Obstacle Txmtr Trouble
11:02:42 06/20/95 0:0 Exit Program Mode11:02:42 06/20/95 0:0 Program Mode Timed Out
SAMPLE STORED EVENT LOG
10:52:42 06/20/95 0:0 sTx[00001] ->{A} AM/II Unit #110:52:42 06/20/95 0:2 Crd[01470] ->{D} Front Door Card Reader10:54:14 06/20/95 0:0 sTx[00003] ->{A} AM/II Unit #110:54:21 06/20/95 0:1 Kpd[2003] ->{C} Front Gate Keypad10:54:28 06/20/95 0:0 sTx[00002] ->{A} AM/II Unit #1
REAL-TIME EVENT LOG PRINTS EACH EVENT AS IT HAPPENS
STORED EVENT LOG SHOWS ALL EVENTS FROM MOST RECENT TO OLDEST STORED EVENT
TOP LINE OF EVENT SHOWS:
TIME & DATE
NETWORK ADDRESS : REMOTE DEVICE ADDRESS
MEDIA TYPE & ID#
DIRECTION OF ENTRY & RELAY LETTER
BOTTOM LINE OF EVENT SHOWS: DEVICE NAME
13
-
REMOTE DEVICES
Accept input from various mediaCONCEPTS
REMOTEDEVICE
*
5 6
7 8 9
0 #
1 2 3
4
MODEL AM-KP ENTRY KEYPAD
ACCEPTS ENTRY CODES AS USERS KEY THEM IN
MODEL AM-CRI CARD READER INTERFACE
ACCEPTS CARD CODES FROM ONE OR TWO CARD SWIPE READERS
MODEL AM-RPR RADIO PROXIMITY RECEIVER
ACCEPTS ID CODES FROM TRANSMITTERS AS USERS ACTIVATE THEM NEXT TO RECEIVER
MODEL AM-RRR REMOTE RADIO RECEIVER
ACCEPTS ID CODES FROM TRANSMITTERS AS USERS ACTIVATE THEM WITHIN RANGE OF THE REMOTE RECEIVER'S ANTENNA
EACH REMOTE DEVICE CAN BE WIRED TO THE AM/II AND HAS A ROTARY SWITCH THAT SELECTS THE DEVICE ADDRESS
14
-
ACCESS MEDIA
Cards, keypad codes &transmitters (CCT’s)
HARDWARE & MEDIA
The following pages provide a foundation forlearning the hardware devices and accesscontrol media used in the AM/II system. ACCESS MEDIA
S I N G L E T R A N S M I T T E R S
U N I Q U E L Y C O D E D A T T H E F A C T O R Y A N D P R O G R A M M E D O N E A T A T I M E N O T E : S I N G L E T R A N S M I T T E R S A R E N O T C O M P A T I B L E W I T H A C C E S S B A S E O R A C C O U N T M A N A G E R
B L O C K C O D E D T R A N S M I T T E R S
S E Q U E N T A L L Y C O D E D A T T H E F A C T O R Y A N D P R O G R A M M E D B Y E N T E R I N G T H E S T A R T I N G A N D E N D I N G B L O C K N U M B E R S
B L O C K C O D E D C A R D S
S E Q U E N T A L L Y C O D E D A T T H E F A C T O R Y A N D P R O G R A M M E D B Y E N T E R I N G T H E S T A R T I N G A N D E N D I N G B L O C K N U M B E R S
K E Y P A D E N T R Y C O D E S
P R O G R A M M E D B Y T H E I N S T A L L E R , C A N B E F R O M T W O T O E I G H T D I G I T S L O N G - R E C O M M E N D E D T H A T A L L C O D E S B E T H E S A M E L E N G T H - F O R H I G H E S T S E C U R I T Y , C O D E S S H O U L D B E A T L E A S T F O U R D I G I T S L O N G
15
-
RELAY OUTPUTS & SENSING INPUTS
Control access devices and senseauxiliary inputs
HARDWARE & MEDIA
OUTPUTS & INPUTS
RELAY OUTPUTS
● ELECTRICALLY ISOLATED CONTACTS (3 AMPS, 30 VOLTS MAXIMUM)
● NORMALLY OPEN AND NORMALLY CLOSED CONTACTS
● PROGRAMMABLE FOR TIME DURATION, PULSE, TOGGLE AND LATCH OUTPUTS
SENSING INPUTS
● OPEN REQUEST INPUT AVAILABLE FOR RELAY CHANNELS A & B (NORMALLY OPEN SWITCH)
● DOOR SENSE INPUT AVAILABLE FOR RELAY CHANNELS A & B (NORMALLY CLOSED SWITCH)
B
RELAYCHANNEL "B"
C
RELAYCHANNEL "C"
D
RELAYCHANNEL "D"
A
RELAYCHANNEL "A"
OPENREQUEST
DOORSENSE
DOORSTRIKE
DOORSTRIKE
CONTROLLEDACCESSDOOR 1
CONTROLLEDACCESSDOOR 2
BARRIERGATE
OBSTACLETRANSMITTER
TYPICAL INSTALLATION
PUSHBUTTON MAGNETICSWITCH
16
-
RS-232 PORT
For printing event log, programmingand transferring memory between units
HARDWARE & MEDIARS-232
PORT
MODEL A2MMODEMCABLE
MODEL A2CCOMPUTERCABLE
MODEL A2PPRINTERCABLE
SERIALPRINTER
TERMINAL
PERSONALCOMPUTER
MODEM
SERIAL PRINTER
● P R I N T S R E A L - T I M E E V E N T L O G● P R I N T S S Y S T E M R E P O R T S● U S E M O D E L A 2 P C A B L E
COMPUTER TERMINAL
● D I S P L A Y S R E A L - T I M E E V E N T L O G● D I S P L A Y S S Y S T E M R E P O R T S● L O C A L L Y P R O G R A M A M / I I● U S E M O D E L A 2 C C A B L E
PERSONAL COMPUTER
● D I S P L A Y S R E A L - T I M E E V E N T L O G● D I S P L A Y S S Y S T E M R E P O R T S● L O C A L L Y P R O G R A M A M / I I● S T O R E A M / I I M E M O R Y T O D I S K● L O A D A M / I I M E M O R Y F R O M D I S K● U S E M O D E L A 2 C C A B L E
COMPUTER MODEM
● C O N N E C T S T O A M / I I R S - 2 3 2 P O R T● A N S W E R S C A L L S F R O M R E M O T E C O M P U T E R● R E M O T E L Y P R O G R A M A M / I I● R E M O T E L Y S T O R E A M / I I M E M O R Y T O D I S K● R E M O T E L Y L O A D A M / I I M E M O R Y F R O M D I S K● R E M O T E L Y D I S P L A Y S T O R E D E V E N T L O G● R E M O T E L Y D I S P L A Y S Y S T E M R E P O R T S● U S E M O D E L A 2 M C A B L E
MODEL A2AINTERCONNECTCABLE
AM/II INTERCONNECT
● C O N N E C T S T W O A M / I I U N I T S T O G E T H E R● T R A N S F E R M E M O R Y B E T W E E N U N I T S● U S E M O D E L A 2 A C A B L E
17
-
ACCESS OUT & NETWORK TERMINALS
For linking an AM/II to an externalaccess control panel and connecting
multiple AM/II’s together
HARDWARE & MEDIA
ACCESS OUT& NETWORK
EXPANSION MEMORY CARD
RADIO
DECODE
ACCESS GRANTED
READER KEYPAD
ACCESS OUT DATA
ACCESS IN DATA
ACCESS A
ACCESS B
ACCESS C
OBSTACLE
MAGIC WAND
ACCESS D
BO 1 O 1 O 1 BO 1 N.O. COM. N.C. N.O. COM. N.C. N.O. COM. N.C. N.O. COM. N.C.
