wsk tilt switch - woosens.comtel:+86-755-83439588 fax:+86-755-83433488 addr:rm309, 3f,kanghesheng...
TRANSCRIPT
The WSK tiltswitch is a low power, high performance electrionic switch which
combined dual axes accelerometer and Woosnes’s advanced algorithm in a single
module.
WSK tilt switch has a UART interface, it is for factory calibration and configuration only, The customer configure
the tilt switch by themselves is not advised, the alarm angle is configured in the factory.
WSK Tilt Switch
Product introduction
Characteristic
· High Performance · TTL logic level output · Free configuration
· Two-tone LED lamp · Set Zero function · Plastic shiled
· Operating temperature-40~85℃
Application
Level adjustmentOverhead working truck
Product specification
Electrical Parameters
Min Typical Max Unit
9
-40
30
-40
12 35
+85
40
+90
V
mA
℃
℃
Parameter Condition
Supply Voltage
Power consumption
Operating temperature
Storage temperature
Construction Machinery
· IP65 shiled
Room 309,Kanghesheng Bldg,New Energy Innovation Industrail Park,No.1,Chuangsheng Road,Nanshan district,Shenzhen 518055,P.R. China 1
WEB:www.sensorexpert.com.cnTEL:+86-755-83439588 FAX:+86-755-83433488
The shell structure parameters(mm)
Performance
Parameter Condition Specification
Direction
Range
Output Resolution
repeatability
Offset
Cross axis error
Bandwidth
Relatvie Accuracy ±30°,25℃
X-Y
± 30°
0.004°
0.02°
Max 0.1°
Max 4%, tye 2%
10Hz
0.2°
Remark:Relative accuracy is measured in room temperature at 25℃
Default communication parameter 9600, n, 8, 1
Installation Guide
Room 309,Kanghesheng Bldg,New Energy Innovation Industrail Park,No.1,Chuangsheng Road,Nanshan district,Shenzhen 518055,P.R. China 2
WEB:www.sensorexpert.com.cnTEL:+86-755-83439588 FAX:+86-755-83433488
Note: 1. Please check the interface definition before power on, make sure the connection is the right way. 2. Fix the module with two φ5 screws. 3. Make sure the axes(X,Y) is the same with the measure direction. 4. The installation must be operated by specific personnel.
for standard model number
Selection guide
①WSK
WSK Series tilt switch wiring configuration
The interface definition
Red Blue Brown Black
VIN RXD GNDTXD
Operation Guide
③ x axis alarm angle set,if the alarm angle is 2.5 degree,can be expressed as 025
⑤ y axis alarm angle set,if the alarm angle is 3.0degree,can be expressed as 030
⑦ xx express as 10,when the angle beyond the alarm angle, the output TTL level would change after 1s delay
⑨ 5H express high level at alarm stauts, 5L exress low level at alarm status.
Yellow
OUT
②-
③XXX
④-
⑤XXX
⑥-
⑦XX
⑧-
⑨5X
Status Red lamp Remarks
Normal
Normal to alarm
Alarm
Alarm to Normal
Default:1s,Configurable
Default:1s,Configurable
Green lamp
Light off
Ligth off
Light on
Flash
Light on
Flash
Light off
Light off
Remark:RXD and TXD are the communication port for factory calibration.
Room 309,Kanghesheng Bldg,New Energy Innovation Industrail Park,No.1,Chuangsheng Road,Nanshan district,Shenzhen 518055,P.R. China 3
WEB:www.sensorexpert.com.cnTEL:+86-755-83439588 FAX:+86-755-83433488
for customization number
①WSK
②xxx
③x
② xxx express the customer’s number, for example 027 means the 27th customer of Woosens,xxx is from 001-999
③ x express the item number of the customer, including the confiure information of the product, x is from 1-9,A-Z
Zero setting operation: press and hold the zero setting button of the tilt switch, and the traffic light and greenlight of the inclination switch will flash alternately for 5 seconds, and the red light and green light will be onat the same time, and the green light indication state will be restored after 2S, indicating that the zero setting is successful.The zero setting button should be released.
Contact us
Hongkong
Chongqing
Shenzhen
Chengdu
Beijing
Shanghai
Room 309,Kanghesheng Bldg,New Energy Innovation Industrail Park,No.1,Chuangsheng Road,Nanshan district,Shenzhen 518055,P.R. China 4
WEB:www.sensorexpert.com.cnTEL:+86-755-83439588 FAX:+86-755-83433488
Addr:Rm309, 3F,Kanghesheng bldg, New Energy Innovation
Industrial Park,No.1, Chuangsheng Rd, Nanshan District, Shenzhen
518055, P.R, China .
Postal code:518055
Tel:(86)755-83439588
Fax:(86)755-83439588
E-mail:[email protected]
Tel:(86)18321998351
E-mail:[email protected]
Tel:(86)13637913617
E-mail:[email protected]
Tel:(86)15884550295
E-mail:[email protected]
Tel:(86)(86)15223083879
Fax:(86)23-67736110
E-mail:[email protected] Tel:(852)2420855
Fax:(852)24200055
E-mail:[email protected]
Shenzhen headquarters
Shanghai office
Beijing office Chengdu office
Chongqing office HongkongAddr:Room 2216, 22 / F, New Technology Plaza,
34 Dayou street, San Po Kong, Kowloon, Hong Kong