Wireless Access Point

1750Mbps

WIRELESS AP/ROUTER

QUICK INSTALLATION GUIDE

Introduction

This Quick Start Guide is designed to guide you through installation and includes warranty terms.

Package Contents

1.Wireless Access Point2.Gigabit PoE with Mounting Bracket3.Power Cord4.Ethernet cable5.Fitting screws5.Quick Start Guide6.Certificate of approval

Installation Requirements

• CAT5/6 cable• Phillips screwdriver• Drill and drill bit (6 mm for wall-mounting or 3 mm for ceiling-mounting)• Optional: Drywall or keyhole saw (to cut 18 mm hole for Ethernet cable feed)TERMS OF USE: All Ethernet cabling runs must use CAT5 (or above). It is the customer‘s responsibility to follow local country regulations, including operation within legal frequency channels, output power, indoor cabling requirements, and Dynamic Frequency Selection (DFS) requirements.

Installation Diagram

Solution 1

Data Center & Cloud Computing Infrastructure Solution

POE POWER SUPPLY

AP

Internet

Solution 2

Data Center & Cloud Computing Infrastructure Solution

Note: Solution 1 (Single Device Setting): Get into the web setting page independently.Solution 2 (Multiple Devices Setting): Do centralized management settings and local portal by AC core gateway. (POE power supply and other devices are not standard, please refer to the packing list. )

……

…………

AP AP AP AP

Internet

AC CORE GATEWAY

CORE SWITCH

POE SWITCH POE SWITCH

Connection Diagram

Note: Set the LAN port of the device to the computer.

POE Power Supply(Not Standard)

Higher Level Network

RESET WAN

LED Color States

White Power on

Red WAN port connected

Blue Wifi signal received

Hardware OverviewLED

Data Center & Cloud Computing Infrastructure Solution

Installation Diagram

Ceiling Installation

Wall Installation

② let the AP and chassis docking

③ installation over① the chassis is removed, whichis fixed on the chiling with four screws

② let the AP and chassis docking

③ installation over① the chassis is removed, whichis fixed on the wall with four screws

Note: This quick installation guide is taken the circled ceiling AP for an example. Some of square ceiling AP have 4 screws and please push one side to install.

ceiling

wall wall wall

ceiling ceiling

Data Center & Cloud Computing Infrastructure Solution

The single-pack of the Wireless AP includes one Gigabit PoE adapter. For multi-pack units, we recommend using a Switch.1. Connect the Ethernet cable from the Wireless AP to the adapter’s POE port.2. Connect an Ethernet cable from your LAN to the adapter’s LAN port.3. Connect the Power Cord to the adapter‘s power port. Connect the other end of the Power Cord to a power outlet.

Data Center & Cloud Computing Infrastructure Solution

Connecting Power over Ethernet

Specifications:

Hardware Specifications

Chipset: Qualcomm QCA9558+QCA9880+AR8035; 720Mhz CPU Ram: DDR2 256MB; Flash: 16MB； PA: 2.4G SE2576L, 5.8G SE5003L1-R; Built in Watchdog Chipset

Antenna Built in 6*3dBi Antenna Transmission Rate 2.4GHz: 450Mbps; 5GHz: 1300Mbps

RF Parameters

Output Power (Max): 500mW(27dBm); Receiving Sensitivity (Max): -96dBm; Frequency: 802.11ac/n/a: 5.18-5.825GHz; 802.11b/g/n: 2.412GHz-2.4835GHzVC

Modulation Mode

DSSS: DBPSK@1Mbps, DQPSK@2Mbps, CCK@5.5/11Mbps; OFDM: BPSK@6/9Mbps, QPSK@12/18Mbps, 16-QAM@24Mbps, 64-QAM@48/54Mbps;MIMO-OFDM (11n): MCS 0-23; MIMO-OFDM (11ac): MCS 0-29