EARTHGROUND
ACCESS OUT KEYPAD IN CHANNEL A CHANNEL B CHANNEL C CHANNEL DREADER IN
14 - 24 VAC12 - 35 VDCAC POWER
INPUTDC POWER
INPUTNETWORK
WARNING
RADIO
PERIPHERALS
RELAYS
EXTERNAL CONTROL
RS-232
OFF
ON
POWER
POWER
RESET
DISPLAYCONTRAST
SYSTEM
ACCESS OUT TERMINALS
● PASSES ACCESS OUT INFORMATION TO AN EXTERNAL ACCESS CONTROL SYSTEM
● SUPPORTS WIEGAND26 SECURAKEY31, AND SENTEX30DATA FORMATS
● EXTERNAL ACCESS PANEL CAN BE USED FOR VALIDATION OF PASS-THROUGH DATA FROM THE AM/II
● SIMPLE THREE-WIRE CONNECTION
NETWORK TERMINALS
● UP TO EIGHT AM/II UNITS CAN BE CONNECTED TOGETHER
● EVENT LOG IS SHARED BETWEEN THE NETWORKED UNITS
● SIMPLE TWO-WIRE RS-485 CONNECTION
EXPANSION MEMORY CARD
RADIO
DECODE
ACCESS GRANTED
READER KEYPAD
ACCESS OUT DATA
ACCESS IN DATA
ACCESS A
ACCESS B
ACCESS C
OBSTACLE
MAGIC WAND
ACCESS D
BO 1 O 1 O 1 BO 1 N.O. COM. N.C. N.O. COM. N.C. N.O. COM. N.C. N.O. COM. N.C.
EARTHGROUND
ACCESS OUT KEYPAD IN CHANNEL A CHANNEL B CHANNEL C CHANNEL DREADER IN
14 - 24 VAC12 - 35 VDCAC POWER
INPUTDC POWER
INPUTNETWORK
RADIO
PERIPHERALS
RELAYS
EXTERNAL CONTROL
RS-232
OFF
ON
POWER
POWER
RESET
DISPLAYCONTRAST
SYSTEM
EXPANSION MEMORY CARD
RADIO
DECODE
ACCESS GRANTED
READER KEYPAD
ACCESS OUT DATA
ACCESS IN DATA
ACCESS A
ACCESS B
ACCESS C
OBSTACLE
MAGIC WAND
ACCESS D
BO 1 O 1 O 1 BO 1 N.O. COM. N.C. N.O. COM. N.C. N.O. COM. N.C. N.O. COM. N.C.
EARTHGROUND
ACCESS OUT KEYPAD IN CHANNEL A CHANNEL B CHANNEL C CHANNEL DREADER IN14 - 24 VAC12 - 35 VDC
AC POWERINPUT
DC POWERINPUTNETWORK
RADIO
PERIPHERALS
RELAYS
EXTERNAL CONTROL
RS-232
OFF
ON
POWER
POWER
RESET
DISPLAYCONTRAST
SYSTEM
EXPANSION MEMORY CARD
RADIO
DECODE
ACCESS GRANTED
READER KEYPAD
ACCESS OUT DATA
ACCESS IN DATA
ACCESS A
ACCESS B
ACCESS C
OBSTACLE
MAGIC WAND
ACCESS D
BO 1 O 1 O 1 BO 1 N.O. COM. N.C. N.O. COM. N.C. N.O. COM. N.C. N.O. COM. N.C.
EARTHGROUND
ACCESS OUT KEYPAD IN CHANNEL A CHANNEL B CHANNEL C CHANNEL DREADER IN14 - 24 VAC12 - 35 VDC
INPUTINPUTNETWORK
RADIO
PERIPHERALS
RELAYS
EXTERNAL CONTROL
RS-232
OFF
ON
POWER
POWER
RESET
DISPLAYCONTRAST
SYSTEM
AC POWER DC POWER
MEMORY EXPANSION CARD
MEDIUM (64 K)
SMALL (16 K) LARGE (128 K)
X-LARGE (256 K)
WARNING
TURN THE POWER SWITCH OFF BEFORE INSTALLING ORREMOVING THIS MEMORY EXPANSION CARD
SEVEREELECTRICAL
DAMAGE
MEMORY EXPANSION CARD
MEDIUM (64 K)
SMALL (16 K) LARGE (128 K)
X-LARGE (256 K)
WARNING
TURN THE POWER SWITCH OFF BEFORE INSTALLING ORREMOVING THIS MEMORY EXPANSION CARD
SEVEREELECTRICAL
DAMAGE
MEMORY EXPANSION CARD
MEDIUM (64 K)
SMALL (16 K) LARGE (128 K)
X-LARGE (256 K)
WARNING
TURN THE POWER SWITCH OFF BEFORE INSTALLING ORREMOVING THIS MEMORY EXPANSION CARD
SEVEREELECTRICAL
DAMAGE
MEMORY EXPANSION CARD
MEDIUM (64 K)
SMALL (16 K) LARGE (128 K)
X-LARGE (256 K)
WARNING
TURN THE POWER SWITCH OFF BEFORE INSTALLING ORREMOVING THIS MEMORY EXPANSION CARD
SEVEREELECTRICAL
DAMAGE
18
-
MEMORY UTILITIES
For copying and transferring memorymodule data
HARDWARE & MEDIA
MEMORYUTILITIES
COPYING MEMORY DATA
● MEMORY MODULE INFORMATION CAN BE SENT TO AND RECEIVED FROM ANOTHER AM/II THROUGH THE RS-232 PORT USING THE MODEL A2A CABLE
SENDING AND RECEIVING MEMORY DATA
● MEMORY MODULE DATA CAN BE SENT AND RECEIVED THROUGH THE RS-232 PORT OVER THE PHONE LINE USING A MODEM WITH THE MODEL A2M CABLE
● MEMORY MODULE DATA CAN ALSO BE SENT AND RECEIVED THROUGH THE RS-232 PORT WITH A PERSONAL COMPUTER DIRECTLY CONNECTED TO THE AM/II USING THE MODEL A2C CABLE
RADIO
DECODE
ACCESS GRANTED
READER KEYPAD
ACCESS OUT DATA
ACCESS IN DATA
ACCESS A
ACCESS B
ACCESS C
OBSTACLE
MAGIC WAND
ACCESS D
BO 1 O 1 O 1 BO 1 N.O. COM. N.C. N.O. COM. N.C. N.O. COM. N.C. N.O. COM. N.C.
