xj 314 chapt1b
TRANSCRIPT
8/14/2019 XJ 314 Chapt1b
http://slidepdf.com/reader/full/xj-314-chapt1b 1/14
Shearing and Bearing Stress 1
Shearing and Bearing
Stress (1.6-1.8, 1.12)MAE 314 – Solid MechanicsXiaoning Jiang
8/14/2019 XJ 314 Chapt1b
http://slidepdf.com/reader/full/xj-314-chapt1b 2/14
Shearing and Bearing Stress 2
What is Shearing Stress?
We learned about normalstress ( σ) , which actsperpendicular to thecross-section.
Shear stress ( τ ) acts
tangential to the surfaceof a material element.
Normal stress resultsin a volume change.
Shear stress resultsin a shape change.
8/14/2019 XJ 314 Chapt1b
http://slidepdf.com/reader/full/xj-314-chapt1b 3/14
Shearing and Bearing Stress 3
Where Do Shearing Stresses Occur?
Shearing stresses are commonly found in bolts, pins, andrivets.
Free Body Diagram of Bolt
Bolt is in “single” shear
Force P results in shearing stress
Force F results in bearing stress (will discuss later)
8/14/2019 XJ 314 Chapt1b
http://slidepdf.com/reader/full/xj-314-chapt1b 4/14
Shearing and Bearing Stress 4
We o not assume τ is uniform over the cross-section,because this is not the case.
τ is the average shear stress.
The maximum value of τ may be considerably greaterthan τ ave , which is important for design purposes.
Shear Stress Defined
A
F
A
P ave
8/14/2019 XJ 314 Chapt1b
http://slidepdf.com/reader/full/xj-314-chapt1b 5/14
Shearing and Bearing Stress 5
Double Shear
Free Body Diagram of Bolt Free Body Diagram of Centerof Bolt
A
F
A
F
A
P
ave 22
Bolt is in “double” shear
8/14/2019 XJ 314 Chapt1b
http://slidepdf.com/reader/full/xj-314-chapt1b 6/14
Shearing and Bearing Stress 6
Bearing Stress
Bearing stress is a normal stress , not a shearing stress.
Thus,
where
Ab = projected area where bearing pressure is appliedP = bearing force
td P
A P
b
b
Single shear case
8/14/2019 XJ 314 Chapt1b
http://slidepdf.com/reader/full/xj-314-chapt1b 7/14
Shearing and Bearing Stress 7
Equilibrium of Shear Stresses Consider an infinitesimal element of material. Apply a single shearstress, τ 1.
Total shear force on surface is ( τ 1)bc .
For equilibrium in the y-direction, applyτ 1 on (-) surface.
For moment equilibrium about the z-axis,apply τ 2 on top and bottom surfaces.
Moment equilibrium equation about z-axis:
Thus, a shear stress must be balanced by three other stresses for theelement to be in equilibrium.
1
2
2
1
bacabc )()( 21
21
8/14/2019 XJ 314 Chapt1b
http://slidepdf.com/reader/full/xj-314-chapt1b 8/14
Shearing and Bearing Stress 8
Equilibrium of Shear Stresses
1
2
2
1
Face Direction ShearStress
+ + +
+ - -
- - +
- + -
What does this tell us?Shear stresses on opposite (parallel) faces of an element are equal inmagnitude and opposite in direction.Shear stress on adjacent (perpendicular) faces of an element are equal inmagnitude and both point towards or away from each other .
Sign convention for shear stressesPositive face – normal is in (+) x, y, or z directionNegative face - normal is in (-) x, y, or z direction
+
++
+
8/14/2019 XJ 314 Chapt1b
http://slidepdf.com/reader/full/xj-314-chapt1b 9/14
Shearing and Bearing Stress 9
σx = stress in x-direction applied in the plane normal to x-axisσ y = stress in y-direction applied in the plane normal to y-axisσ z = stress in z-direction applied in the plane normal to z-axisτ xy = stress in y-direction applied in the plane normal to x-axisτ xz = stress in z-direction applied in the plane normal to x-axisτ zy = stress in y-direction applied in the plane normal to z-axisAnd so on…
Define General State of Stress y
z x
8/14/2019 XJ 314 Chapt1b
http://slidepdf.com/reader/full/xj-314-chapt1b 10/14
Shearing and Bearing Stress 10
There are 9 components of stress:σx, σ y, σ z, τ xy, τ xz, τ yx, τ yz, τ zx, τ zy
As shown previously, in order to maintain equilibrium:τ xy= τ yx, τ xz = τ zx, τ yz = τ zy
There are only 6 independent stress components.
Define General State of Stress y
z x
8/14/2019 XJ 314 Chapt1b
http://slidepdf.com/reader/full/xj-314-chapt1b 11/14
Shearing and Bearing Stress 11
Example Problem
A load P = 10 kips is applied to a rod supported as shownby a plate with a 0.6 in. diameter hole. Determine the shearstress in the rod and the plate.
8/14/2019 XJ 314 Chapt1b
http://slidepdf.com/reader/full/xj-314-chapt1b 12/14
Shearing and Bearing Stress 12
Example Problem
Link AB is used to support the end of a horizontal beam. If link AB issubject to a 10 kips compressive force determine the normal andbearing stress in the link and the shear stress in each of the pins.
ind
int
inb
1
41
2
8/14/2019 XJ 314 Chapt1b
http://slidepdf.com/reader/full/xj-314-chapt1b 13/14
Shearing and Bearing Stress 13
Allowable Dimension or Load
Given dimension allowable load/stress: lower load/stress value to beconsidered for a safe design
Given load/stress allowable dimension: larger dimension (cross-section)value to be considered
Example:1. A structure design uses wood and steel rods with the same diameters.
The allowable stress of wood and steel are 70 MPa and 140 MPa,respectively. Consider a load of 1000 N for these rods, what should bethe designed diameter?
2. Given diameter and allowable stresses maximum load?
8/14/2019 XJ 314 Chapt1b
http://slidepdf.com/reader/full/xj-314-chapt1b 14/14
14
Key Concepts
• Shear stress
• Bearing stress
•
Components of stress• Allowable stress
Next reading: 1.11-1.13