Modulation Way

11b: DSS: CCK@5.5/11Mbps, DQPSK@2Mbps,DBPSK@1Mbps; 11a/gOFDM: 64QAM@48/54Mbps,16QAM@24Mbps, QPSK@12/18Mbps,

BPSK@6/9Mbps11n: MIMO-OFDM:BPSK,QPSK,16QAM,64QAM;

11ac: MIMO-OFDM:BPSK,QPSK,16QAM,64QAM,256QAM

Physical Ports

1* 10/1000Mbps WAN RJ45 Ethernet Port; Support POE Power Supply;

1* RESET / WPS Button

Indicator Three Color Indicator

PowerPower Supply: IEEE802.3at POE Power Supply(0-100m); Power adapter: 48V 0.5A POE Power Adapter(Configured)

Power Consumption(Max) IP Index IP31

<24W

MTBF >250000HInstallation Way Ceiling-mounted, Wall -mounted

Case Plastic Case (Imported ABS Material)Physical Features Size: 220*220*45mm; Weight: 0.38Kg

Working Environment

Working Temperature: -10C~65C; Storage Temperature: -40C~70C;Operation Humidity: 10%~90%RH Non condensing;Storage Humidity: 5%~95%RH Non condensing

1. Compliance is required with respect to voltage, frequency, and currentrequirements indicated on the manufacturer’s label. Connection to a different power source than those specified may result in improper operation, damage to the equipment or pose a fire hazard if the limitations are not followed.2. There are no operator serviceable parts inside this equipment. Service should be provided only by a qualified service technician.3. This equipment is provided with a detachable power cord which has an integral safety ground wire intended for connection to a grounded safety outlet.a. Do not substitute the power cord with one that is not the provided approved type. Never use an adapter plug to connect to a 2-wire outlet as this will defeat the continuity of the grounding wire.b. The equipment requires the use of the ground wire as a part of the safety certification, modification or misuse can provide a shock hazard that can result in serious injury or death.c. Contact a qualified electrician or the manufacturer if there are questions about the installation prior to connecting the equipment.d. Protective earthing is provided by Listed AC adapter. Building installation shall provide appropriate short-circuit backup protection.e. Protective bonding must be installed in accordance with local national wiring rules and regulations.

Data Center & Cloud Computing Infrastructure Solution

Safety Notices

Electrical Safety Information

1. Read, follow, and keep these instructions.2. Heed all warnings.3. Only use attachments/accessories specified by the manufacturer.

WARNING: Do not use this product in location that can be submerged by water.

WARNING

WARNING: Avoid using this product during an electrical storm. There may be a remote risk of electric shock from lightning.

WARNING

The above warranty does not apply if the Product:1. Has been modified and/or altered, or an addition made thereto, except by the personnel outside the company's authorized representative or without the written permission of the company.2. Has been painted, rebranded or physically modified in any way;3. Has been damaged due to errors or defects in cabling;4. Has been subjected to misuse, abuse, negligence, abnormal physical, electromagnetic or electrical stress, including lightning strikes, or accident;5. Has been damaged or impaired as a result of using third party firmware;6. Has not been received by the company within 30 days of issuance of the RMA.In addition, the above warranty shall apply only if: the product has been properly installed and used at all times in accordance, and in all material respects, with the applicable Product documentation; all Ethernet cabling runs use CAT5 (or above), and for outdoor installations, shielded Ethernet cabling is used, and for indoor installations, indoor cabling requirements are followed.ReturnsNo Products will be accepted for replacement or repair without obtaining a Return Materials Authorization (RMA) number from the company during the warranty period, and the Products being received at the company's facility freight prepaid in accordance with the RMA process of the company. Products returned without an RMA number will not be processed and will be returned freight collect or subject to disposal.

Data Center & Cloud Computing Infrastructure Solution

The company warrants that the products (hereinafter referred to as “the products") shall not be defective in materials and workmanship within one (1) year from the date of delivery, in accordance with the products provided below (hereinafter referred to as “products") under normal use and operation. In accordance with the foregoing guarantee, the sole obligation and responsibility of the company is to repair or replace any product that does not conform to the guarantee contents in the above warranty period according to its judgment. This warranty does not include the removal and reinstallation of any product. The warranty period of the product after repair or replacement shall not exceed its initial warranty period.