EARTHGROUND
ACCESS OUT KEYPAD IN CHANNEL A CHANNEL B CHANNEL C CHANNEL DREADER IN
14 - 24 VAC12 - 35 VDCAC POWER
INPUTDC POWER
INPUTNETWORK
RS-232
OFF
ON
POWER
POWER
RESET
DISPLAYCONTRAST
RADIO
DECODE
ACCESS GRANTED
READER KEYPAD
ACCESS OUT DATA
ACCESS IN DATA
ACCESS A
ACCESS B
ACCESS C
OBSTACLE
MAGIC WAND
ACCESS D
BO 1 O 1 O 1 BO 1 N.O. COM. N.C. N.O. COM. N.C. N.O. COM. N.C. N.O. COM. N.C.
EARTHGROUND
ACCESS OUT KEYPAD IN CHANNEL A CHANNEL B CHANNEL C CHANNEL DREADER IN 14 - 24 VAC12 - 35 VDC
AC POWERINPUT
DC POWERINPUTNETWORK
OFF
ON
POWER
RESET
DISPLAYCONTRAST
MODEL A2ACABLE
MODEM
PERSONAL COMPUTER
MODEL A2MCABLE
MODEL A2CCABLE
MEMORY EXPANSION CARD
MEDIUM (64 K)
SMALL (16 K) LARGE (128 K)
X-LARGE (256 K)
WARNING
TURN THE POWER SWITCH OFF BEFORE INSTALLING ORREMOVING THIS MEMORY EXPANSION CARD
SEVEREELECTRICAL
DAMAGE
MEMORY EXPANSION CARD
MEDIUM (64 K)
SMALL (16 K) LARGE (128 K)
X-LARGE (256 K)
WARNING
TURN THE POWER SWITCH OFF BEFORE INSTALLING ORREMOVING THIS MEMORY EXPANSION CARD
SEVEREELECTRICAL
DAMAGE
RADIO
DECODE
ACCESS GRANTED
READER KEYPAD
ACCESS OUT DATA
ACCESS IN DATA
ACCESS A
ACCESS B
ACCESS C
OBSTACLE
MAGIC WAND
ACCESS D
BO 1 O 1 O 1 BO 1 N.O. COM. N.C. N.O. COM. N.C. N.O. COM. N.C. N.O. COM. N.C.
EARTHGROUND
ACCESS OUT KEYPAD IN CHANNEL A CHANNEL B CHANNEL C CHANNEL DREADER IN
14 - 24 VAC12 - 35 VDCAC POWER
INPUTDC POWER
INPUTNETWORK
RS-232
OFF
ON
POWER
POWER
RESET
DISPLAYCONTRAST
MEMORY EXPANSION CARD
MEDIUM (64 K)
SMALL (16 K) LARGE (128 K)
X-LARGE (256 K)
WARNING
TURN THE POWER SWITCH OFF BEFORE INSTALLING ORREMOVING THIS MEMORY EXPANSION CARD
SEVEREELECTRICAL
DAMAGE
RADIO
DECODE
ACCESS GRANTED
READER KEYPAD
ACCESS OUT DATA
ACCESS IN DATA
ACCESS A
ACCESS B
ACCESS C
OBSTACLE
MAGIC WAND
ACCESS D
BO 1 O 1 O 1 BO 1 N.O. COM. N.C. N.O. COM. N.C. N.O. COM. N.C. N.O. COM. N.C.
EARTHGROUND
ACCESS OUT KEYPAD IN CHANNEL A CHANNEL B CHANNEL C CHANNEL DREADER IN
14 - 24 VAC12 - 35 VDCAC POWER
INPUTDC POWER
INPUTNETWORK
RS-232
OFF
ON
POWER
POWER
RESET
DISPLAYCONTRAST
MEMORY EXPANSION CARD
MEDIUM (64 K)
SMALL (16 K) LARGE (128 K)
X-LARGE (256 K)
WARNING
TURN THE POWER SWITCH OFF BEFORE INSTALLING ORREMOVING THIS MEMORY EXPANSION CARD
SEVEREELECTRICAL
DAMAGE
19
-
PRE-INSTALLATION PLANNINGBefore beginning, take time to plan the installation.✶ Make a sketch of the installation floor plan showing all
controlled access points.✶ Select a good location to mount the AM/II.✶ Determine a good location for the antenna.✶ Select locations for the remote accessory devices (keypads,
card readers, remote receivers, proximity receivers).✶ Research possible places for wire runs to accessories and
access devices.
INSTALLATION OUTLINEThe following outline is intended to guide you through theinstallation of an AM/II system.
1. Unpack the system. Identify the system components(transformer, antenna, etc.).
2. Plan the installation by creating an installation diagram.3. Mount the AM/II (in an optional cabinet if required).4. Connect the antenna.5. Install any remote accessory devices.6. Wire connections to the AM/II terminals.
A. Install a ground stake and run the ground wire or usea cold water pipe as earth ground for the AM/II.
B. Connect relay outputs to the access device(s) to becontrolled.
C. Turn AM/II POWER switch off and connect theplug-in transformer or connect the AM/II to a14-24 VAC or 12-35 VDC auxiliary power supply.
D. Turn the POWER switch on. The green POWERindicator should light.
E. Adjust the display contrast as desired.7. Program the system.8. Test the system.9. Adjust the red RADIO RANGE knob to limit the maximum range
of the receiver.
