ws-1216 manual
TRANSCRIPT
8/13/2019 WS-1216 manual
http://slidepdf.com/reader/full/ws-1216-manual 1/8
MICA HEATING BO
SAUNA ROOM
Model : WS-1216
INSTRUCTION MANUAL
No advanced advice will be submit before we change our design and size.
The pictures may be a little different from the real products.
Our company keep the final explanation right.
8/13/2019 WS-1216 manual
http://slidepdf.com/reader/full/ws-1216-manual 2/8
141
1. Users should read through this manual before assembly
and use.
2. The product must install a reliable earth line and
electricity leak protection.
3. Users should install power supply according to actual
condition.
4. Patients with hypertension or drunk are not permitted to
use this products.
5. Adult guidance is necessary for children or under age to
use sauna.
6. Corrosive liquid are not allowed to bring into the room.
7. Sauna room must not over working for long time. Theheat pipe may damage of long time heating.
8. Our company would not take responsibility if the product
is damaged but caused by violating the normal operating
procedures.
9. When the product is discarded, please deal with it
ATTENTION
TECHNICAL PARAMETERS
1. rated voltage: AC380V±10% 50Hz /60Hz
2.Power of Sauna heater: 6000w3. Size: 2000X1200X1900mm
1800X1200X1900mm
1600X1200X1900mm
T e m p e r a t u r e
S e n s o r w i r e
S i g n a l w i r e
S p e
a k e r
( w h
i t e c o n n e c t o r )
1 2 V l i t t l e l e d
w i r e
( r e d c o n n e c t o r )
L e d L a m p
D r i v e r
P o w e r i n p u t c a b l e
S a u n a s t o v e w i r e
2 2 0 V e x p l o s i o n p r o o f
l a m p w i r e ( r e d
c o n n e c t o r )
L e d
Circuit Diagram
8/13/2019 WS-1216 manual
http://slidepdf.com/reader/full/ws-1216-manual 3/8
2
Schematic Diagram
13
The whole view
Top view
13.Backrest board
installation. Locked screws when the board closed after the upper culture stone .
14. Install the lower culture
stone . Locked the screwswhen the lower culture stoneclosed after the backrest board .
15.Finish the saunaroom installationby locking thesolid wood roofcover
8/13/2019 WS-1216 manual
http://slidepdf.com/reader/full/ws-1216-manual 4/8
8/13/2019 WS-1216 manual
http://slidepdf.com/reader/full/ws-1216-manual 5/8
411
INSTALLATION DIAGRAM
1.Put the backplaneon the level floor.
2.Put the back side wallon the backplaneinside the groove.
10. Install the upper apron .
Install the upper big seat frame. Put a small partof the seat frame into the seat support shelf, and closed to the wood Fang already in the right side wall. Lock the screws as attached drawing.
8/13/2019 WS-1216 manual
http://slidepdf.com/reader/full/ws-1216-manual 6/8
5 10
5
3.Put the rightside wall onthe backplaneinside thegroove , andlock the 2pcsside wall
together with 3parts specialscrew .Onepart of thescrew alreadyinstall on theright side wall .
3 part special screw installa tion
7.Put the seat support
shelf on left side & right side
9. Install the upper small seatframe . Put a small par t of theseat frame into the seat support shelf, and closed to the wood Fang already in the right side wall. Lock the screws as attached drawing.
8/13/2019 WS-1216 manual
http://slidepdf.com/reader/full/ws-1216-manual 7/8
BA C
3 parts screws
3.Tooth C is already ins talled in the right sidewall , firstly pls. lock the B part into the tooth C.Second ly , align the left panel hole , 2 plateclose to each other at 90 degree .Thirdly , put
A part to the corresponding hole in left side
6
little leds
cable hole
9
6.Tooth C is already installed in the right side wall.Firstl y , pls. lock the B part into the tooth C ; Secondly ,align the back side wall hole , 2 plate close to each otherat 90 degree ; Thirdly , put a part to the correspondinghole in the back side panel .
explosion-proof lamp
8/13/2019 WS-1216 manual
http://slidepdf.com/reader/full/ws-1216-manual 8/8
4.Put the front glass panel on the backplane inside the groove, connect the front glass panel & left side wall ,right side wall together by 3 parts screws .Installation procedure, pls. refer to the side wallconnection.
7
5.Roof installation.Lock the screws on the roof as the above drawing. Before the roof installation, pls. pull outthe lamp cable to the roof through correspondinghole. After locking the screws on the roof , theglass door panel is stationary .
8