Limited Warranty

Warranty Conditions

Data Center & Cloud Computing Infrastructure Solution

Changes or modifications not expressly approved by the party responsiblefor compliance could void the user’s authority to operate the equipment.This device complies with Part 15 of the FCC Rules. Operation is subject tothe following two conditions.1. This device may not cause harmful interference, and2. This device must accept any interference received, includinginterference that may cause undesired operation.This equipment has been tested and found to comply with the limits for aClass B digital device, pursuant to Part 15 of the FCC Rules. These limits aredesigned to provide reasonable protection against harmful interference ina residential installation. This equipment generates, uses and can radiateradio frequency energy and, if not installed and used in accordance withthe instructions, may cause harmful interference to radio communications.However, there is no guarantee that interference will not occur in aparticular installation. If this equipment does cause harmful interferenceto radio or television reception, which can be determined by turningthe equipment off and on, the user is encouraged to try to correct theinterference by one or more of the following measures:• Reorient or relocate the receiving antenna.• Increase the separation between the equipment and receiver.• Connect the equipment into an outlet on a circuit different from that towhich the receiver is connected.• Consult the dealer or an experienced radio/TV technician for help.Operations of this equipment in a residential area is likely to causeharmful interference in which case the user will be required to correct theinterference at his own expense.This radio transmitter (FCC: SWX-UAPACL) has been approved by FCCto operate with the antenna types listed below with the maximumpermissible gain and required antenna impedance for each antenna typeindicated. Antenna types not included in this list, having a gain greaterthan the maximum gain indicated for that type, are strictly prohibited foruse with this device.Antenna Information: Dual-band antenna, Gain: 3 dBi

Compliance

FCC

Data Center & Cloud Computing Infrastructure Solution

CE marking on this product represents the product is in compliance with alldirectives that are applicable to it.Alert Sign (!) Follows CE MarkingAlert sign must be indicated if a restriction on use applied to the productand it must follow the CE marking.

The antennas used for this transmitter must be installed to provide aseparation distance of at least 20 cm from all persons and must not belocated or operating in conjunction with any other antenna or transmitter.

RF Exposure Warning

CE Marking

European Directive 2002/96/EC requires that the equipment bearingthis symbol on the product and/or its packaging must not be disposedof with unsorted municipal waste. The symbol indicates that thisproduct should be disposed of separately from regular household wastestreams. It is your responsibility to dispose of this and other electric andelectronic equipment via designated collection facilities appointed by thegovernment or local authorities. Correct disposal and recycling will helpprevent potential negative consequences to the environment and humanhealth. For more detailed information about the disposal of your oldequipment, please contact your local authorities, waste disposal service, orthe shop where you purchased the product.

RoHS/WEEE Compliance Statement

Contact Us

Room 2702, Yisibo Software Building,Xinhaiyi, No.2 Haitian Road, Yuehai Street, Nanshan, District, Shenzhen, China

Tel: +86（755）83571351

820 SW 34th Street Bldg W7 Suite H, Renton, WA 98057,United States

Tel: +1 (877) 205 5306

China North America

1220 Tung Chun CommercialCentre, Shanghai Street 438-444,Kowloon, HongKong

Tel: +(852) 5808 7203

Building 7, NOVA Neufahrn Gewerbepark, Am Gfild7, 85375, Neufahrn bei Freising, Munich

Tel: +49 (0) 89 414176412

Hong Kong Germany

Addresses, phone number and fax number also have been listed at www.fs.com. Please e-mail us at sales@fs.com or call us for assistance. All statements, technical information, and recommendations related to the products here are based upon information believed to be reliable or accurate. However, the accuracy or completeness thereof is not guaranteed, and no responsibility is assumed for any inaccuracies. Please contact FS for more information.