LOBBY
AC
CO
UN
TIN
G
SERVICE
SALES
PRESIDENT
V.P.V.P.
SALES PURCH.
ENGINEERING
BATH BATH
CO
MP
UT
ER
RO
OM
STOR.
COPIERAREA
CHIEFENG.
LAB
20
-
WIRELESS INSTALLATION TIPSSignals Through Construction MaterialsWhen installing any wireless system, certain limitations mustbe considered. Low power wireless UHF transmitter signals willnot broadcast equally through all types of constructionmaterials. The AM/II contains a receiver that should allowreception of the transmitters in almost all locations. Refer tofigure showing approximate signal strength that will occur withdifferent types of building materials.
Transmitters in VehiclesThe radio range of a transmitter will also be affected when thetransmitter is located in a vehicle. Depending on the locationof the transmitter (on the visor, on the dash, in the centerconsole) the range will vary. Most of the signal strengthchanges are related to the amount of metal in close proximityto the transmitter. If a transmitter is clipped to the top of thedriver’s sun visor, with the visor flipped up, placing thetransmitter between the metal roof and the metal reinforcedvisor, the transmitters range will be reduced.
PRE-INSTALLATIONUnpacking the SystemThe basic AM/II system package includes the followingaccessories:✶ Plug-in Transformer. Provides low voltage power to the
access control panel.✶ Mounting Screws. Used to mount the AM/II inside the
cabinet.
Installing the Memory ModuleFour sizes of memory modules are available for the AM/II:✶ SMALL (16K) MEMORY✶ MEDIUM (64K) MEMORY✶ LARGE (128K) MEMORY✶ X-LARGE (256K) MEMORYOne of the memory modules must be installed for the AM/II tofunction.✘ CAUTION! Be sure the AM/II is disconnected from power
or that the AM/II’s POWER switch is off before removingof replacing the memory module.
STEP 1 With the system power off, plug the memory moduleinto the AM/II.
STEP 2 Secure the memory module with two screws.
90% - 100%OF FULL POWER
65% - 95%OF FULL POWER
10% - 70%OF FULL POWER
WALLBOARD ANDWOOD STUDS
CONCRETE WITH STEELREINFORCEMENT OR
METAL LATH AND PLASTER
LIGHT CONCRETEOR BRICK
AM/II UNIT WITH MEMORY INSTALLED
PLUG-INTRANSFORMER
CASE MOUNTINGSCREWS
RADIO
DECODE
ACCESS GRANTED
READER KEYPAD
ACCESS OUT DATA
NETWORK DATA
ACCESS A
ACCESS B
ACCESS C
OBSTACLE
MAGIC WAND
ACCESS D
BO 1 O 1 O 1 BO 1 N.O. COM. N.C. N.O. COM. N.C. N.O. COM. N.C. N.O. COM. N.C.
EARTHGROUND
ACCESS OUT KEYPAD IN CHANNEL A CHANNEL B CHANNEL C CHANNEL DREADER IN 14 - 24 VAC12 - 35 VDC
AC POWERINPUT
DC POWERINPUTNETWORK
OFF
ON
POWER
RESET
DISPLAYCONTRAST
MEMORY EXPANSION CARD
MEDIUM (64 K)
SMALL (16 K) LARGE (128 K)
X-LARGE (256 K)
WARNING
TURN THE POWER SWITCH OFF BEFORE INSTALLING ORREMOVING THIS MEMORY EXPANSION CARD
SEVEREELECTRICAL
DAMAGE
INSTALL MEMORYMODULE
21
-
MOUNT UNITThe AM/II can be mounted indoors directly to a wall or in theModel CAB-1 indoor cabinet. For outdoor mounting, the ModelCAB-2 weather resistant cabinet is recommended. The twocabinets both provide some security for the unit.Each cabinet has wiring knockouts for connection to wiringconduit.
STEP 1 Decide on a good location (near power and goodwiring access) to mount the AM/II. It should be in asecure location. The mounting area should bebetween -22 and +149 degrees Fahrenheityear-around.
STEP 2 If a cabinet is used, punch out the conduit knockoutsas required for the installation. Attach the cabinet tothe wall with the appropriate fasteners.
STEP 3 Secure the AM/II with three screws.
DIRECT MOUNTING
FOR INDOOR INSTALLATIONSTHE AM/II CAN BE MOUNTEDDIRECTLY USING THREESCREWS AND APPROPRIATESCREW ANCHORS
DRIVE FOUR SCREWS INTOWALL AT THESE LOCATIONS(LEAVE SCREW HEAD 1/8" OUTFROM WALL)
USE PLASTIC SCREWANCHORS IF REQUIRED
HANG CABINET ON SCREWS
DIRLL A HOLE AND DRIVE A FIFTH SCREWINTO THE HOLE TOLOCK CABINET TO WALL
8"
8-3/4"
CAB-1 MOUNTING
MOUNT AM/II UNIT INTOCABINET WITH THREESCREWS SUPPLIED
EXPANSION MEMORY CARD
RADIO
DECODE
ACCESS GRANTED
READER KEYPAD
ACCESS OUT DATA
ACCESS IN DATA
ACCESS A
ACCESS B
ACCESS C
OBSTACLE
MAGIC WAND
ACCESS D
BO 1 O 1 O 1 BO 1 N.O. COM. N.C. N.O. COM. N.C. N.O. COM. N.C. N.O. COM. N.C.
EARTHGROUND
ACCESS OUT KEYPAD IN CHANNEL A CHANNEL B CHANNEL C CHANNEL DREADER IN14 - 24 VAC12 - 35 VDC
AC POWERINPUT
DC POWERINPUTNETWORK
OK
WARNINGSEVERE
ELECTRICALDAMAGE
T U R N T H E P O W E R S W I T C H O F F B E F O R E I N S T A L L I N G O RR E M O V I N G T H I S M E M O R Y E X P A N S I O N C A R D
MEMORY EXPANSION CARD
RADIO
PERIPHERALS
RELAYS
EXTERNAL CONTROL
RS-232
OFF
ON
POWER
POWER
RESET
DISPLAYCONTRAST
SYSTEM
SMALL MEDIUM LARGE
PUNCH OUT REQUIREDCONDUIT CONNECTIONKNOCKOUTS FOR ANTENNA,POWER, GROUND AND SIGNALS
CAB-2 MOUNTING
CAB-2 MOUNTS WITH FOURSCREWS AT THESE LOCATIONS
USE PLASTIC SCREWANCHORS OR CONCRETEWEDGE ANCHORS
9"
9"
PUNCH OUT REQUIREDCONDUIT CONNECTIONKNOCKOUTS FOR ANTENNA,POWER, GROUND AND SIGNALS
EXPANSION MEMORY CARD
RADIO
DECODE
ACCESS GRANTED
READER KEYPAD
ACCESS OUT DATA
ACCESS IN DATA
ACCESS A
ACCESS B
ACCESS C
OBSTACLE
MAGIC WAND
ACCESS D
BO 1 O 1 O 1 BO 1 N.O. COM. N.C. N.O. COM. N.C. N.O. COM. N.C. N.O. COM. N.C.
EARTHGROUND
ACCESS OUT KEYPAD IN CHANNEL A CHANNEL B CHANNEL C CHANNEL DREADER IN14 - 24 VAC12 - 35 VDC
AC POWERINPUT
DC POWERINPUTNETWORK
OK
WARNINGSEVERE
ELECTRICALDAMAGE
T U R N T H E P O W E R S W I T C H O F F B E F O R E I N S T A L L I N G O RR E M O V I N G T H I S M E M O R Y E X P A N S I O N C A R D
MEMORY EXPANSION CARD
RADIO
PERIPHERALS
RELAYS
EXTERNAL CONTROL
RS-232
OFF
ON
POWER
POWER
RESET
DISPLAYCONTRAST
SYSTEM
SMALL MEDIUM LARGE
MOUNT AM/II UNIT INTOCABINET WITH THREESCREWS SUPPLIED
22
-
EARTH GROUND & POWER CONNECTIONSEarth GroundFor the best ground, use size 14 gauge solid wire or larger toconnect the EARTH GROUND terminal to an 8-foot copperground rod. Locate the ground rod next to the Power andTelephone company rods and bond the rods together with anew clamp. Do not disturb the clamps installed by thePower or Telephone Company.Alternately, connect the EARTH GROUND terminal to a coldwater pipe or to the GND terminal on the AC transformer.
PowerThe AM/II is powered by a 16.5 Volt, 20 VA to 50 VA, internallyfused, UL listed, Class 2 transformer. This transformer isincluded with the AM/II system pack.The system can alternately be powered from a 12-35 VDC or14-24 VAC auxiliary power supply. Refer to the chart below forselecting wire size for the distance to the power source.Typically DC power is used when battery backed-upuninterruptable operation is required. The externally chargedbattery must be capable of supplying the power requirementsof the AM/II and it’s complement of devices.✘ WARNING! Never short the terminals of the transformer
together. This will cause the internal fuse to blow. Thetransformer must be connected to a 120 VAC 60 Hzunswitched (24 hour) power outlet not controlled by awall switch.
STEP 1 Be sure that the AM/II POWER switch is off.STEP 2 Connect the transformer to the AC terminals or
connect the AM/II to the operator’s auxiliary poweroutput.
✘ WARNING! Do not connect both AC and DC power.STEP 3 If used, plug transformer into AC outlet and secure
with case screw (if provided).☞ NOTE: Never power door strikes or other high current
magnetic devices from the same power source as the AM/II.
AM/IIEARTHGROUNDTERMINAL
AM/II & POWER CO.GROUND STAKESBONDED TOGETHER
14 GASOLID
DO NOTDISTURBPOWER CO.GROUND!
A COLD WATER PIPEOR THE AC TRANSFORMERGND TERMINAL MAY ALSOBE USED FOR EARTH GROUND
POWEROFF
ON
EARTHGROUND
14 - 24 VAC12 - 35 VDC
AC POWERINPUT
DC POWERINPUT
TRANSFORMER16 VAC, 20 VA
AC
AC
GND
CONNECT EITHERAC OR DC POWER
NOT BOTH!
POWER WIRE DISTANCE MINIMUM WIRE SIZE
1-50 FEET 18 AWG
51-150 FEET 16 AWG
151-250 FEET 14 AWG
251-500 FEET 12 AWG
23
-
REMOTE DEVICE WIRING REQUIREMENTSCable TypeEach remote device requires a 6-wire connection to the AM/II.Depending on the distance of the cable run, two different typesof cable are recommended.✶ For cable distance up to 300 feet, use BELDEN 9931
(24 AWG).✶ For cable distance up to 500 feet, use WEICO 9405
(20 AWG).
Load NumberEach hardwired remote accessory device has been assigneda “load number”. Homerun wiring is recommended foraccessories, although multiple accessories can be wired on thesame cable run if the following formulas are used.✶ For cable distance up to 300 feet:
CABLE RUN IN FEET x LOAD UNITS = 3,000 OR LESS✶ For cable distance up to 500 feet:
CABLE RUN IN FEET x LOAD UNITS = 10,000 OR LESS
REMOTE DEVICE LOAD NUMBER
AM-KP 9
AM-RRR 4
AM-CRI 25
AM-RPR 4
24
-
ANTENNA HOOK-UPIf using a remote antenna, construct the antenna kit asdescribed in its instructions. Mount the antenna as high aspossible. Connect the coax lead to the AM/II antennaconnector. Up to 25 feet of coax cable may be used to connectthe antenna.☞ NOTE: Mount the antenna at least 10 feet from the AM/II
control.
REMOTE RADIO RECEIVER CONNECTIONSThe Model AM-RRR remote radio receiver can be used toextend the radio range and remote the radio input of the AM/II.Use the AM-RRR with its local whip antenna or with theEXA-1000 or EXA-2000 remote antennas.The receiver is connected to the READER IN terminals on theAM/II. Follow the instructions supplied with the remote receiverand the hook-up diagram shown.The DEVICE ADDRESS SELECTOR switch in the unit selectsthe device address. It must be set from 1-6, and be differentfrom any other remote accessory device.
ANTENNAMOUNTEDAS HIGHAS POSSIBLE
CO-AX TORECEIVER
U-BOLT
2" MAXDIA.
ATTIC MOUNTING POST MOUNTING
(RE
D)
(BLK
)
(GR
N)
(WH
T)
(BLU
)
(OR
G/Y
EL)
PW
RG
ND
DA
T1
DA
T0
DV
AL
CLK
RADIORANGECONTROL
RADIOSIGNALINDICATOR
ACCESS GRANTEDINDICATORRED = POWERGREEN = ACCESS
DEVICEADDRESSSELECTOR
ANTENNACONNECTOR
EXA-2000DIRECTIONALANTENNAMOUNTEDON WOODPOST
25
-
REMOTE KEYPAD CONNECTIONSThe Model AM-KP access control keypads can be used formanual code entry for the AM/II. The keypad can be mountedon a pedestal or directly to a wall.The keypad is connected to the KEYPAD IN terminals on theAM/II. Follow the instructions supplied with the keypad and thehook-up diagram shown.The DEVICE ADDRESS SELECTOR switch in the unit selectsthe device address. It must be set from 1-6, and be differentfrom any other remote accessory device.
REMOTE PROXIMITY RECEIVERThe Model AM-RPR proximity receiver can be used forultra-short range transmitter reception at access portals. Thetransmitter will have to be activated right next to this receiverto activate it. The receiver is mounted in a single-gang plasticoutlet box.The receiver is connected to the READER IN terminals on theAM/II. Follow the instructions supplied with the proximityreceiver and the hook-up diagram shown.The DEVICE ADDRESS SELECTOR switch in the unit selectsthe device address. It must be set from 1-6, and be differentfrom any other remote accessory device.
*
5 6
7 8 9
0 #
1 2 3
4
FOR LOCAL POWER,DISCONNECT RED WIRE ANDCONNECT EXTERNAL 12 VDC
POWER SUPPLY TO PWR & GND
BO 1 O O
O1 1
1 B
BO 1
PWR GND DAT1 DAT0 DVAL CLKG
RN
BLK
WH
T
BLU
OR
G/Y
EL
RED
PWR
GND
DAT1
DAT0
DVAL
CLK
AM/II TERMINALS
B
AM-RPR
26
-
CARD READER INTERFACEThe Model AM-CRI card reader interface can support two cardreaders. It would be located between the card readers and theAM/II, usually near the card readers.The card reader is connected to the READER IN terminals onthe AM/II. Follow the instructions supplied with the keypad andthe hook-up diagram.Two rotary switches in the unit selects the device address foreach card reader. They must be set to different numbers from1-6, and also be different from any other remote accessorydevice.
CONTROL INPUTSOpen RequestThe open request terminals for relays A & B are available forconnection to an external switch. When the switch closes toground, if the relay channel is not locked closed, the relay willactivate.Common uses would be with a knox box, pushbutton, or keylock where someone would need to open the access portalfrom inside the controlled area.
Door SenseThe door sense terminals for relays A & B are used withnormally closed door contacts. The contacts monitor theposition of the access door. When the door opens, the contactsopen.Door sensing is required to use the door ajar and door relockfeatures. Door sensing can detect when a door is propped openand cause an alarm relay to activate when the door is openlonger than the door ajar time. Door sensing also detects whenthe door is closed, deactivating the control relay the momentthe door closes.
AM-CRI
PWR
GND
DAT1
DATO
DVAL
CLK(RED)
(BLK)
(GRN)
(WHT)
(BLU)
(ORG/YEL)
CARD READER "B"DEVICE ADDRESS SELECTOR
(1-6)
MAG LOCK
OPEN REQUESTPUSHBUTTON
N.O. COM. N.C. N.O. COM. N.C.
CHANNEL A CHANNEL B
CHANNEL "A"OPEN REQUESTPUSHBUTTON
CHANNEL "B"OPEN REQUESTPUSHBUTTON
AM/IITERMINALS
CONTACT OPENS WHENDOOR OPENS AND MOVESMAGNET AWAY FROM SWITCH N.O. COM. N.C. N.O. COM. N.C.
CHANNEL A CHANNEL B
CHANNEL "A"DOOR SENSECONTACT
CHANNEL "B"DOOR SENSECONTACT
(DOORCLOSED)
(DOOROPEN)
AM/IITERMINALS
27
-
RELAY OUTPUT CONNECTIONSThe AM/II provides four relay outputs. Each relay has isolated,dry contact, Form “C” (N/O & N/C) contacts rated at 3 amps30 volts maximum.
Relay Operation OptionsRelays can be programmed for access control, alarm contactshunting, alarm triggering, obstacle triggering and CCTVtriggering. Relay wiring method depends on the option selectedand the type of device controlled.
Control Relay OptionRelays programmed with the control option will activate whenaccess is granted to access media. Relays set with the controloption would be connected to access devices (door strikes,mag-locks, automatic operators, etc.).☞ NOTE: Relay channels “A” & “B” are always set as control
relays.
Shunt Relay OptionRelay channels “C” & “D” can be programmed for shuntoperation. A shunt relay would be wired across a set of alarmcontacts, shunting their operation, preventing the alarm fromtriggering when genuine access is granted. If the door or gateis forced open, without having access granted by the AM/II, thealarm would be triggered.When programmed for shunt operation, relay channel “C” willmirror the activation of relay channel “A”. Relay channel “D” willmirror the activation of relay channel “B”.
ELECTRICDOOR
STRIKE
N.O. COM. N.C.
CHANNEL ARELAY CHANNEL
A, B, C OR D
DOOR STRIKEHOOK-UP
TRANSFORMEROR POWER
SUPPLY FORDOOR STRIKE
NOTE: REFER TO DOOR STRIKEINSTRUCTIONS FOR ANYSPECIAL HOOK-UP REQUIREMENTS
MAGNETICDOORLOCK
N.O. COM. N.C.
CHANNEL ARELAY CHANNEL
A, B, C OR D
MAG LOCKHOOK-UP
TRANSFORMEROR POWER
SUPPLY FORMAG LOCK
NOTE: REFER TO DOOR LOCKINSTRUCTIONS FOR ANYSPECIAL HOOK-UP REQUIREMENTS
N.O. COM. N.C.
CHANNEL ARELAY CHANNEL
A, B, C OR D
DOOR OR GATEOPERATORHOOK-UP
DOOR ORGATE
OPERATOR
1
2
3
WIRE RELAY OUTPUT TO OPERATOR"PUSHBUTTON" OR "RADIO" INPUT
NOTE: REFER TO OPERATORINSTRUCTIONS FOR ANYSPECIAL HOOK-UP REQUIREMENTS
N.O. COM. N.C.RELAY CHANNEL
C OR D
SHUNT RELAYHOOK-UP
N/CDOORALARM
CONTACT
CHANNEL C
RELAY CHANNEL "C" SHUNTS FOR RELAY CHANNEL "A"RELAY CHANNEL "D" SHUNTS FOR RELAY CHANNEL "B"
WHEN RELAY CHANNEL "C" OR "D" ACTIVATES, IT SHUNTS THE ALARM CONTACT PREVENTING THE ALARM FROM TRIGGERINGWHEN THE DOOR IS OPENED
TO ALARMCONTROLPANEL
28
-
Alarm Relay OptionRelay channels “C” & “D” can be programmed for alarmoperation. An alarm relay would be wired to a noisemaker orto the loop input of an alarm control panel.Relay channel “C” can function as an alarm relay for relaychannel “A”. Relay channel “D” can function as an alarm relayfor relay channel “B”. The door sense input must be wired forrelay channel “A” and/or “B” for the alarm relay function to work.If door “A” or “B” is held open longer than the Door Ajar Timetime programmed, the alarm relay for the appropriate relaychannel will activate.
Obstacle Relay OptionRelay channels “C” & “D” can function as obstacle relays whenModel MGT obstacle transmitters are used. Relay channel “C”activates for MGT obstacle transmitter #1, relay channel “D”activates for MGT obstacle transmitter #2.Obstacle relays are used to trigger obstacle inputs onautomatic door and gate operators. Triggering the obstacleinput will reverse or stop the operator.
CCTV Relay OptionRelay channels “C” & “D” can function as CCTV relays. Theycan be used only when a Model AE-1 or AE-2 telephone entrymodule is installed with the AM/II.When a telephone connection is made to a directory party, theycan press the “5" digit on their telephone to activate the CCTVrelay. A CCTV camera would activate to send a picture of theentry area to the directory party.
N.O. COM. N.C.RELAY CHANNEL
C OR D
ALARM RELAYHOOK-UP
ALARMCONTROL
PANEL
CHANNEL C
RELAY CHANNEL "C" ALARMS FOR RELAY CHANNEL "A"RELAY CHANNEL "D" ALARMS FOR RELAY CHANNEL "B"
TRANSFORMEROR POWER
SUPPLY FORNOISEMAKER
NOISEMAKER
N.O. COM. N.C.
CHANNEL C
RELAY CHANNELC OR D
ALARM RELAY ACTIVATES WHEN DOOR IS OPEN LONGER THAN DOOR AJAR TIME OR WHEN DOOR IS FORCED OPEN WITHOUT VALID ACCESS BEING GRANTED
GATEOPERATOROBSTACLE
INPUT
N.O. COM. N.C.RELAY CHANNEL
C OR D
OBSTACLE RELAYHOOK-UP
CHANNEL C
RELAY CHANNEL "C" ACTIVATES FOR OBSTACLE TX #1RELAY CHANNEL "D" ACTIVATES FOR OBSTACLE TX #2
WHEN RELAY ACTIVATES, IT TRIGGERS THE OBSTACLE INPUT OF THE OPERATOR, STOPPING OR REVERSING THE OPERATOR
WIRE RELAY OUTPUT TO OPERATOROBSTACLE INPUT
NOTE: REFER TO OPERATORINSTRUCTIONS FOR ANYSPECIAL HOOK-UP REQUIREMENTS
CCTVCAMERA
IRIS ENABLE
N.O. COM. N.C.RELAY CHANNEL
C OR D
CCTV RELAYHOOK-UP
CHANNEL C
WHEN RELAY ACTIVATES, IT ALLOWS THE CAMERA TO SEND VIDEO TO THE DIRECTORY PARTY'S MONITOR
WIRE RELAY OUTPUT TO CAMERAIRIS ENABLE OR VIDEO ENABLE INPUT
NOTE: REFER TO CCTV CAMERAINSTRUCTIONS FOR ANYSPECIAL HOOK-UP REQUIREMENTS
29
-
RS-232 PORT CONNECTIONSThe AM/II RS-232 port can be used to connect to a serial inputline printer, a personal computer, modem or data terminal.
Printer Connections☞ NOTE: The installation of a printer is optional. The AM/II may
be used without a printer if activity logging is not required.The AM/II can connect to virtually any standard personalcomputer printer that accepts a 9600 baud serial RS-232 input.Connecting a printer to the AM/II allows for a printed copy ofeach transmitter activation showing the transmitter number,time and date of activation as well as the various systemreports. Use the Model A2P cable to connect the AM/II to aprinter.Personal computer printers contain switches for setting theprinter’s data format and options. The printer’s switches mustbe set correctly to match the output of the AM/II before theprinter will function properly. Refer to the specific printer’sinstruction manual for the location and possible settings of theprinter’s switches.The printer may have additional options that may or may notbe useful with the AM/II.The printer options that must be set are:✶ Baud Rate 9600✶ 8 Data Bits✶ No Parity✶ 1 Stop Bit✶ No Auto Line Feed after Carriage Return✶ X-ON/X-OFF Data Flow Control
2
3
7
20
8-PIN
2
1
8
6
RD
TD
GND
CTS
DB-25 SIGNALTD
RD
GND
DTR
SIGNAL
AM/IIPRINTER
MALEDB-25
8-PINMODULAR
PIN 1
A2P CABLE
RADIO
DECODE
ACCESS GRANTED
READER KEYPAD
ACCESS OUT DATA
ACCESS IN DATA
ACCESS A
ACCESS B
ACCESS C
OBSTACLE
MAGIC WAND
ACCESS D
BO 1 O 1 O 1 BO 1 N.O. COM. N.C. N.O. COM. N.C. N.O. COM. N.C. N.O. COM. N.C.
EARTHGROUND
ACCESS OUT KEYPAD IN CHANNEL A CHANNEL B CHANNEL C CHANNEL DREADER IN14 - 24 VAC12 - 35 VDC
AC POWERINPUT
DC POWERINPUTNETWORK
OFF
ON
POWER
RESET
DISPLAYCONTRAST
MEMORY EXPANSION CARD
MEDIUM (64 K)
SMALL (16 K) LARGE (128 K)
X-LARGE (256 K)
WARNING
TURN THE POWER SWITCH OFF BEFORE INSTALLING ORREMOVING THIS MEMORY EXPANSION CARD
SEVEREELECTRICAL
DAMAGE
MODEL A2CCABLE
SAMPLE REAL-TIME EVENT PRINTOUT
10:52:42 06/20/95 0:0 sTx[00001] ->{A} AM/II Unit #110:52:42 06/20/95 0:2 Crd[01470] ->{D} Front Door Card Reader10:54:14 06/20/95 0:0 sTx[00003] ->{A} AM/II Unit #110:54:21 06/20/95 0:1 Kpd[2003] ->{C} Front Gate Keypad10:54:28 06/20/95 0:0 sTx[00002] ->{A} AM/II Unit #1
REAL-TIME EVENT LOG PRINTS EACH EVENT AS IT HAPPENS
TOP LINE OF EVENT SHOWS:
TIME & DATE
NETWORK ADDRESS : REMOTE DEVICE ADDRESS
MEDIA TYPE & ID#
DIRECTION OF ENTRY & RELAY LETTER
Event Log Report Jun 22, 1995 09:56:39 Page 001Installation: South Hills Apartments AM/II Unit #1
08:55:35 06/22/95 0:0 sTx[00003] ->{B} Unit #1
08:51:21 06/22/95 0:2 Crd[01470] ->{B} Front Door Card Reader
08:45:49 06/22/95 0:0 sTx[00001] ->{A} Unit #1
12:28:42 06/20/95 0:0 Obs[1] Obstacle Txmtr Trouble
11:02:42 06/20/95 0:0 Exit Program Mode11:02:42 06/20/95 0:0 Program Mode Timed Out
SAMPLE STORED EVENT LOG
STORED EVENT LOG SHOWS ALL EVENTS FROM MOST RECENT TO OLDEST STORED EVENT
BOTTOM LINE OF EVENT SHOWS: DEVICE NAME
PIN 1 PIN 2 PIN 3 PIN 4 PIN 5 PIN 6 PIN 7 PIN 8
SENDDATA
RECIEVEDATA
REQUESTTO SEND
N/C N/C CLEARTO SEND
N/C GROUND
8-PIN MODULARPLUG PINOUT
30
-
Personal Computer and Data Terminal Connections☞ NOTE: The installation of a personal computer (PC) or data
terminal for event logging and system programming isoptional, but recommended. Programming the AM/II is mucheasier, especially when using names, with a PC or dataterminal.
The AM/II can connect to virtually any PC’s serial port. Use theModel A2C-DB25 (25-pin) or A2C-DB9 (9-pin) cable to connectthe AM/II to a computer.When using a data terminal, connecting the cable and settingthe terminal port options is all that’s required. When using aPC, a communications program (AccessBase, AccountManager, Windows Terminal, Procomm, Quick Link,BitComm, etc.) must be used to communicate with the AM/II.The computer’s software will have settings for the PC’s portoptions. The software port options must be set correctly tomatch the output of the AM/II before the PC software willfunction properly. Refer to the specific software’s instructionsfor details on how to set the port options.The serial port (COM port) options that must be set are:✶ Baud Rate 9600✶ 8 Data Bits✶ No Parity✶ 1 Stop Bit✶ X-ON/X-OFF Data Flow ControlSetting the AM/II RS-232 port output to the “PRINTER” optionwill show the ongoing event log on the computer screen.Setting the AM/II RS-232 port output to the “TERMINAL” optionwill allow the computer to access the AM/II just like thekeyboard on the AM/II. The only keyboard differences whenusing a PC or terminal to access the AM/II are:✶ The ENTER key equals the AM/II’s OK key.✶ The ESCAPE (Esc) key is similar the AM/II’s * (star) key.
Press ESCAPE twice to enter program mode, once to jumpback to the main menu.
✶ The A-Z & 0-9 keys are used for character inputs.✶ Hold the CONTROL (Ctrl) key and press “Z” to exit
programming.
Modem Connections☞ NOTE: The installation of a modem is optional. It will allow
remote programming of the AM/II.The AM/II can connect to most personal computer externalmodems. Use the Model A2M cable to connect the AM/II to amodem. Connection to a modem allows you to call the AM/IIover the telephone with a personal computer and anothermodem. All of the same programming functions that can beperformed locally can be made remotely, off-site. Systemreports and the event log can be retrieved remotely.
2
3
7
20
8-PIN
2
1
8
6
RD
TD
GND
CTS
DB-25 SIGNALTD
RD
GND
DTR
SIGNAL
AM/IICOMPUTER
FEMALEDB-25
PIN 1
8-PINMODULAR
A2C-DB25 CABLE
RADIO
DECODE
ACCESS GRANTED
READER KEYPAD
ACCESS OUT DATA
NETWORK DATA
ACCESS A
ACCESS B
ACCESS C
OBSTACLE
MAGIC WAND
ACCESS D
BO 1 O 1 O 1 BO 1 N.O. COM. N.C. N.O. COM. N.C. N.O. COM. N.C. N.O. COM. N.C.
EARTHGROUND
ACCESS OUT KEYPAD IN CHANNEL A CHANNEL B CHANNEL C CHANNEL DREADER IN14 - 24 VAC12 - 35 VDC
AC POWERINPUT
DC POWERINPUTNETWORK
OFF
ON
POWER
RESET
DISPLAYCONTRAST
MEMORY EXPANSION CARD
MEDIUM (64 K)
SMALL (16 K) LARGE (128 K)
X-LARGE (256 K)
WARNING
TURN THE POWER SWITCH OFF BEFORE INSTALLING ORREMOVING THIS MEMORY EXPANSION CARD
SEVEREELECTRICAL
DAMAGE
MODEL A2CCABLE
RADIO
DECODE
ACCESS GRANTED
READER KEYPAD
ACCESS OUT DATA
NETWORK DATA
ACCESS A
ACCESS B
ACCESS C
OBSTACLE
MAGIC WAND
ACCESS D
BO 1 O 1 O 1 BO 1 N.O. COM. N.C. N.O. COM. N.C. N.O. COM. N.C. N.O. COM. N.C.
EARTHGROUND
ACCESS OUT KEYPAD IN CHANNEL A CHANNEL B CHANNEL C CHANNEL DREADER IN14 - 24 VAC12 - 35 VDC
AC POWERINPUT
DC POWERINPUTNETWORK
OFF
ON
POWER
RESET
DISPLAYCONTRAST
MEMORY EXPANSION CARD
MEDIUM (64 K)
SMALL (16 K) LARGE (128 K)
X-LARGE (256 K)
WARNING
TURN THE POWER SWITCH OFF BEFORE INSTALLING ORREMOVING THIS MEMORY EXPANSION CARD
SEVEREELECTRICAL
DAMAGE
MODEL A2CCABLE
3
2
7
5
4
8-PIN
2
1
8
6
3
RD
TD
GND
CTS
RTS
DB-25 SIGNAL
RD
TD
GND
CTS
RTS
SIGNAL
AM/IIMODEM
MALEDB-25
8-PINMODULAR
PIN 1
A2M CABLE
FEMALEDB-9
PIN 1
8-PINMODULAR
3
2
5
4
6
8
7
8-PIN
2
1
8
6
A2C-DB9 CABLE
RD
TD
GND
CTS
DB-9 SIGNALTD
RD
GND
DTR
DSR
CTS
RTS
SIGNAL
AM/IICOMPUTER
31
-
ACCESS OUT CONNE